Schneider Electric Exxact User Guide

Add to My manuals
30 Pages

advertisement

Schneider Electric Exxact User Guide | Manualzz

Exxact Connected Multiwire Universal

Rotary Dimmer LED

Device user guide

Information about features and functionality of the devices

0

8

/2022

www.se.com

Legal Information

The Schneider Electric brand and any trademarks of Schneider Electric SE and its subsidiaries referred to in this guide are the property of Schneider Electric SE or its subsidiaries. All other brands may be trademarks of their respective owners.

This guide and its content are protected under applicable copyright laws and furnished for informational use only. No part of this guide may be reproduced or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), for any purpose, without the prior written permission of

Schneider Electric.

Schneider Electric does not grant any right or license for commercial use of the guide or its content, except for a non-exclusive and personal license to consult it on an "as is" basis. Schneider Electric products and equipment should be installed, operated, serviced, and maintained only by qualified personnel.

As standards, specifications, and designs change from time to time, information contained in this guide may be subject to change without notice.

To the extent permitted by applicable law, no responsibility or liability is assumed by

Schneider Electric and its subsidiaries for any errors or omissions in the informational content of this material or consequences arising out of or resulting from the use of the information contained herein.

Table of Contents

Safety information

.......................................................................................5

Exxact - Connected Multiwire Universal Rotary Dimmer LED

.............6

For your safety ...........................................................................................6

About the device.........................................................................................7

Installing the device ....................................................................................7

Pairing the device .......................................................................................7

Pairing device manually.........................................................................7

Pairing device with auto scan.................................................................9

Checking the type of wiring mode ..............................................................10

Configuring the device ..............................................................................10

Changing the device icon ....................................................................10

Renaming the device .......................................................................... 11

Changing the device location ............................................................... 11

Managing dimmer settings...................................................................12

Removing the device ................................................................................14

Resetting the device .................................................................................15

Using the device .......................................................................................15

Switching/Dimming the device manually ...............................................16

Switching/Dimming the device using app ..............................................16

Creating a schedule ............................................................................17

Creating a moment .............................................................................18

Creating an automation .......................................................................20

LED Indication..........................................................................................25

Troubleshooting .......................................................................................26

Technical Data .........................................................................................26

DUG_Exxact MW Rotary Dimmer_WSE-00 3

Safety information

Safety information

Important information

Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it. The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.

The addition of either symbol to a “Danger” or “Warning” safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that accompany this symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Failure to follow these instructions will result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE

NOTICE is used to address practices not related to physical injury.

DUG_Exxact MW Rotary Dimmer_WSE-00 5

Exxact - Connected Multiwire Universal Rotary Dimmer LED

Exxact - Connected Multiwire Universal Rotary

Dimmer LED

6

WDE00X961

For your safety

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

Safe electrical installation must be carried out only by skilled professionals.

Skilled professionals must prove profound knowledge in the following areas:

- Connecting to installation networks.

- Connecting several electrical devices.

- Laying electric cables.

- Safety standards, local wiring rules and regulations.

Failure to follow these instructions will result in death or serious injury.

DANGER

RISK OF FATAL INJURY FROM ELECTRIC SHOCK

The output may carry electric current even when the load is switched Off.

Disconnect the device from the supply by means of the fuse in the incoming circuit before working on the device.

Failure to follow these instructions will result in death or serious injury.

CAUTION

THE DEVICE MAY BE DAMAGED

Only connect dimmable load.

Failure to follow these instructions can result in injury or equipment damage.

DUG_Exxact MW Rotary Dimmer_WSE-00

Exxact - Connected Multiwire Universal Rotary Dimmer LED

About the device

The Connected Multiwire Universal Rotary Dimmer LED (hereinafter referred to as

Rotary Dimmer ) has a rotary knob that can be used to switch and dim ohmic, inductive or capacitive loads manually or remotely. It can detect the load automatically and provides thermal protection, overload-resistance and shortcircuit protection.

Control options

Home control : To control the dimmer through the Wiser app you will need the

Wiser Gateway.

Direct operation : The dimmer can always be controlled directly on-site. You can also connect any number of mechanical push buttons to control the device.

Installing the device

Refer to the installation instruction supplied with this product.

See Connected Multiwire Universal Rotary Dimmer LED .

Pairing the device

Using the Wiser app, pair your device with the Gateway to access and control the device. You can either add the device manually or do an auto-scan to pair it.

Pairing device manually

Follow the steps to pair the device manually:

1. On Home page, tap + icon.

2. Tap icon and select the Wiser Hub .

3. Select any one of the options to add device (A):

– Add Device with Install Code

– Add Device without Install Code

Add Device

Install Code is Recommended

To enhance network security, we strongly recommend using Install Code to add a device.

If you are unable to scan or type the Install

Code, you can still add the device without it.

Add Device with Install Code

Add Device without Install Code

A

DUG_Exxact MW Rotary Dimmer_WSE-00 7

Exxact - Connected Multiwire Universal Rotary Dimmer LED

4. To add the device with Install Code, tap Add Device with Install Code button to open the slide-up menu. Select any one of the options (B):

– Scan Install Code - You can scan the device for the Install Code

– Enter Install Code Manually - You can manually enter the install code from the device

After adding the device with Install Code, proceed to Step 6 .

8

B

Enter Install Code Manually

Cancel

TIP: It is highly recommended to add the device with Install code.

5. To add the device without Install Code, tap Add Device without Install

Code .

6. Remove the knob from the device.

7. Short press the dimmer button 3 times (< 0,5 s) on the device.

3× < 0,5 s

The LED blinks amber.

8. In the app, select Confirm LED is blinking amber and tap Start configuration (C).

Cancel

How to pair device

1

2

C

The app displays the progress of connecting the device.

DUG_Exxact MW Rotary Dimmer_WSE-00

Exxact - Connected Multiwire Universal Rotary Dimmer LED

9. Wait for a few seconds until the device is connected and the app shows that the device is added successfully.

The solid green LED on the rotary dimmer shows that it is successfully connected to the Gateway .

10. After the device is added in the app, tap Done .

Pairing device with auto scan

Pairing the device with auto scan automatically discovers the device when the corresponding device is powered on.

Follow the steps to pair the device:

1. On the Home page, tap + icon.

2. Tap Auto scan tab and tap Confirm .

3. If you have multiple hubs, do Step 4 or proceed to Step 5.

4. Tap Select hub and select the Wiser hub from the slide-up menu.

5. Remove the knob from the device.

6. Short press the push button 3 times (< 0,5 s).

NOTE:

• The LED blinks amber.

• Wait for a few seconds until the device search is complete.

7. Tap Rotary Dimmer and tap Next (A).

Auto Scan

Next

A

8. Once the device is added successfully, tap Done .

DUG_Exxact MW Rotary Dimmer_WSE-00 9

Exxact - Connected Multiwire Universal Rotary Dimmer LED

Checking the type of wiring mode

Using the Wiser app, you can check whether the dimmer is connected with or without neutral wire.

Follow the steps to check the type of wiring mode:

1. On the Home page, tap All devices > Rotary Dimmer .

2. Tap icon and tap Device information .

You see the type of wiring mode (A) in the app.

Virtual ID: bf9019d2978aac84f0ajay copy

MAC Address: 680AE2FFFE1179AD

A

Wiring Mode: With neutral wire

NOTE: Virtual ID and MAC address may vary with the device.

Configuring the device

Changing the device icon

Using the Wiser app, you can change the icon of the device.

Follow the steps to change the device icon:

1. On the Home page, tap All devices > Rotary Dimmer .

2. Tap icon and tap .

3. Tap Icon to view the menu.

4. In the slide-up menu, select any one of the following (A):

– Take photo - Allows you to take a photo from the mobile camera

– Select from Icon Library - Allows you to select an icon from the app library

– Select from Album - Allows you to select photo from the mobile gallery

10

A

DUG_Exxact MW Rotary Dimmer_WSE-00

Exxact - Connected Multiwire Universal Rotary Dimmer LED

5. Tap on the required photo/icon to change the icon.

Renaming the device

Using the Wiser app, you can rename your device for easy identification.

Follow the steps to rename the device:

1. On the Home page, tap All devices > Rotary Dimmer .

2. Tap icon and tap .

3. Tap Name , enter the name (A) and tap Save .

A

Rename

Cancel

Save

Changing the device location

Using the Wiser app, you can change the location of the device.

Follow the steps to change the device location:

1. On the Home page, tap All devices > Rotary Dimmer .

2. Tap icon and tap .

3. Tap Location , select any location from the list (A) and tap Save .

Device location Save

A

Kitchen

DUG_Exxact MW Rotary Dimmer_WSE-00 11

Exxact - Connected Multiwire Universal Rotary Dimmer LED

Managing dimmer settings

Using the Wiser app, you can manage the Dimmer modes and settings.

Follow the steps to access the dimmer settings:

1. On the Home page, tap All devices > Rotary Dimmer .

2. On the device control panel page, tap Settings .

Dimming mode

You can change the dimming mode in the app if you have problems with light flickering. This improves the dimming quality.

Tap Dimming Mode (A) and select either of the following:

– Auto - When any other load is connected to the dimmer (e.g. filament bulb).

– RL-LED - Select the mode only when the LED is not working properly in Auto mode.

NOTE: Refer to

technical data, page 26

for more information.

A

Dimming Mode

Auto

RL-LED

Cancel

Dimming range

You can restrict the maximum and minimum brightness of the load connected to the device. This is done to avoid flickering and switching off the LED.

Tap Dimming Range (B) and do either or both of the following:

– Min Brightness - Drag the slider bar to restrict the minimum brightness.

NOTE: The minimum brightness level should be lower than maximum brightness level.

TIP: If you set the minimum brightness to the right most position on this slider bar, then the load glows at this minimum brightness value even when you drag the sliding bar in the control panel to the bottom most position (for more information refer to

control panel, page 15 ).

12 DUG_Exxact MW Rotary Dimmer_WSE-00

Exxact - Connected Multiwire Universal Rotary Dimmer LED

– Max Brightness - Drag the slider bar to restrict the maximum brightness

NOTE: The maximum brightness level should be greater than minimum brightness level.

TIP: If you set the maximum brightness to the left most position on this slider bar, then the load glows at this maximum brightness value even when you drag the sliding bar in the control panel to the top most position (for more information refer to

control panel, page 15

).

B

Dimming Range

Minimum Brightness

Maximum Brightness

Note: The dimming range is limited if the min and max levels are too close to each other

Close

NOTE: The Dimming range is limited if the min. and max. levels are too close to each other.

LED indicator mode

You can select the LED indicator mode for easy identification of the device status.

Tap LED Indicator Mode (C) and select any one of the following:

– Reverse With Load - The LED on the Dimmer is On when the device is Off

– Consistent With Load - The LED on the Dimmer is On when the device is On

– Always Off - The LED on the Dimmer is always Off

– Always On - The LED on the Dimmer is always On

C

LED Indicator Mode

Reverse with Load

Consistent with Load

Always On

Cancel

For information on LED color during each modes, refer to

LED indication, page 25

.

DUG_Exxact MW Rotary Dimmer_WSE-00 13

Exxact - Connected Multiwire Universal Rotary Dimmer LED

Toggle mode setting

Using this setting, the device will remember the last state of the device.

Tap Toggle Mode Setting (D) and select any one of the following:

– 100% - The load glows at maximum brightness every time it is turned On

– Last Level (Memory Function) - The load glows at the previously set brightness level every time it is turned On

D

Toggle Mode Settings

100%

Last Level

Cancel

Removing the device

Using the Wiser app, you can remove a device from the device list.

Follow the steps to remove the device:

1. On the Home page, tap All devices > Rotary Dimmer .

2. Tap icon to display more details.

3. Tap Remove and Factory Reset Device (A).

More

Rotary Dimmer

A

TIP: Alternatively, you can long tap on the Rotary Dimmer on the Home page to remove the device.

NOTE: By removing the device, you will reset the device. If you still have a problem with the reset, then refer to

reset the device, page 15 .

14 DUG_Exxact MW Rotary Dimmer_WSE-00

Exxact - Connected Multiwire Universal Rotary Dimmer LED

Resetting the device

You can reset the dimmer to factory default manually.

Remove the knob and short-press the push button 3 times (<0.5 s) and then longpress the push button once (>10 s).

The LED blinks red after 10 s, and then release the push button.

Upon successful reset, the LED stops blinking. Then, the dimmer restarts and blinks green for a few seconds.

NOTE: After reset, the LED turns amber indicating that it is ready for pairing.

3× < 0,5 s

+1× > 10 s

Using the device

The Control Panel allows you to switch the device On/Off, increase/decrease the brightness and control various settings.

On the Home page, tap All devices > Rotary Dimmer to access the control panel.

On the control panel page, you can see the following:

• The current state of the device (A)

• The current brightness percentage (B)

• Sliding bar to adjust the brightness (C)

Schedule, page 17

(D)

Settings, page 12

(E)

Rotary Dimmer

A

B

D

E

On

100%

C

DUG_Exxact MW Rotary Dimmer_WSE-00 15

Exxact - Connected Multiwire Universal Rotary Dimmer LED

Switching/Dimming the device manually

You can manually switch the dimmer on/off and adjust its brightness level. This will provide power to the load connected to it.

To turn on or off the dimmer, short-press the push button (< 0,5 s).

< 0,5 s

To increase brightness, turn the dimmer knob clockwise, and to decrease brightness, turn it anti-clockwise.

Switching/Dimming the device using app

Using the Wiser app, you can switch On/Off and increase/decrease the brightness of the device.

Switch On/Off the device

Follow the steps to switch On/Off the device:

1. On the Home page, tap the power button (A) to switch On/Off the Rotary

Dimmer.

My Home

• • •

A

Rotary Dimmer

16

2. Alternatively, you can navigate to the

control panel, page 15

of the device and tap icon to switch On/Off the Rotary Dimmer.

NOTE: The control panel shows the current state of the Dimmer.

DUG_Exxact MW Rotary Dimmer_WSE-00

Exxact - Connected Multiwire Universal Rotary Dimmer LED

Adjusting the brightness of the device

Follow the steps to increase/decrease the brightness of the device:

1. On the Home page, tap the ˅ icon and drag the slider to adjust the brightness of the Dimmer.

• • •

Brightness

100%

2. Alternatively, you can navigate to the

control panel, page 15

of the device and drag the sliding bar up/down to increase/decrease the brightness.

NOTE: The control panel shows the current brightness percentage of the

Dimmer.

Creating a schedule

The Rotary Dimmer can be controlled and triggered by a schedule. Once the schedule is set, your system will follow the active schedule. You can create or modify the schedules at any time.

Follow the steps to create a schedule:

1. On the Home page, tap All devices > Rotary Dimmer .

2. Tap Schedule > Add schedule to add a schedule.

3. Set the time (A).

4. Tap Repeat (B) to select the days you want to set the schedule.

5. Tap Note (C), enter the note and tap Confirm .

6. Tap the toggle switch (D) to turn On the Notification for the schedule. The app will send a notification that the scheduled task is executed at the time of schedule.

7. Adjust the Brightness settings (E) through slide bar.

B

C

D

Note

Cancel Add Schedule

16

17

18 00

19 01

20

21

02

03

Save

Once

A

50%

100%

E

8. Tap Save .

DUG_Exxact MW Rotary Dimmer_WSE-00 17

Exxact - Connected Multiwire Universal Rotary Dimmer LED

Creating a moment

A Moment allows you to group multiple actions that are usually done together.

Using the Wiser app, you can create moments based on your needs (such as movie night).

Follow the steps to create a moment:

1. On the Home page, tap icon.

2. Go to Moment > + icon to create a moment.

3. Tap Edit name , enter the name of the moment (A) and tap Save .

TIP : You can choose the cover image that represents your moment by tapping icon.

Edit Name

A

Edit Name

Cancel Save

4. In the Action section, tap Add task (B) to open the slide-up menu.

5. In the Add task menu, you can do either or all of the following actions (C):

– Run the device - Select the devices that you want in a moment.

– Select Automation - Select the automation that you want to enable or disable. For more info refer to

Automation, page 20 .

– Delay - Set the delay time.

NOTE : You can add one or more actions using icon.

Edit Name

B

Add task

C

18 DUG_Exxact MW Rotary Dimmer_WSE-00

Exxact - Connected Multiwire Universal Rotary Dimmer LED

6. Tap Run the device > Rotary Dimmer and select either or both the functions to add in the moment:

– Rotary Dimmer - Turn the Dimmer On/Off (D)

– Brightness - Adjust the brightness level (E)

Select Function Next

D

E

7. Once all the actions are set, tap Save .

Cancel Moment Settings Save

My Settings

Action (1/80)

Show on Home Page

Editing a moment

Follow the steps to edit a moment:

1. On the Moment tab, locate the moment you want to edit and tap icon.

2. On the Edit page, you can tap each item (such as dimmer, shutter, delay, etc.) to change the settings and tap Save .

Cancel

My Settings

Edit Save

Action (1/80)

Show on Home Page

Delete

DUG_Exxact MW Rotary Dimmer_WSE-00 19

Exxact - Connected Multiwire Universal Rotary Dimmer LED

Deleting a moment

Follow the steps to delete a moment:

1. On the Moment tab, locate the moment that you want to delete and tap icon.

2. Tap Delete (A).

Cancel

My Settings

Edit Save

Action (1/80)

Show on Home Page

Delete

A

Creating an automation

An automation allows you to group multiple actions that are usually done together, triggered automatically or at scheduled times. By using the Wiser app, you can create automations based on your needs.

Follow the steps to create an automation:

1. On the Home page, tap the icon.

2. Go to Automation > + icon to create an automation.

3. Tap Edit name , enter the name of the automation (A) and tap Save .

TIP : You can choose the cover image that represents your automation by tapping icon.

My Automation

A

Edit Name

Cancel Save

20 DUG_Exxact MW Rotary Dimmer_WSE-00

Exxact - Connected Multiwire Universal Rotary Dimmer LED

4. Tap Any condition is met to select any one of the condition type (B):

– All conditions are met - The automation is triggered when all the conditions are met

– Any condition is met - The automation is triggered when at least one condition is met

My Automation

B

Select Condition type

All Conditions are met

Any condition is met

Cancel

5. Tap Add Condition to open the slide-up menu.

6. In the Add Condition menu, you can do either or all of the following options

(C):

– When weather changes - Select the various weather settings

– Schedule - Set the time and day

– When device status changes - Select the device and it’s function

NOTE: You can add one or more conditions using icon.

My Automation

C

Add Condition

When weather changes

Schedule

When device status changes

DUG_Exxact MW Rotary Dimmer_WSE-00 21

22

Exxact - Connected Multiwire Universal Rotary Dimmer LED

7. Tap When device status changes > Rotary Dimmer and select either or both the functions:

– Rotary Dimmer - Turn the Dimmer On/Off (D)

– Brightness - Adjust the brightness level (E)

Select Function Next

D

E

8. Tap Add task to open the slide-up menu.

9. In the Add task menu, you can do either or all of the following options (F):

– Run the device - Select the devices that you want to be triggered

– Moment or Automation - Select the moment which you want to trigger or select the automation that you want to enable or disable

– Send notification - Turn On notification for the automation

– Delay - Set the delay time

NOTE : You can add one or more actions using icon.

My Automation

Add Task

Add task

F

DUG_Exxact MW Rotary Dimmer_WSE-00

Exxact - Connected Multiwire Universal Rotary Dimmer LED

10. Tap on Effective period to set the time range for the automation. You can select any one of the following (G):

– All-day - 24 hours

– Daytime - From sunrise to sunset

– Night - From sunset to sunrise

– Custom - User defined time period

Eff ective Period Next

City

Eff ective period

G

All-day

24 hours

Daytime

From sunrise to sunset

Night

From sunset to sunrise

Custom

User-defi ned time period

Block 3 Harbor Layout

Repeat Everyday

11. Once all the actions and conditions are set, tap Save .

Once the automation is saved, it is visible on the Automation tab. You can tap the toggle switch on the automation to enable it.

Example of an automation

This demonstration shows you how to create an automation to switch On the light when a window door sensor is activated at night.

NOTE: The Dimmer will not be switched Off automatically when the sensor sends the "Closed" message. To switch Off the dimmer when the door is closed, you must create a new automation.

1. Go to Automation > + icon to create an automation.

2. Tap Edit name , enter the name of the automation and tap Save .

TIP : You can choose the cover image that represents your automation by tapping icon.

3. Tap Add Condition > When device status changes > Window Door

Sensor .

4. Tap Window Door Sensor > Open (A).

A

Open

Closed

Window Door Sensor

5. Tap Add task > Run the device > Rotary Dimmer .

DUG_Exxact MW Rotary Dimmer_WSE-00 23

Exxact - Connected Multiwire Universal Rotary Dimmer LED

6. Tap Rotary Dimmer (B) and tap On in the slide-up menu.

B

On

Off

Rotary Dimmer

Save Cancel

7. Tap Effective period , select Night and tap Next .

8. In the Automation Settings page, tap Save .

Cancel Automation Settings Save

My Automation

Any condition is met

Window Door Sensor

Window Door Sensor:Open

(1/10)

Action

Rotary Dimmer

(1/80)

Rotary Dimmer:On

Eff ective Period Night

Once the automation is saved, it is visible on the Automation tab. You can tap the toggle switch on the automation to enable it.

Editing an automation

Follow the steps to edit an automation:

1. On the Automation tab, locate the automation you want to edit and tap icon.

2. On the Edit page, you can tap each item (such as dimmer, shutter, delay, etc.) to change the settings and tap Save .

Cancel Edit

My Automation

Save

Any Condition Is Met

Action

(1/10)

(1/80)

All-Day

Delete

24 DUG_Exxact MW Rotary Dimmer_WSE-00

Exxact - Connected Multiwire Universal Rotary Dimmer LED

Deleting an automation

Follow the steps to delete an automation:

1. On the Automation tab, locate the automation you want to delete and tap icon.

2. Tap Delete (A).

Cancel Edit

My Automation

Save

Any Condition Is Met

Action

(1/10)

(1/80)

Delete

All-Day

A

LED Indication

Pairing

User Action

Press the push-button 3 times

LED Indication

LED blinks amber per second.

Resetting

User Action

Press the push-button 3 times and hold it down once for > 10 s.

LED Indication

After 10 s, the LED blinks red.

Status

Pairing mode is active for 30 seconds.

When pairing is completed, LED glows green for some time before turning Off.

Status

The device is in reset mode. It is reset to the factory settings after 10 seconds. The device then restarts and the LED blinks green for a few seconds and then stays amber.

LED Indicator Mode/Backlight Mode

Load Status ON

Reverse with load No LED

Consistent with load

Always Off

Always On

No LED

OFF

No LED

No LED

DUG_Exxact MW Rotary Dimmer_WSE-00 25

Exxact - Connected Multiwire Universal Rotary Dimmer LED

Troubleshooting

Symptom

Dimming up not possible.

Switching On not possible.

Flickering at minimum brightness.

Flickering

Only slight dimming capability

The device is not ready to pair after the device is removed from the app.

Solution

• Reduce/increase load.

• Allow the Dimmer to cool in case of overheating.

• Change the load (if the load is incompatible with the Dimmer).

• Allow the Dimmer to cool in case of overheating.

• Reduce load.

• Change load.

• Check electrical connections.

• Increase minimum brightness (if flickering still persists, install a 31LCDA load correction device).

• Change the load (if the minimum brightness is insufficient).

• Set to RL LED mode.

• Change load.

• Set to RL LED mode.

• Change dimming range.

• Change the load (if the load is incompatible with the Dimmer).

• Set to RL LED mode.

Reset to factory default settings, refer to

resetting the device, page 15 .

Technical Data

Nominal power

Load type

LED

Load name

Incandescent lamp

Halogen lamp

2 wire (without neutral)

7–130 W (max. 0,8 A)

RC

Load value

3 wire (with neutral)

0–130 W (max. 0,8 A)

RC

7–80 W (max. 0,5 A)

RL

0–80 W (max. 0,5 A)

RL

14–200 W

R

0–200 W

R

14–150 W

R

0–150 W

R

Nominal voltage

Standby

Connecting terminals

Neutral conductor

Ambient temperature

Storage temperature

Transport temperature

26

Iron core transformer

Electronic step-down converter

14–150 VA

RL

14–150 VA

RC

0–150 VA

RL

0–150 VA

RC

AC 230 V ~, 50 Hz

Max 0.4 W

Screw terminals for max. 2 x 2.5 mm², 0.5 Nm

Recommended

5 to 25 °C (temporarily up to 35 °C)

-25 °C to 70 °C

-25 °C to 70 °C

DUG_Exxact MW Rotary Dimmer_WSE-00

Exxact - Connected Multiwire Universal Rotary Dimmer LED

Extension unit

Fuse protection

Device self–protection

Operating frequency

Max. Radio-frequency power transmitted

Communication protocol

Single push-button, unlimited number, max. 50 m

16 A circuit breaker

Thermal protection

Overload-resistant

Short-circuit protection

2405 - 2480 MHz

< 10 mW

Zigbee 3.0 certified

DUG_Exxact MW Rotary Dimmer_WSE-00 27

Compliance

Compliance information for Green Premium products

Find and download comprehensive information about Green Premium products, including RoHS compliance and REACH declarations as well as Product

Environmental Profile (PEP) and End-of-Life instructions (EOLI).

General information about Green Premium products

Click the link below to read about Schneider Electric’s Green Premium product strategy.

https://www.schneider-electric.com/en/work/support/green-premium/

Find compliance information for a Green Premium product

Click the link below to search for a product’s compliance information (RoHS, REACH,

PEP and EOLI).

NOTE: You will need the product reference number or product range to perform the search.

https://www.reach.schneider-electric.com/CheckProduct.aspx?cskey= ot7n66yt63o1xblflyfj

Trademarks

This guide makes reference to system and brand names that are trademarks of their relevant owners.

• Zigbee ® is a registered trademark of the Connectivity Standards Alliance.

• Apple ® and App Store ® are brand names or registered trademarks of Apple Inc.

• Google Play™ Store and Android™ are brand names or registered trademarks of Google Inc.

• Wi-Fi ® is a registered trademark of Wi-Fi Alliance ® .

• Wiser™ is a trademark and the property of Schneider Electric, its subsidiaries and affiliated companies.

Other brands and registered trademarks are the property of their respective owners.

Schneider Electric

35 rue Joseph Monier

92500 Rueil Malmaison

France

+ 33 (0) 1 41 29 70 00 www.se.com

As standards, specifications, and design change from time to time, please ask for confirmation of the information given in this publication.

© 2022 – Schneider Electric . All rights reserved.

DUG_Exxact MW Rotary Dimmer_WSE-00

advertisement

Related manuals