Schneider Electric Exxact User Guide

Exxact - Connected Motion Sensor with
Multiwire Dimmer
Device user guide
Information about features and functionality of the devices
08/2022
www.se.com
Legal Information
The Schneider Electric brand and any trademarks of Schneider Electric SE and its
subsidiaries referred to in this guide are the property of Schneider Electric SE or its
subsidiaries. All other brands may be trademarks of their respective owners.
This guide and its content are protected under applicable copyright laws and
furnished for informational use only. No part of this guide may be reproduced or
transmitted in any form or by any means (electronic, mechanical, photocopying,
recording, or otherwise), for any purpose, without the prior written permission of
Schneider Electric.
Schneider Electric does not grant any right or license for commercial use of the guide
or its content, except for a non-exclusive and personal license to consult it on an "as
is" basis. Schneider Electric products and equipment should be installed, operated,
serviced, and maintained only by qualified personnel.
As standards, specifications, and designs change from time to time, information
contained in this guide may be subject to change without notice.
To the extent permitted by applicable law, no responsibility or liability is assumed by
Schneider Electric and its subsidiaries for any errors or omissions in the informational
content of this material or consequences arising out of or resulting from the use of the
information contained herein.
Table of Contents
Safety information .......................................................................................5
Exxact - Connected Motion Sensor with Multiwire Dimmer ..................6
For your safety ...........................................................................................6
About the device.........................................................................................7
Installing the device ....................................................................................7
Pairing the device .......................................................................................7
Pairing device manually.........................................................................7
Pairing device with auto scan.................................................................9
Checking the type of wiring mode ..............................................................10
Configuring the device ..............................................................................10
Changing the device icon ....................................................................10
Renaming the device .......................................................................... 11
Changing the device location ............................................................... 11
Managing motion sensor dimmer settings .............................................12
Removing the device ................................................................................15
Resetting the device .................................................................................16
Using the device.......................................................................................16
Switching/Dimming the device manually ...............................................16
Switching/Dimming the device using app ..............................................17
Creating a schedule ............................................................................18
Creating a moment .............................................................................19
Creating an automation .......................................................................21
LED Indication..........................................................................................26
Troubleshooting .......................................................................................27
Technical Data .........................................................................................27
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
3
Safety information
Safety information
Important information
Read these instructions carefully and look at the equipment to become familiar
with the device before trying to install, operate, service, or maintain it. The
following special messages may appear throughout this manual or on the
equipment to warn of potential hazards or to call attention to information that
clarifies or simplifies a procedure.
The addition of either symbol to a “Danger” or “Warning” safety label indicates
that an electrical hazard exists which will result in personal injury if the
instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that accompany this symbol to avoid possible
injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in
death or serious injury.
Failure to follow these instructions will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result
in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to physical injury.
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
5
Exxact - Connected Motion Sensor with Multiwire Dimmer
Exxact - Connected Motion Sensor with Multiwire
Dimmer
WDE00X962
For your safety
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Safe electrical installation must be carried out only by skilled professionals.
Skilled professionals must prove profound knowledge in the following areas:
- Connecting to installation networks.
- Connecting several electrical devices.
- Laying electric cables.
- Safety standards, local wiring rules and regulations.
Failure to follow these instructions will result in death or serious injury.
DANGER
RISK OF FATAL INJURY FROM ELECTRIC SHOCK
The output may carry electric current even when the load is switched Off.
Disconnect the device from the supply by means of the fuse in the incoming
circuit before working on the device.
Failure to follow these instructions will result in death or serious injury.
CAUTION
THE DEVICE MAY BE DAMAGED
Only connect dimmable load.
Failure to follow these instructions can result in injury or equipment
damage.
6
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
Exxact - Connected Motion Sensor with Multiwire Dimmer
About the device
The Connected Motion Sensor with Multiwire Dimmer (hereinafter referred to as
Motion sensor dimmer) detects moving heat sources (e.g. persons) and can dim
ohmic, inductive or capacitive loads and switch them on for a settable overtravel
time. It can detect the load automatically and provides thermal protection,
overload-resistance and short-circuit protection.
Control options
Home control: To control the motion sensor through the Wiser app you will need
the Wiser Gateway.
Direct operation: The motion sensor can always be controlled directly on-site.
You can also connect any number of mechanical push-buttons to control the
device.
Installing the device
Refer to the installation instruction supplied with this product.
See Connected Motion Sensor with Multiwire Dimmer.
Pairing the device
Using the Wiser app, pair your device with the Gateway to access and control the
device. You can either add the device manually or do an auto-scan to pair it.
Pairing device manually
Follow the steps to pair the device manually:
1. On Home page, tap + icon.
2. Tap
icon and select the Wiser Hub.
3. Select any one of the options to add device (A):
– Add Device with Install Code
– Add Device without Install Code
Add Device
Install Code is Recommended
To enhance network security, we strongly
recommend using Install Code to add a
device.
If you are unable to scan or type the Install
Code, you can still add the device without it.
Add Device with Install Code
A
Add Device without Install Code
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
7
Exxact - Connected Motion Sensor with Multiwire Dimmer
4. To add the device with Install Code, tap Add Device with Install Code button
to open the slide-up menu. Select any one of the options (B):
– Scan Install Code - You can scan the device for the Install Code
– Enter Install Code Manually - You can manually enter the install code from
the device
After adding the device with Install Code, proceed to Step 6.
Add Device
Install Code is Recommended
To enhance network security, we strongly
recommend using Install Code to add a
device.
If you are unable to scan or type the Install
Code, you can still add the device without it.
Add Device with Install Code
Add Device
Install Code
Scanwithout
Install Code
Enter Install Code Manually
B
Cancel
TIP: It is highly recommended to add the device with Install code.
5. To add the device without Install Code, tap Add Device without Install
Code.
6. Short press the push button 3 times (< 0,5 s) on the device.
3× < 0,5 s
The LED blinks amber.
7. In the app, select Confirm LED is blinking amber and tap Start
configuration (C).
Cancel
How to pair device
2
1
x3
C
The app displays the progress of connecting the device.
8
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
Exxact - Connected Motion Sensor with Multiwire Dimmer
8. Wait for a few seconds until the device is connected and the app shows that
the device is added successfully.
The solid green LED on the motion sensor dimmer shows that it is
successfully connected to the Gateway.
9. After the device is added in the app, tap Done.
Pairing device with auto scan
Pairing the device with auto scan automatically discovers the device when the
corresponding device is powered on.
Follow the steps to pair the device:
1. On the Home page, tap + icon.
2. Tap Auto scan tab and tap Confirm.
3. If you have multiple hubs, do Step 4 or proceed to Step 5.
4. Tap Select hub and select the Wiser hub from the slide-up menu.
5. Short press the push button 3 times (< 0,5 s).
NOTE:
•
The LED blinks amber.
•
Wait for a few seconds until the device search is complete.
6. Tap Motion Sensor Dimmer and tap Next (A).
Add Manually
Auto Scan
Available devices found
Motion Sensor
Dimmer
Next
A
7. Once the device is added successfully, tap Done.
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
9
Exxact - Connected Motion Sensor with Multiwire Dimmer
Checking the type of wiring mode
Using the Wiser app, you can check whether the dimmer is connected with or
without neutral wire.
Follow the steps to check the type of wiring mode:
1. On the Home page, tap All devices > Motion Sensor Dimmer.
2. Tap
icon and tap Device information.
You see the type of wiring mode (A) in the app.
Virtual ID: bf9019d2978aac84f0ajay
copy
MAC Address: 680AE2FFFE1179AD
A
Wiring Mode: With neutral wire
NOTE: Virtual ID and MAC address may vary with the device.
Configuring the device
Changing the device icon
Using the Wiser app, you can change the icon of the device.
Follow the steps to change the device icon:
1. On the Home page, tap All devices > Motion Sensor Dimmer.
2. Tap
icon and tap
.
3. Tap Icon to view the menu.
4. In the slide-up menu, select any one of the following (A):
– Take photo - Allows you to take a photo from the mobile camera
– Select from Icon Library - Allows you to select an icon from the app library
– Select from Album - Allows you to select photo from the mobile gallery
Icon
Name
Motion Dimmer
LK Home
Location
Take photo
Select from Icon Library
A
Select from album
Cancel
10
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
Exxact - Connected Motion Sensor with Multiwire Dimmer
5. Tap on the required photo/icon to change the icon.
Renaming the device
Using the Wiser app, you can rename your device for easy identification.
Follow the steps to rename the device:
1. On the Home page, tap All devices > Motion Sensor Dimmer.
2. Tap
icon and tap
.
3. Tap Name, enter the name (A) and tap Save.
Rename
Icon
A
Motion Dimmer
Name
Location Cancel
Save
Changing the device location
Using the Wiser app, you can change the location of the device.
Follow the steps to change the device location:
1. On the Home page, tap All devices > Motion Sensor Dimmer.
2. Tap
icon and tap
.
3. Tap Location, select any location from the list (A) and tap Save.
Device location
Save
A
Kitchen
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
11
Exxact - Connected Motion Sensor with Multiwire Dimmer
Managing motion sensor dimmer settings
Using The Wiser app, you can manage the settings.
Follow the steps to access the motion sensor dimmer settings:
1. On the Home page, tap All devices > Motion Sensor Dimmer.
2. On the device control panel page, tap Settings.
Dimmer setting
Dimming Mode
You can change the dimming mode in the app if you have problems with light
flickering. This improves the dimming quality.
Tap Dimming Mode and select either of the following (A):
– Auto - When any other load is connected to the dimmer (e.g. filament bulb).
– RL-LED - Select the mode only when the LED is not working properly in Auto
mode.
NOTE: Refer to technical data, page 27 for more information.
Settings
Dimmer Settings
Dimming Mode
Auto
Dimming Range
Toggle Mode Setting
Last Level
Sensor Settings
Sensitivity Setting
High
Detection Delay
05:00
Lux Settings
Lux Level
60 lux
Dimming Mode
Lux Threshold
Auto
1022 lux
A
Leading Edge
Cancel
Dimming Range
You can restrict the maximum and minimum brightness of the load connected to
the device. This is done to avoid flickering and switching off the LED.
Tap Dimming Range and do either or both of the following (B):
– Min Brightness - Drag the slider bar to restrict the minimum brightness.
NOTE: The minimum brightness level should be lower than maximum
brightness level.
TIP: If you set the minimum brightness to the right most position on this slider
bar, then the load glows at this minimum brightness value even when you drag
the sliding bar in the control panel to the bottom most position (for more
information refer to control panel, page 16).
12
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
Exxact - Connected Motion Sensor with Multiwire Dimmer
– Max Brightness - Drag the slider bar to restrict the maximum brightness.
NOTE: The maximum brightness level should be greater than minimum
brightness level.
TIP: If you set the maximum brightness to the left most position on this slider
bar, then the load glows at this maximum brightness value even when you
drag the sliding bar in the control panel to the top most position (for more
information refer to control panel, page 16).
Settings
Dimmer Settings
Dimming Mode
Auto
Dimming Range
Toggle Mode Setting
Last Level
Sensor Settings
Sensitivity Settings
High
Detection Delay
Dimming
Lux
Settings
05:00
Range Setting
Lux Level
60 lux
Min
Brightness
Lux
Threshold
Lux Customization
Max Brightness
1022 lux
B
Note - The dimming range is limited if the min and max
levels are too close to each other.
Close
NOTE: The Dimming range is limited if the min. and max. levels are too close
to each other.
Toggle mode setting
Using this setting, the device will remember the last state of the device.
Tap Toggle Mode Setting and select any one of the following (C):
– 100% - The load glows at maximum brightness every time it is turned On.
– Last Level (Memory Function) - The load glows at the previously set brightness
level every time it is turned On.
Settings
Dimmer Settings
Dimming Mode
Auto
Dimming Range
Toggle Mode Setting
Last Level
Sensor Settings
Sensitivity Setting
High
Detection Delay
05:00
Lux Settings
Lux Level
Lux Threshold
60 lux
Toggle Mode Setting
1022 lux
100%
C
Last Level
Cancel
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
13
Exxact - Connected Motion Sensor with Multiwire Dimmer
Sensor setting
Sensitivity Setting
Using the Wiser app, you can set the sensitivity of the sensor (such as High,
Medium, Low).
Tap Sensitivity Setting and select one of the following levels (A):
•
High
•
Medium
•
Low
NOTE: The high sensitivity level detects the slightest movement.
Settings
Dimmer Settings
Dimming Mode
Auto
Dimming Range
Toggle Mode Setting
Last Level
Sensor Settings
Sensitivity Setting
High
Detection Delay
05:00
Lux Settings
Lux Level
60 lux
Sensitivity Setting
Lux Threshold
High
1022 lux
Medium
A
Cancel
Detection Delay
Using the wiser app, you can set the detection delay time.
Tap Detection Delay and select the time duration (B) or tap Detection delay
custom (C) to customize your detection delay time.
Settings
Dimmer Settings
Dimming Mode
Auto
Dimming Range
Toggle Mode Setting
Last Level
Sensor Settings
Sensitivity Setting
High
Detection Delay
Detection Delay
05:00
Lux Settings
15 Sec
Lux Level
60 lux
30 Sec
B
Lux Threshold
45 Sec
1022 lux
1 Min
Detection Delay Custom
C
Cancel
14
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
Exxact - Connected Motion Sensor with Multiwire Dimmer
Lux Customization
Using the Wiser app, you can define the threshold value for lux ranges (such as
very dark, dark, bright, very bright) of the environment. This will help to prevent the
false alarm caused by changes in the light intensity.
Tap Lux Customization and drag the slider bar (D) to define its threshold value
and tap Save.
•
Very dark level - Lux value ranges from 1 lux to 100 lux
•
Dark level - Lux level ranges from 6 lux to 300 lux
•
Bright level - Lux level ranges from 101 lux to 2000 lux
NOTE: The Current Lux Value is the current light level present in the
environment measured by the sensor.
Settings
Dimmer Settings
Dimming Mode
Auto
Dimming Range
Toggle Mode Setting
Last Level
Sensor Settings
Sensitivity Setting
High
Detection Delay
05:00
Lux Settings
Lux Level
60 lux
Lux value : 1022
Lux Threshold
1 lux
250 lux
500 lux
750 lux
1000lux
lux
1022
A
Use Current Lux Value
Cancel
Removing the device
Using the Wiser app, you can remove a device from the device list.
Follow the steps to remove the device:
1. On the Home page, tap All devices > Motion Sensor Dimmer.
2. Tap
icon to display more details.
3. Tap Remove and Factory Reset Device (A).
More
Motion Dimmer
Room: LK Home
Device information
Moment and Automation
Others
FAQ & Feedback
Add to home Screen
No updates available.
Remove and Factory Reset Device
A
TIP: Alternatively, you can long tap on the Motion Sensor Dimmer on
the Home page to remove the device.
NOTE: By removing the device, you will reset the device. If you still have
a problem with the reset, then refer to reset the device, page 16.
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
15
Exxact - Connected Motion Sensor with Multiwire Dimmer
Resetting the device
You can reset the device to factory default manually.
Follow the steps to reset the device:
1. Short press push button 3 times (< 0.5 s) and then long press the push button
once (>10 s).
2. After 10 s, LED starts blinking red then release the push button.
The LED stops blinking upon successful reset of the device.
3. The Motion Sensor Dimmer restarts and blinks green for a few seconds.
NOTE: After reset, the LED turns amber.
3× < 0,5 s
+1× > 10 s
Using the device
The Control Panel allows you to switch the device On/Off, increase/decrease the
brightness and control various settings.
On the Home page, tap All devices > Motion Sensor Dimmer to access the
control panel.
On the control panel page, you can see the following:
•
The motion detection and current Lux level (A)
•
The current device state and brightness level (B)
•
Sliding bar to adjust the brightness (C)
•
Schedule, page 18 (D)
•
Settings, page 12 (E)
Motion Dimmer
A
60 lux
B
On 50%
C
D
E
Schedule
Settings
Switching/Dimming the device manually
You can switch On/Off and increase/decrease the brightness of the Dimmer
manually. The Dimmer will provide power to the load connected to it.
Short press the push button on the device once to switch On/Off the Motion
Sensor Dimmer.
16
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
Exxact - Connected Motion Sensor with Multiwire Dimmer
< 0,5 s
Long press the push button on the device to increase/decrease the brightness of
the Dimmer.
< 0,5 s
Switching/Dimming the device using app
Using the Wiser app, you can switch On/Off and increase/decrease the brightness
of the device.
Follow the steps to switch the device On/Off:
1. On the Home page, tap the power button (A) to switch On/Off the Motion
Sensor Dimmer.
My Home
All Devices
Tuya Demo
Living Room
•••
A
Motion Sensor Dimmer
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
17
Exxact - Connected Motion Sensor with Multiwire Dimmer
2. On the Home page, tap the ˅ icon and drag the slider (B) to adjust the
brightness of the dimmer.
My Home
All Devices
Tuya Demo
Living Room
•••
Motion Dimmer
Brightness
50%
B
3. Alternatively, you can navigate to the control panel, page 16 of the device and
tap
icon to switch On/Off the and use the slider to adjust the brightness of
Motion Sensor Dimmer.
NOTE: The control panel shows the current state of the device.
Creating a schedule
The Motion Sensor Dimmer can be controlled and triggered by a schedule. Once
the schedule is set, your system will follow the active schedule. You can create or
modify the schedules at any time.
Follow the steps to create a schedule:
1. On the Home page, tap All devices > Motion Sensor Dimmer.
2. Tap Schedule > Add schedule to add a schedule.
3. Set the time (A).
4. Tap Repeat (B) to select the days you want to set the schedule.
5. Tap Note (C), enter the note and tap Confirm.
6. Tap the toggle switch (D) to turn On the Notification for the schedule. The
app will send a notification that the scheduled task is executed at the time of
schedule.
7. Adjust the Brightness settings (E) through slide bar.
Cancel
Add Schedule
Save
07
08
09
B
C
D
A
00
10
01
11
02
12
03
Repeat
Once
Note
Motion Dimmer
Brightness Setting 33%
50%
100%
E
8. Tap Save.
18
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
Exxact - Connected Motion Sensor with Multiwire Dimmer
Creating a moment
A Moment allows you to group multiple actions that are usually done together.
Using the Wiser app, you can create moments based on your needs (such as
movie night).
Follow the steps to create a moment:
1. On the Home page, tap
icon.
2. Go to Moment > + icon to create a moment.
3. Tap Edit name, enter the name of the moment (A) and tap Save.
TIP: You can choose the cover image that represents your moment by
icon.
tapping
Cancel
Moment Settings
Save
Edit Name
Action
(0/80)
Edit Name
A
Add Task
Cancel
Show on Home
Page
Save
4. In the Action section, tap Add task (B) to open the slide-up menu.
5. In the Add task menu, you can do either or all of the following actions (C):
– Run the device - Select the devices that you want in a moment.
– Select Automation - Select the automation that you want to enable or
disable. For more info refer to Automation, page 21.
– Delay - Set the delay time.
NOTE: You can add one or more actions using
Cancel
Moment Settings
icon.
Save
Edit Name
Action
Add Task
B
Show on Home Page
Add task
C
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
19
Exxact - Connected Motion Sensor with Multiwire Dimmer
6. Tap Run the device > Motion Sensor Dimmer to select either or all the
functions to add in the moment and tap Save:
– Motion Dimmer (D) : To set the device On/Off
– Brightness (E) :To set the percentage of brightness required.
Select Function
D
E
Next
Motion Dimmer
Brightness
7. Once all the actions are set, tap Save.
Cancel
Moment Settings
Save
My Settings
Action
(2/80)
Motion Dimmer
LK Home
Motion Dimmer
LK Home
Motion Dimmer:On
Brightness:50%
Show on Home Page
Editing a moment
Follow the steps to edit a moment:
1. On the Moment tab, locate the moment you want to edit and tap
icon.
2. On the Edit page, you can tap each item (such as dimmer, shutter, relay, etc.)
to change the settings and tap Save.
Edit
Cancel
Save
My Settings
Action
(2/80)
Motion Dimmer
LK Home
Motion Dimmer
LK Home
Motion Dimmer:On
Brightness:50%
Show on Home Page
Delete
20
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
Exxact - Connected Motion Sensor with Multiwire Dimmer
Deleting a moment
Follow the steps to delete a moment:
1. On the Moment tab, locate the moment that you want to delete and tap
icon.
2. Tap Delete (A).
Edit
Cancel
Save
My Settings
Action
(2/80)
Motion Dimmer
Motion Dimmer:On
LK Home
Motion Dimmer
Brightness:50%
LK Home
Show on Home Page
A
Delete
Creating an automation
An automation allows you to group multiple actions that are usually done together,
triggered automatically or at scheduled times. By using the Wiser app, you can
create automations based on your needs.
Follow the steps to create an automation:
1. On the Home page, tap the
icon.
2. Go to Automation > + icon to create an automation.
3. Tap Edit name, enter the name of the automation (A) and tap Save.
TIP: You can choose the cover image that represents your automation by
tapping
Cancel
icon.
Automation Settings
Save
My Automation
Any Condition Is Met
(0/10)
Edit Name
Add Condition
A
Action
(Added
Save 0/80)
Cancel
Add Task
All-Day
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
21
Exxact - Connected Motion Sensor with Multiwire Dimmer
4. Tap Any condition is met to select any one of the condition type (B):
– All conditions are met - The automation is triggered when all the conditions
are met
– Any condition is met - The automation is triggered when at least one
condition is met
Cancel
Automation Settings
Save
My Automation
Any Condition Is Met
(0/10)
Add Condition
(Added 0/80)
Action
Add Task
Select Condition type
All-Day
All Conditions are met
B
Any condition is met
Cancel
5. Tap Add Condition to open the slide-up menu.
6. In the Add Condition menu, you can do either or all of the following options
(C):
– When weather changes - Select the various weather settings
– Schedule - Set the time and day
– When device status changes - Select the device and it’s function
Note: You can add one or more conditions using
Cancel
Automation Settings
icon.
Save
My Automation
Any Condition Is Met
(0/10)
Add Condition
Action
Add Condition
(Added 0/80)
When weather changes
C
Add Task
Schedule
When device status changesAll-Day
22
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
Exxact - Connected Motion Sensor with Multiwire Dimmer
7. Tap When device status changes > Motion Sensor Dimmer and select
either functions:
– Motion Dimmer - To set the dimmer On\Off (D)
– Motion State - Select the Occupy or Unoccupied state (E)
– Lux Level - Adjust the desired Lux Level (F)
– Brightness - Adjust the desired brightness level (G)
Select Function
D
E
F
G
Motion Dimmer
Motion State
Lux Level
Brightness
8. Tap Add task to open the slide-up menu.
9. In the Add task menu, you can do either or all of the following options (H):
– Run the device - Select the devices that you want to be triggered
– Moment or Automation - Select the moment which you want to trigger or
select the automation that you want to enable or disable
– Send notification - Turn On notification for the automation
– Delay - Set the delay time
NOTE: You can add one or more actions using
Cancel
Automation Settings
icon.
Save
My Automation
Any Condition Is Met
Add Condition
Action
Add Task
Add task
All-Day
H
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
23
Exxact - Connected Motion Sensor with Multiwire Dimmer
10. Tap on Effective period to set the time range for the automation. You can
select any one of the following (I):
– All-day - 24 hours
– Daytime - From sunrise to sunset
– Night - From sunset to sunrise
– Custom - User defined time period
Next
City
24 hours
From sunrise to sunset
I
From sunset to sunrise
Custom
Repeat
11. Once all the actions and conditions are set, tap Save.
Once the automation is saved, it is visible on the Automation tab. You can
tap the toggle switch on the automation to enable it.
Example of an automation
This demonstration shows you how to create an automation to get notification on
your app when the motion is detected.
1. Go to Automation > + icon to create an automation.
2. Tap Edit name, enter the name of the automation and tap Save.
TIP: You can choose the cover image that represents your automation by
tapping
icon.
3. Tap Add Condition > When device status changes > Motion Sensor
Dimmer.
4. In Select function menu tap on Motion State > Occupied (A).
Motion State
A
Occupied
Unoccupied
24
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
Exxact - Connected Motion Sensor with Multiwire Dimmer
5. Tap Add task > Send Notification and select Notifications (B).
Next
B
6. Tap Next.
7. In the Automation Settings page, tap Save.
Cancel
Automation Settings
Save
My Automation
Any Condition Is Met
(1/10)
Motion Dimmer
Motion State: Occupied
Action
(1/80)
On
All-Day
Once the automation is saved, it is visible on the Automation tab. You can
tap the toggle switch on the automation to enable it.
Push notification will appear on the screen when the automation is triggered. You
can also tap on
icon to access the notification history.
Editing an automation
Follow the steps to edit an automation:
1. On the Automation tab, locate the automation you want to edit and tap
icon.
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
25
Exxact - Connected Motion Sensor with Multiwire Dimmer
2. On the Edit page, you can tap each item (such as dimmer, shutter, relay, etc.)
to change the settings and tap Save.
Edit
Cancel
Save
My Settings
Any Condition Is Met
(2/10)
Motion Dimmer
Motion Dimmer: On
Motion Dimmer
Motion State: Occupied
Action
(1/80)
Motion Dimmer
LK Home
Brightness:50%
All-Day
Delete
Deleting an automation
Follow the steps to delete an automation:
1. On the Automation tab, locate the automation you want to delete and tap
icon.
2. Tap Delete (A).
Edit
Cancel
Save
My Settings
Any Condition Is Met
(2/10)
Motion Dimmer
Motion Dimmer: On
Motion Dimmer
Motion State: Occupied
Action
(1/80)
Motion Dimmer
LK Home
Brightness:50%
All-Day
Delete
A
LED Indication
Pairing
User Action
LED Indication
Status
Press the push button 3 times
LED blinks amber per second.
Pairing mode is active for 30 seconds.
When pairing is completed, LED glows
green for some time before turning Off.
User Action
LED Indication
Status
Press the push button 3 times and hold it
down once for > 10 s.
After 10 s, the LED blinks red.
The device is in reset mode. It is reset to the
factory settings after 10 seconds. The
device then restarts and the LED blinks
green for a few seconds and then stays
amber.
Resetting
26
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
Exxact - Connected Motion Sensor with Multiwire Dimmer
Troubleshooting
Symptom
Solution
Dimming up not possible.
Switching On not possible.
Flickering at minimum brightness.
Flickering
Only slight dimming capability
The device is not ready to pair after the device is
removed from the app.
•
Reduce/increase load.
•
Allow the Dimmer to cool in case of overheating.
•
Change the load (if the load is incompatible with the Dimmer).
•
Allow the Dimmer to cool in case of overheating.
•
Reduce load.
•
Change load.
•
Check wiring between the push button and the Dimmer.
•
Increase minimum brightness (if flickering still persists, install a 31LCDA load
correction device).
•
Change the load (if the minimum brightness is insufficient).
•
Set to RL LED mode.
•
Change load.
•
Set to RL LED mode.
•
Change dimming range.
•
Change the load (if the load is incompatible with the Dimmer).
•
Set to RL LED mode.
Reset to factory default settings, refer to reset the device, page 16.
Technical Data
Nominal power
Load value
Load type
Load name
LED
2 wire (without neutral)
7–130 W (max. 0,8 A)
7–80 W (max. 0,5 A)
Incandescent lamp
Halogen lamp
Iron core transformer
Electronic step-down converter
RC
RL
3 wire (with neutral)
0–130 W (max. 0,8 A)
0–80 W (max. 0,5 A)
14–200 W
R
0–200 W
R
14–150 W
R
0–150 W
R
14–150 VA
RL
0–150 VA
RL
14–150 VA
RC
0–150 VA
RC
Nominal voltage
AC 230 V ~, 50 Hz
Standby
Max 0.4 W
Connecting terminals
Screw terminals for max. 2 x 2.5 mm², 0.5 Nm
Neutral conductor
Recommended
Ambient temperature
5 to 25 °C (temporarily up to 35 °C)
Storage temperature
-25 °C to 70 °C
Transport temperature
-25 °C to 70 °C
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
RC
RL
27
Exxact - Connected Motion Sensor with Multiwire Dimmer
Extension unit
Single push-button, unlimited number, max. 50 m
Fuse protection
16 A circuit breaker
Device self–protection
Thermal protection
Overload-resistant
Short-circuit protection
Operating frequency
2405 - 2480 MHz
Max. Radio-frequency power transmitted
< 10 mW
Communication protocol
Zigbee 3.0 certified
28
DUG_Exxact Motion Sensor MW Dimmer_WSE-00
Compliance
Compliance information for Green Premium
products
Find and download comprehensive information about Green Premium products,
including RoHS compliance and REACH declarations as well as Product
Environmental Profile (PEP) and End-of-Life instructions (EOLI).
General information about Green Premium products
Click the link below to read about Schneider Electric’s Green Premium product
strategy.
https://www.schneider-electric.com/en/work/support/green-premium/
Find compliance information for a Green Premium product
Click the link below to search for a product’s compliance information (RoHS, REACH,
PEP and EOLI).
NOTE: You will need the product reference number or product range to perform
the search.
https://www.reach.schneider-electric.com/CheckProduct.aspx?cskey=
ot7n66yt63o1xblflyfj
Trademarks
This guide makes reference to system and brand names that are trademarks of their
relevant owners.
•
Zigbee® is a registered trademark of the Connectivity Standards Alliance.
•
Apple® and App Store® are brand names or registered trademarks of Apple Inc.
•
Google Play™ Store and Android™ are brand names or registered trademarks
of Google Inc.
•
Wi-Fi® is a registered trademark of Wi-Fi Alliance®.
•
Wiser™ is a trademark and the property of Schneider Electric, its subsidiaries
and affiliated companies.
Other brands and registered trademarks are the property of their respective owners.
Schneider Electric
35 rue Joseph Monier
92500 Rueil Malmaison
France
+ 33 (0) 1 41 29 70 00
www.se.com
As standards, specifications, and design change from time to time,
please ask for confirmation of the information given in this publication.
© 2022 – Schneider Electric. All rights reserved.
DUG_Exxact Motion Sensor MW Dimmer_WSE-00

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project