Schneider Electric Magelis iPC - Industrial PCs User Manual

MAGELIS iPC

Industrial PCs

User manual

MPC ENx xxxx xxx

MPC DN xxxx xxx

MPC NA/NB/NTxx

eng www.telemecanique.com

2

Table of Contents

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

About the Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Part I

General overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Chapter 1

Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Additional Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Federal Communications Commission Radio Frequency Interference Statement -

For U.S.A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Qualified Personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Hazardous Location Installations for USA and Canada . . . . . . . . . . . . . . . . . . . 18

Safety Warnings - For U.K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Safety Agency Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Compliance of use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Replacement and recycling of used batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Chapter 2

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Chapter 3

Physical overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

3.1

Description of the Control Boxes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

MPC DN••• Control Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

MPC EN••• Control Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

3.2

Description of the front panels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

MPC NA•• and MPC NB•• front panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

MPC NT•• front panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

3

4

Chapter 4

Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

4.1

Control Box specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Characteristics of MPC DN• •••• ••• products . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Characteristics of MPC EN• •••• ••• products . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

4.2

Characteristics of the front panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Characteristics of the front panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

4.3

Environmental characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Environmental characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

4.4

Limitations on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Chapter 5

Specific functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

New Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Specific keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Touch-sensitive cursor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Control drawing of the PS/2 outlet on the Magelis iPC front panels . . . . . . . . . . 68

Installation of Kit MPC YN0 0HLK 20N for Class I, Division 2 Hazardous Locations.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Part II

Recommendations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Chapter 6

Recommendations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Integration of the iPC and Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Environmental conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Part III

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Chapter 7

Dimensions/Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Dimensions of the Front Panels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Other dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Cut out dimensions for cabinet installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Panel mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Mounting in 19" rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Mounting without a front panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Assembly of the front panel onto the Control Box . . . . . . . . . . . . . . . . . . . . . . . . 92

Mains supply of the Control Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Direct current supply of Control Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Chapter 8

Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

First power-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Chapter 9

Configuration of the Bios. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Accessing the BIOS configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Configuration screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Modifying the date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Modifying the User password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Chapter 10

Hardware extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Removing/inserting the Hard Disk drive CD-RW/DVD-R drive . . . . . . . . . . . . . 110

Disassembling the modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Installing an extension card for MPC DN•• . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

Installing an extension card for MPC EN•• . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

Adding a memory extension card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

Part IV

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Chapter 11

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

Reinstallation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Replacing dust filters for MPC DN•• . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Replacing dust filters for MPC EN•• . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

Part V

Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

Chapter 12

Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

Index

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

5

6

Safety Information

§

Important Information

NOTICE Read these instructions carefully, and look at the equipment to become familiar with the device before trying to install, operate, or maintain it. The following special messages may appear throughout this documentation or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.

The addition of this symbol to a Danger or Warning safety label indicates that an electrical hazard exists, which will result in personal injury if the instructions are not followed.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER

DANGER indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.

WARNING

WARNING indicates a potentially hazardous situation, which, if not avoided, can result in death, serious injury, or equipment damage.

7

08/2006

Safety Information

CAUTION

CAUTION indicates a potentially hazardous situation, which, if not avoided, can result in injury or equipment damage.

PLEASE NOTE Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material.

© 2006 Schneider Electric. All Rights Reserved.

8

08/2006

About the Book

At a Glance

Document Scope This user manual deals with the setting of the Magelis iPC range of industrial PCs

Validity Note Schneider Electric assumes no responsibility for any errors that may appear in this document. If you have any suggestions for improvements or amendments or have found errors in this publication, please notify us.

No part of this document may be reproduced in any form or by any means, electronic or mechanical, including photocopying, without express written permission of

Schneider Electric.

The data and illustrations found in this documentation are not binding. We reserve the right to modify our products in line with our policy of continuous product development. The information in this document is subject to change without notice and should not be construed as a commitment by Schneider Electric.

Revision History

Rev. No.

1

Changes

Initial version.

Related

Documents

Title of Documentation

Magelis iPC installation guide

Safety Guidelines for the Application, Installation, and Maintenance of Solid State Control

Safety Standards for Construction and Guide for Selection,

Installation and Operation of Adjustable-Speed Drive Systems

Reference Number

35012231

NEMA ICS 1.1

NEMA ICS 7.1

08/2006

9

About the Book

Product Related

Warnings

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH z The mains plug on this equipment must be used to disconnect the mains power.

z Remove all power before removing any covers or elements of the system and installing or removing any hardware cables.

z Always use a properly rated voltage sensing device to confirm power is off.

z Wait 10 minutes before removing covers.

z Replace and secure all covers or elements of the system before applying power to the unit.

Failure to follow this instruction will result in death or serious injury.

WARNING

LOSS OF CONTROL z The designer of any control scheme must consider the potential failure modes of control paths and, for certain critical control functions, provide a means to achieve a safe state during and after a path failure.

z Examples of critical control functions are emergency stop and overtravel stop.

z Separate or redundant control paths must be provided for critical control functions.

z System control paths may include communication links. Consideration must be given to the implications of unanticipated transmission delays or failures of the link. * z Each implementation of a Magelis iPC must be individually and thoroughly tested for proper operation before being placed into service.

Failure to follow this instruction can result in death, serious injury, or equipment damage.

10

08/2006

About the Book

Note: * For additional information, refer to NEMA ICS 1.1 (latest edition), "Safety

Guidelines for the Application, Installation, and Maintenance of Solid State Control" and to NEMA ICS 7.1 (latest edition), "Safety Standards for Construction and

Guide for Selection, Installation and Operation of Adjustable-Speed Drive Systems

User Comments We welcome your comments about this document. You can reach us by e-mail at [email protected]

08/2006

11

About the Book

12

08/2006

General overview

I

At a Glance

Subject of this part

What's in this

Part?

This part provides an overview of the industrial PCs in the Magelis iPC range.

This part contains the following chapters:

Chapter

1

2

3

4

5

Chapter Name

Important Information

Introduction

Physical overview

Characteristics

Specific functions

Page

15

29

31

41

55

08/2006

13

General overview

14

08/2006

Important Information

1

Additional Safety Information

General

What's in this

Chapter?

This chapter describes safety aspects which are specific to the operation of Magelis

Modular iPC

This chapter contains the following topics:

Topic

Federal Communications Commission Radio Frequency Interference

Statement - For U.S.A.

Qualified Personnel

Hazardous Location Installations for USA and Canada

Safety Warnings - For U.K.

Safety Agency Approval

Compliance of use

Replacement and recycling of used batteries

Page

16

17

18

24

26

26

27

15

08/2006

Important Information

Federal Communications Commission Radio Frequency Interference Statement

- For U.S.A.

Equipment

Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: z z z z

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the Support Service Center or an experienced radio/TV technician for help.

WARNING

UNINTENDED EQUIPMENT OPERATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: z This device may not cause harmful interference received, including interference that may cause undesired operation.

z This device must accept any interference received, including interference that may cause undesired operation.

Failure to follow this instruction can result in death, serious injury, or equipment damage.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

16

08/2006

Important Information

Qualified Personnel

Safety Aspects Only qualified personnel are authorized to implement, operate or maintain the products. The implementation by non-qualified persons or failure to observe the safety instructions contained in this manual, or attached to the devices, can endanger the personnel and/or do irreparable damage to the equipment. The following persons can be designated as " qualified personnel ": z z z z at application design level, engineering department personnel who are familiar with automation safety concepts (for example, a design engineer), at equipment implementation level, personnel who are familiar with the installation, connection and commissioning of automation equipment (for example, an installation assembly or cabling engineer, or a commissioning technician), at operation level, personnel who are experienced in the use and control of automation equipment (for example, an operator), as far as preventive or corrective maintenance is concerned, persons trained and qualified in regulating or repairing automatic devices (for example an operating technician, or an after-sales service technician, etc.).

08/2006

17

Important Information

Hazardous Location Installations for USA and Canada

General Schneider Automation designed the systems with the intention of meeting the requirements of Class I, Division 2 hazardous location applications. Division 2 locations are those locations that are normally non-hazardous, but potentially hazardous should an accident expose the area to flammable vapors, gases or combustible dusts.

These systems are non-incendiary devices. They are not intrinsically safe and should never be operated within a Division 1 (normally hazardous) location when installed as described here. Nor should any peripheral interface device attached to these systems be located within Division 1 locations unless approved and/or certified diode barriers are placed in series with each individual signal and DC power line. Any such installations are beyond the bounds of Schneider Automation design intent. Schneider Automation accepts no responsibility for installations of this equipment or any devices attached to this equipment in Division 1 locations.

It is mandatory to install the Hazardous Location Kit Ref: MPC YN0 0HLK 20N.

WARNING

EXPLOSION HAZARD

For AC version of this equipment: The power switch is an arcing device. It should be switched to the ON position, and the corresponding retainer bracket for the

Control Box should be attached according to the Hazardous Location Kit service instruction.

Failure to follow this instruction can result in death, serious injury, or equipment damage.

18

08/2006

08/2006

Important Information

WARNING

HAZARDOUS LOCATION COMPLIANCE

In case of maintenance or repair of any subassembly, the user must verify that the exchanged or repaired module is labelled as a Class 1 Division 2 hazardous location. Substitution of components may impair suitability for Class 1, Division 2.

Suitable for use in Class 1, Division 2 Groups A, B, C, and D, hazardous or nonhazardous locations only.

For use in hazardous locations, the PCI or ISA controller cards shall be found in category NWHP2, provided that they are suitable for Class 1, Division 2, Groups

A, B, C, and D; T-Code: T4A, and suitable for an ambient temperature range of

0° C to +50 °C.

Do not connect or disconnect equipment unless the power has been removed or the area is known to be non-hazardous.

Power wiring must be in accordance with the National Electrical Code, article

501.4(B) for Class 1, Division 2.

When in hazardous locations, remove power before replacing or wiring modules.Do not connect or disconnect the output ports such as PS2/USB/Serial/

Parallel/Video connectors when the unit is in a Hazardous Location area.

Failure to follow this instruction can result in death, serious injury, or equipment damage.

Only technically qualified service personnel should perform installation and service.

These workstations are designed to require no service in the course of normal operation by an operator.

It is the responsibility of the customer to ensure that the product is properly rated for the location. If the intended location does not presently have a Class, Division and

Group rating, then users should consult the appropriate authorities having jurisdiction in order to determine the correct rating for that hazardous location.

In accordance with Federal, State/Provincial, and Local regulations, all hazardous location installations should be inspected prior to use by the appropriate authority having jurisdiction. Only technically qualified personnel should install, service, and inspect these systems.

19

Important Information

Definition The following Class and Division explanations are derived from Article 500 (Sections

5 and 6) of the United States National Fire Protection Agency National Electric Code

(NFPA 70, 1990). They are not complete and are included here only for a general description for those not familiar with generic hazardous locations requirements.

Persons responsible for the installation of this equipment in hazardous locations are responsible for ensuring that all relevant codes and regulations related to location rating, enclosure, and wiring are met.

Class I Locations

Class I locations are those in which flammable gases or vapors are or may be present in the air in quantities sufficient to produce explosive or ignitable mixtures.

Class II Locations

Class II locations are those that are, or may become, hazardous because of the presence of combustible dust.

Division 1 Locations

A Division 1 location is one in which flammable or ignitable gases, vapors or combustible dusts and particles can exist due the following conditions: z z z

Normal operating conditions.

Due to repair, maintenance conditions, leakage, or where mechanical failure or abnormal operation of machinery or equipment might release or cause explosive or ignitable mixtures to be released or produced.

Combustible dusts of an electrically conductive nature may be present in hazardous quantities.

Note: Schneider Automation MPC••• systems are not suitable for installation within

Class II Division 2 and Class 1 Division 1 locations.

Electrical equipment cannot be installed in Division 1 locations unless they are intrinsically safe, installed inside approved explosion-proof enclosures, or installed inside approved purged and pressurized enclosures

20

08/2006

08/2006

Important Information

Division 2 Locations z z z z

Class I volatile flammable liquids or flammable gases are handled, processed or used, but confined within closed containers or closed systems from which they can escape only in cases of accidental rupture or breakdown of such enclosures or systems, or in case of abnormal operation of equipment.

Ignitable concentrations of Class I vapors or gases are normally prevented by positive mechanical ventilation, but may become hazardous due to mechanical failure of those ventilation systems.

Location is adjacent to a Division 1 location.

Class II combustible dust is not normally in the air in quantities sufficient to produce explosive or ignitable mixtures. Dust accumulations are normally insufficient to interfere with normal operation of electrical equipment or other apparatus. Combustible dust may be in suspension in the air as a result of the following: infrequent malfunctioning of handling or processing equipment; combustible dust accumulations on, or in the vicinity of, electrical equipment; may be ignitable by abnormal operation or failure of electrical equipment.

Groups

All electrical equipment that is approved for use in hazardous locations must include a group rating. Various flammable and combustible substances are divided into these groups as a function of their individual maximum experimental safe gap

(MESG), explosion pressure, and ignition temperature. Component temperatures and the potential for spark based upon voltage, current and circuit characteristics of electrical equipment will determine what the equipment group rating will be. A device approved for installation within Class I, Group A locations may also be used in

Groups B, C, or D.

Note: Approved Class I equipment may not be suitable for Class II installations.Class I includes Groups A, B, C, and D. Class II includes Groups F, and G

21

Important Information

Power Switch

Cable connections

The amount of input power required by these systems classifies a power switch as an incendiary device because the voltage and current across the make/break device are capable of creating a spark.

Hazardous location regulations require that a power switch rated for ordinary locations may be used if it is located in an area specified as non-hazardous.

However, limits in cable length between the workstation and the power switch may apply. Otherwise the switch must be compliant with Class I, Division 1 requirements

(intrinsically safe). These switches are built in a manner that prevents the possibility of a spark when contacts are made or broken.

Use suitable UL listed and/or CSA Certified Class I, Division 1 switches in hazardous locations. These switches are available from a wide number of sources. It is the responsibility of the customer to ensure that the power switch selected for the installation has the correct hazardous locations rating for the location in which it is installed.

Division 2 hazardous location regulations require that all cable connections be provided with adequate strain relief and positive interlock. USB connections can never be used in hazardous location installations, because USB connectors do not provide adequate strain relief. Never connect or disconnect a cable while power is applied at either end of the cable. All communication cables should include a chassis ground shield. This shield should include both copper braid and aluminum foil. The

D-sub style connector housing should be a metal conductive type (e.g., molded zinc) and the ground shield braid should be well terminated directly to the connector housing. Do not use a shield drain wire.

The outer diameter of the cable must be suited to the inner diameter of the cable connector strain relief in order to ensure that a reliable degree of strain relief is maintained. Always secure the D-Sub connectors to the workstation-mating connectors via the two screws located on both sides.

WARNING

EXPLOSION HAZARD

Never connect or disconnect the communication cables while power is applied at either end of the cable. This may result in an incendiary spark. Permanent damage to the workstation communication components may occur.

Failure to follow this instruction can result in death, serious injury, or equipment damage.

22

08/2006

Operation and

Maintenance

Important Information

The systems have been designed for compliance with relevant spark ignition tests.

However, please note that the workstation front panel keypad switches and PS/2 connector are the only make/break components intended to be exercised by the operator in the course of normal operation.

WARNING

EXPLOSION HAZARD

The front PS/2 connector provides a non incendive field circuit in accordance with the control drawing located in Chapter 5.

Failure to follow this instruction can result in death, serious injury, or equipment damage.

Always observe the following rules with respect to hazardous location installations: z z z

Always install the workstations within an enclosure suitable for the specific application. General-purpose enclosures may be acceptable for Class I applications but are never acceptable for Class II applications. Type 4 (IP 65) enclosures are recommended even when not required by regulations.

If present, keep enclosure doors or openings closed at all times, to avoid the accumulation of foreign matter inside the workstation.

Never subject the unit to any installation or service procedures unless power is removed and the area is known to be non-hazardous. This includes the installation or removal of power cables, communication cables, or removal of the rear cover of the unit.

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH z The mains plug on this equipment must be used to disconnect the mains power.

z Remove all power before removing any covers or elements of the system and installing or removing any hardware and cables. Insure that the area is nonhazardous.

z Always use a properly rated voltage sensing device to confirm power is off.

z Wait 10 minutes before removing covers.

z Replace and secure all covers or elements of the system before applying power to the unit.

Failure to follow this instruction will result in death or serious injury.

08/2006

23

Important Information

Safety Warnings - For U.K.

Earthing and

Wiring

UNDERGROUND EQUIPMENT

WARNING

This apparatus must be earthed for your safety.To ensure safe operation the three-pin plug must be inserted only into a standard three-pin power point, which is effectively earthed through the normal household wiring.

Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth. Incorrectly wired extension cords are a major cause of fatalities.

The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe.For your safety, if you have any doubt about the effective earthing of the power point, consult a qualified electrician.

Failure to follow this instruction can result in death, serious injury, or equipment damage.

WARNING

IMPROPER WIRING

The mains plug on this equipment must be used to disconnect the mains power.

Failure to follow this instruction can result in death, serious injury, or equipment damage.

As the colors of the wires in the mains lead of this apparatus may not correspond with the colored markings identifying terminals in your plug, proceed as follows.

Mains Lead

Function

–

Earth

–

Neutral

Live

Color

–

Green-Yellow

–

Blue

Brown

Equipment Terminal

Color Marking

–

Green

Green-Yellow

E

Earth Symbol

Earth Symbol

Black

Red

N

L

24

08/2006

08/2006

Important Information

WARNING

INCOMPATIBLE SYSTEM

Do not connect this equipment to an IT power system:

Disconnect the mains plug from the supply socket when the computer is not in use.

Failure to follow this instruction can result in death, serious injury, or equipment damage.

Note: An IT system is a system having no direct connections between live parts and Earth; the exposed conductive parts of the electrical installation are earthed.

An IT system is not permitted where the computer is directly connected to public supply systems in the UK.

25

Important Information

Safety Agency Approval

Standards The Schneider Automation systems are designed to meet the following standards: z z z z

Underwriters Laboratories Inc., UL 1604 Standard for Safety Electrical equipment for use in Class I Division 2 locations

Canadian Standard Association, Specification C22.2 No. 213-M1987 Nonincendiary electrical equipment for use in Class I, Division 2 hazardous locations.

Canadian Standards Association, Specification C22.2

EN 60950, Industrial Control Equipment

Compliance of use

European

Directive

The products described in the present documentation comply with the European

Directives* to which they are subject (CE marking). However, these can only be used correctly in applications for which they are specifically intended, as specified in the relevant documentation, and in connection with approved third-party products.

As a general rule, correct usage of the products, with no danger to personnel or hardware, consists of complying with all handling, transport and storage recommendations, and all installation, operation and maintenance instructions.

* EMCD and LVD directives concerning Electromagnetic Compatibility and Low

Voltage.

26

08/2006

Important Information

Replacement and recycling of used batteries

Lithium battery The terminal contains a lithium battery, which is used to save certain data such as the date and time.

WARNING

FIRE OR CHEMICAL HAZARD

Lithium batteries used in this device may present a risk of fire or chemical burn if not handled properly.

z Batteries are to be replace only by a qualified Schneider Technician z Do not recharge, disassemble, heat above 100° C ( 212° F) or incinerate.

z Recycle or properly dispose of.

z Follow all battery manufacturers’ instructions

Failure to follow this instruction can result in death, serious injury, or equipment damage.

08/2006

27

Important Information

28

08/2006

Introduction

2

Introduction

At a Glance Magelis Modular iPC computers are modular products, made up of a Control Box and a Front Panel that you have to assemble prior to commissioning (see Assembly

of the front panel onto the Control Box, p. 92).

The Control Box may however be used as stand-alone with a video monitor and an external keyboard (see

Mounting without a front panel, p. 91).

There are two versions of the Control Box: z z

References: MPC DN•••

References: MPC EN••• with different characteristics (see

Control Box specifications, p. 42).

The Control-Boxes also use a modular design in order to facilitate maintenance. For example the MPC DN••• is made up of a power supply block, a control box block and a block for extension cards.

There are several versions of the front panel: z z z

15" LCD screen

With or without built-in dust and damp proof keyboard

LCD screen may or may not be touch-sensitive

Note: Magelis Modular iPCs are supplied with a warranty sticker clearly attached to the unit. Modifications/opening of the product that removes or tampers with this sticker will void the Schneider warranty for the product.

29

08/2006

Introduction

30

08/2006

Physical overview

3

At a Glance

Subject of this chapter

What's in this

Chapter?

This chapter provides physical overviews of the products.

This chapter contains the following sections:

Section

3.1

3.2

Topic

Description of the Control Boxes

Description of the front panels

Page

32

37

08/2006

31

Physical overview

3.1

Description of the Control Boxes

At a Glance

Subject of this

Section

What's in this

Section?

This section describes the different models of the Control Box.

This section contains the following topics:

Topic

MPC DN••• Control Box

MPC EN••• Control Box

Page

33

35

32

08/2006

MPC DN••• Control Box

Description MPC DN•••:

DC Plate

AC Plate

Physical overview

7

3

1

3

8 5 6

MPC DN••• and associated items:

16

12

11

14

15

08/2006

13 10 9 4

2

14

33

Physical overview

10

11

12

13

8

9

6

7

14

15

16

MPC DN Legend Table

4

5

2

3

Number

1

Designation

Front panel connector

Hard disk drive

Removable CD-RW/DVD-ROM and disk drive drawer

RJ45 Ethernet link connector

15-pin, female, VGA out put SUB-D connector for connection to an external video monitor

25-pin, female, LPT parallel port SUB-D connector for printer.

PCMCIA extension card slots

2 x 9-pin, male RS-232 serial port SUB-D connectors

External keyboard input

External mouse input

Mains or 24 VDC terminal block socket

On-Off switch

2 USB port connectors

Ventilation with dust filters

Block with slots for extension cards

Temperature alarm block

Note: The external keyboard input (No. 9) and external mouse input (No. 10) can only be used when the Control Box is used without Front Panel with an external video monitor.

34

08/2006

Physical overview

MPC EN••• Control Box

Description MPC EN•••:

3

1

MPC EN••• and associated items:

5

8

6

7

13

4

2

10 9

16

08/2006

14

11

DC Plate

AC Plate

11

16

12

35

Physical overview

MPC EN Legend Table

10

11

12

13

8

9

6

7

14

15

16

4

5

2

3

Number Designation

1 Front panel connector

Hard disk drive

Removeable CD-RW/DVD-ROM and disk drive drawer

RJ45 Ethernet link connector

15-pin, female, VGA out put SUB-D connector for connection to an external video monitor

25-pin, female, LPT parallel port SUB-D connector for printer.

PCMCIA extension card slots

2 x 9-pin, male RS-232 serial port SUB-D connectors

External keyboard input

External mouse input

Mains or 24 VDC terminal block socket

On-Off switch

2 USB port connectors

Ventillation with dust filters

Block with slots for extension cards

Temperature alarm block

Note: The external keyboard input (No. 9) and external mouse input (No. 10) can only be used when the Control Box is used without Front Panel with an external video monitor.

36

08/2006

3.2

Description of the front panels

At a Glance

Subject of this section

What's in this

Section?

This section describes the different front panels of the products.

This section contains the following topics:

Topic

MPC NA•• and MPC NB•• front panels

MPC NT•• front panels

Physical overview

Page

38

39

08/2006

37

Physical overview

MPC NA•• and MPC NB•• front panels

At a Glance

Description

These front panels come with a 15" screen and a keyboard. For the MPC NB••, the screen is touch-sensitive.

View of an MPC NA•• or MPC NB•• front panel

Screen (touch-sensitive for MPC NB••

)

LEDs User function**/Alpha keys

Number keypad and arrow keys

External keyboard/mouse socket

Infra-red link

Function/

Alpha keys

Function/Alpha switch key

**The user function keys can be used by an application.

For more information refer to

Specific keys, p. 63

Touch-sensitive cursor

38

08/2006

Physical overview

MPC NT•• front panels

At a Glance

Description

These front panels come with a 15" touch-sensitive screen.

View of an MPC NT•• front panel

LEDs

Touch-sensitive screen

Brightness control

External keyboard/mouse socket*

Infra-red link

*See

Specific keys, p. 63

08/2006

39

Physical overview

40

08/2006

Characteristics

At a Glance

Subject of this chapter

What's in this

Chapter?

This chapter gives the product characteristics.

This chapter contains the following sections:

Section

4.1

4.2

4.3

4.4

Topic

Control Box specifications

Characteristics of the front panels

Environmental characteristics

Limitations on use

4

Page

42

47

48

49

08/2006

41

Characteristics

4.1

Control Box specifications

At a Glance

Subject of this

Section

What's in this

Section?

This section specifies the characteristics of the Control Boxes.

This section contains the following topics:

Topic

Characteristics of MPC DN• •••• ••• products

Characteristics of MPC EN• •••• ••• products

Page

43

45

42

08/2006

Characteristics

Characteristics of MPC DN• •••• ••• products

Introduction

Control Box

Characteristics

The characteristics of the MPC DN• •••• ••• products differ from model to model.

These are given below according to product reference.

Characteristics:

Component

Hard disk

RAM

CD-ROM drive

Floppy Disk drive

Video card

Extension slots

Input/Output ports

Dimensions

Weight

Decription

≥

40 GB IDE - 2.5 "

SDRAM 512 Mb extensible up to 2 Gb (2 slots memory maximum)

24 x speed or combo drive of DVD reader or CD writer (optional)

3.5 " 1.44 MB (fixed)

64 bit RAM 2 Mb (fixed)

4 x slots PCI bus and 2 slots PCMCIA type I/II (or 1 type III) z 1 x Ethernet TCP/IP port 10BASE-T/100BASE-TX (RJ45 connector) z 2 x USB ports (12 MBit/s) z 1 x COM4 RS 232 serial port (SUB-D male 9-contacts connector) z 1 x COM1 RS 232 serial port (SUB-D male 9-contacts connector) z 1 x bi-directional parallel port (connector type SUB-D female

15-contact connector) z 1 x external VGA video screen port (connector type SUB-D female 15 contacts) z 1 x port for PS/2 keyboard (mini-DIN connection) (1) z 1 x port for PS/2 pointing device (mini-DIN connection) (1)

316 x 310 x 200 mm (12.4 x 12.2 x 7.9 in.)

11.3 kg (24.91 lbs)

(1) The port is not operational if the iPC is connected to a front panel.

08/2006

43

Characteristics

Processor

Power supply

Operating systems

Pre-installed packs

Type of processor according to product reference:

Reference

MPC DN• 2••• •••

MPC DN• 5••• •••

Processor

Celeron M with a clock frequency

≥

1.3 GHz

Pentium M with a clock frequency

≥

1.6 GHz

Power supply of MPC DN• ••A• ••• products (AC):

Supply voltage

Frequency

115...230 VAC - 50/60 Hz, (threshold values: 98...264 VAC)

50/60 Hz (threshold values: 47/63 Hz), EN 61131-2 compliant

Consumption 160 VA

Micro-cuts 10 ms

Power supply of MPC DN• ••D• ••• products (DC):

Supply voltage 24 VDC, (threshold values: 19...32 V)

Consumption 170 W

Micro-cuts 1 ms

The products are delivered with a pre-installed operating system according to the reference ordered.

The products have been tested and are guaranteed with the following operating systems: z z

Microsoft Windows 2000

Microsoft Windows XP Pro

Pre-installed packs according to product reference:

Reference

MPC DN• •••• ••A

MPC DN• •••• ••B

Software

Vijeo Look Run Time

Vijeo Look Build Time

44

08/2006

Characteristics

Characteristics of MPC EN• •••• ••• products

Introduction

Control Box

Characteristics

The characteristics of the MPC EN• •••• ••• products differ from model to model.

These are given below according to product reference.

Characteristics:

Component

Hard disk

RAM

CD-ROM drive

Floppy Disk drive

Video card

Extension slots

Input/Output ports

Dimensions

Weight

Description

≥

40 GB IDE - 2.5 "

SDRAM 512 Mb extensible to 2 Gb (2 slots memory maximum)

24 x speed or combo drive of DVD reader or CD writer (optional)

3.5 ", 1.44 MB (fixed)

64 bit RAM 2 Mb (fixed)

1 x slots PCI bus and 2 slots PCMCIA type I/II (or 1 type III) z 1 x Ethernet TCP/IP port 10BASE-T/100BASE-TX (RJ45 connector) z 2 x USB ports (12 MBit/s) z 1 x COM4 RS 232 serial port (SUB-D male 9-contacts connector) z 1 x COM1 RS 232 serial port (SUB-D male 9-contacts connector) z 1 x bi-directional parallel port (connector type SUB-D female

15-contact connector) z 1 x external VGA video screen port (connector type SUB-D female 15 contacts) z 1 x port for PS/2 keyboard (mini-DIN connection) (1) z 1 x port for PS/2 pointing device (mini-DIN connection) (1)

316 x 310 x 110 mm (12.4 x 12.2 x 4.33 in)

7.5 Kg 16.53 lbs

(1) Port is non operational if the iPC is connected to a front panel.

08/2006

45

Characteristics

Processor

Power supply

Operating systems

Pre-installed packs

Type of processor according to product reference:

Reference

MPC EN• 2••• •••

MPC EN• 5••• •••

Processor

Intel Celeron M with a clock frequency

≥

1.3 GHz

Intel Pentium M with a clock frequency

≥

1.6 GHz

Power supply of MPC EN• ••A• ••• products (AC):

Supply voltage

Frequency

115...230 VAC - 50/60 Hz, (threshold values: 90...264 VAC)

50/60 Hz (threshold values: 47/63 Hz), EN 61131-2 compliant

Consumption 130 VA

Micro-cuts 10 ms

Power supply of MPC EN• ••D• ••• products (DC):

Supply voltage 24 VDC, (threshold values: 18...36 V)

Consumption 140 W

Micro-cuts 1 ms

The products are delivered with a pre-installed operating system according to the reference ordered.

The products have been tested and are guaranteed with the following operating systems: z z

Microsoft Windows 2000

Microsoft Windows XP Pro

Pre-installed packs according to product reference:

Reference

MPC EN• •••• ••A

Software

Vijeo Look Run Time

46

08/2006

Characteristics

4.2

Characteristics of the front panels

Characteristics of the front panels

Introduction The characteristics of the front panels differ from model to model. These are given below.

Characteristics

Reference

MPC NT5•

MPC NA5•

MPC NB5•

Shared characteristics:

Number of colors

Brightness

Infra-red link

Power supply

≥

262,144

200 Cd/m

2

(typical value), adjustable

IrDA Standard

By Control Box unit

Specific characteristics:

Screen type

Screen size

Definition View angle Touch-sensitive

Screen

TFT active matrix

TFT active matrix

15 "

15 "

1024 x 768 Hor. 160 °

Vert. 160 °

1024x768 Hor. 160°

Vert. 160°

Analog resistant

35 million cycles

-

TFT active matrix

15 " 1024x768 Hor. 160 °

Vert. 160 °

Analog resistant

35 million cycles

Keyboard

-

Weight

(Kg)

9.3

IBM standard 70-key alphanumeric

2x10 user function keys

IBM standard 70-key alphanumeric

2x10 user function keys

9.3

9.3

For the front-panel dimensions, please refer to

Other dimensions, p. 85

08/2006

47

Characteristics

4.3

Environmental characteristics

Environmental characteristics

General The environmental characteristics given below are applicable to both the Control

Boxes and the front panels of the products.

Characteristics

Specification

Degree of Protection

Storage temperature

Usage altitude

Storage altitude

Vibration

(in operation)

Shock Resistance

(in operation)

Humidity

Interference immunity

The environmental characteristics are as follows:

Operating- temperature)

Value z z

IP65 for the forward part of the front panels.

IP 20 for the rest of the product

0 to 50 °C (32 to122 °F)

-25 to 60 °C

0...3000 m

0...12000 m

–

(-13 to 140 °F)

(9000 ft max)

(36000 ft max)

Standards

–

In accordance with EN 61131-2, UL 508 for standard location, UL 1604 for Class I,

Division 2 hazardous location.

IEC 68-2-2 Bb and Ab tests,

IEC 68-2-14 Na test and EN 61131-2 compliant

–

–

IEC 68-2-6 Fc test and EN 61131-2 compliant

15 g over 11 ms IEC 68-2-27 Ea test and EN 61131-2 compliant

20 % to 80 % RH @ 40 °C (104 °F) –

High frequency interference

Electromagnetic Emissions

Human and material safety

EN 61131, IEC 1000-4-3/6 level 3

Class A/EN 55022/55011

EN 61131-2, UL/CSA and IEC 529/IEC 950

48

08/2006

Characteristics

4.4

Limitations on use

Limitations

At a Glance

CD reader

Combo drive

USB Interfaces

The limitations given below are applicable to the products equipped with CD-reader/

Combo drive devices and also for USB Interfaces.

The CD reader has a maximum operating shock value of 0.2 GHz and a maximum operating vibration value of 5 GHz. Operating the drive outside these limits may cause the drive to function incorrectly.

The combo drive has a maximum operating shock value of 0.2 GHz and a maximum operating vibration value of 5 GHz. Operating the drive outside these limits may cause the drive to function incorrectly.

The ambient operating temperature for the Combo drive is 45 °C + 0 ° - 5 °C.

Operating the drive outside these limits may cause the drive to function incorrectly.

USB ports are intended to connect to especially low consumption devices

(keyboard, mouse, pointing devices). If it is intended to connect a power demanding devices (HDD, CD-ROM), the device must provide its own external power.

The USB connector is not a latching type and so this type of connection is only permissible inside hazardous locations, if means can be provided, preventing mechanically, any accidental disconnection.

Limitations context PCMCIA cards

With the default configuration, two 16-bit mode PCMCIA cards cannot be used at the same time. If necessary, the COM4 serial port can be disabled in order to use two

16-bit mode PCMCIA cards.

08/2006

49

Characteristics

Disabling COM4 port procedure

The procedure for disabling the COM4 port is as follows in the BIOS menu:

1 APIC disabled: Advanced BIOS Features APIC Mode Disabled

2

Phoenix - AwardBIOS CMOS Setup Utility

Advanced CMOS Features

CPU Feature

Hard Disk Boot Priority

CD-ROM Boot Priority

Virus Warning

CPU L1 & L2 Cache

Quick Power On Self Test

First Boot Device

Second Boot Device

Third Boot Device

Boot Other Device

Swap Floppy Drive

Boot Up Floppy Disk

Boot Up NumLock Status

Gate A20 Option

Typematic Rate Setting

Typematic Rate (Chars/Sec)

Typematic Delay (Msec)

Security Option

APIC Mode

[Press Enter]

[Press Enter]

[Press Enter]

[Disabled]

[Enabled]

[Enabled]

[Hard Disk]

[Hard Disk]

[LS120]

[Enabled]

[Disabled]

[Enabled]

[On]

[Fast]

[Disabled]

6

250

[Setup]

[Disabled]

Item Help

Menu Level

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

COM4 disabled: Integrated Peripherals

Port 4 Disabled

Super IO Device Onboard Serial

Phoenix - AwardBIOS CMOS Setup Utility

Super IO Device

Onboard FDC Controller

Onboard Serial Port 1

UART Mode Select

UR2 Duplex Mode

Onboard Parallel Port

Parallel Port Mode

Typematic Rate (Chars/Sec)

Onboard Serial Port 3

Serial Port 3 use IRQ

Onboard Serial Port 4

Serial Port 4 use IRQ

[Enabled]

[3F8/IRQ4]

[IrDA]

[Half]

[378/IRQ7]

[SPP]

3

[3E8]

[IRQ10]

[Disabled]

[IRQ11]

Item Help

Menu Level

50

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

08/2006

08/2006

Characteristics

3 IRQ 9/11 reserved: PnP/PCI Configurations

[Manual] IRQ Resources

Resources Controlled By

IRQ 9/11 assigned to Reserved

Phoenix - AwardBIOS CMOS Setup Utility

PnP/PCI Configurations

Reset Configuration Data

Resources Controlled by

IRQ Resources

[Disabled]

[Manual]

[Press Enter]

PCI/VGA Palette Snoop [Disabled]

Item Help

Menu Level

BIOS can automatically configure all the boot and Plug and Play compatible device.

If you choose Auto, you cannot select IRQ

DMA and memory base address fields, since

BIOS automatically assigns them

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Phoenix - AwardBIOS CMOS Setup Utility

IRQ Resources

IRQ-3 assigned to

IRQ-4 assigned to

IRQ-5 assigned to

IRQ-7 assigned to

IRQ-9 assigned to

IRQ-10 assigned to

IRQ-11 assigned to

IRQ-12 assigned to

IRQ-14 assigned to

IRQ-15 assigned to

[PCI Device]

[PCI Device]

[PCI Device]

[PCI Device]

[Reserved]

[PCI Device]

[Reserved]

[PCI Device]

[PCI Device]

[PCI Device]

Item Help

Menu Level

Legacy ISA for devices compliant with the original PC AT bus specification, PCI/ISA

PnP for devices compliant with the

Plug and Play standard whether designed for

PCI or ISA bus architecture

4

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Save the modifications by pressing F10 .

51

Characteristics

Enabling COM4 port procedure

The procedure for enabling the COM4 port is as follows in the BIOS menu:

1 APIC enabled: Advanced BIOS Features APIC Mode Enabled

2

Phoenix - AwardBIOS CMOS Setup Utility

Advanced CMOS Features

CPU Feature

Hard Disk Boot Priority

CD-ROM Boot Priority

Virus Warning

CPU L1 & L2 Cache

Quick Power On Self Test

First Boot Device

Second Boot Device

Third Boot Device

Boot Other Device

Swap Floppy Drive

Boot Up Floppy Disk

Boot Up NumLock Status

Gate A20 Option

Typematic Rate Setting

Typematic Rate (Chars/Sec)

Typematic Delay (Msec)

Security Option

APIC Mode

[Press Enter]

[Press Enter]

[Press Enter]

[Disabled]

[Enabled]

[Enabled]

[Hard Disk]

[Hard Disk]

[LS120]

[Enabled]

[Disabled]

[Enabled]

[On]

[Fast]

[Disabled]

6

250

[Setup]

[Enabled]

Item Help

Menu Level

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

COM4 enabled: Integrated Peripherals

Port 4 2E8

Super IO Device Onboard Serial

Phoenix - AwardBIOS CMOS Setup Utility

Super IO Device

Onboard FDC Controller

Onboard Serial Port 1

UART Mode Select

UR2 Duplex Mode

Onboard Parallel Port

Parallel Port Mode

Typematic Rate (Chars/Sec)

Onboard Serial Port 3

Serial Port 3 use IRQ

Onboard Serial Port 4

Serial Port 4 use IRQ

[Enabled]

[3F8/IRQ4]

[IrDA]

[Half]

[378/IRQ7]

[SPP]

3

[3E8]

[IRQ10]

[2E8]

[IRQ11]

Item Help

Menu Level

52

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

08/2006

08/2006

Characteristics

3 IRQ 9/11 auto: PnP/PCI Configurations

[Auto(ESCD)]

Resources Controlled By

Phoenix - AwardBIOS CMOS Setup Utility

PnP/PCI Configurations

Reset Configuration Data [Disabled]

Resources Controlled by

IRQ Resources

[Auto(ESCD)]

Press Enter

PCI/VGA Palette Snoop [Disabled]

Item Help

Menu Level

BIOS can automatically configure all the boot and Plug and Play compatible device.

If you choose Auto, you cannot select IRQ

DMA and memory base address fields, since

BIOS automatically assigns them

4

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Save the modifications by pressing F10 .

53

Characteristics

54

08/2006

Specific functions

5

At a Glance

Subject of this chapter

What's in this

Chapter?

This chapter describes the specific functions of MPC products.

This chapter contains the following topics:

Topic

New Features

Specific keys

Touch-sensitive cursor

LED indicators

Control drawing of the PS/2 outlet on the Magelis iPC front panels

Installation of Kit MPC YN0 0HLK 20N for Class I, Division 2 Hazardous

Locations.

Page

56

63

66

67

68

69

08/2006

55

Specific functions

New Features

HDD Index of reliability

Index of reliability is an indicator which displays during start up of the iPC and a visual indicator displayed on the first screen of the BIOS auto-test.

The following is an example of the displayed message: Hardware disk reliability index 100 %

This index is calculated by taking account of all the reliability parameters of the hard disk. These parameters are permanently updated and supervised by the hard disk

Expressed as a %, the index varies from 100 % for a new hard disk to 0 % for a disk having reached its useful lifespan. The evaluation algorithms of the index being based on statistical reliability data obtained from a large hard disk sampling database, this index cannot be used to envisage breakdowns occurring in an unforeseeable way.

Under normal conditions of use and environment of the hard disk, the index decreases approximately 20 % per annum. However, this decrease may be much faster under severe conditions (temperature, shocks, vibrations, frequency of access and abnormal shutdowns).

The main purpose of the index information is to detect in advance the end of useful life of the hard disk in order to avoid any unwanted failures during exploitation.

Schneider–Electric recommends replacing the hard disk when the value of the index is approximately 20 %. Refer to

Troubleshooting, p. 127 for more information.

Note: This information does not appear if the hard disk is absent, disconnected or completely defective.

56

08/2006

Specific functions

Temperature

Monitoring

Note: Any maintenance carried out on the iPC during operation when an alarm is activated will cause rapid, irreversible damage of the product which is not covered by the guarantee.

To improve the reliability of the iPC, a device supervises the internal temperature and makes it possible to generate alarms.

At the generation of the alarm: z A contact free from potential is closed and available on an external connector block

If the operating system has been provided by Schneider–Electric, the following additional functions are also activated: z Visualization of an alarm message. This message is cleared, providing the internal temperature returns to normal and the operator has acknowledged the alarm.

z Recording of the change of alarm state in the Windows® system events manager and in a dedicated file recording temperature alarm events.

z Optional activation of operator tasks during the changes of state of alarm temperature.

08/2006

57

Specific functions

Connector Block

Temperature

Alarm

N/C Alarm θ

Power AC

+24V -24V GND

Alarm

θ

Power DC

The diagram above represents the iPC connector block according to the two available types of connection (alternate or continuous)

The two connectors in the illustration are connected to a contact free of potential with the following maximum breaking resistance specifications: z z

AC 250 V max

DC 220 V max

2 A max

2 A max

125 VA max

60 W max.

When the commuted load shows a non resistive characteristic, it is necessary to use a device adapted in order to protect the contact.

This contact is normally open and is closed as long as the internal temperature of the iPC exceeds the acceptable operating temperature.

58

08/2006

Specific functions

Alarm Message

Note: This function is only available on iPCs provided with pre-installed

Schneider–Electric software or having been re-installed using the restoration software provided by Schneider–Electric.

At the time of going beyond the maximum operating temperature, the following message will be displayed:

WARNING

- The Magelis iPC is running above the maximum temperature allowed in the specification.

- Running the Magelis iPC under these circumstances will irremediably damage the product, leading to unwanted breakdown and shortening its life time.

- Refer to User Manual for detailed instructions.

OK

Note: No functions are available, (pointer, access to other tasks and windows) providing the operator hasn’t acknowledged the Warning message.

Upon acknowledgement by the operator, the message disappears. After a varying time, the message will reappear so long as the temperature remains above the maximum operating temperature.

Temperature

Events

Recording

Note: This function is only available on iPCs provided with pre-installed

Schneider–Electric software or having been re-installed using the restoration software provided by Schneider–Electric.

Each change of alarm state (appearance and disappearance) is recorded, as well as the operator acknowledgement, in a specific events file, in the system events manager.

08/2006

59

Specific functions

Windows®

System Events

To reach this information select the icon "Working station" then right click of the mouse to the following options: "Manage", "Event observer", Application". Example of message displayed during trigger of alarm:

** Excessive temperature reached **

Example of message displayed when acknowledged by the operator:

** Temperature alarm acknowledged **

Example of message displayed at the time of the disappearance of the alarm:

** Normal return to temperature **

Example of application log

Computer Management

Fichier Action Affichage Fenêtre ?

Gestion de l’ordinateur (local)

Outils système

Observateur d’événeme

Application

Sécurité

Système

Type

Avertissem...

Avertissem...

Informations

Informations

Informations

Date

5/5/2006

5/5/2006

5/5/2006

5/5/2006

5/5/2006

Heure

10:24:41...

10:23:49...

8:23:52AM

8:23:52AM

8:18:52AM

Source Catégorie Évé

**Temperature alarm acknowledged**

**Excessive temperature reached**

(1)

(1)

ESENT

ESENT

ESENT

Général

Général

Général

1

1

101

103

102

Temperature

Alarm Events

The temperature alarm events are also recorded in the following specific file:

Windows XP C:\Windows\System\LogSchneider.log Windows

2000 C:\WinNT\System\LogSchneider.log

Example of message recorded during the generation of alarm:

Excessive temperature: 10/03/05 15:22: 06

Example of message displayed when acknowledged by the operator:

Temperature alarm acknowledged: 10/03/05 15:22: 10

Example of message recorded at the time of the disappearance of the alarm:

Normal Return to temperature: 10/03/05 15:22: 08

60

08/2006

Specific functions

Execution of

Optional Tasks

When Alarm

State Change

Note: This function is only available on iPCs provided with pre-installed

Schneider–Electric software or having been re-installed using the restoration software provided by Schneider–Electric.

In order to carry out a task or specific application when the alarm changes state

(appearance/disappearance), it is necessary to edit the following file:

Windows XP: C:\Windows\iPC _Schneider.ini

Windows 2000: C:\WinNT\iPC _Schneider.ini

Define one or both of thefollowing lines by specifying the name and path of the applications:

PROCESS_HIGH_TEMP = [Application launched during the alarm generation]

PROCESS_NORMAL_TEMP = [Application launched at the time of disappearance]

Example: In this example on the generation of alarm, the Appli1 application will be launched and at the time of disappearance of alarm, the Appli2 application will be launched. These two applications are located in the root partition of C:

PROCESS_HIGH_TEMP = C:\Appli1.exe

PROCESS_NORMAL_TEMP = C:\Appli2.exe

Note: Any executable program can be defined (exe, lnk, bat...)

If the operator wants to launch several tasks at the time of an event, it is necessary to define in file iPC _Schneider.ini a task which itself will launch the desired tasks.

CAUTION

EQUIPMENT DAMAGE FROM OVERHEATING

When the iPC is used under environmental conditions specified in as normal operation conditions in this manual, the temperature alarm should not activate.

Should a generation of the alarm occur during these normal environmental conditions, then the apparatus must have immediate repair or maintenance carried out.

Failure to follow this instruction can result in injury or equipment damage.

Refer to

Troubleshooting, p. 127 for more information

08/2006

61

Specific functions

LCD Backlight

Saver

Note: This function is only available on iPCs provided with pre-installed

Schneider–Electric software or been re-installed using the restoration software provided by Schneider–Electric.

This iPC is equipped with a function to save the LCD backlight lifetime. It is activated on a default setting to increase the useful lifespan of the fluorescent tubes.

The backlight saver can be found in the screen savers settings of Windows® under the heading SE_blank and is accessible from the desktop, "Right click" on the desktop, select "Properties" then "Screen Saver.

62

08/2006

Specific functions

Specific keys

At a Glance

Dual-function keys

On front panels with a keyboard, there are keys with a specific function. These are described below.

View of dual-function keys:

08/2006

The keys boxed in on the above illustration are dual-function keys.

Depending on the status of the ABC key, these keys either work as the function keys

F1 to F12 and the user function keys PF1 to PF20 , or as the alpha keys

QWERTYUIOP etc.

. The LED for the ABC key is lit when it is in the Alpha position.

63

Specific functions

Brightness control

The brightness of the LCD screen is adjusted in different ways depending on the type of front panel. The two types of adjustment are shown below.

View of brightness adjustment keys on MPC NT••• front panels

Increases brightness

Decreases brightness

View of brightness adjustment keys on MPC NA••• and MPC NB••• front panels

These keys are located on the number pad (to the right of the front panel).

To make an adjustment: z z

Hold down the

Hold down the

key, then press the key to increase the brightness

key, then press the key to decrease the brightness

64

08/2006

PF keys

Specific functions

Pressing a PFx key corresponds to pressing a sequence of keys. The key sequences are given below.

PF8

PF9

PF10

PF11

PF12

PF13

PF14

PF15

PF4

PF5

PF6

PF7

PF key

PF1

PF2

PF3

PF16

PF17

PF18

PF19

PF20

Sequence

CTRLL ALTL F1

CTRLL ALTL F2

CTRLL ALTL F3

CTRLL ALTL F4

CTRLL ALTL F5

CTRLL ALTL F6

CTRLL ALTL F7

CTRLL ALTL F8

CTRLL ALTL F9

CTRLL ALTL F10

CTRLL ALTL F11

CTRLL ALTL F12

CTRLL ALTL I

CTRLL ALTL M

CTRLL ALTL H

CTRLL ALTL A

CTRLL ALTL B

CTRLL ALTL C

CTRLL ALTL D

CTRLL ALTL F

Note: CTRLL = left "Ctrl" key, ALTL = left "Alt" key

08/2006

65

Specific functions

Touch-sensitive cursor

At a Glance

Description

Front panels with a keyboard feature a touch-sensitive cursor in the bottom righthand corner. It is described below.

View of the touch-sensitive cursor:

Cursor movement button

Left button Right button

66

08/2006

Specific functions

LED indicators

At a Glance

Meaning

On the front panel there are three LED indicators, the meanings of which are as follows.

Indicator Description

ON This is lit when the computer is powered-up

DISK

LAN

This shows when read/write operations are being performed on the hard disk

This shows when data is being exchanged on the built-in Ethernet link

08/2006

67

Specific functions

Control drawing of the PS/2 outlet on the Magelis iPC front panels

Introduction

Description

The following information concerns the use of the PS/2 outlet located on the front panels of the Magelis iPC used in Class I, Division 2 Groups A, B, C and D hazardous locations.

Information taken from the Schneider Electric document: 35007197P07000.

MPC••••••••••Model Mouse/Keyboard

Description of PS/2 pinouts:

1. Data

2. Not Connected

3. GND

4. VCC (see Note 1 for details)

5. CLK

6. Not Connected

4

6

2 1

5

3

The equipment used with nonincendive cabling

Notes:

Note

1

2

Description

Non-incendive circuit parameters: z PS/2 port: z z z z

Voc = 5.1 V

Isc = 5.5 A

Ca = 175

μ

F

La = 1.5

μ

H

The equipment used with non-incendive cabling must comply with the following requirements:

Apparatus used with non-incendive cabling (mouse, keyboard)

Industrial PC MPC•••••••••• model

Voc

Isc

Ca

La

≤ Vmax:

≤

Imax:

≤ Ci + C cable

≤ Li + L cable

68

08/2006

Specific functions

4

5

Note

3

Description z z

If the electrical parameters of the cable are not known, the following values should be used:

Capacitance 60 pF/ft

Inductive - 0.20

μ

H/ft

The non-incendive cabling must be installed in compliance with Article 501.4(B)(3) of the National Electrical Code ANSI/NFPA 70.

The apparatus used with non-incendive cabling must not contain or be connected to another power source.

Installation of Kit MPC YN0 0HLK 20N for Class I, Division 2 Hazardous

Locations.

Warning The MPC YN0 0HLK 20N kit is intended for use in Class I, Division 2 Groups A, B,

C, and D

It is used exclusively on AC 115/230 V 50/60 Hz Magelis Modular iPC Control Boxes reference MPC DN ** * A *, MPC EN ** * A *.

WARNING

EXPLOSION HAZARD

In Class I, Division 2 hazardous locations, The Magelis iPC must be wired according to the National Electric Code and/or Canadian Electric code as it applies to hazardous locations. Refer to the General Safety Information of the Magelis iPC external screen monitor User Manual.

Failure to follow this instruction can result in death, serious injury, or equipment damage.

Package contents

The shipping carton contains the following items: z z z z power cable retainer bracket for Control Box with 4 mounting screws spare parts screw bag with power cable, the user manual.

08/2006

69

Specific functions

Installing your

Magelis Modular iPC in a Class I,

Division 2

Hazardous

Location.

z z z z

Prepare the plug-less end of the AC power cable as follows: z If needed, cut the power cable to the desired length.

z z

Strip 2.5 in (60 mm) of the cable sheath,

Strip 1/4 in (6 mm) of insulation from the end of the 3 conductor wires, z Crimp a terminal to the stripped wire ends to keep the copper strands from fraying.

Connect the molded end of the cable to the mating connector on the side of the

Magelis iPC.

Operate the mains switch of the Magelis iPC in ON position.

Secure the power cable by mounting the cable retainer bracket on the Control

Box. See

Cable Retainer Bracket Mounting, p. 70.

WARNING

EXPLOSION HAZARD

Install the retainer bracket for hazardous locations. The bracket secures the cable from accidental disconnection. Do not operate the AC power switch since it is an arcing device.

Failure to follow this instruction can result in death, serious injury, or equipment damage.

To connect the Magelis iPC to the power supply: z z z z

Turn off the main switch or breaker,

First connect the ground wire (green wire) to the terminal block of the cabinet with the right tightening torque,

Then connect the remaining two wires (Live: black wire and Neutral: white wire),

Restore the AC power for start.

Cable Retainer

Bracket

Mounting

The chart below describes installation of the feeding cable retainer bracket:

Illustration Description z z z z

Remove the 4 screws indicated by the arrows,

Connect the power cable,

Operate power switch to ON position,

Place the retainer bracket and fasten with the screws (indicated by the arrows).

70

08/2006

Specific functions

08/2006

71

Specific functions

72

08/2006

Recommendations

At a Glance

Subject of this part

What's in this

Part?

This part concerns recommendations

This part contains the following chapters:

Chapter

6

Chapter Name

Recommendations

II

Page

75

08/2006

73

Recommendation

74

08/2006

Recommendations

6

At a Glance

Recommendations

What's in this

Chapter?

This cahpter provides details of Schneider–Electric recommendations

This chapter contains the following topics:

Topic

Integration of the iPC and Front Panel

Environmental conditions

Page

76

77

08/2006

75

Recommendations

Integration of the iPC and Front Panel

Mechanical assembly

Axis

This apparatus is intended to be used in a box or cabinet, insuring mechanical protection and compliance of environmental specifications of the iPC.

The following general principles are to be adhered to: z Conform to documentation and use the adapted accessories z Use only the supplied fixings for attaching the Front panel z When mounting the front panel in a rack, the Front panel rack mount kit is to be used (MPC YN0 0NNN 00N (sold separately)).

z The iPC must be assembled according to specified horizontal or vertical axis.

There is no preferential direction but, it is necessary to take account of final accessibility for the exploitation or maintenance (access to disk drive, CD reader.Combo drive) Any assembly according to an oblique direction is prohibited.

z To maintain the sealing characteristics of the product, the cut out dimensions corresponding to the screen must conform to the dimensions indicated in this document.

Electrical wiring z Use high quality shielded cables for low current wiring.

z Keep separate the wiring for low current and high current (networking, peripherals and power etc.) It is mandatory that the ground wiring be made of a star connection to keep the circuits separate.

z All moveable metal elements must be connected to protective ground using sufficient braided section (doors, drawers etc.) z Insure that all cables are securely attached to avoid disconnection and degradation of the contacts.

z Select a breaker that is capable of handling the inrush current when powering on the iPC.

76

08/2006

Recommendations

Environmental conditions

Temperature warning

The acceptable maximum ambient temperature of the iPC is 50 °C. This temperature is measured around the immediate proximity of the apparatus.

Measurement or checking the temperature must be undertaken on a configuration of a minimum of 1 hours operation and in an environment itself stable in temperature.

The temperature is a principle of the following parameters: z Ambient temperature of the room or where the installation is located z Thermal characteristics of the cabinet z Ventilation or air conditioning (if any) of the cabinet z Power dissipated by all the equipment located within the cabinet z Condition of the iPC dust protection filters z Continual use of the CD/Combo drive may have an adverse affect on the iPC ambient temperature.

Schneider–Electric recommend as far as it is possible, that when setting out the devices in the cabinet, that the devices dissipating the most heat be placed at the top of the cabinet. This method is vital when using a cabinet with no ventilation.

Should the iPC temperature alarm go into alarm, it is necessary to analyze all of the system parameters to determine which parameter/s may be initiating the alarm.

Note: This state is destructive if no immediate action is taken.

08/2006

77

Recommendations

Waterproof

Sealing

The front panel of the iPC conforms to IP65 and NEMA 4 (sealing resistance of a water jet). However, the control box conforms to IP20 (no water or dust tight sealing resistance), so the cabinet or box must provide this function for protection of the iPC.

Routine inspection of all the seals (Joints, filters, passage of cables etc.) is essential.

It is also recommended to periodically clean the magneto-optical peripherals (CD/

Combo and floppy drives), using any of the range of cleaning kits available commercially.

Note: The term dust being introduced into the cabinet or box refers to the following consequences: z Blocking of the dust protection filters resulting in a consequent rise in temperature z Failure of the magneto-optical peripherals (CD/DVD-ROM, floppy disk etc.) z Random breakdowns from metal dust or metallic oxides.

Shocks and

Vibrations

The iPC contains elements sensitive to shocks and vibrations (hard disk drive

PCMCIA cards, external cables etc.) This product has been designed especially for applications requiring particular high a immunity but, basic principles must still be followed.

z The iPC must be assembled in the cabinet in a perfectly rigid way in order not to amplify the external mechanical disturbances z The whole body of the cabinet itself must be perfectly rigid in structure. In particular when the iPC is assembled on the door of the cabinet, the structure must be sufficiently rigid (especially around its closing system and hinges) otherwise it may be necessary to add stiffeners.

z The cabinet must be firmly stood or attached securely to the ground.

z If the cabinets are installed in nonrigid places, by nature (metal footbridges etc.), then they must be fixed to a rigid structure of the building.

78

08/2006

Power Supply

Uninterrupted

Power Supply

Recommendations

The basic rules of wiring must be complied with: z Do not power the iPC on a source that will cause major disturbances. (i.e. welders or generators).

z The iPC is protected from short power cuts (10 ms AC). However, any longer power cuts including ones forced by the operator can generate corruptions on the files stored on the hard disk or on external storage of a system file (PCMCIA,

USB). If the iPC shuts down while writing these files, in certain circumstances, the system files may become corrupt and the system will not restart with out a complete reinstallation of the iPC software.

z The data must be regularly safeguarded.

z Shutting down the iPC before the Windows operating system has properly shut down can cause unforeseen faults in the operating system.

z If there is a risk of unforeseeable power interruptions, Schneider–Electric recommend the use of an Uninterrupted Power Supply (UPS). Refer to

Uninterrupted Power Supply, p. 79 for more details.

z If certain files become corrupted, the utility "Scandisk" provided by Microsoft makes it possible in certain cases to repair these files. Refer to the document provided by Microsoft for instruction on how to do this. However should the files be unrecoverable only the use of the restoration tool supplied with the iPC will allow for reinstallation of the iPC. In this case, all files present on the hard disk will be lost.

When selecting a UPS, it is imperative that the model chosen uses technology based on double conversion. Only this architecture ensures a total transparency at the time of the loss of the principal network and does not generate interruption.

Other existing technologies are all based on a communication between the principal network and a backed up output. This communication not only generates a longer interruption but may also generate disturbances on the network of several thousand volts, all at the same time, which may cause destruction of the iPC.

It is advisable to choose a UPS supplied with a driver compatible with the operating system of the iPC. In effect only this function allows stopping the system correctly in all cases.

A good example is the Extreme model Pulsar 700C (MGE UPS Systems). This example is compatible with all AC supplied iPC.

08/2006

79

Recommendations

Shut down iPC When powering down the iPC it is highly recommended to follow strictly the shutdown procedure provided by the operating system.

Due to the PC architecture, the Hard Disk may accidentally become corrupted if the machine is powered off without adhering to the shutdown procedure dependent upon the operating system used.

The main possible consequences of an abnormal power off are: z Data becomes corrupted inside the Hard Disk; leading to possible loss of data.

z Sectors definitely damaged and reallocated; leading to fast deterioration of the

Hard Disk.

80

08/2006

Installation

At a Glance

Subject of this part

What's in this

Part?

This part concerns product installation.

This part contains the following chapters:

Chapter

7

8

9

10

Chapter Name

Dimensions/Assembly

Getting started

Configuration of the Bios

Hardware extensions

III

Page

83

99

101

109

08/2006

81

Installation

82

08/2006

Dimensions/Assembly

7

At a Glance

Subject of this chapter

What's in this

Chapter?

This chapter concerns the dimensions and the panel mounting of products.

This chapter contains the following topics:

Topic

Dimensions of the Front Panels

Other dimensions

Cut out dimensions for cabinet installation

Panel mounting

Mounting in 19" rack

Mounting without a front panel

Assembly of the front panel onto the Control Box

Mains supply of the Control Boxes

Direct current supply of Control Boxes

Page

84

85

87

88

89

91

92

94

95

08/2006

83

Dimensions/Assembly

Dimensions of the Front Panels

At a Glance The dimensions of the two types of 15’’ front panels are provided below.

Dimensions of the Front Panels

Front panels with touch sensitive screen: mm (in.)

460 (18.11)

Front panels with keyboard: mm (in.)

480 (18.90)

84

08/2006

Dimensions/Assembly

Other dimensions

At a Glance

MPC EN•••

The dimensions of the products equipped with a front panel are provided below.

With a 15" touch-sensitive screen front panel: MPC NT50 •• mm (in.)

440 (17.32) 155

(6.10)

316 (12.44)

8

(0.37)

316 (12.44)

With a 15" screen front panel (touch-sensitive or non-touch-sensitive) and keyboard:

MPC NA50 •• or MPC NB50 •• mm (in.)

450 (17.72)

155

(6.10)

316 (12.44)

316 (12.44)

8

(0.37)

08/2006

85

Dimensions/Assembly

MPC DN••• With a 15" touch-sensitive screen front panel: MPC NT50 •• mm (in.)

440 (17.32) 212 (8.35)

316 (12.44) 8

(0.37)

316 (12.44)

With a 15" screen front panel (touch-sensitive or non-touch-sensitive) and keyboard:

MPC NA50 •• or MPC NB50 •• mm (in.)

450 (17.72) 212 (8.35)

316 (12.44)

8

(0.37)

316 (12.44)

86

08/2006

Dimensions/Assembly

Cut out dimensions for cabinet installation

At a Glance

15" screen without keyboard

For cabinet installations, it is necessary to create a cut out in the enclosure for mounting. The dimensions of the cut out to be performed, depends upon the type of front panel used.

Cut out dimensions mm in.

15" screen with keyboard

Cut out dimensions mm in.

442

17.4

452

17.8

08/2006

87

Dimensions/Assembly

Panel mounting

At a Glance

Illustration

The products and their front panels are designed to be attached to any flat surface.

Products can be mounted as described below.

Attachments*

Seal

*Affix the MPC to the panel using the attachments as shown.

88

08/2006

Dimensions/Assembly

Mounting in 19" rack

Introduction A front panel with 15" screen can be mounted in a 19" rack. This mounting uses brackets available in the catalogue (Ref. no. MPC YN00 RMK 00N ).

View of a front panel mounted in a 19" rack:

Mounting View of a front panel mounted using attachment brackets

Attachment

Brackets

08/2006

89

Dimensions/Assembly

Mounting recommendations

To facilitate the insertion of a CD/Combo drive and a diskette, the support used must be no thicker than 63 mm ( 2.5 in.) see figures below:

Overhead view: mm in.

63

2.48

CD-ROM/Combo drive

Back view: mm in.

CD-ROM/Combo drive

63

2.48

90

08/2006

Dimensions/Assembly

Mounting without a front panel

At a Glance

Mounting

It is possible to use a Control Box with a video monitor and external keyboard instead of a front panel. Here, Control Box Mounting Plate MPC NP00 NNN 00N is used as an attachment and front panel connector cover.

View of a Control Box mounted on a Telequick AM1 PA plate:

08/2006

Procedure:

Step

1

2

Action

Assemble the Control Box connection base using the 12 cross-slot screws supplied.

Attach the assembly to the plate using the four screws

91

Dimensions/Assembly

Assembly of the front panel onto the Control Box

At a Glance If you are using one of the computers in the range with a MPC NT••, MPC NA•• or

MPC NB•• type front panel, you must first assemble this front panel onto the Control-

Box. These operations must be performed with the power switched off .

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH z The mains plug on this equipment must be used to disconnect the mains power.

z Remove all power before removing any covers or elements of the system and installing or removing any hardware and cables. Insure that the area is nonhazardous.

z Always use a properly rated voltage sensing device to confirm power is off.

z Wait 10 minutes before removing covers.

z Replace and secure all covers or elements of the system before applying power to the unit.

Failure to follow this instruction will result in death or serious injury.

92

08/2006

Procedure

Dimensions/Assembly

In order to assemble the two sections, use a Pozidriv cross-slot screwdriver and follow the instructions below:

Step

1

Action

Assemble the Control-Box onto the front panel using the 4 alignment studs located at the rear of the front panel

Control-Box

4 alignment studs

Front panel

2 Fasten the assembly at all points around the Control Box, using the 12 crossslot screws supplied

12 cross-slot screws

Control-Box

Front panel

08/2006

93

Dimensions/Assembly

Mains supply of the Control Boxes

At a Glance Alternating Current versions of the Control Boxes are connected to the mains using the lead supplied.

Note: : The mains supply modules for the Control Boxes are fitted with a protection fuse as standard. This fuse is located inside the module but cannot be accessed.

Note: The MPC EN•• and supply module of the MPC DN•• are equipped with a

3.15 A time-delayed fuse located in the mains input connector. Only replace the fuse with a fuse of the same ratings.

94

08/2006

Dimensions/Assembly

Direct current supply of Control Boxes

At a Glance Direct current versions of the Control Boxes connect to a 24 VDC supply (see

Control Box specifications, p. 42).

Note: Don’t use direct current Control Box supplies featuring a strong inrush current on a direct current network with a fold back current limitation protection.

When a supply module is connected to a direct current network, limit the length of the supply cable, to prevent line losses: z Supply of an MPC EN••• or MPC DN•••: z Length limited to 30 m/90 ft (60 m/ 180 ft 'round-trip') with 2.5 mm

2

/AWG 14 section copper wires z Length limited to 20 m/60 ft (40 m/120 ft 'round-trip') with 1.5 mm

2

/AWG 16 section copper wires

08/2006

95

Dimensions/Assembly

Possible connections

Connection of a Magelis iPC supplied by a non-grounded safety DC network:

The 0 V and mechanical ground are connected internally inside the front panels and

Control-Boxes, as well as in the network cabling accessories.

Specific connection measures are to be taken for specific applications that use a floating network. These depend on the chosen mode of installation.

In these cases, the 24 VDC input of the Control Box supplies is isolated in relation to the outputs and mechanical ground: z z

Primary/Secondary dielectric strength: z MPC EN•/DN• : 500 VAC

Primary/Ground dielectric strength: z MPC EN•/DN• : 500 VAC

Connection of a 24 VDC Magelis iPC using a floating direct current network:

Circuit diagram

Low voltage

AC network

Magelis iPC

Battery charger

+

-

+

-

Battery

Isolation controller

Floating 24 VDC network

-0 V

+24 V

96

08/2006

Dimensions/Assembly

Connection of a 24 VDC Magelis iPC using a ground referenced network:

115-230 VAC network

L

N

Q

PE

KM

(2)

~

- +

+24/-

48 VDC

(1)

(1)

Sensor/actuator/PLC supply

Q: General isolator

KM:Line contactor or circuit breaker

(1) : Isolation strip for detecting grounding faults

(2) : possibility of using a TSX SUP••• power supply

+

-

Magelis iPC

Note: Protection fuse : the 24 VDC mains supply modules for the Control Boxes are fitted with a protection fuse as standard. This fuse, fitted in series with the

24 VDC input, is located inside the module but cannot be accessed.

Terminal block View of the connection terminal block:

08/2006

+24V -24V GND

Alarm

θ

Power DC

FG is the ground connection. It is connected to the mechanical ground of the Control

Box.

Tightening torque of the terminal block screws: 1 Nm/8.85 lbin .

97

Dimensions/Assembly

98

08/2006

Getting started

8

First power-up

Seal removal

Note: Before the first power-up, please read the "LIMITED USE LICENSE

AGREEMENT" carefully, then remove the seal.

Preparation On first power-up, it is necessary, depending on the software configuration of your

MPC••, to perform the following operations: z z

Customization and parametering of the operating system

Installation, customization and parametering of Schneider Automation and

Schneider Electric applications (Vijeo Look)

For these different operations, refer to the "MPC installation guide" (ref. 35012231).

99

08/2006

Getting started

100

08/2006

Configuration of the Bios

9

At a Glance

What's in this

Chapter?

What's in this

Chapter?

This chapter describes how to access certain parameters of the Bios (operating system of the computer) that need to be modified depending on its existing configuration.

This chapter contains the following topics:

Topic

Accessing the BIOS configuration

Configuration screens

Modifying the date and time

Modifying the User password

Page

102

103

105

106

101

08/2006

Configuration of the Bios

Accessing the BIOS configuration

Procedure In order to access the configuration screen, follow the instructions below:

Step

1

2

3

Action

Power-up or restart the computer by pressing Ctrl+Alt+Del simultaneously

When the message "Press Del to enter Setup" appears, press Del

The configuration screen is displayed

Illustration BIOS configuration welcome screen:

Phoenix - AwardBIOS CMOS Setup Utility

Standard CMOS Features

Advanced BIOS Features

Advanced Chipset Features

Integrated Peripherals

Power Management Setup

PnP/PCI Configurations

PC Health Status

Esc: Quit

F10: SAVE & EXIT SETUP

Frequency/Voltage Control

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

Set User Password

Save & Exit Setup

Exit Without Saving

: Select Item

Time, Date, Hard Disk Type ...

102

08/2006

Configuration of the Bios

Configuration screens

General 14 headings are available from the welcome screen.

z Use the 4 arrow keys to move from one heading to another z z z

The ESC key is used to quit configuration mode

The F10 function key is used to save modifications and quit configuration mode

The keys Shift+F2 are used to modify the color of the screens

08/2006

103

Configuration of the Bios

Headings Description of the different headings:

Heading

Advanced BIOS Features

Description

Standard CMOS Features This is used to modify the standard parameters in the CMOS memory, such as the date, time and display.

This is used to modify the characteristics of the Bios. We strongly recommend that you do not modify these values.

Advanced Chipset Features This is used to modify the characteristics of the Chipset.

We strongly recommend that you do not modify these values.

Integrated Peripherals This is used to modify the parameters of internal peripherals.

We strongly recommend that you do not modify these values.

Power Management Setup This is used to modify the power saving mode for the power supply, hard drive and video.

We strongly recommend that you do not modify these values.

PnP/PCI Configurations This is used to configure the PCI bus.

We strongly recommend that you do not modify these values.

PC Health Status This is used to modify the CPU’s clock and voltage.

Frequency/Voltage Control This is used to display CPU/System temperature, Fan speed.

Load Fail-Safe Defaults

Load Optimized Defaults

This is used to restore the Bios parameters to factory values

(for example to restart with stable values in the event of problems).

This is used to restore the parameters of the Bios with optimized values.

Set Supervisor Password

Set User Password

Save & Exit Setup

Exit without Saving

This is used to enter a password in order to access the Bios configuration.

This is used to define a user password for the machine.

This is used to save modifications in the CMOS memory and to quit the Bios configuration.

This is used to quit configuration without saving the modifications made.

Note: The remainder of this chapter describes the screens that may be modified during general use of the equipment. Any higher level screens may only be modified by an approved Schneider Technician.

104

08/2006

Configuration of the Bios

Modifying the date and time

At a Glance The date and time stored in the computer can be adjusted from the Standard CMOS

Features screen of the Bios configuration utility.

View of the screen:

Phoenix - AwardBIOS CMOS Setup Utility

Standard CMOS Features.

Item Help Date (mm:dd:yy)

Time (hh:mm:ss)

IDE Primary Master

IDE Primary Slave

Drive A

Drive B

Video

Halt On

Base Memory

Extended Memory

Total Memory

Sun, Apr 27 2005

12 : 45 : 53

[ O H B K 0 3 A ]

[CD-224E]

[1.44M, 3.5 in. ]

[None]

[EGA/VGA]

[All , but Keyboard]

648K

228652K

229376K

Menu Level

Change the day, month, year and century

Procedure

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

The procedure for modifying the time and date of the PC is as follows:

Step

1

Action

Use the arrow keys to select the date or time of the PC

2

3

4

Modify the value using the PageUp and PageDown keys

Use the ESC key to quit the modification mode and return to the welcome screen

Save the modifications by pressing F10 .

08/2006

105

Configuration of the Bios

Modifying the User password

At a Glance The user password can be modified from the Bios configuration welcome screen.

Note: The password can be assigned either when the computer is started

(System), or when the Bios is modified (Setup). This option can be chosen by selecting Security Option in the Advanced BIOS Features screen.

In order for the password to be active on start-up, you must select the option

System . The default option ( Setup ) only asks for the password to access the Bios configuration.

View of the screen:

Standard CMOS Features

Advanced BIOS Features

Advanced Chipset Features

Integrated Peripherals

Power Management Setup

PnP/PCI Configurations

PC Health Status

Esc: Quit

F10: SAVE & EXIT SETUP

Phoenix - AwardBIOS CMOS Setup Utility

Frequency/Voltage Control

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

Set User Password

Save & Exit Setup

Exit Without Saving

: Select Item

Change/Sel/Disable Password

106

08/2006

Procedure

Configuration of the Bios

The password modification procedure is as follows:

Step

1

Action

The following box is displayed:

ENTER PASSWORD:

2

Note: if you no longer require a password, simply press Enter

Enter your password and press Enter

The following box is displayed:

CONFIRM PASSWORD:

3

4

Enter your password again and press Enter

Press F10 to save and quit

08/2006

107

Configuration of the Bios

108

08/2006

Hardware extensions

10

At a Glance

Subject of this chapter

This chapter concerns the hardware extensions for the Magelis iPC range of industrial PCs.

DANGER

HAZARDOUS VOLTAGE

Remove all power before removing any covers or elements of the system and installing or removing any hardware and cables. Insure that the area is nonhazardous.

Always use a properly rated voltage sensing device to confirm power is off.

Wait 10 minutes before removing covers.

Replace and secure all covers or elements of the system before applying power to the unit.

Failure to follow this instruction will result in death or serious injury.

What's in this

Chapter?

This chapter contains the following topics:

Topic

Removing/inserting the Hard Disk drive CD-RW/DVD-R drive

Disassembling the modules

Installing an extension card for MPC DN••

Installing an extension card for MPC EN••

Adding a memory extension card

Page

110

111

113

116

118

109

08/2006

Hardware extensions

Removing/inserting the Hard Disk drive CD-RW/DVD-R drive

At a Glance Removable Hard Disk drive and CD-ROM are installed in the MPC EN••• and MPC

DN••• Control Boxes. The procedure for removing and inserting the drives is given below.

Note: When the CD-RW/DVD-R is not installed in the unit, a cover plate (supplied initially with the iPC and as part of Maintenance Kit MPC YN5 TMNT KT2 or MPC

YN5 KMNT KT2 should be used to help prevent dust entering the unit.

Removing the drive

The removal procedure for the drive is as follows:

Step

1

2

3

Action

Disconnect the power to the computer

Unscrew the two fastening screws of the drive

Remove the drive from its housing by gently pulling it towards you using the fastening screws

Inserting the drive

The insertion procedure for the drive is as follows:

Step

1

2

3

Action

Disconnect the power to the computer

Position the drive in its housing and gently push it in until the stop is reached

Tighten the fastening screws alternately

110

08/2006

Hardware extensions

Disassembling the modules

At a Glance

Power supply module

In order to maintain the MPC DN•• products, it is possible to replace the power supply module and extension card module. The procedure is as follows.

Disassembly/Reassembly:

Step

1

2

Action

Disconnect the supply lead

Unscrew the four fastening screws at the rear of the MPC

Power supply module

Extension module

3 Remove the power supply module

08/2006

4 To reassemble the module, perform the above operations in the reverse order using the alignment studs

Note : For MPC DN•• products, it is necessary to link the power supply block to the extension card block with a connector

111

Hardware extensions

Extension module

Disassembly/Reassembly:

Step

1

2

3

Action

Disconnect the supply lead

To access the extension module you must: first remove the power supply module

Unscrew the four fastening screws at the rear of the MPC extension block using a cross-slot screwdriver

Power supply module

Extension module

4 Remove the extension module

112

5 To reassemble the module, first replace the extension card block, then the power supply block

08/2006

Hardware extensions

Installing an extension card for MPC DN••

At a Glance

Installation

The MPC DN•• Control Box features a compartment for PCI-format extension cards.

The procedure for installing a card is given below.

In order to install an extension card, use a Pozidriv cross-slot screwdriver and follow the steps described below:

Step

1

2

Action

Disconnect the power to the computer

Unscrew the four knurled screws located under the Control Box in order to remove the cover of the hatch giving access to the extension card slots

3

4

4 knurled screws

Select a PCI slot

Unscrew the cable plate screw and remove

Screw and cable plate

08/2006

113

Hardware extensions

Step

5

Action

Unscrew the two fastening screws from the extension card retaining bracket that correspond to the selected slot, release from the oblongs and remove.

Holding parts

Oblongs

6

7

Fastening screw

Place the card in its connector until the stop is reached

Attach the front panel of the card to the Control Box using the screw

Screw

114

08/2006

08/2006

Step

8

Hardware extensions

Action

Replace the holding part of the card so that it comes into contact with the top of the extension card, thus preventing the card from coming away from its connector. Position the moving part to suit the length of the card, and to facilitate access to its functions, where necessary. Then tighten the screw on the moving part, then the fastening screws.

Moving part

Oblongs

9

Enlarged view of the holding part

Screw Fastening screw

Replace the hatch cover and tighten the 4 knurled screws

115

Hardware extensions

Installing an extension card for MPC EN••

At a Glance

Installation

The MPC EN•• Control Box features a compartment for PCI-format extension cards.

The procedure for installing a card is given below.

In order to install an extension card, use a Pozidriv cross-slot screwdriver and follow the steps described below:

Step

1

2

Action

Disconnect the power to the computer

Unscrew the four knurled screws located under the Control Box in order to remove the cover of the hatch giving access to the extension card slots

3

4

4 knurled screws

Select a PCI slot

Unscrew the cable plate screw and remove

Screw and cable plate

116

08/2006

Step

5

Hardware extensions

Action

Unscrew the two fastening screws from the extension card retaining bracket that correspond to the selected slot, release from the oblongs and remove.

Holding parts

Oblongs

08/2006

6

7

Fastening screw

Place the card in its connector until the stop is reached

Attach the front panel of the card to the Control Box using the screw

8

Screw

Replace the holding part of the card so that it comes into contact with the top of the extension card, thus preventing the card from coming away from its connector. Position the moving part to suit the length of the card, and to facilitate access to its functions, where necessary. Then tighten the screw on the moving part, then the fastening screws.

Moving part

Oblongs

9

Enlarged view of the holding part

Screw Fastening screw

Replace the hatch cover and tighten the 4 knurled screws

117

Hardware extensions

Adding a memory extension card

At a Glance It is possible to increase the memory capacity of the Control Boxes. A memory card access hatch is provided for this purpose. The procedure for accessing the memory extension cards is provided below.

CAUTION

STATIC SENSITIVE COMPONENTS

Static electricity may destroy electronic components. Always handle cards by their edges, without touching the components or the conducting tracks.

Failure to follow this instruction can result in injury or equipment damage.

MPC EN••• The procedure for accessing memory extension cards is as follows:

Step

1

2

3

4

5

6

Action

Disconnect the power to the computer.

Unscrew the three cross-slot screws of the cover located at the rear of the computer.

Insert a memory extension card in a free slot, ensuring proper direction of insertion.

Secure the card in its slot by folding inwards the plastic fastening tabs located at each end.

Replace the rear cover by tightening the three cross-slot screws.

Power-up the computer and, when requested, press F1 to acknowledge the new configuration.

118

08/2006

MPC DN••

Hardware extensions

The procedure for accessing memory extension cards is as follows:

Step

1

2

3

4

5

6

7

8

Action

Disconnect the power to the computer.

Remove the supply block by unscrewing the four cross-slot screws and pulling it towards you (see

Disassembling the modules, p. 111 ).

You now have access to the memory card hatch.

Unscrew the three cross-slot screws in order to remove the cover of the memory slot hatch.

Insert a memory extension card in a free slot, ensuring proper direction of insertion.

Secure the card in its slot by folding inwards the plastic fastening tabs located at each end.

Replace the rear cover by tightening the three cross-slot screws.

Replace and tighten the screws of the power supply block.

Power-up the computer and, when requested, press F1 to acknowledge the new configuration.

08/2006

119

Hardware extensions

120

08/2006

Maintenance

IV

At a Glance

Subject of this part

What's in this

Part?

This part concerns the implementation of products.

This part contains the following chapters:

Chapter

11

Chapter Name

Maintenance

Page

123

08/2006

121

Maintenance

122

08/2006

Maintenance

11

At a Glance

Subject of this chapter

What's in this

Chapter?

This chapter covers maintenance of the computers from the Magelis iPC range.

This chapter contains the following topics:

Topic

Reinstallation

Replacing dust filters for MPC DN••

Replacing dust filters for MPC EN••

Troubleshooting

Page

124

125

126

127

123

08/2006

Maintenance

Reinstallation

At a Glance

Before reinstalling

In certain cases, it may be necessary to reinstall the operating system. The reinstallation procedure is given below.

Before reinstalling the operating system, make sure that the following equipment is at hand: z z

A CD-RW/DVD-R drive, (Ref. MPC YN00 CDWR ROM ),

The reinstallation CD-RW/DVD-R that was provided with the product

Note: :The reinstallation process erases all data on the hard drive. Back up all important data contained on the hard drive prior to reinstalling the operating system. The reinstallation process will return the computer to its factory settings.

Reinstallation

Specific drivers

Refer to Magelis iPC installation Guide. (ref 35012231)

Specific drivers are available on the reinstallation CD-RW/DVD-R. These drivers are already installed on your machine and should not need to be reinstalled.

124

08/2006

Maintenance

Replacing dust filters for MPC DN••

At a Glance

Accessing the filters

It is necessary to regularly check the condition of the Control Boxes' dust filters, in order to clean or change them if they are very dirty.

Note: The frequency of replacing the filters depends entirely upon the pollution levels at installation location.

Spare filters are included in the maintenance kit MPC YN5 TMNT KT or MPC YN5

KMNT KT2

View of the filters' location:

08/2006

Lever off the outer cover (pictured left) to gain access to the filter pad. Once filter is replaced firmly push the outer cover until it clicks back into place.

Remove the outer cover by gripping firmly and pulling off. Once the filter is replaced push the outer cover until it clicks back into place.

Note: Only the outer cover is removed.

125

Maintenance

Replacing dust filters for MPC EN••

At a Glance It is necessary to regularly check the condition of the Control Boxes' dust filters, in order to clean or change them if they are very dirty.

Note: The frequency of replacing the filters depends entirely upon the pollution levels at installation location.

Accessing the filters

View of the filters' location:

126

Lever off the outer cover to gain access to the filter pad. Once filter is replaced firmly push the outer cover until it clicks back into place.

Note: Only the outer cover is removed.

08/2006

Maintenance

Troubleshooting

First Level

Checks

In the event of problems, the following table details basic problem solving and first level corresponding checking.

Encountered Problem

Failure of the iPC (Fans do not function)

The internal buzzer emits beeps during power up

Failure of the LCD screen

Corresponding Checking

Check power supply is present and the state of the protection fuse (AC only)

Check RAM is correctly installed

Temperature alarm initiates

Check the operation of the iPC and video by using an external monitor on the VGA connector

Check the operation of the iPC fans. Check and clean the dust protection filters. Check the sealing and ventilation of the cabinet

The index reliability of the hard disk is lower than 20%

The index reliability of the hard disk decreases rapidly

Errors reading or writing to diskettes

Replace the hard disk at the first given opportunity

Check the rigidity and stability of the cabinet.

Remove the cause of shocks or vibrations

Errors reading from CD or DVD

Random operating problems

Use certified diskettes. Clean the head of the disk drive

Clean the heads of the CD or DVD reader

Check the environment conformity of the iPC: z Temperature

Windows will not start z Dust z Power supply z Shocks and vibrations

Repair the corrupted files (Scandisk).

Restore the operating system (Restore CD).

Check the power supply. Shut down

Windows correctly using the Shutdown procedure. Consider the use of a UPS

08/2006

127

Maintenance

128

08/2006

V

Appendices

At a Glance

Subject of this part

What's in this

Part?

This part contains the appendices relating to the products.

This part contains the following chapters:

Chapter

12

Chapter Name

Accessories

Page

131

08/2006

129

Appendices

130

08/2006

Accessories

12

Accessories

List Accessories are available as options. The list of accessories are shown below:

Description

External industrial PS/2 keyboard

RAM 512 MB

RAM 1024 MB

Front panel rack mount kit

Control Box Mounting Plate

Maintenance kit for 15T

Maintenance kit for 15K & KT

CD-ROM writer/DVD ROM reader

Power supply AC for MPC DN

Power supply DC for MPC EN

Removable HDD

Hazardous location kit

Reference

MPC YN0 0KBD 00N

MPC YDE RAM0 512

MPC YDE RAM1 024

MPC YN0 0RMK 00N

MPC NP0 0NNN 00N

MPC TN5 TMNT KT2

MPC YN5 KMNT KT2

MPC YN0 0CDW ROM

MPC YN0 0PWS AC4

MPC YN0 0PWS DC4

MPC NY0 0SFW 20N

MPC YN0 0HLK 20N

131

08/2006

Accessories

132

08/2006

Index

A

accessing BIOS, 102

Accessories, 131

adding memory extension card

MPC DN, 119

MPC EN, 118

assembling front panels to control boxes, 92

B

backlight saver, 62

C

configuration screens, 103

connector block

alarm temperature, 58

control box

MPC DN, 33

MPC EN, 35

D

dImensions

MPC DN, 86

MPC EN, 85

dimensions

15" screen with keyboard cut out, 87

15" screen without keyboard cut out, 87

front panels, 84

08/2006

A C disassembly

extension module, 112

power supply module, 111

E

environmental characteristics, 48

extension card installation

MPC DN, 113

MPC EN, 116

F

Front Panel Mounting, 88

H

hazardous location kit

cable retainer bracket, 70 installation, 70

HDD index reliability, 56

I

inserting drives, 110

L

LED indicators, 67

133

Index limitations

CD reader, 49 combo drive, 49

PCMCIA cards, 49

USB interfaces, 49

lithium battery, 27

M

modifying date and time, 105

Mounting in 19" Rack, 89

mounting without front panel, 91

P

password modification, 106

power supply

alternating current, 94

direc current (DC), 95

R

reassembly

extension module, 112

reassemly

power supply module, 111

recommendations

environmental conditions, 77

integration of iPC and front panel, 76

removing drives, 110

replacing dust filters

MPC DN, 125

MPC EN, 126

S

specific keys

brightness control, 64

dual function keys, 63

PF keys, 65

specifications

front panels, 47

MPC DN, 43

MPC EN, 45

134

T

temperature

events recording, 59

monitoring, 57

terminal block, 97

troubleshooting, 127

08/2006