Advertisement
Advertisement
MAGELIS iPC
Industrial PCs
User manual
eng
2
Table of Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
About the Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Part I
General overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Chapter 1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Chapter 2
Physical overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.1
2.2
Chapter 3
Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3.1
3.2
3.3
Chapter 4
Specific functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
3
4
Control drawing of the PS/2 outlet on the Magelis iPC front panels . . . . . . . . . . 55
Installation of Kit MPCYN00HLK00N for Class I, Division 2 Hazardous Locations.
Part II
Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Chapter 5
Assembly and connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Assembly of the front panel onto the Control Box . . . . . . . . . . . . . . . . . . . . . . . . 64
Chapter 6
Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Chapter 7
Hardware extensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Removing/inserting the CD-ROM and diskette drive . . . . . . . . . . . . . . . . . . . . . . 72
Chapter 8
Configuration of the Bios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Chapter 9
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Part III
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Chapter 10
Dimensions/Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Chapter 11
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Part IV Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Chapter 12
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
5
6
Safety Information
§
General safety information for users
General The present documentation is aimed at qualified technical personnel responsible for the implementation, operation and maintenance of the products described. It contains the information necessary for compliance with the proper use of the products. However, those who wish to make more "advanced" use of our products may find it necessary to consult our nearest distributor in order to obtain additional information.
The contents of this documentation are not contractual, and in no way constitutes an extension to, or restriction of, the contractual warranty clauses.
WARNING
The different elements of this unit must be completely assembled before power-up.
Failure to follow this precaution can result in death, serious injury, or equipment damage.
7
Safety Information
Personnel qualifications
Compliance of use
Only qualified personnel are authorized to implement, operate or maintain the products. The interference of non-qualified persons or failure to observe the security instructions contained in this manual, or attached to the devices, can endanger the personnel and/or do irreparable damage to the equipment. The following persons can be designated as " qualified personnel ": l l at application design level, engineering department personnel who are familiar with automation safety concepts (for example, a design engineer), at equipment implementation level, personnel who are familiar with the installation, connection and commissioning of automation equipment (for example, an installation assembly or cabling engineer, or a commissioning technician), l l at operation level, personnel who are experienced in the use and control of automation equipment (for example, an operator), as far as preventive or corrective maintenance is concerned, persons trained and qualified in regulating or repairing automatic devices (for example an operating technician, or an after-sales service technician, etc.).
The products described in the present documentation comply with the European
Directives* to which they are subject (EC marking). However, these can only be used correctly if in applications for which they are specifically intended, as specified in the relevant documentation, and in connection with approved third-party products.
As a general rule, correct usage of the products, with no danger to personnel or hardware, consists of complying with all handling, transport and storage recommendations, and all installation, operation and maintenance instructions.
* EMCD and LVD directives concerning Electromagnetic Compatibility and Low
Voltage.
Replacement and recycling of used batteries
Replace batteries with those of the same type, and dispose of any defective batteries in the same way as toxic waste.
Lithium or mercury batteries must not be thrown into a fire, opened, recharged or welded.
8
Lithium battery
Safety Information
The terminal contains a lithium battery, which is used to save certain data such as the date and time.
This must only be replaced by a qualified technician.
WARNING
Non-compliance with this warning may lead to a risk of explosion!
Failure to follow this precaution can result in death, serious injury, or equipment damage.
Federal
Communications
Commission
Radio Frequency
Interference
Statement - For
U.S.A.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the l l l interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
l Consult the Support Service Center or an experienced radio/TV technician for help.
9
Safety Information
Safety Warnings
- For U.K.
WARNING
To assure continued compliance, use only shielded interface cables when connecting to a computer or peripheral. Also, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: l This device may not cause harmful interference received, including l interference that may cause undesired operation.
This device must accept any interference received, including interference that may cause undesired operation.
Failure to follow this precaution can result in death, serious injury, or equipment damage.
WARNING
This apparatus must be earthed for your safety.
To ensure safe operation the three-pin plug must be inserted only into a standard three-pin power point, which is effectively earthed through the normal household wiring.
Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth. Wrongly wired extension cords are a major cause of fatalities.
The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe.
For your safety, if you have any doubt about the effective earthing of the power point, consult a qualified electrician.
Failure to follow this precaution can result in death, serious injury, or equipment damage.
10
Safety Information
WARNING
THIS APPLIANCE MUST BE EARTHED
Important
The wires in this mains lead are coloured in accordance with the following code: l l l
Green-and-yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbols coloured GREEN or GREEN-and-YELLOW.
The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured RED.
The mains plug on this equipment must be used to disconnect the mains power.
Please ensure that a socket outlet is available near the equipment and is easily accessible.
Failure to follow this precaution can result in death, serious injury, or equipment damage.
11
Safety Information
WARNING l l
This equipment is not designed for connection to an IT power system:
An IT system is a system having no direct connections between live parts and Earth; the exposed conductive parts of the electrical installation are earthed.
An IT system is not permitted where the computer is directly connected to public supply systems in the UK.
Disconnect the mains plug from the supply socket when the computer is not in use.
Failure to follow this precaution can result in death, serious injury, or equipment damage.
Warnung Für
Deutschland
Warnung bezüglich der Lithiumbatterie (Sicherungsbatterie)
Lithiumbatterie
Dieser Computer enthält eine Lithiumbatterie zur Sicherung von Datum und Uhrzeit der eingebauten Uhr sowie anderer Systemdaten im Speicher bei einer
Unterbrechung der Hauptstromversorgung. Diese Sicherungsbatterie darf nur von
Kundendienstpersonal ausgewechselt werden.
Warnung! Bei falschem Gebrauch besteht Explosionsgefahr!
Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
12
Safety Information
Hazardous Location Installations - for USA and Canada
General Schneider Automation designed the systems with the intention of meeting the requirements of Class I, Division 2 hazardous location applications. Division 2 locations are those locations that are normally non-hazardous, but potentially hazardous should an accident expose the area to flammable vapors, gases or combustible dusts.
These systems are non-incendiary devices. They are not intrinsically safe and should never be operated within a Division 1 (normally hazardous) location when installed as described here. Nor should any peripheral interface device attached to these systems be located within Division 1 locations unless approved and/or certified diode barriers are placed in series with each individual signal and DC power line. Any such installations are beyond the bounds of Schneider Automation design intent. Schneider Automation accepts no responsibility for installations of this equipment or any devices attached to this equipment in Division 1 locations.
It is mandatory to install the Hazardous Location Kit Ref: MPCYN00HLK00N.
Warning
For AC version equipment only:
The power switch is an arcing device. It should be switched to the ON position and the corresponding retainer bracket for the Control Box should be attached according to the Hazardous Location Kit service instruction.
Only technically qualified service personnel should perform installation and service.
These workstations are designed to require no service in the course of normal operation by an operator.
Warning
It is the user's responsibility in case of maintenance or repair of any subassembly to verify that the exchanged or repaired module is labelled as a Class I Division 2 hazardous location.
It is the responsibility of the customer to ensure that the product is properly rated for the location. If the intended location does not presently have a Class, Division and
Group rating, then users should consult the appropriate authorities having jurisdiction in order to determine the correct rating for that hazardous location.
13
Safety Information
14
In accordance with Federal, State/Provincial, and Local regulations, all hazardous location installations should be inspected prior to use by the appropriate authority having jurisdiction. Only technically qualified personnel should install, service, and inspect these systems.
Warning
Suitable for use in Class I, Division 2 Groups A, B, C, and D, hazardous locations or non-hazardous locations only.
Warning - Explosion Hazard
Substitution of components may impair suitability for Class I, Division 2.
Warning
For a use in hazardous locations, the PCI or ISA controller cards shall be found in category NWHP2, provided that they are suitable for Class I,
Division 2, Groups A, B, C and D; T-Code: T4A, and suitable for an ambient temperature range of +0°C to +50°C.
Warning - Explosion Hazard
Do not connect or disconnect equipment unless the power has been switched off or the area is known to be non-hazardous.
Warning
Power wiring must be in accordance with the National Electrical Code article 501.4(B) for Class I, Division 2.
Warning - Explosion Hazard
When in hazardous locations, turn off power before replacing or wiring modules.
Definition
Safety Information
Warning - Explosion Hazard
Do not connect or disconnect the output ports such as PS2/USB/Serial/
Parallel/Video connectors, when the unit is in a Hazardous Location area
The following Class and Division explanations are derived from Article 500 (Sections
5 and 6) of the United States National Fire Protection Agency National Electric Code
(NFPA 70, 1990). They are not complete and are included here only for a general description for those not familiar with generic hazardous locations requirements.
Persons responsible for the installation of this equipment in hazardous locations are responsible for ensuring that all relevant codes and regulations related to location rating, enclosure, and wiring are met.
Class I Locations
Class I locations are those in which flammable gases or vapors are or may be present in the air in quantities sufficient to produce explosive or ignitable mixtures.
Class II Locations
Class II locations are those that are, or may become, hazardous because of the presence of combustible dust.
Division 1 Locations l l
A Division 1 location is one in which flammable or ignitable gases, vapors or combustible dusts and particles can exist due the following conditions:
Normal operating conditions.
Due to repair, maintenance conditions, leakage, or where mechanical failure or abnormal operation of machinery or equipment might release or cause explosive or ignitable mixtures to be released or produced.
l Combustible dusts of an electrically conductive nature may be present in hazardous quantities.
Note
Schneider Automation MPC••• systems are not suitable for installation within Class II Division 2 and Class 1 Division 1 locations.
15
Safety Information
Note
Electrical equipment cannot be installed in Division 1 locations unless they are intrinsically safe, installed inside approved explosion-proof enclosures, or installed inside approved purged and pressurized enclosures.
l l
Division 2 Locations l Class I volatile flammable liquids or flammable gases are handled, processed or used, but confined within closed containers or closed systems from which they can escape only in cases of accidental rupture or breakdown of such enclosures or systems, or in case of abnormal operation of equipment.
l Ignitable concentrations of Class I vapors or gases are normally prevented by positive mechanical ventilation, but may become hazardous due to mechanical failure of those ventilation systems.
Location is adjacent to a Division 1 location.
Class II combustible dust is not normally in the air in quantities sufficient to produce explosive or ignitable mixtures. Dust accumulations are normally insufficient to interfere with normal operation of electrical equipment or other apparatus. Combustible dust may be in suspension in the air as a result of the following: infrequent malfunctioning of handling or processing equipment; combustible dust accumulations on, or in the vicinity of, electrical equipment; may be ignitable by abnormal operation or failure of electrical equipment.
Groups
All electrical equipment that is approved for use in hazardous locations must include a group rating. Various flammable and combustible substances are divided into these groups as a function of their individual maximum experimental safe gap
(MESG), explosion pressure, and ignition temperature. Component temperatures and the potential for spark based upon voltage, current and circuit characteristics of electrical equipment will determine what the equipment group rating will be. A device approved for installation within Class I, Group A locations may also be used in
Groups B, C, or D.
Note
Approved Class I equipment may not be suitable for Class II installations.
Class I includes Groups A, B, C, and D. Class II includes Groups F, and G.
16
Power Switch
Cable connections
Safety Information
The amount of input power required by these systems classifies a power switch as an incendiary device because the voltage and current across the make/break device are capable of creating a spark.
Hazardous location regulations require that a power switch rated for ordinary locations may be used if it is located in an area specified as non-hazardous.
However, limits in cable length between the workstation and the power switch may apply. Otherwise the switch must be compliant with Class I, Division 1 requirements
(intrinsically safe). These switches are built in a manner that prevents the possibility of a spark when contacts are made or broken.
Use suitable UL listed and/or CSA Certified Class I, Division 1 switches in hazardous locations. These switches are available from a wide number of sources. It is the responsibility of the customer to ensure that the power switch selected for the installation has the correct hazardous locations rating for the location in which it is installed.
Division 2 hazardous location regulations require that all cable connections be provided with adequate strain relief and positive interlock. USB connections can never be used in hazardous location installations, because USB connectors do not provide adequate strain relief. Never connect or disconnect a cable while power is applied at either end of the cable. All communication cables should include a chassis ground shield. This shield should include both copper braid and aluminum foil. The
D-sub style connector housing should be a metal conductive type (e.g., molded zinc) and the ground shield braid should be well terminated directly to the connector housing. Do not use a shield drain wire.
The outer diameter of the cable must be suited to the inner diameter of the cable connector strain relief in order to ensure that a reliable degree of strain relief is maintained. Always secure the D-Sub connectors to the workstation-mating connectors via the two screws located on both sides.
Warning
Never connect or disconnect the communication cables while power is applied at either end of the cable. This may result in an incendiary spark.
Permanent damage to the workstation communication components may occur.
17
Safety Information
Operation and
Maintenance
The systems have been designed for compliance with relevant spark ignition tests.
However, please note that the workstation front panel keypad switches and PS/2 connector are the only make/break components intended to be exercised by the operator in the course of normal operation.
Warning - Explosion Hazard
The front PS/2 connector provides non incendive field circuit when connected in accordance with control drawing located in chapter 4.
Safety Agency
Approval
Always observe the following rules with respect to hazardous location installations: l l l
Always install the workstations within an enclosure suitable for the specific application. General-purpose enclosures may be acceptable for Class I applications but are never acceptable for Class II applications. Type 4 (IP 65) enclosures are recommended even when not required by regulations.
If present, keep enclosure doors or openings closed at all times, to avoid the accumulation of foreign matter inside the workstation.
Never subject the unit to any installation or service procedures unless power is removed and the area is known to be non-hazardous. This includes the installation or removal of power cables, communication cables, or removal of the rear cover of the unit.
The Schneider Automation systems are designed to meet the following standards: l l l l l
Underwriters Laboratories Inc., UL 1604 Standard for Safety Electrical equipment for use in Class I Division 2 locations
Underwriters Laboratories Inc., UL 60950, Information Technology Equipment
Canadian Standard Association, Specification C22.2 No. 213-M1987 Nonincendiary electrical equipment for use in Class I, Division 2 hazardous locations.
Canadian Standards Association, Specification C22.2 No. 950 Information
Technology Equipment
EN 60950, Information Technology Equipment
18
About the Book
At a Glance
Document Scope User manual for the Magelis iPC range of industrial PCs
Related
Documents
Title of Documentation
Magelis iPC installation guide
Reference Number
35005232
User Comments We welcome your comments about this document. You can reach us by e-mail at
19
About the Book
20
21
About the Book
22
General overview
I
At a Glance
Subject of this part
What's in this
Part?
This part provides an overview of the industrial PCs in the Magelis iPC range.
This part contains the following chapters:
Chapter
1
2
3
4
Chapter Name
Introduction
Physical overview
Characteristics
Specific functions
Page
23
General overview
24
Introduction
1
Introduction
Thank you
At a Glance
Congratulations!
Thank you for having purchased an industrial computer from the Magelis iPC range.
This computer, designed to operate in an industrial environment, features the very latest technologies.
Magelis iPC computers are modular products, made up of a Control Box and a Front
Panel that you have to assemble prior to commissioning (see Assembly of the front
panel onto the Control Box, p. 64).
The Control Box may however be used in stand-alone with a video monitor and an external keyboard (see
Mounting without a front panel, p. 108).
There are three versions of Control Box: l l
References: MPC AN•••
References: MPC BN••• l References: MPC CN••• with different characteristics (see
Control Box specifications, p. 40).
The Control-Boxes MPC BN••• and MPC CN••• also use a modular design in order to facilitate maintenance. They are made up of a power supply block, a control box block and a block for extension cards.
There are several versions of front panel: l l l
12" or 15" LCD screen
With or without built-in dust and damp proof keyboard
LCD screen may or may not be touch-sensitive
25
Introduction
26
Physical overview
2
At a Glance
Subject of this chapter
What's in this
Chapter?
This chapter provides physical overviews of the products.
This chapter contains the following sections:
Section
2.1
2.2
Topic
Description of the Control Boxes
Description of the front panels
Page
27
Physical overview
2.1
Description of the Control Boxes
At a Glance
Subject of this
Section
What's in this
Section?
This section describes the different models of Control Box.
This section contains the following topics:
Topic
MPC AN••• Control Box
MPC BN••• Control Box
MPC CN••• Control Box
Page
28
Physical overview
MPC AN••• Control Box
Description View of an MPC AN•••:
1 15 14
2
3
11
12
13
14
7
8
9
10
4
5
6
2
3
Number Designation
1 On-Off switch and power supply connection (mains or 24 V DC)
Cooling blowers
Front panel connector
Diskette drive
RJ45 Ethernet link connector
15-pin, female, VGA output SUB-D connector for connection to an external video monitor
25-pin, female, LPT parallel port SUB-D connector for printer
2 x 9-pin, male RS 232 serial port SUB-D connectors
9-pin, female RS422/RS485 SUB-D connector
External keyboard input (see note)
External mouse port (see note)
2 USB port connectors
Slot for CD-ROM drive (optional)
Ventilation grill and dust filter
13
12
11
10
9
6
5
4
8
7
29
Physical overview
Number Designation
15 On the rear panel: l l
Hatch for access to RAM memory strips
Blower with dust filter
Note: The external keyboard input (No. 10) and external mouse input (No. 11) are only authorized when the Control Box is used in stand-alone with an external video monitor.
30
Physical overview
MPC BN••• Control Box
Description View of an MPC BN•••:
17
1
2
3 4
16
5
15
6
14
8
7
13
12
11
10
9
18
7
8
4
5
6
2
3
Number
1
Designation
Cooling blowers
Front panel connector
Hard disk
Removable CD-ROM and disk drive drawer
RJ45 Ethernet link connector
15-pin, female, VGA output SUB-D connector for connection to an external video monitor
25-pin, female, LPT parallel port SUB-D connector for printer
ISA/PCI extension card slots
31
Physical overview
15
16
17
18
11
12
13
14
Number
9
10
Designation
2 x 9-pin, male RS 232 serial port SUB-D connectors
9-pin, female RS422/RS485 SUB-D connector
External keyboard input (see note)
External mouse port (see note)
Mains or 24 V DC terminal block socket
On-Off switch
2 USB port connectors
Ventilation grill with dust filter
Power supply block
Block with slots for extension cards
Note: The external keyboard input (No. 11) and external mouse input (No. 12) are only authorized when the Control Box is used in stand-alone with an external video monitor.
32
Physical overview
MPC CN••• Control Box
Description View of an MPC CN••• mains supply:
18 17
1
16
15
2
3 4 5 6
7
8
9
4
5
6
2
3
Number
1
Designation
Cooling blowers
Front panel connector
Hard disk
Removable CD-ROM and disk drive drawer
RJ45 Ethernet link connector
15-pin, female, VGA output SUB-D connector for connection to an external video monitor
25-pin, female, LPT parallel port SUB-D connector for printer
6 ISA/PCI extension card slots
2 x 9-pin, male RS 232 serial port SUB-D connectors
33
14
8
7
13
12
11
10
9
19
Physical overview
16
17
18
19
12
13
14
15
Number
10
11
Designation
9-pin, female RS422/RS485 SUB-D connector
External keyboard input (see note)
External mouse port (see note)
Mains or 24 V DC terminal block socket
On-Off switch
Power supply blower
2 USB port connectors
Ventilation grill with dust filter
Power supply block
Block with slots for extension cards
Note: The external keyboard input (No. 11) and external mouse input (No. 12) are only authorized when the Control Box is used in stand-alone with an external video monitor.
34
2.2
Description of the front panels
At a Glance
Subject of this section
What's in this
Section?
This section describes the different front panels of the products.
This section contains the following topics:
Topic
MPC NT•• front panels
MPC NA•• and MPC NB•• front panels
Physical overview
Page
35
Physical overview
MPC NT•• front panels
At a Glance
Description
These front panels come with a 12" or 15" touch-sensitive screen.
View of an MPC NT•• front panel
LEDs
Touch-sensitive screen
Brightness control
External keyboard/ mouse socket*
Infra-red link
36
Physical overview
MPC NA•• and MPC NB•• front panels
At a Glance
Description
These front panels come with a 12" or 15" screen and a keyboard. For the MPC
NB••, the screen is touch-sensitive.
View of an MPC NA•• or MPC NB•• front panel
LEDs
Screen (touch-sensitive for MPC NB••)
User function**/Alpha keys
Number keypad and arrow keys
External keyboard/ mouse socket
Infra-red link
Function/
Alpha keys
Function/Alpha switch key
*See
**The user function keys can be used by an application.
Touch-sensitive cursor
37
Physical overview
38
Characteristics
At a Glance
Subject of this chapter
What's in this
Chapter?
This chapter gives the product characteristics.
This chapter contains the following sections:
Section
3.1
3.2
3.3
Topic
Control Box specifications
Characteristics of the front panels
Environment characteristics
3
Page
39
Characteristics
3.1
Control Box specifications
At a Glance
Subject of this
Section
What's in this
Section?
This section specifies the characteristics of the Control Boxes.
This section contains the following topics:
Topic
Characteristics of the MPC AN••• products
Characteristics of MPC BN••• products
Characteristics of MPC CN••• products
Page
40
Characteristics
Characteristics of the MPC AN••• products
Introduction
Shared characteristics
The characteristics of the MPC AN••• products differ from model to model. These are given below according to product reference.
Characteristics:
Processor
Ram
Hard disk
Video card
Disk drive
CD-ROM drive
Ethernet TCP/IP link
USB port
COM4 serial port
COM1 serial port
Parallel port
Extension card slot
Dimensions
Weight
Intel Celeron with a clock frequency greater than or equal to 566 MHz
SDRAM 128 Mb, upgradeable to 512 Mb
Capacity greater than or equal to 20 Gb IDE - 2" 1/2
64 bit PCI controller, 2 Mb of Ram
3.5", 1, 44 Mb - fixed
Optional
1 x 10/100base TX (RJ45) interface
2 x 12Mb/s links
1 x RS232 or RS 422/485 (exclusive) serial link
1 x RS 232 link
1 bi-directional link
-
See
16 lbs
Power supply Power supply of MPC AN•• •A• products (AC):
Supply voltage
Frequency
115...230 V AC - 50/60 Hz, (threshold values: 90...264 V AC)
50/60 Hz (threshold values: 47/63 Hz), EN 61131-2 compliant
Consumption 80
Micro-cuts 10 ms
Power supply of MPC AN•• •D• products (DC):
Supply voltage 24 V DC, (threshold values: 18...36 V)
Consumption 80
Micro-cuts 1 ms
41
Characteristics
Operating systems
Pre-installed packs
The products are delivered with a pre-installed operating system according to the reference ordered.
l l l
The products have been tested with the following operating systems:
Microsoft Windows 2000
Microsoft Windows NT4 SP6
Microsoft Windows 98
Pre-installed packs according to product reference:
Reference
MPC AN•• ••• ••N
MPC AN•• ••• ••A
Software
No pre-installed pack
Vijeo Look Run Time 1024
Hardware
-
-
42
Characteristics
Characteristics of MPC BN••• products
Introduction
Shared characteristics
The characteristics of the MPC BN••• products differ from model to model. These are given below according to product reference.
Characteristics:
Ram
Hard disk
Video card
Disk drive
CD-ROM drive
Ethernet TCP/IP link
USB port
COM4 serial port
COM1 serial port
Extension card slot
Dimensions
Weight
SDRAM 128 Mb, upgradeable to 512 Mb
Capacity greater than or equal to 20 Gb IDE - 2" 1/2
64 bit PCI controller, 2 Mb of Ram
3,5", 1,44 Mo - extractible
24x, removable
1 x 10/100base TX (RJ45) interface
2 x 12Mb/s links
1 x RS232 or RS 422/485 (exclusive) serial link
1 x RS 232 link
1 ISA card slot
1 PCI card slot (slave mode only)
1 mixed (ISA/PCI) slot
See
23 lbs
Processor Type of processor according to product reference:
Reference Operating system
MPC BN•2 ••• Intel Celeron with a clock frequency greater than or equal to 566 MHz
MPC BN•5 ••• Intel Pentium III with a clock frequency greater than or equal to 850 MHz
43
Characteristics
Power supply
Operating systems
Pre-installed packs
Power supply of MPC BN•• •A• products (AC):
Supply voltage
Frequency
115...230 V AC - 50/60 Hz, (threshold values: 90...264 V AC)
50/60 Hz (threshold values: 47/63 Hz), EN 61131-2 compliant
Consumption 130
Micro-cuts 10 ms
Power supply of MPC BN•• •D• products (DC):
Supply voltage 24 V DC, (threshold values: 18...36 V)
Consumption 130
Micro-cuts 1 ms
The products are delivered with a pre-installed operating system according to the l l l reference ordered.
The products have been tested with the following operating systems:
Microsoft Windows 2000
Microsoft Windows NT4 SP6
Microsoft Windows 98
Pre-installed packs according to product reference:
Reference
MPC BN•• ••• ••N
MPC BN•• ••• ••A
MPC BN•• ••• ••B
MPC BN•• ••• ••C
MPC BN•• ••• ••D
Software
No pre-installed pack
Vijeo Look Run Time 1024 I/O
Vijeo Look Run Time 1024 I/O
Vijeo Look Run Time 1024 I/O
PL7 Pro
Vijeo Look Run Time 1024 I/O
PL7 Pro
-
-
Hardware
-
-
T PCX 57203
44
Characteristics
Characteristics of MPC CN••• products
Introduction
Shared characteristics
The characteristics of the MPC CN••• products differ from model to model. These are given below according to product reference.
Characteristics:
Ram
Hard disk
Video card
Disk drive
CD-ROM drive
Ethernet TCP/IP link
USB port
COM4 serial port
COM1 serial port
Extension card slot
Dimensions
Weight
SDRAM 128 Mb, upgradeable to 512 Mb
Capacity greater than or equal to 20 Gb IDE - 2" 1/2
64 bit PCI controller, 2 Mb of Ram
3.5", 1,44 Mo - removable
24x, removable
1 x 10/100base TX (RJ45) interface
2 x 12Mb/s links
1 x RS232 or RS 422/485 (exclusive) serial link
1 x RS 232 link
2 ISA card slots
3 ISA card slots
1 mixed (ISA/PCI) slot
See
29 lbs
Processor Type of processor according to product reference:
Reference
MPC CN•2 ••• •••
MPC CN•5 ••• •••
Operating system
Celeron with a clock frequency greater than or equal to 566 MHz
Pentium III with a clock frequency greater than or equal to 850 MHz
45
Characteristics
Power supply
Operating systems
Pre-installed packs
Power supply of MPC CN•• •A• products (AC):
Supply voltage
Frequency
115...230 V AC - 50/60 Hz, (threshold values: 90...264 V AC)
50/60 Hz (threshold values: 47/63 Hz), EN 61131-2 compliant
Consumption 170
Micro-cuts 10 ms
Power supply of MPC CN•• •D• products (DC):
Supply voltage 24 V DC, (threshold values: 19...32 V)
Consumption 170
Micro-cuts 1 ms
The products are delivered with a pre-installed operating system according to the l l l reference ordered.
The products have been tested with the following operating systems:
Microsoft Windows 2000
Microsoft Windows NT4 SP6
Microsoft Windows 98
Pre-installed packs according to product reference:
Reference
MPC CN•• ••• ••N
MPC CN•• ••• ••E
Software
No pre-installed pack
Vijeo Look Run Time 1024 I/O
PL7 Pro
Hardware
-
T PCX 57353
46
Characteristics
3.2
Characteristics of the front panels
Characteristics of the front panels
Introduction The characteristics of the front panels differ from model to model. These are given below.
Characteristics Shared characteristics:
Number of colors
Brightness
Infra-red link
Power supply
262144
200 Cd/m
2
(typical value), adjustable
IrDA Standard
By Control Box unit
Specific characteristics:
Reference Screen type
Scree n size
Definition View angle
800x600 Hor. 110°
Vert. 90°
Touchsensitive
Screen
Analog resistant
35 million cycles
Keyboard
MPC NT2• SVGA active matrix
MPC NT5• XGA active matrix
MPC NA2• SVGA active matrix
MPC NA5• XGA active matrix
MPC NB2• SVGA active matrix
MPC NB5• XGA active matrix
12"
15"
12"
15"
12"
15"
1024x768 Hor. 160°
Vert. 160°
Analog resistant
35 million cycles
-
800x600
800x600
Hor. 110°
Vert. 90°
Hor. 110°
Vert. 90°
-
1024x768 Hor. 160°
Vert. 160°
-
1024x768 Hor. 160°
Vert. 160°
Analog resistant
35 million cycles
Analog resistant
35 million cycles
IBM standard 70-key alphanumeric
2x10 user function keys
IBM standard 70-key alphanumeric
2x10 user function keys
IBM standard 70-key alphanumeric
2x10 user function keys
IBM standard 70-key alphanumeric
2x10 user function keys
For the front-panel dimensions, please refer to
Weig ht
(Kg)
6.5
7.1
6.6
7.2
6.6
7.2
47
Characteristics
3.3
Environment characteristics
Environment characteristics
General The environment characteristics given below are applicable to both the Control
Boxes and the front panels of the products.
Characteristics
Specification
Degree of Protection
Storage temperature
Usage altitude
Storage altitude
Vibration
(in operation)
Shock Resistance
(in operation)
Hygrometry
Interference immunity
The environment characteristics are as follows:
Operating temperature
Value l l
IP65 for the forward part of the front panels.
IP 20 for the rest of the product
0°C to 50°C
-25°C to 60°C
0 to 3000m max.
0 to 12000m max.
75-micron amplitude from 10 to 57 Hz,
1g amplitude from 57 to 150 Hz
15g over 11ms
20...80%
High frequency interference
Electromagnetic Emissions
Human and material safety
Standards
-
In accordance with EN 61131-2, UL 508 for standard location, UL 1604 for Class I,
Division 2 hazardous location.
IEC 68-2-2 Bb and Ab tests,
IEC 68-2-14 Na test and EN 61131-2 compliant
-
-
IEC 68-2-6 Fc test and EN 61131-2 compliant
IEC 68-2-27 Ea test and EN 61131-2 compliant
-
EN 61131, IEC 1000-4-3/6 level 3
Class A/EN 55022/55011
EN 61131-2, UL/CSA and IEC 529/EN 60950
Certification The products have been developed to comply with the following standards: l l l l l l
UL 508
IEC/EN 60950
CUL
EN 55022
IEC/EN 61131-2
Classification in hazardous areas: class 1 - division 2 - UL 1604
48
Specific functions
4
At a Glance
Subject of this chapter
What's in this
Chapter?
This chapter describes the specific functions of MPC products.
This chapter contains the following topics:
Topic
Specific keys
Touch-sensitive cursor
LED indicators
Control drawing of the PS/2 outlet on the Magelis iPC front panels
Installation of Kit MPCYN00HLK00N for Class I, Division 2 Hazardous
Locations.
Page
49
Specific functions
Specific keys
At a Glance
Dual-function keys
On front panels with a keyboard, there are keys with a specific function. These are described below.
View of dual-function keys:
The keys boxed in on the above illustration are dual-function keys.
Depending on the status of the ABC key, these keys either work as the function keys
F1 to F12 and the user function keys PF1 to PF20 , or as the alpha keys
QWERTYUIOP etc.
. The LED for the ABC key is lit when it is in the Alpha position.
50
Brightness control
Specific functions
The brightness of the LCD screen is adjusted in different ways depending on the type of front panel. The two types of adjustment are shown below.
View of brightness adjustment keys on MPC NT••• front panels
Increases brightness
Decreases brightness
View of brightness adjustment keys on MPC NA••• and MPC NB••• front panels
These keys are located on the number pad (to the right of the front panel).
To make an adjustment: l Hold down the key, then press the key to increase the brightness l Hold down the key, then press the key to decrease the brightness
51
Specific functions
PF keys Pressing a PFx key corresponds to pressing a sequence of keys. The key sequences are given below.
PF8
PF9
PF10
PF11
PF12
PF13
PF14
PF15
PF4
PF5
PF6
PF7
PF key
PF1
PF2
PF3
PF16
PF17
PF18
PF19
PF20
Sequence
CTRLL ALTL F1
CTRLL ALTL F2
CTRLL ALTL F3
CTRLL ALTL F4
CTRLL ALTL F5
CTRLL ALTL F6
CTRLL ALTL F7
CTRLL ALTL F8
CTRLL ALTL F9
CTRLL ALTL F10
CTRLL ALTL F11
CTRLL ALTL F12
CTRLL ALTL I
CTRLL ALTL M
CTRLL ALTL H
CTRLL ALTL A
CTRLL ALTL B
CTRLL ALTL C
CTRLL ALTL D
CTRLL ALTL F
Note: CTRLL = left "Ctrl" key, ALTL = left "Alt" key
52
Specific functions
Touch-sensitive cursor
At a Glance
Description
Front panels with a keyboard feature a touch-sensitive cursor in the bottom righthand corner. It is described below.
View of the touch-sensitive cursor:
Cursor movement button
Left button Right button
53
Specific functions
LED indicators
At a Glance
Meaning
On the front panel there are three LED indicators, the meanings of which are as follows.
ON
DISK
LAN
This is lit when the computer is powered-up
This shows when read/write operations are being performed on the hard disk
This shows when data is being exchanged on the built-in Ethernet link
54
Specific functions
Control drawing of the PS/2 outlet on the Magelis iPC front panels
Introduction
Description
The information below concerns the use of the PS/2 outlet located on the front panels of the Magelis iPC used in Class I, Division 2 Groups A, B, C and D hazardous locations.
Information taken from the Schneider Electric document: 35007197P07000.
MPCN•••••••••Model Mouse/Keyboard
The equipment used with non-incendive cabling
Description of PS/2 pinouts:
1. Data
2. Not Connected
3. GND
4. VCC (see Note 1 for details)
5. CLK
6. Not Connected
4
6
2 1
5
3
Notes:
Note
1
2
Description
Non-incendive circuit parameters: l PS/2 port: l Voc = 5.1 V l l l
Isc = 5.5 A
Ca = 175 µ F
La = 1.5
µ
H
The equipment used with non-incendive cabling must comply with the following demands:
Apparatus used with nonincendive cabling (mouse, keyboard)
Industrial PC
MPCN••••••••• model
Voc
Isc
Ca
La
≤
≤
≤
≤
Vmax:
Imax:
Ci + C cable
Li + L cable
55
Specific functions
4
5
Note
3
Description
If the electrical parameters of the cable are not known, the following values should be used: l l
Capacitance 60 Pf/ft
Inductive - 0.20
µ
H/ft
The non-incendive cabling must be installed in compliance with Article 501.4(B)(3) of the National Electrical Code ANSI/NFPA 70.
The apparatus used with non-incendive cabling must not contain or be connected to another power source.
56
Specific functions
Installation of Kit MPCYN00HLK00N for Class I, Division 2 Hazardous Locations.
Warning The MPCYN00HLK00N kit is intended for use in Class I, Division 2 Groups A, B, C, and D
It applies exclusively on AC 100/240V 50/60Hz Magelis iPC Control Boxes reference MPC AN ** * A *, MPC BN ** * A *, MPC CN ** * A *.
WARNING
Location of the Magelis iPC
In Class I, Division 2 hazardous locations, The Magelis iPC must be wired according to the National Electric Code and/or Canadian Electric code as it applies to hazardous locations. Refer to the General Safety
Information of the Magelis iPC external screen monitor User Manual.
Failure to follow this precaution can result in death, serious injury, or equipment damage.
Package contents l l
The shipping carton shall contains the following items: l l l l power cable retainer bracket for Small Control Box, power cable retainer bracket for Medium Control Box, power cable retainer bracket for Large Control Box, spare parts screw bag with: l l
2 x #6-32 screws for Large Control Box, and 7 x M3 Pozidriv L=6mm screws for Small/Medium Control Box, power cable, this service instruction.
57
Specific functions
Installing your
Magelis iPC in a
Class I, Division
2 Hazardous
Location.
l l l l
Prepare the plug-less end of the AC power cable by following the steps: l If needed, cut the power cable to the desired length.
l l
Strip 2.5 inches (60mm) of the cable sheath,
Strip 1/4 inch (6mm) of insulation from the end of 3 conductor wires, l Crimp a terminal to the stripped wire ends to keep the copper strands from fraying.
Connect the molded end of the cable to the mating connector on the side of the
Magelis iPC.
Operate the mains switch of the Magelis iPC in ON position.
Secure the power cable by mounting the cable retainer bracket that corresponds to the Control Box. See figures below.
WARNING
Explosion Hazard
You shall install the power cord retainer bracket to ensure safety in hazardous locations. The role of the bracket is to secure the power cable from accidental disconnection and avoid the operation of the AC power switch which is an arcing device.
Failure to follow this precaution can result in death, serious injury, or equipment damage.
l l l l
To connect the Magelis iPC to the power supply:
Turn off the main switch or breaker,
First connect the ground wire (green wire) to the terminal block of the cabinet with the right tightening torque,
Then connect the two other wires (Live: black wire and Neutral: white wire),
Restore the AC power for start.
58
Cable Retainer
Bracket
Mounting
Specific functions
The chart below describes installation of the feeding cable retainer bracket:
Illustration l l
Description l l
Remove the 3 screws pointed by the arrows,
Connect the power cable,
Operate power switch to ON position,
Place the retainer bracket and fasten with the screws l l l l
Remove the 4 screws pointed by the arrows,
Connect the power cable,
Operate power switch to ON position,
Place the retainer bracket and fasten with the screws
59
Specific functions
Illustration l l
Description l l
Remove the 2 screws pointed by the arrows,
Connect the power cable,
Operate power switch to ON position,
Place the retainer bracket and fasten with the screws
60
Implementation
II
At a Glance
Subject of this part
What's in this
Part?
This part concerns the implementation of products.
This part contains the following chapters:
Chapter
5
6
7
8
9
Chapter Name
Assembly and connections
Getting started
Hardware extensions
Configuration of the Bios
Maintenance
Page
61
Implementation
62
Assembly and connections
5
At a Glance
Subject of this chapter
What's in this
Chapter?
This chapter concerns the assembly and connection of the products.
This chapter contains the following topics:
Topic
Assembly of the front panel onto the Control Box
Mains supply of the Control Boxes
Direct current supply of Control Boxes
Page
63
Assembly and connection
Assembly of the front panel onto the Control Box
At a Glance
Procedure
If you are using one of the computers in the range with a MPC NT••, MPC NA•• or
MPC NB•• type front panel, you must first assemble this front panel onto the Control-
Box. These operations must be performed with the power switched off .
In order to assemble the two sections, use a Pozidriv cross-slot screwdriver and follow the instructions below:
1 Assemble the Control-Box on the front panel using the 4 alignment studs located at the rear of the front panel
Control-Box
4 alignment studs
Front panel
2 Fasten the assembly at all points around the Control Box, using the 12 crossslot screws supplied
12 cross-slot screws
Control-Box
Front panel
64
Assembly and connection
Mains supply of the Control Boxes
At a Glance Alternating Current versions of the Control Boxes are connected to the mains using the lead supplied.
CAUTION
It is essential to connect the computer to the ground via the power supply's terminal block
Failure to follow this precaution can result in injury or equipment damage.
Note: Protection fuse : The mains supply modules for the Control Boxes are fitted with a protection fuse as standard. This fuse is located inside the module but cannot be accessed.
Note: The MPC AN•• and supply module of the MPC BN•• are equipped with a 3.15
A time-delayed fuse located in the mains input connector. In the event of error, it is essential that this fuse be replaced by a fuse of the same rating.
65
Assembly and connection
Direct current supply of Control Boxes
At a Glance Direct current versions of the Control Boxes connect to a 24 V DC supply (see
Control Box specifications, p. 40).
Note: It is not advisable to use direct current Control Box supplies featuring a strong inrush current on a direct current network with a fold back current limitation protection.
When a supply module is connected to a direct current network, it is compulsory to limit the length of the supply cable, in order to prevent line losses: l Supply of an MPC AN••• or MPC BN•••: l Length limited to 30 meters (60 meters 'round-trip') with 2.5 mm
2
section copper wires l l Length limited to 20 meters (40 meters 'round-trip') with 1.5 mm copper wires
Supply of an MPC CN•••:
2
section l l
Length limited to 15 meters (30 meters 'round-trip') with 2.5 mm
2
section copper wires
Length limited to 10 meters (20 meters 'round-trip') with 1.5 mm
2
section copper wires
66
Possible connections
Assembly and connection
Connection of a Magelis iPC supplied by a non-grounded safety DC network:
The 0V and mechanical ground are connected internally inside the front panels and
Control-Boxes, as well as in the network cabling accessories.
Specific connection measures are to be taken for specific applications that use a floating mounting. These depend on the chosen mode of installation.
For this, the 24 V DC input of the Control Box supplies is isolated in relation to the outputs and mechanical ground: l Primary/Secondary dielectric strength: l l MPC AN•/BN• : 500 V AC l MPC CN• : 3000 V AC
Primary/Ground dielectric strength: l MPC AN•/BN• : 500 V AC l MPC CN• : 1500 V AC
Connection of a 24 V DC Magelis iPC using a floating direct current network:
Circuit diagram
Low voltage
AC network
Magelis iPC
Battery charger
Battery
Isolation controller
+
-
Floating 24 V DC network
+24 V
-0 V
67
Assembly and connection
Connection of a 24 V DC Magelis iPC using a ground referenced network:
100-240 V AC network
L
N
Q
PE
KM
(2)
~
+24/48
- +
V DC
Magelis iPC
+
-
(1)
(1)
Sensor/actuator/PLC supply
KM: Line contactor or circuit breaker
(1) : Isolation strip for detecting grounding faults
(2) : possibility of using a TSX SUP••• process supply
(see Schneider Automation product catalog).
Note: Protection fuse : the 24 V DC mains supply modules for the Control Boxes are fitted with a protection fuse as standard. This fuse, fitted in series with the 24
V DC input, is located inside the module but cannot be accessed.
Terminal block View of the connection terminal block:
24 VIN
V+ V- FG
68
FG is the ground connection. It is connected to the mechanical ground of the Control
Box.
Tightening torque of the terminal block screws: 1 N.m
.
Getting started
6
First power-up
Warning
Note: Before the first power-up, please read the "LIMITED USE LICENSE
AGREEMENT" carefully, then remove the seal.
Preparation On first power-up, it is necessary, depending on the software configuration of your
MPC••, to perform the following operations: l l
Customization and parametering of the operating system
Installation, customization and parametering of Schneider Automation and
Schneider Electric applications (PL7 Junior or PL7 Pro, Vijeo Look, OFS, MMI 17,
XBT-L1000, PL7-07)
For these different operations, refer to the "MPC installation guide" (ref. 35005232).
69
Getting started
70
Hardware extensions
7
At a Glance
Subject of this chapter
What's in this
Chapter?
This chapter concerns the hardware extensions for the Magelis iPC range of industrial PCs.
This chapter contains the following topics:
Topic
Removing/inserting the CD-ROM and diskette drive
Disassembling the modules
Installing an extension card
Adding a memory extension card
Page
71
Hardware extensions
Removing/inserting the CD-ROM and diskette drive
At a Glance A removable CD-ROM and diskette drive is installed in the MPC BN••• and MPC
CN••• Control Boxes. The procedure for removing and inserting this drive is given below.
Note: MPC AN••• Control Boxes are installed with a CD-ROM drive only, but the procedure is similar.
CAUTION
Static electricity may destroy electronic components. Always handle the drive by its metal cover.
Removing the drive the removal procedure for the drive is as follows:
1
2
3
Switch off the power to the computer
Unscrew the two fastening screws of the drive
Remove the drive from its housing by gently pulling it towards you using the fastening screws
Inserting the drive the insertion procedure for the drive is as follows:
1
2
3
Switch off the power to the computer
Position the drive in its housing and gently push it in until the stop is reached.
Tighten the fastening screws alternately
72
Hardware extensions
Disassembling the modules
At a Glance
Power supply module
In order to maintain the MPC BN•• and MPC CN•• products, it is possible to replace the power supply module and extension card module. The procedure is as follows.
Disassembly/Reassembly:
1
2
Disconnect the supply lead
Unscrew the four fastening screws at the rear of the MPC using a cross-slot screwdriver
3 Remove the power supply module
4 To reassemble the module, perform the above operations in the reverse order using the alignment studs
Note : For MPC CN•• products, it is necessary to link the power supply block to the extension card block with a connector
73
Hardware extensions
Extension module
Disassembly/Reassembly:
1
2
3
Disconnect the supply lead
Caution!
: For MPC CN•• products, first remove the power supply module
Unscrew the four fastening screws at the rear of the MPC extension block using a cross-slot screwdriver
4 Remove the extension module
5 To reassemble the module, first replace the extension card block, then the power supply block
74
Hardware extensions
Installing an extension card
At a Glance
Installation
MPC BN•• and MPC CN•• Control Boxes feature a compartment for ISA and/or PCIformat extension cards.
The procedure for installing a card is given below.
In order to install an extension card, use a Pozidriv cross-slot screwdriver and follow the steps described below:
1
2
Switch off the power to the computer
Unscrew the four knurled screws located under the Control Box in order to remove the cover of the hatch giving access to the extension card slots
3
4
4 knurled screws
Select an ISA or PCI slot
Unscrew the cable plate screw and remove
Screw and cable plate
75
Hardware extensions
5 Unscrew the two fastening screws from the extension card retaining bracket that correspond to the selected slot, release from the oblongs and remove.
Holding parts
Oblongs
6
7
Fastening screw
Place the card in its connector until the stop is reached
Attach the front panel of the card to the Control Box using the screw
76
8
Screw
Replace the holding part of the card so that it comes into contact with the top of the extension card, thus preventing the card from coming away from its connector.
Position the moving part to suit the length of the card, and to facilitate access to its functions, where necessary. Then tighten the screw on the moving part, then the fastening screws.
Moving part
Oblongs
9
Enlarged view of the holding part
Screw Fastening screw
Replace the hatch cover and tighten the 4 knurled screws
Hardware extensions
Adding a memory extension card
At a Glance It is possible to increase the memory capacity of the Control Boxes. A memory card access hatch is provided for this purpose. The procedure for accessing the memory extension cards is provided below.
CAUTION
Static electricity may destroy electronic components. Always handle cards by their edges, without touching the components or the conducting tracks.
MPC AN••• The procedure for accessing memory extension cards is as follows:
5
6
1
2
3
4
Switch off the power to the computer
Unscrew the four cross-slot screws of the cover located at the rear of the computer.
Insert a memory extension card in a free slot, ensuring proper direction of insertion.
Secure the card in its slot by folding inwards the plastic fastening tabs located at each end.
Replace the rear cover by tightening the four cross-slot screws.
Power-up the computer and, when requested, press F1 to acknowledge the new configuration
MPC BN•• and
MPC CN••
The procedure for accessing memory extension cards is as follows:
1 Switch off the power to the computer
2 Remove the supply block by unscrewing the four cross-slot screws and pulling it towards you (see
Disassembling the modules, p. 73
).
You now have access to the memory card hatch
3 Unscrew the cross-slot screws in order to remove the cover of the memory slot hatch.
4 Insert a memory extension card in a free slot, ensuring proper direction of insertion.
5 Secure the card in its slot by folding inwards the plastic fastening tabs located at each end.
6 Replace the rear cover by tightening the three cross-slot screws.
7 Replace and tighten the screws of the power supply block
8 Power-up the computer and, when requested, press F1 to acknowledge the new configuration
77
Hardware extensions
78
Configuration of the Bios
8
At a Glance
What's in this
Chapter?
What's in this
Chapter?
This chapter describes how to access certain parameters of the Bios (operating system of the computer) that need to be modified depending on its existing configuration.
This chapter contains the following topics:
Topic
Accessing the Bios configuration
Configuration screens
Modifying the date and time
Modifying the User password
Page
79
Configuration of the Bios
Accessing the Bios configuration
Procedure In order to access the configuration screen, follow the instructions below:
1
2
3
Power-up or restart the computer by pressing Ctrl+Alt+Del simultaneously
When the message "Press Del to enter Setup" appears, press Del
The configuration screen is displayed
Illustration Bios configuration welcome screen:
ROM PCI/ISA BIOS (2A69KACA)
CMOS SETUP UTILITY
AVARD SOFTWARE, INC.
STANDARD CMOS
BIOS FEATURES SETUP
CHIPSET FEATURE SETUP
POWER MANAGEMENT SETUP
PnP/PCI CONFIGURATION
LOAD BIOS DEFAULTS
LOAD SETUP DEFAULTS
Esc: Quit
F10: SAVE & EXIT SETUP
INTEGRATED PERIPHERALS
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
SAVE & EXIT SETUP
EXIT WITHOUT SAVING
: Select Item
(Shift)F2: Change Color
Time, Date, Hard Disk Type
80
Configuration of the Bios
Configuration screens
General 13 headings are available from the welcome screen.
l Use the 4 arrow keys to move from one heading to another
Headings l l l
The ESC key is used to quit configuration mode
The F10 function key is used to save modifications and quit configuration mode
The keys Shift+F2 are used to modify the color of the screens
Description of the different headings:
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURE SETUP
POWER MANAGEMENT SETUP
PnP/PCI CONFIGURATION
LOAD BIOS DEFAULTS
LOAD SETUP DEFAULTS
INTEGRATED PERIPHERALS
SUPERVISOR PASSWORD
This is used to modify the standard parameters in the
CMOS memory, such as the date, time and display.
This is used to modify the characteristics of the Bios.
We strongly recommend that you do not modify these values.
This is used to modify the characteristics of the
Chipset.
We strongly recommend that you do not modify these values.
This is used to modify the power saving mode for the power supply, hard drive and video.
We strongly recommend that you do not modify these values.
This is used to configure the PCI bus.
We strongly recommend that you do not modify these values.
This is used to restore the Bios parameters to factory values (for example to restart with stable values in the event of problems).
This is used to restore the parameters of the Bios with optimized values.
This is used to modify the parameters of internal peripherals.
We strongly recommend that you do not modify these values.
This is used to enter a password in order to access the
Bios configuration.
81
Configuration of the Bios
USER PASSWORD
IDE HDD AUTODETECTION
SAVE & EXIT SETUP
EXIT WITHOUT SAVING
This is used to define a user password for the machine.
This is used to automatically detect the hard drive installed in the machine or to modify the type of hard drive.
We strongly recommend that you do not use this function.
This is used to save modifications in the CMOS memory and to quit the Bios configuration.
This is used to quit configuration without saving the modifications made.
Note: The rest of this chapter will only contain descriptions of the screens that may need to be modified during the course of use. All other screens shall only be modified at the request of a properly informed technical department.
82
Configuration of the Bios
Modifying the date and time
At a Glance The date and time stored in the computer can be adjusted from the Standard CMOS
Setup screen of the Bios configuration utility.
View of the screen:
ROM PCI/ISA BIOS (2A69KACA)
STANDARD CMOS SETUP
AWARD SOFTWARE, INC.
Date (mm : dd : yy) : Thu, Sep 20 2001
Time (hh : mm : ss) : 12 : 45 : 53
HARD DISKS TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE
Primary Master : Auto 0M 0 0 0 0 0 AUTO
Primary Slave : Auto 0M 0 0 0 0 0 AUTO
Secondary Master : Auto 0M 0 0 0 0 0 AUTO
Secondary Slave : Auto 0M 0 0 0 0 0 AUTO
Drive A : 1.44, 3.5 in.
Drive B : None
LCD&CRT : Both
Panel : 1024x768 TFT
Halt On : All Errors
Base Memory : 640K
Extended Memory : 64512K
Other Memory : 384K
Total Memory : 65536K
ESC : Quit
F1 : Help
: Select Item
(Shift)F2 : Change Color
PU/PD/+/- = Modify
Procedure The procedure for modifying the time and date of the PC is as follows:
1 Use the arrow keys to select the date or time of the PC
2
3
4
Modify the value using the PageUp and PageDown keys
Use the ESC key to quit the modification mode and return to the welcome screen
Save the modifications by pressing F10 .
83
Configuration of the Bios
Modifying the User password
At a Glance The user password can be modified from the Bios configuration welcome screen.
Note: The password can be assigned either when the computer is started
(System), or when the Bios is modified (Setup). This option can be chosen by selecting Security Option in the BIOS FEATURE SETUP screen.
In order for the password to be active on start-up, you must select the option
Systeml . The default option ( Setup ) only asks for the password to access the Bios configuration.
View of the screen:
ROM PCI/ISA BIOS (2A69KACA)
CMOS SETUP UTILITY
AVARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURE SETUP
POWER MANAGEMENT SETUP
PnP/PCI CONFIGURATION
LOAD BIOS DEFAULTS
LOAD SETUP DEFAULTS
Esc: Quit
F10: SAVE & EXIT SETUP
INTEGRATED TERMINALS
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
SAVE & EXIT SETUP
EXIT WITHOUT SAVING
: Select Item
(Shift)F2: Change Color
Change/Set/Disable
84
Procedure
Configuration of the Bios
The password modification procedure is as follows:
1 Select the type of password: SUPERVISOR or USER, using the direction keys:
Then press Enter
The following box appears:
ENTER PASSWORD:
2
Note: if you no longer require a password, simply press Enter
Enter your password and press Enter
The following box appears:
CONFIRM PASSWORD:
3
4
Enter your password again and press Enter
Press F10 to save and quit
85
Configuration of the Bios
86
Maintenance
9
At a Glance
Subject of this chapter
What's in this
Chapter?
This chapter covers maintenance of the computers from the Magelis iPC range.
This chapter contains the following topics:
Topic
Reinstallation
Replacing dust filters
Page
87
Maintenance
Reinstallation
At a Glance
Before reinstalling
In certain cases, it may be necessary to reinstall the operating system. The reinstallation procedure is given below.
Before reinstalling the operating system, make sure that the following equipment is at hand: l l l
A CD-ROM drive, for MPC AN•• reference Control Boxes
(Ref. MPC YN00 CDR 00N ).
The reinstallation CD-ROM that was provided with the product
The recovery disk
Note: Important : save all important data contained on the hard drive (the reinstallation process erases all data on the hard drive). The reinstallation process will return the computer to its factory settings.
Reinstallation Proceed as follows
3
4
1
2
Insert the recovery disk in the disk drive and power-up the computer.
Insert the reinstallation CD-ROM in the CD-ROM drive.
Follow the messages that appear on the screen.
Once installation is complete, remove the disk and the CD-ROM from their drives and restart the computer.
Specific drivers Specific drivers are available on the reinstallation CD-ROM. These drivers are already installed on your machine and should not need to be reinstalled.
88
Maintenance
Replacing dust filters
At a Glance
Accessing the filters
It is necessary to regularly check the condition of the Control Boxes' dust filters, in order to clean or change them if they are very dirty.
View of the filters' location:
Note: On MPC AN•• reference Control Boxes, a third filter is located on the blower at the rear of the product.
89
Maintenance
90
Installation
At a Glance
Subject of this part
What's in this
Part?
This part concerns product installation.
This part contains the following chapters:
Chapter
10
11
Chapter Name
Dimensions/Assembly
Connections
III
Page
91
Installation
92
Dimensions/Assembly
10
At a Glance
Subject of this chapter
What's in this
Chapter?
This chapter concerns the dimensions and the panel mounting of products.
This chapter contains the following topics:
Topic
Dimensions of the front panels
Other dimensions
Cropping for cabinet installation
Panel mounting
Mounting in 19" rack
Mounting without a front panel
Page
93
Dimensions/Assembly
Dimensions of the front panels
At a Glance The dimensions of the four types of front panels are provided below (in mm).
Front panels with
12" screen
Front panels with touch sensitive pad:
380
Front panels with keyboard:
410
94
Front panels with
15" screen
Front panels with touch sensitive pad:
460
Dimensions/Assembly
Front panels with keyboard:
480
95
Dimensions/Assembly
Other dimensions
At a Glance
MPC AN•••
The dimensions of the products equipped with a front panel are provided below (in mm).
With a 12" touch-sensitive screen front panel: MPC NT20 ••
360 138.9
Rear view
310 8
290
96
Dimensions/Assembly
With a 15" touch-sensitive screen front panel: MPC NT50 ••
440 138.9
Rear view
310 8
290
With a 12" screen front panel (touch-sensitive or non-touch-sensitive) and keyboard:
MPC NA20 •• or MPC NB20 ••
390 138,9
Rear view
310 8
290
97
Dimensions/Assembly
With a 15" screen front panel (touch-sensitive or non-touch-sensitive) and keyboard:
MPC NA50 •• or MPC NB50 ••
450 138.9
Rear view
310 8
290
98
MPC BN••• With a 12" touch-sensitive screen front panel: MPC NT20 ••
360 229.2
Dimensions/Assembly
Rear view
310 8
290
With a 15" touch-sensitive screen front panel: MPC NT50 ••
440 229.2
Rear view
310 8
290
99
Dimensions/Assembly
With a 12" screen front panel (touch-sensitive or non-touch-sensitive) and keyboard:
MPC NA20 •• or MPC NB20 ••
390 229.2
Rear view
310 8
100
290
With a 15" screen front panel (touch-sensitive or non-touch-sensitive) and keyboard:
MPC NA50 •• or MPC NB50 ••
450 229.2
Rear view
310 8
290
MPC CN••• With a 12" touch-sensitive screen front panel: MPC NT20 ••
360 302.7
Dimensions/Assembly
Rear view
310 8
290
With a 15" touch-sensitive screen front panel: MPC NT50 ••
440 302.7
Rear view
310 8
290
101
Dimensions/Assembly
With a 12" screen front panel (touch-sensitive or non-touch-sensitive) and keyboard:
MPC NA20 •• or MPC NB20 ••
390 302.7
Rear view
310 8
102
290
With a 15" screen front panel (touch-sensitive or non-touch-sensitive) and keyboard:
MPC NA50 •• or MPC NB50 ••
450 302.7
Rear view
310 8
290
Dimensions/Assembly
Cropping for cabinet installation
At a Glance For cabinet installations, it is necessary for products to be cropped. The dimensions of the crop to be performed (in mm) depend on the type of front panel used.
Crop dimensions 12" screen without keyboard
12" screen with keyboard
Crop dimensions
362
392
103
Dimensions/Assembly
15" screen without keyboard
Crop dimensions
15" screen with keyboard
Crop dimensions
442
452
104
Dimensions/Assembly
Panel mounting
At a Glance
Illustration
The products and their front panels are designed to be attached to the door of a cabinet. Products can be mounted as described below.
Attachments*
Seal
Affix the MPC to the panel using the attachments as shown.
105
Dimensions/Assembly
Mounting in 19" rack
Introduction A front panel with 15" screen can be mounted in a 19" rack. This mounting uses brackets available in the catalogue (Ref. no. MPC YN00 RMK 00N ).
View of a front panel mounted in a 19" rack:
Mounting View of a front panel mounted using attachment brackets
Attachment
Brackets
106
Mounting recommendations
Dimensions/Assembly
To facilitate the insertion of a CD-ROM and a diskette, the support used must be no thicker than 2.5 inches, see figures below:
Overhead view:
<63mm
CD-ROM/disk drive
Back view:
CD-ROM/disk drive
<63mm
107
Dimensions/Assembly
Mounting without a front panel
At a Glance
Mounting
It is possible to use a Control Box with a video monitor and external keyboard instead of a front panel. Here, the connection base accessory MPC NP00 NNN 00N is used as an attachment and front panel connector cover.
View of a Control Box mounted on a Telequick AM1 PA plate:
108
Mounting distance: 330 mm
Procedure:
1
2
Assemble the Control Box connection base using the 12 cross-slot screws supplied.
Attach the assembly to the plate using the four screws
Connections
11
Connection to PLCs
Introduction
Nano, Micro,
Premium
Series 7
TSX 17
Different connection cables are used depending on the PLC. These are specified below.
This connection requires the use of connection cable TSX PCX 1031 or TSX PCX
3030 supplied with PL7 Pro and PL7 Junior software.
This 2 meter-long cable is equipped with the following: l l
A 9-contact SUB-D-type female connector, for connection to the Magelis iPC
(TSXPCX 1031) or a USB connector for connection to the Magelis iPC (TSX PCX
3030).
A 5-contact microDin-type male connector for connection to the PLC.
This concerns TSX 27 PLCs, and TSX/PMX 47/67/87/107 PLCs.
This connection requires the use of connection cable FT20CBCL30 supplied with
XTEL Pack software.
This 2.5 meter-long cable is equipped with the following: l l
A 9-contact SUB-D- type female connector for connection to the Magelis iPC.
A 9-contact SUB-D-type male connector for connection to the PLC.
TSX 17 PLCs are connected via an accessory for converting the COM1 link (RS
232) into a RS 485 link (to be ordered separately).
Accessory reference number: TSX 17 ACC PC
109
Connections
April 2000/30000 This connection requires the use of connection cable TSX PKIT 2040 (to be ordered separately).
This 2 meter-long cable is equipped with the following: l l
A 9-contact SUB-D- type female connector for connection to the Magelis iPC.
A 9-contact SUB-D-type male connector for connection to the PLC.
110
Appendices
IV
At a Glance
Subject of this part
What's in this part?
This part contains the appendices relating to the products.
This Part contains the following Chapters:
Chapter
12
Chaptername
Accessories
Page
111
Installation
112
Accessories
12
Accessories
List Accessories are available as options. The list of accessories is shown below:
Description
Connection base used when the Control Box is used without a front panel
12" external LCD monitor
15" external LCD monitor
17" external LCD monitor
Swivel arm for LCD monitor
Industrial external keyboard
Optional CD-ROM drive for MPC NA••
100W AC power supply for MPC NB••
230W AC power supply for MPC NC••
100W 24V DC power supply for MPC NB••
300W 24V DC power supply for MPC NB••
3 slot block for extension cards
6 slot block for extension cards
CD-ROM and disk drive sub assembly for MPC NB/NC
64 Mb Control Box Ram extension
128 Mb Control Box Ram extension
256 Mb Control Box Ram extension
Set of 19" fastening brackets for 15" screen front panel
Maintenance kit (seal, screws, filters) 12" touch screen
Maintenance kit (seal, screws, filters) 12" keyboard
Maintenance kit (seal, screws, filters) 15" touch screen
Maintenance kit (seal, screws, filters) 15" keyboard
Reference
MPC NP0 0NNN 00N
MPC YS2 0NNN 00N
MPC YS5 0NNN 00N
MPC YS8 0NNN 00N
MPC YN0 0ARM 00N
MPC YN0 0KBD 00N
MPC YN0 0CDR 00N
MPC YN0 0PWS ACM
MPC YN0 0PWS ACL
MPC YN0 0PWS DCM
MPC YN0 0PWS DCL
MPC YN0 0SLT 003
MPC YN0 0SLT 006
MPC YN0 0DRV 00N
MPC YN0 0RAM 064
MPC YN0 0RAM 128
MPC YN0 0RAM 256
MPC YN0 0RMK 00N
MPC YN2 0MNT KIT
MPC YN2 KMNT KIT
MPC YN5 TMNT KIT
MPC YN5 KMNT KIT
113
Accessories
114
Advertisement