Alpine iLX-F309TND Halo9 Multimedia Receiver Installation Manual

iLX-F309TND

Toyota Tundra

˜ 1/19

Toyota Tundra iLX-F309TND

9” Restyle In-Dash System

Installation Manual

˜

Model: Tundra

˜

Model Year: 2014-Up

Toyota

Model

Tundra

Year

2014 - Up

* The specified vehicles have been tested and have met compatibility specs at the time of testing. Compatibility is not guaranteed if the manufacturer has made production changes to the listed vehicles above.

Warning: Before you begin wiring, remove the ground wire from the negative terminal of the battery. Failing to do so can lead to electric shock, injury or damage to equipment.

Introduction

˜ Congratulations on purchasing the iLX-F309TND. This installation manual is designed to take you through the step-by-step installation of iLX-F309TND into a 2014-Up Toyota Tundra. Please familiarize yourself with the owners manual and if you still have additional questions please call 1-800-TECH-101.

Note

˜ Design and specifications are subject to change without notice for improvement.

To Ensure Safe Use, Always Follow These Precautions

˜ The installation of this product requires specialized skills and experience. We recommend that you have the product installed by an Alpine authorized dealer.

˜ Before you use this product, be sure to carefully read this installation manual and the separate user's manual so that you can use the product correctly. Alpine Electronics bears no responsibility for problems that arise as a result of failure to follow the instructions in the manuals.

˜ This manual includes a number of symbols that are intended to help you use the product safely, to prevent harm to you and others, and to protect against damage to property. These symbols and their meanings are listed below. Make sure you fully understand these symbols before you begin reading the main text.

Explanations of Injury and Damage That May Result from Incorrect Use

Warning

Caution

Ignoring the content marked by this indication and using the product incorrectly is expected to lead to death or serious injury.

Ignoring the content marked by this indication and using the product incorrectly is only expected to lead to injury or property damage.

Tools Required

Panel Removing Tool

Wire Cutters

Needle Nose Pliers

10mm Socket

Toyota Tundra iLX-F309TND

Phillips Screwdriver

˜ 2/19

Extension Ratchet

Flathead Screwdriver

Accessory List

Installation Kit Parts iLX-F309TND Radio Mounted In

Dash Bezel

Main Harness With Maestro

Module Plugged In

OBDII Adapter Cable

Bluetooth Mic Phillips Screws x 1 FM Antenna Adapter

GPS Antenna Adapter

Toyota Tundra iLX-F309TND

Satellite Radio Antenna Adapter OEM USB Adapter

˜ 3/19

Low Level RCA Adapter Cable Ties x 10 USB Extension Harness

Aux/Preout Harness Documents

Alpine

Registration Card

Quick

Reference

Guide

iLX-F309TND

Toyota Tundra

˜ 4/19

Programming the iDatalink Maestro Module

The Maestro module is pre-flashed already. This page is here in case the module needs to be flashed again.

1

INSTALL THE WEBLINK PLUG-IN

Go to:

idatalinkmaestro.com/plugin and follow the installation steps. The

Maestro module must be programmed specifically for each vehicle and radio. Take care to enter the correct vehicle information, factory options, head unit model, and head unit serial number.

The head units serial number is an alphanumeric value which is found on the head units label, underneath the bar code.

Review the System Requirements before installing.

2

REGISTER A WEBLINK ACCOUNT

Go to: idatalinkmaestro.com/register and complete the registration process.

A confirmation email will be sent to you requiring validation.

For existing customers, click log in.

If the plugin is already installed, the caution, “The plugin is already installed” appears. Please skip to step 2.

4

LOG INTO WEBLINK

Go to: idatalinkmaestro.com/login.

Enter your username and password, then click OK.

3

CONNECT YOUR MAESTRO MODULE

Use your Maestro module to connect to your PC.

5

PROGRAM YOUR MODULE

Follow the programming steps for your vehicle.

6

Once Programing is complete “FLASHING

COMPLETED!” will be displayed.

Proceed to the next page to complete installation.

NOTE: If serial number is invalid, Call ADS at

1-866-427-2999 with the serial number.

iLX-F309TND

Toyota Tundra

˜ 5/19

Factory Unit Disassembly Process

1

Use a panel removal tool to release clips of the cigarette lighter/AUX panel and remove it.

2

Use a panel removal tool to release the clips on the

HVAC control panel and remove it.

3

Use a 10mm socket to extract (4) 10mm screws below the radio.

4

Use a panel removal tool to release the clips on the upper section of the radio disconnect and remove it.

5

Use a panel removal tool to release screw cover on the driver’s side A pillar.

6

Extract a 10mm screw and remove the A pillar cover.

iLX-F309TND

Toyota Tundra

˜ 6/19

Factory Unit Disassembly Process (Continued)

7

Use a panel removal tool to release the clips on the door sill and remove it.

8

Remove the plastic nut on the driver’s kick panel and carefully lift the kick panel to remove it.

9

Use a 10mm socket to extract (2) 10mm screws from the driver’s side knee cover panel.

10

Use a panel removal tool to release the clips on the knee cover panel and remove it.

11

Use a panel removal tool to release the rear cover from the eyewear compartment and remove it.

12

Open the eyewear compartment to reveal (2) T20

Torx screws. Extract (4) Torx screws from the entire assembly and remove it.

iLX-F309TND

Toyota Tundra

˜ 7/19

Installation Instructions

1

Use the included 3mm Phillips screw to mount the microphone next to the eyewear compartment.

Note: Be sure to clear the motion path of the sun visor.

2

Route the microphone cable down the driver’s A pillar following the factory harness while securing the cable with the provided cable ties.

3

Connect the OBD2 connector cable to the OBD2 port below the driver’s side dashboard.

4

Route both the microphone and OBD2 cables to the radio cavity as shown below.

5

Connect the FM, GPS, USB and SAT radio adapters.

6

Connect the main harness to the radio and vehicle following the corresponding system wiring diagram on pages 8 or 9. Note: The Negative (-) battery terminal should remain disconnected until the installation is completed.

iLX-F309TND

Toyota Tundra

˜ 8/19

Installation Instructions (Continued)

7

Mount the iLX-F309TND using (2) 10mm factory screws. Note: Place the additional (2) 10mm screws in their respective location in case they are need in future applications.

8

Replace all removed components to their factory location and connect the Negative (-) battery terminal.

iLX-F309TND

iLX-F309TND Wiring Diagram W/O Factory Amplifier

To OBDII Connector

24-pin

Connector

To Vehicle Connectors

28-pin

Connector

Power/Speaker

10-pin Connector

Rear Speaker

6-pin Connector

Toyota Tundra

˜ 9/19

Black

Not

Used

Not

Used

10-Pin Chime 18-Pin

Red

Not

Used

Reset

Button

Connect to White

GPS Antenna Connector iDatalink MAESTRO Module

3-Pin

Black

Not

Used

Blue

Not

Used

(DO NOT

Make The

Mistake Of

Plugging The

Data

Connection

In Here)

4-Pin 10-Pin 3-Pin 4-Pin

*

If using

KAC-001 see page 16

FM Antenna Adapter

USB Adapter

GPS Antenna

Adapter

See page 12 for HDMI connection info

Main Harness

Camera Adapter iLX-F309 Source Unit

CAN I/F

USB

GPS

HDMI IN

SXM/DAB

PRE OUT W.REMOTE

POWER

ANTENNA

Blue Power Antenna

iLX-F309TND

iLX-F309TND Wiring Diagram With Factory Amplifier

To OBDII Connector

24-pin

Connector

To Vehicle Connectors

28-pin

Connector

Power/Speaker

10-pin Connector

Rear Speaker

6-pin Connector

Toyota Tundra

˜ 10/19

Black

Not

Used

Not

Used

10-Pin Chime 18-Pin

Red

Not

Used

Reset

Button

Connect to White

GPS Antenna Connector iDatalink MAESTRO Module

3-Pin

Black

Not

Used

Blue

Not

Used

(DO NOT

Make The

Mistake Of

Plugging The

Data

Connection

In Here)

4-Pin 10-Pin 3-Pin 4-Pin

*

If using

KAC-001 see page 16

FM Antenna Adapter

USB Adapter

GPS Antenna

Adapter

See page 12 for HDMI connection info

Main Harness

Camera Adapter iLX-F309 Source Unit

CAN I/F

USB

GPS

HDMI IN

SXM/DAB

PRE OUT W.REMOTE

POWER

ANTENNA

USE LOW LEVEL FOR

JBL® AMPLIFIED

SOUND SYSTEM

L R L R L R

L R

Blue Power Antenna

High-level speaker output will be unplugged and left unused.

iLX-F309TND

Toyota Tundra

˜ 11/19

Connection Of An External Amplifier

ANTENNA

CAN I/F

USB

GPS

SXM/DAB

HDMI IN

PRE OUT W.REMOTE

POWER

SUBW

FRONT OUT

REAR OUT

(Blue/White) REMOTE

(Red)

(White)

(Red)

(White)

(Red)

(White)

RCA Extension Cable (sold separately)

Remote Turn-On Lead (Blue/White)

Subwoofer RCA Connectors

Front Output RCA Connectors

Rear Output RCA Connectors

REMOTE ON

(Blue/White)

REMOTE ON

(Blue/White)

Amplifier for subwoofer

(sold separately)

To subwoofer input terminal

Subwoofer

To front input terminal

Amplifier 4 ch

(sold separately)

To rear input terminal

Front speaker

Rear speaker

Connecting A SiriusXM Module (Sold Separately)

CAN I/F

USB

GPS

SXM/DAB

HDMI IN

PRE OUT W. REMOTE POWER

There is no way to integrate the factory SiriusXM tuner. Once the radio is removed, the factory

SiriusXM is removed. As the title states, SiriusXM requires a tuner sold separately. This diagram shows how to integrate the antenna connection.

For vehicles with factory SiriusXM connect the adapter to the factory SiriusXM antenna in the radio cavity. The included adapter is just for the antenna. That antenna plugs into the aftermarket module that you purchase. For vehicles without factory SiriusXM use the antenna that is included with the SXV300 SiriusXM Tuner.

iLX-F309TND

Toyota Tundra

˜ 12/19

iLX-F309TND HDMI Input

Do not use the head unit’s

USB to power HDMI devices.

This port is meant for Apple

CarPlay, Android Auto, and

USB flash drives.

iLX-F309 Source Unit

CAN I/F

GPS

SXM/DAB

USB

HDMI IN

PRE OUT EXT. KEY W.REMOTE

POWER

ANTENNA iPhone

For iPhone the

Lightning to HDMI adapter

is required

For all phones the USB power source needs to be a 2A source. This will require a separate USB power source to be installed in the vehicle.

Android Phone

For Android users most

Android phones do not have

HDMI adapters. The easiest way to connect is with a Miracast adapter

(for example a Roku Stick or Amazon Firestick).

Or

Or

DVE-5300 DVD Player

When using the DVE-5300 with the iLX-F309 only the remote can be used to control the DVD player.

iLX-F309TND Wiring Diagram

PRE OUT cable

Interface cable

Power cable

W.REMOTE cable

SPEED SENSOR

(Green/White)

CAMERA

IDATALINK I/F

AUX INPUT

REMO

(Blue/White)

REVERSE

(Orange/White)

P. ANT

(Blue)

PARKING BRAKE

(Yellow/Blue)

ACC

(Red)

BATT

(Yellow)

GND

(Black)

(Green)

(Green/Black)

(White)

(White/Black)

(Gray/Black)

(Gray)

(Violet/Black)

(Violet)

STEERING REMOTE

MIC IN

SUBW

FRONT OUT

REAR OUT iLX-F309TND

Toyota Tundra

˜ 13/19

To SiriusXM Tuner

Vehicle Antenna

GPS Antenna (Included)

To the vehicle speed pulse line

To Front, Rear or Side camera

To iDataLink module

To AUX output device or iDataLink module

To amplifier or equalizer

To plus side of the back lamp signal lead of the car

To power antenna

To the parking brake signal lead

Ignition key

Battery

Rear Left

Front Left

Front Right

Speakers

Rear Right

To remote control input lead of

DVE-5300

To remote control input lead of Rear

Monitor

To remote control output lead

To remote control input lead

To remote control output lead of

DVE-5300

To steering remote control interface box

Microphone (Included)

To input terminal of amplifier when adding an external amplifier

iLX-F309TND

Toyota Tundra

˜ 14/19

Wire Harness Pin Outs

5

4

3

2

1

8

7

6

Radio Main

16

15

14

13

12

11

10

9

Blue 22AWG

Red 20AWG

Blue/White 22AWG

Orange/White 22AWG

Yellow/Blue 22AWG

Purple 20AWG

Gray 20AWG

Purple/Black 20AWG

Gray/Black 20AWG

Green 20AWG

White 20AWG

Green/Black 20AWG

White/Black 20AWG

Yellow 18AWG

Black 18AWG

OEM Speaker Harness 1

6 5

4

3

1 2

Green 22AWG

Green/Black 22AWG

White/Red 22AWG

Violet 22AWG

Violet/Black 22AWG

Remote Harness

5

3

1

11

9

7

6

4

2

12

10

8

White 22AWG

Black 22AWG

Cam Aux Data

17

15

13

11

18

16

9

7

5

3 4

1 2

8

6

14

12

10

OEM Speaker Harness 2

Yellow 18AWG

9 10

Orange 22AWG

Red/Black 22AWG

7 8

Blue/White 22AWG

6

5

White/Red 22AWG

3 4

1 2

Black 18AWG

White 22AWG

White/Black 22AWG

Grey 22AWG

Grey/Black 22AWG

Speaker Harness

4

3

1

2

Speaker Harness

4

3

1

2

Toyota Radio 1

17

16

15

14

13

20

19

18

24

23

22

21

8

7

6

5

4

3

2

1

12

11

10

9

Brown/Red 22AWG

Brown/Yellow 22AWG

Green/Red 22AWG

Green/Yellow 22AWG

Black 22AWG

Blue/Yellow 22AWG

Black 22AWG

Yellow 22AWG

Violet/White 22AWG iDatalink

3

4

1

2

Data SWC

5

7

1 2

3 4

6

8

9 10

11 12

13 14

15 16

17 18

Blue 22AWG

White 22AWG

Black 22AWG

Red 22AWG

Power/ACC

3

2

1

Orange 22AWG

Green/Red 22AWG

Green/Yellow 22AWG

Gray/Red 22AWG

Blue/White 22AWG

Red 22AWG

Yellow/Brown 22AWG

Red/Brown 22AWG

Brown/Yellow 22AWG

Red/White 22AWG

Violet/Red 22AWG

Yellow 18AWG

Red 18AWG

Black 18AWG

Yellow 22AWG

Red 22AWG

Black 22AWG

White 22AWG

White 22AWG

Black 22AWG

Black 22AWG

White 22AWG

Green/White 22AWG

Red 22AWG

Purple 20AWG

Purple/Black 20AWG

Green 20AWG

Green/Black 20AWG

Gray 20AWG

Gray/Black 20AWG

White 20AWG

White/Black 20AWG

Toyota Radio 2

14

13

12

11

10

9

8

7

6

5

4

3

2

1

22

21

20

25

24

23

28

27

26

19

18

17

16

15

Black 20AWG

Yellow 20AWG

Violet/Pink 22AWG

Green/Red 22AWG

Pink/Red 22AWG

Green/Yellow 22AWG

Black 22AWG

Red/Brown 22AWG

Yellow/Brown 22AWG

Orange 22AWG

Black 22AWG

Black/Yellow 22AWG

Red 22AWG

Black 22AWG

White 22AWG

Audio In

3

5

1 2

4

6

7 8

9 10

White/Red 22AWG

Red/Black 22AWG

Yellow/Black 22AWG

Pink 22AWG

Green 22AWG

Yellow/Green 22AWG

Blue/White 22AWG

Black/Yellow 22AWG

iLX-F309TND

Toyota Tundra

˜ 15/19

Adding A Front Camera

To use the OEM camera the RCA will need to be extended to the “Other” input on the KCX-C2600B.

RCA Camera Input

Main Harness

KCX-C2600B

(Sold Separately) iLX-F309 Source Unit

CAN I/F

GPS

USB

HDMI IN

SXM/DAB

PRE OUT W.REMOTE

POWER

ANTENNA

1 2 3 4 5 6

1 - V. Out

2 - Other Camera

3 - Front Camera

4 - Rear Camera

5 - Switch

6 - Power Wires

Reverse Out (Orange/Black)

Reverse In

(Orange/White)

Accessory (Red)

Battery (Yellow)

Ground (Black)

Toggle Switch

*Only one rear camera can be used for a total of 2 cameras

(one front and one rear). The direct input will always take precedence over the RCA input. If the vehicle has an OEM camera that would plug into the “Other” port. You can’t use a direct to RCA adapter for it.For the front camera an Alpine camera with the direct connection is recommended. Using a 3rd party camera with a direct to RCA adapter can’t be guaranteed to work.

Alpine Direct Rear Camera*

Alpine Direct Front Camera

Connection Of KAC-001 (Sold Separately)

KAC-001 Side View

POWER RESET HEADUNIT CAN OUTPUT iLX-F309TND

UPDATE

Reset

Button

USB port

(Firmware updates only)

Toyota Tundra

˜ 16/19

BATT* (Yellow)

ACC (Red)

GND (Black)

*Fuse Rating: 7A cable from head unit. This is the 4 pin data connector comes directly off of the main harness

3 Pin

Black

Interface Cable (4-pin) (included with ADS module)

Output 1 (Purple)

Output 2 (White/Red)

Output 3 (Brown)

Output 4 (Blue)

Output 5 (Green)

Output 6 (Pink)

Output 7 (White)

Output 8 (Gray)

Connect to Relay/output to accessories (Sold separately)

Maestro Module Side View

To 4 Pin Black Data

4 Pin

Blue

10 Pin

Green

3 Pin

Black

4 Pin

Black Data

Not

Used

To Head Unit

iLX-F309TND

Toyota Tundra

˜ 17/19

Steering Wheel Configuration

Right

Up

Left

Enter

Down

Back

Mode/Hold

Volume Up

Volume Down

MODE

HOLD

Off Hook

On Hook

Voice

Button

Right

Up

Left

Enter

Down

Back

Mode/Hold

Volume Up

Volume Down

Off Hook

On Hook

Voice

Press Once

Display Guages Screen

Seek +

Display Vehicle Screen Info

Phone Menu

Seek -

Band

Source

Volume +

Volume -

Answer Call

Hang Up & Reject Call

Voice or Siri

Press And Hold

None

Preset & Folder +

None

None

Preset & Folder -

None

None

None

Attenuation On/Off

None

None

None

iLX-F309TND

Toyota Tundra

˜ 18/19

Set Up Guide

1

Turn the vehicle’s Ignition switch to ACC.

2

Turn ON the iLX-F309TND by pressing any key.

3

Select the user language and press OK.

4

Engage and release the parking brake twice (parking brake on, off, and back on).

5

If a camera is present, turn it ON in the system menu. (MENU/SETUP/SYSTEM/CAMERA/CAMERA SELECT).

6

AUDIO MUTE ON REVERSE- By default, when the vehicle is shifted into reverse the AUDIO will MUTE. If this feature is not desired turn it off in the AUDIO MENU (MENU/SETUP/SOUND/MUTE WHILE BACKING UP).

7

When the KAC-001 (External Accessory Control Module) is present be sure to turn it ON in the SETUP MENU.

(MENU/SYSTEM/EXTERNAL ACCESSORIES/EXTERNAL ACCESSORY CTLR).

8

Vehicle information- Set the desired gauge information. (MENU/VEHICLE INFO/GAUGES/CAR SETTINGS).

9

NOTE: For all the product information please download the full owners manual in the support section of the website at www.alpine-usa.com.

Troubleshooting Guide

Symptom

1

2

3 iPhone not working with

HDMI.

Android phone is not working with HDMI.

Miracast adapter isn’t plugged into a 2A source.

iDatalink website says serial number is invalid.

Possible Cause

Not using Apple HDMI to Lightning adapter.

Didn’t plug USB power into a 2A source.

Using incorrect HDMI adapter.

Miracast adapter has resolution settings that are too high.

Incorrect serial number is being used.

Serial number may not be in iDatalink database.

Remedy

Purchase the HDMI to Lightning adapter directly from Apple. Not all 3rd party adapters work the same.

Do not plug into the USB from the Alpine head unit. A third party USB adapter will need to be used that is 2A.

If the phone has the feature to use an HDMI adapter it must be the one purchased from the manufacturer of the phone, not a third party adapter.

Do not plug into the USB from the Alpine head unit. A third party USB adapter will need to be used that is 2A.

Plug the adapter into another monitor (for example a television in the home) and reduce the resolution settings.

In the iLX-F309TND settings confirm the serial number. MENU/SETUP/GENERAL/

ABOUT.

Call ADS at 1-866-427-2999 and verify.

iLX-F309TND

Toyota Tundra

˜ 19/19

Troubleshooting Guide Continued

Symptom

4

Headunit will not turn on.

Possible Cause

Incorrect serial number was used when flashing maestro.

4 pin Maestro data cable is disconnected or damaged.

OBD2 cable is not plugged in.

Monitor, power plate screw, or main harness are not connected.

5

Cannot enter SETTINGS

MENU.

Vehicle is in motion or parking brake is not engaged.

6

7

Remedy

Flash Maestro with correct serial number.

Check for proper connection or disconnected pins.

Connect OBD2 connector to the OBD2 port.

Check for proper connection or disconnected pins.

With vehicle in (P)PARK engage the parking brake. Release the parking brake and engage the parking brake a second time, as shown in the Setup Guide on page 18.

The DVE-5300 (sold separately) can only be controlled by the wireless remote that is included with it.

Change Mute on reverse to off.

8

9

10

Cannot control the DVD

Player properly.

Sound mutes when vehicle is shifted into reverse.

Only the front speakers are on for SXM Radio.

CarPlay, Android Auto, or off-road navigation map positioning issues.

CarPlay, Android Auto, or off-road navigation vehicle position icon heading in wrong direction

The iLX-F309TND does not have remote wires.

Mute on reverse is turned on in the

SOUND menu.

SXM Tuner has not been activated.

GPS antenna is positioned incorrectly.

Reverse Signal is not connected or not reliable.

Loose or disconnected USB cable.

Activate SXM Tuner.

GPS antenna is obstructed and doesn’t have line of sight to the sky. Perform a factory reset. The unit will automatically recalibrate.

Ensure that Reverse wire is connected. Also ensure that no 3rd party interface module(s) interfere with the Reverse Signal. The head unit uses the Reverse Signal to achieve optimal positioning performance.

Check the USB connection behind the headunit.

11 iPhone or Android phone is not recognized when connected to the

USB cable.

Non-compatible cable.

Use the cable supplied with the iPhone or Android phone. Third party adapters and long extensions may not work.

Only use USB extension that came with the head unit.

Dirty charging port on phone.

Clean charging port.

12 No output from RCA’s.

Maestro module is flashed for amplied system.

13

Volume controls on bezel and steering wheel controls do not work.

The setting for External Processor was turned on.

Re-flash module for non-amplified system.

That setting should only be checked when using an external sound processor. When there isn’t one being used in the audio system it needs to be in the default setting of off. MENU/SETUP/SYSTEM/EXTERNAL

ACCESSORIES/EXTERNAL AUDIO

PROCESSOR/OFF