Earthquake E43™ Earth Auger Powerhead Operator's Manual
Advertisement
Advertisement
e43 earth auger powerhead operator’s manual
GetEarthquake.com
Also includes CE model E43CE
OME43
Rev. 06/30/10
© Copyright 2010 Ardisam, Inc.
All Rights Reserved.
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
thank You and congratulations....
on your purchase of a new EARThqUAkE® POWERhEAd from Ardisam, Inc. We have worked to ensure that your Earthquake Powerhead will be one of the most trouble-free and satisfying pieces of equipment you have ever owned. With proper care, your powerhead will provide many years of service. Please take the time to read this manual carefully to learn how to correctly operate and maintain your equipment.
INTROdUCTION
OWNER’S RESPONSIBILITY
Accurate assembly and safe and effective use of the powerhead is the owner’s responsibility.
• Read and follow all safety instructions.
• Carefully follow all assembly instructions.
• Maintain the powerhead according to directions and schedule included in this Earthquake operators manual.
• Ensure that anyone who uses the powerhead is familiar with all controls and safety precautions.
CONTENTS
Introduction & Registration .............................................................................................................................................2
Safety ......................................................................................................................................................................... 3-4
Operation .................................................................................................................................................................... 5-8
Maintenance & Storage ............................................................................................................................................ 9-12
Troubleshooting ............................................................................................................................................................13
Parts Diagrams & Parts Lists .................................................................................................................................. 14-17
Warranty ................................................................................................................................................................. 18-19
EC Declarations of Conformity ............................................................................................................................... 20-21
REGISTRATION
Record your model number and serial number in the space provided for easy reference. Fill out and mail the registration card located in your parts packet. Warranty is valid only if your completed registration card is received by Ardisam, Inc., at time of purchase.
Model Number
Serial Number
Date of Purchase
Place of Purchase
FEdERAL EMISSION INFORMATION
Ardisam, Inc. warrants to the retail purchaser, that this small, off-road engine was designed, built and equipped to conform at the time of initial sale to all applicable regulations of the U.S. Environmental Protection Agency (EPA).
Page 800-345-6007
GetEarthquake.com
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
SAFETY
OWNER’S RESPONSIBILITY
Accurate assembly and safe and effective use of the auger is the owner’s responsibility.
• Read and follow all safety instructions.
• Carefully follow all assembly instructions.
• Maintain the auger according to directions and schedule included in this Earthquake operator’s manual.
• Ensure that anyone who uses the auger is familiar with all controls and safety precautions.
SPECIAL MESSAGES
Your manual contains special messages to bring attention to potential safety concerns, machine damage as well as helpful operating and servicing information. Please read all the information carefully to avoid injury and machine damage.
note: general information is given throughout the manual that may help the operator in the operation or service of the machine.
IMPORTANT SAFETY PRECAUTIONS
Please read this section carefully.
Operate the auger according to the safety instructions and recommendations outlined here and inserted throughout the text. Anyone who uses this auger must read the instructions and be familiar with the controls.
This symbol points out important safety instructions which if not followed could endanger your personal safety. Read and follow all instructions in this manual before attempting to operate this equipment.
• Do not carry the auger powerhead between holes with the engine running.
• The auger should not rotate when the engine is idling. If it does rotate when engine is idling, contact Ardisam,Inc. for instructions.
• Always keep hands, feet, hair and loose clothing away from any moving parts on engine and auger.
• Always wear a protective hearing device.
• Do not allow children to operate this power auger. Do not allow adults to operate the auger without proper instruction.
• Do not operate any power equipment under the influence of alcohol or drugs.
• Keep all screws, nuts and bolts tight.
• Engine should be turned off and cool, spark plug wire must be removed from spark plug before any repairs are attempted.
• Temperature of muffler and nearby areas may exceed 150º F (65º C).
Avoid these areas.
• Never run engine indoors or in an enclosed area. Engine exhaust contains carbon monoxide, an odorless and deadly gas.
• If the earth auger will not turn in a hole, turn engine off and allow to cool before attempting to remove it manually.
• Use only original equipment parts from Ardisam including all nuts and bolts.
800-345-6007
GetEarthquake.com
WARNING
WARNING INdICATES A hAZARd WhICh, IF NOT AVOId-
Ed, COULd RESULT IN dEATh OR SERIOUS INJURY
ANd/OR PROPERTY dAMAGE.
CAUTION
CAUTION INdICATES YOU CAN CAN BE hURT OR YOUR
EqUIPMENT dAMAGEd IF ThE SAFETY INSTRUCTIONS
ThAT FOLLOW ThIS SIGNAL WORd ARE NOT OBEYEd.
IMPORTANT
INdICATES hELPFUL INFORMATION FOR PROPER AS-
SEMBLY, OPERATION, OR MAINTENANCE OF YOUR
EqUIPMENT.
WARNING
CALIFORNIA PROPOSITION 65 WARNING
ENGINE ExhAUST FROM ThIS PROdUCT CONTAINS
ChEMICALS kNOWN TO ThE STATE OF CALIFORNIA
TO CAUSE CANCER, BIRTh dEFECTS, OR OThER RE-
PROdUCTIVE hARM.
Below are two of the warning decals attached to the auger.
It is important to read all safety precautions and locate the warning labels before using this product.
WARNING!
Failure to read, understand and follow all warnings and instructions listed could result in serious injury or death. Keep all body extremities, loose clothing and foreign objects clear of rotating auger. Be sure auger is securely attached to powerhead during use. Never carry auger between holes with the engine running.
This auger is not designed to be utilized as an anchoring device.
Use this auger/powerhead as per provided instructions only.
LBLAUGER Rev. 04/24/08
!
WARNING!
Auger blades are EXTREMELY SHARP .
To avoid injury USE CAUTION when removing or replacing blades or guards.
LBLBPE
Page 3
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
ENGINE SAFETY PRECAUTIONS
WARNING CARBON MONOxIdE POISONING
All engines contain carbon monoxide in their exhaust. Carbon monoxide is a deadly, colorless, tasteless, odorless gas which may be present even if you do not smell or see any engine exhaust. Levels of carbon monoxide, which can be deadly, can be present for days in an enclosed area that has poor ventilation. Any level of carbon monoxide, if inhaled, can cause headaches, drowsiness, nausea, dizziness, confusion and eventually death. If you experience any of these symptoms, seek fresh air and medical attention immediately.
PREVENTING CARBON MONOxIdE POISONING
• Never run engine indoors.
• Never try to ventilate engine exhaust indoors. Carbon monoxide can reach dangerous levels very quickly.
• Never run engine outdoors where exhaust fumes may be pulled into a building.
• Never run engine outdoors in a poorly ventilated area where the exhaust fumes may be trapped and not easily taken away. (Examples include: in a large hole or areas where hills surround your working area.)
• Never run engine in an enclosed or partially enclosed area.
(Examples include: buildings that are enclosed on one or more sides, under tents, car ports or basements.)
• Always run the engine with the exhaust and muffler pointed in the direction away from the operator.
• Never point the exhaust muffler towards anyone. People should always be many feet away from the operation of the engine and its attachments.
GASOLINE FIRES OR hANdLING FUEL SAFELY
Fuel and fuel vapors are highly flammable. Never use fuel where a spark or flame may be present. Never use fuel where a potential source of ignition could occur. (Examples include: hot water or space heaters, clothes dryer, electric motors, etc.)
Keep flames and sparks away from engine and fuel to prevent fires. Fuel fires spread very quickly and are highly explosive.
PREVENTION OF GASOLINE FIRES
• Never fill your fuel tank with fuel indoors. (Examples include: basement, garage, barn, shed, house, porch, etc.)
• Always fill fuel tank outside in a well ventilated area.
• Never remove the fuel cap or add fuel with the engine running. Stop engine and allow to cool before filling.
• Never drain fuel from engine in an enclosed area.
• Always wipe up excess (spilled) fuel from engine before starting. Clean up spilled fuel immediately.
• Allow spilled fuel to dry, after wiping and before starting.
CAUTION hOT GASES ARE A NORMAL BY-PROdUCT OF A FUNC-
TIONING CATALYTIC CONVERTER. FOLLOW ALL SAFE-
TY INSTRUCTIONS TO PREVENT BURNS ANd FIRES.
• Allow fuel fumes/vapors to escape from the area before starting engine.
• Test the fuel cap for proper installation before starting and using engine.
• Always run the engine with fuel cap properly installed on the engine and gas cap vent screw unscrewed.
• Replace fuel cap that allows gas to spill or leak.
• Never smoke while refilling engine fuel tank.
• Prevent fire and explosion caused by static electric discharge. Use only non-metal, portable fuel containers approved by the Underwriter’s Laboratory (U.L.) or the
American Society for Testing & Materials (ASTM).
• Do not store engine with fuel in fuel tank indoors. Fuel and fuel vapors are highly explosive.
• When storing, screw down gas cap vent screw tightly.
• Never pour fuel from engine fuel tank.
• Never siphon fuel by mouth to drain fuel tank.
• Always have an adult fill the fuel tank.
• Never allow an adult or anyone under the influence of drugs or alcohol to fill engine.
• Never allow children to fill the engine.
BURNS ANd FIRES
The muffler, muffler guard and other parts of the engine become extremely hot during the operation of the engine. These parts remain extremely hot after the engine has stopped.
PREVENTION OF BURNS ANd FIRES
• Never remove the muffler guard from the engine.
• Never touch the muffler guard because it is extremely hot and will cause severe burns.
• Never touch parts of the engine that become hot after operation.
• Always keep materials and debris away from muffler guard and other hot parts of the engine to avoid fires.
This engine is designed to operate using a catalytic converter which contributes to the engine’s compliance with the EPA.
Page 4 800-345-6007
GetEarthquake.com
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
OPERATION
STEPS FOR WORkING ON ENGINE OR AUGER
1. Turn off engine switch.
2. Disconnect the spark plug wire from the spark plug.
3. Securely place the disconnected spark plug wire away from the spark plug and any metal parts. This must always be done or arcing may occur between spark plug wire and metal parts.
4. Replace or repair the part on the engine or auger.
5. Check all parts that were repaired, or removed during repair, that they are secure and fit correctly.
note: all repair parts must come from the factory. never replace parts that are not specifically designed for the engine or auger.
6. Replace spark plug wire.
PREPARING ENGINE FOR STARTING
Before starting your powerhead engine, make sure the black throttle cable housing is seated all the way into the brass ferrule at the engine side of the cable.
GAS ANd OIL qUALITY
To operate the engine, we recommend using “VIPER” brand 2-cycle oil
(PN 300400) to ensure that the engine operates correctly throughout the life of the engine. Use unleaded regular gas only.
NOTE: VIPER oil can be purchased from our web site at www.
getearthquake.com.
MIxTURE
Run earth auger with a 50:1 ratio.
GAS
1 gallon
2 gallons
5 gallons
OIL
2.5 ounces
5 ounces
13 ounces
RATIO
50:1
50:1
50:1
MIxING FUEL ANd FILLING GAS TANk
MIxING FUEL
1. Fuel must be mixed in a container outside in a well ventilated area.
2. Fill certified fuel container 1/4 full of recommended fuel.
3. Add recommended amount of 2 cycle oil.
4. Screw container cap on straight and tight.
5. Shake the container to mix fuel and oil.
6. Unscrew gas cap slowly to vent, add the remainder of fuel requirements.
7. Wipe away any spilled fuel or oil and allow to evaporate before moving or transporting.
CAUTION dO NOT ALTER/MOdIFY ENGINE OR AUGER:
NEVER ALTER OR MOdIFY ThE ENGINE FROM ThE
FACTORY. SERIOUS INJURY OR dEATh MAY OCCUR IF
ENGINE IS MOdIFIEd OR ALTEREd.
WhEN WORkING ON OR REPLACING PARTS FOR ThE
ENGINE OR AUGER YOU MUST ALWAYS dISCONNECT
SPARk PLUG WIRE FROM ThE SPARk PLUG ANd kEEP
IT AWAY FROM ThE SPARk PLUG.
ALWAYS WEAR hEARING PROTECTION WhILE OPER-
ATING ENGINE.
PLEASE dO NOT START YOUR EARTh AUGER UNTIL
YOU hAVE REAd ThE PREVIOUS SECTION OF ThIS
MANUAL. IF YOU hAVE REAd ThESE, FOLLOW ThE
STEPS BELOW TO START YOUR EARTh AUGER.
NEVER STORE ENGINE WITh GAS IN ThE TANk INdOORS. FUEL ANd FUEL VAPORS ARE hIGhLY FLAM-
MABLE.
NEVER MIx FUEL ANd OIL dIRECTLY IN ENGINE GAS
TANk. USE ONLY NON-METAL, PORTABLE FUEL CON-
TAINERS APPROVEd BY ThE UNdERWRITER’S LABO-
RATORY (U.L.) OR ThE AMERICAN SOCIETY FOR TEST-
ING & MATERIALS (ASTM).
AN AdULT MUST ALWAYS hANdLE ANd FILL ThE EN-
GINE WITh FUEL.
ALWAYS hANdLE FUEL IN A WELL VENTILATEd AREA,
OUTdOORS, AWAY FROM FLAMES OR SPARkS.
IMPORTANT
ThIS ENGINE USES A GAS/OIL MIxTURE. dO NOT RUN
ON STRAIGhT GAS ONLY, ENGINE dAMAGE WILL RE-
SULT.
800-345-6007 Page 5
GetEarthquake.com
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
FILLING GAS TANk
1. Shut-off engine and allow engine to completely cool before refilling the gas tank.
2. Move to a well ventilated area, outdoors, away from flames and sparks.
3. Clean debris from area around the gas cap.
4. Loosen gas cap slowly. Place the cap on a clean, dry surface.
5. Carefully add fuel without spilling.
6. Do not fill gas tank completely full, allow space for fuel to expand.
7. Immediately replace gas cap and tighten. Wipe off spilled fuel and allow to dry before starting engine.
NORMAL OPERATION
1. The clutch will transfer maximum power after about two hours of normal operation. During this break-in period clutch slippage may occur. The clutch should be kept free of oil or other moisture for efficient operation.
2. Drill holes without placing excessive body weight on the unit.
The auger operates most efficiently with a shaving action caused by the weight of the unit itself.
3. Never run engine indoors. Exhaust fumes are deadly.
4. Do not use an earth auger in the ice.
5. To attach auger to powerhead, align hole at top of auger shaft with the output shaft hole. Insert 3/8-16 x 1-1/2” bolt and secure bolt with provided 3/8” bi-way lock nut using a wrench.
USING ThE SCREW TYPE, MANUAL VENTING GAS CAP
Your powerhead is equipped with a screw type, manual venting gas cap.
1. Before starting the engine, turn the screw in the top of the gas cap
2-3 turns (counterclockwise) to its venting position. dO NOT turn the screw to the point that it stops (4-5 turns counterclockwise).
To ensure that gas will not spill during use, check that the gas cap is screwed on tightly and the gas cap screw is in the venting position.
2. After using the power earth auger and before putting away or transporting it in a truck bed, screw the gas cap screw and gas cap on
(clockwise) tightly. This will prevent gas from leaking during storage.
The gas cap will not leak during storage if gas cap is tight and the screw at the top is tight. Note: When storing the unit upright for a period of time in hot weather, ventilate the fuel tank cap to prevent leaking fuel from the carburetor.
IMPORTANT NOTE: The handle bar vibration has a measured acceleration value that does not exceed .5 m/s . The measured sound power level measured from the operator’s position is 100 dBLWA and is guaranteed not to exceed 106 dBLWA. The mass of the powerhead is 9.9 kg. (1.7 lbs.)
CAUTION
ALWAYS hANdLE FUEL IN A WELL VENTILATEd AREA,
OUTdOORS, AWAY FROM FLAMES OR SPARkS. dO NOT START ENGINE IF FUEL IS SPILLEd. WIPE OFF
ExCESS FUEL ANd ALLOW TO dRY. REMOVE ENGINE
FROM AREA TO AVOId SPARkS.
Page 6 800-345-6007
GetEarthquake.com
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
STARTING ANd STOPPING ENGINE
• Move engine to a well ventilated area, outdoors, to prevent carbon monoxide poisoning.
• Move to an area away from flames or sparks, to avoid ignition of vapors if present.
• Remove all debris from air cleaner holes and gas cap to ensure proper air flow.
COLd ENGINE START
Starting engine for first time or after engine has cooled off or after running out of fuel.
1. Unscrew the screw from the cap vent on the gas tank (in a counterclockwise direction).
2. Move choke lever to RUN position.
NOTE: Choke must be in the RUN position when pushing or using the primer bulb.
3. Prime unit until primer hose is filled with gas.
NOTE: When using the primer bulb, allow the bulb to return completely to its original position between pushes.
4. Move choke lever to ChOkE position.
note: choke position is defined by moving the choke lever as far to the choke position as possible.
5. Push rocker switch to the ON position.
6. Squeeze throttle control with right hand. Grasp starter handle with left hand and pull out slowly, until it pulls slightly harder. Without letting starter handle retract, pull rope with a rapid full arm stroke.
Let it return to its original position very slowly until unit fires or runs.
Repeat this step every time the starter rope is pulled.
note: if engine fails to start after 5-6 pulls, push primer 1
time and pull starter rope again.
7. After engine starts running, move choke lever to hALF ChOkE position until unit runs smoothly.
note: half choke is defined when the choke lever is between CHOKE and RUN.
8. Move choke lever to RUN position and move throttle to desired speed.
NOTE: Run at full throttle when possible. Do not let unit idle for extended periods of time.
9. To stop engine, push rocker switch to OFF position.
WARNING
MAkE SURE ThE UNIT IS IN A STABLE POSITION BE-
FORE PULLING ThE STARTER hANdLE.
WhEN ThE UNIT STARTS TO FIRE OR RUN, RELEASE
ThE ThROTTLE CONTROL MOMENTARILY WITh YOUR
RIGhT hANd ANd RETURN YOUR LEFT hANd TO ThE hANdLEBAR POSITION TO MAINTAIN CONTROL ANd
STABILITY OF ThE UNIT WITh BOTh hANdS.
CAUTION
ALWAYS hANdLE FUEL IN A WELL VENTILATEd AREA,
OUTdOORS, AWAY FROM FLAMES OR SPARkS.
ALWAYS WEAR A PROTECTIVE hEARING dEVICE.
dO NOT START ENGINE IF FUEL IS SPILLEd. WIPE OFF
ExCESS FUEL ANd ALLOW TO dRY. REMOVE ENGINE
FROM AREA TO AVOId SPARkS.
IF AUGER IS MOUNTEd TO ENGINE, ALL SAFETY
GUARdS MUST BE SECURELY ON TO AVOId SERIOUS
INJURY.
STARTER ROPE CAN CAUSE AN UNANTICIPATEd JERk
TOWARdS ENGINE. PLEASE FOLLOW INSTRUCTIONS
TO AVOId INJURY.
IF ENGINE FAILS TO START AFTER TRYING STARTING
PROCEdURES, PLEASE CONTACT OUR CUSTOMER
SERVICE dEPARTMENT AT 800-345-6007.
NEVER LEAVE ENGINE RUNNING WhILE UNATTENdEd.
TURN OFF AFTER EVERY USE.
NEVER CARRY POWERhEAd ANd AUGER BETWEEN hOLES WhILE ENGINE IS RUNNING.
800-345-6007 Page 7
GetEarthquake.com
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
WARM ENGINE START
1. Move choke lever to ChOkE position.
note: choke position is defined by moving the choke lever as far to the choke position as possible.
2. Continue with Step 4 of Cold Engine Starting. hot Engine Start:
1. Continue with Step 4 of Cold Engine Starting.
2. If engine does not fire, refer to Step 1 of Warm Engine Starting.
dO NOT attempt to start engine in the following ways:
• dO NOT use starting fluid.
• dO NOT spray flammable liquids or vapors into air cleaner, carburetor or spark plug chamber.
• dO NOT remove spark plug and pull on starter rope. Flammable fuel can spray out & ignite from a spark from spark plug.
Page 8
GetEarthquake.com
800-345-6007
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
MAINTENANCE ANd STORAGE
POWER AUGER MAINTENANCE
1. The gear case has 4 oz. of grease installed at the factory. It is recommended that once a year the gear case be split and the grease level checked. Add grease only if level of grease is below top of the gears. dO NOT OVERFILL.
2. Keep all screws, nuts, and bolts tight.
3. For cold weather operation, store the unit in a cool environment.
Transferring the unit from a warm to a cold place can cause the build up of harmful condensation.
4. If blade performance decreases, turn unit off and disconnect spark plug wire. Carefully inspect cutting edge of blade for any signs of wear. If blades show any of these signs, they need to be sharpened or replaced.
ENGINE MAINTENANCE
Please read the maintenance schedule and observe these recommendations to extend the life of your engine.
Good maintenance is essential for safe, economical, and troublefree operation. It will also help reduce air pollution. To help you properly care for your engine, the following pages include a maintenance schedule, routine inspection procedures, and simple maintenance procedures using basic hand tools. Other service tasks that are more difficult, or require special tools, are best handled by professionals and are normally performed by a technician or other qualified mechanic.
Maintenance, replacement or repair of the emissions control devices and systems may be performed by any non-road engine repair establishment or individuals. However, items must be serviced by an authorized dealer to obtain "no charge" emissions control service.
The maintenance schedule applies to normal operating conditions. If you operate your engine under unusual conditions, such as sustained high-load or high-temperature operation, or use in unusually wet or dusty conditions, consult your servicing dealer for recommendations applicable to your individual needs and use.
MAINTENANCE SChEdULE
MAINTENANCE ITEM
Clean Engine and Check Bolts & Nut
Air Filter Check
(See Air Filter section) Clean *
Replace
Spark Plug (Gap .028”) Check/
Adjust
(See Spark Plug section) Replace
Every 8 hours
(daily)
X
X
Every 0 hours or seasonally Yearly
* Service more frequently under dusty conditions
X
X
X
X
X
CAUTION
TO PREVENT ACCIdENTAL STARTING:
ENGINE MUST BE TURNEd OFF ANd COOL, ANd
SPARk PLUG WIRE MUST BE REMOVEd FROM
SPARk PLUG BEFORE ChECkING ANd AdJUST-
ING ENGINE OR EqUIPMENT.
TEMPERATURE OF MUFFLER ANd NEARBY AR-
EAS MAY ExCEEd 150º F. (65º C). AVOId ThESE
AREAS.
ChECk AUGER OFTEN FOR LOOSE NUTS ANd
BOLTS. kEEP ThESE ITEMS TIGhTENEd.
NEVER STORE ENGINE WITh FUEL IN ThE TANk
INSIdE A BUILdING. POTENTIAL SPARkS MAY
BE PRESENT FOR IGNITION OF FUEL ANd FUEL
VAPORS.
AN AdULT MUST ALWAYS dO MAINTENANCE
ANd REPAIR ON ENGINE ANd AUGER.
ENGINE MUST BE ShUT-OFF, COOL, ANd SPARk
PLUG WIRE REMOVEd BEFORE ANY REPAIR OR
MAINTENANCE CAN BE dONE.
COOLING FINS
Cooling fins, air inlets and linkages must be free from any debris before each use.
AIR FILTER
Never run engine without air cleaner properly installed.
Added wear and engine failure may occur if air cleaner is not installed on engine.
Service air cleaner every 3 months or after 20 hours of operation. Clean filter daily in extremely dusty conditions.
IMPORTANT
NEVER TWIST AIR FILTERS WhEN CLEANING.
ALWAYS PRESS.
STEPS FOR CLEANING RING STYLE FOAM FILTER
- SEE PARTS ExPLOSION ON PAGE 16.
1. Wash in warm water with mild soap until dirt and debris are removed. Press filter when washing, do not twist.
2. Rinse in warm water until soap and dirt are removed.
3. Dry filter by wrapping in a clean cloth and pressing filter until it is dry.
4. Apply oil to the entire filter.
5. Remove excess oil.
6. Attach the filter and air cleaner cover to the engine.
800-345-6007 Page 9
GetEarthquake.com
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
STEPS FOR CLEANING BLOCk STYLE FOAM AIR FILTER
- SEE PARTS ExPLOSION ON PAGE 16.
1. Before removing the air filter cover, move the choke lever to the choke position. (Figure 1)
2. To remove air filter cover, squeeze the latch tabs on both sides of the cover. (Figure )
3. Once the latch tabs are released, remove the air filter cover by rotating the cover away from the engine. (Figure 3)
4. Remove the foam filter element (Figure 4) and replace with a new oiled filter, or clean the original foam filter with warm water and mild soap by following the previous steps for Cleaning Air
Filter. Remember to thoroughly oil the foam filter with 30 or 40 weight motor oil and squeeze out any excess oil.
5. Reinstall the foam filter, pressing it in place to ensure that the foam is fully seated into its sealed position. (Figure 5)
6. Replace the air filter cover so that it fully snaps into place and is secured by the latch tabs. Check that the cover is securely attached by pulling slightly on the cover. If the cover doesn’t move when pulled, it is secure.
Figure 3
Figure 4
Figure 1
Page 10
Figure
GetEarthquake.com
Figure 5
800-345-6007
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
SPARk PLUG
The recommended spark plug is a NGK BM6A which cross references to a Champion CJ8.
1. Check spark plug at the beginning of each season.
2. Disconnect the spark plug cap, and clean any debris from around the spark plug area.
3. Remove spark plug and replace if any of the following occur; pitted electrodes, burned electrodes, cracked porcelain, or deposits around electrodes.
4. After analysis, seat spark plug and tighten with spark plug wrench.
• Reinstall original spark plug, tighten additional 1/2 turn.
• Installing new spark plug, adjust spark plug gap to .028” and tighten additional 1/8 – 1/4 turn .
NOTE: Loose spark plug may overheat and damage engine.
Over tightened spark plug may damage threads in the cylinder head.
CARBURETOR
Never tamper with factory setting of the carburetor.
TRANSPORTING YOUR EARTh AUGER
1. Never transport engine inside an enclosed space or vehicle.
Fuel or fuel vapors may ignite causing serious injury or death.
2. If fuel is present in the fuel tank, transport in an open vehicle in an upright position.
3. If an enclosed vehicle must be used, remove gas into an approved red fuel container. dO NOT siphon by mouth.
4. Run engine to use up the fuel in the carburetor and fuel tank.
Always run engine in a well ventilated area.
5. Wipe away any spilled fuel from engine and earth auger. Allow to dry.
LONG TERM STORAGE
If your earth auger will not be used for more than one month, prepare it for long term storage.
STEPS FOR LONG TERM STORAGE
1. Add fuel stabilizer according to manufacturer’s instructions.
2. Run engine for 10-15 minutes to ensure that the stabilizer reaches the carburetor.
3. Remove the remainder of the fuel from the gas tank into an approved fuel container.
4. Remove auger from powerhead and apply a thin layer of grease to the output shaft (8913).
5. Store auger and powerhead (engine) in a vertical position.
6. Remove all debris from auger and powerhead (engine).
CAUTION
TO AVOId INJURY OR dEATh, NEVER SIPhON FUEL BY
MOUTh.
NEVER STORE EARTh AUGER WITh FUEL IN ThE GAS
TANk INSIdE AN ENCLOSEd AREA OR BUILdING.
TO PREVENT ACCIdENTAL STARTING:
ENGINE MUST BE TURNEd OFF ANd COOL, ANd
SPARk PLUG WIRE MUST BE REMOVEd FROM SPARk
PLUG BEFORE ChECkING ANd AdJUSTING ENGINE
OR EqUIPMENT.
AN AdULT MUST ALWAYS dO MAINTENANCE ANd RE-
PAIR ON ENGINE ANd AUGER.
ENGINE MUST BE ShUT-OFF, COOL, ANd SPARk PLUG
WIRE REMOVEd BEFORE ANY REPAIR OR MAINTE-
NANCE CAN BE dONE.
800-345-6007 Page 11
GetEarthquake.com
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
SERVICE INFORMATION
At Ardisam, we build quality and durability into the design of our products; but no amount of careful design by us, and careful maintenance by you, can guarantee a repair-free life for your machine. Most repairs will be minor, and easily fixed by following the suggestions in the troubleshooting guide in this section.
The guide will help you pinpoint the causes of common problems and identify remedies.
For more complicated repairs, contact your place of purchase or
Ardisam, Inc. for an authorized service center in your area. Ardisam will make the necessary repairs if a service center is not available. A parts catalog is included in this section.
We will always be glad to answer any questions you have, or help you find suitable assistance. To order parts or inquire about warranty, call, write or e-mail us at the address found below, under the section ordering repair parts.
ORdERING REPAIR PARTS
Parts can be obtained from the store where your earth auger was purchased, direct from the manufacturer or online. To order from the manufacturer, call, write or e-mail:
Ardisam, Inc.
1160 Eighth Avenue, Cumberland, Wisconsin 5489
1-800-345-6007 • 1-715-8-415
E-mail: [email protected]
www.getearthquake.com
Please include the following information with your order:
1. Part numbers
2. Part description
3. Quantity
4. Model number and serial number
NOTE: When ordering from the manufacturer, there is a $10.00 minimum order.
CAUTION
PRACTICE SAFETY AT ALL TIMES. ENGINE MUST BE
TURNEd OFF ANd ALLOWEd TO COOL, ANd SPARk
PLUG WIRE MUST BE dISCONNECTEd BEFORE AT-
TEMPTING ANY MAINTENANCE OR REPAIR.
Page 1
GetEarthquake.com
800-345-6007
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
TROUBLEShOOTING
PROBLEM
Engine will not start
POSSIBLE CAUSE
1. Power switch off
2. Spark plug wire disconnected
3. Out of fuel
4. Spark plug wet, faulty or improperly gapped
5. Throttle control not held open
REMEdY/ACTION
1. Flip switch to ON position
2. Connect spark plug wire to spark plug
3. Refuel
4. Clean, replace or gap spark plug
5. Squeeze throttle control when pulling recoil handle
6. Push fuel line down into fuel in gas tank 6. Fuel line hose not positioned in bottom of gas tank
1. Dirty air filter Engine runs rough, floods during operation
1. Clean or replace air filter
Engine is hard to start
Engine misses or lacks power
Engine runs, then quits
Engine revs too high
Auger turns at idle
Auger turns, but has no power
Auger jumps
Auger cuts slowly
2. Choke partially engaged
3. Carburetor out of adjustment
1. Stale fuel
2. Turn off choke
3. Call factory
2. Spark plug wire loose
1. Drain old fuel and replace with fresh.
Use gas stabilizer at end of season
2. Make sure spark wire is securely attached to spark plug
3. Clean carburetor, use gas stabilizer, new gas can 3. Dirty carburetor
4. Throttle control not held open
4. Spark plug wet, faulty or improperly gapped
1. Gas cap not venting
4. Prime unit 3 more times, squeeze throttle when pulling recoil handle
1. Remove and clean 1. Clogged gas tank
2. Clogged air filter 2. Clean or replace
3. Carburetor out of adjustment or bad 3. Call factory
4. Clean, replace or gap spark plug
1. Open manual venting gas cap screw all the way open (counterclockwise)
2. Plugged fuel filter 2. Clean or replace
3. Carburetor out of adjustment or bad 3. Call factory
1. Carburetor out of adjustment
1. Idle speed too high
1. Call factory
1. Adjust idle speed lower
2. Broken clutch spring
1. Choke on
2. Carburetor out of adjustment
3. Broken transmission
4. Worn clutch shoes
5. Worn engine lower seat
1. Blade damaged
1. Dull blade
2. Damaged fishtail point
2. Replace spring
1. Turn off choke after engine is running
2. Call factory
3. Call factory
4. Replace clutch shoes and spring
5. Call factory
1. Replace with new blade
1. Buy new blade, or have blade sharpened at factory
2. Replace fishtail point
Contact service provider if above remedies fail at 800-345-6007.
800-345-6007 Page 13
GetEarthquake.com
E43 POWERhEAd & AUGER PARTS
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
ALTERNATE ASSEMBLY
FOR CLUTCh dRUM &
PINION GEAR
9
35
11
Page 14
25
33
26
32
27
24
23
34
22*
29
28**
30
31
* Includes blade, fishtail point, shock spring, shock top, & hardware.
** Includes mounting hardware.
800-345-6007
GetEarthquake.com
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
E43 POWERhEAd PARTS LIST
kEY
NO.
PART
NO.
dESCRIPTION
1 E43CC2 GAS ENGINE, 43CC
2 1027F HANDLEBAR, FOAMED
3 3004119 TRANSMISSION COMPLETE
4 4809 TRIGGER ASSEMBLY
5 4814
6 4811
BOLT 10-24 X 1-1/4 PHILLIPS
TRUSS HD
THROTTLE CABLE
7 8930B BOLT 1/4-20 X 3/4 HH GR5 BLK
8 3004111 GEAR CASE TOP
9 3004100 CLUTCH DRUM
10 8922 BALL BEARING R12 DOUBLE LIP
1
3
11 9814 1
12 8924
GEAR 7T PINION THREADED,
5/8” THREAD
SNAP RING
1
4
1
2
1
1
1 qTY.
1
1
13
14
15
16
17
8915
8912
8919
8923
9214
18 8939
19 8913
20 8929
DOWEL PIN STEEL 1/4” X 1/2”
GEAR 44T 3/4” HOLE
GASKET
BALL BEARING R10
GEAR 10T/48T ONE-PIECE
CLUSTER
GEAR CASE BOTTOM
SHAFT OUTPUT 7/8”
BOLT 1/4-20 X 1-1/2 SHCS
21 8931F BOLT 1/4-20 X 2 SHCS F-T
ALTERNATE ASSEMBLY
9 3004104 CLUTCH DRUM
11 9814MM GEAR 7T PINION THREADED,
8MM THREAD
35 300409 SPACER
1
2
1
1
1
1
1
1
1
1
2
4
AUGER PARTS & ACCESSORIES LIST
kEY
NO.
PART
NO.
22* EA2F
EA3F
EA4F
EA6F
EA8F
EA10F dESCRIPTION
EARTH AUGER 2”, COMPLETE
EARTH AUGER 3”, COMPLETE
EARTH AUGER 4”, COMPLETE
EARTH AUGER 6”, COMPLETE
EARTH AUGER 8”, COMPLETE
EARTH AUGER 10”, COMPLETE
23 1423 BOLT 5/16-18 X 2 HHCS GR5
24 WF516 WASHER, FLAT 5/16” STANDARD
25 60G56 NUT 5/16-18 BI-WAY LOCK
26 53684
27 8980
28** EB4
EB6
SHOCK TOP 1-PC
SHOCK SPRING
EARTH BLADE, 4”
EARTH BLADE, 6”
EB8
EB10
EARTH BLADE, 8”
EARTH BLADE, 10”
EB6HD HEAVY DUTY EARTH BLADE, 6”
EB8HD HEAVY DUTY EARTH BLADE, 8”
EB10HD HEAVY DUTY EARTH BLADE, 10”
29 EBOLT BOLT 1/4-28 X 5/8 HH GR5
30 ENUT NUT 1/4-28 BI-WAY LOCK
31 8958HD FISHTAIL POINT SHARPENED
8970 POINT, EARTH 2” & 3” AUGERS
32 1433
33 2104
34 143
EXT6
EXT12
EXT18
BOLT 3/8-16 X 1-1/2 HH
NUT 3/8-16 HEX LOCK BI-WAY
SHOCK MECHANISM COMPLETE
(For reference only. Contact customer service for replacement)
DEPTH EXTENSION 6”
DEPTH EXTENSION 12”
DEPTH EXTENSION 18”
* Includes blade, fishtail point, shock spring, shock top, & hardware.
** Includes mounting hardware.
1
1
1
1
1
1
1
1
1
1
1 qTY.
1
1
1
1
1
1
2
2
2
2
1
1
1
2
1
1
1
800-345-6007 Page 15
GetEarthquake.com
E43 ENGINE PARTS
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
Page 16
GetEarthquake.com
800-345-6007
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
E43 ENGINE PARTS LIST
10
11
12
13
5
6
3
4
7
8
9 kEY
NO.
PART NO. dESCRIPTION
1
2
300484
300337
FLYWHEEL, MAGNETO
NUT, FLANGE M8
300462
300413
300412
300449
300450
300467
3004110
WASHER, ROTOR
CLUTCH ROTOR ASSEMBLY
SPRING, CLUTCH
WASHER, SPRING
BOLT, SHOULDER
PIN, LOCATING
MOUNT RING & SHROUD
300491 RECOIL CLUTCH
300429 PLATE, RECOIL
3004121 HANDLE, RECOIL (STANDARD)
300430 RECOIL ASSEMBLY WITH
STANDARD HANDLE
20
21
22
23
24
25
26
16
17
18
19
14 300472 IGNITION COIL
-300472CE IGNITION COIL CE
15 300482 SHROUD, ENGINE
300493 BOLT, STUD M6 X 62MM
300475 GASKET, MUFFLER
4813
4812
MUFFLER
COVER, MUFFLER
BM6A
300483
300476
300478
300479
300486
300481
SPARK PLUG
COVER, ENGINE SHROUD
GASKET, INTAKE
WINDPIPE, INTAKE 43CC/51CC
GASKET, CARBURETOR
CARBURETOR
O-RING, CARBURETOR
27
28
29
30
3004109 PRIMER BULB
300329* BASE, INTAKE
300340* CHOKE LEVER, SIDE MOUNT
300328* CHOKE COVER
31 3004132* SCREW, THROTTLE LEVER
32 300455 PLATE, INTAKE COVER
ADAPTER
33
34
300457
300435
COVER, AIR FILTER
AIR FILTER
35 300330 COVER, INTAKE
*For reference only. Contact customer service for replacement.
qTY.
1
1
1
2
2
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
45
46
47
48
49
50
38
39
40
41 kEY
NO. PART NO. dESCRIPTION
36
37
56105
300331
BRACKET, GAS TANK
GAS TANK
42
43
44
300401
300332
1021
300494
300497
300498
300335
GAS CAP, MANUAL VENTING
SHROUD, GAS TANK
SWITCH, ROCKER
GROMMET, 2-HOLE GAS TANK
HOSE, PRIMER LINE
HOSE, FUEL LINE
BOLT W/WASHER PHILLIPS HH
300492
300471
300439
300336
300438
300456
NUT, FLANGE M6
BOLT W/WASHER M5 X 12MM
BOLT W/WASHER PH M5 X 18MM
BOLT HH M6 X 10MM
BOLT W/WASHER M5 X 25MM
BOLT M5 X 50MM
51
52
--
300338 KEY, FLYWHEEL
--
53 3004103 FILTER, FUEL
54 300351 BOLT HH M6 X 8MM
55 3004158 COVER, AIR FILTER
56 30041501* BASE, AIR FILTER
57 3004156 FOAM, AIR FILTER
58 3004157 PLATE, REINFORCEMENT
59 3004153* BOLT, CHOKE LEVER
60 3004155* WASHER, CHOKE LEVER
61 3004154* NUT, NYLOC, CHOKE LEVER
-
-
62 3004151* CHOKE LEVER
63 3004152* CHOKE PADDLE
300470 FUEL LINE HOSE & FILTER
3004114 KIT, CARBURETOR
* P/N 3004150 Air Filter Base sold as an assembly unit only.
1
1
1
1
2
1
1
1
1
2
--
1
1
1
1
7
2
2
5
2
2 qTY.
1
1
1
1
1
1
1
1
4
800-345-6007 Page 17
GetEarthquake.com
Page 18
e43 earth auger powerhead
Warranty Terms and Conditions
PROdUCT WARRANTY: 1-YEAR LIMITEd WARRANTY
Ardisam, Inc., a manufacturing company, warrants this EARThqUAkE® EARTh AUGER POWERhEAd to be free from defects in the material or workmanship for a period of one year from the date of purchase. During the one-year warranty of this product, Ardisam will furnish, at their discretion, parts and labor to correct any defect caused by faulty material or workmanship. Any unit used in a commercial application is covered for a period of 90 days after purchase.
This warranty applies to the original owner with a proof of purchase and is not transferable. This guarantee is void unless the warranty card is properly filled out and received by Ardisam, Inc., within 30 days of purchase or go to www.
GetEarthquake.com for online registration.
For replacement parts, phone 800-345-6007 or go online to www.GetEarthquake.com.
ENGINE WARRANTY: -YEAR LIMITEd WARRANTY
Ardisam, Inc., a manufacturing company warrants its Viper Engines under a two-year limited warranty to be free from defects in materials and workmanship for the service life of the product not to exceed twenty four consecutive months from the date of purchase for consumer applications. As an Ardisam Viper small engine owner, you are responsible for executing proper maintenance listed in your Operating and Maintenance Instructions. The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated above.
*These warranties apply only to products which have not been subjected to negligent use, misuse, alteration, accident, unauthorized parts, failure to use proper fuel and oil, or if repairs have been performed at non-authorized service centers.
These warranties supersede all other warranties either expressed or implied and all other obligations or liabilities on our part. Ardisam, does not assume, and does not authorize any other person to assume for us, any liability in connection with the sale of our products. To be at "No Charge," warranty work must be sent directly to Ardisam, Inc. or one of our authorized service centers and performed by them. To obtain warranty service and/or replacement instructions, contact our customer service department at 800-345-6007 Monday through Friday from 8 a.m. to 5 p.m. or visit www.ardisam.
com. If you choose to ship your product to Ardisam for warranty repair, you must first have prior approval from Ardisam by calling our customer service department at 800-345-6007 for a return material authorization number (RMA#). Under these circumstances, all items must be shipped prepaid. Ardisam will at no charge, repair or replace, at their discretion, any defective part which falls under the conditions stated above. Ardisam retains the right to change models, specifications and price without notice.
EARTHQUAKE
A Division of Ardisam, Inc.
1160 Eighth Avenue; P.O. Box 666
Cumberland, Wisconsin 54829
1-800-345-6007 · Fax (715) 822-4180
E-mail: [email protected]
Explanation of Emissions Control
Warranty Provisions
Viper Engines are designed, built and equipped to meet all EPA requirements. It warrants that it is free from defects in material and workmanship that could cause failure to the warranted part; and that it is identical in all material respects to the engine described in the manufacturer's application for certification. When a warrantable condition exists, Viper will repair your engine at no cost to you, including parts and labor. The engine emissions label will indicate certification information. If the purchaser is in need of a warrantable repair and is not within 100 miles distance from an Ardisam authorized repair center, Ardisam will pay for shipping costs to and from an authorized
Ardisam repair center.
Listed below are the parts covered by the emissions control systems warranty. Some parts listed below may require scheduled maintenance and are warranted up to the first scheduled replacement point for that part.
Coverage under this warranty includes only the parts listed below (the emission and evaporation control systems) if so equipped:
• Air Filter Assembly (only to the first scheduled replacement point)
• Fuel Filter (only to the first scheduled replacement point)
• Carburetor
• Fuel Lines, Fuel Line Fittings and Clamps
• Fuel Metering Valve (if equipped)
• Evaporative System (if equipped)
- Canister (if equipped)
- Canister filter (if equipped)
- Vapor hose (if equipped)
- Orifice connector (if equipped)
-Fuel tank
-Fuel cap
-Primer bulb canister (if equipped)
• Spark Plugs
• Magneto Ignition System
• Muffler Assembly
LIMITATIONS
T he Emission Control Systems Warranty shall not cover any of the following: a) Repair or replacement required because of misuse or neglect, improper maintenance, repairs improperly performed or replacements not conforming to Ardisam, Inc., specifications that adversely affect performance and/or durability and alterations or modifications not recommended or approved in writing by Ardisam, Inc.
b) Replacement of parts and other services and adjustments necessary for required maintenance at or after the first scheduled replacement point; c) Consequential damages such as loss of time, inconvenience, loss of use of the engine or equipment, etc.
d) Diagnosis and inspection fees that do not result in eligible warranty service being performed; and e) Any add-on or modified part, or malfunction of authorized parts due to the use of add-on or modified parts.
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
These items will be covered for a period of two years from the date of the original purchase. Viper warrants that: the components are designed, built and equipped so as to conform with all applicable regulations adopted by the EPA; that they are free from defects in material and workmanship that could cause failure to the engine or other; and that the components used are identical in all material respects to the engine described in the manufacturer's application for certification. The warranty period begins on the date the engine is originally purchased.
MAINTENANCE ANd REPAIR REqUIREMENTS
The owner is responsible for the proper use and maintenance of the engine. Ardisam, Inc. recommends that all receipts and records covering the performance of regular maintenance be retained in case questions arise. If the engine is resold during the warranty period, the maintenance records should be transferred to each subsequent owner. Ardisam, Inc. reserves the right to deny warranty coverage if the engine has not been properly maintained; however, Ardisam, Inc. may not deny warranty repairs solely because of the lack of repair maintenance or failure to keep maintenance records.
Normal maintenance replacement or repair of emission control devices and systems may be performed by any repair establishment or individuals; however, warranty repairs must be performed by an Ardisam authorized service center. Any replacement parts or service that is equivalent in performance and durability may be used in non-warranty maintenance or repairs, and shall not reduce the warranty obligations of the engine manufacturer.
The warranty on emissions-related parts is as follows:
• Any warranted part that is not scheduled for replacement as required maintenance in the owner's manual supplied, is warranted for the warranty period stated above. If any such part fails during the period of warranty coverage, that part will be repaired or replaced at no charge to the owner. Any such part repaired or replaced under the warranty will be warranted for the remaining warranty period.
• Any warranted part that is scheduled only for regular inspection in the owner's manual supplied, is warranted for the warranty period. Any such part repaired or replaced under warranty will be warranted for the remaining warranty period.
• Any warranted part that is scheduled for replacement as required maintenance in the owner's manual supplied, is warranted for the period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first scheduled replacement, the part will be repaired or replaced at no charge to the owner. Any such part repaired or replaced under warranty will be warranted for the remainder of the period prior to the first scheduled replacement point for the part.
• Add on or modified parts that are not exempted by the Air
Resources Board may not be used. The use of any nonexempted add on or modified parts by the owner will be grounds for disallowing a warranty claim. The manufacturer will not be liable to warrant failures of warranted parts caused by the use of a nonexempted add on or modified part.
800-345-6007 Page 19
GetEarthquake.com
Page 0
Page 1
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
NOTES
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
Page 800-345-6007
GetEarthquake.com
ASSEMBLY INSTRUCTIONS ANd PARTS ExPLOSIONS
E43 Model
NOTES
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
_____________________________________________________________________________________________
800-345-6007 Page 3
GetEarthquake.com
Visit www.ardisam.com
and discover more innovations that will benefit you throughout the year.
Earthquake, Division of Ardisam, Inc.
1160 Eighth Avenue; P.O. Box 666
Cumberland, Wisconsin 54829
800-345-6007 · Fax (715) 822-4180
E-mail: [email protected]
GetEarthquake.com

Public link updated
The public link to your chat has been updated.
Advertisement