SDC15 Single Loop Controller User`s Manual for

SDC15 Single Loop Controller User`s Manual for
WARNING
Note that incorrect wiring of the SDC15 can damage the SDC15
and lead to other hazards. Check that the SDC15 has been
correctly wired before turning the power ON.
Before wiring, or removing/mounting the SDC15, be sure to turn
the power OFF. Failure to do so might cause electric shock or
faulty operation.
Do not touch electrically charged parts such as the power
terminals. Doing so might cause electric shock.
Do not disassemble the SDC15.
Doing so might cause electric shock or faulty operation.
SDC15
Single Loop Controller
User's Manual
for Installation
REQUEST
Ensure that this User's Manual is handed over to the user before the
product is used.
Copying or duplicating this User's Manual in part or in whole is forbidden.
The information and specifications in this User's Manual are subject to
change without notice.
Considerable effort has been made to ensure that this User's Manual is
free from inaccuracies and omissions.
If you should find any inaccuracies or omissions, please contact
Yamatake Corporation.
In no event is Yamatake Corporation liable to anyone for any indirect,
special or consequential damages as a result of using this product.
2003 Yamatake Corporation ALL RIGHTS RESERVED
■ External Dimensions
● C15T (Panel Mount Type)
(unit: mm)
Cautions are indicated when mishandling
this product might result in minor injury to
the user, or only physical damage to this
product.
2
48
60
Mounting bracket
(Accesory)
Terminal screw
M3
SDC15
pv
48
CAUTION
■ Mounting Procedure
· The mounting must be horizontal within 10 degrees tilted in back side
lowering or within 10 degrees tilted in back side rising.
· In the case of panel mount type (C15T), the mounting panel should be
used with a thickness of less than 9 mm of firm board.
sp
59
injury to the user.
■ Location
Install the controller in the following locations:
· Common mode voltages for I/O excluding the power supply and relay
contact output: The voltage to ground is 33Vr.m.s max., 46.7V peak
max., and 70Vdc max.
· Not high or low temperature / humidity.
· Free from sulfide gas or corrosive gas.
· Less dust or soot.
· Appropriately processed locations to prevent direct sunlight, wind or rain.
· Less mechanical vibration and shock.
· Not close to the high voltage line, welding machine or electrical noise
generating source.
· The minimum 15 meters away from the high voltage ignition device for a
boiler.
· Less effect by the magnetic.
· No flammable liquid or gas.
mode
rdy
man
ev1
ev2
ev3
ot1
ot2
para
1
● Connection of C15T
Control outputs
Relay
1
2
3
Voltage pulse
1
2
51
SDC15
pv
8
7
6
2- M4
Mounting hole
sp
ev1
ev2
ev3
ot1
Current transformer inputs
CT2
+
–
Event outputs
7
8
9
10
ot2
Voltage pulse
40
9
Stopper
Socket
10
Current
3
11
1
Insert the stoppers at the top and bottom of
the socket into the holes of the controller
body to firmly secure it to the socket.
Voltage pulse
● Panel Cutout Dimensions
30 min.
1
2
3
+
1–
2+
+
–
Gang-mounting
(unit: mm)
45 +0.5
0
45 +0.5
0
(48xN -3) +0.5
0
1
2
3
Current
45 +0.5
0
Current
1
13
7
2
14
8
3
15
9
4
16
10
5
17
11
6
18
12
1
Relay
2
3
7
8
9
10
1
Power supply
11
11
Handling Precautions
• When three or more units are gang-mounted horizontally, the
maximum allowable ambient temperature is 40°C.
• If dustproof or waterproof protection is required, mount the device
using the stand-alone mounting method. If gang-mounted,
dustproof and waterproof protection may not be maintained.
• Provide a space of at least 50mm or more above and below
the controller.
Wiring
Be sure to provide a switch within operator reach for shutting OFF the main
power supply to the controller in the main supply wiring.
Also, in case of AC power supply models, the main supply wiring also requires
a time-lagged type (T) fuse (rated current: 0.2A, rated voltage: 250 V).
(IEC127)
The following table shows the meaning of the symbols in the terminal wiring
label on the controller side:
Meaning
DC power supply
AC power supply
Caution, fear of electric shock
Caution
Handling Precautions
• Before wiring the SDC15, verify the controller's model No. and
terminal Nos. written on the label on the side of the body.
Inspect all wiring once wiring work for the SCD15 has been
completed.
• Use M3 crimp-type terminal lugs for wiring to terminal.
• Provide a distance of at least 50cm between I/O lead wires or
communications lead wires and power lead wires of 100V min.
Also, do not pass these lead wires through the same piping or
wiring duct.
• Be careful not to allow any crimp-type terminal lugs to touch
adjacent terminals.
• Prepare a heater current conductor to send a heater current
through the current transformer.
Do not use a heater current that exceeds the specified
permissible current as this may damage the controller.
• The controller requires about 6 seconds to start up once the
power is turned ON. The controller can be used once it has
started up. However, it is recommended to allow a warm-up
time of at least 30 minutes to attain the specified accuracy.
• The current transformer input cannot be used for phase
control.
• There is no isolation provided between control output 1 and
control output 2.
Install an isolator as required.
• Do not connect a terminating resistor to either end of the RS485 communications line.
Doing so may interfere with communication.
C
DI/COM
2
4
5
6
B
RTD
A
+
Current
mA
–
Voltage
V
+
DC power supply
24Vac/24 to 48Vdc
(nonpolar)
12
4
5
6
+
AC power supply
100 to 240Vac
12
+
1–
2+
–
Thermocouple
Relay
(independent
contact)
2
PV inputs
(N: number of mounted units)
Symbols
+
1–
2+
1
2
Current
Stand-alone mounting
1
2
3
2
Voltage pulse
13
14
15
CT1
4
71
man
5
para
Mounting
44.8
Warnings are indicated when mishandling
WARNING this product might result in death or serious
Terminal screw
M3.5
50 min.
This product has been designed, developed and manufactured for
general-purpose application in machinery and equipment.
Accordingly, when used in applications outlined below, special care
should be taken to implement a fail-safe and/or redundant design
concept as well as a periodic maintenance program.
• Safety devices for plant worker protection
• Start/stop control devices for transportation and material
handling machines
• Aeronautical/aerospace machines
• Control devices for nuclear reactors
Never use this product in applications where human safety may be
put at risk.
SAFETY PRECAUTIONS
Socket 81446391-001
(sold separately)
31
26.5
48
rdy
Use the SDC15 within the operating ranges recommended in the
specifications (temperature, humidity, voltage, vibration, shock,
mounting direction, atmosphere, etc.).
Failure to do so might cause fire or faulty operation.
Do not block ventilation holes.
Doing so might cause fire or faulty operation.
Wire the SDC15 properly according to predetermined standards.
Also wire the SDC15 using specified power leads according to
recognized installation methods.
Failure to do so might cause electric shock, fire or faulty operation.
Do not allow lead clippings, chips or water to enter the controller case.
Doing so might cause fire or faulty operation.
Firmly tighten the terminal screws at the torque listed in the
specifications. Insufficient tightening of terminal screws might
cause electric shock or fire.
Do not use unused terminals on the SDC15 as relay terminals.
Doing so might cause electric shock, fire or faulty operation.
We recommend attaching the terminal cover (sold separately)
after wiring the SDC15.
Failure to do so might cause electric shock.
Use the relays within the recommended service life.
Continuous use might cause fire or faulty operation.
Use Yamatake Corporation's "SURGENON" if there is the risk of
power surges caused by lightning.
Doing so might cause fire or faulty operation.
Do not operate the keys with a mechanical pencil or sharp-tipped
object. Doing so might cause faulty operation.
• Regarding a device or equipment which is connected to this
controller, use a model to which the basic insulation meeting
with the power supply voltage and the maximum operating
voltage of the I/O units is provided.
(unit: mm)
74.2
61.2
mode
CAUTION
RESTRICTIONS ON USE
■ Unpacking
Check the following items when removing the SDC15 from its package:
Name
Part No.
Q'ty
Remarks
Mounting Bracket
81446403-001
1
For C15T only
Gasket
81409657-001
1
For C15T only
User's Manual
CP-UM-5287E
1
This Manual
CP-UM-5287
1
● C15S (Socket Mount Type)
48
Thank you for purchasing the SDC15.
Before operating this product described in this User's Manual, please
take note of the following points regarding safety.
Be sure to keep this manual nearby for handy reference.
This manual explains handling precautions, mounting, wiring procedures,
PV range types, parameter list and main specifications only. See the
user's manuals listed below for detailed handling procedures, setting
methods, etc. These manuals also contain information on using various
functions.
SDC15 Single Loop Controller User's Manual for Basic Operation
CP-SP-1147E
SDC15 Single Loop Controller User's Manual for Installation &
Configuration CP-SP-1148E
SLP-C35 Smart Loader Package for SDC15/25/26/35/36 Single Loop
Controller User's Manual CP-UM-5290E
Handling Precautions
To fasten this controller onto the panel, tighten a mounting
bracket screws, and turn one more half turn when there is no
play between the bracket and panel. Excessively tightening the
screws may deform the controller case.
3.4
CP-UM-5287E
1
DA
DB
SG
4
5
6
16
17
18
Digital
inputs
16
17
18
RS-485
Communication
● Connection of C15S
Control outputs
Event outputs
5
6
7
8
9
Relay
4
Voltage pulse
5
–
4
+
5
–
4
4
+
3
6
5
Current
6
7
8
9
7
8
mA
Voltage
V
+
C
B
RTD
A
Thermocouple
–
+
2
Relay
(independent
contact)
Power supply
10
8
7
6
3
2
1
3
2
1
1
11
PV inputs
3
2
1
2
10
1
+
Relay
1
9
2
Current
3
5
4
11
10
11
9
10 11
AC power supply
100 to 240Vac
DC power supply
24Vac/24 to 48Vdc
(nonpolar)
3
1
2
Socket terminal No.
● I/O isolation
Items surrounded by solid lines are insulated from other signals.
Power supply
PV input
Current Transfomer input 1
Current Transfomer input 2
Loader communication
Digital input 1
Digital input 2
RS-485 Communication
Control output 1
Control output 2
Internal Event output 1 (Note)
Circuit Event output 2 (Note)
Event output 3
Availability of input or output is based on a model number.
(Note) In case of the independent contact, the part between the event
output 1 and the event output 2 is isolated.
● SP setup
Part names and functions
<
pv
(1)
sp
(4)
(2)
mode
rdy
man
ev1
ev2
ev3
ot1
(3)
ot2
para
(5)
(6)
<
While the PV/SP is displayed in the operation display mode, press the
[<] • [ ] • [ ] key to change the SP in the lower display.
>> When no keys are pressed for 2 sec. or longer, the flashing of the
numeric value is stopped to set the currently displayed value.
SP can be set in the parameter setting display mode.
For details on handling and setting procedures other than the PV input range
setting procedure, refer to the table of parameter list. For the details on
operation and setting method, refer to the following user’s manuals:
SDC15 Single Loop Controller User's Manual for Basic Operation
CP-SP-1147E
SDC15 Single Loop Controller User's Manual for Installation &
Configuration CP-SP-1148E
<
<
Key Operation and Setting
Display when the power
is turned ON.
The mode indicators are lit
sequentially from the left during a
period of 6 sec. after the power has
been turned ON while both the upper
display and lower display are off.
The mode indicator When all mode indicators have been
lit, the display is changed to the
is lit sequentially
operation display.
from the left.
Off.
rdy
man
ev1
ev2
ev3
ot1
ot2
para
No key operation for
No key operation for
3 minutes or more.
3 minutes or more.
Press the [mode] key.
Keep
the
[para]
Press the [mode] key pressed for
Keep the [para] key pressed
key.
2 sec. or longer. for 2 sec. or longer.
Parameter setup
Setup setting display
display
Keep the [para]
key pressed for
2 sec. or longer.
Operation display
pv
pv
pv
sp
sp
sp
mode
mode
PV/SP display
AUTO/MANUAL
selection
PV range type
setup
Press the [para] key.
Press the [para] key.
Press the [para] key.
pv
pv
pv
sp
sp
sp
mode
mode
RUN/READY
selection
Temperature unit
setup
Press the [para] key.
Press the [para] key.
Press the [para] key.
Other setup
(Operate the [para] key
repeatedly.)
Press the [para] key.
Press the [para] key.
C01 No. Sensor type
41
Pt100
42
JPt100
43
Pt100
44
JPt100
45
Pt100
46
JPt100
51
Pt100
52
JPt100
53
Pt100
54
JPt100
63
Pt100
64
JPt100
67
Pt100
68
JPt100
C01 No.
84
86
87
88
89
90
Range[°C]
-200 to +500
-200 to +500
-200 to +200
-200 to +200
-100 to +300
-100 to +300
-50.0 to +200.0
-50.0 to +200.0
-50.0 to +100.0
-50.0 to +100.0
0.0 to 200.0
0.0 to 200.0
0 to 500
0 to 500
Other setup
(Operate the [para] key
repeatedly.)
Press the [para] key.
The display and setup status shown above are examples for
explanation. Therefore, some displays or settings are not
shown actually according to the model and/or setup contents.
Alarm
Error
code
AL01 PV input error
(over range)
AL02 PV input error
(under range)
AL03 CJ failure
Input type
0 to 1V
1 to 5V
0 to 5V
0 to 10V
0 to 20mA
4 to 20mA
A/D conversion error
Parameter error
AL96
Adjustment data error
AL97
Parameter error
(RAM area)
Adjustment data error
(RAM area)
ROM error
AL98
<
<
In the setup setting display mode [C01], press the [<] • [ ] • [ ] key
to set the lower display to select a desired PV range type.
>> When no keys are pressed for 2 sec. or longer, the flashing of the
numeric value is stopped to set the currently displayed value.
Cause
Sensor line break, incorrect wiring,
incorrect range code setting
Sensor line break, incorrect wiring,
incorrect range code setting
Terminal temperature
compensation unit failure
(thermocouple)
PV input error
Sensor line break, incorrect
wiring (RTD)
CT input failure
A current exceeding the upper
(over-range)
limit of the display range was
(CT input 1 or 2,or both) measured. The number of CT
turns or the number of CT
power wire loops is incorrectly
set, or wiring is incorrect.
AL70
AL95
AL99
● PV Input range setup
Power
supply
Optional Additional
functions processing
Defective A/D converter
• Power turned OFF during
fixing of data
• Data corrupted due to noise, etc.
• Power turned OFF during
fixing of data
• Data corrupted due to noise, etc.
Data corrupted due to noise, etc.
Allowable measured current:
Specifications
T
Panel mount type
S
Socket mount type
(Note 2)
Display range lower limit:
Display range upper limit:
Control output 1
Control output 2
R0
Relay contact output
None
V0
Voltage pulse output
None
(for SSR drive)
(Note 1)
Voltage pulse output
VC
Current output
(for SSR drive)
(Note 1)
Voltage pulse output Voltage pulse output
VV
(for SSR drive)
C0
Current output
None
CC
Current output
Current output
Range[°F]
-300 to +900
-300 to +900
-300 to +400
-300 to +400
-150 to +500
-150 to +500
-50 to +400
-50 to +400
-50 to +200
-50 to +200
0 to 400
0 to 400
0 to 900
0 to 900
Thermocouple input
(K, J, E, T, R, S, B, N, PLII, WRe5-26,
DINU, DINL)
R
RTD input (Pt100/JPt 100)
L
DC voltage /DC current input (0 to
1Vdc, 1 to 5Vdc, 0 to 5Vdc, 0 to 10Vdc,
0 to 20mAdc, 4 to 20mAdc)
A
AC Model (100 to 240Vac)
D
(Note 1, 3)
DC Model (24Vac, 24 to 48Vdc)
00
None
01
Event relay output: 3 points
02
Event relay output: 3 points
Current transformer input: 2 points
Digital input: 2 points
(Note 1, 3)
03
Event relay output: 3 points
Current transformer input: 2 points
RS-485 communication
Range
The scaling and
decimal point position
can be changed
variably in a range of
–1999 to +9999
(Note 5)
04
Event relay output: 2 points
(independent contact)
(Note 1, 3, 5)
05
Event relay output: 2 points
(independent contact)
Current transformer input: 2 points
(independent contact)
Digital input: 2 points
Alarm code table
AL11
mode
MV display
Other display and setup
(Operate the [para] key
repeatedly.)
Range[°C]
Range[°F]
-200 to +1200 -300 to +2200
0 to 1200
0 to 2200
0 to 800
0 to 1500
0 to 600
0 to 1100
0 to 400
0 to 700
-200 to +400 -300 to +700
0 to 800
0 to 1500
0 to 600
0 to 1100
-200 to +400 -300 to +700
0 to 600
0 to 1100
-200 to +400 -300 to +700
0 to 1600
0 to 3000
0 to 1600
0 to 3000
0 to 1800
0 to 3300
0 to 1300
0 to 2300
0 to 1300
0 to 2300
0 to 1400
0 to 2400
0 to 2300
0 to 4200
-200 to +400 -300 to +700
-100 to +800 -150 to +1500
This table shows a list of malfunction alarms and countermeasures to take in each case.
mode
(Note 4)
(Note 1)
Handling Precautions
· The accuracy of the B thermocouple is ±5%FS for a range of
260°C or less, and ±1%FS for 260 to 800°C. The indicated low
limit is 20°C.
· The accuracy of the PLII thermocouple(CO1 No.19) in the
range of 0 to 32˚F does not meet the indication accuracy
specified in the Specifications.
· For ranges with a decimal point, tenths are displayed on the
line underneath point.
· Set by the number of setup C01 according to the type and
range of the sensor used.
Off.
mode
PV
input
T
C01 No. Sensor type
1
K
2
K
3
K
4
K
5
K
6
K
9
J
10
J
11
J
13
E
14
T
15
R
16
S
17
B
18
N
19
PLII
20 WRe5-26
21 WRe5-26
24
DIN U
25
DIN L
pv
sp
Control
output
C15
PV range table
(1) Upper display
The following shows the flow of the key operation. Various displays and
settings can be called up to the console:
Basic
Mounting
model No.
(for SSR drive)
(7)
: Displays PV values (current temperature, etc.)
or setup items.
(2) Lower display
: Displays SP values (set temperature, etc.) and
other values of setup items.
(3) Mode indicator rdy
: Lights when READY (control stop)
man
: Lights when MANUAL (manual mode)
ev1 to ev3 : Lights when event relays are ON.
ot1 to ot2 : Lights when the control output is ON.
(4) Mode key
: The operation which was set beforehand can
be done by pressing the key for 1s or more.
Factory setting is RUN / READY selection.
(5) Para key
: Switches the display.
(6) <, , keys
: Used for incrementing numeric values and
performing arithmetic shift operations.
(7) Loader connector: Connects to a personal computer with the special cable
provided in the smart loader package.
Model selection table
Countermeasure
Checking wiring or
reset range code..
Checking the allowable
ambient temperature.
Checking wiring.
• Use a CT with the correct
number of turns for the
display range.
• Reset the number of CT turns.
• Reset the number of CT
power wire loops.
• Check the wiring.
Replace unit.
Reset data or replace unit.
Data corrupted due to noise, etc.
Data corrupted due to noise, etc. Replace unit.
Maintenance
Cleaning:
When wiping out the SDC15, use the soft and dried cloth.
Parts replacement: Do not replace the parts.
Fuse replacement: When replacing the fuse for the power supply wires, make
sure that the replacement fuse complies with all applicable
safety standards.
Standard IEC127, Cutoff Speed Delayed operation type (T),
Rated Voltage 250V, Rated Current 200mA
2
(Note 1, 3, 5)
06
Event relay output: 2 points
(independent contact)
Current transformer input: 2 points
RS-485 communication
Note 1.
Note 2.
Note 3.
Note 4.
Note 5.
Can not be selected for the C15S.
Only 1a contact applicable for the C15S
Current transformer sold separately
Socket sold separately
Can not be selected for the DC model.
00
No additional processing
D0
Inspection Certificate provided
Y0
Complying with the traceability certification
Specifications
● PV Input
Thermocouple:
K,J,E,T,R,S,B,N (JIS C1602-1995)
PL II (Engelhard Industries Data (ITS90))
WRe5-26 (ASTM E988-96(Reapproved
2002))
DIN U,DIN L (DIN 43710-1985)
Resistance temperature detector (RTD):
Pt100 (JIS C1604-1997)
JPt100 (JIS C1604-1989)
DC voltage:
0 to 1V, 1 to 5V, 0 to 5V, 0 to 10V
DC current:
0 to 20mA, 4 to 20mA
Sampling cycle:
500ms
Accuracy :
±0.5%FS±1digit,
±1%FS±1digit for a negative area of the
thermocouple (at ambient temperature
23±2°C)
● Digital input
Input type :
Dry contact or open collector
Allowable ON contact resistance : Max.250Ω
Allowable OFF contact resistance : Min.100kΩ
Allowable ON voltage :
Max.1.0V
Terminal current (ON ) :
Approx.7.5mA in case of short circuit
Approx.5.0mA in case of contact resistance
250Ω
Minimum hold time :
1s or more
● Current transformer input
Number of input points:
2 points
Input object:
Current transformer with 100 to 4,000 turns
(availability is by 100-turn units)
Optional unit Model No.: QN206A
(800 turns, hole diameter: 5.8 mm)
Optional unit Model No.: QN212A
(800 turns, hole diameter: 12mm)
Current measurement
lower limit:
0.4Aac (800 turns, 1 time)
Formula; Number of turns ÷ (2000 x number
of power wire loops)
Current measurement
upper limit:
50.0Aac (800 turns, 1 time)
Display accuracy:
Display resolution:
● Control Output
• Relay output
Contact rating :
Formula; Number of turns ÷ (16 x number of
power wire loops)
70.0Aac (800 turns, 1 time)
Formula; Number of turns ÷ (16 x number of
power wire loops) x 1.4
0.0Aac
70.0Aac (800 turns, 1 time)
Formula; Number of turns ÷ (16 x number of
power wire loops) x 1.4
±5%FS
0.1Aac
NO side 250Vac/30Vdc, 3A (resistive load)
NC side 250Vac/30Vdc, 1A (resistive load)
Life :
NO side Min. 50,000 operations
NC side Min. 100,000 operations
Min. switching specifications : 5V, 100mA
Min. ON time / OFF time :
250ms
• Voltage pulse output (for SSR drive)
Open circuit voltage :
19Vdc±15%
Internal resistance :
82Ω±0.5%
Allowable current :
Max. 24mAdc
Min. OFF time / ON time :
1ms (Time proportional cycle time < 10s)
250ms (Time proportional cycle time ≥ 10s)
• Current output
Output type :
0 to 20mAdc or 4 to 20mAdc current output
Allowable load resistance :
Max.600Ω
Output accuracy :
±0.5%FS (at ambient temperature 23±2°C)
±1%FS at 0 to 1mA
● Event relay outputs (ev1 to 3)
Contact rating :
250Vac/30Vdc 2A (resistive load)
Life :
Min. 100,000 operations
Min. switching specification : 5V, 10mA (Reference value)
● RS-485 communication
Transmission line :
3-wire system
Transmission speed :
4800, 9600, 19200, 38400bps
Communication protocol :
CPL and MODBUS conforming
Terminating resistor :
Do not connect a terminating resistor.
● Environmental condition
• Operating conditions
Ambient temperature :
0 to 50°C (Gang-mounting: 0 to 40°C)
Ambient humidity :
10 to 90%RH (non-condensing)
Power supply voltage :
AC Model
85 to 264Vac, 50/60Hz±2Hz
(Rated power voltage 100 to 240Vac 50/60Hz)
DC Model
21.6 to 26.4Vac, 50/60Hz±2Hz
21.6 to 52.8Vdc
(Rated power voltage 24Vac 50/60Hz,
24 to 48 Vdc)
• Transport conditions
Ambient temperature :
–20 to +70°C
Ambient humidity :
10 to 95%RH (non-condensing)
● Other specifications
Degrees of protection :
Case front side IP66 /NEMA 4 equivalent
(Only for stand-alone mounting on a panel
when an attached gasket is used. )
Power consumption :
AC Model
Max. 12VA (100Vac:8VA, 264Vac:12VA)
(6VA for 100Vac and 9VA for 264Vac to
our company SDC10 equivalent function)
DC Model
Max. 7VA (24Vac)
Max. 5W (24 to 48Vdc)
Non-detected power failure time : Max. 20ms (AC model)
No power failure allowed (DC model)
Altitude :
Max. 2000m
Mass :
Approx.150g (with mounting bracket) at
panel mount type
Approx.200g (with socket) at socket mount
type
Terminal screw tightening torque : 0.4 to 0.6N·m
Applicable standards :
EN61010-1, EN61326
Over-voltage category :
Category II (IEC60364-4-443, IEC60664-1)
Allowable pollution degree :
Pollution degree 2
Accessories and optional parts
Name
Mounting bracket (for C15T)
Gasket
Current transformer
Socket (for C15S)
Hard cover
Soft cover
Terminal cover
Model No.
81446403-001 (Accessory)
81409657-001 (Accessory)
QN206A (5.8mm hole dia.)
QN212A (12mm hole dia.)
81446391-001
81446442-001
81446443-001
81446898-001
User level details
0: Display in basic / standard / high function,
1: Display in standard / high function,
2: Display in high function.
Initial value may vary depending on model No.
SDC15 List of Parameters
[List of Operation Displays]
■ Operation Displays
Display
Upper display: PV
Lower display: SP
LSP 1
Lower display:
LSP
Out
HEAt
COOL
Upper display: PV
At 1 (display
example)
Ct 1
Ct2
E1
E 1. Sb
t 1. --
E2
E2. Sb
t2. --
E3
E3. Sb
t3. --
Item
SP (Target value)
Display
Contents
SP low limit (C07) to SP high limit (C08)
LSP No. (1st digit: 1 to LSP system group (C30 Max. 4)
Value at the
right end digit)
MV (Manipulated –10.0 to +110.0%
Variable)
Setting is disabled in AUTO mode.
(Numeric value does not flash.)
Setting is enabled in MANUAL mode.
(Numeric value flashes.)
Heat MV
Setting is disabled
(Manipulated
–10.0 to +110.0%
Variable)
Cool MV
(Manipulated
Variable)
AT progress
Setting is disabled.
display (1st digit
Except for 0: During execution of AT
= Numeric value
(Value is decreased.)
at right end digit)
0: Completion of AT
CT (Current
Setting is disabled.
transformer)
current value 1
CT (Current
Setting is disabled.
transformer)
current value 2
Internal event 1
Setting range is different depending on the internal
main setting
event operation type.
Internal event 1
–1999 to +9999U: Except below.
sub-setting
0 to 9999U: When the setting value is an absolute value.
–199.9 to +999.9%: For MV.
Timer remaining
Setting is disabled.
time 1
Upper display: The distinction by ON delay or OFF
delay is displayed at the side location of [t1.].
Lower display: Displayed by the unit (either one of
0.1s, s, or min) based on the internal event 1 delay
time unit (E1. the 3rd digit of C3).
Internal event 2
Setting range is different depending on the internal
main setting
event operation type.
Internal event 2
–1999 to +9999U: Except below.
sub-setting
0 to 9999U: When the setting value is an absolute
value.
–199.9 to +999.9%: For MV.
Timer remaining
Setting is disabled.
time 2
Upper display: The distinction by ON delay or OFF
delay is displayed at the side location of [t2.].
Lower display: Displayed by the unit (either one of
0.1s, s, or min) based on the internal event 2 delay
time unit (E2. the 3rd digit of C3).
Internal event 3
Setting range is different depending on the internal
main setting
event operation type.
Internal event 3
–1999 to +9999U: Except below.
sub-setting
0 to 9999U: When the setting value is an absolute value.
–199.9 to +999.9%: For MV.
Timer remaining
Setting is disabled.
time 3
Upper display: The distinction by ON delay or OFF
delay is displayed at the side location of [t3.].
Lower display: Displayed by the unit (either one of
0.1s, s, or min) based on the internal event 3 delay
time unit(E3. the 3rd digit of C3).
Initial
value
0
User
level
0
1
0
-
0
-
0
-
0
-
0
-
0
-
0
0
0
0
-
0
A--M
r--r
At
do Lt
C. dI 1
Item
AUTO/MANUAL
mode selection
RUN/READY
mode selection
AT Stop/Start
selection
Release all DO
latches
Communication
DI 1
Contents
AUTO : AUTO mode
MAN : MANUAL mode
RUN : RUN mode
RDY : READY mode
At. OF : AT Stop
At. ON : AT Start
Lt. ON : Latch continue
Lt. OF : Latch release
dI. OF : OFF
dI. On : ON
0
0
SP- 1 to
SP-4
Item
Contents
SP of LSP1 group to SP low limit (C07) to SP high limit (C08)
LSP4 group
I- 1
Integration time
d- 1
Derivative time
0 to 9999s
(0: No integral control action)
0 to 9999s
(0: No derivative control action)
–10.0 to +110.0%
–10.0 to +110.0%
0.0
1
MV high limit
–10.0 to +110.0%
100.0
1
P- 1 C
Cool-side
proportional band
0.1 to 999.9%
5.0
0
I- 1 C
Cool-side
integration time
0 to 9999s
(0: No integral control action)
120
0
Cool-side
derivative time
Cool-side MV low
limit
Cool-side MV high
limit
0 to 9999s
(0: No derivative control action)
–10.0 to +110.0%
OH. 1 C
CtrL
Cy
Time proportional cycle1
CyU2
Time proportional cycle unit 2
0
0
User
level
0
Cy2
Time proportional cycle 2
tP. ty
Time proportional operation
type
SPU
SPd
SP ramp-up
SP ramp-down
Display
E 1 to E5
Item
AT type
JF. bd
SP. LG
At-P
Just-FiTTER setting band
SP lag constant
Proportional band tuning
factor at AT
Integration time tuning factor
at AT
Derivative time tuning factor
at AT
Control algorithm
At-I
At-d
E 1. Sb to
E5. Sb
E 1. Hy to
E5. Hy
Internal event 1 to
5, main setting
Internal event 1 to
5, sub-setting
Internal event 1 to
5, hysteresis
E 1. On to
E5. On
E 1. OF to
E5. OF
Internal event 1 to
5, ON delay
Internal event 1 to
5, OFF delay
St.SA
Contents
–1999 to +9999
The decimal point position varies by meeting the
internal event operation type.
0 to 9999 for some operation type.
0 to 9999
The decimal point position varies by meeting the
internal event operation type.
0.0 to 999.9
(For the delay time unit 0.1s)
0 to 9999
(Except for the delay time unit 0.1s)
Initial
value
0
User
level
0
0
0
5
0
0
2
0
2
Item
At. ty
JF. Ov
■ Event bank
Bank selection: Ev
Cold junction
compensation
(T/C)
Decimal point
position
C 04
C 05
30
0
0.0
1
C 07
C 08
C 09
100.0
1
C 14
C 16
C 17
Contents
0: ON/OFF control
1: PID fixed
2: ST (Self turning)
–10.0 to +110.0%
–10.0 to +110.0%
0 to 9999U
–1999 to 9999U
0.0 to 120.0s
0.001 to 9.999
–1999 to +9999U
0: 1s unit
1: 0.5s fixed (Cycle time is disabled.)
2: 0.2s fixed (Cycle time is disabled.)
3: 0.1s fixed (Cycle time is disabled.)
5 to 120s (The output includes the relay
output.)
1 to 120s (The output does not include the
relay output.)
0: 1s unit
1: 0.5s fixed (Cycle time is disabled.)
2: 0.2s fixed (Cycle time is disabled.)
3: 0.1s fixed (Cycle time is disabled.)
5 to 120s (The output includes the relay
output.)
1 to 120s (The output does not include the
relay output.)
0: Controllability aiming type
1: Actuator life aiming type
(Only one ON/OFF operation within time
proportional cycle time)
0.0 to 999.9U (0.0: No ramp)
Initial
value
0 or 1
User
level
0
St.Sb
St.Hb
St.ud
Just-FiTTER overshoot
suppression factor
ST step execution resolution
width
ST step settling bound
ST hunting settling bound
ST step ramp change
C 18
C 19
0.0
100.0
5
0
0
0
0
2
0.0
1.000
0
0
0
1
0
2
C 20
C21
C 22
C 26
C 27
10 or 2
0
0
2
10 or 2
0
0 or 1
2
0.0
0.0
2
2
C 28
C 29
C 30
C 32
C 36
C 37
C 38
■ Extension tuning bank
Bank selection: Et
Ctr. A
Display
MV low limit at AT
MV high limit at AT
ON/OFF control differential
ON/OFF control operating
point differential
PV filter
PV ratio
PV bias
Time proportional cycle unit 1
0
Latch
continue
OFF
Initial
value
0
Item
Control method
0
0
Temperature unit
C 03
C 06
–10.0 to +110.0%
C 39
C 40
C41
C 42
C 43
Contents
0: Normal (Standard control characteristics)
1: Immediate response (Control
characteristics immediately responding
to the external disturbance.)
2: Stable (Control characteristics with less
up/down function of PV)
0.00 to 10.00
0.0 to 999.9
0.00 to 99.99
Initial
value
1
User
level
0
0.30
0.0
1.00
2
2
2
C 44
0.00 to 99.99
1.00
2
C 45
0.00 to 99.99
1.00
2
C 46
0
1
0
1
10.00
2
0: PID (conventional PID)
1: Ra-PID (high performance type)
0 to 100
C 47
C 48
0.00 to 99.99 %
C 49
0.00 to 10.00 %
0.00 to 10.00 %
0: ST is executed when the PV ramp up or
down.
1: ST is executed only when the PV ramp
up.
PV input range
type
0
■ Parameter bank
Bank selection: PArA
0
0
50.0
Item
C 02
C 15
0
RUN
0
MV low limit
0
AT Stop
0
30
OH- 1
FL
rA
bI
CyU
User
level
0
120
OL- 1
0
Initial
value
AUTO
User
level
0
Manual reset
0
-
Initial
value
5.0
rE- 1
At. OL
At. OH
dIFF
OFFS
-
Contents
0.1 to 999.9%
Display
0
■ SP bank
Bank selection: SP
Display
Item
Proportional band
OL. 1 C
0
C01
P- 1
d- 1 C
[List of Parameter Setting Displays]
■ Mode bank
Bank selection: MOdE
Display
■ PID bank
Bank selection: PId
Display
CP-UM-5287
[List of Setup Setting Displays]
■ Setup bank
Bank selection: StUP
0.50
1.00
0
2
2
1
3
C 50
C51
PV range low limit
PV range high
SP low limit
SP high limit
Squarer root
extraction dropout
Control action
(direct/reverse)
Selection of MV
at PV alarm
occurrence
MV at PV alarm
occurrence
MV at READY (at
heat-side for
heat/cool control)
MV at READY (at
cool-side)
Operation at
MANUAL change
Preset MANUAL
value
PID operation
initialization
function selection
PID operation
initial MV
Heat/cool control
Contents
Thermocouple (T): 1 to 6, 9 to 11, 13 to 21, 24, 25
RTD (R): 41 to 46, 51 to 54, 63, 64, 67, 68
DC current/voltage (L): 84, 86 to 90
0: Centigrade (°C)
1: Fahrenheit (°F)
0: Cold junction compensation is performed. (Internal)
1: Cold junction compensation is not performed.
(External)
0: No decimal point
1: One digit below decimal point
2: Two digits below decimal point
3: Three digits below decimal point
(Select ‘0’ or ‘1’ for the RTD range with decimal
point)
When the PV input range type is thermocouple (T) or
RTD (R), the setting is disabled although range low
limit is displayed.
–1999 to +9999U when the PV input range type is DC
voltage/current (L).
When the PV input range type is thermocouple (T) or
RTD(R), the setting is disabled although range high
limit is displayed.
–1999 to +9999U when the PV input range type is DC
voltage/current (L).
PV input range low limit to PV input range high limit
0.0 to 100.0%
(0.0: No square root extraction)
0: Heat control (reverse action))
1: Cool control (direct action)
0: Control operation is continued.
1: MV at PV alarm occurrence is outputted.
Initial
value
1
41
88
0
User
level
0
C 64
0
C 65
Station address
0
2
C 66
Transmission
speed
0
0
C 67
Data format (data
length)
Data format
(parity)
C 68
-
0
C 70
-
0
C71
C 72
1000
0
1000
0.0
1
1
2
0
0
0
2
–10.0 to +110.0%
0.0
2
0.0
1
–10.0 to +110.0%
0.0
1
0: Disabled.
1: Enabled.
Heal/cool selection 0: Normal
1: Energy saving
Dead zone
–100.0 to +100.0%
Heal/cool control
–10.0 to +110.0%
selection point
LSP setting
1 to 4
system
SP ramp unit
0: 0.1U/s
1: 0.1U/min
2: 0.1U/h
CT1 operation
0: Heater burnout detection
type
1: Current value measurement
CT1 output
0: Control output 1
1: Control output 2
2: Event output 1
3: Event output 2
4: Event output 3
CT1 measurement 30 to 300ms
wait time
CT2 operation type Same as CT1.
CT2 output
CT2 measurement
wait time
Control output 1
1: 4 to 2mA
range
2: 0 to 20mA
Control output 1
0: MV
type
1: Heat MV
2: Cool MV
3: PV
4: PV before ratio bias filter
5: SP
6: Deviation (PV-SP)
7: CT1 current value
8: CT2 current value
9: Invalid
10: SP+MV
11: PV+MV
Control output 1
–1999 to +9999
scaling low limit
(The decimal point position and unit may vary
Control output 1
depending on the control output 1 type.)
scaling high limit
Control output 1 0 to 9999
MV scaling
The decimal point position and unit are same as
for PV.
Control output 2
Same as control output 1.
range
Control output 2
type
Control output 2
–1999 to +9999
scaling low limit
(The decimal point position and unit may vary
Control output 2
depending on the control output 2 type.)
scaling high limit
Control output 2 0 to 9999
MV scaling
The decimal point position and unit are same as
for PV.
C 69
0
–10.0 to +110.0%
0: Bump-less
1: Preset
–10.0 to +110.0%
(Used even at MANUAL mode when power is ON.)
0: Automatic
1: Not initialized
2: Initialized (when SP value different from current
value is inputted.)
–10.0 to +110.0%
Display
0
1
0.0 or
50.0
0
1
0.0 or
50.0
0
2
0
1
0.0
50.0
0
2
C 73
C 74
2
0
1
0
1
2
0
0
0
0
C 75
C 76
30
0
0
0
30
0
0
0
1
0
0
0
C 77
C 78
C 79
0.0
0
100.0
0
200.0
0
1
0
C 80
C 90
C91
3
0
0
0
C 92
C 93
1000
0
200.0
0
Item
CPL/MODBUS
Data format (stop
bits)
Communication
minimum response
time
Key operation
mode/type
MODE key
function
Contents
0: CPL
1: MODBUS ASCII format
2: MODBUS RTU format
0 to 127
Communication is disabled when "0" is set.
0: 4800bps
1: 9600bps
2: 19200bps
3: 38400bps
0: 7bits
1: 8bits
0: Even parity
1: Odd parity
2: No parity
0: 1bit
1: 2bits
1 to 250ms
0: Standard type
1: Special type
0: Invalid
1: AUTO/MANUAL selection
2: RUN/READY selection
3: AT Stop/Start
4: LSP group selection
5: Release of all DO latches
6: Invalid
7: Communication DI1 selection
8: Invalid
MODE display
Whether the mode bank setup display is enabled or
setup
disabled is determined by the sum of the following
weighting:
Bit 0: AUTO/MANUAL display
0: Disabled, +1: Enabled
Bit 1: RUN/READY display
0: Disabled, +2: Enabled
Bit 3: AT stop/start display
0: Disabled, +8: Enabled
Bit 4: DO latch release
0: Disabled, +16: Enabled
Bit 5: Communication DI1 ON/OFF display
0: Disabled, +32: Enabled
Other invalid setup: 0, +4, +64, +128
PV/SP value
Whether the basic display is enabled or disabled is
display setup
determined by the sum of the following weighting:
Bit 0: PV display
0: Disabled, +1: Enabled
Bit 1: SP display
0: Disabled, +2: Enabled
Bit 2: LSP group No. display
0: Disabled, +4: Enabled
Other invalid setup: 0, +8
MV display setup Whether the basic display is enabled or disabled is
determined by the sum of the following weighting:
Bit 0: MV display
0: Disabled, +1: Enabled
Bit 1: Heat MV/cool MV display
0: Disabled, +2: Enabled
Bit 3: AT progress display
0: Disabled, +8: Enabled
Other invalid setup: 0, +4
Event setting value 0: In the operation display mode, the internal event
display setup
setting value is not displayed.
1: In the operation display mode, the internal event 1
setting value is displayed.
2: In the operation display mode, the internal event 1
to 2 setting value is displayed.
3: In the operation display mode, the internal event 1
to 3 setting value is displayed.
Event remaining
0: In the operation display mode, the ON/OFF delay
time display setup
remaining time of the internal event is not
displayed.
1: In the operation display mode, the ON/OFF delay
remaining time of the internal event 1 is displayed.
2: In the operation display mode, the ON/OFF delay
remaining time of the internal event 1 to 2 is
displayed.
3: In the operation display mode, the ON/OFF delay
remaining time of the internal event 1 to 3 is
displayed.
CT input current
0: In the operation display mode, the CT current
value display
value is not displayed.
setup
1: In the operation display mode, the CT1 current
value is displayed.
2: In the operation display mode, the CT1 to 2
current value is displayed.
User level
0: Basic configuration
1: Standard configuration
2: High function configuration
LED monitor
0: Disabled
1: Flashing at RS-485 communication signal
transmission
2: Flashing at RS-485 communication signal
receiving
3: OR (logical sum) of all DI status
4: Flashing at READY
Number of CT1 0: 800 turns
turns
1 to 40: CT turns devided by 100.
Number of CT1 0: 1 time
power wire loops 1 to 6: Number of times
Number of CT2 0: 800 turns
turns
1 to 40: CT turns devided by 100.
Number of CT2 0: 1 time
power wire loops 1 to 6: Number of times
Initial
value
0
User
level
0
0
0
2
0
1
0
0
0
0
0
3
2
0
2
1
0
255
1
15
1
15
1
0
1
0
1
0
1
0
0
0
2
8
2
1
2
8
2
1
2
(continued on back page)
■ Event assignment bank
Bank selection: EvCF
Display
E 1. C 1 to
E5. C 1
E 1. C2 to
E5. C2
E 1. C3 to
E5. C3
Item
Contents
Operation type of
internal event 1 to
5 configuration 1
0: No event
1: PV high limit
2: PV low limit
3: PV high/low limit
4: Deviation high limit
5: Deviation low limit
6: Deviation high/low limit
7: Deviation high limit (Final SP reference)
8: Deviation low limit (Final SP reference)
9: Deviation high/low limit (Final SP reference)
10: SP high limit
11: SP low limit
12: SP high/low limit
13: MV high limit
14: MV low limit
15: MV high/low limit
16: CT1 heater burnout/over-current
17: CT1 heater short-circuit
18: CT2 heater burnout/over-current
19: CT2 heater short-circuit
20: Loop diagnosis 1
21: Loop diagnosis 2
22: Loop diagnosis 3
23: Alarm (status)
24: READY (status)
25: MANUAL (status)
26: Invalid
27: During AT execution (status)
28: During SP ramp (status)
29: Control direct action (status)
30: ST execution (status)
31: Invalid
32: Timer (status)
33: High and low limits of MFB value
(Invalid in this unit)
Internal event 1 to Digits are called as 1st digit, 2nd digit, 3rd digit and
5 Configuration 2 4th digit from the right end digit.
1st digit:
0: Direct
Direct/Reverse
1: Reverse
2nd digit: Stand-by 0: None
1: Standby
2: Standby + Standby at SP change
3rd digit: EVENT
0: Continue
state at READY
1: Forced OFF
4th digit: Undefined 0
Internal event 1 to Digits are called as 1st digit, 2nd digit, 3rd digit and
5 Configuration 3 4th digit from the right end digit.
1st digit: Alarm OR 0: No event
1: Alarm direct + OR operation
2: Alarm direct + AND operation
3: Alarm reverse + OR operation
4: Alarm reverse + AND operation
2nd digit: Special 0: As normal execution
OFF
1: Event OFF at the event setting value (main)=0
3rd digit: Delay
0: 0.1s
time unit
1: 1s
2: 1min
4th digit:
0
Undefined
Initial
value
0
User
level
0
Display
dI 1. 3 to
dI3. 3
dI 1. 4 to
dI3. 4
dI 1. 5 to
dI3. 5
dI 1. 6 to
dI3. 6
dI 1. 7 to
dI3. 7
0000
0
0
0
0
0
0000
2
dI 1. 8 to
dI3. 8
dI 1. 9 to
dI3. 9
0
dI 1. 2 to
dI3. 2
Item
Internal contact 1
to 3
Operation type
Internal contact 1
to 3
Input bit operation
Contents
Digits are called as 1st digit, 2nd digit, 3rd digit and
4th digit from the right end digit.
0
User
level
2
2
0
2
0
2
Display
Ot 1. 6 to
Ot2. 6
Ev 1. 6 to
Ev3. 6
Ot 1. 7
Ot2. 7
Ev 1. 7
Ev3. 7
Ot 1. 8
Ot2. 8
Ev 1. 8
Ev3. 8
User
level
0
Ot 1. 2 to
Ot2. 2
Ev 1. 2 to
Ev3. 2
Ot 1. 3 to
Ot2. 3
Ev 1. 3 to
Ev3. 3
0
to
to
to
UF- 1
2
UF-2
UF-3
0: Direct
1: Reverse
0
UF-4
0
UF-5
0
UF-6
UF-7
0
UF-8
0: Direct
1: Reverse
0: Every internal event
1 to 5: Internal event numbers
0
2
0
2
2
Ot 1. 4 to
Ot2. 4
Ev 1. 4 to
Ev3. 4
Ot 1. 5 to
Ot2. 5
Ev 1. 5 to
Ev3. 5
Item
Contents
Initial
value
0000
User
level
2
0
0
0
0
0
2
0
2
Contents
Initial
value
User
level
This is the display in upper display. The setup
exception is as follows:
---- : Yet to be registered.
P-- : Proportional band of the PID group in use
I-- :
Integration time of the PID group in use
d-- : Derivative time of the PID group in use
rE-- : Manual reset of the PID group in use
OL-- : MV low limit of the PID group in use
OH-- : MV high limit of the PID group in use
P--C : Cool-side proportional band of the PID
group in use
I--C : Cool-side integration time of the PID group
in use
d--C : Cool-side derivative time of the PID group
in use
Ol.-C : Cool-side MV low limit of the PID group in
use
Oh.-C : Cool-side of MV high limit of the PID group
in use
----
1
----
1
----
1
----
1
----
1
----
1
----
1
----
1
Initial
value
0
User
level
0
Digits are called as 1st digit, 2nd digit, 3rd digit and
4th digit from the right end digit.
0: Direct
1: Reverse
0: Direct
1: Reverse
0: Disabled
1: Enabled (Latch at ON)
2: Enabled (Latch at OFF, except at the time of
initialization after power ON)
■ User function bank
Bank selection: UF
Display
0000
Item
Control output 1 to
2, event output 1 to
2 Polarity A to D
1st digit: Polarity A
2nd digit: Polarity B
3rd digit: Polarity C
4th digit: Polarity D
Control output 1
to 2, event output
1 to 3
Polarity
Control output 1
to 2, event output
1 to 3
Latch
Item
User function
definition 1
User function
definition 2
User function
definition 3
User function
definition 4
User function
definition 5
User function
definition 6
User function
definition 7
User function
definition 8
■ Lock bank
Bank selection: LOC
Item
LOC
Key lock
C. LOC
L. LOC
Communication
lock
Loader lock
PASS
Password display
PS 1A
PS2A
PS 1b
PS2b
Password 1A
Password 2A
Password 1B
Password 2B
■ DO assignment bank
Bank selection: dO
0
Initial
value
0
to
Display
Ot 1. 1 to
Ot2. 1
Ev 1. 1 to
Ev3. 1
0: No function
1: LSP group selection (0/+1)
2: LSP group selection (0/+2)
3: LSP group selection (0/+4)
4: Invalid
5: Invalid
6: Invalid
7: RUN/READY selection
8: AUTO/MANUAL selection
9: Invalid
10: AT Stop/Start
11: ST Disabled/Enabled
12: Control action direct/reverse selection (As per
setting/opposite operation of setting)
13: SP ramp Enabled/Disabled
14: PV hold (No-hold/Hold)
15: PV maximum value hold (No-hold/Hold)
16: PV minimum value hold (No-hold/Hold)
17: Timer Stop/Start
18: Release of all DO latches (Continue/Release)
19: Invalid
20: Invalid
0: Disabled. (Input of default)
1: Function 1 ((A and B) or (C and D))
2: Function 2 ((A or B) and (C or D))
3: Function 3 (A or B or C or D)
4: Function 4 (A and B and C and D)
Internal contact
1 to 3
Polarity A to D
1st digit: Polarity A
(Polarity of input
assignment A)
2nd digit: Polarity B
(Polarity of input
assignment B)
3rd digit: Polarity C
(Polarity of input
assignment C)
4th digit: Polarity D
(Polarity of input
assignment D)
Internal contact
1 to 3 Polarity
Internal contact
1 to 3
Internal event
No.assignment
Initial
value
2 to 4
0
■ DI assignment bank
Bank selection: dI
Display
Contents
0
Display
dI 1. 1 to
dI3. 1
Item
Internal contact
0: Normally open (OFF, 0)
1 to 3
1: Normally close (ON, 1)
Input assignment A 2: DI1
3: DI2
4 to 9: Undefined
10: Internal event 1
11: Internal event 2
Internal contact
12: Internal event 3
1 to 3
13: Internal event 4
Input assignment B 14: Internal event 5
15 to 17: Undefined
18: Communication DI1
19: Communication DI2
20: Communication DI3
Internal contact
21: Communication DI4
1 to 3
22: MANUAL mode
Input assignment C 23: READY mode
24: Undefined
25: During AT execution
26: During SP ramp
27: Undefined
Internal contact
28: Alarm is enabled.
1 to 3
29: PV alarm is enabled.
Input assignment D 30: Undefined
31: Mode key function selection status
32: Event output 1 status
33: Control output 1 status
Contents
Control output
0: Input of default
1 to 2, event output 1: MV1 (ON/OFF control output, time proportional
1 to 3 operation
output,heat-side proportional output of heat/cool
type
control)
2: MV2 (cool-side proportional output of heat/cool
control)
3: Function 1 ((A and B) or (C and D))
4: Function 2 ((A or B) and (C or D))
5: Function 3 (A or B or C or D)
6: Function 4 (A and B and C and D)
Control output
0: Normally open (OFF, 0)
1 to 2, event output 1: Normally close (ON, 1)
1 to 3 output
2: Internal event 1
assignment A
3: Internal event 2
4: Internal event 3
5: Internal event 4
6: Internal event 5
7 to 13: Undefined
14: MV1
Control output
15: MV2
1 to 2, event output 16 to 17: Undefined
1 to 3 output
18: DI1
assignment B
19: DI2
20 to 25: Undefined
26: Internal contact 1
27: Internal contact 2
28: Internal contact 3
29 to 33: Undefined
Control output
34: Communication DI1
1 to 2, event output 35: Communication DI2
1 to 3 output
36: Communication DI3
assignment C
37: Communication DI4
38: MANUAL mode
39: READY mode
40: Invalid
41: During AT execution
42: During SP ramp
Control output
43: Undefined
1 to 2 event output 44: Alarm is enabled.
1 to 3 output
45: PV alarm is enabled.
assignment D
46: Undefined
47: mode key function selection status
48: Event output 1 status
49: Control output 1 status
Initial
value
0
14 to 15
or
2 to 4
User
level
2
2
Id0 1
Id02
Id03
Id04
Id06
2
Id07
Id08
0
2
2
0
0
0000
0000
0000
0000
0
0
0
0
Initial
value
-
User
level
2
2
2
2
-
2
-
2
-
2
-
2
■ Instrument information bank
Bank selection: Id
Id05
0
0
0
2
Display
0
Contents
0: All settings are enabled.
1: Mode, event, operation display, SP, UF, lock,
manual MV, and mode key can be set.
2: Operation display, SP, UF, lock, manual MV, and
mode key can be set.
3: UF, lock, manual MV, and mode key can be set.
0: RS-485 communication read/write is enabled.
1: RS-485 communication read/write is disabled.
0: Loader communication read/write is enabled.
1: Loader communication read/write is disabled.
0 to 15
5: Password 1A to 2B display
0000 to FFFF (hexadecimal value)
0000 to FFFF (hexadecimal value)
0000 to FFFF (hexadecimal value)
0000 to FFFF (hexadecimal value)
Item
ROM ID
ROM version 1
ROM version 2
SLP support
Information
EST support
version
Manufacturing
date code (year)
Manufacturing
date code
(month, day)
Serial No.
Contents
0 fixed
XX. XX (2 digits after decimal point)
XX. XX (2 digits after decimal point)
Year - 2000
Ex.: “3” means the year 2003.
Month + Day 100
Ex.: “12.01” means the 1st day of December
2
Specifications are subject to change without notice.
Advanced Automation Company
1-12-2 Kawana, Fujisawa
Kanagawa 251-8522 Japan
Printed in Japan.
1st Edition: Issued in Feb. 2003 (A)
14th Edition: Issued in Jan. 2008 (A)
URL: http://www.azbil.com
Printed on recycled paper.
4
(07)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement