User Manual - Invacare Continuing Care

User Manual - Invacare Continuing Care
Invacare ®CS Series Beds
CS3, CS5, CS7, CS9, CS9FX600
User Manual
For more information regarding bed rail safety, refer to the Bed Rail
Entrapment Risk Notification Guide at www.invacare.com.
This manual MUST be given to the user of the product.
BEFORE using this product, read this manual and save for future reference.
EN
© 2012 Invacare Corporation. All rights reserved. Republication, duplication or modification in whole or in part is prohibited without prior written
permission from Invacare. Trademarks are identified by ™ and ®. All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries
unless otherwise noted.
Sherwin-Williams is a registered trademark of Sherwin-Williams.
Invacare ®CS Series Beds
2
Part No 1153410
CONTENTS
1
GENERAL
5
Symbols ......................................................................................................................................................................................................................................................5
Limited Warranty ....................................................................................................................................................................................................................................7
2
SAFETY
8
General Guidelines ..................................................................................................................................................................................................................................8
Operation Information ...........................................................................................................................................................................................................................9
EMI Information......................................................................................................................................................................................................................................14
3
EMC INFORMATION
16
Electromagnetic Compatibility (EMC) Information ......................................................................................................................................................................16
4
PRODUCT LABELING
21
5
TECHNICAL DATA
23
Typical Product Parameters ................................................................................................................................................................................................................23
Mattress Specifications..........................................................................................................................................................................................................................28
6
SET-UP
29
Unpacking Instructions .........................................................................................................................................................................................................................29
Assembly Instructions...........................................................................................................................................................................................................................32
7
USAGE
37
Hand Control - Pendant Operation ..................................................................................................................................................................................................37
Pendant Storage and Location ............................................................................................................................................................................................................39
Power Cord Storage .............................................................................................................................................................................................................................41
Raise and Lower the Heel Lift Ratchet.............................................................................................................................................................................................42
Foot Pad Lock Mechanism on CS3 Bed............................................................................................................................................................................................43
Bed Steer Mechanism............................................................................................................................................................................................................................44
Part No 1153410
3
Invacare ®CS Series Beds
CONTENTS
8
OPTIONS
45
Safety Information For Options..........................................................................................................................................................................................................45
Bed Rails and Positioning Devices......................................................................................................................................................................................................48
Other Accessories.................................................................................................................................................................................................................................48
Optional Drainage Bag Holder ...........................................................................................................................................................................................................49
Optional Touch-up Paint......................................................................................................................................................................................................................49
Optional Attendant Control Panel Operation................................................................................................................................................................................50
Optional Trendelenburg and Reverse Trendelenburg Attendant Control Panel ...................................................................................................................53
Pendant HI/LO Lock Out - Optional ................................................................................................................................................................................................54
Optional Cardiopulmonary Resuscitation (CPR) Release............................................................................................................................................................55
Optional 39 Inch and 42 Inch Wide Decks .....................................................................................................................................................................................57
Adjustable Width Bed Model CS9FX600.........................................................................................................................................................................................58
9
MAINTENANCE
63
Cleaning Instructions.............................................................................................................................................................................................................................63
Annual Maintenance Check .................................................................................................................................................................................................................64
Quarterly Maintenance Check............................................................................................................................................................................................................64
Environmental Conditions for Storage and Transport .................................................................................................................................................................64
Environmental Conditions for Operation ........................................................................................................................................................................................64
10 TROUBLESHOOTING
Invacare ®CS Series Beds
65
4
Part No 1153410
1 GENERAL
1 General
1.1
Symbols
Warnings
Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage.
See the information below for definitions of the signal words.

DANGER

WARNING

CAUTION
!

Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Caution indicates a potentially hazardous situation which, if not avoided, may result in property damage or minor injury or
both.
IMPORTANT
Indicates a hazardous situation that could result in damage to property if it is not avoided.
Gives useful tips, recommendations and information for efficient, trouble-free use.
Part No 1153410
5
Invacare ®CS Series Beds
1 GENERAL
Symbols used on the CS Bed
Battery Charging (Yellow)
(on Trend ACP)
Battery Fully Charged (Green)
Invacare ®CS Series Beds
6
Part No 1153410
1 GENERAL
1.2
Limited Warranty

PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS
MANUFACTURED AFTER JULY 4, 1975.
This warranty is extended only to the original purchaser who purchases this product when new and unused from Invacare Continuing Care, Inc (ICCI) or a dealer.
This warranty is not extended to any other person or entity and is not transferable or assignable to any subsequent purchaser or owner. Coverage under this
warranty will end upon any such subsequent sale or other transfer of title to any other person.
This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state.
ICCI warrants the frame and welds on this product when purchased new and unused will be free from structural defects on the frame for a period of ten (10)
years, electrical for a period of three (3) years, and mechanical for a period of five (5) years from date of purchase from ICCI or a dealer, with a copy of the
seller’s invoice required for coverage under this warranty. ICCI warrants the frame of this product when purchased new and unused to be free from defects in
materials and workmanship for a period of ten (10) years from date of purchase from ICCI or a dealer, with a copy of the seller’s invoice required for coverage under
this warranty. For all other components of this product when purchased new and unused, ICCI warrants that they will be free from defects in material and
workmanship for a period of one (1) year from date of purchase from ICCI or a dealer, with a copy of the seller’s invoice required for coverage under this
warranty. Upholstery (vinyls, fabrics and/or laminates) are not covered under this warranty. If within such warranty periods any such product shall be proven to
be defective, such product shall be repaired or replaced, at ICCI's option. This warranty does not include any labor or shipping charges incurred in replacement part
installation or repair of any such product. ICCI's sole obligation and your exclusive remedy under this warranty shall be limited to such repair and/or replacement.
For warranty service, please contact the dealer from whom you purchased your ICCI product. In the event you do not receive satisfactory warranty service, please
write directly to ICCI at the address on the back cover, provide dealer's name, address, and the date of purchase, indicate nature of the defect and, if the product is
serialized, indicate the serial number. Do not return products to our factory without our prior consent.
LIMITATIONS AND EXCLUSIONS: THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS
BEEN REMOVED OR DEFACED, PRODUCTS SUBJECTED TO NEGLIGENCE, ACCIDENT, IMPROPER OPERATION, MAINTENANCE OR STORAGE,
PRODUCTS MODIFIED WITHOUT ICCI'S EXPRESS WRITTEN CONSENT (INCLUDING, BUT NOT LIMITED TO, MODIFICATION THROUGH THE USE
OF UNAUTHORIZED PARTS OR ATTACHMENTS; PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE
SPECIFIC CONSENT OF ICCI, OR TO A PRODUCT DAMAGED BY CIRCUMSTANCES BEYOND ICCI'S CONTROL, AND SUCH EVALUATION WILL BE
SOLELY DETERMINED BY ICCI. THE WARRANTY SHALL NOT APPLY TO NORMAL WEAR AND TEAR OR FAILURE TO ADHERE TO THE PRODUCT
INSTRUCTIONS.
“THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES WHATSOEVER, WHETHER EXPRESS OR IMPLIED,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND THE SOLE REMEDY FOR
VIOLATIONS OF ANY WARRANTY WHATSOEVER, SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT PERSUANT TO
THE TERMS CONTAINED HEREIN. THE APPLICATION OF ANY IMPLIED WARRANTY WHATSOEVER SHALL NOT EXTEND BEYOND THE DURATION
OF THE EXPRESS WARRANTY PROVIDED HEREIN. ICCI SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
WHATSOEVER.”
Part No 1153410
7
Invacare ®CS Series Beds
2 SAFETY
2 Safety
The Safety section contains important information for the safe operation and use of this product.
2.1
General Guidelines


!
DANGER: RISK OF INJURY OR DEATH
Use ONLY Invacare rails, mattresses, bed extenders and other accessories with
Invacare bed products.
Bed accessories designed by other manufacturers have NOT been tested by Invacare.
Use of NON-Invacare bed accessories may result in injury or death.
WARNING
DO NOT use this product or any available optional equipment without first completely reading and understanding these
instructions and any additional instructional material such as owner’s manuals, service manuals or instruction sheets
supplied with this product or optional equipment. If you are unable to understand the warnings, cautions or instructions,
contact a healthcare professional, dealer or technical personnel before attempting to use this equipment - otherwise, injury
or damage may occur.
The initial set up of this bed must be performed by a qualified technician. Procedures other than those described in this
manual must be performed by a qualified technician.
NOTICE
THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
Check all parts for shipping damage and test before using. In case of damage, DO NOT use. Contact ICCI Customer
Service Department (1-800-668-2337)/Carrier for further instruction.
This Manual/Electric bed has been engineered to provide reliable operation. The bed has been thoroughly tested and
inspected prior to shipment.
Invacare ®CS Series Beds
8
Part No 1153410
2 SAFETY
2.2
Operation Information
General Warnings

WARNING
When bed is not to be used for an extended period, unplug electric bed from the wall outlet.
The electric bed is NOT designed to be used as a patient transport. When transporting a patient, use an approved patient
transport. Otherwise, injury or damage may result. If the unit is not working properly, call a qualified technician to examine the unit and repair it.
Keep all moving parts, including the main frame, mattress deck (head and foot sections) and all drive shafts, free of
obstruction (i.e. chair rails, consoles, window sills, blankets/sheets, heating blankets/pads, tubing, wiring, etc. and other types
of products using electric cords which may get tangled around the bed, side rails or legs) during operation of the electric
bed. Never store anything under the bed.
The electric bed is equipped with locking casters. When transferring into or out of the electric bed, always lock the locking
caster(s). Inspect the wheel locks for correct locking action before actual use. Even with casters properly locked some
flooring surfaces such as tile or wood will allow the bed to move under some conditions. Use on surfaces such as these
must be evaluated by the care provider.
After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely.
If a liquid is spilled in or around the electric bed, unplug the electric bed before cleaning. Clean up the spill and allow the
electric bed or the area around the electric bed to dry thoroughly before using the electric controls again.
When operating/moving electric beds, always ensure that the individual utilizing the bed is positioned properly within the
confines of the bed. DO NOT let any extremities protrude over the side or between the bed rails when performing these
functions.
Hang pendant on hook or secure with linen clip when not in use. Keep cord clear of moving parts. DO NOT roll the bed
over the power cord or pendant cord. DO NOT entangle the cords on other objects. A pinched electric cord is
dangerous and can become damaged. Use the Power Cord Strap when moving the bed. Refer to Pendant Storage and
Location on page 39 and Power Cord Storage on page 41.
Part No 1153410
9
Invacare ®CS Series Beds
2 SAFETY
Weight Limitation

WARNING
This bed is rated to 600 lbs. (272 kg) for model CS9FX600, 500 lbs. (228 kg) for models CS5, CS7, and CS9 and 450 lbs.
(204 kg) for model CS3. DO NOT overload the bed. The combined weight of patients, visitors, mattress, bedding and all
accessories must NOT exceed rated capacity or Safe Working Load.
Body weight should be evenly distributed over the surface of the bed. DO NOT lay, sit or lean in such a way that your
entire body weight is placed only on raised head or foot sections of the bed. This includes when assisting the user in
repositioning or transferring in or out of bed.
DO NOT drop the bed. DO NOT allow patients to fall on the bed. DO NOT jump on the bed.
Each of the preceding impacts can permanently damage either HI/LO motor resulting in an inoperable bed. In the case of
an inoperable bed due to a damaged HI/LO motor, the HI/LO motor must be replaced immediately. If left unattended, a
damaged HI/LO motor can cause the bed to fall from the highest extended position, resulting in patient injury. DO NOT
exceed the maximum continuous duty cycle. Refer to Technical Specifications.
NEVER allow patients to use trapeze or traction units as a total individual weight support. Trapeze units are to be used
only for immobilizing a patient in various traction set-ups or assisting the patient in repositioning or transferring into or out
of bed.
Entrapment Warnings

WARNING
Refer to the Bed Rail Entrapment Risk Notification Guide at www.invacare.com.
If patient assessment concludes that the patient’s condition increases the chance of entrapment, the bed MUST be in the flat
position when left unattended.
Invacare ®CS Series Beds
10
Part No 1153410
2 SAFETY
Repair or Service Information
Ꮨ
DANGER
After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely.
DO NOT open assemblies such as the motors, pendant, control boxes or gearboxes. No user serviceable parts are inside.
Only qualified technicians are permitted to repair these parts. If unqualified individuals perform any work on these beds, the
warranty is void.
Unplug the power cord from its power source before performing any maintenance on the electric bed. DO NOT unplug
the power cord from the control box. Damage to cord will result.
The control box is mounted to the head motor with a cable tie. If replacing the control box, remove the cable tie and slide
the control box away from the head motor until it is free. Disconnect all cable connections.
Before connecting/disconnecting the connections at the control box, make sure the cable lock is removed by lightly
depressing on the end tabs and lifting. After connectors are plugged in, route all cables into the cable lock slots and snap the
cable lock in place. When installing any connectors into the control box, be sure the cable lock is secure after installation otherwise, injury or damage may occur.
DO NOT force the connector into the control box, otherwise - injury or damage may occur.
Fire Hazard

DANGER
Possible fire hazard when used with oxygen administering equipment other than nasal or masked type.
Use masked or nasal type oxygen administering equipment only in conjunction with the manual/electric bed. The use of any
other type of oxygen administering equipment can result in a fire hazard.
When using nasal or masked type oxygen administering equipment, the oxygen or air tubing MUST be routed and secured
properly to ensure that the tubing does not become entangled and/or severed during normal operation of manual/electric
bed.
Part No 1153410
11
Invacare ®CS Series Beds
2 SAFETY
Explosion Hazard

DANGER
EXPLOSION Hazard. DO NOT operate this bed in the presence of a flammable anaesthetic mixture with air or with
nitrous oxide. DO NOT use near explosive gases.
Keep the product a minimum of 12" away from any direct heat source.
Electrical and Grounding
Ꮨ
DANGER
NEVER operate if the unit has a damaged cord or plug. If it is not working properly, call a qualified technician for
examination and repair. Keep all electrical cords away from heated or hot surfaces. Ensure all cables and cords are routed
such that they will not become entangled or pinched. Otherwise damage or injury may result.
If grounding is not reliable, unplug the bed and use the battery power, if equipped.
DO NOT unplug power cord from control box.
The pendant and power cords must be routed and secured properly to ensure that the cords DO NOT become
entangled, pinched and/or severed during operation of the electric bed.
NEVER operate the unit if these cords are damaged.
Refer servicing to qualified personnel only. Grounding reliability depends upon a properly grounded wall outlet.
Improper connection of the equipment-grounding conductor can result in electrocution. Check with a qualified electrician
or service person if you are doubtful that the electrical outlet is properly grounded. DO NOT modify the grounding plug
provided. If it will not fit into the electrical outlet, have a proper outlet installed by a qualified electrician. Grounding
reliability can only be achieved when connected to an equivalent receptacle marked Hospital Only or Hospital Grade.
In the event of a power outage, the bed can be powered by its internal battery but MUST remain plugged into the
grounded outlet for proper grounding.
Electric components, such as motors may cause severe injury including electrocution if exposed to water.
During routine bed operation or when cleaning, DO NOT expose electrical components to water. Unplug and deenergize electrical components when water products are near these components.
Invacare ®CS Series Beds
12
Part No 1153410
2 SAFETY
Ꮨ

WARNING
To de-energize the bed it must be unplugged from the wall outlet and the battery must be disconnected from the
controller to prohibit operation.
DO NOT use an extension cord.
DO NOT permit the cord, wall outlet, motors, control box or pendant to become wet or submerged.
DO NOT operate the bed if the cord or outlet is damaged. DO NOT operate the bed if any motor has malfunctioned or
is damaged in any manner.
DO NOT use this bed in Active Treatment “Ether Environments”.
Plug the three prong electrical cord ONLY into a properly grounded 110 VAC to 120 VAC, 60 cycle outlet that is rated to
at least six amps. This electric bed must be grounded. In the event of a malfunction or breakdown, grounding provides a
path of least resistance for electric current, thereby reducing the risk of electric shock.
This product is equipped with a cord having an equipment-grounding conductor and a grounded plug. The plug must be
inserted into an appropriate electric outlet that is properly installed and grounded in accordance with all local codes and
ordinances.
CAUTION
A safety feature of this product includes protection against overheating caused by excessive or extended periods of
operation. Depending on the duration, this includes multiple or repeated adjustments or the use of multiple functions at
one time. To assure trouble free operation, ALWAYS allow a slight pause between multiple adjustments and avoid pressing
more than one function button at a time. If thermal protection activation should occur, the bed will not respond to pendant
commands. Given this situation, release the pendant button and allow the bed unit to sit for several minutes. This will allow
the protection function time to reset and restore bed function. Depending on the severity of the initial overheating, this
could take up to 30 minutes.
Part No 1153410
13
Invacare ®CS Series Beds
2 SAFETY
Battery

2.3
WARNING
Charge battery through the controller. NEVER attempt to charge the battery by any other means.
Internal battery should be tested monthly.
EMI Information

CAUTION
IT IS VERY IMPORTANT THAT YOU READ THIS INFORMATION REGARDING THE POSSIBLE EFFECTS OF
ELECTROMAGNETIC INTERFERENCE ON THIS PRODUCT.
Electromagnetic Interference (EMI) From Radio Wave Sources
This product may be susceptible to electromagnetic interference (EMI), which is interfering electromagnetic energy (EM) emitted from sources such
as radio stations, TV stations, amateur radio (HAM) transmitters, two way radios, and cellular phones. The interference (from radio wave sources)
can cause the powered bed to release its brakes, move by itself, or move in unintended directions. It can also permanently damage the powered bed's
control system. The intensity of the interfering EM energy can be measured in volts per meter (V/m). Each powered bed can resist EMI up to a certain
intensity. This is called its “immunity level.” The higher the immunity level, the greater the protection. At this time, current technology is capable of
achieving at least a 20 V/m immunity level, which would provide useful protection from the more common sources of radiated EMI.
There are a number of sources of relatively intense electromagnetic fields in the everyday environment. Some of these sources are obvious and easy
to avoid. Others are not apparent and exposure is unavoidable. However, we believe that by following the warnings listed below, your risk to EMI
will be minimized.
The sources of radiated EMI can be broadly classified into three types:
1. Hand-held Portable transceivers (transmitters-receivers with the antenna mounted directly on the transmitting unit. Examples include: citizens
band (CB) radios, “walkie talkie”, security, fire and police transceivers, cellular telephones, and other personal communication devices).

2.
Some cellular telephones and similar devices transmit signals while they are ON, even when not being used.
Medium-range mobile transceivers, such as those used in police cars, fire trucks, ambulances and taxis. These usually have the antenna mounted
on the outside of the vehicle; and
Invacare ®CS Series Beds
14
Part No 1153410
2 SAFETY
3.
Long-range transmitters and transceivers, such as commercial broadcast transmitters (radio and TV broadcast antenna towers) and amateur
(HAM) radios.

Other types of hand-held devices, such as cordless phones, laptop computers, AM/FM radios, TV sets, CD players, cassette
players, and small appliances, such as electric shavers and hair dryers, so far as we know, are not likely to cause EMI
problems to this product.
Pinch Point

WARNING
Pinch point between rail and floor is created when lowering the bed to the lowest position.
Keep feet clear of bed when lowering bed.
Close supervision is necessary when this product is used near or by children or people with disabilities. DO NOT let any
individual underneath the bed or in between the raised bed frame components at any time.
Disposal
WARNING
This product has been supplied from an environmentally aware manufacturer that complies with the Waste Electrical and
Electronic Equipment (WEEE) Directive 2002/96/CE.
This product may contain substances that could be harmful to the environment if disposed of in places (landfills) that are
not appropriate according to legislation. Please be environmentally responsible and recycle this product through your recycling facility at its end of life.
Part No 1153410
15
Invacare ®CS Series Beds
3 EMC INFORMATION
3 EMC Information
3.1
Electromagnetic Compatibility (EMC) Information
Medical Electrical Equipment needs special precautions regarding EMC and needs to be installed and put into service
according to the EMC information provided in this manual.
Portable and mobile RF communications equipment can affect medical electrical equipment.


WARNINGS
The use of accessories, tranducers, and cables other than those specified by the manufacturer, may result in increased
emissions or decreased immunity of this bed.
This bed should not be used adjacent to or stacked with other equipment and that if adjacent or stacked use is necessary,
this bed should be observed to verify normal operation in the configuration in which it will be used.
Guidance and Manufacturer’s Declaration - Electromagnetic Emissions
The CS Bed is intended for use in the electromagnetic environment specified below. The customer or the user of the CS Bed should assure that it is used
in such an environment.
Emissions Test
Compliance
Electromagnetic Environment - Guidance
RF emissions
CISPR 11
Group 1
The CS Bed uses RF energy only for its internal function. Therefore, its RF emissions
are very low and are not likely to cause any interference in nearby electronic
equipment.
RF emissions
CISPR 11
Class B
Harmonic emissions IEC 61000-3-2
Class A
The CS Bed is suitable for use in all establishments, including domestic
establishments and those directly connected to the public low-voltage power supply
network that supplies buildings used for domestic purposes.
Voltage fluctuations / flicker emissions
IEC 61000-3-3
Invacare ®CS Series Beds
Complies
16
Part No 1153410
3 EMC INFORMATION
Guidance and Manufacturer’s Declaration - Electromagnetic Immunity
The CS Bed is intended for use in the electromagnetic environment specified below. The customer or the user of the CS Bed should assure that it is used
in such an environment.
Immunity Test
IEC 60601 Test
Level
Compliance Level
Electromagnetic Environment – Guidance
Electrostatic discharge (ESD)
IEC 61000-4-2
±6 kV contact
±8 kV air
±6 kV contact
±8 kV air
Floors should be wood, concrete or ceramic tile. If floors are
covered with synthetic material, the relative humidity should be at
least 30 %.
Electrical fast transient/burst
IEC 61000-4-4
±2 kV for power
supply lines
±2 kV for power supply
lines
Mains power quality should be that of a typical commercial or
hospital environment.
±1 kV for input/output
lines
±1 kV for input/output
lines
Surge
IEC 61000-4-5
±1 kV differential
mode
±2 kV common mode
±1 kV differential mode
±2 kV common mode
Mains power quality should be that of a typical commercial or
hospital environment.
Voltage dips, short
interruptions and voltage
variations on power supply
input lines IEC 61000-4-11
<5 % UT
(>95 % dip in UT)
<5 % UT
(>95 % dip in UT)
for 0,5 cycle
for 0,5 cycle
40 % UT
(60 % dip in UT)
40 % UT
(60 % dip in UT)
Mains power quality should be that of a typical commercial or
hospital environment. If the user of the CS Bed requires continued
operation during power mains interruptions, it is recommended that
the CS Bed be powered from an uninterruptible power supply or a
battery.
for 5 cycles
for 5 cycles
70 % UT
(30 % dip in UT)
70 % UT
(30 % dip in UT)
for 25 cycles
for 25 cycles
<5 % UT
(>95 % dip in UT)
<5 % UT
(>95 % dip in UT)
for 5 sec
for 5 sec
Part No 1153410
17
Invacare ®CS Series Beds
3 EMC INFORMATION
Guidance and Manufacturer’s Declaration - Electromagnetic Immunity
Power frequency (50/60 Hz)
magnetic field IEC 61000-4-8
3A/m
3A/m
Power frequency magnetic fields should be at levels characteristic of
a typical location in a typical commercial or hospital environment.
NOTE UT is the a.c. mains voltage prior to application of the test level.
Guidance and Manufacturer’s Declaration - Electromagnetic Immunity
The CS Bed is intended for use in the electromagnetic environment specified below. The customer or the user of the CS Bed should assure that it is used
in such an environment.
Immunity Test
IEC 60601
Test Level
Compliance
Level
Electromagnetic Environment – Guidance
Portable and mobile RF communications equipment should be used no closer to
any part of the CS Bed, including cables, than the recommended separation
distance calculated from the equation applicable to the frequency of the
transmitter.
Recommended separation distance
Conducted RF
IEC 61000-4-6
3 Vrms
150 kHz to 80
MHz
Invacare ®CS Series Beds
3 Vrms
d=1.2
18
P
Part No 1153410
3 EMC INFORMATION
Guidance and Manufacturer’s Declaration - Electromagnetic Immunity
Radiated RF
IEC 61000-4-3
3 V/m
80 MHz to 2,5
GHz
3 V/m
d=1.2
P 80 MHz to 800 MHz
d=2.3 P 800 MHz to 2,5 GHz
where P is the maximum output power rating of the transmitter in watts (W)
according to the transmitter manufacturer and d is the recommended separation
distance in metres (m).
Field strengths from fixed RF transmitters, as deter-mined by an electromagnetic site
survey, a should be less than the compliance level in each frequency range. b
Interference may occur in the vicinity of equipment marked with the following
symbol:
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and
people.
a
b
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM
radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF
transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the CS Bed is used exceeds
the applicable RF compliance level above, the CS Bed should be observed to verify normal operation. If abnormal performance is observed, additional
measures may be necessary, such as re-orienting or relocating the CS Bed.
Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
Part No 1153410
19
Invacare ®CS Series Beds
3 EMC INFORMATION
Recommended separation distances between portable and mobile RF communications equipment and
the CS Bed
The CS Bed is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the CS
Bed can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment
(transmitters) and the CS Bed as recommended below, according to the maximum output power of the communications equipment.
Rated maximum output power of
transmitter
W
Separation distance according to frequency of transmitter
m
150 kHz to 80 MHz
d=1.2
80 MHz to 800 MHz
d=1.2
P
P
800 MHz to 2,5 GHz
d=2.3
0.01
.12
.12
.23
0.1
.38
.38
.73
1
1.2
1.2
2.3
10
3.8
3.8
7.3
100
12
12
23
P
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in metres (m) can be estimated using the
equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the
transmitter manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and
people.
Invacare ®CS Series Beds
20
Part No 1153410
4 PRODUCT LABELING
4 Product Labeling
Patient entrapment may cause injury or death. All eight adjustable deck sections MUST be set to the same width: 36 in, 39 in
or 42 in. If using a head board with the CS9FX600 model bed, an adjustable head board, model IHBEADJ, must be used.
Headboard must be set for the same width as the bed. Follow the manufacturer’s instructions for adjusting bed and head
board. Mattress must fit bed frame and side rails and assist devices snugly to prevent patient entrapment. Read and
understand the User Manual prior to using this equipment. ICCI manuals are available at www.invacare-cc.com or your
dealer.
Part No. 1158523 Rev B
Around Optional CPR
Release Bar
For Optional CPR Release
(On Both Sides of Bed)
Foot End
Head End
Serial
Number
Label
ETL Label - 120 V (CS3, CS5, CS7, CS9, and CS9FX600)
ETL Label - 230 V (CS5, CS7, CS9)

Part No 1153410
On Both Sides of Bed
of CS9FX600
WARNING
AVERTISSEMENT
Un patient peut être blessé ou même mourir s'il est coincé. Les huit sections de plateformes ajustables DOIVENT être de
même largeur : 90; 97,5 ou 105 cm. Pour l'utilisation d'une tête de lit avec le modèle CS9FX600, vous devez utiliser la tête de
lit réglable de modèle IHBEADJ. La tête de lit doit être de même largeur que le lit. Suivez les instructions du fabricant pour le
réglage du lit et de la tête de lit. Le matelas doit s'adapter à l'encadrement et aux longs pans et s'adapter correctement aux
dispositifs pour éviter le coincement du patient. Il est important de lire et de comprendre le manuel de l'utilisateur avant
d'utiliser cet équipement. Vous trouverez les manuels ICCI sur le site www.invacare-cc.com ou chez votre détaillant.
AVERTISSEMENT
Risque d'écrasement occasionné par la ZONE DE
MARGE FAIBLE DU LIT. Éloignez-vous de
l'encadrement et assurez-vous qu'aucun enfant ou
animal ne se trouve sous ou près de l'encadrement
du lit avant de l'abaisser. Faites attention aux POINTS
DE PINCEMENT situés sous les panneaux près des
fixations d'accessoires et entre les pièces mobiles.
All labels applied to bed frame except where noted.
21
WARNING
Crush Hazard due to LOW BED CLEARANCE.
Stay clear of frame and ensure children and
pets are not under or near the frame before
lowering the bed. Beware of PINCH POINTS
below deck panels, next to fixed attachments
and between moving parts.
1158522 Rev A
On Both Sides
of Bed
Invacare ®CS Series Beds
4 PRODUCT LABELING
Optional Foot End Board ACP
with Trendelenburg
Invacare ®CS Series Beds
22
Part No 1153410
5 TECHNICAL DATA
5 Technical Data
5.1
Typical Product Parameters
Certifications
All models (120 V~ models - CS3, CS5, CS7, CS9, CS9FX600 and 230 V~ models - CS5, CS7, CS9) conform to UL60601-1 and IEC606011. Certified to IEC60601-2-38 and IEC60601-1-2 and CAN/CSA C22.2 No. 601.1. 230 V~ models - CS5 and CS7 are CE marked for
Australia and New Zealand.
Elevation Range (floor to deck)
CS3
Stability Range
(casters locked or off casters)
Mobility range (on casters)
CS5
8¼ to 26½ in
(211 to 686
mm)
8¼ in (211 mm)
only
9 to 30 in
(229 to
762 mm)
Angle between back section (head deck)
and deck platform
CS9
7 to 30 in
(178 to 762
mm)
CS9FX600
9 to 30 in
(229 to 762 mm)
0° to 70°
Angle between back section and upper
leg section
Trendelenburg or reverse trendelenburg
(when configured)
CS7
>90°
not available
Under-bed clearance for 2/3 of bed centered
0° to 14° (Optional)
14 in (356 mm)
2
Part No 1153410
23
Invacare ®CS Series Beds
5 TECHNICAL DATA
Electrical Specifications
CS3
Control box mains voltage
CS5
CS7
120V~ or
230V~
120V~
Control box input current
CS9
120V~ or
230V~
3.5A max
3.5A max
(1.5A max
for 230V~
models)
3.5A max
60 Hz
60 Hz (50
Hz for 230
V models
60 Hz (50
Hz for 230 V
models
60 Hz (50
Hz for 230
V models
60 Hz
24 VDC (70W max)
Control box duty cycle
10% Max (2 min ON 18 min OFF)
Motorized linear head actuator
24 Volts DC
Motorized linear actuators (head, foot,
and HI/LO)
24 Volts DC
standard
not available
not available
standard (10 button optional)
Attendant control panel (ACP)
Trendelenburg ACP
Invacare ®CS Series Beds
120V~
3.5A max
(1.5A max
for 230V~
models)
Control box output voltage
Eight button hand pendant with contour
function
120V~ or
230V~
3.5A max
(1.5A max
for 230V~
models)
Control box current frequency
Six button hand pendant
CS9FX600
optional
not available
24
optional
Part No 1153410
5 TECHNICAL DATA
Safety Features
CS3
CS5
CS7
Protective earth ground
Class I
Electric shock protection
Type B
Enclosure protection
Floor lock
CS9
CS9FX600
IPX4
not available
CPR release on head actuator
Optional
standard
not available
optional
not available
optional
(standard with Trendelenburg 24V DC 9.2
Amps)
Built-in battery back-up
Security - Pendant Lock-Out
CS3
CS5
CS7
Pendant connection from either side
of bed
standard
ACL (attendant control lock-out)
pendant HI/LO function lock-out
optional
Individual pendant function lock-out
on ACP
optional
Part No 1153410
25
CS9
CS9FX600
Invacare ®CS Series Beds
5 TECHNICAL DATA
Dimensions and Weight
CS3
CS5
CS7
CS9
CS9FX600
Length (overall)
76 in and 80 in CS Beds
84¼ in (2140 mm)
80 in CS Bed with 4 in Extension
88¼ in (2242 mm)
Length between head and foot ends
76 in CS Bed
78½ in (1994 mm)
80 in CS Bed
82½ in (2096 mm)
80 in CS Bed with 4 in Extension
86½ in (2197 mm)
Length, mattress platform
76 in CS Bed
76 in (1930 mm)
80 in CS Bed
80 in (2032 mm)
80 in CS Bed with 4 in Extension
84 in (2134 mm)
Width, mattress platform
36 in Standard Deck
35½ in (901 mm)
39 in Wide Deck
38½ in (978 mm)
42 in Wide Deck
41½ in (1054 mm)
Width with assist rails - 36 in standard
deck
Invacare ®CS Series Beds
39¼ in (997 mm)
26
Part No 1153410
5 TECHNICAL DATA
CS3
CS5
CS7
CS9
CS9FX600
Width with Thinksoft® positioning
devices
36 in Standard
41¼ in (1048 mm)
39 in Wide
44¼ in (1124 mm)
42 in Wide
47¼ in (1200 mm)
Weight
36 in Standard Deck
186 lb (84 kg)
190 lb (86 kg)
not available
39 in Wide Deck
196 lb (89 kg)
200 lb (91 kg)
not available
42 in Wide Deck
199 lb (90 kg)
203 lb (92 kg)
not available
CS9FX600 Adjustable Deck
Load capacity - safe working load
4 in bed length extension
39 in or 42 wide bed deck
N/A
450 lb (204 kg)
optional
Not Available
27
600 lb (272 kg)
optional
optional
Not compatible with 68 inch rail.
Adjustable Deck
Part No 1153410
206 lb
500 lb (227 kg)
not available
Standard
Not compatible
with 68 inch rail
Invacare ®CS Series Beds
5 TECHNICAL DATA
5.2
Mattress Specifications

WARNING
Possible patient ENTRAPMENT Hazard if using non-specified mattress.
Refer to the Bed Rail Entrapment Risk Notification Guide at www.invacare.com.
Use only a mattress of recommended specifications with this bed.
A mattress may not be included with this bed. It is highly recommended that you use an Invacare branded mattress that is designed to
conform to the following dimensions:
Length
Width
Thickness
Invacare ®CS Series Beds
Named Size
Minimum Size
Maximum Size
76 in (1930.4 mm)
75 in (1905 mm)
76 in (1930.4 mm)
80 in (2032 mm)
79 in (2006.6 mm)
80 in (2032 mm)
84 in (2133.6 mm)
83 in (2108.6 mm)
84 in (2133.6 mm)
36 in (914 mm)
35.5 in (911 mm)
36.5 in (927 mm)
39 in (991 mm)
38.5 in (978 mm)
39.5 in (1004 mm)
42 in (1067 mm)
41.5 in (1054 mm)
42.5 in (1080 mm)
6 in (152 mm)
5.88 in (149 mm)
6.12 in (155 mm)
28
Part No 1153410
6 SET-UP
6 Set-Up
6.1
Unpacking Instructions

CAUTION
Equipment DAMAGE may result from improper wire tie removal.
DO NOT cut any trimmed plastic wire ties. Cut only the untrimmed plastic ties around the wood spacer. All other plastic
ties are used to secure the electric cables in place and should not be cut.
1.
Steady upright bed.
Part No 1153410
2.
Slowly lower to floor - use two people if
necessary.
29
3.
Slide off end boxes and remove plastic sleeve.
Invacare ®CS Series Beds
6 SET-UP

WARNING
Bed DAMAGE or personal INJURY may occur if the bed is dropped.
Ensure the bed is lowered slowly to the floor. Use additional people, if necessary.
4.
Invacare ®CS Series Beds
Remove wood spacer from front end of bed by 5.
lifting it off of bed end brackets.
30
Cut the untrimmed or green tie holding the
head deck to the frame.
Part No 1153410
6 SET-UP
6.
Cut the untrimmed or green plastic tie holding 7.
the knee-foot panel to the frame.
9.
Carefully cut the untrimmed or green tie holding 10. Carefully cut the untrimmed or green tie holding 11. Plug power cord into a properly grounded
the pendant bundle.
the mains cable bundle.
outlet.
Part No 1153410
Cut the untrimmed or green tie holding the
mattress keepers on either side of the bed.
31
8.
Cut the untrimmed or green ties holding the
mattress keepers at the end of the bed.
Invacare ®CS Series Beds
6 SET-UP
1.
6.2
Cut the untrimmed or green tie while holding the 2.
wall bumper.
Press HI/LO UP button on the hand pendant.
3.
Rotate the wall bumper to the floor at the head
end of the bed.
Assembly Instructions
Install the Mattress Keeper Rod to the Head and Foot Decks


WARNING
The mattress keeper rods are an integral part of the bed rail system. By securing the mattress in place, the mattress keeper
rods prevent unsafe gaps from forming between the bed ends or rails and the mattress. Install the mattress keeper rods
correctly to decrease the risk of patient entrapment.
The mattress keeper rods hold the mattress in place. Install them in the head and foot decks.
Invacare ®CS Series Beds
32
Part No 1153410
6 SET-UP
1.
All Models Except CS9FX600
All Models Except CS9FX600
All Models Except CS9FX600
Model CS9FX600
Model CS9FX600
Model CS9FX600
With the mattress keeper upright, insert the
rod ends into the appropriate deck holes.
Part No 1153410
2.
There are two choices for mattress keeper rod 3.
insertion. (76 in bed option shown above)
33
Mattress keeper rod insertion on 80 in Bed.
Invacare ®CS Series Beds
6 SET-UP
All Models Except CS9FX600
4.
Model CS9FX600
Fold the mattress keeper around the bed in the rod. The mattress keepers should rest flat on the foot 5.
deck and the head deck.
80 in bed position shown.
6.
76 in Bed Only - Remove the fasteners on the
bed end bracket.
Invacare ®CS Series Beds
7.
76 in Bed Only - Slide the bed end bracket in the 8.
mounting channel. Align the hole in the bracket
with the channel hole.
34
76 in Bed Only - With a 7/16 in socket wrench
and 7/16 in wrench loosen and remove the bed
end bracket fasteners.
76 in Bed Only - Reinsert the bed end bracket
fasteners.
Part No 1153410
6 SET-UP
All Models Except CS9FX600
9.
Model CS9FX600
76 in Bed Only - Tighten the fasteners with two 10. Position the mattress on the deck.
7/16 in wrenches. Reposition the other three 11. Press the mattress inside the mattress keeper. Ensure the mattress is engaged on all four corners.
brackets and reapply the ends.
Install Head and Foot Ends

Head and foot ends are normally packaged together either in a cardboard box or on a wooden skid separate from the bed.
Bed end model IHBEADJ must be used with bed model CS9FX600. Refer to Adjusting the Head Board Width for
CS9FX600 on page 62.
Part No 1153410
35
Invacare ®CS Series Beds
6 SET-UP
1.
Remove the key from the
keyhole.
Bed end not shown.
2.
Position Head End next to the
head board bracket. Hook the
head post screws in the bracket
slots.
3.
Slide the boards down while plate/ 4.
post screws are in the bracket
slots.
Position Foot End next to the foot
board brackets. Hook the board
screws into the bracket slots.
Foot end shown.
NOTE: Some
models only
have one
connection.
5.
Guide the key through the small bracket hole.
The key is attached to the bed bracket with a
lanyard.
Invacare ®CS Series Beds
6.
Turn and lock the key once it is fully inserted. 7. Attach the cables from the foot end board to the
Repeat on the other side, then the opposite bed
bed cables (ACP cable and pendant coupling).
end, securing both mounting points on each
Tighten the nut*.
board.
*ACP bed only.
36
Part No 1153410
7 USAGE
7 Usage
7.1
Hand Control - Pendant Operation

CAUTION
CRUSH Hazard.
DO NOT place feet under the frame when lowering the bed.
3 Function Pendant
Raise/Lower
Head
Raise/Lower
Bed
Raise/Lower
Knee
FIGURE 1 3 Function Pendant
Part No 1153410
37
Invacare ®CS Series Beds
7 USAGE
4 Function Pendant
Raise/Lower
Head
Alternate Pendants
Raise/Lower
Knee
Under
the Bed
Light
Nurse
Call
Raise/Lower
Bed
Raise/Lower
Head and Knee
FIGURE 2 4 Function Pendant
Invacare ®CS Series Beds
38
Part No 1153410
7 USAGE
7.2
Pendant Storage and Location
Ꮨ
DANGER
Electrical SHOCK Hazard.
Before working on any electrical part, such as the 9-pin pendant coupling, ensure the main power to the bed is
disconnected and the capacitor inside the control box is fully discharged.
Full capacitor discharge can be achieved by sequentially depressing the ‘Up’ and ‘Down’ buttons on the hand pendant at
least 20 times after main electrical power to the control box is cut. Ensure the hand pendant is not locked-out when
discharging it.
1.
Place the pendant holster between the top 2.
rail bars.
Part No 1153410
Slide the pendant into the holster.
39
3.
Alternatively, use the pendant clip to
secure the pendant to bed linen.
Invacare ®CS Series Beds
7 USAGE
6.
4.
The pendant can also be attached to the
back of either side of the Head end.
5.
To move the pendant to the other side of
the bed, disconnect the main power then
unscrew the coupling cap on the pendant
cable.
7.
On the other side of the bed, remove the
cap from the Y cable housing. Replace the
cap on the other side of the bed.
8.
Align arrows then insert the pendant cable 9.
end into the Y cable housing.
Invacare ®CS Series Beds
40
Remove the cable end from the Y cable
housing.
Screw the coupling cap to the threaded Y
cable housing end.
Part No 1153410
7 USAGE
7.3
Power Cord Storage

Disconnect the main power cable from the wall outlet and store the power cord when the bed is not in use.
1.
Secure the power cord to the back of the head end with the hook and loop strap when moving the
bed.
2.
Excess power cord can be secured to the back of head end with the hook and loop strap.
Part No 1153410
41
Invacare ®CS Series Beds
7 USAGE
7.4
Raise and Lower the Heel Lift Ratchet
1.
With knee-foot platform adjusted to the
highest position, lift the foot panel.
4.
The platform cannot lower past the nearest 5.
stop while being adjusted.
Invacare ®CS Series Beds
2.
The foot section can rest at any of the six
pre-set stops.
3.
To reset the ratchet mechanism, raise the 6.
platform to the highest level then lower the
platform in one motion.
42
Slowly lower the platform to engage the
nearest stop.
At the lowest position the deck can once
again be raised to the desired stop.
Part No 1153410
7 USAGE
7.5
Foot Pad Lock Mechanism on CS3 Bed

CAUTION
Moving the bed while the floor lock, caster lock, or foot pad is engaged may DAMAGE the bed.
DO NOT move the bed unless the floor lock, caster lock, or foot pad is disengaged (unlocked).
Mobility
Stability Range
Bed at the Lowest Position
FIGURE 3 Foot Pad Lock Mechanism on CS3 Bed
Part No 1153410
43
Invacare ®CS Series Beds
7 USAGE
7.6
1.
Bed Steer Mechanism
Steer mechanism is on either side of the
head end of the bed.
Invacare ®CS Series Beds
2.
With the locking wheel tab facing outward, 3.
flip the steer mechanism.
44
When engaged the bed will steer easily.
Part No 1153410
8 OPTIONS
8 Options

8.1
WARNING
After ANY adjustment, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely.
Failure to tighten hardware securely may result in injury or damage.
Safety Information For Options

WARNING
Refer to the Bed Rail Entrapment Risk Notification Guide at www.invacare.com.
Patient ENTRAPMENT with Assist Rail or Assist Bar may cause injury or death. Mattress must fit snugly within the mattress
keepers to prevent patient entrapment. Use only a mattress of recommended specifications with the bed. Monitor patient
frequently. Asses the needs of the resident prior to using the Assist Rail or Assist Bar.
Incorrect mounting of the assist rail or assist bar may result in patient entrapment. To reduce the risk of entrapment,
mount the assist rail or assist bar as shown in the instructions included with the rails or bars.
Crush Hazard exists between assist Rail or Assist Bar and Floor at the lowest bed position. Lowering the bed may cause
INJURY to oneself or others.
Lockout the Hand Control when working near the bed and DO NOT place feet or limbs in the crush zone located beneath
the Assist Rail or Assist Bar.
Part No 1153410
45
Invacare ®CS Series Beds
8 OPTIONS

WARNING
Patient entrapment with bed rails/assist devices or 68 Inch Rail may cause injury or death. Mattress must fit snugly within
the mattress keepers to prevent patient entrapment. Use only a mattress of recommended specifications with the bed.
Monitor patient frequently. Assess the needs of the resident prior to using the bed rails/assist devices.
Incorrect mounting of the bed rails and assist devices or 68 Inch Rail may result in PATIENT ENTRAPMENT. To reduce
the risk of entrapment, mount the bed rails/assist devices or 68 Inch Rail as shown in the instructions.
When a PATIENT’S condition (such as disorientation due to medical or clinical conditions) could lead to Patient
Entrapment, the mattress support platform should be left in the flat position while unattended (except when required
otherwise by medical staff for special or particular circumstances).
Use of incompatible trapeze units may cause injury and/or damage. Use only Invacare trapeze systems designed specially for
the CS bed: Standard Trapeze (1153385) or Heavy Duty Trapeze (1153386).
Use of trapeze may be hazardous to residents or guests. Possible entanglement may result from improper use of trapeze.
Evaluate residents prior to allowing them to use a trapeze. Never allow children to use, play, or swing on the trapeze.
The Standard and Heavy Duty Trapeze are designed to provide support, increased stability and assist the user when
repositioning himself/herself in bed. The Standard and Heavy Duty Trapeze are NOT designed, however, to support the
total body weight of an individual. Use it for assistance ONLY.
Tipping hazard. When in use, always rotate the trapeze until the handle is located over the center of the bed and ensure
that it drops down into the anti-rotation position.
Improper mattress placement may result in PATIENT ENTRAPMENT.
To ensure FDA Rail Guidelines are met, use ONLY the 84 inch CS bed kit with a mattress that is 84 inch (2137 mm) long.
An 80 inch mattress with a 4 inch extension pad MUST NOT be used in any circumstance. Mattress MUST fit bed frame
and assist rails snugly to reduce the risk of entrapment.
Invacare ®CS Series Beds
46
Part No 1153410
8 OPTIONS

WARNING
Safe Working Load of the Standard Trapeze is 168 lb. (750 N). DO NOT exceed 168 lb. (750 N).
Safe Working Load of Heavy Duty Trapeze is 250 lbs. (1115 N). DO NOT exceed 250 lb. (1115 N).
A PINCH / SQUEEZE point exists between the head deck and the side rails.
To avoid INJURY keep arms and other appendages away from the openings in the side rails and the upward moving head
deck.

CAUTION
Contact between the floor and the Assist Rail may cause the bed to become UNSTABLE.
An unstable bed may tilt from horizontal and / or drop suddenly causing property DAMAGE or personal INJURY. Before
lowering the bed, ensure the Assist Rail is NOT in the TRANSFER position. INJURY from patient falls may occur even
when operating the side rails as instructed. Place the bed in the lowest position to minimize the risk from falls.
The trapeze bar may damage walls and ceilings when used with the Trendelenburg feature. Invacare recommends removing
the trapeze when using the Trendelenburg function.
DO NOT install an 84 Inch CS Bed kit on a bed that is equipped with the CPR release feature.
DO NOT install an 84 Inch CS Bed kit on a bed that is equipped with the Trendelenburg and Reverse Trendelenburg
feature.
Risk of FALL when Assist Bar is UNLATCHED. Assist Bar may rotate quickly and drop to the next locked position causing
the patient to lose their balance and fall. Ensure the Assist Bar is fully latched in down position after each use. Check that
the Assist Bar is locked before leaving a patient unattended. Never use the Assist Bar as a Rail.

If necessary, the head and foot end board position can be adjusted in order to meet FDA guidelines. Refer to the section
titled, “Install the Mattress Keeper Rod to the Head and Foot Decks” for detailed instructions on adjusting the end board
bracket location.
Part No 1153410
47
Invacare ®CS Series Beds
8 OPTIONS
8.2
Bed Rails and Positioning Devices
The listed bed rails and positioning devices are available:
MODEL
IHCSRLAS
IHCSRLAS-NG
8.3
DESCRIPTION
CS Assist Rails - Set
CS No Guard Assist Rail - Set
IHCSBARS
CS Assist Bar - Set
IHCSTSPD
ThinkSoft® Positioning Device TSPD
IHCSRLPA
68 Inch Rail
IHCSRLAS - 39NG
CS No Guard assist rail for 39 inch wide deck - set
IHCSRLAS - 42NG
CS No Guard assist rail for 42 inch wide deck - set
IHCSBARS - 39
CS assist bar for 39 inch wide deck - set
IHCSBARS - 42
CS assist bar for 42 inch wide deck - set
Other Accessories
The listed items are available as optional accessories:
MODEL
DESCRIPTION
IHCSBEK
4 Inch Extension Kit
IHCSDB
Drainage Bag Holder
IHCSTRP
Standard Trapeze and Mounting Bracket
IHCSTRPHD
IHCSPD
Invacare ®CS Series Beds
Heavy Duty Trapeze and Mounting Bracket
Aftermarket Pan Deck Kit
48
Part No 1153410
8 OPTIONS
8.4
Optional Drainage Bag Holder
8.5
Optional Touch-up Paint
Sherwin-Williams®
5A-58147 00(A)
CODE 82X
WHITE BIRCH
2nd Dimension 5.0 Acrylic Enamel
This product can be purchased at Sherwin Williams Automotive paint branches only.
Part No 1153410
49
Invacare ®CS Series Beds
8 OPTIONS
8.6
Optional Attendant Control Panel Operation
3 Function Pendant
Attendant
Control Panel
Lockout
FIGURE 1 3 Function Pendant
Invacare ®CS Series Beds
50
Part No 1153410
8 OPTIONS
4 Function Pendant
Using the integrated Nurse Call Feature
1.
Locate call cord cable at the head of the bed along with the power cord.
2.
Route cable to nurse call wall outlet and insert call cable plug into socket.

WARNING
Extra cable should be routed and secured to bed to prevent tripping hazards. Otherwise injury may occur.
CAUTION
Route cable and secure to bed avoiding all pinch points. Otherwise damage to the cable and bed will occur.
3.
Coil any extra cable and secure to the bed.
4.
Test Nurse Call by pressing the red first aid button on the hand pendant.

In the event of a power failure or an issue occurs within the electronic system of your Invacare bed, the nurse call button
will be activated, and will not be reset until the electronic system is running properly. Remove the nurse call plug to disable
nurse call signal until service is preformed.
Using the Underbed Light
1.
The underbed light has pre-installed at the foot end of the bed. All cabling has been routed and secured to keep it from getting pinched during
normal operation of the bed.
Part No 1153410
51
Invacare ®CS Series Beds
8 OPTIONS
The underbed light can be turned on by pressing the blue light button on the hand pendant. Press again to turn off.
Attendant
Control Panel
Lockout
Alternate Pendants

All functionality is the
same on the alternate
pendants except where
noted.
Under the
Bed Light
Nurse Call
FIGURE 2 4 Function Pendant
Invacare ®CS Series Beds
52
Part No 1153410
8 OPTIONS
8.7
Optional Trendelenburg and Reverse Trendelenburg Attendant Control Panel

CAUTION
Use of Trendelenburg or Reverse Trendelenburg feature may not be appropriate for certain patients. Trendelenburg and
Reverse Trendelenburg should only be used on the advice of a medical practitioner.
DO NOT install a CS Bed Extender on a bed that is equipped with the Trendelenburg and Reverse Trendelenburg feature.
Under
Bed Light
Nurse
Call
FIGURE 3 Optional Trendelenburg and Reverse Trendelenburg Attendant Control Panel
Part No 1153410
53
Invacare ®CS Series Beds
8 OPTIONS
8.8
Pendant HI/LO Lock Out - Optional

When in the “OFF” position, the HI/LO function on the pendant will NOT operate. When in the “ON” position, all
pendant functions will operate normally. The head function and knee-foot function on the pendant remains operational
whether the lock out is activated or deactivated.
HI/LO
Lockout
Attendant Control Lockout
(at foot end of the bed)
FIGURE 4 Pendant HI/LO Lock Out - Optional
Invacare ®CS Series Beds
54
Part No 1153410
8 OPTIONS
8.9
Optional Cardiopulmonary Resuscitation (CPR) Release

CAUTION
Activation of the CPR release may cause attendant or resident injury. Use with Caution.
Use the CPR release only for emergency situations. This function will rapidly bring the head deck to a flat position. Twoperson operation is recommended; one person to release the head deck, and another to hold and gently guide the head
deck down.
DO NOT install a CS Bed Extender on a bed that is equipped with the CPR release feature.
PINCH-POINT between rail and floor is created when lowering bed to the lowest position.
Keep feet clear of bed rail when lowering bed.
Close supervision is necessary when this product is used by or near children or people with disabilities. DO NOT let any
individual underneath the bed or in between the raised bed frame components at anytime.
Using the CPR Release
When using the CPR Release function, it is recommended to use two people; one person to release the head deck at the foot end of the bed and
another person to gently guide the head deck to a horizontal position.
Additional Means to Lower the Back Rest in an Emergency
The clevis pin and retaining clip can be removed from the connection between the head actuator and head deck section to lower it. The head deck
must be supported while removing the pin and lowering the head deck.
Part No 1153410
55
Invacare ®CS Series Beds
8 OPTIONS
1.
CPR handle is at the foot of the bed. 2. Grip the CPR handle (at the foot end 3.
of bed ).
A second person is recommended
to gently lower the head deck.
Foot end not shown for clarity.
Squeeze the CPR handle to drop
the head deck.
Rapid Action
4.
Once the CPR handle is squeezed,
the head deck will drop rapidly.
Invacare ®CS Series Beds
56
Part No 1153410
8 OPTIONS
8.10 Optional 39 Inch and 42 Inch Wide Decks


WARNING
Possible patient ENTRAPMENT Hazard if using non-specified mattress on a wide bed. Mattress must fit snugly between
appropriate mattress keepers and properly sized head and foot ends that are designed for use on wide beds. Use only a
mattress of recommended specifications with this bed. DO NOT use a mattress extension pad. Refer to Technical Data on
page 23.
The following bed options are not compatible with the 39 inch or 42 inch wide bed deck: 68 inch rail.
The CS bed is available with wider decks for resident comfort. Both 39 inch wide deck and 42 inch wide decks are factory installed options.
39 in or 42 in
Nominal
FIGURE 5 Optional 39 Inch and 42 Inch Wide Decks
Part No 1153410
57
Invacare ®CS Series Beds
8 OPTIONS
8.11 Adjustable Width Bed Model CS9FX600


WARNING
Possible patient ENTRAPMENT Hazard if using non-specified mattress on an adjustable bed. Mattress must fit snugly
between appropriate mattress keepers and properly sized head and foot ends that are designed for use on wide beds. Use
only a mattress of recommended specifications with this bed. DO NOT use a mattress extension pad. Refer to the Bed
Specification section in this manual.
The following bed options are not compatible with the CS9FX600: 68 inch rail.
Adjusting the CS9FX600 Bed Width

All eight adjustable deck wings must be adjusted to the same width. Ensure the appropriate bed and head board settings are
used as described in this procedure.
The CS9FX600 has eight adjustable deck wings which can be adjusted to 36 in, 39 in or 42 in. The locations of the wings and adjustment knobs are
shown in FIGURE 6.
Invacare ®CS Series Beds
58
Part No 1153410
8 OPTIONS
Underside of Bed
Adjustable Head Section
Adjustment
Knobs
Adjustable Seat
Section
Adjustment Knob
Adjustable Thigh
Section
Adjustment Knob
Adjustable Foot Section
Adjustment Knob
Head End
Foot End
Adjustment
Adjustment Knob
Adjustment Knob
Knobs
Adjustable Head Section
Adjustable Seat
Adjustable Thigh
Section
Section
Adjustment Knob
Adjustable Foot Section
FIGURE 6 Adjustable deck wings, knobs and snap buttons
Part No 1153410
59
Invacare ®CS Series Beds
8 OPTIONS
36 in Width
Side View
Adjustable
Deck
Wing
36 in Adjustment
Hole
Adjustment
Knob
Snap Button
Top Bed Deck View
Invacare ®CS Series Beds
39 in Width
Side View
Adjustable
Deck
Wing
39 in Adjustment Hole
42 in Width
Side View
Adjustable
Deck Wing
42 in
Adjustment
Hole
Adjustment
Knob
Adjustment
Knob
Snap Button
Top Bed Deck View
60
Snap Button
Top Bed Deck View
Part No 1153410
8 OPTIONS
1.
Loosen the knob securing the adjustable deck wing.
2.
Depress the snap button
3.
Slide the adjustable deck wing in or out to the desired position.
4.
Ensure the snap button snaps into the appropriate adjustment hole.
5.
Tighten the knob to secure the adjustable deck wing.
6.
Adjust the head board width. Refer to Adjusting the Head Board Width for CS9FX600 on page 62.
7.
Repeat STEPS 1 to 6 for each section until they are all adjusted to the same width.
Part No 1153410
61
Invacare ®CS Series Beds
8 OPTIONS
Adjusting the Head Board Width for CS9FX600
Bed end model IHBEADJ is intended for use on bed model CS9FX600. The head board is adjustable and ships in the position for a 36 in wide bed.
Right Board
Wing
Left Board
Wing
42 in 39 in
36 in
42 in 39 in
36 in
36 in
39 in
39 in 42 in
36 in
42 in
Center
Section
Knobs
1.
Firmly grasp one of the board wings.
2.
While holding the board wing, remove the knobs securing that wings to the center section.
3.
Move the board wing until the mounting holes line up with the desired adjustment holes in the center section.
4.
Install the knobs to secure the board wing in the desired position. Tighten securely
5.
Repeat STEPS 1-4 for the remaining board wing.
Invacare ®CS Series Beds
62
Part No 1153410
9 MAINTENANCE
9 Maintenance
9.1
Cleaning Instructions

CAUTION
Equipment or property DAMAGE or resident INJURY may occur during maintenance.
1.
Unplug product before washing.
2.
Make sure all electrical parts (motors, control box and pendant) are not damaged and that all connection ports are plugged. DO NOT allow
liquids to enter electrical components.
3.
Disinfect and wash all components. DO NOT submerge the bed frame or electrical parts.
4.
DO NOT power wash or steam-clean. Use household water pressure only.
5.
Rinse thoroughly with water (maximum temperature 110°F or 43°C). DO NOT use solvents, bleach, alcohol, petroleum products, caustic
agents, or highly alkaline or acidic agents to clean the bed.
6.
Retract each actuator to the minimum stroke length before washing to avoid degreasing the piston rod.
7.
Dry all components before storing.
Part No 1153410
63
Invacare ®CS Series Beds
9 MAINTENANCE
9.2
Annual Maintenance Check

•
•
•
•
•
•
•
•
•
•
•
9.3
•
9.4
•
9.5
•
WARNING
Failure to maintain your bed may reduce product life and increase unplanned maintenance.
When evaluating the condition of rail attachments it is necessary to consider all aspects of the bed-rail system, including
consideration of the rails, mattress, and bed systems. Refer to the Hospital Bed System Dimensional and Assessment
Guidance to Reduce Entrapment published by the U.S. Department of Health and Human Services Food and Drug
Administration.
Inspect the covering of the bed’s control panel and the patient control panel to assure that the covering is not cracked or damaged.
Inspect for damaged or loose wiring. Have a qualified technician replace any frayed or damaged cords.
Inspect for secure grounding.
Inspect rail latches. Ensure that all rails engage and lock as specified.
Inspect rails for wear and damage and replace as required.
Lubricate rail pivot points as needed with white lithium grease.
Inspect bed, rails, Assist Rails or Assist Bars for the presence of tubing end caps and replace as required.
Tighten, adjust or replace any parts or bolts etc. that are loose or show signs of wear.
Lubricate all mechanical hinge points, bushings, and surface contact points with white lithium grease.
Inspect for wear on clevis pins and hitch pins and replace if worn or missing.
Inspect the rails for noticeable scratches and chips. Use a matching enamel touch up paint to retouch if necessary. (Refer to Options for paint
specification).
Quarterly Maintenance Check
Unplug bed from wall outlet and verify battery function, if equipped. Battery may be built-in or portable.
Environmental Conditions for Storage and Transport
Store and/or transport the bed in a clean and dry environment with an ambient temperature range between 10° and 50° Celsius (0° to 125° F).
Environmental Conditions for Operation
Bring the bed to a Safe Operating Temperature between 5° and 40° Celsius (41° and 100° F) before operating the bed.
Invacare ®CS Series Beds
64
Part No 1153410
10 TROUBLESHOOTING
10 Troubleshooting

WARNING
Read all general guidelines, warnings and cautions before performing any repair/maintenance on the bed. All repair and
maintenance on the bed should be performed by a qualified technician.
Unplug the power cord from its power source before performing any maintenance on the electric bed. DO NOT unplug
the power cord from the control box. Damage to cord will result.
EFFECT
Bed does not stay in
place
POSSIBLE CAUSE
Floor lock not engaged.
Insufficient static friction
between floor lock foot
bumper and floor.
Floor lock not functioning.
VERIFICATION
Green plunger on floor lock post is
visible.
Floor surface is slippery and/or
foreign membrane between bumper
and floor.
Floor lock is stuck in one position.
Bed is not level
Hi/Lo actuators are unevenly
extended
Bed deck is not parallel with floor
Actuator not working.
System Fault
Needs Reset
Flashing LEDs on ACP, Bed function
will not operate. The control box
may beep when pendant function is
pressed.
Part No 1153410
65
CORRECTIVE ACTION
Activate floor lock - green plunger should NOT be
visible.
Clean the surrounding floor and remove loose
material under the bed.
Contact Invacare Continuing Care Service
Department 1-800-668-2337.
Raise bed to highest position
or
Lower bed to lowest position
To Reset - hold the pendant bed up and bed down
buttons for 5+ seconds. The bed will beep and stop
beeping when reset is complete. Then press the bed
up button. If the bed beeps, the actuators are out of
sync. Continue rising to the highest position to
synchronize the actuators.
Invacare ®CS Series Beds
10 TROUBLESHOOTING
EFFECT
Actuator not working.
POSSIBLE CAUSE
HI/LO lock-out is on.
Loose wire connections.
Faulty actuator.
Invacare ®CS Series Beds
VERIFICATION
For non-openbus (CS3, CS5) - A
Lockout box (a square black box)
with a toggle switch. When the
switch is towards "ON" side, the
HILO on the hand pendant will not
function. There is no LED light.
For openbus beds (CS7, CS9,
CS9FX600) - The lockout box (a
flatter rectangular white box) with a
toggle dome button and LED light.
When the light is on, the HILO on
the hand pendant will not function.
Lockout LED on the Attendant
Control Pad (ACP) is ON.
Check cable connections visually.
Disconnect power supply, swap
cable from unresponsive actuator
with a functional actuator.
Reconnect power and test
functions. Faulty actuator will not
work regardless of the connection
port.
66
CORRECTIVE ACTION
Rotate the lockout dial to the “unlocked” position
(horizontal), or flip switch to OFF.
Toggle-off the individual function lockout (LED should
be OFF)
Connect any loose cable couplings and/or power
supplies.
Contact Invacare Continuing Care Service
Department 1-800-668-2337.
Part No 1153410
10 TROUBLESHOOTING
EFFECT
Actuator not working.
POSSIBLE CAUSE
Faulty hand control pendant.
Bed ends to not fit
properly.
Bent brackets.
Part No 1153410
VERIFICATION
Pendant cable is connected, power
is on, lock-out is off and hand
control pendant does not function.
Disconnect power supply then
replace hand pendant with
functioning unit (from another bed,
if available). Reconnect power and
test.
Visually ensure the brackets are
parallel to the frame.
67
CORRECTIVE ACTION
Contact Invacare Continuing Care Service
Department 1-800-668-2337.
Carefully straighten minor deformations. Call Service
Department to replace significantly bent brackets,
1-800-668-2337.
Invacare ®CS Series Beds
For Customer Service, call 800-668-2337
Invacare Continuing Care, Inc.
A subsidiary of Invacare Corporation.
For more information regarding Invacare continuing Care,
Inc. (ICCI) products, parts, and services, please visit
www.invacare-cc.com or call 800-668-2337
Manufacturing
Location:
994 Hargrieve Road
London, Ontario
Canada
N6E1P5
Invacare Continuing
Care, Inc.
USA and Canada:
One Invacare Way
Elyria, Ohio USA
44036-2125
Part No 1153410
Rev L - 3/12
www.invacare-cc.com
Invacare Australia Pty. Ltd.
1 Lenton Place
North Rocks NSW 2151
Sydney, Australia
011-61-2-8839-5333
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement