Totally Wicked E-Pipe III User manual
Totally Wicked E-Pipe III is a versatile and user-friendly vaping device designed for a satisfying and customizable vaping experience. With its adjustable airflow, it allows you to tailor the vapor density and draw resistance to your preference. The E-Pipe III utilizes replaceable atomizer heads for ease of maintenance and flavor variety. It features a 18350 battery for extended vaping sessions and incorporates multiple protection mechanisms, including atomizer head, low battery, short circuit, and no atomizer detection, ensuring safe and reliable operation.
Advertisement
Advertisement
USER MANUAL
1
2
YOUR
Battery
Cap
18350
Battery
Mouthpiece
Tank
E-Pipe 3
Body
Glass
Section
Atomizer
Head
Tank Base
Airflow
Control Ring
3
4
REMOVING THE MOUTHPIECE
1
2
REMOVING THE TANK
5
6
REMOVING THE ATOMIZER HEAD
1 2
PRIME THE ATOMIZER HEAD
x2
7
8
FILL THE TANK
Max Fill
Ensure an air gap of 2mm remains
REATTACH THE TANK BASE
1 2
9
10
ADJUST AIRFLOW
REATTACH TANK TO BODY
11
12
REATTACH MOUTHPIECE
2
1
INSERT THE BATTERY
2
1
13
VAPING
14
Draw gently but firmly to vape
USING YOUR E-PIPE 3
PRIMING THE ATOMIZER HEAD
It is important to “prime” a new atomizer head before first use.
Failure to do so can damage the atomizer head.
Remove the tank from the E-Pipe 3 body by first removing the mouthpiece, twist and pull to remove. Unscrew the tank at the base. Turn the tank upside down, then unscrew the tank base from the glass section of the tank. Remove the atomizer head by unscrewing, drip a few drops of e-liquid onto the cotton wick through the openings on the sides of the atomizer head, and screw back onto the tank base. Reattach the base back on to the tank then reattach the tank to the E-Pipe 3 body. Finally, reattach the mouthpiece on the E-Pipe 3 body.
Note: After priming a new atomizer head it is recommended to wait 5 minutes before vaping to ensure the atomizer head is fully saturated.
ATOMIZER HEAD LIFESPAN
Atomizer heads do not last forever and need to be periodically replaced.
The lifespan of an atomizer head can vary from several days up to several weeks. Factors affecting lifespan include vaping style, flavour and type of e-liquid. Indications that the atomizer head may require replacement include a slight burnt taste, general loss of vapour production or a reduction in flavour intensity.
15
16
USING YOUR E-PIPE 3
FILLING THE TANK & ADJUSTING THE AIRFLOW
Remove the tank from the E-Pipe 3 body by first removing the mouthpiece, twist and pull to remove. Unscrew and remove the tank assembly from the E-Pipe 3 body. Unscrew the tank base and fill to just below the height of the central air tube as shown in the diagram. Avoid allowing liquid into the central air hole. Screw the tank base into the tank. To adjust the airflow to your personal preference, rotate the airflow control ring located at the bottom of the tank base. The more area exposed, the more open the air draw will be. Screw the tank back on to the
E-Pipe 3 body. Refit the mouthpiece by pushing firmly over the tank, being careful to ensure correct orientation of the alignment tab.
FITTING THE BATTERY
To fit the battery, unscrew the battery cap at the top of the body. Insert the battery into its housing negative side first, push the battery cap down and screw back on. The LEDs will flash 3 times to indicate successful insertion.
USING YOUR E-PIPE 3
VAPING
Draw gently but firmly on the E-Pipe 3 mouthpiece so that the LED lights up.
E-LIQUID LEVEL
To prevent the atomizer head from becoming dry and burning prematurely, ensure the e-liquid level does not drop below the inlet holes on the side of the atomizer head, visible through the glass section of the tank. The mouthpiece must be removed to check e-liquid level.
REPLACING THE ATOMIZER HEAD
Remove the mouthpiece with a slight twist and pull. Unscrew the tank at the base. Turn the tank upside down, then unscrew the tank base from the glass section of the tank. Remove the atomizer head by unscrewing, replace with a new atomizer head. Before fitting a new atomizer head, remember that it will need priming as described in the section “Priming the Atomizer Head”.
Reminder: After priming a new atomizer head it is recommended to wait 5 minutes before vaping to ensure the atomizer head is fully saturated.
17
18
PROTECTIONS
ATOMIZER HEAD PROTECTION
If the E-Pipe 3 fires for more than 10 seconds continuously, the LED will remain lit for 3 seconds and the device will not power or produce any vapour. Let the device sit for 1 minute before vaping to allow normal operation to resume.
LOW BATTERY ALERT
If battery voltage drops below 3.3V, the LED will flash 10 times indicating the device needs charging. Insert a fully charged battery to continue vaping.
SHORT CIRCUIT PROTECTION
If an atomizer short circuit occurs, the LED will flash 4 times, the E-Pipe 3 will not provide power to the atomizer or produce any vapour. Replacing the atomizer head should allow normal operation to resume. To replace the atomizer head follow the steps outlined in “Replacing The Atomizer Head”.
NO ATOMIZER DETECTED PROTECTION
If no atomizer head is detected, the LED will flash 5 times and the E-Pipe 3 will not provide power to the atomizer head or produce any vapour. Ensure the atomizer head is fully screwed into the base of the tank, then fit the tank back onto the
E-Pipe 3 body. If the “No Atomizer” sequence continues, replacing the atomizer head should allow normal operation to resume. Follow the steps outlined in
“Replacing The Atomizer Head”.
CLEANING AND MAINTENANCE
The E-Pipe 3 body and tank connection can be cleaned by wiping down with tissue or a dry cloth. The tank can be cleaned by removing it from the E-Pipe 3 body, unscrewing the tank base from the glass section of the tank then removing the atomizer head. The entire tank and base can now be cleaned under hot running water. Allow the tank to fully dry before refitting the atomizer head into the tank. Reassemble the tank.
Note: Do not attempt to clean the atomizer head with water. Do not submerge the E-Pipe 3 body and battery in water or allow it to get wet.
19
20
SPECIFICATIONS
E-PIPE 3
Dimensions: 172mm x 45mm x 58mm.
Weight: 222g with battery fitted.
Battery capacity: Single 18350
Thread type: Proprietary connection.
Atomizer activation: Automatic.
PRODUCT STORAGE AND BATTERY PRECAUTIONS
• Store the E-Pipe 3 and its accessories away from children whilst not in use.
• Please charge batteries using a good quality charger from a reputable vendor.
• Please dispose of dead batteries in accordance with your country’s appropriate legislation.
• Do not charge the battery in a damp environment, or in temperatures under 0°C or above 45°C.
• Do not use the device in temperatures under -10°C or above 60°C.
• Do not carry batteries in a pocket or bag with other metallic objects.
• Do not attempt to repair a faulty E-Pipe 3 body or its battery as these are sealed units with no serviceable parts. Attempted repairs will void the warranty.
WARRANTY
The E-Pipe 3 kit has a 6 months parts warranty, with the exception of atomizer heads, which are consumable items and covered by “dead on arrival” warranty only. If any parts are found to be faulty within this time please contact our customer service team, whose details are on the back page of this booklet and we will arrange for a replacement. We may require the goods to be returned for further investigation.
KIT CONTENTS
1 X E-Pipe 3
1 X PX 0.7ohm atomizer head (fitted)
1 X PX 0.7ohm atomizer head (spare)
1 X Leather E-Pipe 3 stand
1 X User manual
Spare parts
ADDITIONAL PRODUCT INFORMATION
There are no reported medical side effects with this product. If you believe you experience a side effect, please contact the manufacturer.
21
22
Manufactured in China under the authority of
Pillbox38 (UK) Ltd, Stancliffe Street,
Blackburn, Lancashire, BB2 2QR.
Tel: 01254 692244 www.totallywicked.co.uk

Public link updated
The public link to your chat has been updated.
Advertisement