BZBGEAR BG-UM44-150L-KIT 4X4 4K 18Gbps UHD HDMI/HDBaseT Matrix Switcher Owner Manual
BZBGEAR BG-UM44-150L-KIT is a 4x4 4K 18Gbps UHD HDMI/HDBaseT matrix switcher featuring 2-Way IR/Advance EDID/Downscaling/IP, RS-232 control, and an intuitive front panel OLED display. Connect up to 4 HDMI input devices such as Blu-ray players, gaming consoles, and computers, and distribute the signal to 4 HDMI displays or projectors via either HDMI or HDBaseT outputs - all mirrored simultaneously to HDBaseT category cable outputs. This matrix switcher supports resolutions up to 4K2K@60Hz 4:4:4 with each HDMI output supporting 4K2K to 1080P downscaling independently.
Advertisement
Advertisement
BG-UM44-150L-KIT
4X4 4K 18Gbps UHD HDMI/HDBaseT Matrix Switcher with 2-Way
IR/Advance EDID/Downscaling/IP and RS-232 Control
User Manual
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
2
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
TABLE OF CONTENTS
Operation Controls and Functions
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
3
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Statement
Please read these instructions carefully before connecting, operating, or configuring this product. Please save this manual for future reference.
Safety Precaution
● To prevent damaging this product, avoid heavy pressure, strong vibration, or immersion during transportation, storage, and installation.
● The housing of this product is made of organic materials. Do not expose to any liquid, gas, or solids which may corrode the shell.
● Do not expose the product to rain or moisture.
● Unplug this device during lightning storms
● Clean only with a soft dry microfiber cloth.
● To prevent the risk of electric shock, do not open the case. Installation and maintenance should only be carried out by qualified technicians.
● Do not use the product beyond the specified temperature, humidity, or power supply specifications.
● This product does not contain parts that can be maintained or repaired by users.
Damage caused by dismantling the product without authorization from BZBGEAR is not covered under the warranty policy.
● Installation and use of this product must strictly comply with local electrical safety standards.
● Only use accessories specified by the manufacture
● Product specifications may be subject to technical upgrades without further notice
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
4
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Introduction
The BG-UM44-150L-KIT is an 18Gbps 4x4 HDBaseT(150M) matrix. It features four HDMI inputs and four HDMI outputs which are mirrored to four HDBaseT category cable outputs which run simultaneously. The system can support resolutions up to 4K2K@60Hz 4:4:4 and each HDMI output supports 4K2K to 1080P downscaling independently.
The HDBaseT outputs can extend video transmission distance via Cat 5e/6/7 up to 492ft
(150m) at 1080p and 4K2K up to 394ft (120m). While achieving long distances and high resolutions the BG-UM44-150L also supports a variety of HDR formats such as HDR10+,
Dolby Vision, and HLG for rich colors.
The BG-UM44-150L-KIT can de-embed audio to stereo analog and digital coaxial on the transmitter and 3.5mm stereo on the HDBaseT receivers. HDMI audio pass-through supports up to 7.1CH HD audio in a variety of formats like Dolby TrueHD. The system also supports IR matrixing.
The IR signal is one-to-one control at the matrix end and the IR signal follows HDMI video channels at the HDBaseT receiver end. To simplify installation, the receivers support power over cable (PoC) so no additional power supply is needed. The BG-UM44-150L-KIT provides an intuitive front panel OLED screen and control via physical panel buttons, IR remote, RS-232, LAN, or Web GUI.
Features
● HDMI 2.0b, HDCP 2.2 and HDCP 1.x compliant
● Video resolution up to 4K2K@60Hz (YUV 4:4:4) on all HDMI & HDBaseT ports
● 4 HDMI inputs and 4 HDMI / HDBaseT mirrored outputs
● HDMI ports transmit 18Gbps lossless uncompressed video bandwidth
● 18Gbps lossless compressed HDBaseT signal transmission
● 4K->1080P down scaler for each output port
● HDR, HDR10, HDR10+, Dolby Vision, HLG are supported
● HDBaseT output can extend video transmission distance up to 492ft / 150m for
1080P or 394ft / 120m for 4K2K via a single Cat 5e/6/7 cable
● HDMI audio pass-through up to 7.1CH HD audio (LPCM, Dolby TrueHD and DTS-HD
Master Audio)
● IR matrix
● Audio de-embedding via analog and coax ports
● Advanced EDID management and CEC control
● 24V PoC on all HDBaseT ports
● 1U rack mounted design with front panel OLED display
● Control via front panel buttons, IR remote, RS-232, LAN and Web GUI
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
5
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Packing List
● 1 x 18Gbps 4x4 HDBaseT (150M)
Matrix
● 4 x HDBaseT Receiver
● 1 x Matrix IR Remote
● 1 x 100~240V AC 50/60Hz Power cable
● 1 x RS-232 serial cable (1.5 meters, male to female head)
● 4 x 3-pin Phoenix Connector & 4 x 5-pin
Phoenix Connector
● 5 x IR Blaster cable (1.5 meters)
● 5 x IR Receiver cable (1.5 meters)
● 10 x Mounting Ear (Matrix and Receiver)
● 1x User Manual
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
6
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Specifications
Technical
HDMI Compliance
HDCP Compliance
Video Bandwidth
Video Resolution
Color Space
Color Depth
HDR
HDMI Audio Formats
Coax Audio Formats
Analog Balanced
Audio Formats
Vmax
SNR
THD+N Ratio
Crosstalk
Frequency Response
ESD Protection
Connection
Matrix
HDBaseT Receiver
Mechanical
Housing
Color
Dimensions
Weight
Power Supply
Power Consumption
Operating Temperature
Storage Temperature
Relative Humidity
Resolution / Distance
CAT5e/6/7
Resolution / Cable length
HDMI IN / OUT
HDMI 2.0b
HDCP 2.2 and HDCP 1.x
18Gbps
Up to 4K2K@50/60Hz (4:4:4)
RGB 4:4:4, YCbCr 4:4:4/4:2:2/4:2:0
8-bit, 10-bit, 12-bit (1080p@60Hz) 8-bit (4K2K@60Hz YUV4:4:4)
8-bit,10-bit,12-bit (4K2K@60Hz YCbCr 4:2:2/4:2:0 )
HDR10, HDR10+, Dolby Vision, HLG
LPCM 2.0/2.1/5.1/6.1/7.1, Dolby Digital, Dolby TrueHD, Dolby Digital Plus (DD+), DTS-ES,
DTS HD Master, DTS HD-HRA, DTS-X
PCM 2.0, Dolby Digital / Plus, DTS 2.0/5.1
PCM 2.0 CH
2 Vrms
> 90dB
< 0.1% ( V_max ) 0.001%~0.01% ( V_best )
> 80dB
20Hz~20kHz ±0.5dB
Human-body Model: ±8kV (Air-gap discharge), ±4kV (Contact discharge)
Inputs: 4 x HDMI Type A [19-pin female]
Outputs: 4 x HDMI Type A [19-pin female]
4 × HDBaseT port [RJ45]
4 × Coaxial audio [3.5mm Stereo Mini-jack]
4 × Balanced analog audio [5-pin Phoenix connector]
Controls: 5 x IR IN [3.5mm Stereo Mini-jack]
5 x IR OUT [3.5mm Stereo Mini-jack]
1 × TCP/IP [RJ45]
1 × RS-232 [D-Sub 9]
Input: 1 x HDBT IN [RJ45, 8-pin female]
Outputs: 1 x HDMI Type A [19-pin female]
1 x AUDIO OUT [3.5mm Stereo Mini-jack]
Controls: 1 x IR IN [3.5mm Stereo Mini-jack]
1 x IR OUT [3.5mm Stereo Mini-jack]
1 x RS-232 [3-pin Phoenix connector]
1 x SERVICE [Mini-USB, Update port]
Metal Enclosure
Black
Matrix: 440mm (W) × 200mm (D) × 44.5mm (H)
Receiver: 140mm (W) x 65mm (W) x 18mm (W)
Matrix: 3.1Kg, Receiver: 155g
AC 100 - 240V 50/60Hz
60W (Max)
0°C ~ 40°C / 32°F ~ 104°F
-20°C ~ 60°C / -4°F ~ 140°F
20~90% RH (non-condensing)
4K60 -
Feet / Meters
16ft / 5M
4K60 - Feet / Meters
492ft / 150M
4K30 -
Feet / Meters
32ft / 10M
1080P60 -
Feet / Meters
50ft / 15M
The use of “Premium High-Speed HDMI” cables is highly recommended.
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
7
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Operation Controls and Functions
Matrix Panel
Front Panel
5
6
7
NO.
1
2
3
4
Name
LED screen
Power LED
OUTPUT / INPUT buttons
MENU / ENTER / UP /
DOWN
POWER button
IR Window
LOCK button
Function Description
Display matrix switching status, input / output port, EDID, Baud rate, and IP Address.
The LED will illuminate green when the unit is working normally and red when the unit is in standby.
Press an output button (1~4) first and then press an input button (1~4) to select the corresponding input source for the output port.
① EDID setting : On the initial OLED display screen, press the “MENU” button to enter the menu and then Enter on “Select EDID” interface, press “UP/DOWN” button to select the required EDID and press the “ENTER” button to enter “Copy to Input.” Press the “UP/DOWN” button to select the input port you need to set, and press “ENTER” again to confirm.
② Baud rate setting : On the initial OLED display screen, press “MENU” button twice to enter
“SELECT BAUD” interface, and press “UP/DOWN” button to select the required Baud rate, finally press the “ENTER” button to confirm the setting.
③ IP Address Check : On the initial OLED display screen, press “MENU” button three times to enter the IP interface and check the current IP address, then press “UP/DOWN” button to switch DHCP ON/OFF, finally press the “ENTER” button to confirm the setting.
Pressing the “MENU” button again will return to the initial OLED display status.
Press and hold the POWER button for 3 seconds to enter the standby mode, then press the button again to wake up the device.
IR receiver window: it only receives the IR remote signal from this product.
Press the LOCK button to lock front panel buttons (Except the power button); Press the button again to unlock.
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
8
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Rear Panel
2
3
4
5
6
7
No.
1
8
Name
IR IN (1/2/3/4/ ALL) ports
IR OUT (1/2/3/4/
ALL) ports
AUDIO OUT (1-4) ports
Connect to the IR receiver cable, the IR receive signal will be sent to the “IR OUT” port of the
HDBaseT receiver.
Function Description
Connect to the IR blaster cable, the IR emit signal will be from the “IR IN” port of the
HDBaseT receiver.
4 groups of coaxial and balanced analog audio mirrored output ports. AUDIO OUT (1-4) follows the video output of OUTPUT (1-4) ports.
Connect the housing to the ground.
GND
POWER input
Power port: Connect to 100~240V AC 50/60Hz power cable.
Power switch: Press the switch to turn on/off the power.
OUTPUT (1-4) ports
HDMI output ports: connect to a HDMI display device such as a TV or monitor.
HDBT mirrored output ports: connect to HDBaseT receiver via CAT cable.
INPUT (1-4) ports HDMI input ports: connect to a HDMI source device such as BluRay Player.
CONTROL ports
TCP/IP: Connect to an active Ethernet link with an RJ45 cable for TCP/IP control.
RS-232: Command control port. Connect to a PC or control system with a D-Sub 9-pin cable to control the matrix.
Data Signal
Indicator Lamp
Connection Signal
Indicator Lamp
● Solid: HDMI signal with HDCP.
● Flashing: HDMI signal without HDCP.
● Dark: No HDMI signal.
● Solid: Matrix and HDBaseT Receiver are in good connection status.
● Flashing: Matrix and HDBaseT
Receiver are in poor connection status.
● Dark: Matrix and HDBaseT Receiver are not connected.
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
9
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
HDBaseT Receiver Panel
7
8
9
10
No.
Name Function Description
1 Power LED Red LED will be on when the receiver is powered on.
2 SERVICE port Firmware update port.
3
4
5
6
11
DC 24V
HDBT IN
Connection
Signal Indicator lamp
DC 24V/1A power supply input port.
Note: The Matrix supports PoC functionality which means that the receiver does not need a power supply.
RJ45 connector for connecting the HDBT OUTPUT port of Matrix with a CAT cable.
▪
▪
▪
Solid: Matrix and Receiver are in good connection status.
Flashing: Matrix and Receiver are in poor connection status.
Dark: Matrix and Receiver are not connected.
Data Signal
Indicator
▪ Solid: HDMI signal with HDCP.
▪ Flashing: HDMI signal without HDCP.
▪ Dark: No HDMI signal.
HDMI OUT HDMI output port: connect to HDMI display device such as TV or monitor.
AUDIO OUT Analog audio output port: the audio is extracted from the HDMI signal.
IR IN Connect to the IR receiver cable, the IR receive signal will be sent to the “IR OUT” port of the matrix.
IR OUT
RS-232
Connect to the IR blaster cable, the IR signal will be from the “IR IN” port of the matrix.
Connect to a PC or control system with a 3-pin phoenix connector cable to transmit commands between the matrix and HDBaseT receiver.
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
10
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
IR Remote
1.
Power on or Standby : Power on the Matrix or set it to standby mode.
2.
Output 1 : Press 1\2\3\4 button to select input source to
HDMI OUTPUT 1.
3.
Output 2 : Press 1\2\3\4 button to select input source to
HDMI OUTPUT 2.
4.
Output 3 : Press 1\2\3\4 button to select input source to
HDMI OUTPUT 3.
5.
Output 4 : Press 1\2\3\4 button to select input source to
HDMI OUTPUT 4.
Select the last ◀ or next ▶ input source button.
IR Control System
The BG-UM44-150L-KIT is not only a matrix switch but also an extender that supports bi-directional IR control. When the matrix is connected to a HDBaseT receiver through a Cat
5e/6/7 cable, you can control the remote display device (HDBaseT) or input source device
(matrix) through an IR signal transmission. NOTE: The IR signal transmission method is different from matrix (local) to HDBaseT receiver (remote) and from HDBaseT receiver
(remote) to matrix (local).
At the matrix (local end): the IR signal is one-to-one transmission. For example, the IR IN 1 port signal of the matrix will emit to the IR OUT port of the HDBaseT Receiver 1, and the IR
IN 3 port of the matrix will emit a signal to the IR OUT port of the HDBaseT Receiver 3. It does not follow the video switch/change. The IR IN ALL port of the matrix will emit to all IR
OUT ports of HDBaseT receivers simultaneously. Please see the following connection diagram.
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
11
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
At HDBaseT Receiver (Remote end): IR signal follows video switch/change.
For example, the HDMI output signal on the HDBaseT Receiver 1 is from the HDMI
INPUT 2 port, so the IR input signal of the HDBaseT Receiver 1 will emit to IR OUT 2 of the matrix. The HDMI output signal on the HDBaseT Receiver 3 is from the HDMI INPUT
4 port. Then, the IR input signal of the HDBaseT Receiver 3 will emit to IR OUT 4 of the matrix etc. Any HDBaseT receiver’s IR IN signal can output from the IR OUT ALL port of the matrix and the IR OUT ALL signal of the matrix depends on your IR remote source device. Please see the following connection diagram.
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
12
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
IR Cables
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
13
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
EDID Management
This BG-UM44-150L-KIT has 21 factory defined EDID settings, 2 user-defined EDID modes and 8 copy EDID modes. You can select a defined EDID mode or copy EDID mode through the on-panel buttons, RS-232 control, or web interface.
On-panel button operation: On main OLED display screen, press the “MENU” button to enter the EDID setting interface, press “UP/DOWN” button to select the required EDID, and press the “ENTER” button to enter “Copy to Input:” interface. Then press the “UP/DOWN” button to select the input port you need to set, and press “ENTER” again to confirm.
RS-232 control operation: Connect the matrix to a PC with a serial cable, then open a serial command tool on the PC to send ASCII command “s edid in x from z!” to set EDID.
For details, please refer to “EDID Setting” in the ASCII command list in Section 11 “RS-232
Control Commands”.
Web Interface: Please check EDID management in the “Input Setting” in section 10 “Web
GUI User Guide.”
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
14
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
EDID Settings:
12
13
14
15
8
9
10
11
EDID Mode
1
2
3
6
7
4
5
20
21
22
23
16
17
18
19
24~27
28~31
1080p, Stereo Audio 2.0
EDID Description
1080p, Dolby/DTS 5.1
1080p, HD Audio 7.1
1080i, Stereo Audio 2.0
1080i, Dolby/DTS 5.1
1080i, HD Audio 7.1
3D, Stereo Audio 2.0
3D, Dolby/DTS 5.1
3D, HD Audio 7.1
4K2K30_444, Stereo Audio 2.0
4K2K30_444, Dolby/DTS 5.1
4K2K30_444, HD Audio 7.1
4K2K60_420, Stereo Audio 2.0
4K2K60_420, Dolby/DTS 5.1
4K2K60_420, HD Audio 7.1
4K2K60_444, Stereo Audio 2.0
4K2K60_444, Dolby/DTS 5.1
4K2K60_444, HD Audio 7.1
4K2K60, Stereo Audio 2.0 HDR
4K2K60, Dolby/DTS 5.1 HDR
4K2K60, HD Audio 7.1HDR
User defined 1
User defined 2
Copy from HDMI OUTPUT 1~4
Copy from HDBT OUTPUT 1~4
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
15
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Web GUI User Guide
The matrix can be controlled through a web interface and operation is shown below.
Step 1 : Get the current IP Address.
The default IP address is 192.168.1.100. You can get the current matrix IP address in two ways:
1.
You can get the IP address using the front panel buttons. On the initial OLED display, press the “MENU” button three times to enter the IP interface and check the current IP address.
2.
You can get the IP address via RS-232 control. Send the ASCII command “ r ipconfig!” through a Serial Command tool, then you’ll get the feedback information as shown below:
IP: 192.168.62.109 in the above figure is the current matrix IP address (the IP address is variable depending on network configuration).
For a list of RS-232 controls, please refer to section 11. RS-232 Control Commands.
Step 2 : Connect the TCP/IP port of the matrix to a PC with an ethernet cable (as shown in the following figure) and set the IP address of the PC to be in the same network as the matrix.
The computer must be on the same subnet as the matrix to connect successfully. The device will not be accessible otherwise. The units default IP address is 192.168.1.100, therefore the computer must be connected to the 192.168.1.x subnet.
To connect to the matrix, open the “Local Area Connection Properties” on the computer.
For Windows users right-click on the internet connection in the lower right corner of the desktop.
Select “ Open Network & Internet Settings ”.
Select “ Change Adapter Options ”.
Right-click on your connection (Wi-Fi or Ethernet) and select “ Properties ”.
Select “ Internet protocol version 4 (TCP/IPv4) ” as shown below and click “ Properties ”.
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
16
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Click on the bubble for “ Use the following IP address ”
In the IP address field enter a non-conflicting IP address on the same subnet as the camera. If there is another device with the same IP address you will not be able to connect.
In the Subnet mask field enter 255.255.255.0
In the Default gateway field type 192.168.1.1
You can leave the DNS fields blank.
Click OK to apply your settings.
Step 3 : Input the current IP address of Matrix into your browser on the PC to enter the web interface.
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
17
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
After entering the IP address of the unit in the browser the Login page will appear as shown below:
Select the Username from the list and enter the password. The default passwords are:
Username User Admin
Password user admin
After entering the password, click the “LOGIN” button and the following Status page will appear.
Status Page
The “Status” page provides basic information about the product such as model, installed firmware version, and the network information of the device.
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
18
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Video Page
1.
Output : The current device’s OUTPUT port.
2.
Input : You can click the drop-down menu to select a signal source for the corresponding OUTPUT port .
3.
Presets Name : You can name the current scene with a maximum length of 12 characters.
4.
Presets Set : You can restore the last saved audio-video matrix settings.
5.
Presets Save : You can save audio-video matrix switching settings.
6.
Presets Clear : You can clear the saved audio-video matrix switching settings.
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
19
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Input Page
1.
Inputs : Input channel of the device.
2.
Active : It indicates whether the channel is connected to a signal source.
3.
Name : The input channel’s name. You can modify it by entering the corresponding name (max length: 12 characters) in the input box.
4.
EDID : You can set the current channel’s EDID.
The specific operation are as follows:
Set EDID for User
Click the “Browse” button, then select the bin file. If you select the wrong EDID file, there will be a prompt, as shown in the following figure:
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
20
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Make sure to select the correct file, then you can check the name of the selected file. Select
“User 1” or “User 2”, then click “Upload”. After successful setting, it will prompt as follows:
Download the EDID File for the Corresponding Input Channel
Click the drop-down box of “Select EDID File” to select the corresponding input channel.
Then click “Download” to download the corresponding EDID file.
Output Page
1.
Outputs : Output channel of the device.
2.
Name : The current output channel’s name. You can modify it by entering the corresponding name (max length: 12 characters) in the input box.
3.
Type : The current output channel’s type (HDMI or HDBT).
4.
Cable : It indicates the connection status of output ports. When the output port is connected to the display, it shows green, otherwise, it shows gray.
5.
Scaler Mode : Set the current output resolution mode.
6.
Stream : Turn on/off the output stream.
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
21
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
CEC Page
1.
Input Control : You can control the operation of each input source by pressing the icons on the page. (You can control multiple inputs simultaneously.)
2.
Output Control : You can control the operation of each display, such as power on/off, volume +/-, active source switching. (You can control multiple outputs simultaneously.)
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
22
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Network Page
Set the Default Network
Click “Set Network Defaults” button, there will be a prompt, as shown in the following figure:
Click “OK” to search the IP Address again, as shown in the following figure:
After the search is completed, it will switch to the login page with the default network settings.
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
23
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Modify User Password
Click the “User” button, enter the correct old password, new password, and confirm the new password, then click “Save.” After successful modification, there will be a prompt, as shown in the following figure:
Note: Input rules for changing passwords:
1. The password can’t be empty.
2. The new password can’t be the same as the old password.
3. The new password and confirm password must be the same.
Modify Network Setting
Modify the Mode/IP Address/Gateway/Subnet Mask/Telnet Port as required, click “Save” to save the settings.
After modification, if the Mode is set to “Static”, it will switch to the corresponding IP
Address; if the Mode is “DHCP”, it will automatically search and switch to the IP Address assigned by the router.
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
24
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
System Page
1.
Panel Lock : Click to lock/unlock panel buttons. “On” indicates that panel buttons are unavailable; “Off” indicates panel buttons are available.
2.
Beep : Click to turn on/off the beep.
3.
LCD : You can turn on/off the LCD, and set the turn-on time (15s/30s/60s).
4.
Serial Baud Rate : Click the value to set the Serial Baud Rate.
5.
Firmware Update : Click “Browse” to select the update file, then click “Update” to complete firmware update.
6.
Factory Reset : You can reset the machine to factory defaults by clicking “Reset”.
7.
Reboot : You can reboot the machine by clicking “Reboot”.
Note : After reset/reboot, it will switch to the login page.
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
25
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
RS-232 Control Commands
The product supports RS-232 control. You will need a serial cable with RS-232 male head and DB9 transfer USB male head. The RS-232 head of the serial cable is connected to the
RS-232 control port with DB 9 at the rear of the Matrix, and the USB head of the serial cable is connected to a PC. The connection method is as follows:
RS232
Then, open a Serial Command tool on the PC to send ASCII commands to control the
Matrix. The ASCII command list about the product is shown as below.
ASCII Command
Serial port protocol. Baud rate: 115200, Data bits: 8bit, Stop bits:1, Check bit: 0 x - Parameter 1 y - Parameter 2
! - Delimiter
Command
Code
Power s power z!
r power!
s reboot!
Function Description
Power on/off the device,z=0~1 (z=0 power off, z=1 power on)
Get current power state
Reboot the device
Example s power 1!
r power!
s reboot!
Feedback
Default
Setting
Power on
System Initializing... Initialization
Finished! FW version x.xx.xx
power on/power off
Reboot...
System Initializing... Initialization
Finished! FW version x.xx.xx
power on
System Setup help!
r type!
r status!
List all commands
Get device model
Get device current status help!
r type!
r status!
r fw version!
r link in x!
r link out y!
Get Firmware version r fw version!
Get the connection status of the x input port , x=0~4(0=all)
Get the connection status of the y output port , y=0~4(0=all) r link in 1!
r link out 1!
HDP-MXB44H150
Get the unit all status: power, beep, lock, in/out connection, video/audio crosspoint, edid, scaler,hdcp, network status
MCU BOOT:Vx.xx.xx
MCU APP :Vx.xx.xx
SUB1 APP :Vx.xx.xx
SUB2 APP :Vx.xx.xx
CPLD APP :Vx.xx.xx
WEB GUI :Vx.xx
hdmi input 1: connect hdmi output 1: connect hdbt output 1: connect
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
26
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Command
Code s reset!
Function Description
Reset to factory defaults
Example s reset!
Feedback
Reset to factory defaults System
Initializing...
Initialization Finished! FW version x.xx.xx
s beep z!
r beep!
s lock z!
Enable/Disable buzzer function, z=0~1(z=0 beep off, z=1 beep on)
Get buzzer state
Lock/Unlock front panel button, z=0~1
(z=0 lock off,z=1 lock on) r lock!
Get panel button lock state s lcd on time z! Set LCD screen remain on time, z=0~4
(0:off, 1:always on, 2:15s, 3:30s, 4:60s) s beep 1!
r beep!
s lock 1!
r lock!
s lcd on time 1!
beep on beep off beep on / beep off panel button lock on panel button lock off panel button lock on/off lcd always on r lcd mode!
Get the backlight status of lcd screen r lcd mode!
s save preset z! Save switch state between all output port and the input port to preset z, z=1~4 lcd always on s save preset 1!
save to preset 1
Default
Setting beep on panel button lock off lcd on 30 seconds s recall preset z! Call saved preset z scenarios, z=1~4 s recall preset 1!
recall from preset 1 s clear preset z! Clear stored preset z scenarios, z=1~4 s clear preset 1!
clear preset 1 r preset z!
s logo1
****************!
Get preset z information, z=1~4
Set the logo name displayed on the first line of LCD screen, the max character is
16 s baud rate xxx! Set the serial port baud rate of RS02 module, z=(115200,57600,
38400,19200,9600,4800) r baud rate!
Get the serial port baud rate of RS02 module r preset 1!
s logo1 Matrix
Swtich!
s baud rate
115200!
r baud rate!
video/audio crosspoint logo1:Matrix Swtich
Baudrate:115200
Baudrate:115200 s id z!
Output Setting s in x av out y!
Set input x to output y , x=1~4 , y=0~4(0=all) r av out y!
Set the control ID of the product, z=000~999 s id 888!
s in 1 av out 2!
Get output y signal status y=0~4(0=all) r av out 0!
s hdmi y stream z!
Set hdmi output y stream on/off, y=0~4(0=all) z=0~1(0:disable,1:enable) id 888 input 1 -> output 2 input 1 -> output 1 input 2 -> output 2 input 3 -> output 3 input 4 -> output 4 s hdmi 1 stream 1!
s hdmi 0 stream 1!
enable hdmi output 1 stream disable hdmi output 1 stream enable hdmi all outputs stream disable hdmi all outputs stream r hdmi 1 stream!
enable hdmi output 1 stream r hdmi y stream! Get hdmi output y stream status, y=0~4(0=all) s hdbt y stream z!
Set hdbt output y stream on/off, y=0~4(0=all) z=0~1(0:disable,1:enable) s hdbt 1 stream 1!
s hdbt 0 stream 1!
enable hdbt output 1 stream disable hdbt output 1 stream enable hdbt all outputs stream disable hdbt all outputs stream r hdbt 1 stream!
enable hdbt output 1 stream r hdbt y stream! Get hdbt output y stream status, y=0~4(0=all) s hdmi y scaler z!
Set hdmi output y port output scaler mode , y=0~4(0=all), z=1~3(1=bypass,2=4k->1080p, 3=Auto) s hdmi 1 scaler 1!
s hdmi 0 scaler 1!
hdmi output 1 set to bypass mode hdmi all outputs set to bypass mode
115200
0 ptp enable enable hdmi all outputs set to bypass mode
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
27
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Command
Code
Function Description r hdmi y scaler! Get hdmi output y port output mode y=0~4(0=all) s hdbt y scaler z! Set hdbt output y port output scaler mode , y=0~4(0=all), z=1~3(1=bypass,2=4k->1080p, 3=Auto)
Example Feedback r hdmi 1 scaler!
s hdbt 1 scaler 1!
s hdbt 0 scaler 1!
hdmi output 1 set to bypass mode hdbt output 1 set to bypass mode hdbt all outputs set to bypass mode r hdbt 1 scaler !
hdbt output 1 set to bypass mode r hdbt y scaler ! Get hdbt output y port output mode y=0~4(0=all)
EDID Setting s edid in x from z!
r edid in x!
Set input x EDID from default EDID z, x=0~4(0=all),z=1~31
1, 1080p,Stereo Audio 2.0
2, 1080p,Dolby/DTS 5.1
3, 1080p,HD Audio 7.1
4, 1080i,Stereo Audio 2.0
5, 1080i,Dolby/DTS 5.1
6, 1080i,HD Audio 7.1
7, 3D,Stereo Audio 2.0
8, 3D,Dolby/DTS 5.1
9, 3D,HD Audio 7.1
10, 4K2K30_444,Stereo Audio 2.0
11, 4K2K30_444,Dolby/DTS 5.1
12, 4K2K30_444,HD Audio 7.1
13, 4K2K60_420,Stereo Audio 2.0
14, 4K2K60_420,Dolby/DTS 5.1
15, 4K2K60_420,HD Audio 7.1
16, 4K2K60_444,Stereo Audio 2.0
17, 4K2K60_444,Dolby/DTS 5.1
18, 4K2K60_444,HD Audio 7.1
19, 4K2K60_444,Stereo Audio 2.0 HDR
20, 4K2K60_444,Dolby/DTS 5.1 HDR
21, 4K2K60_444,HD Audio 7.1 HDR
22, User define1
23, User define2
24~27, copy from hdmi output 1~4
28~31, copy from hdbt output 1~4
Get EDID status of the input x , x=0~4(0=all input) s edid in 1 from 1!
s edid in 0 from 1!
input 1 EDID:1080p, Stereo
Audio 2.0
all inputs EDID:1080p, Stereo
Audio 2.0
r edid in 0!
input1 EDID: 4K2K60_
444,Stereo Audio 2.0 input2
EDID: 4K2K60_ 444,Stereo
Audio 2.0 input3 EDID: 4K2K60_
444,Stereo Audio 2.0 input4
EDID: 4K2K60_ 444,Stereo
Audio 2.0
r edid data hdmi 1! EDID: 00 FF FF FF FF FF FF 00
……… r edid data hdbt 1! EDID: 00 FF FF FF FF FF FF 00
……… r edid data hdmi y!
r edid data hdbt y!
CEC Setting s cec in x on!
Get the EDID data of the hdmi output y port , y=1~4
Get the EDID data of the hdbt output y port , y=1~4 s cec in x off!
set input x power on by CEC, x=0~4(0=all input) set input x power off by CEC, x=0~4(0=all input) s cec in x menu! set input x open menu by CEC, x=0~4(0=all input) s cec in x play! set input x play by CEC, x=0~4(0=all input) s cec in x pause! set input x pause by CEC, x=0~4(0=all input) s cec in 1 on!
s cec in 1 off!
s cec in 1 menu!
s cec in 1 play!
s cec in 1 pause!
input 1 power on input 1 power off input 1 open menu input 1 play operation iInput 1 pause operation
Default
Setting hdbt all outputs set to bypass mode
1080p,
Stereo Audio
2.0
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
28
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Command
Code
Function Description s cec in x stop! set input x stop by CEC, x=0~4(0=all input) s cec in x rew!
set input x rewind by CEC, x=0~4(0=all input) s cec in x mute! set input x volume mute by CEC, x=0~4(0=all input) s cec in x vol-!
set input x volume down by CEC, x=0~4(0=all input) s cec in x vol+! set input x volume up by CEC, x=0~4(0=all input) s cec in x ff!
set input x fast forward by CEC, x=0~4(0=all input)
Example s cec in 1 stop!
s cec in 1 rew!
s cec in 1 mute!
s cec in 1 vol-!
s cec in 1 vol+!
s cec in 1 ff!
Feedback input 1 stop operation input 1 rewind operation input 1 volume mute input 1 volume down input 1 volume up input 1 fast forward operation s cec in x previous!
set input x previous by CEC, x=0~4(0=all input) s cec in x next! set input x next by CEC, x=0~4(0=all input) s cec in 1 previous! input 1 previous operation s cec in 1 next!
input 1 next operation s cec hdmi out y on!
set hdmi output y power on by CEC, y=0~4(0=all hdmi output) hdmi output 1 power on s cec hdbt out y on!
s cec hdmi out y off!
s cec hdbt out y off!
set hdbt output y power on by CEC, y=0~4(0=all hdbt output) set hdmi output y power off by CEC, y=0~4(0=all hdmi output) set hdbt output y power off by CEC, y=0~4(0=all hdbt output) s cec hdmi out 1 on!
s cec hdbt out 1 on!
s cec hdmi out 1 off!
s cec hdbt out 1 off!
hdbt output 1 power on hdmi output 1 power off hdbt output 1 power off s cec hdmi out y mute!
s cec hdbt out y mute!
s cec hdmi out y vol-!
s cec hdbt out y vol-!
set hdmi output y volume mute by CEC, y=0~4(0=all hdmi output) set hdbt output y volume mute by CEC, y=0~4(0=all hdbt output) s cec hdmi out 1 mute!
s cec hdbt out 1 mute!
set hdmi output y volume down by CEC, y=0~4(0=all hdmi output) s cec hdmi out 1 vol-!
set hdbt output y volume down by CEC, y=0~4(0=all hdbt output) s cec hdbt out 1 vol-!
hdmi output 1 volume mute hdbt output 1 volume mute hdmi output 1 volume down hdbt output 1 volume down s cec hdmi out y vol+!
s cec hdbt out y vol+!
set hdmi output y volume up by CEC, y=0~4(0=all hdmi output) set hdbt output y volume up by CEC, y=0~4(0=all hdbt output) s cec hdmi out y active!
set hdmi output y active source by CEC, y=0~4(0=all hdmi output) s cec hdbt out y active!
set hdbt output y active source by CEC, y=0~4(0=all hdbt output)
Network Setting r ipconfig!
Get the Current IP Configuration s cec hdmi out 1 vol+!
s cec hdbt out 1 vol+!
s cec hdmi out 1 active!
s cec hdbt out 1 active!
r ipconfig!
hdmi output 1 volume up hdbt output 1 volume up hdmi output 1 active source hdbt output 1 active source r mac addr!
s ip mode z!
r ip mode!
Get network MAC address
Set network IP mode to static IP or
DHCP, z=0~1 (z=0 Static, z=1 DHCP )
Get network IP mode r mac addr!
s ip mode 0!
r ip mode!
IP Mode: Static IP: 192.168.1.72
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1 TCP/IP port=8000 Telnet port=10
Mac address:
00:1C:91:03:80:01
Mac address:
00:1C:91:03:80:01
Set IP mode:Static (Please use
"s net reboot!" command or repower device to apply new config!)
IP Mode: Static
Default
Setting
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
29
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Command
Code s ip addr xxx.xxx.xxx.xxx!
r ip addr!
s subnet xxx.xxx.xxx.xxx!
r subnet!
s gateway xxx.xxx.xxx.xxx!
Function Description
Set network IP address
Get network IP address
Set network subnet mask
Get network subnet mask
Set network gateway
Example s ip addr
192.168.1.100!
r ip addr!
s subnet
255.255.255.0!
r subnet!
s gateway
192.168.1.1!
Feedback
Set IP address: 192.168.1.100
(Please use "s net reboot!" command or repower device to apply new config!)
DHCP on, Device can't config static address, set DHCP off first.
IP:192.168.1.100
Set subnet Mask address:255.255.255.0 (Please use "s net reboot!" command or repower device to apply new config!) DHCP on, Device can't config subnet mask, set DHCP off first.
Subnet Mask: 255.255.255.0
Set gateway: 192.168.1.1
Please use "s net reboot!" command or repower device to apply new config!
DHCP on, Device can't config gateway, set DHCP off first.
r gateway!
Get network gateway r gateway!
Gateway:192.168.1.1
s tcp/ip port x!
Set network TCP/IP port (x=1~65535) s tcp/ip port 8000! Set TCP/IP port:8000 r tcp/ip port!
Get network TCP/IP port s telnet port x!
Set network telnet port
(x=1~65535) r tcp/ip port!
TCP/IP port:8000 s telnet port 23!
Set Telnet port:23 r telnet port!
s net reboot!
Get network telnet port
Reboot network modules r telnet port!
s net reboot!
Telnet port:23
Network reboot…
IP Mode: Static IP: 192.168.1.72
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1 TCP/IP port=8000 Telnet port=10
Mac address:
00:1C:91:03:80:01 s uart x datalen y!
Set the data length of x hdbt uart, x=0-8, y=1-2, 1:8bit 2:7bit s uart 1 datalen 1! hdbt uart1 data len is 8bit s uart 1 baudrate 1! hdbt uart1 baudrate is 115200 s uart x baudrate y!
Set the baudrate of x hdbt uart , x=0-4, y=1-8, 1: 115200(Default) 2: 57600 3:
56000 4:38400
5:19200 6:14400 7:9600 8:4800 s uart x parity y! Set the Parity of x hdbt uart, x=0-4, y=1-3, 1:none 2:odd 3:even s uart x type z senddata y end!
Send data y from x hdbt uart, z=0 ascii, z=1 hex ,x=0-4 r uart status x!
Get the Status of x hdbt uart , x=0-4 s uart x parity 1!
hdbt uart1 parity is none s uart 1 type 0 senddata abcdefg end!
r uart status 1!
hdbt uart1 data: abcdefg hdbt uart1 baudrate
9600,datalen 8bit, parity none
Default
Setting
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
30
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Application Example
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
31
BZBGEAR BG-UM44-150L-KIT PRODUCT MANUAL
Tech Support
Have technical questions? We may have answered them already!
Please visit BZBGEAR’s support page ( bzbgear.com/support ) for helpful information and tips regarding our products. Here you will find our Knowledge Base
( bzbgear.com/knowledge-base ) with detailed tutorials, quick start guides, and step-by-step troubleshooting instructions. Or explore our YouTube channel, BZB TV
( youtube.com/c/BZBTVchannel ), for help setting up, configuring, and other helpful how-to videos about our gear.
Need more in-depth support? Connect with one of our technical specialists directly:
Phone
1.888.499.9906
Email [email protected]
Live Chat bzbgear.com
Warranty
BZBGEAR Pro AV products and cameras come with a three-year warranty. An extended two-year warranty is available for our cameras upon registration for a total of five years.
For complete warranty information, please visit bzbgear.com/warranty.
For questions, please call 1.888.499.9906 or email [email protected]
.
Mission Statement
BZBGEAR is a breakthrough manufacturer of high-quality, innovative audiovisual equipment ranging from AVoIP, professional broadcasting, conferencing, home theater, to live streaming solutions. We pride ourselves on unparalleled customer support and services. Our team offers system design consultation, and highly reviewed technical support for all the products in our catalog. BZBGEAR delivers quality products designed with users in mind.
Copyright
All the contents in this manual and its copyright are owned by BZBGEAR. No one is allowed to imitate, copy, or translate this manual without BZBGEAR’s permission. This manual contains no guarantee, standpoint expression or other implies in any form. Product specification and information in this manual is for reference only and subject to change without notice.
All rights reserved.
No reproducing is allowed without acknowledgement.
Address: 830 National Drive #140, Sacramento, CA 95834, USA
·
Tel: +1(888)499-9906
·
Email: [email protected]
32

Public link updated
The public link to your chat has been updated.
Advertisement