Advertisement
Advertisement
Jump Starter Battery Pack
FLX13000
Thank you for choosing the FLUXAMP Jump Starter model FLX13000.
Always follow basic safety precautions when using electronics or jump starting a vehicle.
Read all instructions carefully. Please keep this instruction manual for easy reference or you can download an electronic copy at www.fluxamp.com
Learn About Your FLX13000 Jump Starter!
8
1. DC Output: 19V/3.5A
3. Output: 5V/2.1A
4. DC Output: 12V/3A
5. DC Input: 14V/1A
7. Flashlight
8. LED light
9. Jump Start Socket
2
3
4 5
9
7 1
6
Quick Start Guide - Ready, Get Set, Jump Your Vehicle!
Read vehicle owner's manual: The vehicle manufacturer may have specific cautions and instructions about jumping your vehicle of which you should be aware.
If available, you should wear safety glasses and gloves while jumping your vehicle.
Make sure your FLX13000 has at least 3 indicator lights illuminated.
Remove any and all USB and/or charging devices connected to the FLX13000.
Make sure the vehicle battery terminals, jumper cables and
FLX13000 battery pack are free of any moisture.
Turn off ALL electronics in your vehicle (air conditioner, heat, radio, lights, chargers, etc.) to ensure optimal performance of your FLX13000.
Ensure key is in the "OFF" position in the ignition. For smart-key fobs (push-to- start vehicles), make sure the vehicle is completely "OFF" before jump starting.
Check battery terminals for buildup. If buildup is present, try to clean off terminals with a wire brush or a dry cloth. A clean terminal will provide the best conductivity between your clamps,
Do not attach clamps to FLX13000 yet! First, securely attach the black clamp to the vehicle's negative (-) battery terminal, then the red clamp to the vehicle's positive
(+) battery terminal. Make sure the copper teeth of the clamps are making good contact with the battery terminals for an optimal connection.
Securely fasten the clamps into your FLX13000. Check that you have a secure connection between the terminals and clamps, and between the clamps and
FLX13000 (figure 3).
13.
14.
15.
16.
Start your vehicle (figure 4).
a. If after 3 seconds engine does not start, turn key to OFF position.
b. Detach the FLX13000 from the clamps. Wait 60 seconds and then follow steps 11-16. If problems still persist, please see the Troubleshooting section in your FLX13000 Owner's Manual for other possible causes (figure
5).
4
6
You are now able to drive your vehicle. You should be sure to run your vehicle for at least 15 minutes before shutting it off again. If you have engaged the emergency brake, disengage before driving your vehicle.
Operation Guide:
Indicator Lights
The FLX13000 Jump Starter has 5 indicator lights to determine the amount of power in the unit.
•
•
•
Press the on/off switch to activate the lights. The display as below shows the level of power in relation to the number of lights illuminated.
The indicator lights will flash one by one when the unit is charging. A solid light indicates a complete level of charge. For example, when 2 lights are illuminated and a third is blinking, that means the unit is between 40 -60% charged. Once the third light stops blinking the unit is 60% charged.
Charging
100% 80% 60% 40% 20%
When all five light are lit, the unit is fully charged!
Charging the FLX13000 Jump Starter
Your FLX13000 Jump Starter has two options for charging the unit:
1. With the wall plug 2. With the car adaptor in your vehicle
•
•
Simply connect the wall plug or the car adaptor into the 14V/1A input port of the
FLX13000 Jump Starter and start charging!
The unit will fully charge in approximately 4 hours.
Charging a Phone, Tablet or Other USB Devices
The FLX13000 Jump Starter comes with two USB discharging port located at the side of the unit:
•
•
Select appropriate connector and connect it to your smartphone, tablet or USB device you want to charge.
Power on the FLX13000 and start charging the external devices!
Flashlight
The FLX13000 Jump Starter comes with LED flashlight that has a number of different settings:
•
•
Press the button once: the green Indicating
Light to show the battery capacity.
Press the on/off switch for 3 seconds: it shows white LED, white LED as flashlight.
There are 3 modes of LED light that appear in the following order:
1st click: Strobe 2nd click: SOS
3rd click: OFF
• Press the on/off switch for twice quicky: it shows red LED. There are 3 modes of
LED light that appear in the following order:
1st click: Strobe 2nd click: SOS
3rd click: OFF
Jump Starting a Vehicle:
•
•
•
•
Please see the FLX13000 Quick Start Guide for step-by-step procedures on how to jump your vehicle.
Many of us have had the dreaded experience of returning to our vehicles only to find they will not start. Most of the time the culprit is a dead or drained battery for which we needed to call for help or flag down a fellow driver.
By owning a FLX13000 Jump Starter you have everything you need to jump start a vehicle - no need to wait for help to arrive. FLX13000 to the rescue!
We know you're excited, but before jumping your vehicle, please be sure to take some precautionary steps:
Read your vehicle owner's manual first as the manufacturer may have specific steps and precautions that pertain to your vehicle.
Thoroughly follow the FLX13000 Quick Start Guide and review the FLX13000
Owner's Manual.
Remove any and all moisture from your FLX13000 unit and accessories, as well as your vehicle's battery. NEVER attempt to jump start a vehicle when moisture is
•
•
•
•
•
•
Properly identify the vehicle battery's positive and negative terminals before connecting the clamps.
When using the clamps, DO NOT allow the metal teeth of the clamps to touch one another. This will cause a short circuit which could cause a spark and may compromise your clamps.
When using the clamps, DO NOT connect the RED clamp to the vehicle battery's negative (-) terminal, or the BLACK clamp to the vehicle battery's positive (+) terminal. This will cause a reversal of polarity and could compromise your clamps.
When connecting the FLX13000 clamps to the battery terminals, please ensure that you have a secure connection. The copper teeth of the clamp should be securely attached to the metallic portion of the terminal. The better the connection, the easier it will be to start your vehicle.
NOTE: When adjusting the clamps please be sure to first disconnect the FLX13000.
This will prevent the occurrence of minor sparks.
General Guidance: FLX13000 Model to Engine Size
FLX13000 Jump Starters can be used on gas and diesel engines as follows:
Up to 3.5 liter gas engines/2.6 liter diesel engines*
*Engine size is approximate; power requirement will vary for each vehicle.
NOTE: Extreme cold temperatures affect battery performance. If you operate in
Product Service or Missing Parts for Your FLX13000
Any questions about operating or using this new FLX13000 Jump Starter or if parts are missing, please contact FLUXAMP first at www.fluxamp.com
Should this product require factory service or replacements please contact local distributors directly. This will ensure the fastest turn-around time.
•
•
•
•
•
•
•
•
•
•
•
Important Safety Information
WARNING: Read all instructions and warnings prior to using this product. Improper use of this product may result in product damage, excess heat, toxic fumes, fire or explosion, for which FLUXAMP is not responsible.
Always read all instructions carefully before using your FLX13000 Jump Starter.
Do not submerge your FLX13000 Jump Starter in water, or expose it to rain or moisture.
Never open or disassemble your FLX13000 Jump Starter as it will void your warranty.
Do not expose your FLX13000 Jump Starter to fire, intense heat, or flammable liquids.
Only charge the product at temperatures between -4°F (-20°C) to 140°F (60°C)
Keep away from and out of reach of children.
Do not insert foreign objects into ANY inputs or outputs.
Do not use this product where there are flammable fumes, gases, or dust present.
Do not allow the metal teeth of the red clamp to touch the metal teeth of the black clamp when connected to the FLX13000.
Do not connect the black clamp to the vehicle battery's positive (+) terminal when connected to the FLX13000. Do not connect the red clamp to the vehicle battery's
•
•
•
•
•
•
•
Do not expose the FLX13000 to temperatures over +140°F (+60°C) or under -4°F
(-20°C) as this could decrease the performance of your battery.
Do not expose the FLX13000 to temperatures over +140°F (60°C) as this could create a safety hazard.
Always disconnect the jump start cables from the FLX13000 after use and store separately.
Do not crush, puncture, or penetrate the FLX13000 as this poses a safety risk.
In the extremely unlikely event that any corrosive liquid seeps from your FLX13000, discontinue use. If any corrosive liquid comes in contact with your skin or eyes, immediately wash with running water and consult a doctor.
Your FLX13000 must be disposed of properly when it is no longer able to be used.
You need to recycle your lithium-ion battery at a local facility.
If there are any problems with the product or a malfunction occurs during usage,
FAQ's
Q:
A:
Q:
A:
Q:
A:
Q:
A:
Do I need to read my vehicle user's manual before using the FLX13000 Jump Starter to jump start my vehicle?
We recommend that you read your vehicle user's manual before jump starting your vehicle as other precautionary steps may be specified by the vehicle's manufacturer.
Before jump starting my vehicle, what steps do I need to take?
Please refer to the User’s Manual and/or Quick Start Guide. You can also find these documents online at www.fluxamp.com.
What happens if my FLX13000 clamps accidentally touch?
Please read all instructions and safety warnings before Jump starting your vehicle.
Connecting the metal teeth of the clamps would create a short circuit, which could result in a spark and possibly damage your clamps.
What happens if I accidentally connect the FLX13000 clamps to the wrong battery terminals?
Please read all instructions and safety warnings before Jump starting your vehicle.
Connecting the clamps to the wrong terminals could cause a reverse polarity and possibly damage your clamps.
Q:
A:
Q:
A:
Q:
A:
What car can FLX13000 start?
FLX13000 Jump Starters can be used on gas and diesel engines as follows:
Up to 3.5 liter gas engines/2.6 liter diesel engines*
*Engine size is approximate; power requirement will vary for each vehicle.
NOTE: Extreme cold temperatures affect battery performance. If you operate in these conditions for any length of time, consider the next largest FLUXAMP Jump Starter.
How do I turn off my FLX13000 Jump Starter?
The FLX13000 Jump Starter will power off automatically when not in use.
Q:
A:
How do I turn on the flashlight on my FLX13000 Jump Starter?
Press the on/off switch for 3 seconds: it shows white LED, white LED as flashlight.
There are 3 modes of LED light that appear in the following order:
1st click: Strobe 2nd click: SOS
3rd click: OFF
How long does it take to fully charge the FLX13000 Jump Starter?
Approximately 4 hours
Q:
A:
Q:
A:
Q:
A:
Q:
A:
Q:
A:
Q:
A:
Q:
A:
Q:
A:
How many times can the FLX13000 Jump Starter jump a vehicle if the battery is fully charged?
This will vary as every vehicle has different power requirements. A fully charged FLX13000 will provide enough power for several jump-start attempts. Please ensure the FLX13000 shows at least 3 lightsindicator before jump starting your vehicle. Please be sure to charge your FLX13000 after jump starting your vehicle.
How many times can the FLX13000 Jump Starter charge a cell phone, tablet or other portable devices, and how long will it take?
This will vary as all portable devices' batteries have different power requirements and capacities.
How many USB devices can the FLX13000 Jump Starter charge at once?
FLX13000 has 2 x 2.1A USB port , it can charge 2 x iPad at the same time.
What is the lifespan of the FLX13000 Jump Starter?
The FLX13000 Jump Starter can be fully charged and discharged up to 1000 times under ideal conditions. Your FLX13000 will typically last 3-5 years. For proper storage and maintenance:
• Do not expose unit to moisture and rain.
• Do not store unit in extreme temperatures.
• Do not store unit for long periods of time with less than 3 indicator lights showing
charge.
How long will the FLX13000 Jump Starter hold a charge when not in use?
Anywhere from 6-12 months, depending on storage conditions; however, we recommend that you recharge your FLX13000 Jump Starter every 3 months to guarantee successful performance when needed.
Does the FLX13000 Jump Starter come with a warranty?
Yes - please see the back of the User's Manual for warranty information.
Who do I contact If I have a question about my FLX13000?
For further assistance please email [email protected]
How do I property dispose of my Lithium-ion battery?
Lithium-lon batteries should be properly recycled at a local facility.
Troubleshooting
•
•
My car won't start. How do I know the battery is the issue?
While key Is in OFF position, turn on your headlights and interior lights. Turn key to ON position. If the lights dim after you turn key to ON, your battery is weak and needs to be Jumped.
Turn key to ON position. Turn on windshield wipers. If wipers are slower than usual, your battery is weak and needs to be jumped.
I followed the necessary steps but my vehicle is still unable to start. Now what?
After an unsuccessful jump do not attempt again for another 60 seconds so as to not strain
• your FLX13000.
Your FLX13000 does not have enough charge:
Make sure at least 3 lights indicator are lit on the FLX13000 before starting your vehicle. If not charge your FLX13000.
•
•
•
•
•
•
•
Your clamps could be compromised. Detach FLX13000 from clamps. If it still powers on, this means the issue may be within the clamps' safety features (fuse on black clamp, diode on red clamp):
If you connected your clamps to the wrong battery terminals, you could have experienced a reverse polarity and blown the safety diode on your red clamp. To order a new set of clamps, please visit contact the seller.
If your vehicle has drawn too much power from the FLX13000, you could have blown the safety fuse on your black clamp. To order a new set of clamps, please contact the seller.
Your engine is too powerful for your FLX13000.
Our batteries work very hard to supply the power you need, but some engines demand more than your FLX13000 can give. You may want to try the next larger jump starter.
Your battery terminals are dirty:
Build-up on your battery terminals may be hindering conductivity. Make sure your terminals are clean before attaching the clamps. You can use a wire brush or dry cloth to clean your terminals.
There may be a poor connection:
A poor connection between the clamps and the terminals can prevent a successful engine start. Disconnect the FLX13000 from the clamps, then adjust the clamps to ensure the most secure connection. Reconnect the FLX13000 and try again.
Your vehicle battery may not be the issue.
In most instances, a dead battery is preventing an engine start, but sometimes it goes much deeper than that. There may be other functions in your vehicle that aren't working properly, thus preventing a successful engine start. Please refer to your vehicle owner's manual or visit your local service garage to determine what the issue
I accidentally connected my clamps to one another. Have I damaged my FLX13000?
Remove the clamps from the FLX13000 and press the power button. If the indicator lights are still on, you have not damaged your FLX13000.
Connecting the clamps to one another creates a short circuit. You could have blown the safety fuse on your clamp. If so, you will need a new set of clamps. To order a new set of clamps, please visit contact the seller.
•
• I accidentally connected the clamps to the wrong terminals. Have I damaged my FLX13000?
Remove the clamps from the FLX13000 and press the power button. If the indicator lights are still on, you have not damaged your FLX13000.
You could have experienced a reverse polarity and blown the safety diode on your clamp. To order a new set of clamps, please visit www.FLUXAMP. com/contact.
•
•
•
• I connected my portable device to my FLX13000 with a USB, but it will not charge.
After connecting a device to your FLX13000, be sure to power ON the FLX13000.
Make sure the FLX13000 is charged. lf no indicator lights illuminate after powering on the device, charge your FLX13000.
Make sure the USB cable is securely connected to the FLX13000.
You may have a faulty USB cable.
I connected my FLX13000 to the charger, but there are no indicator lights blinking.
•
•
•
Check that the charger is securely attached to the FLX13000 input port.
You may have a faulty outlet. Try plugging your FLX13000 charger into an alternate outlet.
•
•
I am unable to turn on the flashlight.
Make sure your FLX13000 is charged.
Be sure to hold the ON/OFF button for 3 seconds to activate the flashlight.
My FLX13000 will not power on.
•
• Charge your FLX13000. You should eventually see blinking indicator lights once the
FLX13000 has enough charge.
If the automotive devices are ignited when the battery capacity is low, the jump starter could fail to operate due to the inner chip safety protection function been activated. This can be re-activated and reset by charging the device.
Parts List
Description
FLX13000 Jump Starter Unit
Car Charger
2-in-1 USB Charging Cord
Quantity
1
1
1
Description
Wall Charger
User's Manual
Clamp
Spare parts are available for purchase at www.fluxamp.com
Quantity
1
1
1
FLX13000 Technical Specifications
Battery Size: 8000 mAh mAh (milliampere-hour) - lt's simply a measure of battery capacity. The more mAh, the more available power for your device.
Battery Type: High-power Type Lithium-ion
Lithium-ion - It's what makes your rechargeable battery tick (not literally!).
Quality li-ion battery cells provide long battery life and consistent performance.
Volts: 12V
Starting/Peak Current: 200A/400A
Max Input: 14V/1A
Max Output: 5V/2.1 A ×2
"A" (amperage or amps) - lt's the measure of current that runs from the battery pack to your device (output) or from the outlet to the pack (input) - higher "A" means faster charge (input) or discharge (output).
DC Charging Port: 1
Auto OFF: Yes
Indicator Lights: 5
Charging Cycles: up to 1000 times
We are talking full cycles (a full charge + discharge).
Warranty
1-YEAR LIMITED WARRANTY
WHAT THIS WARRANTY COVERS: FLUXAMP sells its products with the intent that they are free of defects In material and workmanship under normal use and service for a period of 1 (one) year from the date of original purchase, except as noted below.
This warranty extends only to consumers and specifically does not extend to Retailers, sellers or their agents or employees. FLUXAMP does not authorize anyone, including, but not limited to, Retailers, the subsequent consumer purchaser of the product from a
Retailer or remote purchasers, to obligate FLUXAMP in any way beyond the terms set forth herein.
This warranty does not cover damage caused by misuse or abuse; accident; altercation to the product; attachment of any unauthorized accessory; improper use of an electrical/power supply that causes malfunction; loss of power; dropped or crushed product; malfunction or damage of an operating part from failure to provide manufacturer's recommended maintenance; tampering with or attempt to modify the product; unauthorized opening of the product; transportation damage; theft; neglect; vandalism; environmental conditions; loss of use during the period the product is at a repair facility or otherwise awaiting parts or repair; or any other conditions whatsoever that are beyond the control of FLUXAMP.
This warranty is effective only if the product is purchased and operated in the country in which the product is purchased. A product that requires modifications or adoption to enable it to operate in any other country than the country for which it was designed, manufactured, approved and/or authorized or repair of products damaged by these modifications is not covered under this warranty.
This warranty does not extend to the purchase of opened, used repaired, repackaged and/or resealed products, Including but not limited to sale of such products on Internet auction sites and/or sales of such products by surplus or bulk resellers. Any and all warranties or guarantees shall immediately cease and terminate as to any products or parts thereof which are repaired, replaced altered or modified, without the prior express and written consent of FLUXAMP.
FLUXAMP shall not In any way be liable to you or any third party for any damages you or any third party may suffer as a result of use, Intended or unintended, or misuse of this product in conjunction with any device, equipment or accessory other than the appropriate device or equipment for which this product is designed. FLUXAMP will not be responsible for any damages you or any third party may suffer as a result of misuse of this product outlined above. If you are responsible for this product's use with any unintended device and damages result from such use, you agree to indemnify FLUX-
AMP for any resulting injuries to any third parties.
WHAT IS THE PERIOD OF WARRANTY COVERAGE: This warranty starts on the date of original purchase and extends for 1 year from that date of original purchase.
WHAT WE WILL DO TO CORRECT DEFECTIVE PRODUCT: If FLUXAMP determines that a returned product has a defect in manufacture or workmanship under normal use,
FLUXAMP will at Its sole discretion, repair or replace the defective part or parts, or if necessary, provide a like or comparable product from its product line. FLUXAMP will repair or replace the defective product free of charge and return the product to the stated consumer's US address only, free of charge. If replacement parts for defective materials are not available, FLUXAMP reserves the right to make comparable product substitutions in lieu of repair or replacement. No refunds will be given. If FLUXAMP determines that the product is not defective, it will return the product to the consumer at the consumer's expense.
To obtain warranty service, contact our customer service specialist:
• Please visit contact the seller
• via online: [email protected]
REMEDIES: The warranty provided herein shall be the sole and exclusive warranty.
There shall be no other warranties express or implied, or any other obligation on the part of the company with respect to products covered by this warranty. FLUXAMP shall have no liability for any incidental, consequential or special damages. In no event shall this warranty require more than the repair or replacement of any part or parts which are
© 2015. All rights reserved. www.fluxamp.com Made In China

Public link updated
The public link to your chat has been updated.
Advertisement