Advertisement
Advertisement
SPECIFICATIONS OUTPUT POWER 30W SUBWOOFER SATELLITE Cine Box 10W 60W MAXIMUM OUT POWER SPEAKER UNIT MSPD-800C 5-1/4" WOOFER 1/2" 2 SATELLITE Instruction Manual DIMENSION 920(W)x200(H)x113(D)(mm) UNIT ACCESSORIES 1PC 1PC REMOTE CONTROL BUTTON-TYPE BATTERY 1 PC(1.5m) RCA(yellow) to RCA(yellow) VIDEO CABLE ЕЕ = 9 5 = D 0x “я RCA(orange) to RCA(orange) COAXIAL CABLE 2RCA to 2RCA CABLE WALL MOUNT BRACKET USER MANUAL O o O o WALL MOUNT GUIDE Due to continuous product development through R and D Note Surround Sound System in one-box specification to change without prior notice. Please read this manual carefully before operating and save it for future reference. -14- MAINTENANCE & TROUBLESHOOTING If the system do not operate correctly, please do the following check up ISSUE CAUSED BY SOLUTION No sound from speaker 1. System does not 1. Check with the power or no power connected with power. plug. 2. The power does not 2. Make sure the power switch on. switch at the back pane is on. No sound effect from speaker | Confirm DVD player is set up Setup the DVD to output when choose DVD/5.1 output | for 5.1 output audio in 5.1 mode Distortion occurred when The sound device has high Turn down the master in high volume level signal output volume of the system Note A: 1) The proper combination of input and output mode (Both the Active Subwoofer and the supply source, i.e CD,MP3,VCD,DVD......) will produce optimize sound quality. Please refer to both Instruction Manual. 2) Some DVD device has high level signal output . When the Master Volume is turn high until the distortion occurs, please turn down the Master Volume to prevent damaged to the speaker unit and amplifier. Note B: When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lighting, etc.) or it is operated incorrectly, it may malfunction. If such a problem occurs, please do the following to reset the system. 1) Set the system to STANDBY mode and turn the POWER on again. 2) If the system is not restored using the previous operation, turn off the MAIN POWER switch, unplug the power cord plug for few minutes and try to on it again. The product has self-protection act when shocked by static electricity, and all functions can be used normally re-start. -13- SYSTEM SETUP CONTENTS 3. DUAL MONO: This option allows you to set the output methods for the left and right audio signals. There are 4 modes: stereo, left sound channel, right sound channel, and mixed sound channel, to be selected according to the AC-3 KRAOKE mode. 4. PROLOGIC: a) MOVIE MODE: This option allows you to set Dolby Pro Logic Il sound mode is movie. | b) MUSIC MODE: This option allows you to set Dolby Pro Logic Il sound mode is music. Safety Precaution 2 с) OFF: Turnoff the Dolby Pro Logic Il sound mode. Description of the Unit 3 a =: (7) => € a =: (7) => CJ | DIGITAL SETUP | DIGITAL SETUP Description ofthe Remote 4 DUAL MONO bo Main Feature 5 MIXMONO = OFF о Connections 6 MEMORY CARDS System Basic Operation 7 Playing MP3 audio and picture files stored on flash memory cards: 1) Turn the system On as usual. System Setup 8 2) Insert your flash memory card containing MP3 audio/JPEG files into the memory card slot. Note: The card only be inserted one way, push it in as far as, it will go until it locks in place. 3) The system will read the information on the card. If the system connected TV, the screen Memory Cards 12 show as following: @ ( | OA | ®( ) Maintenance & Troubleshooting 13 om ||: em ) sc |> Specification 14 E e > >» s ope Playing MP3 audio file Playing JPEG file Playing AVI video file 4) Press the ENTER/PLAY button on the remote control to begin playback. Or press »/ı button on the front panel to begin playback. 5) Press »/ı button on the front panel to pause playback, press it again to resume playback. 6) Press PREV or NEXT button repeatedly during playback to skip to the previous or next track. 7) Press REV or FWD button to fast reverse or fast forward. (Fast forward): FF 2Х=> FF4X=> FF8X=> FF20X=> PLAY (Fast reverse): FR 2X=>FR4X=> FR8X=>FR20X > PLAY 8) Press STOP button to stop playback. 9) Press REPEAT button repeatedly to select one of the following repeat modes: REP ONE => FOLDER REPEAT => REPALL™ PLAY Note: When playing SD/MMC, press the SD/USB button to select USB read mode, press the SD/USB button again to resume the previous mode. -12- -1- SAFETY PRECAUTION SYSTEM SETUP When used in the directed manner, this unit has been designed and manufactured to ensure your 6. CENTER: This option allows you to adjust the center speaker volume large or small and off. personal safety. However, improper use can result in potential electrical shock or fire hazards. 7. REAR: This option allows you to adjust the rear speaker volume large or small and off. Please read all safety and operating instructions carefully before installation and use. Be sure to = г > = р > keep these instructions handy for future reference. Take special note of all warnings listed in these E = El- E u Е - instructions and on the unit. | SPEAKER SETUP | SPEAKER SETUP | SPEAKER SETUP DOWNMIX SUBWOOFER CAUTION ON CENTER DELAY RISK OF ELECTRIC SHOCK OF | DO NOT OPEN The lightning flash with arrowhead symbol within an equilateral is intended to alert the user to the presence of uninsulated dangerous voltage within the product enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Л The exclamation point within an equilateral triangle is intended to alert the user to the m 4 7) © EJ = = @ Ey = "= @ > Ey = presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. |_ SPEAKER SETUP |_ SPEAKER SETUP | SPEAKER SETUP 1. Water and Moisture ---The unit should not be used near water. For example, near a bathtub, REAR DELAY kitchen sink, laundry tub, swimming pool or in a wet basement. FRONT LARGE — 2. Ventilation ---The unit should be situated so that its location or position does not interfere with live ZUR LARGE its proper heat ventilation. For example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air through the ventilation openings. x = 3. Heat ---The unit should be situated away from heat sources such as radiators, heat ducts, stoves | SPEAKER SETUP or appliances (including amplifiers) that generate heat. 4. Power Source---The unit should be connected to a power supply of the type described in the operating instructions or as marked on the unit. 5. Power-cord Protection---Power supply cords should be routed so that they are subject to wear ‘LARGE or abuse. It is always best to have a clear area from where the cord exists the unit to where it is REAR plugged into an AC outlet. 6. Cleaning---The unit should be cleaned only as recommended. See the Maintenance section of this manual for cleaning instructions. Digital Setup 7. Objects and Liquid Entry---Be careful that objects do not fall and liquids are not spilled into any Use [A] [У] [4] [>] buttons to select the highlighted mark to the option to be set, and use openings or vents located on the unit. ENTER/PLAY button to confirm. 8. Attachments---Do not use attachments that are not recommended by the product manufacturer. 9. Lightning and Power Surge Protection---Unplug the unit from the wall outlet and disconnect the 1. OP MODE: antenna or cable system during a lightning storm. This will prevent any damage to the unit. a) LINE OUT: To zip the inputted signals linearly. The volume is low and, therefore, you should a . . : use this option at nighttime. . Overloading Do not overload wall outlets, extension cords, or integral convenience receptacles b) RF REMOD: Volume is high and is suitable for daytime. as this can result in a risk of fire or electric shock. . DYNAMIC RANGE: You can change the zip mode to LINE OUTPUT in order to adjust linear zip = o No 11. Damage Requiring Service---The unit should be serviced by qualified service personnel when: radio and obtain the zip effects for different signals. If you choose FULL, the peak value of A. The power supply cord or plug has been damaged. , audio signal is minimum, and becomes maximum if you choose off. B. Objects have fallen, or liquid has been spilled into the unit. Note: This option is available only when the system is set as "5.1 sound channel". C. The unit has been exposed to rain. D. The unit has been dropped or the enclosure damaged. E. The unit exhibits a marked change in performance or does not operate normally. ши a: A. 12. Antenna---Do not connect an external antenna to the unit (other than that provided). | DIGITAL SETUP | | DIGITAL SETUP 13. Periods of Non-use---If the unit is to be left un-used for an extended period of time, such as a OP MODE LINEOUT — month or longer, the power cord should be unplugged form the unit to prevent damage or corrosion. DYNAMIC RANGE 14. Servicing---The user should not attempt to service the unit beyond those methods described in the user’ s qualified service personnel. SYSTEM SETUP Video Setup Use [A] [W] [«] [»] buttons to select and highlight the option to be set, and use ENTER/PLAY button to confirm. 1. BRIGHTNESS: Press the direction button [a] [w] to move the indicator to set the brightness of video output. 2. CONTRAST: Press the direction button [A ][W]to move the indicator so as to set the contract of video output. 3. HUE: Press the direction button [A] [У] to move the indicator so as to adjust the colors of video output. 4. SATURATION: Press the direction button [4] [У] to move the indicator so as to adjust the saturation of video output. 5. SHARPNESS: Press the direction button [А] [У] to move the indicator so as to adjust the sharpness of video output. |_ VIDEO SETUP | | VIDEO SETUP | VIDEO SETUP BRIGHTNESS = НЕ HUE ne ala o = =] ak) =<) = | VIDEO SETUP | VIDEO SETUP = Es de SHARPNESS Speaker Setup Use [A] [У] [<4] [»] buttons to select and highlight the option to be set, and use ENTER/PLAY button to confirm. — N © > O1 . DOWNMIX: a) LT/RT: you can select this option to decrypt the signal so as to present a vivid theater effect, provided that your DISC contains PRO LOGIC Dolby stereo effect. b) STEREO: at 5.1 sound channel output, the audio outputs to 5 speakers and a sub-woofer. At 2 sound channel output, the audio outputs to left and right speakers. c) VSS(Virtual circumferential sound): if you play a DISC with 5.1 sound channel mechanism, the main amplifier outputs virtual circumferential effect. d) OFF: when select OFF, becomes 5.1 output mode. . SUBWOOFER: there are 2 options: on/off. At ON status, the system checks if there is any super bass inputted. In OFF status, no voice will be outputted. . CENTER DELAY: This option allows you to set intermission delay time. Note: available only at 5.1 sound channel mode. . REAR DELAY: This option allows you to adjust the setup of circumferential delay time. Note: available only at 5.1 sound channel mode. . FRONT: This option allows you to adjust the front speaker volume large or small. -10- DESCRIPTION OF THE UNIT FRONT VIEW 5559 со sO > Ko} о хо T [e] a x о fo} 2026202 08020202086; 20 00 E — р ОО 222 2 6 8 3 5 7 9 BOTTOM VIEW . LED Display . Standby button . Mute button . Input select button USB Connector . SD/MMC/MS card reader . Play/Pause button . Master volume up button . Master volume down button 10. AC Cord 11. Main Power Switch 22 12. Fuse 13. Video Output Connector 14. Subwoofer Output Connector 15. Aux Input Connector 16. TV Input Connector 17. Coaxial1 Input Connector 18. Optical1 Input Connector 19. Optical2 Input Connector 20. Subwoofer Output Switch(ON/OFF) 21.Wall Mount Bracket 22. Coaxial2 Input Connector DESCRIPTION OF THE REMOTE 1. Standby/Power: Turn the unit on or off. 2. Input: Recycle select DISK --OPTICAL 1 4 TD er 12 --OPTICAL 2 --COAXIAL 1--COAXIAL 2 --AUX--TV input mode 2 2 | aD Gp 3. 0-+10 Number key Press to enter numbers, such as DVD part 3 D D | number, etc. 4. Setup ce @ Press to display the system setup picture on @ ED the screen. Thus, you can adjust the parameters 4 on the screen. You can also set up in similar ED (a EN — 13 ways, depending on your needs. 5. SD/USB a | Select SD or USB input mode. 6. [a] [У] [4] [>] Press to display menu or system function on screen. In player mode, press these buttons to move or select the function you need. 7. [REV] [FWD] Press to rewind or forward the track. 8. Enter/Play Press to confirm the option selected by the arrow buttons. Press to play the track. 9. [PREV ] [NEXT] Press and return to the previous part or skip to the next part. 10. Pause/Step Press to pause the playback. Press this button to play a scene frame by frame. 11. Repeat When you are playing DISC, you can press this button to select a certain portions of the content to be played repeatedly. 12. Mute Turn on or offthe sound 13. Listen Recycle select the listen mode: Pro-Logic ---Stereo---Vocal. 14. Stop Press to stop the track. 15. Master volume Master volume level up or down 16. Function The selection uses cycle loop. Choose LEFT, RIGHT, CENTER, SUB , BASS and TREBLE for level adjustment. To install / replace the batteries The remote control uses a pre-installed lithium battery. To prevent an anticipated discharge of the battery, we’ ve inserted an insulating strip. Please pull it out prior to first operation. Should the r/c start to work unreliably replace the battery with a new one of the same type. Open the battery compartment. Pull out the battery mounting in the direction of arrow. Before you take out the empty battery, please memorise its position. The + marking must show upwards, otherwise the r/c will not work and may be damaged. Replace the cover. Note: Please discard the used batteries properly. Never throw batteries into fire. -4- SYSTEM SETUP 4. DEFAULT: All functions resume initial statuses if you choose this option. | SYSTEM SETUP DEFAULT RESTORE Language Setup Use [aA] [W] [<] [>] buttons to select and highlight the option to be set, and use ENTER/PLAY button to confirm. 1. OSD LANGUAGE: There are 5 languages available to choice: ENGLISH, GERMAN, SPANISH, FRENCH, ITALIAN. “DER | LANGUAGE SETUP | OSD LANGUAGE ENGLISH Audio Setup Use [al[vi[l41[»1 buttons to select the highlighted mark to the option to be set, and use ENTER/PLAY button to confirm. 1. KEY: Press the direction button[Aa] [У] to move the indicator so as to set the tune. | AUDIO SETUP KEY SYSTEM SETUP The system can connect your TV use video output connector on the rear panel. Using the system setup menus: 1. Press the SETUP button on the remote control to display the SETUP menu as shown below. | SYSTEM SETUP 2. Use the «4 / buttons to select one of the SETUP options, highlight your desired selection with in each SETUP menu and press ENTER/PLAY button to confirm. 3. To exit the menu and go to another SETUP menu, use A /Y button to select EXIT SETUP. System Setup Use [A] [VW] [4] [ >] buttons to select the highlighted mark to the option to be set, and use ENTER/PLAY button to confirm. _ . TV SYSTEM: To be selected in accordance with the color system of the TV to be connected. a) NTSC: For NTSC zone, you can select "NTSC". (Used in the USA, Canada and Japan) b) PAL 60: For PAL 60 uniform zone, you can select "PAL 60". c) PAL: For PAL uniform zone, you can select "PAL". (Used in Western Europe) d) AUTO: For multiple zone, you can select "AUTO". 2. VIDEO You can choose this option if the system connects to TV through CVBS. © . ТУ ТУРЕ: a) 4:3PS (full-image scanning): available of the TV with average dimension. When a wide-screen picture is played, the left and right sides of the picture will be deleted and the picture will be seen on the screen. b) 4:3LB (mailbox): please choose this option for a TV with average dimensions. When the wide- screen picture is played, you will see black rims on the top and bottom of the TV screen. c) 16:09 (wide screen): choose this option if the system connects to a wide-screen TV. | SYSTEM SETUP | SYSTEM SETUP | SYSTEM SETUP TVSYSTEM | VIDEO см TV TYPE 2121 MAIN FEATURE * Simple to use e 2 Analog audio inputs ¢ 4 Digital audio inputs e Full function remote control e 4digit LED display ‚ 1 RCA video output, 1 RCA subwoofer output ‚ Individual channel volume control ° Dolby pro-logic and Dolby digital decoder built-in « USB prot and 3 in one card reader (SD/MMC/MS) support MP3/JPG/AVI/MPEG format Design to match 32” LCD panels, and sizes up to 42” LCD or PDP panels with optional built-in DVD players or Dolby decoder, and connects only external sound device (CD, DVD, VCD, Game system, Set top Box) SCENE 1 CONNECTIONS — Connect to any two channel (Right/left) sound source/device. (E.g. TV, DVD, CD player, xBox, Ps2, Computer etc.) / | \ a » (Optical cable ---Not include) -——— — ЕЕ Pr or ne CN A | DVD PS2 Ox 0% Connectto USB and SD/MMC/MS card. Note: + Do not connect the power cord into an AC outlet until all connections are made and are correct. » Please turn on the unit before turn on the external active subwoofer. « Please turn off the external active subwoofer before turn off the unit. -6- SYSTEM BASIC OPERATION 1. ON/OFF Plug in the power cord to the outlet, switch the MAIN POWER to ON position at the back of the unit, the unit goes into standby mode, the LED displays "HELLO". Press STANDBY button on the front panel or on the remote control to start the operation of the system. The system will automatically detect any input signal. If there is no signal present, the LED will display "NO SIGNAL". * Note: After shut off the unit, please wait at least 3 seconds before turn on it again. 2. INPUT MODE e The system is not connect the USB or SD memory card: Press INPUT button on the front panel or on the remote control to cycle through the selections: OPTICAL 1 --OPTICAL 2 --COAXIAL 1--COAXIAL 2--AUX--TV--USB/SD/MS/MMC input mode. * The system is connect the USB memory card: Press INPUT button on the front panel or on the remote control to cycle through the selections: OPTICAL 1 --OPTICAL 2 --COAXIAL 1--COAXIAL 2--AUX--TV--USB input mode. e The system is connectthe SD memory card: Press INPUT button on the front panel or on the remote control to cycle through the selections: OPTICAL 1 --OPTICAL 2 --COAXIAL 1--COAXIAL 2--AUX--TV--SD input mode. * The system is connect the USB and SD memory card: Press INPUT button on the front panel or on the remote control to cycle through the selections: OPTICAL 1 --OPTICAL 2 --COAXIAL 1--COAXIAL 2--AUX--TV--USB input mode. The system will select the USB input signal preference, then you can press USB/SD button to select the SD signal. 3. LISTENING MODE Press LISTEN button on the remote control to cycle through the listening modes:Stereo --Vocal --Pro-Logic. 4. VOLUME ADJUSTMENT (1) Master volume adjustment Master volume is controlled by the MASTER VOLUME +/- button on the remote control or VOL +/VOL - button on the front panel. (2) Subject volume adjustment Press FUNCTION button repeatedly to recycle select subject volume : TREBLE --BASS --FL--FR --CENTER --SUBWOOFER. Then press MASTER VOLUME button to control subject volume level up or down. 5. MUTE Press the MUTE button on the remote control, the system goes into mute mode. Press MUTE button again to disable the mute mode. The mute function will also be canceled automatically by pressing the MASTER VOLUME +/- buttons. 6. SELECT SUBWOOFER OUTPUT To connect an external active subwoofer, connect the monaural input jack of your subwooer to the SUBWOOFER OUTPUT jack of this unit. If a subwoofer is connected the unit, switch the SUB. SWITCH at the rear panel in OFF position. (The system default SUB. SWITCH in ON position.) ">
Advertisement