Model : PUMCL - CD Automation

Model : PUMCL - CD Automation
CAUTION
The contents of this manual are subject to change without notice. This manual is
complied with possible care for the purpose of accuracy, however, Fuji Electric
Systems shall not be held liable for any damages, including indirect damage,
caused by typographical errors, absence of information or use of information in
this manual.
Confirming Specifications and Accessories
Related Information
Refer to "Module Type Temperature
Controller Enhanced Communication
Module (CC-Link) User's Manual" for
details about the items described in this
manual.
Content
Material
name
Specification Catalog
Operating
CC-Link
instruction
Module
User’s
Manual
1 Unit
1 copy
1 Unit
Material No.
ECNO 1162
INPTN5A0200-E
2-3
2-4
Please read this section thoroughly before using, and observe the mentioned safety
warnings fully.
Safety warnings are categorized as “Warning” or “Caution”.
Warning
Improper use of the equipment may result in death or serious injuries.
Caution
Improper use of the equipment may cause injury to the user or property
damage.
2-5
-10 to 50 degree C
Ambient humidity
90% RH or below (with no condensation)
Vibration
10 to 70Hz less than 9.8m/s² (1G)
Warm-up time
30 min. or more
Installation category
IEC1010-1: class II
Pollution level
IEC1010-1: degree 2
5 6
70
CC-Link
communication
speed setting
LED indicator
Three color LED lamps indicate the following operational conditions.
LED
PWR
BUS
L. RUN
Green
Red
Orange
(In priority order)
OFF: Power is OFF
Flash: In a (0.4-second)
cycle:
1:Modules detected
by initial polling: 0
2:After initial polling,
an inter-module
communication
error occurs
Flash: In a (0.1 second)
cycle: Initial polling
ON: Running
―
―
ON:
Receiving by
inter-module
communication
ON: Data linking
OFF: H/W resetting, or
data linking not
performed
―
ON: Transmitting by
inter-module
communication
―
―
SD
RD
―
―
Communication speed
Communication speed
setting
Max. transmission distance
(Max. Network Length)
0
156kbps
1200m
1
625kbps
900m
2
2.5Mbps
400m
3
5Mbps
160m
4
10Mbps
100m
- When 5 to 9 are selected, a communication speed sellection error will occur and
[L.ERR] LED will be ON.
ON:
L.ERR
Communication error
(CRC error, Station
number setting error,
communication
speed setting error)
OFF: Receiving normally,
or while H/W
resetting
Flash: Setting switches
during the power ON
Communication speed and maximum transmission distance
(when using Ver.1.10 compliant CC-Link special cable)
- Setting No.of stations occupied / Extended cyclic
ON:
Transmitting the
CC-Link data
―
―
ON:
Receiving the
CC-Link data
―
―
No.of stations occupied/Extended cyclic can be set using the dip switch (SW1 to SW4)
on the back of the controller.
- Base part
Mounting screw hole
No.of stations occupied /
Extended cyclic setting
Module connector
(Connect modules laterally)
Module connector
Power terminal block
See [Wiring]
Mounting screw hole
See [Mounting]
Setting
Functional insulation (AC50V)
- Setting CC-Link Station No.
Station No. of CC-Link can be set using the Station No. configuration switch. Setting
range is 1 to 61.
Apply a fine tip flat-head screwdriver to turn the Station No. configuration switch.
BUS
STATION No.
x10
7 8
9 0 1
2 3
L.ERR
STATION No.
x10
7 8
4
LOADER
9 0 1
x1
7 8
9 0 1
SD
RD
x10 :
High order setting
(set value x 10)
2 3
x1
7 8
4
5 6
9 0 1
x1 :
Low order setting
(set value x 1)
2 3
Setting range :
1 to 61
(factory-set value = 0)
Maintenance
- When installing or removing the equipment, turn the power OFF. Otherwise, shock,
operational errors or failures may be caused.
- Periodic maintenance is recommended for continuous and safe use of this
equipment.
- Some parts installed on this equipment have a limited life and/or may deteriorate with
age.
- The warranty period for this unit (including accessories) is one year, if the product is
used properly.
- CC-Link communication can not perform with the factory-set value (0). Make sure to
set the Station No..
- When selected 0 or over 62, a Station No. selection error will occur and [L.ERR] LED
will be ON.
-1-
SW1
SW2
SW3
SW4
No.of stations occupied, Extended cyclic
(No.of Ch)
OFF
OFF
OFF
OFF
4 stations occupied x 1 (8Ch)
ON
OFF
OFF
OFF
4 stations occupied x 1 (16Ch)
OFF
ON
OFF
OFF
4 stations occupied x 2 (16Ch)
ON
ON
OFF
OFF
4 stations occupied x 2 (32Ch)
OFF
OFF
ON
OFF
4 stations occupied x 4 (32Ch)
ON
OFF
ON
OFF
4 stations occupied x 4 (64Ch)
Compliant
Ver.
Ver.1
Ver.2
- If the setting of the dip switch is other than those above, the actual setting will be "4
stations occupied x 1 (8Ch)"
PUM-C
PWR
L.RUN
5 6
Functional insulation (AC500V)
5 6
CC-Link communication
4
Loader communication
5 6
SLD/FG terminal (CC-Link connecting terminal)
4
Power
Locking tab
- In cases where damage or problems with this equipment may lead to serious
accidents, install appropriate external protective circuits.
- To prevent damage and failure of the equipment, provide the rated power voltage.
- To prevent electric shock and equipment failure, do not turn the power ON until all
wiring is complete.
- Before turning the power ON, confirm that clearance space has been secured to
prevent shock or fire.
- Do not touch the terminal while the machine is ON. Doing so risks shock or
equipment errors.
- Never disassemble, convert, modify or repair this equipment. Doing so risks abnormal
operation, shock or fire.
1-2
4
12
- Note that the insulation class for this equipment is as follows. Before installing,
please confirm that the insulation class for the equipment meets usage requirements.
Functional insulation (AC1000V)
Loader communication port
1 2 3 4 5 6
Installation and Wiring
LOADER
x1
Input/output
terminal block
See [Wiring]
Others
- Please do not wipe the equipment with organic solvents such as alcohol or benzene,
etc. If wiping is necessary, use a neutral cleaning agent.
- Do not use mobile phones near this equipment (within 50cm). Otherwise a
malfunction may result.
- Malfunctions may occur if the equipment is used near a radio, TV, or wireless device.
- This equipment requires approx. 20 seconds before it starts to output.
- Before installing and wiring, take necessary measures for electrostatic discharge
(ESD).
- This equipment is intended to be used under the following conditions.
Ambient temperature
Error Operation
- The alarm function does not work properly when an error occurs unless the settings
are made correctly. Always verify its setting before operation.
1 * Warning
1-1
Cautions for Wiring
- For wiring to terminal blocks, apply crimp terminals for M3 screw.
Screw size
: M3 x 7 (with square washer)
Screw tightening torque: 0.78 N•m (8 kgf•cm)
- To avoid noise conductor effects, input signal wires should be separated from electric
power lines or load lines.
- To comply with CE marking (EMC), we recommend to attach ferrite core to
communication cable and power cable.
Please Read First (Safety Warnings)
RD
Cautions when Attaching to DIN rails
- In case of mounting the temperature controllers to DIN rails, remember to push up
the locking tabs to fasten the controllers onto DIN rail.
- To connect controllers, first release all locking tabs. Then, connect controllers and
push up all locking tabs. Make sure that all locking tabs are fastened.
- Never fail to turn the power OFF, before detaching the terminal block or removing the
main unit from the base part.
- In order to aid heat dissipation, do not block the top and the bottom of the equipment.
- When mounting / dismounting controllers to / from DIN rails, 30mm of clearance
above and under the controllers should be provided.
- Do not use the terminal screws other than those supplied with this product.
STATION No.
x10
7 8
7 8
SD
2 3
Temperature Controller Enhanced
Communication Module (CC-Link) Instruction Manual
Internal Communication Termination
Resistance (100 Ω)
2-2
BUS
L.ERR
34
Thank you for purchasing the Fuji module type temperature controller. Once you have
confirmed that this is the product you ordered, please use it in accordance with the
following instructions.For detailed information on operating this equipment, please refer
to the separate user's manual. Please keep this Instruction Manual within easy reach of
persons using this equipment
PWR
L.RUN
LED indicator
9 0 1
INP-TN1PUMCL-E
Station No.
Configuration switch
See [Setting]
PUM-C
9 0 1
Please avoid installing in the following locations.
- Locations in which the ambient temperature falls outside the range of 0 to 50 degree
C when equipment is in use.
- Locations in which the ambient humidity falls outside the range of 45 to 85% RH
when equipment is in use.
- Locations with rapid temperature changes, leading to dew condensation.
- Locations with corrosive gases (especially sulfide gas, ammonia, etc.) or flammable
gases.
- Locations with vibration or shock directly.
- Locations in contact with water, oil, chemicals, steam or hot water.
(If the equipment gets wet, there is a risk of electric shock or fire, so have it inspected
by Fuji distributor.)
- Locations with high concentrations of atmospheric dust, salt or iron particles.
- Locations with large inductive interference, resulting in static electricity, magnetic
fields or noise.
- Locations in direct sunlight.
- Locations that build up heat from radiant heat sources, etc.
Model : PUMCL
Before using the product, confirm that it
matches the type ordered.
(For model code, please refer to page 4.)
Confirm that all of the following
accessories are included.
Cautions when Installing
5 6
2-1
4
Enhanced Communication Module
(CC-Link)
Communication speed of CC-Link can be set using the station number configuration
switch on the back of the controller.
Apply a fine tip flat-head screwdriver to turn the Station No. configuration switch.
- Enhanced communication module controller
56
Multi-loop Module Type Temperature Controller
- Setting CC-Link Communication speed.
Part names and Functions
2 3
2 * Caution
2 3
Instruction Manual (Installation)
-2-
CAUTION
The contents of this manual are subject to change without notice. This manual is
complied with possible care for the purpose of accuracy, however, Fuji Electric
Systems shall not be held liable for any damages, including indirect damage,
caused by typographical errors, absence of information or use of information in
this manual.
Confirming Specifications and Accessories
Related Information
Refer to "Module Type Temperature
Controller Enhanced Communication
Module (CC-Link) User's Manual" for
details about the items described in this
manual.
Content
Material
name
Specification Catalog
Operating
CC-Link
instruction
Module
User’s
Manual
1 Unit
1 copy
1 Unit
Material No.
ECNO 1162
INPTN5A0200-E
2-3
2-4
Please read this section thoroughly before using, and observe the mentioned safety
warnings fully.
Safety warnings are categorized as “Warning” or “Caution”.
Warning
Improper use of the equipment may result in death or serious injuries.
Caution
Improper use of the equipment may cause injury to the user or property
damage.
2-5
-10 to 50 degree C
Ambient humidity
90% RH or below (with no condensation)
Vibration
10 to 70Hz less than 9.8m/s² (1G)
Warm-up time
30 min. or more
Installation category
IEC1010-1: class II
Pollution level
IEC1010-1: degree 2
5 6
70
CC-Link
communication
speed setting
LED indicator
Three color LED lamps indicate the following operational conditions.
LED
PWR
BUS
L. RUN
Green
Red
Orange
(In priority order)
OFF: Power is OFF
Flash: In a (0.4-second)
cycle:
1:Modules detected
by initial polling: 0
2:After initial polling,
an inter-module
communication
error occurs
Flash: In a (0.1 second)
cycle: Initial polling
ON: Running
―
―
ON:
Receiving by
inter-module
communication
ON: Data linking
OFF: H/W resetting, or
data linking not
performed
―
ON: Transmitting by
inter-module
communication
―
―
SD
RD
―
―
Communication speed
Communication speed
setting
Max. transmission distance
(Max. Network Length)
0
156kbps
1200m
1
625kbps
900m
2
2.5Mbps
400m
3
5Mbps
160m
4
10Mbps
100m
- When 5 to 9 are selected, a communication speed sellection error will occur and
[L.ERR] LED will be ON.
ON:
L.ERR
Communication error
(CRC error, Station
number setting error,
communication
speed setting error)
OFF: Receiving normally,
or while H/W
resetting
Flash: Setting switches
during the power ON
Communication speed and maximum transmission distance
(when using Ver.1.10 compliant CC-Link special cable)
- Setting No.of stations occupied / Extended cyclic
ON:
Transmitting the
CC-Link data
―
―
ON:
Receiving the
CC-Link data
―
―
No.of stations occupied/Extended cyclic can be set using the dip switch (SW1 to SW4)
on the back of the controller.
- Base part
Mounting screw hole
No.of stations occupied /
Extended cyclic setting
Module connector
(Connect modules laterally)
Module connector
Power terminal block
See [Wiring]
Mounting screw hole
See [Mounting]
Setting
Functional insulation (AC50V)
- Setting CC-Link Station No.
Station No. of CC-Link can be set using the Station No. configuration switch. Setting
range is 1 to 61.
Apply a fine tip flat-head screwdriver to turn the Station No. configuration switch.
BUS
STATION No.
x10
7 8
9 0 1
2 3
L.ERR
STATION No.
x10
7 8
4
LOADER
9 0 1
x1
7 8
9 0 1
SD
RD
x10 :
High order setting
(set value x 10)
2 3
x1
7 8
4
5 6
9 0 1
x1 :
Low order setting
(set value x 1)
2 3
Setting range :
1 to 61
(factory-set value = 0)
Maintenance
- When installing or removing the equipment, turn the power OFF. Otherwise, shock,
operational errors or failures may be caused.
- Periodic maintenance is recommended for continuous and safe use of this
equipment.
- Some parts installed on this equipment have a limited life and/or may deteriorate with
age.
- The warranty period for this unit (including accessories) is one year, if the product is
used properly.
- CC-Link communication can not perform with the factory-set value (0). Make sure to
set the Station No..
- When selected 0 or over 62, a Station No. selection error will occur and [L.ERR] LED
will be ON.
-1-
SW1
SW2
SW3
SW4
No.of stations occupied, Extended cyclic
(No.of Ch)
OFF
OFF
OFF
OFF
4 stations occupied x 1 (8Ch)
ON
OFF
OFF
OFF
4 stations occupied x 1 (16Ch)
OFF
ON
OFF
OFF
4 stations occupied x 2 (16Ch)
ON
ON
OFF
OFF
4 stations occupied x 2 (32Ch)
OFF
OFF
ON
OFF
4 stations occupied x 4 (32Ch)
ON
OFF
ON
OFF
4 stations occupied x 4 (64Ch)
Compliant
Ver.
Ver.1
Ver.2
- If the setting of the dip switch is other than those above, the actual setting will be "4
stations occupied x 1 (8Ch)"
PUM-C
PWR
L.RUN
5 6
Functional insulation (AC500V)
5 6
CC-Link communication
4
Loader communication
5 6
SLD/FG terminal (CC-Link connecting terminal)
4
Power
Locking tab
- In cases where damage or problems with this equipment may lead to serious
accidents, install appropriate external protective circuits.
- To prevent damage and failure of the equipment, provide the rated power voltage.
- To prevent electric shock and equipment failure, do not turn the power ON until all
wiring is complete.
- Before turning the power ON, confirm that clearance space has been secured to
prevent shock or fire.
- Do not touch the terminal while the machine is ON. Doing so risks shock or
equipment errors.
- Never disassemble, convert, modify or repair this equipment. Doing so risks abnormal
operation, shock or fire.
1-2
4
12
- Note that the insulation class for this equipment is as follows. Before installing,
please confirm that the insulation class for the equipment meets usage requirements.
Functional insulation (AC1000V)
Loader communication port
1 2 3 4 5 6
Installation and Wiring
LOADER
x1
Input/output
terminal block
See [Wiring]
Others
- Please do not wipe the equipment with organic solvents such as alcohol or benzene,
etc. If wiping is necessary, use a neutral cleaning agent.
- Do not use mobile phones near this equipment (within 50cm). Otherwise a
malfunction may result.
- Malfunctions may occur if the equipment is used near a radio, TV, or wireless device.
- This equipment requires approx. 20 seconds before it starts to output.
- Before installing and wiring, take necessary measures for electrostatic discharge
(ESD).
- This equipment is intended to be used under the following conditions.
Ambient temperature
Error Operation
- The alarm function does not work properly when an error occurs unless the settings
are made correctly. Always verify its setting before operation.
1 * Warning
1-1
Cautions for Wiring
- For wiring to terminal blocks, apply crimp terminals for M3 screw.
Screw size
: M3 x 7 (with square washer)
Screw tightening torque: 0.78 N•m (8 kgf•cm)
- To avoid noise conductor effects, input signal wires should be separated from electric
power lines or load lines.
- To comply with CE marking (EMC), we recommend to attach ferrite core to
communication cable and power cable.
Please Read First (Safety Warnings)
RD
Cautions when Attaching to DIN rails
- In case of mounting the temperature controllers to DIN rails, remember to push up
the locking tabs to fasten the controllers onto DIN rail.
- To connect controllers, first release all locking tabs. Then, connect controllers and
push up all locking tabs. Make sure that all locking tabs are fastened.
- Never fail to turn the power OFF, before detaching the terminal block or removing the
main unit from the base part.
- In order to aid heat dissipation, do not block the top and the bottom of the equipment.
- When mounting / dismounting controllers to / from DIN rails, 30mm of clearance
above and under the controllers should be provided.
- Do not use the terminal screws other than those supplied with this product.
STATION No.
x10
7 8
7 8
SD
2 3
Temperature Controller Enhanced
Communication Module (CC-Link) Instruction Manual
Internal Communication Termination
Resistance (100 Ω)
2-2
BUS
L.ERR
34
Thank you for purchasing the Fuji module type temperature controller. Once you have
confirmed that this is the product you ordered, please use it in accordance with the
following instructions.For detailed information on operating this equipment, please refer
to the separate user's manual. Please keep this Instruction Manual within easy reach of
persons using this equipment
PWR
L.RUN
LED indicator
9 0 1
INP-TN1PUMCL-E
Station No.
Configuration switch
See [Setting]
PUM-C
9 0 1
Please avoid installing in the following locations.
- Locations in which the ambient temperature falls outside the range of 0 to 50 degree
C when equipment is in use.
- Locations in which the ambient humidity falls outside the range of 45 to 85% RH
when equipment is in use.
- Locations with rapid temperature changes, leading to dew condensation.
- Locations with corrosive gases (especially sulfide gas, ammonia, etc.) or flammable
gases.
- Locations with vibration or shock directly.
- Locations in contact with water, oil, chemicals, steam or hot water.
(If the equipment gets wet, there is a risk of electric shock or fire, so have it inspected
by Fuji distributor.)
- Locations with high concentrations of atmospheric dust, salt or iron particles.
- Locations with large inductive interference, resulting in static electricity, magnetic
fields or noise.
- Locations in direct sunlight.
- Locations that build up heat from radiant heat sources, etc.
Model : PUMCL
Before using the product, confirm that it
matches the type ordered.
(For model code, please refer to page 4.)
Confirm that all of the following
accessories are included.
Cautions when Installing
5 6
2-1
4
Enhanced Communication Module
(CC-Link)
Communication speed of CC-Link can be set using the station number configuration
switch on the back of the controller.
Apply a fine tip flat-head screwdriver to turn the Station No. configuration switch.
- Enhanced communication module controller
56
Multi-loop Module Type Temperature Controller
- Setting CC-Link Communication speed.
Part names and Functions
2 3
2 * Caution
2 3
Instruction Manual (Installation)
-2-
Front screw terminal cover
(optional)
Please prepare power cables and crimp terminals of the size indicated below.
Power cable
- Front terminal block
BUS
L.RUN
Cable type
Thermocouple (Compensation lead wire)
Power supply
PUM-C
PWR
STATION No.
x10
7 8
5 6
- Dimensions
Crimp terminal size
Wiring
LOADER
9 0 1
When mounting controllers inside a cabinet with screws, connect the base parts of
controllers first.
- Fixing screws are not included. Please prepare screws as required.
1. Refer to the figure below for the mounting
(30)
screw hole size to decide the mounting position.
2-M3
9±0.2
4
- Fixing with screws
Mounting
2 3
5 6
4
5 6
4
21
21
50
5 6
4
2 3
6
DB
(100)
88.5 ±0.2
x1
11
11
CC-Link
DG
12
100
SLD
22
22
12
23
23
13
24
24
14
25
15
26
16
27
17
28
18
29
19
30
20
25
Vacant
4. Fixate the base parts onto the mounting position inside the cabinet with screws.
(mm)
5. Attach the main units to the base parts.
Cautions when mounting
In order to aid heat dissipation, 30mm of clearance (50mm recommended) above and
under the controllers should be provided.
STATION No.
x10
7 8
LOADER
1
2
3
4
5
4 5 6
PWR
PUM-A
COM
LOADER
7
8
Contents
Module type
Advanced communication module
Communication function
CC-Link communication
Instruction manual
Japanese
English
C
L
STATION
x1
Power Terminal
345
F012
OUT3
OUT4
E
7 8
2. Connect controllers with each other using
side connectors.
Y crimp terminal
9 10
OUT2
8 9A
67
SD
RD
6
Y Y 1 - 0
OUT1
L.ERR
9 0 1
30 or more
BUS
Ring crimp terminal
Enhanced communication module (CC-Link)
- Base part (power terminal)
PUM-C
PWR
L.RUN
9 0 1
1. Check that locking tabs are pulled down
(released).
φ3.2mm
Model code
P U M
- Connecting controllers
0.8 N•m
Vacant
* This terminating resistance is different from the CC-Link terminating resistance
(this is the terminating resistance for inter-module communication).
Install the resistance (100Ω) supplied with this controller.
4 5 6
(30)
[mm]
3. Connect base parts. Push up to fasten all the locking tabs.
Main unit (when detached from the base part)
When locking tab is released
(when mounting / dismounting to / from DIN rails)
30
2 3
(8)
2. Remove the main units from the base part.
See [How to detach the base part]
Terminal
screw size M3
+0.7
+0.2
2 3
5
Terminal
screw
size M3
(3)
FG
Screw tightening torque
0.25 to 1.25mm2
A
B
BCD
6.1
DIN rail
Cable size
Internal Communication
Terminating Resistance
(option)*
3.2mm
LOADER
Crimp terminal
6.0mm or less
DA
PUM-C
x1
7 8
2 3
RD
7 8
9 0 1
1.5
SD
RD
6.0mm or less
STATION No.
x10
7 8
L.ERR
SD
85
9 0 1
BUS
L.ERR
2 3
PWR
L.RUN
(10)
Base part
(when detached from
the main unit)
9 0 1
Terminal block
(when detached
from the
main unit)
30
Size
1.25mm2 or less
1.25mm2 or less
DC 24V (‑)
DC 24V (+)
Accessories (Optional)
Side connector
30 or more
Note: The power cables more than one should not be connected.
1
PUM-A
COM
LOADER
STATION
345
OUT3
OUT4
STATION
345
F012
OUT4
F012
OUT3
E
OUT2
E
5 6
4
PWR
OUT1
BCD
2 3
5 6
LOADER
7 8 9A
4
PUM-A
COM
OUT2
BCD
x1
7 8
PWR
OUT1
6
2 3
SD
RD
LOADER
7 8 9A
Hook the back
of controller
PUM-C
STATION No.
x10
7 8
6
1. Pull down the locking tab of the
base part. Hook the back of the
controller onto the upper part of
DiN rail.
2. Push the controller in the
direction of arrow 2.
BUS
L.ERR
9 0 1
- Mounting to DIN rails
PWR
L.RUN
9 0 1
3. After mounting connected controllers onto
DIN rail, make sure to push up all locking
tabs. Controllers are fastened to DIN rail and
to each other.
4. All connected controllers are connected to
power supply via side connectors if one of
controllers is directly connected to them.
DIN rail
Locking tab
3. Push up the locking tab to fasten
the controller to DIN rail.
- When connecting controllers after
attaching to DIN rail, push up
the locking tab after connecting
controllers.
How to detach the base part
1. Press the lock lever on the top of the
controller.
Lock lever
2. Pull down the upper part of main unit.
When attaching controllers to DIN rails, we recommend to attach side connecting
terminal covers (right and left 1set), then end plates (option) to the ends of the right
most and left most controllers.
PUM-E
PWR
LOADER
COM
STATION
345
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
PUM-E
LOADER
DIN rail mounting
end plate
STATION
F012
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
345
Main
7 8 9A
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
E
COM
F012
PWR
LOADER
345
4
5
6
7
8
A
A
A
L
0
0
0
0
2
3
4
1
General Specification
Contents
DIN rail mounting end plate
Side connecting terminal cover (right & left 1 set)
Front face screw terminal cover
Loader connecting cable (RS-232C)
Power Supply
Power Consumption
Dimensions
:DC24V±10%
:Maximum 3.2W (135mA) [when DC24V is applied]
:30 (W) × 100 (H) × 85 (D) mm (excluding the terminal cover and a
projection)
Weight
:Approx. 200 g
Installation method
:Mounting on the wall or, install in the cabinet with the DIN rail with M3
screws
Ambient temperature * :-10 to 50 degrees C
*"Ambient temperature" is the temperature underneath the controller
inside equipment or the cabinet where the controller is installed.
Ambient humidity
:90% RH or less (non condensing)
Memory backup
: Nonvolatile memory (EEPROM) backup
No.of updates : 100,000
Communication function
Compliant version
:CC-Link Ver.2.00 / 1.10
Station type
:Remote device station
Communication speed and distance
625kbps
2.5Mbps
900m or less
400m or less
5Mbps
200m or less
10Mbps
100m or less
No. of stations occupied / Station No.: 4 stations / Settable Station No. 1 to 61
Communication data length
6
F012
PUM-E
STATION
7 8 9A
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
7 8 9A
OUT4
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
E
COM
345
F012
PWR
LOADER
STATION
6
OUT3
E
PUM-A
COM
OUT2
E
5 6
4
PWR
OUT1
6
2 3
5 6
LOADER
7 8 9A
4
PUM-C
BCD
x1
6
2 3
RD
7 8
BCD
STATION No.
x10
7 8
9 0 1
SD
BCD
BUS
L.ERR
BCD
PWR
L.RUN
9 0 1
DIN rail mounting
end plate
3
*For more details, refer to “CC-Link Cable Wiring Manual” issued by CC-Link Partner Association.
- When attaching the main unit to the
base part, take the reverse procedure
to removing the main unit from the
base part.
- Make sure that the lock lever of the
main unit is fitted into the base part.
- Attaching end plates
Specification
Communication
156kbps
speed
Communication 1200m or less
distance
3. Detach the cutout on the lower end
of back of the main unit from the
projection on the base part.
2
P U M Z *
Locking tab
Projection
No.of stations occupied / Remote input/output
Extended cyclic
(RX/RY)
Remote register
(RWr/RWw)
4 stations occupied x 1
4 stations occupied x 2
4 stations occupied x 4
16 words each
32 words each
64 words each
Connecting cable
Connecting method
Terminating resistance
128 bit each
256 bit each
512 bit each
Control module
(PUM-A) No. of
connectable units
2 or 4 units
4 or 8 units
8 or 16 units
: Ver.1.10 compliant CC-Link special cable
: M3 screw terminal block
: External (110 ohm, 1/2W)
Head Office
Gate City Osaki East Tower 11-2, Osaki 1-chome, Shinagawa-ku, Tokyo 141-0032, Japan
http://www.fesys.co.jp/eng
Side connecting terminal cover
(right & left 1 set)
-3-
-4-
Front screw terminal cover
(optional)
Please prepare power cables and crimp terminals of the size indicated below.
Power cable
- Front terminal block
BUS
L.RUN
Cable type
Thermocouple (Compensation lead wire)
Power supply
PUM-C
PWR
STATION No.
x10
7 8
5 6
- Dimensions
Crimp terminal size
Wiring
LOADER
9 0 1
When mounting controllers inside a cabinet with screws, connect the base parts of
controllers first.
- Fixing screws are not included. Please prepare screws as required.
1. Refer to the figure below for the mounting
(30)
screw hole size to decide the mounting position.
2-M3
9±0.2
4
- Fixing with screws
Mounting
2 3
5 6
4
5 6
4
21
21
50
5 6
4
2 3
6
DB
(100)
88.5 ±0.2
x1
11
11
CC-Link
DG
12
100
SLD
22
22
12
23
23
13
24
24
14
25
15
26
16
27
17
28
18
29
19
30
20
25
Vacant
4. Fixate the base parts onto the mounting position inside the cabinet with screws.
(mm)
5. Attach the main units to the base parts.
Cautions when mounting
In order to aid heat dissipation, 30mm of clearance (50mm recommended) above and
under the controllers should be provided.
STATION No.
x10
7 8
LOADER
1
2
3
4
5
4 5 6
PWR
PUM-A
COM
LOADER
7
8
Contents
Module type
Advanced communication module
Communication function
CC-Link communication
Instruction manual
Japanese
English
C
L
STATION
x1
Power Terminal
345
F012
OUT3
OUT4
E
7 8
2. Connect controllers with each other using
side connectors.
Y crimp terminal
9 10
OUT2
8 9A
67
SD
RD
6
Y Y 1 - 0
OUT1
L.ERR
9 0 1
30 or more
BUS
Ring crimp terminal
Enhanced communication module (CC-Link)
- Base part (power terminal)
PUM-C
PWR
L.RUN
9 0 1
1. Check that locking tabs are pulled down
(released).
φ3.2mm
Model code
P U M
- Connecting controllers
0.8 N•m
Vacant
* This terminating resistance is different from the CC-Link terminating resistance
(this is the terminating resistance for inter-module communication).
Install the resistance (100Ω) supplied with this controller.
4 5 6
(30)
[mm]
3. Connect base parts. Push up to fasten all the locking tabs.
Main unit (when detached from the base part)
When locking tab is released
(when mounting / dismounting to / from DIN rails)
30
2 3
(8)
2. Remove the main units from the base part.
See [How to detach the base part]
Terminal
screw size M3
+0.7
+0.2
2 3
5
Terminal
screw
size M3
(3)
FG
Screw tightening torque
0.25 to 1.25mm2
A
B
BCD
6.1
DIN rail
Cable size
Internal Communication
Terminating Resistance
(option)*
3.2mm
LOADER
Crimp terminal
6.0mm or less
DA
PUM-C
x1
7 8
2 3
RD
7 8
9 0 1
1.5
SD
RD
6.0mm or less
STATION No.
x10
7 8
L.ERR
SD
85
9 0 1
BUS
L.ERR
2 3
PWR
L.RUN
(10)
Base part
(when detached from
the main unit)
9 0 1
Terminal block
(when detached
from the
main unit)
30
Size
1.25mm2 or less
1.25mm2 or less
DC 24V (‑)
DC 24V (+)
Accessories (Optional)
Side connector
30 or more
Note: The power cables more than one should not be connected.
1
PUM-A
COM
LOADER
STATION
345
OUT3
OUT4
STATION
345
F012
OUT4
F012
OUT3
E
OUT2
E
5 6
4
PWR
OUT1
BCD
2 3
5 6
LOADER
7 8 9A
4
PUM-A
COM
OUT2
BCD
x1
7 8
PWR
OUT1
6
2 3
SD
RD
LOADER
7 8 9A
Hook the back
of controller
PUM-C
STATION No.
x10
7 8
6
1. Pull down the locking tab of the
base part. Hook the back of the
controller onto the upper part of
DiN rail.
2. Push the controller in the
direction of arrow 2.
BUS
L.ERR
9 0 1
- Mounting to DIN rails
PWR
L.RUN
9 0 1
3. After mounting connected controllers onto
DIN rail, make sure to push up all locking
tabs. Controllers are fastened to DIN rail and
to each other.
4. All connected controllers are connected to
power supply via side connectors if one of
controllers is directly connected to them.
DIN rail
Locking tab
3. Push up the locking tab to fasten
the controller to DIN rail.
- When connecting controllers after
attaching to DIN rail, push up
the locking tab after connecting
controllers.
How to detach the base part
1. Press the lock lever on the top of the
controller.
Lock lever
2. Pull down the upper part of main unit.
When attaching controllers to DIN rails, we recommend to attach side connecting
terminal covers (right and left 1set), then end plates (option) to the ends of the right
most and left most controllers.
PUM-E
PWR
LOADER
COM
STATION
345
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
PUM-E
LOADER
DIN rail mounting
end plate
STATION
F012
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
345
Main
7 8 9A
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
E
COM
F012
PWR
LOADER
345
4
5
6
7
8
A
A
A
L
0
0
0
0
2
3
4
1
General Specification
Contents
DIN rail mounting end plate
Side connecting terminal cover (right & left 1 set)
Front face screw terminal cover
Loader connecting cable (RS-232C)
Power Supply
Power Consumption
Dimensions
:DC24V±10%
:Maximum 3.2W (135mA) [when DC24V is applied]
:30 (W) × 100 (H) × 85 (D) mm (excluding the terminal cover and a
projection)
Weight
:Approx. 200 g
Installation method
:Mounting on the wall or, install in the cabinet with the DIN rail with M3
screws
Ambient temperature * :-10 to 50 degrees C
*"Ambient temperature" is the temperature underneath the controller
inside equipment or the cabinet where the controller is installed.
Ambient humidity
:90% RH or less (non condensing)
Memory backup
: Nonvolatile memory (EEPROM) backup
No.of updates : 100,000
Communication function
Compliant version
:CC-Link Ver.2.00 / 1.10
Station type
:Remote device station
Communication speed and distance
625kbps
2.5Mbps
900m or less
400m or less
5Mbps
200m or less
10Mbps
100m or less
No. of stations occupied / Station No.: 4 stations / Settable Station No. 1 to 61
Communication data length
6
F012
PUM-E
STATION
7 8 9A
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
7 8 9A
OUT4
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
E
COM
345
F012
PWR
LOADER
STATION
6
OUT3
E
PUM-A
COM
OUT2
E
5 6
4
PWR
OUT1
6
2 3
5 6
LOADER
7 8 9A
4
PUM-C
BCD
x1
6
2 3
RD
7 8
BCD
STATION No.
x10
7 8
9 0 1
SD
BCD
BUS
L.ERR
BCD
PWR
L.RUN
9 0 1
DIN rail mounting
end plate
3
*For more details, refer to “CC-Link Cable Wiring Manual” issued by CC-Link Partner Association.
- When attaching the main unit to the
base part, take the reverse procedure
to removing the main unit from the
base part.
- Make sure that the lock lever of the
main unit is fitted into the base part.
- Attaching end plates
Specification
Communication
156kbps
speed
Communication 1200m or less
distance
3. Detach the cutout on the lower end
of back of the main unit from the
projection on the base part.
2
P U M Z *
Locking tab
Projection
No.of stations occupied / Remote input/output
Extended cyclic
(RX/RY)
Remote register
(RWr/RWw)
4 stations occupied x 1
4 stations occupied x 2
4 stations occupied x 4
16 words each
32 words each
64 words each
Connecting cable
Connecting method
Terminating resistance
128 bit each
256 bit each
512 bit each
Control module
(PUM-A) No. of
connectable units
2 or 4 units
4 or 8 units
8 or 16 units
: Ver.1.10 compliant CC-Link special cable
: M3 screw terminal block
: External (110 ohm, 1/2W)
Head Office
Gate City Osaki East Tower 11-2, Osaki 1-chome, Shinagawa-ku, Tokyo 141-0032, Japan
http://www.fesys.co.jp/eng
Side connecting terminal cover
(right & left 1 set)
-3-
-4-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement