VSN1190 wall controller user manual
1190
User Manual
Version 2.0.0
Contents
Introduction.......................................................................................................................4
Unpacking..........................................................................................................................5
The VSN1190......................................................................................................................6
Specifications.....................................................................................................................7
Software............................................................................................................................8
ImageDP4 Video BIOS........................................................................................................8
Hardware Installation........................................................................................................11
Filter Maintenance.............................................................................................................15
Datapath Limited..............................................................................................................16
FCC Statement..................................................................................................................17
Index.................................................................................................................................18
2
Safety Instructions
Safety Instructions (UK)
Instrucciones de seguridad (Esp)
(USA)
Rogamos leer las siguientes instrucciones de seguridad antes de poner en funcionamiento el equipo, a fin de evitar daños en su producto
de Datapath o lesiones al personal encargado de su manejo. Poner estas instrucciones a disposición de todos aquellos que vayan a
utilizar y/o manejar los productos de Datapath.
To prevent damage to your Datapath product or injury to personnel operating the equipment, please read the following safety precautions prior to operation. These instructions should be made available to all those who will use and operate Datapath products.
Power Supply
Alimentación eléctrica
All Datapath products require a mains power supply. This power supply must be disconnected when equipment is being upgraded or
relocated.
Todos los productos de Datapath requieren una fuente de alimentación eléctrica. Esta fuente de alimentación eléctrica debe ser
desconectada durante las tareas de renovación o traslado.
Cables
Cables
Do not expose cables to any liquids; doing so may cause a short circuit which could damage the
equipment. Do not place heavy objects on top of any cables as this can cause damage and possibly lead to exposed live wires.
No exponer los cables a líquidos, ya que ello puede causar un cortocircuito y, por consiguiente, daños en el equipo. No colocar objetos
pesados sobre los cables, ya que esto puede ocasionar daños y poner al descubierto los cables vivos.
Ventilation
Ventilación
All computer equipment should be located in a well ventilated area. All ventilation holes on the computer casing must be kept clear of
any obstruction at all times. Failure to do so will result in the system over heating and damaging your equipment.
Todos los equipos informáticos deben estar situados en un área bien ventilada. Mantener todos los orificios de ventilación de la carcasa
del ordenador siempre libres de obstrucciones de cualquier tipo. En caso contrario, podría producirse un sobrecalentamiento del
sistema y daños en el equipo.
Working Environment
The equipment should be located in an environment free from dust, moisture and extreme changes in temperature and should be
placed on a stable and solid work surface. Liquids (hot/cold drinks etc) should not be placed near the equipment as spillage could
cause serious damage.
Entorno de trabajo
El equipo debe estar emplazado en un ambiente sin polvo, humedad ni cambios bruscos de temperatura y debe ser situado sobre una
superficie estable y sólida. No colocar líquidos (bebidas calientes/frías, etc.) cerca del equipo, ya que un derrame podría causar graves
daños.
Gas/Flammable Liquids
Electronic equipment should never be used in the presence of gas or any flammable liquid, doing so could result in an explosion or
serious fire.
Gas/líquidos inflamables
El equipo electrónico nunca debe ser usado en presencia de gas o líquido inflamable, ya que esto podría causar una explosión o un
incendio grave.
Smoke/Unusual Smells
Should you notice smoke or unusual smells being emitted from your computer, turn off and unplug the system from the mains supply.
The system should then be passed to a qualified technician for
inspection. Continued operation could result in personal injury and damage to property.
Humo/olores inusuales
En caso de percibir humo u olores inusuales provenientes de su ordenador, apagar y desenchufar el equipo de la red eléctrica. El sistema
debe ser confiado entonces a un técnico cualificado para su
Maintenance
inspección. Si el equipo continuara funcionando, esto podría ocasionar lesiones personales y daños materiales.
Maintenance should only be carried out by competent technicians, any Datapath plug-in cards that are physically damaged should be
returned to Datapath for repair using Datapath RMA procedures.
Mantenimiento
El mantenimiento solo debe ser ejecutado por técnicos capacitados. Las tarjetas insertables (plug-in) de Datapath que estén físicamente
dañadas deben ser devueltas a Datapath para su reparación según los procedimientos RMA (Return Merchandise Agreement) de
Datapath.
Disposal
At the end of life all Datapath products should be disposed of as per local laws and regulations dictate. In UK contact Datapath to
arrange disposal. Our WEE registration number is WEEE/AA0005ZR.
Eliminación
Rack Mount Safety Instructions
Al final de su vida útil, todos los productos de Datapath deben ser eliminados de acuerdo con las leyes y normativas locales. En el
Reino Unido, contactar a Datapath para organizar la eliminación. Nuestro número de registro WEE (Waste Electrical and Electronic
Equipment) es WEEE/AA0005ZR.
Temperature
If VSN1190 systems are to be installed in a closed or multi-unit rack assembly, the installation should be such that the amount of air
flow required for safe operation of the equipment is not compromised. The operating ambient temperature of the rack environment
should be maintained below 35 degrees centigrade under all conditions. Appropriate cooling arrangements should be built into the
cabinet to ensure that this specification is maintained.
Instrucciones de seguridad para montaje en bastidor
Temperatura
Si los sistemas VSN1190 se montan en un bastidor cerrado o en un bastidor de varias unidades, la instalación se deberá realizar evitando
que afecte al flujo de aire necesario para un funcionamiento seguro. Mantener la temperatura ambiente del entorno del bastidor por
debajo de los 35 grados centígrados bajo todo tipo de condiciones. Instalar en el armario los dispositivos adecuados de refrigeración a
fin de asegurar que se cumpla esta especificación.
Mechanical Loading
Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.
Circuit Overloading
Carga mecánica
Consideration should be given to the connection of the equipment to the mains supply circuit and the effect that overloading of the
supply might have on any overcurrent protection or supply wiring. Appropriate consideration of equipment nameplate ratings should
be used when addressing this concern.
Efectuar el montaje del equipo en el bastidor de tal modo que se eviten situaciones de peligro debidas a una carga mecánica irregular.
Sobrecarga del circuito
Reliable Earthing
Reliable earthing of all rack-mounted equipment should be maintained. Particular attention should be given to supply connections
other than direct connections to the branch circuit (e.g. use of power strips).
Tener especial cuidado al realizar la conexión del equipo al circuito de la red eléctrica a fin de evitar que una sobrecarga de ésta pueda
afectar a algún dispositivo de protección contra corriente de sobreintensidad o al cableado de alimentación. Tener en cuenta las capacidades especificadas en la placa indicadora del equipo al conectarlo a la red.
Replaceable Batteries
Puesta a tierra segura
Caution: Risk of Explosion if Battery is replaced by an Incorrect Type.
Asegurar la puesta a tierra segura de todos los equipos montados en bastidor. Prestar especial atención a las conexiones de alimentación
que no sean conexiones directas al circuito en derivación (por ejemplo, mediante regletas).
Dispose of Used Batteries According to the local laws / regulations and manufacturer’s instructions.
Baterías reemplazables
Precaución: Riesgo de explosión si la batería se sustituye por otra de tipo incorrecto.
Deseche las baterías usadas según las leyes / regulaciones locales y las instrucciones del fabricante.
Consignes de sécurité (Fr)
Sicherheitsanweisungen (D)
Afin de ne pas endommager votre produit Datapath et d’éviter tout risque de blessure du personnel exploitant le matériel, veuillez lire
les consignes de sécurité suivantes avant toute utilisation. Ces instructions doivent être mises à disposition de toute personne souhaitant
utiliser et exploiter les produits Datapath.
Die folgenden Sicherheitsanweisungen dienen der Vermeidung von Schäden an Ihrem Datapath-Produkt und Verletzungen der Nutzer.
Bitte lesen Sie sie sorgfältig durch, bevor Sie Ihr Produkt in Betrieb nehmen. Diese Anweisungen sollten allen Personen zugänglich
gemacht werden, die mit der Nutzung und der Bedienung von Datapath-Produkten betraut sind.
Alimentation électrique
Stromversorgung
Tous les produits Datapath requièrent une alimentation électrique principale. Cette alimentation électrique doit être interrompue en cas
de mise à jour ou de relocalisation du matériel.
Alle Datapath-Produkte müssen an die Hauptstromversorgung angeschlossen werden. Die Stromversorgung muss unterbrochen
werden, wenn Geräte ausgetauscht oder an einer anderen Stelle platziert werden sollen.
Câbles
Kabel
Ne pas exposer les câbles à un liquide quelconque car cela pourrait provoquer un court-circuit susceptible d’endommager le matériel.
Ne pas placer d’objets lourds sur les câbles car cela pourrait causer des dommages et conduire éventuellement à des fils électriques
dénudés.
Kabel dürfen nicht mit Flüssigkeiten in Berührung kommen, da dadurch ein Kurzschluss und somit ein Schaden an dem Gerät ausgelöst
werden könnte. Stellen Sie außerdem keine schweren Objekte auf die Kabel, um Schäden und offen liegende stromführende Leitungen
zu vermeiden.
Ventilation
Lüftung
Tout matériel informatique doit être disposé dans un endroit bien ventilé. Veiller à ne jamais obstruer les orifices de ventilation du boîtier
de l’ordinateur ; sinon, il y a risque de surchauffe du système et votre matériel peut être endommagé.
Computerausrüstung sollte in einem gut gelüfteten Bereich aufgestellt werden. Die Lüftungslöcher am Computergehäuse müssen stets
freigehalten werden, um eine Überhitzung und somit einen Geräteschaden zu vermeiden.
Environnement de travail
Arbeitsumgebung
Le matériel doit être placé sur une surface de travail stable et solide, dans un environnement exempt de poussière et d’humidité et non
exposé à des variations extrêmes de températures. Ne pas placer de liquides (boissons chaudes/froides, etc.) près du matériel, car un
déversement accidentel pourrait causer de graves dommages.
Die Geräte sollten in einer staubfreien und trockenen Umgebung, in der keine extremen Temperaturänderungen zu erwarten sind, auf
einer stabilen Arbeitsfläche aufgestellt werden. In der Nähe der Geräte sollten keine Flüssigkeiten (heiße/kalte Getränke etc.) platziert
werden, die verschüttet werden und schwerwiegende Schäden anrichten könnten.
Gaz/Liquides inflammables
Gas/brennbare Flüssigkeiten
Le matériel électronique ne doit jamais être utilisé en présence de gaz ou de liquide inflammable ; cela pourrait entraîner une explosion
ou un grave incendie.
Elektronische Geräte sind nicht in Umgebungen zu verwenden, in denen Gas oder brennbare Flüssigkeiten vorhanden ist/sind und somit
Brand- und Explosionsgefahr besteht.
Fumée/odeurs inhabituelles
Rauch/ungewöhnliche Gerüche
Si vous constatez la présence de fumée ou d’odeurs inhabituelles émanant de votre ordinateur, éteignez-le et débranchez le système de
l’alimentation secteur. Dans ce cas, le système devra être confié à un technicien qualifié pour inspection. Une poursuite de son utilisation
risquerait de provoquer des blessures corporelles et des dommages matériels.
Schalten Sie das System aus und trennen Sie es von der Hauptversorgung, wenn von Ihrem Computer Rauch ausgeht oder dieser ungewöhnliche Gerüche abgibt. Lassen Sie das System anschließend von einem qualifizierten Techniker prüfen. Bei fortgeführtem Betrieb
besteht die Gefahr von Verletzungen und Sachschäden.
Entretien
Wartung
L’entretien doit impérativement être effectué par des techniciens compétents, toute carte enfichable Datapath physiquement endommagée est à retourner à Datapath pour réparation via la procédure Datapath RMA.
Wartungsarbeiten sollten nur von qualifizierten Technikern durchgeführt werden. Physisch beschädigte Plug-in-Karten von Datapath
sollten zur Reparatur unter Einsatz der RMA-Verfahren von Datapath an Datapath übergeben werden.
Élimination
Entsorgung
En fin de vie, tous les produits Datapath seront éliminés conformément aux législations et réglementations locales. Au Royaume-Uni,
veuillez contacter Datapath pour organiser l’élimination. Notre numéro d’enregistrement de Déchets d’équipements électriques et
électroniques : WEEE/AA0005ZR.
Am Ende ihrer Nutzungsdauer sollten Datapath-Produkte gemäß den lokalen Gesetzen und Bestimmungen entsorgt werden. Für
Nutzer in Großbritannien: Bitte kontaktieren Sie Datapath, um Vorkehrungen zur Entsorgung von Datapath-Produkten zu treffen.
Unsere WEE-Registrierungsnummer lautet WEEE/AA0005ZR.
Consignes de sécurité du montage sur bâti
Sicherheitsanweisungen zur Rack-Montage
Température
Temperatur
S’il est prévu d’installer les systèmes VSN1190 dans une enceinte fermée ou dans un bâti comportant plusieurs unités, l’installation
devra être effectuée de telle manière que le débit d’air requis pour la sûreté de fonctionnement du matériel ne soit pas compromis. La
température ambiante de fonctionnement de l’environnement du bâti doit être maintenue en-dessous de 35 degrés centigrades dans
toutes les conditions. Des dispositifs de refroidissement appropriés doivent être intégrés dans l’armoire de façon à garantir le maintien
de cette spécification.
Um einen sicheren Betrieb zu gewährleisten, muss ausreichend Luft zur Kühlung sichergestellt werden, wenn VSN1190-Systeme in
einem geschlossenen Rack-Aufbau oder einem Aufbau für mehrere Geräte installiert werden. Die Umgebungstemperatur in dem Bereich, in dem sich das Rack befindet, sollte stets unterhalb von 35° C liegen. Das Gehäuse sollte mit einer Vorrichtung zur angemessenen
Kühlung ausgestattet sein, sodass diese Spezifikation erfüllt werden kann.
Charge mécanique
Mechanische Belastung
Le montage du matériel doit être effectué de manière à exclure toute situation dangereuse pouvant provenir d’une charge mécanique
irrégulière.
Um Gefahrensituationen zu vermeiden, muss bei der Platzierung der Geräte in das Rack auf eine gleichmäßige mechanische Belastung
geachtet werden.
Surcharge du circuit
Schaltkreisüberlastung
Il convient d’apporter une certaine importance au raccordement du matériel au circuit de l’alimentation secteur et aux effets qu’une
surcharge de l’alimentation pourrait avoir sur une protection contre les surintensités ou les câbles d’alimentation. Vérifiez pour cela les
valeurs nominales sur les plaques d’identification du matériel.
Beim Anschluss der Geräte an die Hauptstromversorgung sollten die Auswirkungen berücksichtigt werden, die eine Überlastung der
Stromversorgung auf einen eventuell vorhandenen Überstromschutz oder Versorgungsleitungen haben könnte. In diesem Zusammenhang sind die Typenschilder der Geräte zu beachten.
Fiabilité de la mise à la terre
Zuverlässige Erdung
Veiller à une mise à la terre fiable de tout matériel monté sur bâti. Une attention particulière devra être accordée aux raccordements
d’alimentation autres que les raccordements directs au circuit de dérivation (utilisation de multiprises par exemple).
In Bezug auf in Racks montierte Geräte ist stets auf eine zuverlässige Erdung und insbesondere auf Versorgungsleitungen zu achten, die
nicht direkt an den jeweiligen Stromkreis angeschlossen sind (Nutzung von Steckerleisten etc.).
Batteries remplaçables
auswechselbare Batterien
Attention: Risque d’explosion si la batterie est remplacée par un type incorrect.
Achtung: Explosionsgefahr, wenn Batterie durch einen falschen Typ ersetzt wird.
Jetez les piles usagées conformément aux lois / réglementations locales et aux instructions du fabricant.
Entsorgen Sie gebrauchte Batterien entsprechend der örtlichen Gesetze / Vorschriften und Anweisungen des Herstellers.
3
Introduction
The VSN1190 wall controller is a highly expandable and flexible solution for video wall and multi-screen
display applications. The controller is optimised for operation with the latest generation of Datapath PCI
express graphics and video capture cards. The VSN1190 can also be used with the VSN1100X expansion
chassis.
The VSN1100X is a general purpose 11-slot PCIe expansion chassis that can be used with any host PC to
expand the number of available PCIe slots.
4
Unpacking
Your packing box should contain the following items:
•
•
•
•
•
•
•
The VSN1190 Chassis (Large systems may also include the VSN1100X expansion chassis)
Express11-G3 backplane (installed)
SBC3 (installed) (VSN1190 only)
Mouse (VSN1190 only)
Keyboard (VSN1190 only)
Cables and Adapters (See Quantity guide Fig. 1)
Software Installation Suite CD (VSN1190 only.) This CD contains all of the software required for the VSN1190,
including the drivers for the capture cards and the Wall Control application software.
• SBC documentation (VSN1190 only)
If there are any discrepancies, you should contact Datapath immediately.
Cables and Adapters - Quantity Guide
Fig.1
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
x 1 - optional. If requested this item may be installed inside the VSN1190
x2 per VisionRGB-E2S card. x1 per VisionRGB-E1S and VisionSD4+1 card
x1 per VisionRGB-E1S/E2S card. x1 per VisionSD4+1 card
x1 per VisionRGB-E1S/E2S card. x1 per VisionSD4+1 card
x2 per VisionHD4
x1 per SBC3
x1 per Expansion Chassis
x1 per VisionSD4+1 card
x4 per ImageDP4 graphics card (Optional - powered/non-powered cables)
x1 per VisionSD8
x2 for the RPSU
5
The VSN1190
Features – VSN1190
The VSN1190 is an industrial PC incorporating an 11 slot PCIe backplane. The switched fabric technology
provides 11 x8 lane PCIe slots implemented with x16 physical connectors, with each slot capable of
providing up to 8GB/s bi-directional bandwidth.
Each system includes the Datapath SBC3, a single board computer that features Dual Quad Core™ Xeon®
processor, up to 32GB of DDR3 memory and on-board graphics.
The flexibility of the Express11-G3 technology allows multiple backplanes to be connected via the optional
Gen3 expansion kit.
Fig.2
1 = Power
2 = PSU Alarm Reset
3 = Power LED
4 = HDD LED
5 = Reset Button
6 = USB Ports
7 = DVD +RW
8 = Removable Hard Drives
Fig.3
R1 = Power Switches (RPSU)
R2 = USB Ports
R3 = Ethernet Ports
R4 = VGA Output
6
Specifications
19” 4U Industrial PC chassis
Dimensions (approx) Length 500mm (incl handles, Height 177mm,
Width 481mm (incl mounting brackets)
SBC3- Intel® Dual Quad Core Xeon EC5549 chipset in LGA 1366
Package (VSN1190 only)
16GB DDR3 1333 non-EEC registered system memory with an
upgrade option of 32GB (VSN1190 only)
Express11-G3 PCIe back plane providing 11 x8 lane slots
Two 750GB removable SATA hard drives - Enterprise Grade (VSN1190
only)
One DVD/RW combo drive (VSN1190 only)
Two Gigabit Ethernet ports (VSN1190 only)
VGA output enabling connection to DVI/VGA using the cable
provided. (Can be used as a control screen) (VSN1190 only)
800 Watt Redundant PSU
Noise - 48.6dB(A) up to 67.9 db(A); Dependent on system
configuration and ambient temperature
Triple cooling fans with removable air filter
Includes keyboard and mouse (VSN1190 only)
Windows 7 64bit operating system (VSN1190 only)
Operating temperature: 0 to 35 Deg C
3 year warranty
Models
Code
VSN1190-RSPU
VSN1100X-RSPU
Description
Controller chassis with 800 Watt RPSU
Expansion chassis with 800 Watt RPSU
7
Software
Each VSN1190 shipped by Datapath is custom built. If cards are not pre-installed then installation of the
software is required. For information on software installation consult the relevant user manual contained
on the installation CD.
If you have ordered Datapath Wall Control-red software this will have been installed prior to shipment.
ImageDP4 Video BIOS
The Intel x86 based architecture limits the amount of legacy I/O space available in a system to 64KB.
Hardware which requires I/O access can be mapped into this 64KB area. An ImageDP4 requests 256 Bytes
of legacy I/O. Unfortunately any PCIe bridge will align this to a 4KB boundary and so the I/O space
allocated to each ImageDP4 is actually 4KB.
64KB ÷ 4kB gives an absolute maximum of 16 ImageDP4 graphics cards. However, other system devices
also require legacy I/O. Often the Network Devices will request some I/O space, and so might the USB
devices and on-board graphics. It is not unusual for there to be I/O space available for only 8 ImageDP4
graphics cards when installing them in a complex server class motherboard.
There are a number of different BIOS types in operation as the computer boots. The “System BIOS” is
resident on the motherboard and is responsible for starting up all the hardware and mapping in the
resources (like the I/O) so that they are available to the CPU. The “Video BIOS” is resident on the
graphics cards. It is responsible for booting the GPU and for informing the System BIOS which resources
will be required for the GPU to operate correctly.
The System BIOS requires an I/O enabled ImageDP4 if it is used as the boot device, i.e. it provides the
graphics output that displays the BIOS boot messages. However the Windows driver for the ImageDP4
has been designed so that it does not require I/O. We can therefore use two types of Video BIOS for the
ImageDP4, one which requests I/O (and which can be used as a boot device) and one which does not. This
allows us to increase the number of ImageDP4 cards which can be used in a system.
To find out more about how to choose the correct BIOS for your requirements and how to update the
BIOS for the ImageDP4, download a PDF from our website by clicking on the link below or select it from
the Read Me file on the Software Installation Suite CD supplied with your ImageDP4 card:
www.datapath.co.uk
8
Use of the SBC’s onboard graphics adaptor
Onboard Graphics Adaptor used as Control Screen
The VSN1190 is shipped with the BIOS configured to boot off the onboard graphics device. This output
can then be used as the control screen for a typical wall configuration.
To set the system to boot on the onboard graphics device enter setup from the boot screen by pressing
<F2> as prompted.
In the BIOS setup utility select:
Boot>Primary Display>Onboard VGA
Fig.5
Onboard Graphics Adaptor Disabled
If you do not require a control screen, then you should disable the integrated graphics as described below.
Connect a monitor to the onboard graphics device output and enter setup from the boot screen by
pressing <F2> as prompted.
In the BIOS setup utility select:
Boot>Primary Display>Onboard VGA
9
Fig.6
The system will then boot on an output from the graphics card identified first by the PCI Bus.
10
Hardware Installation
Your VSN1190 may have cards that require installation as cards may have been shipped separately.
To ensure your cards are installed correctly please consult the user manual for detailed instructions. All
user manuals can be located on the Software Installation Suite CD.
VSN1190 Backplane Layout
The VSN1190 is fitted with the Datapath Express11-G3 backplane. The backplane consists of:
•
•
One PICMG1.3 slot
Eleven x8 lane PCIe slot
Fig.7
PCIe Port Width
PICMG
SLOT 1
SLOT 2
SLOT 3
SLOT 4
SLOT 5
SLOT 6
SLOT 7
SLOT8
SLOT9
SLOT10
SLOT11
X8
X8
X8
X8
X8
X8
X8
X8
X8
X8
X8
X8
11
Express11-G3 Connectors
FAN1,
FAN2,
FAN3
4 pin fan speed control header
Pin 1 : GND
Pin 2 : +12V
Pin 3 : TACH
Pin 4 : PWM
J30,
J31
SATA 2.0
Pin 1 : 0V
Pin 2 : A+
Pin 3 : APin 4 : 0V
Pin 5 : BPin 6 : B+
Pin 7 : 0V
FAN5,
FAN6,
3 pin fan header (non speed control)
Pin 1 : GND
Pin 2 : +12V
Pin 3 : N/C
J33
2 pin fan header (non speed control)
Pin 1 : GND
Pin 2 : +12V
J17
Panel Power Pushbutton Connector
Pin 1 : PWRBUT
Pin 2 : 0V
J38
USB 2.0
Pin 1 : +5V
Pin 2 : +5V
Pin 3 : USB1N Pin 4 : USB0N
Pin 5 : USB1P Pin 6 : USB0P
Pin 7 : 0V
Pin 8 : 0V
Pin 9 : N/C
Pin10 : N/C
J18
Panel Reset Pushbutton Connector
Pin 1 : SHB_RST
Pin 2 : 0V
J40
JTAG
Pin 1 : TCK
Pin 3 : TDO
Pin 5 : TMS
Pin 7 : N/C
Pin 9 : TDI
J19
Panel LED Connector
Pin 1 : LED Anode
Pin 2 : LED Cathode
J42
Debug + PLX I2C
Pin 1 : SCL
Pin 2 : 0V
Pin 3 : SDA
Pin 4 : N/C
Pin 5 : N/C
Pin 6 : N/C
Pin 7 : N/C
Pin 8 : N/C
Pin 9 : N/C
Pin10 : 0V
J23, J24 ATX Power Connector
Pin 1 : +3.3V
Pin13 : +3.3V
Pin 2 : +3.3V
Pin14 : -12V
Pin 3 : 0V
Pin15 : 0V
Pin 4 : +5V
Pin16 : PS_ON#
Pin 5 : 0V
Pin17 : 0V
Pin 6 : +5V
Pin18 : 0V
Pin 7 : 0V
Pin19 : 0V
Pin 8 : PWR_ON Pin20 : N/C
Pin 9 : +12V
Pin21 : +5V
Pin10: +12V
Pin22 : +5V
Pin11 : +12V
Pin23 : +5V
Pin12 : +3.3V
Pin24 : 0V
J49
PLX Debug Speed Select
Pin 1-2 : All slots Gen 1
Pin 2-3 : All slots Gen 3
J25, J26 AUX Power Connector
Pin 1 : 0V
Pin 5 : +12V
Pin 2 : 0V
Pin 6 : +12V
Pin 3 : 0V
Pin 7 : +12V
Pin 4 : 0V
Pin 8 : +12V
J50
GPIO
Pin 1 : GPI
Pin 2 : 0V
Pin 3 : GPO
J29
PLX EEPROM Select
Pin 1-2 : EEPROM A - U13
Pin 2-3 : EEPROM B - U14
12
Pin 2 : 0V
Pin 4 : +3V
Pin 6 : +3V
Pin 8 : TRST
Pin10 : 0V
Connecting Expansion Chassis (VSN1100X)
It is possible to connect a VSN1100X expansion chassis to the VSN1190 thereby increasing the number of
PCIe slots available.
The following diagram illustrates how this can be achieved:
Fig.7
The flexibility of the Express11-G3 technology allows multiple backplanes to be arranged in a star
configuration, providing the ability to create very large systems comprising several chassis each with 11
available slots for video capture inputs and/or graphics outputs, connected via the optional Gen3
expansion kit.
Connect the chassis by installing HLink-G3 and SLink-G3 cards in the VSN1190 and VSN1100X and
connecting the two cards using the Ex-Cable-G3.
The HLink-G3 and Slink-G3 cards are factory installed into a system as a pair. When connecting
expansion chassis ensure that the pair labelled Link1 are connected using the ExCable-G3, the pair
labelled Link2 are connected together and so on. In the event that this is not possible, connect the
expansion chassis to the host machine and re-install the Datapath Driver Install to reset the pairings.
Fig.10: ExCable-G3
Fig.8: HLink-G3
Fig.9: ExCable-G3
When connecting a VSN1100X expansion chassis to a VSN1170 machine the HLink-G3 card in the VSN1170
must be installed in one of the x8 slots. The SLink-G3 card in the VSN1100X should be installed in the
PICMG1.3 SBC slot.
Connect the HLink-G3 and SLink-G3 cards using the ExCable-G3.
13
VSN1190 LED’s
The VSN1190 and VSN1100X have an LED for each PCIe slot and the PICMG1.3 SBC slot.
Fig.11
Express11-G3 LED’s
The Express11-G3 has an LED for each PCI Express slot and the PICMG1.3 SBC slot. The LED’s indicate the
following:
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
D24
ON = +12V supply present
ON = +3.3V supply present
ON = +5V supply present
ON = +5V Standby supply present
ON = PICMG link speed = G3, FLASH-FAST = G2, FLASH-SLOW = G1
ON = PCIe Slot 1 link speed = G3, FLASH-FAST = G2, FLASH-SLOW = G1
ON = PCIe Slot 2 link speed = G3, FLASH-FAST = G2, FLASH-SLOW = G1
ON = PCIe Slot 3 link speed = G3, FLASH-FAST = G2, FLASH-SLOW = G1
ON = PCIe Slot 4 link speed = G3, FLASH-FAST = G2, FLASH-SLOW = G1
ON = PCIe Slot 5 link speed = G3, FLASH-FAST = G2, FLASH-SLOW = G1
ON = PCIe Slot 6 link speed = G3, FLASH-FAST = G2, FLASH-SLOW = G1
ON = PCIe Slot 7 link speed = G3, FLASH-FAST = G2, FLASH-SLOW = G1
ON = PCIe Slot 8 link speed = G3, FLASH-FAST = G2, FLASH-SLOW = G1
ON = PCIe Slot 9 link speed = G3, FLASH-FAST = G2, FLASH-SLOW = G1
ON = PCIe Slot 10 link speed = G3, FLASH-FAST = G2, FLASH-SLOW = G1
ON = PCIe Slot 11 link speed = G3, FLASH-FAST = G2, FLASH-SLOW = G1
ON= PLX Fatal Error
ON = PSU FAULT
14
Filter Maintenance
The system filter is an integral part of the wall controller and as such it needs to be maintained correctly.
Failure to maintain the filter can result in the system overheating and causing it to fail. In normal
operating conditions the filter should be removed and cleaned every 3 months. However, this 3 month
period is a guide only and it can be increased to every 6 months or decreased to one month depending on
the levels of dust in the environment the system is operating in.
It is recommended that the condition of the filter is checked at regular intervals.
The filter can be removed and cleaned whilst the system is in operation, system shutdown is not
necessary.
Note:
Failure to maintain the system filter could result in damage to your system and invalidate the
warranty.
Remove the Filter
Open the front panel door and locate the filter housing screw, remove the screw and lift the filter housing
away from the front panel.
Filter Housing Screw
Filter Housing
Filter
Remove the filter from the housing and shake it to remove any dust particles, this should not be done in
close proximity to the system to avoid dust ingress. Ideally, the filter should be cleaned using a vacuum
cleaner.
Note: The filter should never be immersed in water or any other cleaning liquid.
For advice on replacement filters, please contact Datapath Ltd.
15
Datapath Limited
Datapath has a long and very successful history in the computer graphics industry. Datapath has been
designing and supplying high performance, high quality graphics display systems to the world’s largest
and most demanding companies and institutions since 1982. Datapath was one of the founding
companies of multi-screen Windows acceleration using single and multi board solutions. Now using the
very latest display technology Datapath offers some of the world’s leading multi screen graphics
accelerators for the most demanding applications.
As new technology advances, so we at Datapath improve the performance and functionality of both our
hardware and software to give our customers more. Following a continuous development program, we
pride ourselves on our support and responsive nature towards all our customers and their changing needs.
As more sophisticated equipment and techniques become readily available, so we are there to exploit the
power and potential that this technology presents.
Technical Support
Registered Users can access our technical support line using, email, and the Support page on the Datapath
Web Site, usually with a response within 24 hours (excluding weekends).
Via Email
Send an email to support@datapath.co.uk with as much information about your system as possible. To
enable a swift response we need to know the following details:
Specification of the PC - including processor speed
Operating System
Application Software
Datapath Hardware / Software
The exact nature of the problem - and please be as specific as possible.
Please quote version and revision numbers of hardware and software in use wherever possible.
Copyright Statement
© Datapath Ltd., England, 2014
Datapath Limited claims copyright on this documentation. No part of this documentation may be
reproduced, released, disclosed, stored in any electronic format, or used in whole or in part for any
purpose other than stated herein without the express permission of Datapath Limited.
Whilst every effort is made to ensure that the information contained in this on-line help is correct,
Datapath Limited make no representations or warranties with respect to the contents thereof, and do not
accept liability for any errors or omissions. Datapath reserves the right to change specification without
prior notice and cannot assume responsibility for the use made of the information supplied. Datapath
Limited acknowledges all registered trademarks used within this documentation.
16
UK Headquarters and Main Sales Office
Datapath Ltd.,
Bemrose House, Bemrose Park, Wayzgoose Drive
Derby, DE21 6XQ, UK
Tel: +44 (0) 1332 294441
Fax: +44 (0) 1332 290667
Email: sales@datapath.co.uk
www.datapath.co.uk
17
Index
A
O
Adapters 5
Onboard Graphics 9
B
operating system 7
Backplane Layout 11
P
BIOS setup 9
packing box 5
C
power supply 3
cable 3
S
Cables 5
Safety Instructions 3
Connectors 12
SBC3 7
Copyright 15
Software 8
D
System BIOS 8
Dimensions 7
T
E
technical support 15
Email 15
V
Expansion chassis 4, 13
Video BIOS 8
Express11-G3 6
VSN1100X expansion 13
F
W
Features 6
Warranty 7
Filter Maintenance 15
I
Introduction 4, 16
L
LED’s 14
M
Maintenance 3
Models 7
Multi-unit rack assembly 3
18
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising