concord ultimax.3
Concord GmbH
Industriestraße 25
95346 Stadtsteinach
Germany
Phone +49 (0)9225.9550-0
Fax +49 (0)9225.9550-55
[email protected]
www.concord.de
Einbau- und Bedienungsanleitung
Instructions for attachment and use
Directives d‘installation et mode d‘emploi
Instrucciones de montaje y de uso
Istruzioni per l‘uso e il montaggio
Manual de montagem e de utilização
Inbouw- en bedieningshandleiding
Bruksanvisning og monteringsveiledning
DEUTSCH
ENGLISH
FRANÇAIS
ESPAÑOL
ITALIANO
PORTUGUÊS
NEDERLANDS
NORSK
DANSK
SUOMI
01
19
37
55
73
91
109
127
145
163
Kindergewicht
child‘s weight
0 - 18 kg
0 - 18 kg
ca. Alter
approx. age
0 - 4 Jahre
0 - 4 years
ECE Gruppen
ECE groups
0+ und I
0+ and I
ISOFIX Gruppen
ISOFIX groups
D und A
D and A
Monterings- og betjeningsvejledning
Kiinnitys- ja käyttöohjeet
UMI 05/0714 . IM 1710 ,00
_DEUTSCH
_ENGLISH
_FRANÇAIS
_ESPAÑOL
_ITALIANO
_PORTUGUÊS
_NEDERLANDS
_NORSK
_DANSK
_ SUOMI
Norm ECE R44 04
standard ECE R44 04
norme ECE R44 04
norma ECE R44 04
szabvány ECE R44 04
01
A
02
03
04
07
08
05
06
15
B
09
10
11
06
09
12
13
14
_ENGLISH
IMPORTANT NOTES
OVERVIEW
USING THE ULTIMAX CHILD CAR SEAT
GENERAL GUIDELINES
FOR ISOFIX-SUITABLE VEHICLES
REMOVING THE SEAT
MOUNTING THE CONCORD ULTIMAX
MOUNTING THE SEAT OPPOSITE TO THE DRIVING DIRECTION
(FROM BIRTH TO 13 KG)
MOUNTING THE SEAT IN THE DRIVING DIRECTION (FROM 9 TO 18 KG)
SECURING YOUR CHILD IN THE CONCORD ULTIMAX
REMOVING THE CONCORD ULTIMAX
USING THE TILT ADJUSTMENT
REMOVING / ATTACHING THE COVER
REMOVING THE PELVIC INSERT
CARE INSTRUCTIONS
WARRANTY CONDITIONS
20
22
22
23
23
24
25
26
28
30
32
33
34
35
35
36
19
_IMPORTANT NOTES
CAUTION!
Make sure you observe the relevant instructions in the user manual
of your vehicle before transporting children. Take particular note of
all information provided for the use of child seats in connection with
airbags.
WARNING!
•Children often carry small objects (e.g. toys) in jacket or trouser
pockets, and may also wear clothes with rigid components (e.g. belt
buckle).
Make sure that these objects are not clamped between the child and
the safety harness, as this might cause unnecessary injuries in case
of an accident. The same hazards also apply for adults!
•Naturally young children are often lively. Make sure to explain the
importance of safety when in a vehicle. Your child will then understand
that the harness lock should not be opened and the harness should
not be moved, giving you more peace of mind.
•Your child‘s safety can only be guaranteed if the safety system is
installed and used in accordance with the instruction manual.
•All system harness straps must be worn taut and without any twists,
and must be protected from damage.
•Protect any parts of the restraint system not covered with fabric
against direct sunlight to prevent your child from suffering burns.
•The child restraint system must not be damaged or crushed by
moving parts in the vehicle or by the vehicle doors.
•Do not attempt any modifications to the restraint system as they might
endanger your child‘s safety.
•After an accident, the entire child restraint system must be replaced
or sent to the manufacturer for testing, along with an accident report.
•Make sure to instruct your passenger on how to remove the child
from its safety seat in case of an accident or danger.
•The lap belts of the harness system must be fitted as low down as
possible so that the child’s hips are held correctly.
•The child seat must not be used on seats with activated front
airbags. (Danger to life)!
20
•Never leave your child unsupervised in the car seat - whether
harnessed or not.
•Make sure you secure any luggage and loose items to reduce the risk
of injury in case of an accident.
•The manual must always be carried with the child safety seat.
•The use of any accessories or replacement parts is prohibited, and
non-compliance will result in the lapse of all warranty and liability
claims. This only excludes original accessories from CONCORD.
•The child safety seat is to be used with original seat covers only.
•If the restraint system is used extensively it is normal for the seat
covers and other parts to suffer varying degrees of wear, depending
on the duration and intensity of use, and they will then have to be
replaced. We can therefore not provide any blanket warranty beyond 6
months for wear parts.
•Please contact your specialist shop for baby and children‘s products
and the relevant section of department stores, your car accessory
specialist shop or a catalogue company for replacement parts. They
will have a complete product portfolio for CONCORD child seat
accessories to choose from.
•The child seat CONCORD ULTIMAX has been tested in crash
simulations for impacts of up to 50 km/h against a solid obstacle.
Test results are compliant with the international test standard ECE R
44 04, which is applicable for all tested child safety seat systems.
When used as intended and in compliance with the installation
and operating instructions, the child safety seat should prevent or
minimise injuries to children up to a body weight of 18 kg in case of
an accident, depending on the type and severity of accident.
•A child safety device does not replace responsible and careful
behaviour in road traffic.
21
_OVERVIEW
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
Headrest
Harness buckle
Central adjusting device
Central harness
Operating lever for the tilt adjustment mechanism
Unlocking device for the seat lock (with double switch)
Safety display seat lock
ISOFIX SYSTEM control dial
Support leg operating button
Support leg
Front seat lock
Rear seat lock
ISOFIX SYSTEM unlocking button (left and right)
ISOFIX SYSTEM safety displays (left and right)
ISOFIX adapter
_GENERAL INFORMATION
• This is an ISOFIX child restraint. It has been approved for general use in
vehicles equipped with ISOFIX anchoring systems in compliance with ECE
regulation 44, change series 04.
• It is suitable for use in vehicles with ISOFIX-approved seats (see
documentation contained in the vehicle‘s operating manual) in accordance
with the relevant child restraint and anchoring category.
• This child safety restraint is compliant with the ISOFIX weight category: up to
18 kg and ISOFIX size categories: D and A
• If you have any questions or doubts, please contact the manufacturer of the
child safety unit or your retailer.
_USING THE CONCORD ULTIMAX CHILD CAR SEAT
_FOR ISOFIX SUITABLE VEHICLES
With the safety of your child in mind, you have decided to purchase our car seat
CONCORD ULTIMAX. The product is manufactured under strict quality control
conditions. Its optimum safety characteristics are only effective if the seat it used
as intended.
As a result you should ensure strict adherence with the mounting and usage
instructions.
The CONCORD ULTIMAX with ISOFIX system has been approved for ‚semi
universal‘ use, and is suitable for mounting on specific vehicle seats.
The CONCORD ULTIMAX is suitable for children up to the age of approx. 4 or
up to 18 kg. It is suitable for use in vehicles with ISOFIX-approved seats (see
documentation contained in the vehicle‘s operating manual) in accordance with
the relevant child restraint and anchoring category.
As a result of accident statistics, however, we recommend using the seat behind
the front passenger seat.
The appendix CAR FITTING LIST contains an overview of vehicles and vehicle
seats that have been approved for using the CONCORD ULTIMAX with ISOFIX
system in connection with a support leg.
Should your vehicle not be listed, please ensure that the CONCORD ULTIMAX can
be properly mounted in your car / on the desired seat before you purchase the
child seat!
Read the user manual provided by the manufacturer of your vehicle and the
mounting and security instructions contained in this user manual.
For latest updates, please visit: www.concord.de.
The seat consists of 2 parts: the seat (A) and ISOFIX base (B).
22
23
_ REMOVING THE SEAT
_ MOUNTING THE CONCORD ULTIMAX
The seat (A) of the CONCORD ULTIMAX can be removed from the ISOFIX-Basis
(B). Always remove the child first before removing the seat!
To make mounting easier, we recommend removing the seat (A) of the
CONCORD ULTIMAX from the base (B) (see „REMOVING THE SEAT“).
Move the tilt adjustment operating lever
(05) at the front of the seat upwards and
bring the seat into an upright position.
The unlocking mechanism of the seat lock (06) is
at the front underneath the seat on the top of the
ISOFIX base.
Pull the upper part of the lock (06) forwards and
push the lock down.
Always mount and remove the CONCORD ULTIMAX without a child in it!
Turn the ISOFIX SYSTEM (08) control dial on the front of
the CONCORD ULTIMAX ISOFIX base to the left until the
ISOFIX adapter (15) on the
reverse is fully extended.
Place the base in the direction of driving on a vehicle seat
equipped with ISOFIX receptacles.
Push the child seat backwards onto the ISOFIX receptacles until
the locking mechanisms of both ISOFIX adapters (15) audibly lock
into place and the safety displays (14) on both sides of the base
are green!
Lift the seat up off the base.
Now reinsert the seat, depending on the age of the child either in the driving
direction or opposite to it (see „MOUNTING THE SEAT OPPOSITE TO THE DRIVING
DIRECTION (FROM BIRTH TO 13 KG)“ or „MOUNTING THE SEAT IN THE DRIVING
DIRECTION (FROM 9 - 18 KG)“).
24
25
_ MOUNTING THE SEAT OPPOSITE TO THE DRIVING DIRECTION
(FROM BIRTH TO 13 KG)
Turn the ISOFIX SYSTEM (08) control dial to the right
until the CONCORD ULTIMAX lies as close/flush as
possible to the back rest of the car seat.
CAUTION!
Do not use on seats with
airbags. Danger to life!
Always mount the seat
without a child in it!
Guide the seat (A) as shown,
opposite to the driving
direction over the base (B).
First mount the frame of the
seat into the seat lock (12) of
the ISOFIX base.
CLICK
Then fold the seat forward until
the front seat lock (11) audibly
locks into the ISOFIX base and
the safety display (07) on the
top is green.
Push the release button (09) outward and position
the support leg (10) so that it rests securely on the
floor and the safety display shows GREEN.
Release the control button (09) to lock the support
leg in place.
CAUTION!
• Make sure that the seat is correctly
anchored to both anchoring points and
the safety display (07) is green!
• If the child‘s bodyweight exceeds
8 kg, the pre-installed pelvic insert
should be removed (see „REMOVING
THE PELVIC INSERT“).
26
CAUTION!
• The seat must be secured with the
ISOFIX SYSTEM even if no child is
travelling!
• Both ISOFIX adapters (15) must be
locked securely in place and the
safety displays (14) on both adapters
must show green.
• The support leg (10) must rest
securely on the floor and be locked
into place.
27
_ MOUNTING THE SEAT IN THE DRIVING DIRECTION
(FROM 9 - 18 KG)
Turn the ISOFIX SYSTEM (08) control dial to the right
until the CONCORD ULTIMAX lies as close/flush as
possible to the back rest of the car seat.
CAUTION!
Mounting in the driving direction is only permitted for babies which weigh
more that 9 kg and without the pelvic insert (see „REMOVING THE PELVIC
INSERT“).
Always mount the seat
without a child in it!
In vehicles with series-standard
headrests, a readjustment of
the headrest or its removal will
allow a better mounting position
of the car seat.
Guide the seat (A) as show,
in the driving direction over
the base (B).
First mount the frame of the
seat into the rear seat lock (12)
of the ISOFIX base.
CLICK
Then fold the seat forward until the front seat lock (11) audibly locks into
the ISOFIX base and the safety display (07) on the top is green.
Please remember to readjust or
replace the headrest in the
correct position if an adult is to
sit in that place instead.
Push the release button (09) outward and position
the support leg (10) so that it rests securely on the
floor and the safety display shows GREEN.
Release the control button (09) to lock the support
leg in place.
CAUTION!
CAUTION!
• Make sure that the seat is correctly
anchored to both anchoring points and
the safety display (07) is green!
28
• The seat must be secured with the
ISOFIX SYSTEM even if no child is
travelling!
• Both ISOFIX adapters (15) must be
locked securely in place and the safety
displays (14) on both adapters must
show green.
• The support leg (10) must rest securely
on the floor and be locked into place.
29
_ SECURING YOUR CHILD IN THE CONCORD ULTIMAX
The CONCORD ULTIMAX must be adjusted to the size of the child.
CAUTION
Check that the CONCORD ULTIMAX is mounted properly and that all belts have
proper tension, and also that all locking mechanisms are secure before each use.
At the front of the seat under the cover there is the
central adjusting device (03), which clamps the central
harness (04) tight. Loosen the central adjusting
device (03) by pushing the cap of the central adjusting
device up and pull the harness forward (do not pull
on the harness cushioning!).
Pull the head rest control, on the top edge, upwards
and move the head rest to the highest position (01).
Pull the head rest control, on the top edge, upwards and
move the head rest (01) to the suitable position for your
child.
The shoulder harness guide
should be situated slightly above
the child‘s shoulder. The shoulder
harnesses should lie in the middle
between the child‘s neck and the
outer edge of the shoulder.
Open the harness lock (02) and move the
harnesses to the sides and forward.
Place your child as far back into the seat as possible.
Bring the shoulder/lap harnesses and the central
harness together in front of the child and close the
harness lock.
Check that the harness lock (02) has latched shut
correctly. Ensure that none of the harness straps
are twisted.
30
Tighten the harness by pulling the central harness (04)
until it lies snug against the child‘s body.
CAUTION!
• The harnesses must not be twisted.
• The harness lock (02) must be closed properly and the harnesses must lie
snug against the child‘s body.
• The headrest/harness guide must be adjusted to the size of the child and
latched securely in place.
31
_ REMOVING THE CONCORD ULTIMAX
_ USING THE TILT ADJUSTMENT
To make the removal of the CONCORD ULTIMAX easier we recommend you first
remove the seat (A) (see „REMOVING THE SEAT“).
Always mount and remove the CONCORD ULTIMAX without a child in it!
Move the tilt adjustment operating lever (05) at the front of the seat upwards and
bring the seat into the desired position.
Push the release button (09) outward and move the
support leg (10) into its top-most position.
By releasing the lever (05) the seat is locked.
Turn the ISOFIX SYSTEM (08)
control dial on the front of the
CONCORD ULTIMAX ISOFIX base to
the left and move the base forward.
Push the ISOFIX SYSTEM unlocking buttons
(13), on the left and right of the base, so that
the ISOFIX adapters (15) are released from the
receptacles and the base springs forward.
Lift the CONCORD ULTIMAX out of the car seat.
Turn the ISOFIX SYSTEM (08) control dial to the right
until the ISOFIX adapter (15) is fully extended.
32
33
_REMOVING / ATTACHING THE COVER
_REMOVING THE PELVIC INSERT
To remove the cover the seat (A) has
to be removed from the base (B) (see
„REMOVING THE SEAT“).
If the child‘s bodyweight exceeds 8 kg,
the pre-mounted pelvic insert should be
removed.
This can be found in a pocket under the
seat, on the reverse of the seat cover.
Loosen the rubber bands and push buttons
of the cover, which are located in the
places marked red on the reverse side of
the cover.
Open the harness lock (02).
First remove the cover from the head
support (01).
Thread the harness lock (02) through
the harness lock cushioning and out
underneath the cover.
Open the Velcro fastener on the
harness guides and remove the cover
from the seat.
The covers are attached in reverse
order.
_CARE INSTRUCTIONS
Light dirt can be easily removed with a damp cloth. The cover can also be
removed and washed at 30°C. Remove the back cushion from the cover of the
head support before you wash it.
The cover material colour may run slightly when wet, in particular during
washing.
Do not use solvents on the cover!
Check that all the locks are closed and all anchorings are correctly
fastened.
34
35
_WARRANTY CONDITIONS
The warranty period begins at the time of purchase.
The warranty period granted is compliant with the legal warranty period in
the country of purchase. In terms of content, the warranty covers rework,
replacement delivery, or a rebate as the manufacturer sees fit.
The warranty applies only for the original user. In case of a fault, warranty rights
will be applicable only if the dealer, where the item was purchased, is notified
immediately after initial detection. Should the dealer be unable to remedy the
issue, then the product will be returned to the manufacturer with a detailed
description of the fault, and with the official purchase document including the
date of purchase.
The manufacturer shall not accept liability for faulty products not delivered by
him.
Warranty claims are void if:
• the product was modified.
• the product is not returned complete and accompanied by the original
purchase document to the dealer within 14 days of the detection of the fault.
• the fault occurred due to inappropriate handling or maintenance, or due
to other actions that are the fault of the user, specifically where the user
instructions were not complied with.
• repairs on the product were carried out by third parties.
• the defect was caused by an accident.
• the serial number has been damaged or removed.
Modifications to or deterioration of the product caused by the contractually
agreed use of the item (normal wear and tear) will not be accepted as a warranty
claim.
Any services rendered by the manufacturer in case of a warranty claim shall not
extend the warranty period.
36
D // Um die Funktionsfähigkeit und Sicherheit Ihres Kinderautositzes auch nach dem Austausch von Ersatz- und
Zubehörteilen zu gewährleisten, bitten wir Sie bei Bestellungen Ihrem Fachhändler nachstehende Angaben mitzuteilen:
EN // To ensure the functionality and safety of your child’s car seat after replacing spare and accessory parts, please
provide your dealer with the following details when placing your order:
F // Dans le but d’assurer le bon fonctionnement et la sécurité de votre siège auto enfant, également en cas de
remplacement de pièces de rechange et accessoires, nous vous prions de bien vouloir, en cas de commande, donner
les renseignements suivants à votre revendeur :
E // Para seguir garantizando el correcto funcionamiento y la seguridad de su asiento para niños después del cambio
de piezas o accesorios, le rogamos que indique los siguientes datos al realizar pedidos a su comercio especializado.
I // Quando trasmette un ordine al Suo rivenditore di fiducia, La preghiamo di comunicargli i dati seguenti per garantire
la funzionalità e la sicurezza del Suo seggiolino per bambini anche dopo la sostituzione di parti di ricambio e di
accessori.
CONCORD
ECE-Nr.
ECE No.
N° ECE
Número ECE
N° ECE
Serien-Nr.
Serial No.
N° de série
Número de serie
N° di serie
Ersatzteil
Spare part
Type de siège
Pieza de repuesto
Parte di ricambio
Fachhändler
Dealer
Revendeur
Comercio especializado
Rivenditore specializzato
Meine Anschrift
My address
Mon adresse
Mi dirección
Il mio indirizzo
Industriestraße 25
95346 Stadtsteinach
Made in Germany
semiuniversal
0 - 18 kg
1
E9
1
2
04. . . . . .
2 0000000000
P // Para garantir a funcionalidade e a segurança da cadeira de criança para automóvel depois da substituição de
peças sobressalentes e de acessórios, agradecemos o fornecimento dos dados seguintes à loja especializada aquando
de encomendas:
NL // Om de functionaliteit en de veiligheid van het door u gekochte autokinderzitje ook na vervanging van onderdelen
en accessoires te waarborgen, is het belangrijk dat u bij de bestelling in uw speciaalzaak onderstaande gegevens
vermeldt:
N // Bilbarnesetet som du kjøpte, skal fungere riktig og gi optimal sikring også etter at reservedeler eller tilbehør er
byttet ut. Ved eventuelle bestillinger bervi deg derfor om å gi forhandleren følgende opplysninger:
DK // For at garantere at autostolen stadig er funktionsdygtig og sikker, også efter at der er blevet monteret reservedele
eller tilbehør, bedes De oplyse følgende til Deres forhandler ved bestillingen:
FIN // Lasten turvaistuimen toiminnan ja turvallisen käytön varmistamiseksi myös varaosien tai lisävarusteiden
asennuksen jälkeen anna jälleenmyyjälle seuraavat tiedot, kun tilaat osia:
CONCORD
Nº. ECE
ECE-nr.
ECE-nr
ECE-nr.
ECE-nro
Nº de série
Serie-nr.
Serienr.
Serienr.
Sarjanro
Peça
Type kinderzitje
Reservedel
Reservedel
Varaosa
Loja especializada
Speciaalzaak
Forhandler
Forhandler
Jälleenmyyjä
Meu endereço
Mijn adres
Min adresse
Min adresse
Oma osoite
Industriestraße 25
95346 Stadtsteinach
Made in Germany
semiuniversal
0 - 18 kg
1
E9
1
2
04. . . . . .
2 0000000000
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement