DRD8 v2 (Installation Instructions)

DRD8 v2 (Installation Instructions)
OPERATION
Tap once
Fade the load to its last-used level, switch ON
Tap twice
Full bright, switch ON
— — Press and hold
Tap once
— — Press and hold
Increase the present level, switch ON
Fade to 0%, switch OFF
Decrease the present level, switch OFF
When you
see in the
instructions,
touch the top
of the switch
as directed.
When you
see in the
instructions,
touch the
bottom of
the switch as
directed.
Power Fail Memory
After a power failure, all Miro devices automatically return to the state that they
were in immediately prior to loss of power.
Cleaning
Clean using a cloth dampened only with water and a little mild detergent.
Use of solvents or hydrocarbon-based cleaners may cause permanent damage.
Troubleshooting
During house ID binding, the LED is not flashing on some
wireless devices.
• If LED is solid green before initiating house ID binding:
The device already has another house ID. Reset it to the factory default so
that it can be bound to the desired house ID. Resetting to factory defaults is
described in the “I need to start over” issue.
• If LED is solid yellow after initiating house ID binding:
The device may be out of range of the initiating device. Add a MRR2G
Wireless Repeater to boost signal range.
During Group binding, all LEDs stop flashing before I get back to the
device to press .
The 5 minute group binding process timer may have expired. Restart
the binding process timer by repeating steps 1 and 2 of the procedure
you were using. Notice that the devices you previously included are
flashing yellow; simply finish the process from where you left off.
The device LED flashes red when I press
.
If house or room scene controllers are used in the house, the house or room
configuration may be locked. Consult the installation instructions for the DRD5
or MRH5G wireless house scene controller if one is present. See the DRD6
or MRH6G wireless room scene controller instructions if one is present.
I made a configuration mistake. I need to start over.
To reset any Miro wireless device to factory default settings, press and
hold — — until the LED changes to solid yellow (approximately 10 seconds).
During the process, the LED flashes yellow. When complete,
it becomes solid yellow. The device can then be
reconfigured, exactly like any new device.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• C
onnect the equipment in an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
Warranty Information
Manufacturer warranties its products to be free of defects in materials and
workmanship for a period of five (5) years. There are no obligations or liabilities
on the part of manufacturer for consequential damages arising out of, or
in connection with, the use or performance of this product or other indirect
damages with respect to loss of property, revenue or profit, or cost of removal,
installation or reinstallation.
Legrand Customers contact:
Vantage Customers contact:
Please
Recycle
301 Fulling Mill Road Suite G.
Middletown PA 17057
Phone: 800.321.2343
www.legrand.us/onq
07480r2
9/2007
IS-0515
1061 South 800 East
Orem, UT 84097
Phone: 800.555.9891
www.vantagecontrols.com
Specifications
Voltage ........................................................ 120/277VAC, 60Hz
Operating Temperature................. 32°F to 104°F (0°C to 40°C)
Patents pending
Installation Instructions
DRD8 v2
Wireless Multilocation Controller
UNIT DESCRIPTION
The Miro Decorator DRD8 Wireless Multilocation Controller is used together
with Miro Decorator wireless devices to control lighting or appliance loads from
multiple locations. The DRD8 can be used in a group with the following Miro
Decorator devices:
DRD2
Wireless Incandescent Dimmer
DRD3
Wireless Switch
DRD4
Wireless Universal Dimmer
DRD9
Wireless Fan Control
MRP6W Wireless Plug-In Lamp Module
MRP7W Wireless Plug-In Appliance Module
Load Types
The DRD8 has no direct connection to the load. See the installation instructions
or specifications for the device connected to the load to determine compatibility
with those devices.
Miro Wireless
Miro wireless devices use radio signals to communicate with each other
to control lighting and other types of electric loads in selected areas. They
use the 900MHz band for high-speed control communication. Using the patented
“frequency-agile” Top Dog™ technology, Miro wireless devices avoid interference
with other 900MHz devices, such as cordless phones and baby monitors.
Application Assistance
The Miro Installation Guide provides more information about configuring scenes
and presets. Instructions for installation and use are included with
the relevant Miro wireless devices. Application support information and the Miro
Installation Guide is available on-line.
INSTALL IN COMPLIANCE WITH ALL APPLICABLE
CODES & STANDARDS.
Failure to follow these instructions may cause
personal injury or equipment damage.
CAUTION
Turn the power off at the circuit breaker
before installing the Controller.
 Installation
For ease of installation, manufacturer recommends use of a deep wall box. The
device is equipped with flying leads to simplify installation, however, if desired,
they may be removed by loosening the screw terminals.
1. Disconnect power to circuit by turning circuit breaker OFF before installation.
2. Remove existing wall plate and switch.
3. Strip existing wires 1/2”. If two wires will be connected to the same terminal
on a Miro device, both wires must be the same gauge (12AWG or 14AWG).
4. Wire the LINE (black), NEUTRAL (white) and GND (green or bare) supply wires
to the correspondingly marked terminals, according to the wiring diagram
below.
5. Attach the wall plate.
6. Switch the circuit breaker ON.
7. Make sure the LED on the DRD8 controller is lit. It should be yellow; if not, see
TROUBLESHOOTING.
NEUT
GND
LINE
SUPPLY
WIRES
Set House ID
All Miro wireless devices installed in the same home must acquire the same
unique House ID before use. This process is known as house binding. Each Miro
wireless device is bound to all other Miro wireless devices in the house.
New Installation
1. With all devices installed and energized, make sure that every Miro wireless
device LED is yellow. If any LED is off, be sure the circuit breaker is on and the
device is correctly installed.
When you see
on any device paddle until
2. Press
in the instructions,
the LED flashes yellow (about 2
firmly press and
seconds). This indicates that it has
hold both the top
acquired a unique House ID.
and bottom of the
3. Make sure that all other Miro
device paddle until
wireless device LEDs are flashing
the LED changes
green, indicating that they have
(about 2 seconds).
acquired the same House ID.
4. Return to the device used in step 2, which is still flashing yellow. Press
until the LED changes to solid green (about 2 seconds). All device LEDs in the
House change to solid green, indicating house binding is complete.
Adding a Device to an Existing Installation
If you’re adding or replacing a device in a Miro wireless installation that is already
operating, the new device must be bound to the same House ID as the other Miro
wireless devices in the house. After the new device is powered up, the LED should
be solid yellow. This indicates that it has not yet acquired a House ID. To acquire
the House ID for the existing system:
on any previously bound device until the LED flashes yellow (about 2
1. Press
seconds).
2. Verify that the newly added device LED is flashing green, indicating that it has
acquired the House ID.
3. Return to the same previously bound device used in step 1 and press
until
the LED changes to solid green (about 2 seconds). All device LEDs should now
be solid green.
Operation
Groups
Binding a Miro wireless device together in the same group with one or
more DRD8 controllers allows you to control the same device from multiple
locations. Devices that are bound in the same Group work in exactly the same
way, from any of the control locations.
You can include a variety of Miro wireless devices in the Group. Just remember
that all devices in the Group operate when one member operates. For example,
if you increase the brightness of one device in the Group, all devices will increase
brightness (switching devices turn ON).
Set the House ID (see Set House ID) before setting up Groups.
Set up a New Group
1. Go to any device that you want to include in the Group. Press . The device
LED flashes yellow, and all other devices in the House flash green.*
You now have 5 minutes to complete this process.
on the device until the
2. To include or exclude a device in the Group press
LED changes color. Yellow flashing LED = Included in the Group
Green flashing LED = NOT included in the Group
If you get to a device and it is NOT flashing, see TROUBLESHOOTING.
3. Return to the device used in step 1 and press
to terminate Group binding.
All LEDs revert to solid green. Now, all the devices in the Group control their
load circuit in exactly the same manner.
* If some devices flash yellow, a Group has already been set up that includes
those devices.
Adding a Device to a Group in an Existing System
1. Go to a device that is in the Group where you want to add the device.
until the device LED and all members of the Group flash yellow
Press
(about 2 seconds). The new device flashes green.
2. Press
on the new device until its LED flashes yellow (about 2 seconds).
3. Return to the device used in step 1 and press
. All LEDs are solid green.
REV. DESCRIPTION
INT:
REV. DATE
APPROVED
1 ECO# C01933
2 ECO# C02411
MJS
MJS
3/28/07
CG
TITLE BOX PAGE ONLY.
DO NOT MAKE FILM • DO NOT PRINT
• Print: 2-sides
• Ink Color: Black
• Paper: White 16lb (60g/m sq) uncoated
prefer recycled stock
• Final trim size: 16” (Wide) x 6” (High).
• Four (4) fold.
• Final folded size: 4” (Wide) x 6” (High).
4-FOLD
IF YOU HAVE ANY QUESTIONS REGARDING SPECIFICATIONS OR REQUIRE
ADDITIONAL FILE FORMATTING, PLEASE CONTACT Mary Jo Sowinski.
Phone: 408-486-7511
Email: maryjo.sowinski@Legrand.com
All information in this drawing is the property of Watt Stopper/Legrand and cannot be copied or
used without the written approval of Watt Stopper/Legrand.
Drawn by
SOWINSKI
PLM
SANTA CLARA, CALIFORNIA
MarCom
Engineering
Title: DRD8 v2 Installation Instructions
QA
TITLE BOX PG Scale: 1:1
Drawing #:
07480
Orig. Drawing Date: 16 MAR 07
Revision Date: 24 SEP 07
Rev. #:
2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising