Step 5. Configure start up wizard
1
Select the screen resolution from the drop-down menu based on your TV/monitor’s resolution.
Resolution
System Resolution: 1024 * 768/60HZ
2
If you reboot your system and want the wizard to start again check this box.
Wizard
Start wizard when device starts?
3
We strongly recommend that you change the default
Admin password ‘12345’ for better security protection.
Wizard
Admin Password *****
New Admin Password
New Password
Confirm
4
Select the applicable time zone, date/time format, and time.
Wizard
Time Zone
Date Format
System Format
System Time
(GMT+08:00) Beijing, Urumqi, Singapore
MM-DD-YYYY
09-29-2014
18:14:37
5
We recommend checking ‘Enable DHCP’ even if your DVR is not connected to the internet, this will automatically get the DVR
IP address.
Wizard
NIC Type 10M/100M Self-adaptive
Enable DHCP
IPv4 Address 192.0.0.64
6
The wizard will show additional network information, click ‘Next’ to proceed.
Wizard
Server Port 8000
HTTP Port 80
RTSP Port 8554
7
To initialize the hard drive click the ‘Init’ box otherwise the
DVR will NOT record.
Capacity
Wizard
Status Property Type Free Space
1 Normal R/W Local 464GB
8
If you wish to add an IP camera click ‘Search’ otherwise, click ‘Next’ to proceed.
Wizard
IP Address Amount Model
1 192.168.1.36
1 CMIP3412
9
Choose continuous or motion detection recording from the listed options. Check the ‘Start Recording’ box to initialize recording.
Click ‘Ok’ to finish the wizard.
Wizard
Start Recording
Continuous
Motion Detetction
1 DVR Power Adapter
What is in the box?
1 HD-TVI Digital Video Recorder
4 720p Analog Cameras
4 90ft. Siamese BNC Cables
1 1-to-4 Power Splitter
1 Mouse
1 Remote Control
1 DVR Power Adapter
1 Camera Power Adapter
1 Quick Start Guide
1 Warranty Card
2 Security Stickers
1 2 3 5
4 5 6 7 8 9 10 11 12
1 Power LED Indicates if the DVR is powered on
2 Status LED Indicates if the Hard Drive is working
3 Tx/Rx LED Indicates if the Network is active
4 Video In Connects cameras via BNC cables
5 USB Port Connects to a USB mouse or flash drive
6 HDMI Port Connects to HDTV or computer monitor
7 VGA Port Connects to TV or computer monitor
8
9
Audio I/O Connects an extra microphone/speaker
(not included)
LAN Connects to your router
10 RS-485 Connection for additional PTZ camera
(not Included)
11 12V Connects the12V DC Power Supply
12 Power Power Switch
Troubleshooting
Problem
No display/No signal/Invalid format
No picture/No video
Possible Solution(s)
• Make sure the VGA/HDMI cable is properly connected to both the DVR and TV/monitor
NOTE: A laptop cannot be used as a screen
• Make sure your TV/monitor is on the correct video input (e.g. HDMI1, HDMI2, etc.)
• Try switching to another 1080p TV/monitor and adjust the output resolution in the DVR menu
• On the front of the DVR check that the power LED light is on
• Make sure the camera is completely connected to the power splitters well as the Video In plug
Cannot log in
Camera picture is not clear
Night vision is not working
DVR is not recording
• The default user name is: admin and the default password is: 12345. If you don’t remember your old password, please submit a ticket to us at www.laviewusa.com/contact/ .
• Make sure the camera is not placed behind a window, there is no interference or a strong light source in front of the camera
• In DVR Menu>Record>Parameter>Resolution, set the sub all channels stream resolution to CIF for
• Move the camera to a different location and/or direction
NOTE: The live view (sub stream) resolution is NOT the actual image quality recorded (Main stream); Connection of excessive length (over 200ft) of BNC cable will drop the camera image quality; Working at extreme weather condition (below -40F or above 140F) will drop the image quality and damage the camera.
• The infrared activates automatically when the environment is dark enough. You can check that the camera infrared bulbs are working properly as they turn light red in dark environments
• Check that the hard drive status is normal and is initialized under the Main
Menu>HDD>General
• Enable the record mode (Normal or Motion Detection) under the Main
Menu>Record>Schedule>Edit for the selected camera
HD-TVI
QUICK START GUIDE
Remote Viewing
View footage on your mobile devices with our app. You can either scan the provided QR code or search LaView Net in the app store.
LaView NET
SCAN ME
Content may vary by model, including the number of channels, cameras, configuration, and hard drive capacity.
Questions?
Call us at:
626-898-4988
(M-F from 9am to 6pm PST)
Open support ticket at: www.laviewusa.com/contact
Tutorial videos & user manual at: www.laviewusa.com/support
Copyright © LaView Eagle-Eye Technology Inc. 2015
