Assembly Instruction
CAUTION: Read instruction carefully and turn electricity off at main circuit breaker panel
before beginning installation.
ITEM#:CHA4008A
Care and Cleaning
To clean the outside of the fixture, use a dry or slightly dampened clean cloth(use clean water, never a solvent)to wipe the surface of the fixture.
To clear the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth(use clean water, never a solvent) to wipe the interior surface of the fixture
Do not use any cleaners with chemical, solvents or harsh abrasives. Use Only a dry soft cloth to dust or wipe carefully.
Estimated Assembly Time:30 minutes
Part List and Hardware List
PIECE DESCRIPTION PICTURE QUANTITY PIECE DESCRIPTION PICTURE QUANTITY
A Wire Nut 3X II Fixture Loop
1X
B Mounting Plate 1X J Chain 1X
C Bulb 4X K1 Top Frame 1X
2X K2 Bottom Frame 1X D
E
Mounting Screw
Canopy
F Hanging Loop
1X
1X
L Metal Cover
1X
1X
G Canopy Nut 1X
M
Socket Assembly
N Knurled Nut
4X
2X
H Closable link/cap
1 / 3
Installation
Step 1
Unpack all parts from cartons carefully.
Insert the power cord of the Socket Assembly(M) to the
Top Frame(K1),Metal Cover(L),Hanging Loop(I). Then fix the Top Frame(K1) by turning the Hanging Loop(I) clockwise till tight.
Step 2
Screw the Chain(J) to the Hanging Loop(F) and the Fixture Loop (I) with Closable link/cap (H) as diagram.
H
Step 3
Weave the 2 wire power cord and bare ground wire through every other loop to the top of chain(J),center holes of Hanging
Loop(F)&Canopy(E)&Mounting Plate(B) as diagram.
Insert the threaded tube of the Mounting Plate(B) into the center hole of the Hangling
Loop(F),rotate the Mounting Plate(B) clockwise till tight.
Slide the Canopy Nut(G) then the Canopy(E) to the end of the Chain(J).
L
K1
H
G
I
K1
M
G
H
K1
2 / 3
Step 4 Wire connection
Connect,Hot,Black or Red outlet Supply Wire to:
Black
*Parallel Cord(round&smooth)
Clear,Brown,Gold or Black without Tracer(colored stripes)
Insulated Wire(not green)with copper metal conductor
Connect,Neutral,White Outlet Supply Wire to:
White
*Parallel Cord(square&ridged)
Clear,Brwn,Gold or Black without Tracer(colored stripes)
Insulated Wire(not green)with Silver metal conductor
*Note: When parallel wire(SPTI&SPTII)is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth.(See illustration on left)
Grounding Instructions:
a) For installation in the United States: Wrap ground wire from outlet box around green
ground screw on mounting bracket, no less than 2" from wire end. Tighten ground screw. If
fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector.
b) For installation in Canada: If fixture is supplied with ground wire, wrap ground wire
around green grounding screw on mounting bracket. Tighten ground screw.
Step 5
Attach the Mounting Plate (B) onto the junction box by inserting two Mounting Screws (D) and turning clockwise till tight.
Slide the Canopy (E) upward along the chain(J) till the ceiling surface. Fix the Canopy(E) by rotating the
Canopy Nut(G)clockwise to engage it with the threaded portion of the Hanging Loop (F) until secure. Do not over tighten this nut.
Insert the bulbs(C) into the sockets(M) until secure. DO
NOT EXCEED THE SPECIFIED WATTAGE.
Attach the Bottom Frame(K2) to the Top Frame(K1), aligning the corned holes then fix it with Knurled
Nuts(N) clockwise till tight.
PLEASUE USE TYPE"B" BULB MAX 40-WATT
OR CFL BULB MAX 9-WATT OR LED MAX 9-WATT
THERE ARE 4 X 4W LED BULBS IN THE BOX.
I
A
B
J
D
F
E
G
K1
C
M
Step 6
Consult a qualified electrician to ensure correct branch circuit conductor
K2
N
ENJOY YOUR LAMP
3 / 3
