Allen-Bradley DL40 PLUS OFFLINE PROG.SFTWR User Manual

Allen-Bradley
Dataliner DL40 Plus
Offline Programming
Software
(Cat. No.2706-LSW)
User
Manual
Important User
Information
Because of the variety of uses for the products described in this
publication, those responsible for the application and use of this
control equipment must satisfy themselves that all necessary steps
have been taken to assure that each application and use meets all
performance and safety requirements, including any applicable laws,
regulations, codes and standards.
The illustrations, charts, sample programs and layout examples
shown in this guide are intended solely for purposes of example.
Since there are many variables and requirements associated with any
particular installation, Allen-Bradley does not assume responsibility
or liability (to include intellectual property liability) for actual use
based upon the examples shown in this publication.
Allen-Bradley publication SGI-1.1, Safety Guidelines for the
Application, Installation, and Maintenance of Solid-State Control
(available from your local Allen-Bradley office), describes some
important differences between solid-state equipment and
electromechanical devices that should be taken into consideration
when applying products such as those described in this publication.
Reproduction of the contents of this copyrighted publication, in
whole or in part, without written permission of Allen-Bradley
Company, Inc., is prohibited.
Throughout this manual we use notes to make you aware of safety
considerations:
!
ATTENTION: Identifies information about practices
or circumstances that can lead to personal injury or
death, property damage or economic loss.
Attention statements help you to:
• identify a hazard
• avoid the hazard
• recognize the consequences
Important:
Identifies information that is critical for successful
PLC and PLC–5 are registered trademarks of Allen–Bradley Co.
SLC is a trademark ofAllen–Bradley Co.
Windows, MS–DOS, and Windows NT are a trademarks of Microsoft Corporation.
Using this Manual
Preface
What You Need to Know . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents of this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conventions Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview of the DL40 Plus
Chapter 1
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Available Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Message Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller Support for Remote I/O . . . . . . . . . . . . . . . . . . . . . . . . .
Available Catalog Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Software
P–1
P–1
P–2
P–2
1–1
1–1
1–3
1–4
1–11
1–12
1–13
1–15
Chapter 2
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Personal Computer Requirements . . . . . . . . . . . . . . . . . . . . . . . . .
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installed Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Installation (without PassThrough) . . . . . . . . . . . . . . . . . . . .
Software Installation for DH+ PLC PassThrough . . . . . . . . . . . . . . .
Software Installation for Ethernet PLC PassThrough . . . . . . . . . . . .
Starting the Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Establishing Initial Non–networked Communications . . . . . . . . . . . .
2–1
2–1
2–1
2–2
2–2
2–3
2–3
2–4
2–5
2–11
2–13
2–13
Publication 2706-6.2
toc–ii
Table of Contents
Navigating the Software
Chapter 3
Starting the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Title Screen and Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu Control Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shortcut Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exiting the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Offline Operating Modes
Chapter 4
Develop Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
File Selection Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Create New File Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Path Directory Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Develop Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Messages Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Edit Message Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Message Text Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Create New Message Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Copy Messages Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delete Message Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Renumber Messages Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Text Search Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Modify Message Attributes Screen . . . . . . . . . . . . . . . . . . . . . . . .
Message Attribute Default Screen . . . . . . . . . . . . . . . . . . . . . . . . .
Options Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ports Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Verify Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Downloading/Uploading
Message Files
Publication 2706-6.2
3–1
3–2
3–3
3–4
3–6
3–6
3–7
4–2
4–4
4–5
4–6
4–7
4–8
4–9
4–10
4–16
4–17
4–19
4–20
4–22
4–24
4–32
4–34
4–36
4–39
4–44
Chapter 5
Transfer Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Downloading a File using RS-232 or RS-485 . . . . . . . . . . . . . . . . .
Uploading a File using RS-232 or RS-485 . . . . . . . . . . . . . . . . . . .
Downloading a File using Remote I/O (PassThrough) . . . . . . . . . . .
Uploading a File using Remote I/O (PassThrough) . . . . . . . . . . . . .
Creating a New Communications File . . . . . . . . . . . . . . . . . . . . . .
Modifying an Existing Communications File . . . . . . . . . . . . . . . . . .
Sending the Time and Date Using RS-232 or RS–485 . . . . . . . . . .
Writing a File to Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reading a File from Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5–2
5–3
5–6
5–8
5–10
5–12
5–16
5–17
5–18
5–20
Table of Contents
Getting Reports
Chapter 6
Reports Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Select File Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configure Ports Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting the Print Job . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Managing Message Files
toc–iii
6–1
6–1
6–2
6–3
Chapter 7
Files Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Select Files Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
File Selections/File Picks Window . . . . . . . . . . . . . . . . . . . . . . . . .
Copy File(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delete File(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rename File(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Convert DL20 File(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7–2
7–3
7–4
7–4
7–6
7–7
7–10
Appendix A – Message Display Worksheets
Appendix B – Cables
Appendix C – ASCII Character Sets
Appendix D – PLC-5 Data Pass-Through
Index
Publication 2706-6.2
Using this Manual
This preface provides an overview of the Dataliner DL40 Plus
Offline Programming Software. The topics it covers include:
•
•
•
•
What you need to know
Contents of the manual
Conventions used throughout the manual
Related publications
What You Need to Know
No special knowledge is required to read this manual or use the
DL40 Plus Offline Programming Software (Catalog No. 2706-LSW).
However, you should be familiar with the operation of the DL40
Plus and how it will be integrated into your control system before
trying to use the Offline Programming Software.
Contents of this Manual
This manual describes how to install and use the DL40 Plus Offline
Programming Software. The manual is organized as follows:
Chapter
1
Title
Overview of the DL40 Plus
2
Installing the Software
3
Navigating the Software
4
Creating Message Files
5
6
Downloading/Uploading
Message Files
Getting Reports
7
Managing Message Files
Appendix A
Appendix B
Appendix C
Message Display
Worksheets
Cables
ASCII Character Sets
Appendix D
PLC-5 Pass-Through
Purpose
Provides an overview of the DL40 Plus
Message Display.
Describes how to install the DL40 Plus
Offline Programming Software.
Provides a description of the menus
along with instructions for setting up and
exiting the software.
Describes how to create and manage
message application files.
Describes the contents and use of the
Transfer menu.
Describes the contents and use of the
Reports menu.
Describes the contents and use of the
Files menu.
Convenient forms for recording message
contents.
Cable pinout diagrams
Summary of ASCII characters and their
keyboard codes.
Provides an application example of using
PLC-5 data Pass-Through.
Publication 2706-6.2
P–2
Using this Manual
Conventions Used
The following conventions are used in this manual:
• All menus and screens reproduced in this manual approximate
what you see when using the software.
• A symbol or word in brackets represents a single key that you
press. These include keys such as [A] or [Del]. Since the
Dataliner can be programmed with a variety of keyboards or
terminals, the printing on your keyboard may be different from
the symbol or word indicated in brackets.
• This manual uses ↵ to specify the carriage return function of a
keyboard. On your keyboard this may correspond to an
[ENTER], ↵ , or [Rtrn] key.
• The up caret, ^, is the symbol for a control character. For
example: ^W is the symbol for a Control W character. On most
computers this character is entered by pressing [Ctrl] and [W]
simultaneously.
• In the following chapters, we refer to the Dataliner DL40 Plus
Message Display as the DL40.
Related Publications
Other publications to which you may want to refer include:
• Dataliner DL40 Plus Message Display User Manual,
(Publication 2706-6.1)
• Dataliner DL40 Plus Message Displays Release Note (provided
with DL40 Plus display) is helpful if you are replacing an existing
DL40 display with a DL40 Plus display.
Publication 2706-6.2
Overview of the DL40 Plus
Chapter Objectives
This chapter describes key features and capabilities of the DL40
Plus. Understanding the capabilities allows you to use the Offline
Programming Software more effectively. For more information,
refer to the DL40 Plus user manual (Publication 2706-6.1).
Section
Available Configurations
Page
Available Configurations
1–1
Message Support
1–3
Programming Features
1–4
Operating Modes
1–11
Special Messages
1–12
Controller Support for Remote I/O
1–13
Available Catalog Numbers
1–15
The DL40 Plus is available in a 2- or 4-line configuration (capable of
displaying 20 characters per line) with either Remote I/O or Parallel
port communication options.
Remote I/O Version
The Remote I/O version enables two-way communications with the
Allen-Bradley family of PLCs and SLCs. A remote I/O version of
the DL40 Plus can appear to the PLC or SLC as any size I/O rack
(1/4, 1/2, 3/4, or full).
Parallel Port Version
The Parallel Port version receives message number triggers, slave
addresses, and variable data from a PLC or SLC output module via
16 data lines and 4 strobe lines (indicating the type of data).
1–2
Overview of the DL40 Plus
RS-485/RS-232 Communications
Both the Remote I/O and Parallel Port versions have RS-485 and
RS-232 ports. You can configure these ports for Programmer, DL
Slave or Open Protocol communications (see table below). Port
settings are modified through the Ports menu in the Offline
Programming software or the Onboard Editor. You select a
communication option under the Port Use submenu.
The RS-232 port always communicates with the Offline
Programming Software regardless of the configured mode. Open
Protocol or DL Slave operation can occur on either the RS-232 or
RS-485 port.
If the RS-485 port is configured for Open protocol or DL Slave
operation, you cannot configure the RS-232 port for the same
protocol. Instead, an information message reports an invalid port
configuration (Incompatible Port Usage).
Communication/Printing Options
Configurations
Description
escription
DL40 Plus Port
1
Offline Programming
and Serial Printing
RS–485
RS–232
√
√
2
RS-232 Offline Programming
and RS-485 Message Triggering
RS–485
RS–232
√
3
RS-232 Offline Programming
RS-485 Slave Communications
RS–485
RS–232
√
4
RS-485 Offline Programming
RS-232 Message Triggering
RS–485
RS–232
5
RS-485 Slave Communications
RS-232 Message Triggering
RS–485
RS–232
6
RS-485 Offline Programming
RS-232 Slave Communications
RS–485
RS–232
7
RS-485 Message Triggering
RS-232 Slave Communications
RS–485
RS–232
Programmer
Open Protocol
Slave
Printing
√
√
√
√
√
√
√
√
√
√
√
√
√
Note: Open protocol is a serial ASCII based format for triggering
messages stored in the DL40 Plus displays. Open protocol supports
message triggers with or without variable data over the RS-232 or
RS-485 serial ports.
Publication 2706-6.2
Overview of the DL40 Plus
Message Support
1–3
The DL40 Plus stores messages of varying length. Each message is
identified by a unique message number from 1 to 9999. Messages
are placed in an internal memory queue when triggered by a
command from your control system. They are then run according to
attributes selected in the DL40 Plus.
The DL40 Plus can display a wide variety of characters and symbols,
including:
• Uppercase letters
• Lowercase letters
• Punctuation
• Special characters from the English extended ASCII character set
• English character set (default)
• International character set ISO 8859–1
• Cyrillic character set (Russian)
Note: English characters are also available with both the
International an Cyrillic character sets.
A person with normal vision can easily read the display from a
distance of up to 25 feet.
Publication 2706-6.2
1–4
Overview of the DL40 Plus
Programming Features
The DL40 Plus is a versatile status, prompt and diagnostic display
tool, equipped with a full range of high-end programming and
performance features.
Remote I/O
Version
Parallel Port
Version
Supports offline programming software
Yes
Yes
PLC-5 Remote I/O PassThrough via DH+
Yes
No
PLC-5E Remote I/O PassThrough via Ethernet
Yes
No
International and Cyrillic character sets
Yes
Yes
Onboard editing with PC keyboard
Yes
Yes
Send ASCII data to a PLC via a Remote I/O link
Yes
No
Send ASCII data to a device via an RS-485 link
Yes
Yes
Communicates with any programmable controller
No
Yes
Customizable historical events stack
Yes
Yes
Real-time clock operations
Yes
Yes
RS-232 and RS-485 ports
Yes
Yes
Debug Mode
No
Yes
Support for auxiliary devices such as slave displays
and printers
Yes
Yes
Background messages
Yes
Yes
Hidden messages
Yes
Yes
Embedded variables
Yes
Yes
Data mode selection
Yes
Yes
Message chaining
Yes
Yes
Adjustable parameters for serial communications
Yes
Yes
Adjustable display brightness
Yes
Yes
DL40 Plus Capabilities
Publication 2706-6.2
Overview of the DL40 Plus
1–5
Offline Programming Software
Create and edit application files using the Offline Programming
Software (Catalog No. 2706-LSW) on a personal computer. With
interactive menus you can quickly create messages, set message
attributes, and download messages to one or more DL40 Plus
displays.
Create Message editing screen
Download Message Files screen
Set Message Attributes window
Convert DL20 files for use with a DL40 Plus
The offline programming cable (Catalog No. 2706-NC13) provides a
direct connection between a personal computer running the Offline
Programming Software and a DL40 Plus. This 3-meter cable has a
9-pin, D-shell connector on each end.
Publication 2706-6.2
1–6
Overview of the DL40 Plus
International and Cyrillic Character Sets
The local language character sets let you create and display messages
in other languages such as French, German, Italian, and Spanish with
the Offline Programming Software with:
• English (default)
• International character set ISO 8859–1
• Cyrillic (Russian)
English characters are also available with both the International and
Cyrillic character sets.
Onboard Editor
With the Onboard Editor you can create or edit messages, select
message attributes, and set options and variable formats using a
standard IBM PC keyboard. The Keyboard port is located on the rear
panel of the DL40 Plus.
Send ASCII Data to a PLC via Remote I/O Link
Using Remote I/O communications, you can send ASCII data to a
PLC. Attach an IBM compatible keyboard to the DL40 Plus and you
can enter part numbers, badge numbers, passwords, and similar
information as required. The DL40 Plus processes and displays the
information, and then sends it to the controller.
You can establish similar communications over an RS-232 or
RS-485 link.
Communicate with any Programmable Controller
(Parallel Port Version)
The DL40 Plus accepts information from any programmable
controller over a total of 20 input lines (16 data and 4 strobe lines).
Parallel Port versions of the DL40 Plus have an isolated 12 VDC
supply output that can be used to power outputs that pull data and
strobe lines high.
Backup Operations
Archive DL40 Plus application files in the Offline Programming
Software (Catalog No. 2706-LSW) by uploading or downloading
files between a computer and DL40 Plus displays.
Publication 2706-6.2
Overview of the DL40 Plus
1–7
Historical Events Stack
The Historical Events Stack records the occurrence and sequence of
some or all messages and logs variable data values that have been
triggered and/or displayed. The 16K bytes of stack memory holds
about 1,000 events. You can view information in chronological order
or by frequency of occurrence, or print the record.
Clock Operations
A real-time battery-backed clock keeps accurate time even when
power is removed from the unit. The DL40 Plus can display the
current time and/or date in either AM/PM or 24-hour military
format.
Note: The date function is year 2000 compliant.
Date and time information can be displayed as part of any triggered
message, and passed on to a PLC. You can also date- or time-stamp
events as they are recorded in the Historical Events Stack.
Set the DL40 Plus internal clock using the front panel menus, a
keyboard connected to the Onboard Editor, a PLC/SLC, or the
Offline Programming Software.
RS-232 and RS-485 Ports
The DL40 Plus has both an RS-232 and RS-485 port.
Use the RS-232 port to:
• upload or download message files from a computer
• trigger messages via Open protocol (ASCII triggering)
• send messages to a single slave message display
• print messages and/or the contents of the Historical Event Stack
Use the RS-485 port to:
• multi-drop upload or download message files from a computer
• trigger messages via Open protocol (ASCII triggering)
• send messages to one or more slave message displays
• input ASCII data via bar code
Publication 2706-6.2
1–8
Overview of the DL40 Plus
Keyboard Port
Use the Keyboard port on the DL40 Plus to:
• edit options, messages, communication port settings
• input ASCII data to a host controller, PLC, or computer
• trigger messages using Open protocol (ASCII triggering)
Debug Mode (Parallel Port Version)
Use Debug mode to display the binary status (1 or 0 value) of the
data lines and the state of the strobe lines. This mode is useful for
checking the output of a programmable controller.
Auxiliary Devices
Connect a variety of useful auxiliary devices to the DL40 Plus
display.
Slave Displays
Address up to 126 DL40 Plus or DL50 slave displays over an
RS-485 network at distances up to 4,000 feet (1200 m) from the
originating DL40 Plus. You can also control the annunciation relay
on remote DL40 Plus or DL50 Series slave displays. By assigning a
specific address to each slave display, you can control which slaves
receive and display a given message.
Printers
Connect a serial printer to print the Historical Events Stack or a
listing of the internal application file. The time and date a message
was triggered can be included on the stack printout. You can also set
message attributes such as sending triggered messages to a printer
through the RS-232 port.
Alarms
The alarm relay activates or deactivates an external remote alarm or
warning light. Individual message attributes can be set to energize or
de-energize the alarm relay contacts on DL40 Plus or slave displays.
!
Publication 2706-6.2
ATTENTION: Use the DL40 Plus alarm relay for
annunciation purposes only. Do not use the alarm relay
for control applications.
Overview of the DL40 Plus
1–9
Background Messages
Specify a background message that will display whenever the DL40
Plus has no other triggered messages in the queue.
Hidden Messages
Hidden messages do not appear on the DL40 Plus display or have
any affect on what is being displayed. Hidden messages can be sent
to a slave display, printed, or stored on the Historical Events Stack.
Embedded Variables
Messages can contain variable data. Variable values are received
when the message is triggered. Incoming variable data can be binary,
BCD (binary coded decimal), and/or ASCII. You can also embed
time and date information in a message from the battery-backed
real-time clock of the DL40 Plus.
Data Mode Selection
When using the DL40 Plus with Remote I/O or parallel input for
communication, you can select two data modes:
• Binary
• Binary Coded Decimal (BCD) either signed or unsigned
Within any application, triggers and variable data can be in either
form. For example, message triggers can be in a binary format, while
variable data can be BCD.
Note: When using serial RS-232 or RS-485 communications, all
data is in ASCII character format.
Message Chaining
Chain messages together for display in sequence. Only the first
message in the chain is triggered from the host controller. Then each
message in the chain can trigger the next until the complete sequence
has run.
Publication 2706-6.2
1–10
Overview of the DL40 Plus
Adjustable Parameters for Serial Communications
With the DL40 Plus, you can configure RS-232 or RS-485 port
parameters as needed for compatibility with PLCs/SLCs, printers,
slave displays, or control computers.
Serial Communication Parameters
Publication 2706-6.2
Settings
Baud Rate
300, 1200, 2400, 4800, 9600, 19200
Parity
Odd, Even, No Parity
Handshake
Software, Hardware, None
Data Bits per Character
7 or 8
Null Count
0 to 255
Allows you send a string of nulls to the printer
between characters. Useful with slow printers
that drop characters because they can’t keep
up with normal DL40 Plus output.
Page With
20 –132 characters
Useful for narrow width printer devices.
Overview of the DL40 Plus
Operating Modes
1–11
The DL40 Plus has a number of operating modes. Each mode
provides tools to perform a different set of functions. The following
sections provide a brief overview of the operating modes.
Run Mode
Run mode is the normal operating mode for the DL40 Plus. In Run
mode, messages are triggered for display on the DL40 Plus and slave
message displays (if desired).
The Remote I/O version of the DL40 Plus comes up in Run mode
after a reset. The Parallel port version also comes up in Run mode,
except when the Run Mode/Debug DIP switch is set to Debug on the
DL40 Plus.
The Remote I/O version of the DL40 Plus has 4 Run modes.
• Message/Variable/Slave Mode triggers a message with variables
containing up to 20 ASCII or 40 BCD characters in any
combination as long as the total does not exceed 10 words. This
mode allows you to override the slave address attribute.
• Message/Variable Mode is similar to the Message/Variable/Slave
mode but you cannot override the slave address attribute.
• Message List Mode triggers a message list of up to 20 messages
in round robin order.
• Bit Trigger Mode triggers a priority message and up to 496
messages in priority and/or round robin order.
The Parallel port version of the DL40 Plus has 2 Run modes.
• Message/Variable/Slave Mode triggers a message with variables
containing up to 20 ASCII or 40 BCD characters in any
combination as long as the total does not exceed 10 words.
• Message List Mode triggers a message list of up to 20 messages
in round robin order.
To select Run mode, use the Onboard Editor or the Offline
Programming Software.
Publication 2706-6.2
1–12
Overview of the DL40 Plus
Serial Triggering (RS–232/RS–485)
Both the Remote I/O and the Parallel port versions of the DL40 Plus
support serial triggering. The RS-232, RS-485, or Keyboard port
can control message triggering and variable data communications.
Serial triggering uses Open protocol, which communicates using
ASCII characters in a serial data stream.
Open protocol is available in the following run modes:
• Message/variable/slave mode
• Message/variable
• Message list
Offline Modes
The DL40 Plus offers the following offline operating modes:
• Help mode
• Historical Recall mode
• Remote Program mode (for Offline Programming Software)
• RS-232/RS-485 Port Configuration mode
• Clock mode
• Print mode
• Debug mode (on Parallel port versions only)
Special Messages
Message Number
Content
Message Number
Content
901 (or 01)
Terminate Message – Clear Display
909 (or 09)
Clear Historical Events Stack
902 (or 02)
Clear Queue
910 (or 10)
Set Interactive Clock
911 (or 11)
Set Clock with Variable Data
904 (or 04)
Terminate Message – Clear Display and
Queue
Reset Unit
912 (or 12)
Send Time to PLC➀
905 (or 05)
Test Display
913 (or 13)
Send Date to PLC➀
914 (or 14)
View Display Parameters
903 (or 03)
906 (or 06)
907 (or 07)
908 (or 08)
➀
Special messages let you monitor and control certain functions of the
DL40 Plus without leaving Run Mode. Special messages normally
occupy message numbers 901 through 916. You can move special
messages to message numbers 1 to 16, or disable them with the
Offline Programming Software or Onboard Editor.
Print Historical Events Stack –
Chronological Order
Print Historical Events Stack – Frequency
of Occurrence
View Historical Events Stack
Remote I/O versions only
Publication 2706-6.2
915 (or 15)
916 (or 16)
Stop Special Messages/Resume Run
Mode
Set Display Intensity
Overview of the DL40 Plus
Controller Support
for Remote I/O
1–13
The following PLCs and SLCs support Remote I/O communications
with the DL40 Plus.
• PLC-5/11, 5/15➀, 5/20, 5/25, 5/30, 5/40, 5/60, 5/80, 5/250
• PLC-2, PLC-5/10, 5/12 with Catalog Number 1771-SN Scanner
• SLC-5/02, 5/03, 5/04 with Catalog Number 1747-SN Scanner➁
➀
If you are using a PLC-5/15 with partial rack addressing and block transfers, you must use Series
B, Rev. J or later.
➁
Block Transfer requires a Series B or later Scanner.
PassThrough Support over a DH+ Link
PLC-5 Remote I/O PassThrough lets you upload and download
message files between a computer and a DL40 Plus connected by
Remote I/O to a PLC on the DH+ link. Refer to Appendix D for an
example application. Separate wiring from the computer to the
DL40 Plus is not required. For a list of supported controllers, see
table below. Refer to Appendix D for additional instructions.
Computer
DH+ Network
Remote I/O Link
Remote I/O Link
DL40 Plus
DL40 Plus
PLCs supporting PassThrough over a DH+ link
PLC Types
Series
Revision
PLC-5/11
All
PLC-5/15
DL40 Plus
Computer interface boards for PassThrough
Catalog No.
Description
All
1784-KT
1/ -slot interface board
2
B
N or later
1784-KTX
1/ -slot interface board
2
PLC 5/20
All
All
1784-KL
Interface board for Allen-Bradley
1784-T45 or -T47
PLC 5/25
A
J or later
1784-KT2
Interface module for IBM PS2
PLC 5/30
A
B or later
1770-KF2
Serial to DH+ interface module
PLC 5/40
A
B
E or later
1784-PCMK
PCMCIA interface board
PLC 5/60
A
B
B or later
PLC 5/80
All
All
PLC 5/250
All
All
Publication 2706-6.2
1–14
Overview of the DL40 Plus
PassThrough Support over an Ethernet Link
PLC-5E Remote I/O PassThrough lets you upload and download
message files between a computer and a DL40 Plus connected by
Remote I/O to a PLC on the Ethernet link. Refer to Appendix E for
an application example. Separate wiring from the computer to the
DL40 Plus is not required. For a list of supported controllers, see
table below.
Computer
Ethernet Network
Remote I/O Link
Remote I/O Link
DL40 Plus
DL40 Plus
DL40 Plus
The following table lists the Allen-Bradley PLCs that support
PassThrough file transfers with the DL40 Plus message display over
an Ethernet link as of this printing.
PLC Types
Series
Revision
PLC 5/40E
A
B
E or later
PLC 5/60E
A
B
B or later
PLC 5/80E
All
All
PLC 5/250
All
All
Use one of the Allen-Bradley Ethernet computer interface boards (or
its equivalent) for PassThrough file transfers.
• Catalog Number 6628-A5: Ethernet adapter module for IBM PC
compatible computers
• Catalog Number 6628-A7: Ethernet adapter module for IBM
MicroChannel bus compatible computers
Publication 2706-6.2
Overview of the DL40 Plus
Available Catalog Numbers
1–15
DL40 Plus displays are available with 128K bytes of memory in
either 2- or 4-line versions with two communication options.
2706–LV2R
Display Type:
2 – Two–line
4 – Four–line
Communication Options:
R – RIO
P – Parallel Port
S – Slave
The table below shows the standard catalog numbers for the DL40
Plus and how they equate to previous versions of the DL40 displays.
DL40 Plus
Catalog Number
2706–LV2P
2706–LV4P
Description
Two–line display, AC supply
with parallel port
Four–line display, AC supply
with parallel port
Equivalent Catalog Numbers for
Previous Versions of the DL40
2706–E23J16, 2706–E23C16
2706–E23J32, 2706–E23C32
2706–E43J32, 2706–E43C32
2706–E43J64, 2706–E43C64
2706–E43J128, 2706–E43C128
2706–LV2R
Two–line display, AC supply
with remote I/O
2706–E23J16B1, E23C16B1
2706–E23J32B1, 2706–E23C32B1
2706–LV4R
Four–line display, AC supply
with remote I/O
2706–E43J32B1, 2706–E43C32B1
2706–E43J64B1, 2706–E43C64B1
2706–E43J128B1, 2706–E43C128B1
Publication 2706-6.2
Installing the Software
Chapter Objectives
This chapter describes how to install the DL40 Offline Programming
Software on your computer. It also explains the basic steps required
to configure your system for use with PassThrough on systems
equipped with an Allen-Bradley PLC capable of Remote I/O
PassThrough file transfers.
Section
Personal Computer
Requirements
Page
Personal Computer Requirements
2–1
Package Contents
2–1
Installed Files
2–2
Memory Requirements
2–2
Memory Management
2–3
Installation
2–3
Basic Installation (without PassThrough file transfers)
2–4
Installing Software for DH+ PLC PassThrough
2–5
Installing Software for Ethernet PLC PassThrough
2–11
Starting the Program
2–13
Establishing Initial Non–network Communications
2–13
The minimum equipment required to install and run the Offline
Programming Software consists of an IBM compatible personal
computer (PC) with:
•
•
•
•
•
•
a 386 (or higher) processor
640K RAM
one 31/2 inch micro diskette drive
a hard disk with at least 1 Megabyte of available space
one open serial port (COM1 or COM2)
one open printer port (LPT1, LPT2, LPT3, LPT4, COM1, or
COM2) for printing messages
• a printer
Package Contents
In addition to this manual, the Offline Programming Software
package consists of three disks and a number of documents.
They include:
• DL40 Plus Offline Programmer
• DL40 Plus PASSTHROUGH Drivers
• DL40 Plus INTERCHANGE Software
Publication 2706-6.2
2–2
Installing the Software
Installed Files
After installing the software, your computer will contain a
DL40.EXE as well as a PS.HLP file containing online help. If you
install the PassThrough capability, you will also have the
PassThrough files and their companion TSR (Terminate and Stay
Resident) server files.
Memory Requirements
Important: For the Offline Programming Software to operate
without generating warning messages about memory limitations,
your computer needs a minimum available memory of 570K RAM.
Editing a 128K message file requires the full 570K. Smaller
message files require less computer memory.
With DOS versions prior to 5.0, use the CHKDSK↵ command at
the DOS prompt to determine the available conventional RAM on
your system. The available conventional RAM will be reported in
bytes. Your system must have 583,680 or more free bytes RAM to
run the Offline Programming Software and edit large application
files.
With DOS versions 5.0 or higher, use CHKDSK ↵ or the MEM↵
command to accomplish the same task. (The MEM ↵ commands
reports more quickly and in greater detail than does CHKDSK ↵ .)
The value reported for free conventional memory must be at least
570K.
The following table provides RAM recommendations for creating
and editing message files and requirements for using PassThrough.
If your computer has less than the required bytes free, reduce the
number of memory resident programs (communications programs,
mouse drivers, etc.) your computer is running. For additional
information on increasing the amount of available memory, refer to
the configuration section of your computer’s DOS manual.
PC memory requirements for typical activities
Create and edit message files
DL40 Plus, 128Kbyte
message memory
CHKDSK
bytes free
580,000 bytes
(recommended)
PLC–5 PassThrough w/DH+
PLC–5 with a DH+
Communications Interface Card
515,000 bytes
(required)
PLC–5 with an Ethernet
Communications Interface Card &
FTP’s PC/TCP Software
515,000 bytes
(required)
Function
PLC–5 PassThrough w/Ethernet
Publication 2706-6.2
For a
Installing the Software
Memory Management
2–3
Your computer system configuration at startup can affect the amount
of RAM available for use by the Offline Programming Software.
DOS offers a number of options that can help increase the amount of
RAM available to programs.
With DOS versions 5.0 or earlier you can maximize available RAM
by editing your CONFIG.SYS file. Your CONFIG.SYS should
contain text lines similar the following:
DOS=HIGH, UMB
DEVICE=C:\DOS\HIMEM.SYS
BUFFERS=10
FILES=10
STACKS=9,128
In the example above, the BUFFERS, FILES, and STACKS values
are set to low values to conserve RAM for program operation.
Important: The line DOS=HIGH,UMB should be used only with
DOS versions 5.0 or higher.
DOS version 6.0 introduced the MEMMAKER command, which
automates memory management and can often free large amounts of
RAM. DOS 6.0 and higher versions also allow you to create multiple
configuration files from which to choose at startup. This feature can
prove useful on PCs used for programming the DL40 as well as other
activities.
Refer to your DOS user manuals for information on creating and
editing CONFIG.SYS files, techniques for optimizing memory, and
using multiple configuration files on a single PC.
Installation
The Offline Programming Software can be installed and run in any
of three distinct environments:
• without PassThrough file transfers
• with PassThrough file transfers over a DH+ link
• with PassThrough file transfers over an Ethernet link
Installation of the basic Offline Programming Software is the same
for all three environments. You will have to perform additional steps
to install PassThrough capability on either a DH+ or Ethernet link.
Publication 2706-6.2
2–4
Installing the Software
Basic Installation
(without PassThrough)
Use the following procedure to install the basic Offline Programming
Software files on an IBM PC. Note that prompts appearing here
represent a typical PC. The prompts you see on your computer may
vary slightly from those shown here.
Note: Do not automatically install all of the program disks. First
determine the type of installation you require and install just the
programs required.
1. If running in a Windows environment, restart your computer in
DOS mode. Windows NT users need to restart their computers
with a Windows 95 or less operating system.
2. Start your computer and log on to the hard disk (normally you
will see the DOS prompt C:>).
Note: Depending on your installation, your DOS prompt may be
different.
3. Insert the DL40 Offline Programmer disk into the micro drive.
Most often this will be the A: drive.
4. At the DOS prompt (C:>), type:
A:INSTALL↵
5. Follow the onscreen installation prompts until installation is
complete and the C:> prompt reappears. Note: If the Offline
Programming Software program is already on disk, you will be
able to overwrite the program during installation.
6. The installation procedure automatically creates a default
sub–directory which contains the Offline Programming Software
program. By default that directory is DL40. Change to that
directory by typing:
CD\DL40↵
Publication 2706-6.2
Installing the Software
Software Installation
for DH+ PLC PassThrough
2–5
If you are using a DH+ link and want to enable PLC PassThrough
file transfers, you must perform the following additional steps after
completing the basic installation described above.
The following paragraphs outline only the most essential information
required to install and use PassThrough file transfers on a DH+ link.
Refer to the instructions that came with your DH+ add-in board.
Install and Configure Your DH+ Communication Interface Card
Install and configure your DH+ communication interface card. Refer
to the instructions that came with the card for information on how to
install and configure it. Currently the following DH+ cards are
supported by the Offline Programming Software:
– 1784-PCMK
– 1770-KF2
– 1784-KT2
–
–
–
1784-KL
1784-KT
1784-KTX
Important: Be sure to record the IRQ and Card address for each
interface card. You will need to know them later in the
configuration process.
Install the Offline Programming Software
Perform the basic installation procedure described earlier in this
chapter to install the Offline Programming Software on your
personal computer.
Publication 2706-6.2
2–6
Installing the Software
Install and Configure INTERCHANGE
Your Offline Programming Software package contains a runtime
version of Allen-Bradley’s INTERCHANGE software and a number
of other files. You must install this package to perform
PassThroughs over a DH+ network device.
INTERCHANGE software is an Application-Programming Interface
(API) that provides a host computer running the MS-DOS operating
system with a library of executable commands. INTERCHANGE
software lets multiple applications share a single common interface
module to communicate with various devices on DH+ and/or
DH-485 networks. Use the following procedure for installation:
1. Insert the INTERCHANGE disk into your 31/2 inch drive.
2. Start the automated installation procedure by typing:
A:INSTALL↵
This program copies all required INTERCHANGE files to the
directory \ABIC\BIN on your hard disk. Those files include the
executable INTERCHANGE servers listed below:
– DTL_KT.EXE
– DTL_DF1.EXE
– CFG_KT.EXE
–
CFG_DF1.EXE
–
RNASTR.EXE
–
RNA.EXE
Important The next part of the installation and configuration
process depends on how you use your PC. If you use your PC for
other activities in addition to offline programming, then you
should create a new batch file as described in step 3. If you use
your computer solely for the Offline Programming Software, then
modify your AUTOEXEC.BAT file as described in step 4 below.
3. If you use your PC for other activities in addition to offline
programming, then create a new batch file containing the
INTERCHANGE server files listed above. You can name the file
anything you want, but it must end with the extension .BAT.
Assume you call the file ABICRUN.BAT, and your hard drive is
drive C:
a. Create the file with any ASCII text editor. If you use the DOS
text editor, type:
EDIT C:\ABICRUN.BAT↵
b. Type in the names of the INTERCHANGE server files.
Put each file name on its own line followed by a hard return:
DTL_KT.EXE
DTL_DF1.EXE
CFG_KT.EXE
CFG_DF1.EXE
RNASTR.EXE
RNA.EXE
Publication 2706-6.2
Installing the Software
2–7
c. Save the file. If you are using the DOS text editor, type:
[ALT]FXY
d. Skip step 4 and go on to step 5.
4. If you use your PC solely for the Offline Programming Software,
you need not create a new batch file. Instead, you should modify
your AUTOEXEC.BAT file to load the INTERCHANGE server
files whenever you start your system.
a. Open the AUTOEXEC.BAT file with any ASCII text editor. If
you use the DOS text editor, type:
EDIT C:\AUTOEXEC.BAT↵
Your AUTOEXEC.BAT file contents will appear in the editing
window.
b. Move the cursor to the end of the file.
c. Type in the names of the INTERCHANGE server files. Put
each file name on its own line followed by a hard return:
DTL_KT.EXE
DTL_DF1.EXE
CFG_KT.EXE
CFG_DF1.EXE
RNASTR.EXE
RNA.EXE
Do not close the file at this time.
5. If your AUTOEXEC.BAT is not open in your ASCII text editor,
then open it now. If you use the DOS text editor, type:
EDIT C:\AUTOEXEC.BAT↵
Your AUTOEXEC.BAT file contents will appear in the editing
window.
6. Locate the line in your AUTOEXEC.BAT file that begins with
the word PATH. This is your system’s “Path Statement”, which
tells DOS where to look for executable files when no specific
path is otherwise specified.
7. Move to the end of the Path line and insert the complete name for
the directory in which the INTERCHANGE server files were
stored. In a standard installation they are located in
C:\ABIC\BIN. When you have finished editing it, your Path
Statement will look like this:
PATH=C:\DOS;C:\APP1;C\APP2;C:\ABIC\BIN
Publication 2706-6.2
2–8
Installing the Software
Create CFG_KT.INI File
INTERCHANGE needs to know exactly what hardware you are
using, and how it is configured. This information is provided by a
configuration file (CFG_KT.INI) modified to match your own
installation.
1. Edit the file with any ASCII text editor. If you use the DOS text
editor, type:
EDIT C:\ABIC\BIN\CFG_KT.INI↵
The CFG.INI file that installs with INTERCHANGE includes
configurations for numerous cards. Lines preceded by a
semicolon (;) have been commented out. To activate your
interface card, edit and uncomment the appropriate options by
removing the semicolon at the beginning of the line.
If you are using a card other than the 1770-KF2 go to step 2
below. If you are using the 1770-KF2 communications interface
card, skip step 2 and go directly to step 3.
2. If you are using a card other than the 1770-KF2, the contents of
the CFG_KT.INI file should be similar to the format shown in the
sample file below. This sample is for a 1784-KT board:
[DTL_KT.Options]
PATH=C:\ABIC\BIN
[DTL_KT.1]
DEVICE=KT
MEMORY=C800
PROTOCOL=DHPLUS
IRQ=5
STATION=77
NAME=DTL_KT 1
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
In this file:
① This line identifies the file and prefaces a section of the file used to record
information common to all the communications interface cards on your system.
② PATH line that designates the directory where the INTERCHANGE server
programs are located. This will be the same value for all interface cards on your
system.
③ Blank line to separate sections and improve readability.
④ This line identifies the general class of hardware device (in this case a KT
device) and a logical pushwheel identifier of 1. Note: The DL40 Offline
Programming Software assumes that pushwheel 1 is used. Only use pushwheel
1 when communicating with the DL40 Offline Programming Software.
⑤ DEVICE line that specifies the exact communication interface card used.
Acceptable values include KT, KTX, KL, KT2, or PCMK.
⑥ MEMORY line that matches the dip switch settings on the interface card.
⑦ PROTOCOL line that identifies the protocol in use.
⑧ IRQ line that matches the dip switch settings on the interface card.
⑨ STATION line designates the octal station address on the communications link.
⑩ NAME is a unique string you define to specify to this configuration.
Publication 2706-6.2
Installing the Software
2–9
Models for other interface cards appear below. Note that some of
the values in these files vary depending on the installation.
1784-KT2
[DTL_KT.Options]
PATH=C:\ABIC\BIN
[DTL_KT.1]
DEVICE=KT2
MEMORY=C400
PROTOCOL=DHPLUS
IRQ=5
STATION=77
NAME=DTL_KT2
1784-KL
[DTL_KT.Options]
PATH=C:\ABIC\BIN
[DTL_KT.1]
DEVICE=KL
MEMORY=E000
PROTOCOL=DHPLUS
IRQ=2
STATION=77
NAME=DTL_KL 1
1784-KTX
[DTL_KT.Options]
PATH=C:\ABIC\BIN
[DTL_KT.1]
DEVICE=KTX
MEMORY=D400
PROTOCOL=DHPLUS
IRQ=10
STATION=77
NAME=DTL_KTX1
1784-PCMK
[DTL_KT.Options]
PATH=C:\ABIC\BIN
[DTL_KT.1]
DEVICE=PCMK
MEMORY=CF00
PROTOCOL=DHPLUS
IRQ=7
STATION=77
NAME=DTL_PCMK
Publication 2706-6.2
2–10
Installing the Software
3. If you are using the 1770-KF2 communications interface card, the
contents of the CFG_KT.INI file should be similar to the format:
[DTL_KT.Options]
PATH=C:\ABIC\BIN
[DTL_DF1.1]
DEVICE=DF1
BAUD=9600
IRQ=4
COM_PORT=2
NAME=DTL_DF1
ERROR=1 ①
PARITY=0 ②
DUPLEX=1 ③
① 0=BCC,1=CRC
② 0=No Parity, 1=Even Parity
③ 0=Half Duplex, 1=Full Duplex
4. Save the file. If you are using the DOS text editor, type:
[ALT]FXY
Publication 2706-6.2
Installing the Software
Installing the Software for
Ethernet PLC PassThrough
2–11
If you are using an Ethernet link and want to enable PLC
PassThrough file transfers, you must first modify your
CONFIG.SYS and AUTOEXEC.BAT files, and install and configure
the following products on your computer:
• Allen-Bradley Ethernet communications interface card (Cat. Nos.
6628-A5 or -A7) or equivalent
• FTP’s PC/TCP Software for DOS/Windows (FTP Cat. No.
PC-210)
Install Ethernet Card
Follow the instructions that came with your Allen-Bradley Ethernet
communications interface card to install and configure it on your
personal computer.
Install the PC/TCP Software
Follow the instructions that came with FTP’s PC/TCP Software to
install it on your personal computer.
Install the Offline Programming Software
Perform the basic installation procedure described earlier in this
chapter to install the Offline Programming Software on your
personal computer.
Modify CONFIG.SYS & AUTOEXEC.BAT Files
The following steps show a sample network setup. Consult with
your network administrator to determine if this setup applies in your
environment.
1. Change to the directory containing the PC/TCP drivers. Type:
CD \PCTCP↵
2. At the C:\PCTCP> prompt, type:
RENAME FTP22DOS.INI PROTOCOL.INI
3. Open the CONFIG.SYS file with any ASCII text editor. If you
use the DOS text editor, type:
EDIT C:\CONFIG.SYS↵
Your CONFIG.SYS file contents will appear in the editing
window.
4. Move the cursor to the end of the file.
Publication 2706-6.2
2–12
Installing the Software
5. Assuming you have installed the Ethernet Board drivers in the
directory C:\PCTCP (the default), be sure the following lines
appear in your CONFIG.SYS file.
DEVICE=C:\PCTCP\PROTMAN.DOS /I:C:\PCTCP
DEVICE=C:\PCTCP\SMC8000.DOS
DEVICE=C:\PCTCP\DIS_PKT.GUP
6. Save the file. If you are using the DOS text editor, type:
[ALT]FXY
7. Open the AUTOEXEC.BAT file with any ASCII text editor. If
you use the DOS text editor, type:
EDIT C:\AUTOEXEC.BAT↵
Your AUTOEXEC.BAT file contents appears in the editing
window.
8. Move the cursor to the end of the file.
9. The following lines should appear in the AUTOEXEC.BAT file.
If they are not there, add them now.
SET PCTCP=C:\PCTCP\PCTCP.INI
C:\PCTCP\NETBIND.COM
C:\PCTCP\ETHDRV.EXE
For additional information regarding installation of your PC/TCP
software, refer to the section on installing an NDIS driver in the
PC/TCP Software Installation Guide.
Restart Your PC
When installation is complete, remove the installation diskette from
the 31/2 inch micro drive and store all installation software in a safe
place. Finally, restart your PC to activate your changes to the
CONFIG.SYS and AUTOEXEC.BAT files.
Configure Your PLC
Use Allen-Bradley’s 6200 Series PLC-5 programming software or
the EIBOOT utility to set the PLC’s IP address. Refer to the
documentation that came with your PLC for additional configuration
information.
Publication 2706-6.2
Installing the Software
Starting the Program
2–13
If you have installed the Offline Programming Software without
PassThrough processing, your computer will return to the DOS
prompt, C:\DL40>. If you have installed PassThrough processing,
your computer returns to the directory it displayed when you began
the PassThrough processing installation.
If you do not return to the C:\DL40> directory, change directories by
typing:
CD C:\DL40↵
You may then start the the Offline Programming Software program
by typing:
DL40↵
Establishing Initial
Non–networked
Communications
The communication port settings on your computer and the DL40
must be the same in order to communicate.
• the port usage on the RS-485 port must be set to PRGMR to
perform message file transfers via the RS-485 port.
• the DL40 RS-232 port will always communicate with the DL40
Offline Programming Software regardless of the port
configuration.
• set your computer’s serial communication port to the following:
–
–
–
–
baud rate 9600
data bits 8
parity none
handshaking none
• Use the [SELECT] and [ENTER] push buttons on the front panel
of the DL40 to select SET RS232PORT?– PGMR/PRNTER
SETUP or SET RS-485 PORT?–PRGMR and set the parameters
to match the setting of your computer’s serial communication
port.
Note: Select Enable DIP switch (SW2-9) must be ON.
• You can also change the settings of the DL40’s serial ports with
the [CTRL][R] command using the DL40’s Onboard Editor and
an IBM compatible keyboard connected to the rear keyboard port
of the DL40 display.
Publication 2706-6.2
Navigating the Software
Chapter Objectives
This chapter provides a basic understanding of how to move around
in the DL40 Offline Programming Software. The information in this
chapter will help you:
• start the program
• move around within the program
• exit the program
This chapter contains the following topics:
Topic
Starting the Software
Page
Starting the Software
3–1
Title Screen and Main Menu
3–2
Getting Help
3–3
Setup Menu
3–4
Menu Control Keys
3–6
Shortcut Keys
3–6
Exiting the Software
3–7
After you have installed and set up the Offline Programming
Software on your computer, you can run the program at any time.
The most basic way to do so is to:
1. Start your computer.
2. Make sure you are logged on to the C: drive by typing:
C:↵
3. Go to the directory C:\DL40 by typing:
CD C:\DL40↵
4. Start the program by typing:
DL40↵
Publication 2706-6.2
3–2
Navigating the Software
Title Screen & Main Menu Bar
The program opens with the Title screen shown below. The screen
identifies the product, and indicates the revision number and date of
the software. Close this screen and open the Main Menu screen by
pressing any key.
Opening title screen
Main Menu screen
Menu Bar
Cursor
Menu Title
Menu Item
Date & Time
Publication 2706-6.2
Navigating the Software
Getting Help
3–3
The Offline Programming Software offers context-sensitive online
Help at any time. To use Help:
• press [F1] to access a Help screen offering information about the
highlighted menu item.
• press [F1] again to replace the current Help screen with the Menu
Key Control Help screen.
• press [ESC] to close the Menu Key Control Help screen and
return to the context-sensitive Help screen
• press [ESC] to close the context-sensitive Help screen and return
to the Main screen
Sample Help Screen
Use the [ ] and [ ] keys
to scroll through the help text.
Publication 2706-6.2
3–4
Navigating the Software
Setup Menu
Use the Setup menu to match the software to your color or
monochrome monitor, and to set the date and time. Access the Setup
menu by using the right and left arrow keys to move to Setup and
pressing [↵], or by pressing [S] at the Main menu.
Setup Menu
Configuring the Program to Match Your Monitor
The Offline Programming Software supports both color and
monochrome displays. To change the display type, move the cursor
to Setup on the Main menu and press [↵ ]. Select Colors, and then
select either Color or Monochrome. Select Yes to confirm your
choice, then press [↵]. A message appears in the center of the screen
to indicate that the software is saving your selection to its setup file.
Press [Q] or [ESC] repeatedly to return to the Main menu.
Setup→Colors Screen
Publication 2706-6.2
Navigating the Software
3–5
Setting Time & Date
You can set the time and date by selecting Setup→Time & Date or by
pressing [S][T] from the the Main menu bar. The Date & Time
window appear showing the current date and time setting of the
personal computer. The cursor will highlight Time when the window
first opens. Press [↵] and input the desired time using military style
(24-hour) format. Press [↵] to record your changes and move the
cursor to Date. Press [↵] and input the desired date. Press [↵] to
record your changes and move the cursor to Quit.
Setup→Time & Date Screen
Publication 2706-6.2
3–6
Navigating the Software
Menu Control Keys
Use the following keys to navigate through the Offline Programming
Software menus. These keys have the same effect wherever they are
used in the software. Individual screens may use additional
keystroke commands. These additional commands are described
immediately below the sample screens that appear throughout this
manual.
Help. Pressing F1 when Help is open will open the Menu Key
Control help screen
Toggle Help screen between partial and full screen view.
Return to the previous menu.
↵
Select highlighted menu item.
↑
Highlight previous menu item.
↓
Highlight next menu item
→
Move the cursor to the right
←
Move the cursor to the left
Highlight first menu item.
Highlight last menu item.
Shortcut Keys
Publication 2706-6.2
You can also select most menu items by typing their initial letter.
For example, to exit the program you can type [E][Y]. [E] is the
initial letter in the Exit Main menu item, and [Y] is the initial letter
of the Yes Exit menu item.
Navigating the Software
Exiting the Software
3–7
You can exit the Offline Programming Software at any time by
repeatedly pressing [ESC] until the Exit Confirmation menu appears.
Press [↵] to confirm your intention to exit the program.
Exiting the Offline Programming Software
You can also exit the program by typing the shortcut keys [E][Y]
from the Main menu.
Publication 2706-6.2
Creating Message Files
This chapter describes the functions available to you from the
Develop menu. As its name implies, the options available from this
menu provide the tools needed to create and manage your application
files for the DL40 message display. This chapter contains the
following topics:
Page
Develop Menu
4–2
File Selection Screen
4–4
Create New File Window
4–5
Data Path Directory Window
4–6
Develop Screen
4–7
Messages Menu
4–8
Edit Message Screen
4–9
Message Text Window
4–10
Create New Message Screen
4–16
Copy Messages Screen
4–17
Delete Message Screen
4–19
Renumber Messages Screen
4–20
Text Search Screen
4–22
Modify Message Attributes Screen
4–24
Message Attribute Default Screen
4–32
Options Menu
4–34
Ports Menu
4–36
Verify Menu
4–39
Device Menu
4–44
Publication 2706-6.2
4–2
Creating Message Files
Develop Menu
To open the Develop menu, use the right and left arrow keys to
highlight Develop on the Main menu bar, then press [↵ ].
Develop Menu
Special keys
You may use the following special keys on the Develop menu.
↓
↑
Move the cursor to the desired function
Move the cursor directly to the first menu item (Select)
Move the cursor directly to the last menu item (Quit)
↵
Selects the item highlighted by the cursor
Closes the Develop menu and returns cursor to Main menu
Get Online Help
Publication 2706-6.2
Creating Message Files
4–3
Notes
From the Develop menu you can choose from the following:
• Select File to modify an existing data file.
• Create New File to create a new data file.
• Directory to specify a data path
The Offline Programming Software supports both color and
monochrome monitors. Make sure your monitor type matches the
type selected in the Setup menu. Refer to Chapter 3 for instructions
on changing your monitor type.
You cannot Select a file unless that file is located on the current DOS
path. If necessary, use the Directory menu item to change
directories. The window that opens when you pick DevelopSelect
File shows the current directory in the upper left.
Publication 2706-6.2
4–4
Creating Message Files
File Selections Screen
When Select File is selected, a window appears with the default path
in the upper left corner and a list of the files found in that path.
If you want to edit files under a different path, press [ESC], highlight
Directory, and press [↵ ]. You can then edit the program’s data path
in the window show below.
File Selections screen showing typical application file list
Path
Time file was created
or last edited
Date file was created
or last edited
File length in bytes
Special Keys
Use the following special keys on the File Selections screen.
↓
↑
Move the cursor to the desired file
Move the cursor directly to the first file
Move the cursor directly to the last file
↵
Selects the item highlighted by the cursor (Opens Develop Screen)
Returns to the top level of the Develop menu
Get Online Help
Notes
Use the arrow keys to move to the file you want to edit and press
[↵ ]. If the name of the file you want to edit does not appear here,
you may be using the wrong data path. Change the data path by
backing up and selecting Directory on the Develop menu.
Publication 2706-6.2
Creating Message Files
Create New File Window
4–5
When Create New File is selected on the Develop menu, a window
opens in which you can enter a new file name. Type in the file name
and press [↵ ]. You can type a drive and directory path as well if you
do not want to store the file on the current data path.
Create New File Window
If the default path is to be used, enter only the file
name. If a path other than the default path is to be
used, enter the path in the form: Drive:\Directory\File.
Flashing cursor
Special keys
You may use the following special keys on this window.
←
→
Moves the cursor forward or backward through the file name to
allow editing
↵
Accepts the file name (and path, if applicable).
Opens Develop Screen
Returns to the top level of the Develop menu
Get Online Help
Notes
When creating a new file you will be asked to specify a path and
filename in the format:
Drive:\Directory\File
If you do not specify a path, then the currently active path will be
used.
When you press [↵ ] to accept the file name in the Create a New File
window, the Device menu opens.
Publication 2706-6.2
4–6
Creating Message Files
Data Path Directory Window
Change data path directories by selecting Develop→Directory from
the Main menu bar. When you enter a complete directory path in the
Directory window the Offline Programming Software will use that
path as a default for all file activities. Override the Directory setting
by typing another complete data path when naming files.
Data Path Directory window
Special Keys
Use the following special keys on this window.
←
→
Moves the cursor forward or backward through the data path
description to allow editing
↵
Accepts the data path directory you have entered in the window
Returns to the top level of the Develop menu
Get Online Help
Notes
When creating a new data path, specify the path in the format:
Drive:\Directory1\Directory2\Directory3
You can change the selected data path directory at any time the
Message menu is displayed. The change becomes effective
immediately.
Publication 2706-6.2
Creating Message Files
Develop Screen Menu
4–7
Editing an existing file and creating a new file use the same screen.
After entering the name and data path of a file to create or change,
the screen shown below appears. Notice that the Main Menu bar has
been replaced by a the Develop Menu bar. Use this menu bar as you
would use the Main menu bar.
Develop Screen menu after selecting or creating a file
Remaining (free) memory
Special Keys
Use the following special keys on this menu.
←
→
Moves the cursor to the desired function
Moves the cursor directly to the desired
function: Messages, Options, Ports,
Verify, or Exit.
Moves cursor directly to the first function
(Messages)
Moves cursor directly to the last function
(Exit)
or
↵
Selects the function highlighted by the cursor
Get Online Help
Notes
The Messages, Options, Ports, Verify, and Device branch menus
control every aspect of your message file. Work through each of
these menus in turn to avoid omissions and mistakes.
Specify a selection for every item on the Develop menu bar branch
menus. If you have not edited every selection, a System Attribute
Warning message appears when you save the file.
Publication 2706-6.2
4–8
Creating Message Files
Messages Menu
Use the selections on the Messages menu to create, edit, and control
the display format of messages intended for display on the DL40.
Messages menu
Special keys
Use the following special keys on this menu.
↓
↑
Moves the cursor to the desired function
Moves the cursor directly to the first menu item
Moves the cursor directly to the last menu item (Quit)
↵
Selects the item highlighted by the cursor
Closes the Develop menu and returns cursor to Main menu
Get Online Help
Publication 2706-6.2
Creating Message Files
Edit Message Screen
4–9
After you have selected Edit Message, the Message Selections
window shown below opens. Select the message you want to edit,
then press [↵ ] to open the Message Text window
Message Selections after selecting Edit Message
Special keys
You may use the following special keys on this window.
↑
↓
Moves the cursor to the desired message.
Moves cursor directly to the first message.
Moves cursor directly to the last message.
↵
Selects the message highlighted by the cursor and
opens the Message text window.
Closes the window and returns to the Messages menu.
Get Online Help.
Publication 2706-6.2
4–10
Creating Message Files
Message Text Window
After you have selected a message from the Message Selections
window by highlighting it and pressing [↵ ], a window opens
showing the text of the selected message. In this window you can
edit the message as required.
Note that the Message Text window also appears when you select
Create New Message from the Messages menu as described on
page 4–8.
Message Text window
Message Text
Messages can contain up to
20 characters (including
spaces) per line.
Insert or Overstrike Mode
Column cursor is currently in
Row cursor is currently in. Note that the cursor row
does not necessarily correspond to the display line on
the DL40 if Line Usage is other than All Lines.
Publication 2706-6.2
Creating Message Files
4–11
Special Keys and Editing Rules
You may use the following keys to move through and edit your
message text.
←
↑
Moves the cursor up or down one line at a time
→
Moves the cursor right or left without changing the underlying text
or
Moves cursor directly to the beginning or end of the message
or
Moves cursor exactly 1 display window forward or backward through the
message (except when Scroll attribute is set as described on page 4–26
Toggles between insert and overstrike. If there is a character at the position
of the cursor, then the insert mode inserts a character immediately to the
left of the cursor. In overstrike mode the character at the cursor position is
replaced by any new character you type.
Deletes the character to the left of the cursor
Deletes the character at the cursor position
↵
ALT
Any alphabetic or numeric key
plus
V
F
W
X
T
or
Inserts a return to start a new line
Press the [ALT] key while entering a number from the numeric keypad
inserts an ASCII or Extended ASCII character. See Appendix A.
Inserts that character at the position of the cursor.
Y
Add or modify variables (see below)
A
Lets you set Message Attributes for only the message being created or
edited.
B
Start and end marker for blinking characters. Must be used in pairs.
The text between the markers will blink on the message display.
E
Erases message text, but leaves message number intact.
You will be asked to confirm this action before it takes effect.
N
Centers or un-centers the active message in the Edit Message window.
Returns to Messages menu. Note that the Abort Message Edit confirmation
window appears if you have changed the message in any way.
The window asks if you want to discard your changes.
Get Online Help
Toggles size of Message Text window between 40 and 200 characters
F10
Saves changes and returns to the Messages menu
Publication 2706-6.2
4–12
Creating Message Files
More About Variables
You can send variables to the DL40 from a PLC or via the Parallel
Input Port. Variables can be sent to message only in the
Message/Variable/Slave or Message/Variable Run Modes. Insert
variables using the [CTRL] key in combination with a letter.
Commands to add or modify variables include:
Command
Function
[CTRL][V]
Insert a BCD or binary variable
[CTRL][F]
Change the formatting parameters of a variable
[CTRL]W]
Insert ASCII or BCD variable data
[CTRL][X]
Insert request for ASCII input data
[CTRL][T]
Insert the system time into a message
[CTRL][Y]
Insert the system date into a message
The number of variables you can insert in any one message depends
upon your hardware and the selected Run Mode.
Insert Formatted Variable With [CTRL][V]
Use [CTRL][V] to insert a BCD or binary variable into a message.
Specify the variable type.
When you press [CTRL][V], the software will ask you to enter 3
parameters:
Parameter
Acceptable values
Variable Size
1 to 7 (including decimal point)
Decimal Point Position
(number of placed after the
decimal point)
0 to 6 (the maximum value is one less
than the variable size selected above)
Suppress Zeroes
(appearing in front of the
first significant digit)
Yes or No
The variable symbol _________ appears in the message at the
variable’s location.
The difference between a formatted variable entered with
[CTRL][V] and an unformatted variable entered with [CTRL][W] is
the flexibility to modify the parameters shown above.
Note that neither AutoRun Messages or Background Messages
support inserted variable data.
Publication 2706-6.2
Creating Message Files
4–13
Change Formatted Variable With [CTRL][F]
Use [CTRL][F] to change the formatting parameters of a variable.
Place the cursor under the symbol for the variable you want to
change, then press [CTRL][F]. The software will ask you to modify
any one or more of the 3 formatting parameters:
Parameter
Acceptable values
Variable Size
1 to 7 (including decimal point)
Decimal Point Position
(number of placed after the
decimal point)
0 to 6 (the maximum value is one less
than the variable size selected above)
Suppress Zeroes
(appearing in front of the
first significant digit)
Yes or No
Insert ASCII or BCD Variable With [CTRL][W]
Send a single word ASCII or BCD variable for insertion into a
message. Use [CTRL][W] to specify the insertion position.
The software will prompt you to specify either ASCII or BCD.
The software inserts the symbol for an ASCII or BCD variable (↕).
Note: BCD data consists of 4 digits per word, and ASCII data
consists of 2 characters per word.
Note: Variables can be strung together to form compound variables
up to 20 ASCII or 40 BCD characters long in any combination as
long as the total does not exceed 10 words.
Publication 2706-6.2
4–14
Creating Message Files
Insert Request for ASCII Input Data With [CTRL][X]
A data request requires that ASCII Input Data, an 8-bit ASCII
character, be entered through the keyboard port into the message
being displayed.
• When returning ASCII Input Data via RS-485 Port, the message
requesting the data must be triggered via the RS-485 Port. This is
true for both Parallel Port and Remote I/O units. Data is
automatically entered when you press [↵ ].
Note: Data is returned to the triggering device without
solicitation by the device and without checking that data was
received by the device.
• With Remote I/O units, the ASCII input data will be sent via
Remote I/O Port to your PLC as part of the Return Message
Number Being Displayed (described in the DL40 Plus Dataliner
Message Display User Manual, Publication 2706-6.1). Data can
be returned to your PLC in:
– Message/Variable/Slave Run Mode
– Message/Variable Run Mode
– Message List Run Mode
User requested data is sent to the PLC as part of the I/O scan. Up
to 20 ASCII characters can be sent with Block Transfer. Up to 12
ASCII characters can be sent with Discrete, depending on rack
size.
The Enter bit will be set only after all ASCII data requested has
been put into the message. Data should not be considered valid
until the Enter bit is set.
Important: If more ASCII data is requested than can be returned to
the PLC, the excess data will be lost.
To enter a data request, place the cursor just after the point where
you want to insert the request. Use [CTRL][X] to specify the
insertion position. The software inserts the symbol for a single byte
data request (↑).
Publication 2706-6.2
Creating Message Files
4–15
Insert Time Into a Message With [CTRL][T]
To enter the time into a message, place the cursor just after the point
where you want the time inserted. Use [CTRL][T] to specify the
insertion position. The software will insert the symbol for a time
variable (HH:MM:SS).
Note: The time variable occupies 8 of the available 20 characters on
a display line.
You can use the time variable in any Run Mode.
Insert Date Into a Message With [CTRL][Y]
To enter the date into a message, place the cursor just after the point
where you want the date to appear, and then press [CTRL][Y]. The
software will insert the date symbol (DAY MON DT).
Note: The date variable occupies 10 of the available 20 characters
on a display line.
You can use one date variable in any message in any Run Mode.
Notes
We recommend setting individual message attributes such as Display
Message on What Line and Scroll Message before typing in the
words of the message. This allows you to verify the placement of
characters as you type them.
If Line Usage is other than All Lines, then the display line on the
DL40 does not necessarily correspond to the cursor row value shown
on the message editing window during editing.
Publication 2706-6.2
4–16
Creating Message Files
Create New Message
After you have pressed [↵ ] to select Create New Message from the
Messages menu, the message number field (to the right of the menu
item) opens. Enter the message number you want to assign to the
new message and press [↵ ] again. The Message Text window
(shown below) opens. You can use the Message Text window to
develop and format your message text.
Create New Message screen and Message Text window
Notes
We recommend setting individual message attributes such as Display
Message on What Line and Scroll Message before typing in the
words of the message. This allows you to verify the placement of
characters as you type them.
If Line Usage is other than All Lines, then the display line on the
DL40 does not necessarily correspond to the cursor row value shown
on the message editing window during editing.
If the message number you have assigned is already being used for
an existing message, the software will display a warning message.
You can then choose between cancelling the creation or editing the
existing message.
If adding new messages would exceed the capacity of your DL40,
the software will display a warning message and automatically
cancel the create function.
Publication 2706-6.2
Creating Message Files
Copy Messages Screen
4–17
When you select Copy from the Messages menu, the Message
Selections/Message Picks window opens. All message numbers in
the current file will appear in the Message Selections column.
After you have moved all the messages to be copied into the
Message Picks column, press [F10] and the Start/Increment window
appears. When it does, press [↵ ] to open the Starting Message
Location field. Input the new message number you want to assign to
the first message on your list. Insert a value in the Increment field if
you are copying multiple messages.
For example, suppose you want to copy message numbers 1, 2, and 3
to a starting number of 10 and an increment of 5. As a result:
Message 1 is copied as message number 10.
Message 2 is copied as message number 15.
Message 3 is copied as message number 20.
When you press [F10] to accept your Message Picks, the Copy
Message confirmation window appears. Use the arrow keys to
highlight your choice and press [↵ ].
Copy (Messages) screen showing Message Selections, Start/Increment and
Confirmation windows.
Publication 2706-6.2
4–18
Creating Message Files
Special Keys
Use the following special keys on this screen.
Moves the Message Select cursor to the Message Selections or
Message Picks column
←
→
↑
↓
Moves the Message Select cursor up or down within a column
↵
Moves the highlighted message number from one column to the
other
Get Online Help
Accept message picks
Closes the Message Selections/Message Picks window without
taking action
Notes
To copy a block of messages, move the cursor to the first message on
the block and press [CTRL][B] to mark the beginning of the block.
Then move the cursor to the last message in the block and press [↵ ].
The entire block moves to the opposite column.
If you leave the increment set to 0, the spacing between messages is
retained. For example, copying message numbers 1, 3, and 7 to
message number 10 with an increment of 0 results in new copies
with message numbers 10, 12, and 16.
If any of the assigned destination message numbers are already used
for an existing message, a warning message is displayed. You can
cancel the copy, continue and overwrite the selected existing
message, skip the message, or continue and overwrite all existing
messages.
Messages are copied with the following conditions:
• Messages selected for copying appear on the Message Picks list
in the order they were selected. They do not need to be listed in
numeric order. The message with the lowest number will always
be copied to the Start number, the message with the next lowest
number will be copied to the first Increment number, and so on.
• In any of the destination message numbers are already in use by
an existing message, a warning appears allowing you to cancel
the operation, continue the copy and overwrite the existing
message, or continue and overwrite all existing messages.
• If adding new messages exceeds the capacity of your DL40, a
warning message is displayed and the copy function cancelled.
Publication 2706-6.2
Creating Message Files
Delete Message Screen
4–19
When you select Delete from the Messages menu, the Message
Selections/Message Picks window opens. All message numbers in
the current file appear in the Message Selections column.
Press [F10] to accept your Message Picks, the Delete Message
confirmation window appears. Use the arrow keys to highlight your
choice and press [↵ ].
Delete (Message) screen with Delete Message confirmation window
Special Keys
You may use the following special keys on this screen.
←
→
Moves the Message Select cursor to the Message Selections or
Message Picks column
↑
↓
Moves the Message Select cursor up or down within a column
↵
Moves the highlighted message number from one column to the
other
Get Online Help
Accept message picks
Closes the Message Selections/Message Picks without changes
Notes
To select a block of messages, move the cursor to the first message
on the block and press [CTRL][B] to mark the beginning of the
block. Then move the cursor to the last message in the block and
press [↵ ]. The entire block will be moved to the opposite column.
Publication 2706-6.2
4–20
Creating Message Files
Renumber Messages Screen
When you select Renumber from the Messages menu, the Message
Selections/Message Picks window opens. All message numbers in
the current file appear in the Message Selections column. Move a
message from the Message Selections column to the Message Picks
column, press [↵ ].
After you have moved the messages to be renumbered into the
Message Picks column, press [F10] and the Start/Increment window
appears. When it does, press [↵ ] to open the Starting Message
Location field. Input the new message number you want to assign to
the first message on your list. Insert a value in the Increment field if
you are renumbering multiple messages.
For example, suppose you want to renumber message numbers 1, 2,
and 3 to a starting number of 10 and an increment of 5. As a result:
Message 1 becomes message number 10.
Message 2 becomes message number 15.
Message 3 becomes message number 20.
Press [F10] to accept your Message Picks, the Renumber Message
confirmation window appears. Use the arrow keys to highlight your
choice and press [↵ ].
Renumber (Messages) – Message Selections/Message Picks
Publication 2706-6.2
Creating Message Files
4–21
Use the following special keys on this screen.
← →
Moves the Message Select cursor to the Message Selections or Message
Picks column
↑
↓
Moves the Message Select cursor up or down within a column
↵
Moves the highlighted message number from one column to the other
Get Online Help
Accept message picks
Closes the Message Selections/Message Picks window without taking
action
Notes
To select a block of messages, move the cursor to the first message
on the block and press [CTRL][B] to mark the beginning of the
block. Then move the cursor to the last message in the block and
press [↵ ]. The entire block will be moved to the opposite column.
If you leave the increment set to 0, the spacing between messages
will be retained. For example, renumbering message numbers 1, 3,
and 7 to message number 10 with an increment of 0 will result in
new copies with message numbers 10, 12, and 16.
Messages will be renumbered with the following condition:
• Messages selected for renumbering appear on the Message Picks
list in the order they were selected. They do not need to be listed
in numeric order. The message with the lowest number is always
assigned the Start number, the message with the next lowest
number is assigned the first Increment number, and so on.
Publication 2706-6.2
4–22
Creating Message Files
Text Search Screen
Text Search is a message editing aid that helps you edit a string of
characters that appears in several messages. Text Search finds the
first occurrence of a string, let you edit the string, and then continues
on to the next occurrence.
Strings can consist of combinations of:
• alphabetic characters
• spaces
• numeric characters
• control characters for
•
•
•
•
•
•
•
•
•
•
ASCII input data
date
[CTRL][V]
[CTRL][X]
[CTRL][Y]
variables
time
blinking character delimiter
[CTRL][W]
[CTRL][T]
[CTRL][B]
Highlight Text Search on the Messages menu, then press [↵ ]. The
Search Text window opens. Enter the string you want to edit and
press [↵ ]. A second window, the Found in Message window opens.
Across the top of this window appears the message number of the
first message in which the string was found. Inside the window is
the message text with the search string text highlighted. You can edit
the message text or search for the next occurrence of the string.
Text Search Screen - Search Text and Found in Message windows
Publication 2706-6.2
Creating Message Files
4–23
Special Keys and Editing Rules
Use the following keys to move through and edit your message text.
↑
↓
Moves the cursor up or down one line at a time
←
→
Moves the cursor right or left without changing the underlying text
or
Moves cursor directly to the beginning or end of the message
or
Moves cursor exactly 1 display window forward or backward
through the message (except when Scroll attribute is set)
Toggles between insert and overstrike. If there is a character at the
position of the cursor, then the insert mode inserts a character
immediately to the left of the cursor. In overstrike mode the
character at the cursor position is replaced by any new character
you type.
Deletes the character to the left of the cursor
Deletes the character at the cursor position
↵
ALT
Any alphabetic or numeric key
plus
V
F
W
X
T
or
Inserts a return to start a new line
Press the [ALT] key while entering a number from the numeric
keypad to insert an ASCII or Extended ASCII character.
Inserts that character at the position of the cursor.
Y
Adds or modify variables (see page 4–12).
A
Lets you set Message Attributes for only the message being created
or edited.
B
Start and end marker for blinking characters. Must be used in pairs.
The text between the markers will blink on the message display.
E
Erases message text, but leaves message number intact. You will
be asked to confirm this action before it takes effect.
N
Centers or un-centers the active message in the Edit Message
window.
Returns to Messages menu. Note that the Abort Message Edit
confirmation window appears if you have changed the message in
any way. The window asks if you want to discard your changes.
Opens Online Help
Toggles size of Message Text window between 40 and 200
characters
F10
Saves changes and returns to the Messages menu
Publication 2706-6.2
4–24
Creating Message Files
Modify Message Attributes
Screen
Attributes define how a message appears when triggered in the Run
Mode. Message Attribute Defaults are automatically assigned to a
message when it is created. Using the Offline Programming
Software, change the Message Attribute Defaults (as described later
in this chapter), or change the attributes for individual messages after
they are created.
Use Messages→Modify Message Attributes to change the message
attributes for one or more existing messages. Current attributes can
be default message attributes or message attributes selected with
[CTRL][A].
When you select Modify Message Attributes, the Message
Selection/Message Picks window opens. All message numbers in
the current file will appear in the Message Selections column. To
move a message from the Message Selections column to the
Message Picks column, press [↵ ].
After you accept your message picks, the Message Attribute window
opens. Use the arrow keys to highlight the attribute you want to
change and press [↵ ]. You will be able to select the new attribute
value from a list, or enter a number. Press [↵ ] apply the new
attribute. An explanation of each message attribute is provided on
the next page.
When you have finished choosing attribute settings, move the cursor
to Quit and press [↵ ].
Modify Message Attribute screens
Publication 2706-6.2
Creating Message Files
4–25
Special Keys
You may use the following special keys on this screen.
←
→
Moves the Message Select cursor to the Message
Selections or Message Picks column
↑
↓
Moves the Message Select cursor up or down
within a column; in the Message Attributes window
moves cursor up or down the attribute list
↵
Moves the highlighted message number from one
column to the other; in the Message Attributes
window lists or accepts attribute choices
Moves cursor to first attribute
Moves cursor directly to Quit
Get Online Help
Accept message picks
Closes the Message Selections/Message Picks
window without taking action; exits the Message
Attribute window without taking action.
More About Attributes
The modifiable message attributes you can control from the Message
Attributes menu appear below:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Display message on what line
Scroll message
Print message
Send message to Slave number
Wait Time for message
Clear message automatically
Repeat message automatically
Chain message to another
Energize relay
Send message to the stack
Send message time to the stack
Hide message on display
Acknowledge message
Slave message color
Slave message length
Echo relay to slave
Publication 2706-6.2
4–26
Creating Message Files
Display message on what line
Controls where on the DL40 Plus display the message appears.
Options are different for 2 and 4 line versions.
With 2 line units, choose from
With 4 line units, choose from
All Lines
All Lines
Line 1 Only
Line 1 Only
Line 2 Only
Line 2 Only
Line 3 Only
Line 4 Only
Scroll message
This message attribute determines whether the message will scroll
across the DL40 Message Display. You can activate scrolling only if
the Line Usage attribute (described above) has been set to use a
single line. Select Yes to activate or No to deactivate.
Print message
If the Print message attribute is set to Yes, then the DL40 Message
Display will send any triggered message to a printer through the
DL40 RS-232 Port. The message is printed only once (even if the
Repeat Message Automatically attribute is active) unless the
message contains changed variable data. If new variable data is
received while the message is running, then the message is printed
again with the new data. Select Yes to activate or No to deactivate.
Send message to Slave (address) number
If you enter a slave number here and a message is triggered via the
Remote I/O or Parallel or Keyboard ports, the message will be sent
to the slave with the specified address. This attribute is valid for all
Run Modes. However, the slave address set when operating in the
Message/Variable/Slave Run Mode overrides this attribute.
Important: To send any message to a slave, Ports→RS-485
Port→Port Use must be set to DL Slaves.
If the Repeat message automatically attribute is active, the message
is sent to the slave each time it repeats. If the message has embedded
variables, it is sent to the slave each time new variable values are
received during the message wait time. Possible values for this field
include:
Entry:
Publication 2706-6.2
Which means:
0
Don’t send to slave
1 through 126
(addresses 13 & 18 are not valid)
127
Send to the single identified
slave address
Send to all slaves
Creating Message Files
4–27
Wait time for message
To the message display, this setting
can mean either:
• If you have activated Scroll message, the value here represents
the scrolling rate in tenths of a second. For example, a value of 8
here will result in display of the next new character in a message
every 0.8 seconds.
• If Scroll message is not active, then the value here represents the
number of seconds a message will appear on the message display.
For example, a value of 5 here will assure that the message will
appear on screen for 5 seconds whenever it runs.
A value of zero (0) allows the message to remain displayed until the
next message trigger is received. This allows the PLC or SLC to
control messaging times.
Acceptable values for this field can range from 0 through 31.
Clear message automatically
Sometimes referred to as AutoClear, activating this menu item
instructs the DL40 to clear the message from the display after the
Wait Time for message has expired even if no other messages have
been triggered.
This value applies only to the lines used by a single message. For
example, if this message uses only lines 2 and 3, then only lines 2
and 3 will be cleared. Lines 1 and 4 will remain unchanged.
Important: AutoClear de-energizes the alarm relay only if the
message which was cleared had energized the relay. A DL50
message display must always be sent a message that de-energizes the
relay.
Select Yes to activate or No to deactivate.
Repeat message automatically
This attribute (also referred to as AutoRepeat) causes the display to
repeat a message continuously as long as no other messages are in
the queue waiting to run. This attribute only functions if the DL40
message display is operating in the Message/Variable/Slave or
Message/Variable Run Mode.
Use this attribute when you need to update variables repeatedly
within a message.
Select Yes to activate or No to deactivate.
Publication 2706-6.2
4–28
Creating Message Files
Chain message to another
With this attribute you can link two messages together so that the
second message runs automatically after the Wait Time for the
message has expired. The second message requires no additional
triggering and no special modification of its attributes to respond.
Also, the link is independent of the second message, which means
that the second message can also run independently under other
circumstances.
The second message will have its own attributes, which may be
different from those of the first message. There is no limit to the
number of messages that can be chained together, and messages can
be chained to Special Messages.
Note: The Chain Message to Another attribute is disabled if
AutoRepeat is active.
Activate this attribute by entering a valid message number.
Energize relay
Activating this attribute will display the message and energize the
DL40 message display’s alarm relay whenever the message is
triggered.
Important: The alarm relay will not de-energize even after the Wait
Time for message has expired. The relay will de-energize when:
• a message is run for which the Energize relay attribute is not
activated
• any Special Message runs
• the DL40 message display leaves the Run Mode
Important: AutoClear de-energizes the alarm relay only if the
message which is cleared has the Energize relay enabled.
!
ATTENTION: Use the relay for annunciator purposes
only. Do not use it for control.
Select Yes to activate or No to deactivate.
Publication 2706-6.2
Creating Message Files
4–29
Send message to the stack
When a message is triggered, enabling this attribute places the
message number along with any variables on the Historical Events
Stack. Stacked messages can also be time stamped with the time the
message was triggered and/or run.
Important: Even if AutoRepeat is enabled, the message number
(and time) is placed on the Historical Events Stack only once each
time the message is triggered and/or run rather than each time it
repeats. The message number, variables, and time (if applicable) is
placed on the Historical Events Stack while the message is running
or repeating only when updates to variables are received by the
DL40.
For more information on the Historical Events Stack and time
stamping, refer to the DL40 Plus user manual (Publication 2706-6.1).
Select Yes to activate or No to deactivate.
Send message time to the stack
Enabling this attribute allows for time and date stamping of
messages sent to the Historical Events Stack.
Select Yes to activate or No to deactivate.
Hide message on display
When activated, the message does not appear on the DL40 Plus, but
is sent to a slave display, printer, tape recorder, or placed on the
Historical Events Stack. The other attribute settings for the message
determine its destination(s).
For example, assume Hide Message On Display is enabled, as are
Print Message and Send Message to Slave Number 2. There will be
no change on the DL40 display when the message runs, although a
copy of the message will be printed and it will be displayed on the
slave addressed as 2.
Note: When used with [CTRL][X] (ASCII Input Data), the
underscore prompt for this data will still be displayed on the DL40
message display even when Hide Message On Display is active.
Select Yes to activate or No to deactivate.
Acknowledge message
Enabling this attribute instructs the DL40 message display to hold
the message until you press the [MSG ACK] button on the front of
the DL40 display. The next message is displayed only after the
[MSG ACK] button has been pressed.
Publication 2706-6.2
4–30
Creating Message Files
Note: We recommend that you enable message queueing (from the
Options menu) when using the Acknowledge Message attribute.
Select Yes to activate or No to deactivate.
Slave message color
This attribute allows you to control the color of a message sent to a
color-capable slave display such as the Dataliner DL50 Tri-Color
Marquee Display. The setting options available to you include:
For DL10 or DL20
Default
For red DL50
For color DL50
Default
Default
Red
Green
Amber
Important: The factory setting for this attribute in the Message
Attribute Defaults menu is Default. We recommend leaving that
value unchanged. Do not use any selection other than Default for
DL10, DL20, or Red DL50 slave displays.
Note: This attribute is not available from the DL40 message display
onboard editor. It is only accessible through the Offline
Programming Software.
Slave message length
Use the Slave Message Length attribute only with DL50 slave
displays. Its purpose is to allow display of 10-character messages on
“short” DL50 displays operating in large text mode. Large text
mode displays characters that are 4.8 in. (12.2 cm) tall. Applicable
displays include Catalog No. 2706-F11J (Red DL50 Message
Display) and 2706-F11JC (Tri–color DL50 Message Display).
Acceptable values for this attribute include:
For DL10 or DL20
20
For DL50
20
10
The factory setting for the Slave Message Length attribute is 20,
which means the slave message length will always be set to 20 when
you create a message unless you have specified a new setting on the
Message Attribute Defaults menu.
Note: This attribute is not available from the DL40 message display
onboard editor. It is only accessible through the Offline
Programming Software.
Publication 2706-6.2
Creating Message Files
4–31
Echo relay to slave
The Echo Relay to Slave attribute sends the energize or de-energize
relay commands to the DL50 slave addressed in the Send Message to
Slave Number attribute. These commands are sent in addition to any
specified message text.
After this attribute sends a relay command to the slave, the slave
relay will not de-energize until another message is sent to the slave
that meets both of the following conditions:
• Energize Relay is set to No (to de-energize the relay)
• Echo Relay to Slave is set to Yes (to send a de-energize command
to the slave display)
Acceptable values for this attribute include:
For DL10 or DL20
No
For DL50
No
Yes
The factory setting for the Echo Relay to Slave attribute is No.
!
ATTENTION: Use the slave relay for annunciator
purposes only. Do not use it for control.
Note: This attribute is not available from the DL40 message display
onboard editor. It is only accessible through the Offline
Programming Software.
Notes
The attributes shown on the Message Attributes window are those
assigned to the message with the lowest message number currently in
the Message Picks list.
If Line Usage is other than All Lines, then the display line on the
DL40 does not necessarily correspond to the cursor row value shown
on the message editing window during editing.
To select a block of messages, move the cursor to the first message
on the block and press [CTRL][B] to mark the beginning of the
block. Then move the cursor to the last message in the block and
press [↵ ]. The entire block will be moved to the opposite column.
The Slave Message Color, Slave Message Length, and Echo Relay to
Slave message attribute selections are only available through the
Offline Programming Software. You cannot change those attributes
with the DL40 Onboard Editor.
Publication 2706-6.2
4–32
Creating Message Files
Message Attribute Default
Screen
Message Attribute Defaults are the attributes assigned to all
messages in a file when they are created.
After you have selected Message Attribute Defaults, the Message
Attribute Defaults window opens. Use the arrow keys to highlight
the attribute you want to change and press [↵ ]. Select the new
attribute value from a list, or enter a number. Press [↵ ] apply the
new attribute.
When you have finished setting attributes, move the cursor to Quit
and press [↵ ].
Message Attribute Default screen
Special Keys
You can use the following special keys on this screen.
↑
↓
Moves the cursor up or down the attribute list
↵
Lists or accepts attribute choices
Moves cursor to first attribute
Moves cursor directly to Quit
Get Online Help
Closes the Message Attribute Defaults window without taking
action.
Publication 2706-6.2
Creating Message Files
4–33
Notes
Refer to the previous section for descriptions of each message
attribute.
If Line Usage is other than All Lines, then the display line on the
DL40 does not necessarily correspond to the cursor row value shown
on the message editing window during editing.
To select a block of messages, move the cursor to the first message
on the block and press [CTRL][B] to mark the beginning of the
block. Then move the cursor to the last message in the block and
press [↵ ]. The entire block will be moved to the opposite column.
The Slave Message Color, Slave Message Length, and Echo Relay to
slave message attribute selections are only available through the
Offline Programming Software. You cannot change those attributes
with the DL40 Onboard Editor.
Publication 2706-6.2
4–34
Creating Message Files
Options Menu
The items on the Options menu allow you to control a variety of
hardware and display options. Contents of this menu include:
• Run Mode – Highlighting Run Mode and pressing [↵ ] opens a
window for choosing a run mode. Refer to Chapter 1 of this
manual for additional information on run modes.
• Newest Message on Line 1 – Selecting Yes displays the newest
message to be triggered on line 1, and shifts previously triggered
messages down. The message on the bottom line is shifted off
the display. This supersedes the message attribute Message on
Line # Only. Messages are still displayed in 20–character pieces.
This setting is effective with all run modes.
• Auto Run Message # – An Auto Run Message is a message that
will be displayed when your DL40 is powered up. It can be any
message, including a message in the Message List. The Auto
Run Message does not support inserted variable data. Specify a
message number, or enter 0 for no Auto Run Message.
Note for Remote I/O units only: If communications between a
DL40 and a PLC are not established at startup, the Auto Run
Message displays only if Switch 8 on Switch Bank #2 (Last State)
is ON.
• Background Message Number – The Background Message runs
•
•
•
•
Publication 2706-6.2
for a minimum of 2 seconds after the last message triggered has
finished its display wait time. This message is displayed until a
valid message is triggered or until the Run Mode is exited.
The Background Message does not support inserted variable data.
Specify a message number, or enter 0 for no Background
Message.
Special Message Start Number – Special messages provide the
ability to monitor and control certain functions of the DL40.
These messages can occupy message numbers 1 through 16, 901
through 916, or be disabled. Specify your choice.
Message Queueing Enabled – Choosing Yes allows you to put
up to 20 messages in the Queue. These messages are displayed in
the order they are received as soon as the previous message has
completed running.
Note: If Message Queueing is turned Off, the queue size is set to
1, which permits only one (1) additional message trigger to be
received while the current message is being run or displayed.
Time Format – Choose between AM/PM or 24Hr (military style)
time display.
Language – Choose between English, International, or Cyrillic
text (DL40 Plus only). Refer to Appendix C.
Creating Message Files
4–35
Options Menu
Special Keys
Use the following special keys on this screen.
↑
↓
Moves the cursor up or down the attribute list
↵
Lists or accepts attribute choices
Moves cursor to first attribute
Moves cursor directly to Quit
Get Online Help
Closes the Message Attribute Defaults window without taking action.
Publication 2706-6.2
4–36
Creating Message Files
Ports Menu
The Ports menu allows you to control the communication settings for
DL40 Message Display. Select from RS-232, RS-485, or the
currently selected trigger port settings active file.
After you have selected Ports, the Ports menu opens. Use the arrow
keys to highlight a menu item and press [↵ ]. You can select a new
value from a list, or enter a number. Press [↵ ] to apply any changes.
The Ports menu
Special Keys
Use the following special keys on this menu.
↑
↓
Moves the cursor up or down the menu
↵
Lists or accepts choices
Moves cursor to first menu item
Moves cursor directly to Quit
Get Online Help
Closes the Ports menu without taking action.
Publication 2706-6.2
Creating Message Files
4–37
Notes
Important: The communications parameter settings selected here
must match the communications settings of the device that is
connected to the DL40 Message Display.
The following lists communications parameters and the choices
available for each. Refer to the DL40 Plus user manual (Publication
2706-6.1) for more information on setting RS-232 or RS-485 ports.
RS-232 Port Settings
The following settings are available from this menu item.
The default value appears in bold.
Parameter
Available choices
Baud Rate
300, 1200, 2400, 4800, 9600, 19200
Data Bits
7 or 8
Parity
None, Odd, Even
Handshaking
None, Software, Hardware
Port Use
DL40 Programmer, DL Slaves, Devices
Using Open Protocol
RS-485 Port Settings
The following settings are available from this menu item. The
default value appears in bold.
Parameter
Available choices
Baud Rate
300, 1200, 2400, 4800, 9600, 19200
Data Bits
7 or 8➀
Parity
None, Odd, Even➁
DL40 Programmer, DL Slaves, Devices
Using Open Protocol
➀ This setting should always be 8 if Port Use is set to Programmer.
Port Use
➁ This setting should always be None if Port Use is set to Programmer.
Important: Do not set Port Usage to DL Slaves or Devices Using
Open Protocol if downloading message files to the DL40 through the
RS-485 Port.
RS-232 Printer Settings
These are the settings of the RS-232 Port when the Print Stack or
Print Mode function is active. The following settings are available
from this menu.
Parameter
Available choices
Null Count
0 to 255
Width
20 to 132
Publication 2706-6.2
4–38
Creating Message Files
RS-232 Tape Recorder Settings
Note that RS-232 Tape Recorder Settings are valid only when
writing to or reading from a tape drive, and that communications to a
tape recorder can be made only via the RS-232 port.
Baud rate is the only modifiable parameter applicable while using a
tape recorder. Your choices are listed below. The default value
appears in bold.
Parameter
Baud Rate
Available choices
300, 1200, 2400, 4800, 9600
This setting will revert to normal RS-232 Port settings (described
above) when the Tape function is finished.
Triggering Port Settings
The parameters presented here will differ between Remote I/O and
Parallel Port versions of the DL40 Message Display. The following
settings are available from this menu item on Remote I/O units. The
default value appears in bold.
Parameter
Available choices
Message Format
Binary, BCD
Variable Format
Binary, BCD
Control-W Format
BCD, ASCII
Bit Trigger Priority Section
Size
Always Send Clock Data
0 to 31 words
Yes or No➀
➀ If selection is Yes, only clock data will be returned to a PLC no matter what
attributes are set or what data is requested.
The following settings are available from this menu item on Parallel
Port units. The default value appears in bold.
Parameter
Message Format
Binary, BCD
Variable Format
Binary, BCD
Control-W Format
BCD, ASCII
High True Logic
Yes or No
Using AC/DC Converter
Yes or No
Data Hold Time
40 to 255 msec➀ or 10 to 255 msec➁
➀ If using AC/DC Converter
➁ If not using AC/DC Converter
Publication 2706-6.2
Available choices
Creating Message Files
Verify Menu
4–39
After you have finished with the Messages, Options, and Ports
menus, you can use the Verify menu to display individual messages
on the DL40 to be sure their format is correct. You can even insert
binary, BCD, and ASCII variables into the message you are testing.
Important: The file for the message you want to test must exactly
match the Internal Application Memory of the DL40 Message
Display. To assure that is the case, you must download the file to the
DL40 before testing any message in that file.
Depending on whether you select RS-485 or RS-232
communications, you will follow one of two different paths through
the Verify menu. The basic steps for each communications protocol
appear below.
Verify
Path
Default/
Temporary
DL40 Port
Selection
RS–232
RS–485
COM Port
Selection/
Configuration
Download
to DL40
Download
to DL40
Address
Selection
Message
Selection
COM Port
Selection/
Configuration
Test
Message
Message
Selection
Test
Message
Highlight Verify, then press [↵ ]. To change communications
method, highlight DL40 Port and press [↵ ]. Select RS–232 or
RS–485 and press [↵ ]. Highlight Download to DL40 and press [↵ ].
Publication 2706-6.2
4–40
Creating Message Files
Verify Menu
Special Keys
Use the following special keys on the Verify menus.
↑
↓
Moves the cursor up or down the menu
↵
Lists or accepts choices
Moves cursor to first menu item
Moves cursor directly to Quit
Get Online Help
Closes the menu without taking action.
Publication 2706-6.2
Creating Message Files
4–41
Communications via RS–485
Test Message Selections (for RS-485 communications)
If communicating via RS-485, the Address Selections window
opens. Select the DL40 address; then press [↵ ]. If you need to
change your computer’s communications port parameters, highlight
Configure Port, and press [↵ ]. Select COM1 or COM2; press [↵ ].
The window opens. Set Computer Address and
Baud Rate. Note: To change Parity or Data Bits, return to Ports
menu.
Highlight Download (filename) and press [↵ ]. After file is
downloaded, you will return to the Verify window. Highlight Test
Message(s) on DL40; press [↵ ].
The Message Selections window opens. Highlight number of the
message you want to display and press [↵ ]. Answer Yes to Start
Testing Messages Now? Message is displayed on DL40. Press
[ESC] to end an Autorepeat message.
Publication 2706-6.2
4–42
Creating Message Files
Communications via RS–232
Test Message Selection Window (for RS-232 communications)
Communicating via RS–232, no Address Selection window opens.
To change your computer’s communications port parameters,
highlight Configure Port; press [↵ ]. Select COM1 or COM2; press
[↵ ]. The Configure Port window opens. Set the Baud Rate.
Note: To change Parity or Data Bits, return to the Ports menu.
Highlight Download (filename) and press [↵ ]. After file is
downloaded, you will return to the Verify window. Highlight Test
Message(s) on DL40 and press [↵ ]. Note: Handshake must be set to
None. See page 5–4.
The Message Selections window opens. Highlight the number of the
message you want to display and press [↵ ]. Answer Yes to Start
Testing Messages Now? The message will be displayed on the
DL40. Press [ESC] to end an Autorepeat message.
If your message contains variables, you must put in a value for the
variables when testing the message. When you answer Yes to Start
Testing Messages Now?, a message text window and an Enter
variable window for the first variable opens. Enter value for your
first variable; press [↵ ]. The window for your second variable
opens. Continue to enter values for all [CTRL][V] and [CTRL][W]
variables.
Note: Values for [CTRL][X] variables are entered into a message
using a keyboard while the message is displayed.
Message Text Window
When you answer Yes to Start Testing Messages Now? the message
text window shown opens and displays the message contents.
Publication 2706-6.2
Creating Message Files
4–43
Message Verification Window
To test message on a
slave, enter address
Test messages contain the following symbols:
$
• """ indicates a [Ctrl][X] data request
• ∼ ∼ indicates a [Ctrl] [V] inserted formatted variable
•
indicates a [Ctrl] [W] inserted ASCII or BCD variable
Publication 2706-6.2
4–44
Creating Message Files
Device Menu
The Device menu allows you to configure the Offline Programming
Software to match the type of DL40 receiving downloaded message
files. You can change the selected device at any time the Develop
Menu bar appears.
When selecting a new device for an existing file, you will receive
error messages if the new device is incompatible with the messages
in the file. For example, if a message in the file requires 4 display
lines, you will not be able to select a two-line DL40.
This menu automatically pops up after you create a new file, so you
need access this menu from the Develop Menu bar only if you need
to change the type of DL40 selected.
The variables making up a device specification include:
Variable
DL40 Type
Device Menu
Publication 2706-6.2
Available choices
Remote I/O or Parallel Port
Number of Display Lines
2 or 4
Application Memory Size
16k, 32k, 64k, or 128k
Creating Message Files
4–45
Special Keys
Use the following special keys on this menu.
↑
↓
Moves the cursor up or down the menu
↵
Lists or accepts choices
Moves cursor to first menu item
Moves cursor directly to Quit
Get Online Help
Closes the menu without taking action.
Publication 2706-6.2
Downloading/Uploading Message
Files
This chapter describes the functions available to you from the
Transfer menu. The options available from this menu provide the
tools needed to move files and data between the Offline
Programming Software and the devices to which it is connected.
To open the Transfer menu, use the right and left arrow keys to
highlight Transfer on the Main menu bar, then press [↵ ]
Section
Page
Transfer Menu
5–2
Downloading a File using RS-232 or RS-485
5–3
Uploading a File using RS-232 or RS-485
5–6
Downloading a File using Remote I/O (PassThrough)
5–8
Uploading a File using Remote I/O (Passthrough)
5–10
Creating a New Communications File
5–12
Modifying an Existing Communications File
5–16
Sending the Time and Date using RS-232 or RS-485
5–17
Writing a File to Tape
5–18
Reading a File From Tape
5–20
Publication 2706-6.2
5–2
Downloading/Uploading Message Files
Transfer Menu
Selecting Transfer on the Main menu bar displays the Transfer menu.
Transfer Menu
Special Keys
Use the following special keys on the Transfer menu or on any of the
submenus described in this chapter.
↓
↑
Move the cursor to the desired function
Move the cursor directly to the first menu item
Move the cursor directly to the last menu item (Quit)
↵
Selects the item highlighted by the cursor, opens the next
menu, or selects from a list of options
Closes the menu or screen and returns cursor to the previous
menu
Get Online Help
Notes
From the Transfer menu you can perform the following activities:
• upload or download a file using RS-232 or RS-485
• upload or download a file using Remote I/O via DH+ or Ethernet
PassThrough
• send the time to a DL40 using RS-232 or RS-485
• write or write a file to a tape recorder
You can transfer one file at a time to or from a DL40 or tape
recorder.
Publication 2706-6.2
Downloading/Uploading Message Files
Downloading a File using
RS-232 or RS-485
5–3
You can download one file at a time from the Offline Programming
Software to the DL40. When you select Download to DL40
(RS-232/RS-485), the Download window opens. Move the cursor to
DL40 Port and press [↵ ]. Select RS-232 or RS-485 from the
window and press [↵ ]. A message flashes briefly to indicate that the
Offline Programming Software is saving the setup file.
Download to DL40 screen (using RS-232 or RS-485)
Next move the cursor to Select File and press [↵ ]. A window opens
with the default directory in the upper left corner and a list of the
files found in that directory.
Use the arrow keys to move the cursor to the file you want to
download and press [↵ ]. If the name of the file you want to
download does not appear here, you may be using the wrong data
directory. Change the data directory by backing up and selecting
Directory on the Download to DL40 window. When you enter a
complete directory path in the Directory window the Offline
Programming Software uses that directory as a default for all file
activities. Override the Directory setting by typing another complete
data directory when naming files. Enter the directory in the format:
Drive:\Root\Subdir
When you have selected a file, the file name will appear in the Select
File field on the Download to DL40 menu.
If downloading via RS-485, the Address Selections/Address Picks
window opens after you have selected a file. All message addresses
in the selected file will appear in the Address Selections column.
Use the up and down arrow keys to highlight an address, then press
[↵ ] to move the address to the Address Picks column. After you
have moved all the addresses to be downloaded into the Address
Picks column, press [F10].
Publication 2706-6.2
5–4
Downloading/Uploading Message Files
To select a block of addresses, move the cursor to the first address on
the block and press [CTRL][B] to mark the beginning of the block.
Then move the cursor to the last address in the block and press [↵ ].
The entire block will be moved to the opposite column.
RS-485 Address Selections/Address Picks window
Use the following special keys on the Address Selections/Address
Picks window.
←
→
Moves the cursor to the Address Selections or Address
Picks column
↑
↓
Moves the cursor up or down within a column
↵
Moves the highlighted address from one column to the
other
Move the cursor directly to the first item
Move the cursor directly to the last item
Get Online Help
Accept address picks
Closes the Address Selections/Address Picks window
without taking action
When you have specified a file and (in the case of an RS-485
download) your desired addresses, the Select File window opens.
Publication 2706-6.2
Downloading/Uploading Message Files
5–5
The Offline Programming Software allows you to download a
complete message file or only the currently selected file’s
parameters. Specify which you want by selecting All or Parameters
in the Select Download Type field of the Download to DL40 menu.
Note: To use Verify you must select All in the Select Download
Type field.
To configure your computer’s communication port, select Configure
Port on the Download to DL40 menu, then press [↵ ]. Select COM1
or COM2, press [↵ ], and select a baud rate in the Configure Port
window.
Note: To change parity or data bits, return to the Develop→Ports
menu.
Important: The software warns you if the configuration of the
DL40 to which you are writing is different than the configuration of
the file you are downloading. Device type, number of lines, and
memory size must all match.
Select File screen
Currently
selected
filename
To use Verify you must select All
When you have finished with the Select File menu, move the cursor
to the line containing the currently selected file name and press [↵ ].
The Download confirmation appears. Select Yes to begin
downloading, or No or Quit to cancel the download and return to the
Select File menu.
Publication 2706-6.2
5–6
Downloading/Uploading Message Files
Uploading a File
using RS-232 or RS-485
You can upload one file at a time from a DL40 to the Offline
Programming Software. When you select Upload from DL40
(RS-232/RS-485), the Upload File from DL40 window appear.
Move the cursor to DL40 Port and press [↵ ]. Select RS-232 or
RS-485 from the window and press [↵ ]. A message will flash
briefly to indicate that the Offline Programming Software is saving
the setup file.
Upload File (via RS-232)
To configure your computer’s communication port, select Configure
Port on the Upload to DL40 menu, then press [↵ ]. Select COM1 or
COM2, press [↵ ], specify your computer’s address (if using
RS-485), and select a baud rate in the Configure Port window.
Note: To change parity or data bits, return to the Develop→Ports
menu.
If necessary, you can select Directory to change the currently
selected data directory for the uploaded files.
Publication 2706-6.2
Downloading/Uploading Message Files
5–7
Address Selections Screen when uploading via RS-485
If uploading via RS-485, the Address Selections window opens when
you select Upload File. Use the up and down arrow keys to highlight
an address, then press [↵ ] to select the highlighted address and
return to the Upload File from DL40 menu.
When you have finished making changes on the Upload File from
DL40 menu, move the cursor to the line containing the words
Upload File and press [↵ ]. The Upload confirmation appears.
Select Yes to begin uploading, or No or Quit to cancel the upload and
return to the Upload File from DL40 menu.
Publication 2706-6.2
5–8
Downloading/Uploading Message Files
Downloading a File using
Remote I/O (PassThrough)
You can download one file at a time from the Offline Programming
Software to the DL40. When you select Download to DL40 (Remote
I/O) and press [↵ ], the Download (Remote I/O) window appears.
Important: The DL40 must be operating in Block Transfer mode to
use Remote I/O PassThrough.
Download (Remote I/O) file selection screen
Move the cursor to Select File and press [↵ ]. The program displays
a brief message indicating it is searching for data files, then displays
the File Selections window. Use the cursor keys to highlight a file
name and press [↵ ]. When you do so, the Message Selections
window is replaced by an expanded version of the Download
(Remote I/O) window. Included in this window are the address
parameters of the currently selected communication (.UDU) file,
including DL40 Rack (address), DL40 Group (number), and PLC
Address. In addition, the window includes the Download
FILENAME item and menu choices allowing you to modify an
existing Communication File or create a new one.
Note: There is no default Communication File. You must create at
least one file to upload or download over Remote I/O via DH+ or
Ethernet.
Publication 2706-6.2
Downloading/Uploading Message Files
5–9
Download (Remote I/O) screen – expanded
When the settings on the expanded Download (Remote I/O) screen
are configured, move the cursor to the Download FILENAME line
and press [↵ ]. Answer Yes when asked if you want to start
downloading now. Before you download you will get one of the
following warnings, depending on the type and access settings of
your DH+ hardware device.
ATTENTION: Before the download begins, you will see
!
one of the following warnings. Which one you see depends
on the type and access settings of your DH+ or Ethernet
hardware device.
WARNING: Incorrect address selection could corrupt data
in a non-DL40 device. Verify that the correct
Communication File is selected.
WARNING: Incorrect address selection could corrupt data
in a non-DL40 device. Verify that the correct
Communication File is selected.
DH+ Network Access is set to Local.
WARNING: Incorrect address selection could corrupt data
in a non-DL40 device. Verify that the correct
Communication File is selected.
DH+ Network Access is set to Remote (Bridge)
– Local Address is __.
– Remote Bridge Address is __.
Be sure the selected communication file has the correct
address parameters, and change them if necessary before
continuing.
Note: When downloading via Remote I/O, Download Type is
automatically set to All. You can’t transfer Parameters only.
Publication 2706-6.2
5–10
Downloading/Uploading Message Files
Uploading a File using
Remote I/O (PassThrough)
You can upload one file at a time from the DL40 to the Offline
Programming Software. When you select Upload to DL40 (Remote
I/O), the Upload (Remote I/O) window appears.
Upload via Remote I/O screen
Included in this window are the address parameters of the currently
selected communication (.UDU) file, including DL40 Rack
(address), DL40 Group (number), and PLC Address. In addition, the
window includes the Upload File item and menu choices allowing
you to modify an existing Communication File or create a new one.
Note: There is no default Communication File. You must create at
least one file to upload or download over Remote I/O via DH+ or
Ethernet PassThrough.
When the settings on the Upload (Remote I/O) screen are as you
want, move the cursor to the Upload File line and press [↵ ].
Answer Yes when asked if you want to start uploading now. Before
you upload, one of the following warnings is displayed, depending
on the type and access settings of your DH+ hardware device.
Publication 2706-6.2
Downloading/Uploading Message Files
!
5–11
ATTENTION:Before the upload begins, you will see one of
the following warnings. Which one you see depends on the
type and access settings of your DH+ or Ethernet hardware
device.
WARNING: Incorrect address selection could corrupt data
in a non-DL40 device. Verify that the correct
Communication File is selected.
WARNING: Incorrect address selection could corrupt data
in a non-DL40 device. Verify that the correct
Communication File is selected.
DH+ Network Access is set to Local.
WARNING: Incorrect address selection could corrupt data
in a non-DL40 device. Verify that the correct
Communication File is selected.
DH+ Network Access is set to Remote (Bridge)
– Local Address is __.
– Remote Bridge Address is __.
Note: Be sure the selected communication file has the
correct address parameters, and change them if
necessary before continuing.
Publication 2706-6.2
5–12
Downloading/Uploading Message Files
Creating a New
Communications File
To specify a new Communication File, highlight Create
Communication File in either the Download (Remote I/O) or Upload
(Remote I/O) menus and press [↵ ]. You will be asked to specify a
file name. To create a file in another directory, highlight Directory
and press [↵ ] and the Program Data directory window will open.
Enter the directory in the form:
Drive:\Root\Subdir
Press [↵ ]. The Communication File window opens. Highlight the
parameter you want to set and press [↵ ]. Select parameter setting
and press [↵ ]. When you highlight Hardware Device and press [↵ ],
a window opens from which you can select the hardware device you
are using. Set device parameters.
Communications File screen
Note: For information on PLC and interface board types required
for PassThrough file transfers, refer to Chapter 2.
When you highlight an address parameter (DL40 Rack, DL40
Group, PLC Address), you will get the following warning:
ATTENTION: Incorrect address selection could corrupt
!
data in a non-DL40 device. Verify that the correct
Communication File is selected.
Parameter
Publication 2706-6.2
Acceptable values
DL40 Rack
0 to 76 (octal)
DL40 Group
0, 2, 4, or 6
PLC Address
0 to 77 (octal)
PLC Type
PLC–5/15/25/40/60
PLC-5/250
Downloading/Uploading Message Files
5–13
The DL40 Rack is the address assigned to the DL40 using DIP
Switch Bank #1 on the back of the DL40. Refer to the DL40 Plus
user manual (Publication 2706-6.1) for additional information.
The DL40 Group is the First I/O Group Number assigned to the
DL40 using DIP Switch Bank #1 on the back of the DL40
The PLC Address is the station number of the PLC-5 on the DH+
link to which the DL40 is attached. This address must match the
DIP switch settings on the PLC.
The PLC Type is the type of Allen-Bradley PLC-5 on the DH+ link
to which the DL40 is attached. Use the PLC-5/250 choice for a PLC
mounted in a Pyramid Integrator chassis.
Selecting a Hardware Device
As shown below, you can select from a number of hardware devices:
Hardware Device window
Your hardware device choices appear in a list.
Parameter
Hardware Device
Acceptable values
1784-KL①
1784-KT, KTX, PCMK①
1770-KF2②
1784-KT2③
ETHERNET
① DH+ Device
② DH+ Device, Serial Interface
③ DH+ Device, Microchannel Bus
Publication 2706-6.2
5–14
Downloading/Uploading Message Files
Setting Device Parameters for a DH+ Network
Additional transfer parameters may be necessary when you select
DH+ communications devices. For card numbers 1784-KT,
1784-KT2, 1784-KL, 1784-KTX, and 1784-PCMK devices, you
must specify the DH+ Connection Type and DH+ Network Access.
1784-KT, KTX, PCMK configuration screen for DH+ network
Parameter
DH+ Connection Type
DH+ Network Access
Acceptable values
Direct
Multidrop
Local
Remote (Bridge)
DH+ Connection Type
Select Direct if your programming computer and your PLC-5 are the
only devices on the DH+ link, or if there are multiple devices on the
link and your programming computer is the first or the last physical
device on the link.
Select Multidrop if there are multiple devices on the link and your
programming computer is not first or last physical device on the link.
DH+ Network Access
Select Local if the PLC to which the DL40 is attached is on the same
DH+ link as the programming computer.
Select Remote (Bridge) if the PLC to which the DL40 is attached is
on a separate DH+ link from the DH+ link to which your
programming computer is attached.
Publication 2706-6.2
Downloading/Uploading Message Files
5–15
If you select Remote (Bridge), then you must specify the Local and
Remote Bridge Addresses.
Parameter
Acceptable values
Local Bridge Address
0 to 376 (octal)
Remote Bridge Address
0 to 376 (octal)
The Local Bridge Address is the Data Highway address that you
assign to the module connecting the DH+ link on which your
programming computer resides to the Data Highway. This address
must match the settings of the DIP switches on the module.
The Remote Bridge Address is the Data Highway address that you
assign to the module connecting the DH+ link on which the PLC-5 to
which the DL40 is connected resides to the Data Highway. This
address must match the settings of the DIP switches on the module.
Setting Device Parameters for an Ethernet Network
Additional transfer parameters may be necessary when you select an
Ethernet communications device. For Ethernet devices, you must
specify the Routing, Pushwheel, and Channel.
Ethernet Parameters configuration screen
Parameter
Acceptable values
Routing
PLC 5E
5130-RM
5130-KA
Pushwheel
1 to 8
Channel
2
3
Publication 2706-6.2
5–16
Downloading/Uploading Message Files
IP Address
Specify an IP Address which is a decimal number from 0 through
255. Consult your network administrator to obtain an IP Address.
Routing
The Routing value will most often be set to a PCL 5E, which
indicates that the Remote I/O link is attached directly to the PLC
being addressed. Choose the 5130-KA or 5130-RM selections if you
are performing transfers via a PLC-5/250 in a Pyramid Integrator
chassis.
Pushwheel
A Pushwheel must be specified when the 5130-KA module has been
selected in the Routing field. This value should match the
configuration of the PLC-5/250.
Channel
You need to specify a Channel if you select either a 5130-KA or
5130-RM module. The value in this field should be either 2 or 3 as
previously selected on the PLC-5/250.
After all parameters are set, highlight Quit and press [↵ ].
Modifying an Existing
Communications File
Select Modify Communications File to change the parameters
specified for the currently selected communications file. The name
of the currently selected communications file appears in the Select
Communication File field at the top of the Download or Upload
menu.
When you select Modify Communications File, the Communication
File window opens. This window contains all the settings for the
currently selected communications file, which you can modify. Note
that when you save the modifications to an existing file, you
overwrite the previous contents of that file.
Publication 2706-6.2
Downloading/Uploading Message Files
Sending the Time and Date to
a DL40 Via RS-232 or RS-485
5–17
You can send your computer’s system time and date to the DL40.
When you select Send Clock to DL40 (RS-232/RS-485), the Send
Clock to DL40 DL40 menu will appear. Move the cursor to DL40
Port and press [O]. Select RS-232 or RS-485 from the window and
press [↵ ]. A message flashes briefly to indicate that the Offline
Programming Software is saving the setup file.
Send Clock To DL40 screen
To configure your computer’s communication port, select Configure
Port, then press [↵ ]. Select COM1 or COM2, press [↵ ], specify
your computer’s address (if using RS-485), and select a baud rate in
the Configure Port window.
Move the cursor to the line containing the words Send Clock and
press [↵ ]. The Send Clock confirmation appears. Select Yes to
begin, or No or Quit to cancel the download and return to the Send
Clock to DL40 menu.
If using RS-485, the Address Selections/Address Picks window
opens. All message addresses in the selected file will appear in the
Address Selections column. Use the up and down arrow keys to
highlight an address, then press [↵ ] to move the address to the
Address Picks column. After you have moved all the addresses to be
updated with new time and date into the Address Picks column, press
[F10].
To select a block of addresses, move the cursor to the first address on
the block and press [CTRL][B] to mark the beginning of the block.
Then move the cursor to the last address in the block and press [↵ ].
The entire block is moved to the opposite column.
Publication 2706-6.2
5–18
Downloading/Uploading Message Files
Writing a File to Tape
You can download one file at a time from the Offline Programming
Software to a tape recorder. When you select Write to Tape
Recorder, the Write To Tape window appears.
Write To Tape menu
Next move the cursor to Select File and press [↵ ]. The File
Selections window appears with the default directory in the upper
left corner and a list of the files found in that directory.
File Selections window
Publication 2706-6.2
Downloading/Uploading Message Files
5–19
Use the arrow keys to move the cursor to the file you want to
download to tape and press [↵ ]. If the name of the file you want to
download does not appear here, you may be using the wrong data
directory. You can change the data directory by backing up and
selecting Directory on the Write To Tape menu. When you enter a
complete directory path in the Directory window, the Offline
Programming Software uses that directory as a default for all file
activities. You can override the Directory setting by typing another
complete data directory when naming files. Enter the directory in
the format:
Drive:\Root\Subdir
When you have selected a file, the wording in the Select File field on
the Write To Tape menu will change to the word Write followed by
the file name you have selected. The writing confirmation appears.
Select Yes to begin, or No or Quit to cancel the download and return
to the Select File menu.
Write to Tape menus and screens
If you pressed Yes to begin writing to tape, the first Program Status
window appears. Make sure your tape recorder is ready and the tape
is rewound. Follow the instructions in the window, then press any
key to continue. The Program Status window appears, indicating
that the write has begun.
Publication 2706-6.2
5–20
Downloading/Uploading Message Files
Reading a File from Tape
You can upload one file at a time from a tape recorder to the Offline
Programming Software. When you select Read From Tape
Recorder, the Read From Tape window opens.
Read From Tape menus and screens
To configure your computer’s communication port, select Configure
Port, then press [↵ ]. Select COM1 or COM2, press [↵ ], and select a
baud rate in the Configure Port window.
When you have initiated the upload, the Reading File confirmation
appears. Select Yes to begin, or No or Quit to cancel the download
and return to the Read from Tape menu.
If you pressed Yes to begin reading from tape, the first Program
Status window appears. Make sure your tape recorder is ready and
the tape is rewound. Press the recorder’s READ FROM TAPE
button, then press any key to continue. The Program Status appears,
indicating that the write has begun.
After the file is uploaded, the Save Data File As window will open
showing the directory and filename of the uploaded file. You can
override the displayed data directory by typing another complete
data directory when naming files. Enter the directory in the format:
Drive:\Root\Subdir\Filename
Press [↵ ] to accept the new directory and file name.
Publication 2706-6.2
Getting Reports
This chapter describes the functions available to you from the
Reports menu. As its name implies, the options available from this
menu provide the tools needed to control the Offline Programming
Software’s reporting functions.
To open the Reports menu, use the right and left arrow keys to
highlight Reports on the Main menu bar, then press [↵ ].
Section
Page
Reports Menu
6–2
Select File Submenu
6–4
Configure Ports Submenu
6–5
Starting the Print Job
6–6
Publication 2706-6.2
6–2
Getting Reports
Reports Menu
Selecting Reports on the Main menu bar displays the Reports menu.
You can print one file at a time on your printer.
Highlight Select File, then press [↵ ]. A message will appear briefly
indicating that the software is looking for data files, then the File
Selections window will open showing a list of all Message Files
found under the current directory. Select the file you want to print,
then press [↵ ]. A message will appear briefly indicating that the
software is reading the data files, then the Select File menu appears.
Reports menu with File Selections pop–up window
Special Keys
You may use the following special keys on the Reports menu or on
any of the submenus described in this chapter.
↓
↑
Move the cursor to the desired function
Move the cursor directly to the first menu item
Move the cursor directly to the last menu item (Quit)
↵
Selects the item highlighted by the cursor, opens the next
menu, or selects from a pop-up list of options
Closes the menu or screen and returns cursor to the previous
menu
Get Online Help
Publication 2706-6.2
Getting Reports
6–3
Notes
Change data path directories by selecting Reports→Directory.
When you enter a directory path, the Offline Programming Software
uses that path as a default for all file activities. When creating a new
data path, specify the path in the format:
Drive:\Directory\Directory1\Directory2
You can change the directory path at any time the Reports menu is
displayed. The change becomes effective immediately.
Publication 2706-6.2
6–4
Getting Reports
Select File Submenu
In the Select File menu, move the cursor to the Report Type field and
press [↵ ]. The Report Type menu opens.
Select File menu
Options available to you on the Report Type window include:
Parameter
Acceptable values
System Attributes Printed
Yes or No
All Messages Printed
Yes or No
Message Attributes
Yes or No
When you have set the Report Type parameters to meet your needs,
press [↵ ] to accept your settings and close the Report Type menu.
Publication 2706-6.2
Getting Reports
Configure Ports Submenu
6–5
Choose Configure Port from the Select File and press [↵ ] to identify
and configure the communication port to which your printer is
connected. A window appears listing the ports available to you.
Use the up and down arrow keys to select a port and press [↵ ].
Depending on which type of port you select, one of two windows
open. One window allows you to set communication parameters for
a COM port, and the other allows you to set the parameters for an
LPT port.
Configure Ports menus
LPT Port
Configuration
COM Port
Configuration
The parameters for LPT ports include:
Parameter
Acceptable values
Null Count
0
Page Width
20 to 132
The parameters for COM ports include:
Parameter
Null Count
Page Width
Baud
Parity
Data Bits
Stop Bits
Handshake
Acceptable values
0
20 to 132
110, 150, 300, 600, 1200, 2400, 4800,
9600
None, Odd, Even
7 bits, 8 bits
1 bit, 2 bits
None, Software, Hardware
After setting the printer port options, press [END] or use the down
arrow key to move to the last line of the window and highlight Quit.
Press [↵ ] to close the Configure Port window and return to the
Select File menu.
Publication 2706-6.2
6–6
Getting Reports
Starting the Print Job
Publication 2706-6.2
Check to make sure your printer is properly connected and turned
ON. Move the cursor to the Print FILENAME line on the Select File
menu and press [↵ ].
Managing Message Files
This chapter describes the functions available to you from the Files
menu. On this menu you will find the tools you need to work with
application files.
From the File menu you can perform the following activities:
•
•
•
•
copy files from one directory to another
delete files
rename files
convert DL20 Message Display application files to make them
usable with a DL40
• change working directories
This chapter contains the following topics:
Section
Page
Files Menu
7–2
Select Files Menu
7–3
File Selections/File Picks Window
7–4
Copy File(s)
7–5
Delete File(s)
7–6
Rename File(s)
7–6
Convert DL20 File(s)
7–7
Publication 2706-6.2
7–2
Managing Message Files
Files Menu
Selecting Files on the Main menu displays the Files menu.
Files menu
Special Keys
Use the following special keys on the Files menu or on any of the
submenus described in this chapter.
↓
↑
Move the cursor to the desired function or up and down a
column in the File Selections/File Picks window.
←
→
In the File Selections/File Picks window, moves the cursor
from one column to the other
Move the cursor directly to the first menu item
Move the cursor directly to the last menu item (Quit)
↵
Selects the item highlighted by the cursor, opens the next
menu, or selects from a pop-up list of options
Closes the menu or screen and returns cursor to the previous
menu
Get Online Help
In the File Selections/File Picks window, accepts picks
Publication 2706-6.2
Managing Message Files
Select Files Menu
7–3
Before copying, deleting, renaming, or converting files you must
first select the files you want to affect. To do so, move the cursor to
Select File(s) and press [↵ ]. The Select File(s) menu opens. From
this menu choose from a list of:
• DL40 message files only
• communications files only
• all DOS files in the currently selected directory
If necessary, select Directory to change the currently selected data
path for the uploaded files.
Highlight one of the menu items and press [↵ ]. The File
Selections/File Picks window opens.
Select Files menu
Publication 2706-6.2
7–4
Managing Message Files
File Selections/File Picks
Window
After you have selected the file type you want from the Select File(s)
menu, the File Selections/File Picks window opens. Listed here are
all the files in the currently selected directory that match the file type
specified. Use the up and down arrow keys to highlight a file name,
then press [↵ ] to move the file name to the File Picks column. After
you have moved the names of all the files you want to work with into
the File Picks column, press [F10].
To select a block of file names, move the cursor to the first name on
the block and press [CTRL][B] to mark the beginning of the block.
Then move the cursor to the last file name in the block and press
[↵ ]. The entire block moves to the opposite column.
After you have moved the names of all the files you want to work
with into the File Picks column, press [F10] to accept your selection.
The File Selections/File Picks Column disappears, and the Files top
level menu reappears.
Note that you cannot copy, delete, rename, or convert files unless
you have selected at least one file name through the Select File(s)
menu. If a selection is currently in effect, you will see the small File
Picks window in the upper left corner of the screen listing the current
selections. The File Picks window appears only if you have selected
one or more files.
File Selections/File Picks window
Publication 2706-6.2
Managing Message Files
Copy File(s)
7–5
Copy File(s) lets you perform the following actions:
• copy a single file within the same directory. You must specify a
new filename for the copy.
• copy a single file to a different drive and/or directory. Specify a
new filename for the copy or retain the original filename. Two
copies of the file exist when the copy is completed.
• copy multiple files to a different drive and/or directory. Original
file names will always be retained when copying multiple files.
To copy the selected file(s), move the cursor to Copy File(s) and
press [↵ ]. The Copy Files window opens.
Copy Files window
File Picks pop-up window
indicates what files are
currently selected.
Copying single files
To copy your selection to a new drive and/or directory, type the
destination in the Copy Files window in the format:
Drive:\directory\filename
To copy your selection to the same drive and directory, you do not
need to specify a drive or directory. Instead, type only the new
filename in the Copy Files window in the format:
filename
Press [↵ ] to accept your destination and start the copy.
Copying multiple files
To copy your selections to a new drive and/or directory, type the
destination in the Copy Files window in the format:
Drive:\directory
Press [↵ ] to accept your destination and start the copy.
Publication 2706-6.2
7–6
Managing Message Files
Delete File(s)
To delete the currently selected file(s), move the cursor to Delete
File(s) and press [↵ ]. The File Delete confirmation window opens
Select Yes to begin deleting, or No or Quit to cancel the deletion and
return to the Files menu.
File Delete confirmation pop-up window
Rename File(s)
Rename File(s) lets you perform the following actions:
• rename a single file within the same directory.
• move a single file to a different drive and/or directory. You may
specify a new filename for the copy or retain the original
filename. Note that this is a move and not a copy. Only a single
copy of the file exists when the move is complete.
• move multiple files to a different drive and/or directory. Original
file names will always be retained when moving multiple files.
To rename or move the selected file(s), move the cursor to Rename
File(s) and press [↵ ]. The Rename Files window opens.
Rename File window
Publication 2706-6.2
Managing Message Files
7–7
Renaming or moving single files
To rename or move your selection to a new drive and/or directory,
type the destination in the Rename Files window in the format:
Drive:\directory\filename
To rename your selection without moving it, type only the new
filename in the Rename Files window in the format:
filename
Press [↵ ] to accept the new name.
Moving multiple files
To move your selections to a new drive and/or directory, type the
destination in the Rename Files window in the format:
Drive:\directory
Press [↵ ] to accept your destination and move the files.
Convert DL20 File(s)
Convert DL20 File(s) lets you perform the following actions:
• convert a single DL20 S Record file to a DL40 file residing in the
original directory. You may specify a new filename or retain the
original filename.
• convert a single DL20 S Record file to a different drive and/or
directory. You may specify a new filename for the converted file
or retain the original filename.
• convert multiple DL20 S Record files to DL40 files. Original
file names will always be retained, but the file name extension
will be changed to .MEM.
To convert the selected file(s), move the cursor to Convert DL20
File(s) and press [↵ ]. The Conversion Destination File window
opens.
Publication 2706-6.2
7–8
Managing Message Files
Conversion Destination File pop-up window
Converting single files
To convert your selection type the conversion destination in the
Conversion Destination File window in the format:
Drive:\directory\filename
Do not provide a file name extension. The Offline Programming
Software automatically adds the extension .MEM to the file name.
To convert your selection without moving it type only the new
filename in the Conversion Destination File window in the format:
filename
Do not provide a file name extension. The Offline Programming
Software automatically adds the extension .MEM to the file name.
Press [↵ ] to accept the new name.
Converting multiple files
To convert your selections to a new drive and/or directory, type the
destination in the Conversion Destination Files window in the
format:
Drive:\directory
Do not provide a file name extension. The Offline Programming
Software automatically adds the extension .MEM to the file name.
Press [↵ ] to accept your destination and move the files.
Publication 2706-6.2
Message Display Worksheets
Using the Worksheets
Use a photocopy of this worksheet to record the message number and
content of the messages you create with the Offline Programming
Software. For your convenience, we’ve provided worksheets for
both two-line and four-line versions of the DL40.
Two Line Worksheet
MESSAGE NUMBER __________
MESSAGE NUMBER __________
MESSAGE NUMBER __________
MESSAGE NUMBER __________
MESSAGE NUMBER __________
Publication XXXX-XX.X – April 1996
A–2
Message Display Worksheets
Four Line Worksheet
MESSAGE NUMBER __________
MESSAGE NUMBER __________
MESSAGE NUMBER __________
MESSAGE NUMBER __________
Publication XXXX-XX.X – April 1996
Cables
2706-NC12
Allen-Bradley 1784-T47 Laptop or
IBM Compatible
Serial Port Female DB-25* Connector
DL40 Serial Port
Female DB-9* Connector
DCD
DCD 1
TXD 2
RXD 3
DTR 4
8
3
2
20
RXD
TXD
DTR
COM 5
DSR 6
RTS 7
CTS 8
RI
9
7
6
COM
DSR
4
5
22
1
RTS
CTS
RI
Chassis
Ground
* Gender specified is for the cable connectors.
2706-NC13
DL40 Serial Port
FemaleDB-9* Connector
Allen-Bradley 6121 Computer, 1784-T47 Laptop,
1784-T60 or IBM AT Compatible
Serial Port Female DB-9* Connector
DCD
DCD 1
TXD 2
RXD 3
DTR 4
1
2
3
4
RXD
TXD
DTR
COM 5
DSR 6
RTS 7
CTS 8
9
5
6
COM
DSR
7
8
9
RTS
CTS
* Gender specified is for the cable connectors.
Publication 2706-6.2
B–2
Cables
2706-NC14
DL40 Serial Port
Female DB-9* Connector
Allen-Bradley 6120 Serial Port
Female DB-9* Connector
DCD 1
TXD 2
RXD 3
DTR 4
8
3
2
9
RXD
TXD
DTR
COM 5
DSR 6
RTS 7
CTS 8
9
7
6
COM
DSR
4
5
1
RTS
CTS
Chassis
Ground
DCD
* Gender specified is for the cable connectors.
2706-NC15
DL40 Serial Port or Allen-Bradley 6121
Computer or IBM AT Compatible
Female DB-9* Connector
DCD
DCD 1
TXD 2
RXD 3
DTR 4
8
3
2
20
RXD
TXD
DTR
COM 5
DSR 6
RTS 7
CTS 8
9
7
6
COM
DSR
4
5
1
RTS
CTS
Chassis
Ground
* Gender specified is for the cable connectors.
Publication 2706-6.2
Serial Port or Black Box LD-485A-MP
Converter Box Male DB-25* Connector
Cables
DL40 to Allen-Bradley
1770-SA or -SB Tape
Recorder
B–3
This cable must be assembled by the user.
DL40 Serial Port
Female DB-9* Connector
Allen-Bradley 1770-SA or -SB
Male DB-25* Connector
2
3
2
3
5
6
7
6
7
20
5
8
4
1
Chassis
Ground
* Gender specified is for the cable connectors.
Publication 2706-6.2
B–4
Cables
Publication 2706-6.2
ASCII Character Sets
ASCII Character Set
C–2
ASCII Character Sets
Extended ASCII Character Set
To enter an extended ASCII character, use the [ALT] key in combination
with the numeric keypad section on your keyboard. Hold down the
[ALT] key, then enter one of the decimal values found in the extended
ASCII character chart below. The selected character will appear in the
offline message window when you release the [ALT] key. Extended
ASCII characters are not available with the onboard editor.
Publication 2706-6.2
ASCII Character Sets
C–3
Cyrillic Character Set
The DL40 Plus Dataliner supports both Cyrillic and English alphabet
characters. The Cyrillic characters include the 32 standard Cyrillic
alphabetic characters. The English characters include the standard 26
English alphabet characters, numbers, and punctuation marks. Refer to
the Cyrillic character reference chart that follows for keycode
assignments.
Publication 2706-6.2
C–4
ASCII Character Sets
Accessing Cyrillic Characters
Russian language messages may be created and edited only within the
offline programmer. There are two ways to generate Cyrillic characters
using a standard IBM compatible keyboard. A full set of upper and
lower case characters can be generated in the Edit Message and Create
New Message screens of the offline programmer.
Using the Cyrillic character reference chart on the previous page, a
character can be entered by holding down the [ALT] key while
entering the decimal number corresponding to the desired character.
Releasing the [ALT] key displays the normal corresponding extended
ASCII character. When the message is downloaded to the DL40
Plus, the characters are converted to Cyrillic.
Note: The Cyrillic character set is only available on DL40 Plus
Dataliner message displays. The offline programmer displays a
warning message if you attempt to download a Cyrillic application to
a standard DL40 message display.
Publication 2706-6.2
ASCII Character Sets
C–5
International Character Set
To access the international character set, also called Latin Alphabet
No.1, use the [ALT] key in combination with the numeric keypad
section on your keyboard. Hold down the [ALT] key, then enter the
2-digit hexadecimal value found in the chart below. For example, to
enter &, you would hold down [ALT] then enter the value 26. The
normal corresponding ASCII character is displayed in the offline message
window when you release the [ALT] key. When you download the
message file to the DL40 Plus, the characters are displayed in the
international font. The international character set is not available with the
onboard editor.
Note: The International character set is only available on DL40 Plus
Dataliner message displays. The offline programmer displays a
warning message if you attempt to download an International
application to a standard DL40 message display.
Publication 2706-6.2
PLC-5 Data Pass–Through
Overview
This appendix describes how to use the DL40 Plus PLC-5
Pass-Through option to transfer message files on a Data Highway
(DH+) network. The PLC-5 transfers the data, there is no need to
connect separate wiring between the DL40 and host computer.
The following illustrates the Pass-Through function.
PLC-5
DH+ Network
DL40
Remote I/O Link
Data Pass-Through
DL40
DL40
Message files can either be:
•
•
Transferred from the DL40 to the host computer (Uploaded).
Transferred from the host computer to the DL40 (Downloaded)
Publication 2706-6.2
D–2
PLC-5 Data Pass–Through
System Requirements
To use the Pass-Through option, you need:
•
•
Series D or greater DL40
Revision frn 2.00 or greater Offline Programming Software.
The Pass-Through function operates with the following PLC-5s:
Applicable PLC Types
PLC Type
PLC-5/15
PLC-5/11
PLC-5/20
PLC-5/25
PLC-5/30
PLC-5/4O
PLC-5/6O
PLC-5/250
Series
B
A
A
A
A
A
B
All
Minimum Revision
Level
N
A
A
J
B
E
B
All
The host computer requires an interface card for the DH+ link.
The following interface cards are available:
Interface Boards and Modules for Host Computer
Catalog Number
1784-KTK 1
1784-KT
1784-KL
1784-KF2
1784-PCMK/B
Publication 2706-6.2
Description
2 Slot Interface Board
1/ Slot Interface Board
2
Interface Board for Allen-Bradley 1784-T45 or
1784-T47
Interface Module for PC-AT or compatible
PCMCIA Type II interface card for PC compatible notebook computers.
PLC-5 Data Pass–Through
Communications
File Setup
D–3
Setup Communication files using the following Offline
Programming Software screens:
•
•
Download to DL40 (DH+ and Remote I/O) setup screens
Upload from DL40 (DH+ and Remote I/O) setup screens
Note: The DL40 must be operating in Block Transfer mode when
using the Pass-Through feature.
!
ATTENTION: Incorrect Address selection could
corrupt data in a non-DL40 device. Verify that the
correct Communication File is selected.
To access the setup parameters for file transfers, select the Transfer
menu on the initial Main Menu screen as shown below.
↑
↓
Moves cursor to desired function.
Home Moves cursor directly to 1st function - Download, etc.
End
Moves cursor directly to last function -Quit.
CR
Selects function highlighted by cursor.
F1
Help
Publication 2706-6.2
D–4
PLC-5 Data Pass–Through
Downloading Files
You can send only one file at a time to a DL40 Plus. Select the
Transfer menu and highlight Download to DL40 (Remote I/O)
function; press [↵ ]. The Download (Over Remote I/O) window
opens. Select Message File to download and Communication File to
use.
Highlight Download <filename> press [↵ ]. Answer Yes when
asked if you want to Start Downloading Now?
Note: When downloading through Remote I/O, Download Type is
automatically set to All. You can’t just transfer Parameters.
Uploading Files
You can send only one file at a time from a DL40. Highlight Upload
from DL40 (Remote I/O) function; press [↵ ]. The Upload (Over
DH+ and Remote I/O) window opens. Select Message File to upload
and Communication File to use.
Highlight Upload <filename> press [↵ ]. Answer Yes when asked if
you want to Start Uploading Now?
Publication 2706-6.2
PLC-5 Data Pass–Through
Download to DL40
(Remote I/O) Submenu
Select Download to DL40 (Remote I/O) from the Transfer menu
to set up a communications file for download data Pass-Through.
↑
↓
Home or End
Upload from DL40
(Remote I/O Submenu)
D–5
Moves cursor to desired file.
CR
Accepts file to download.
Moves cursor to first or last file.
Esc
Returns to transfer
screen. No download.
Select Upload (Remote I/O) from the Transfer menu to set up an
upload communications file for upload data Pass-Through
↑
↓
Home or End
Moves cursor to desired file.
CR
Accepts file to download.
Moves cursor to first or last file.
Esc
Returns to transfer
screen. No download.
Publication 2706-6.2
D–6
PLC-5 Data Pass–Through
Creating a New
Communications File
Select Create Communications File on the DH+ and Remote I/O
upload or download menus to create a new communications file
When creating or modifying a communications file, you must
provide the following:
DL40 Rack (Address) 0 to 76 (octal). The rack address assigned to
the DL40 using DIP Switch Bank #1.
DL40 Group (Number) First I/O Group Number assigned to the
DL40 using DIP Switch Bank #1 on the back of the DL40. Select: 0,
2, 4 or 6.
PLC Address 0 to 77 (octal). The station number of the PLC-5 on
the DH+ link to which the DL40 is attached. This address must
match the DIP switch settings on the PLC.
PLC Type Select: PLC-5/15, 25, 40, 60 or PLC-5/250. For
PLC-5/11, 5/20 and 5/30, choose PLC Type = PLC-5/15, etc.
Programming Terminal Address 0 to 77 (octal). Station number
for the programming terminal on the DH+ link.
DH+ Hardware Device You will have to provide additional data
depending on the type of interface module.
Publication 2706-6.2
PLC-5 Data Pass–Through
Modifying Existing
Communication Files
D–7
Select Modify Communications File on the Remote I/O upload or
download menus to modify an existing communications file.
If you want to modify an already specified Communication File,
highlight Select Communication File on the file Transfer menu.
To modify a file from another directory, highlight Directory and
press [CR] and the Program’s Data Path window opens. Enter
directory in the format:
Drive:\Directory
Press [↵ ]. The File Selections window opens. Highlight file you
want to modify; press [↵ ]. Note: All Communication Files have
the suffix .UDU.
Highlight Modify Configuration File in the Download window and
press [↵ ]. The Communication File window opens.
Highlight parameter you want to modify and press [↵ ]. Select
parameter setting and press [↵ ]. When you highlight DH +
Hardware Device and press [↵ ] the <Device Type> window opens.
Set device parameters.
After all parameters are set, highlight Quit and press [↵ ].
Publication 2706-6.2
D–8
PLC-5 Data Pass–Through
Setup Information
Refer to the following set up parameters, when setting up
communications files.
1784-KL Interface Module Set Up Parameters
Use the following when setting up the Pass-Through function.
DH + Connection Type
Select: Direct if your programming computer and your PLC-5 are
the only devices on the DH+ link or if there are multiple
devices on the link and your programming computer is the
first or last (physical) device on the link.
Select: Multi-Drop if there are multiple devices on the link and your
programming computer is not first or last (physical) device
on link.
DH + Network Access
Select: Local if the PLC to which the DL40 is attached is on the
same DH+ link as your programming computer.
Select: Remote (Bridge) if the PLC to which the DL40 is attached is
on a separate DH+ link (connected by Data Highway) from
the DH+ link to which your programming computer is
attached.
If you are using remote DH+ networks, you must also supply:
Local Bridge Address
0 to 376 (octal)
The Data Highway address that you assign to the 1785-KA Module
connecting your computer’s DH+ link to Data Highway. This
address must match the DIP switch settings on the KA Module.
Remote Bridge Address
0 to 376 (octal)
The Data Highway address that you assign to the 1785-KA Module
connecting your PLC-5’s DH+ link to Data Highway. This address
must match the DIP switch settings on the KA Module.
Publication 2706-6.2
PLC-5 Data Pass–Through
D–9
1784-KT Interface Module Set Up Parameters
Use the following when setting up the Pass-Through function.
DH + Connection Type
Select: Direct if your programming computer and your PLC-5 are
the only devices on the DH+ link or if there are multiple
devices on the link and your programming computer is the
first or last (physical) device on the link.
Select: Multi-Drop if there are multiple devices on the link and your
programming computer is not first or last (physical) device
on link.
KT Address
The bit address that you assign to the 1784-KT Module using the
DIP switch on the module.
DH + Network Access
Select: Local if the PLC to which the DL40 is attached is on the
same DH+ link as your programming computer.
Select: Remote (Bridge) if the PLC to which the DL40 is attached is
on a separate DH+ link (connected by Data Highway) from
the DH+ link to which your programming computer is
attached.
If you are using remote DH+ networks, you must also supply:
Local Bridge Address
0 to 376 (octal)
The Data Highway address that you assign to the 1785-KA Module
connecting the DH+ link containing your programming computer to
Data Highway. This address must match the DIP switch settings on
the module.
Remote Bridge Address
0 to 376 (octal)
The Data Highway address that you assign to the 1785-KA Module
connecting the DH+ link containing your PLC-5 (to which the DL40
is attached) to Data Highway. This address must match the DIP
switch settings on the module.
Publication 2706-6.2
D–10
PLC-5 Data Pass–Through
1784-KTK1 Interface Module Set Up Parameters
Use the following when setting up the Pass-Through function.
DH + Connection Type
Select: Direct if your programming computer and your PLC-5 are
the only devices on the DH+ link or if there are multiple
devices on the link and your programming computer is the
first or last (physical) device on the link.
Select: Multi-Drop if there are multiple devices on the link and your
programming computer is not the first or last (physical)
device on the link.
KTK1 Address
The bit address that you assign to the 1784-KTK1 Module using the
DIP switch on the module.
KTK1 Interrupt
The interrupt that you assign to the 1784-KTK1 Module using the
jumper on the module. The factory setting for this interrupt is IRQ5.
1770-KF2 Interface Module Set Up Parameters
Use the following when setting up the Pass-Through function.
Configure Port
The computer port to which the KF2 Module is attached.
Select:
COM1 or COM2
Baud Rate
300, 600, 1200, 2400, 4800, 9600
Parity
None, Even, Odd
Duplex
Half, Full
Error Checking
CRC, BCC
These parameters must match the settings for the KF2 Module.
Publication 2706-6.2
Symbols
.INI file, 2–8
Block Transfer Mode, during download, 5–8
Buffers, 2–3
.UDU file, 5–10
[CTRL][A], 4–24
C
[CTRL][F], 4–13
Cables, offline programming, 1–5
[CTRL][T], 4–15
Capabilities, 1–4
[CTRL][V], 4–12
[CTRL][W], 4–13
Chain messages, 1–9, 4–28
with AutoRepeat, 4–28
[CTRL][X], 4–14, 4–29, 4–42
Change formatted variable, 4–13
[MSG ACK], 4–29
Changing Message Attributes, 4–24, 4–32
Channel, 5–15, 5–16
A
Acknowledge message, 4–29
and message queueing, 4–30
Address Selections screen, 5–7
Character Sets
Cryillic, 1–6
Cyrillic, 1–3
English, 1–3, 1–6
International, 1–3, 1–6
Address Selections/Address Picks window,
5–4
Checkdisk command, 2–2
Alarm relay, 4–28
Clock, data, 1–7
Alarms, 1–8
relay, 1–8
Color monitor, 3–4
All lines, 4–31, 4–33
Communication
options, 1–2
PLC5 Remote I/O PassThrough, 1–13
port settings, 1–2
RS–232, 1–2
RS–485, 1–2
slave, 1–2
Arrow keys, 4–4
ASCII data, 1–6
request for, 4–14
word length, 4–13
ASCII variable, insert, 4–13
Attributes, priority of, 4–31
Auto run message #, 4–34
AutoClear, 4–27
with relay, 4–28
Clear message automatically, 4–27
Color slave, 4–30
Communications File screen, 5–12
Communications parameters, 4–37, 5–5,
5–8, 5–10, 5–17, 5–20
Compound variables, 4–13
AUTOEXEC.BAT file, 2–11
CONFIG.SYS file, 2–3, 2–11
AutoRepeat, 4–28
Configuration, options, 1–4
Auxiliary devices, 1–8
Configure Ports menu, 6–5
Conversion Destination pop-up, 7–8
B
Copy (Message), rules governing, 4–18
Background message, 1–9
Copy (Messages) Screen, 4–17
Background message number, 4–34
Copy Files pop-up, 7–5
Backup, 1–6
Create New Message, 4–16
BCD data, 1–9
word length, 4–13
Create New Message screen, 4–16
BCD variable, insert, 4–13
Cursor, 3–2
Binary Coded Decimal data. See BCD data
Binary data, 1–9
Creating a new file, 4–5
I–2
Index
D
E
Data mode, 1–9
Echo relay to slave, 4–31
Data Path, 4–3, 4–6
Editing rules, 4–11, 4–23
Data Path Directory window, 4–6
Embedded variables, 1–9
Date, 1–7
insert in message, 4–15
Error messages, 4–44
Date & Time, 3–2
setting, 3–5
Ethernet Parameters Configuration screen,
5–15
Date variable, length in characters, 4–15
Exiting the program, 3–7
Ethernet parameters, 5–15
Debug mode, 1–8
Delete (Message) screen, 4–19
Delete Message confirmation pop-up, 4–19
F
Develop Menu, 4–2
File
.UDU, 5–10
creating new, 4–5
Develop Screen Menu bar, 4–7
File Delete Pop-up, 7–6
Device, for PassThrough file transfers, 5–13
File Selections pop-up, 6–2
Device menu, 4–44
File Selections screen, 4–4
Device specification, 4–44
File Selections/File Picks pop-up, 7–4
Devices, auxiliary, 1–8
File transfer, hardware, 1–13–1–15
DH+, 1–13
File transfers, with PassThrough, 5–8
DH+ Configuration screen, 5–14
Format, time, 4–34
DH+ connection type, 5–14
Formatted variable, 4–12
vs. unformatted variable, 4–12
Deleting messages, 4–19
DH+ network access, 5–14
DH+ parameters, 5–14
Directory, 4–3, 4–6
Display message on what line, 4–26
H
Displaying new messages, 4–34
Hardware, required for file transfer,
1–13–1–15
Distance, viewing, 1–3
Hardware device, 5–13
DL10 display, 4–30
Hardware Device Pop-up, 5–13
DL20 display, 4–30
Hardware versions, 1–1
DL40, versions, 1–1
Help Screen, 3–3
DL40 Group, 5–13
Hidden messages, 1–9
DL40 Rack, 5–13
Hide message on display, 4–29
DL50 Marquee Display, 4–30
Historical Events Stack, 4–29
overview, 1–7
DOS Path, 4–3, 4–6
Download, verify, 5–5
Download (Remote I/O) screen, 5–8
I
Download to DL40 screen, 5–3
Incrementing message numbers, 4–18, 4–21
Downloading files, Block Transfer Mode, 5–8
Insert ASCII or BCD Variable, 4–13
Insert date, 4–15
Insert time, 4–15
INTERCHANGE, 2–6
Publication 2706–6.2
Index
K
Keyboard, port, 1–8
Keys
arrow, 4–4
shortcut, 3–6, 3–7
special, 3–6, 4–11, 4–23
L
Line usage, 4–31, 4–33
Line usage setting, 4–15, 4–16
Local Bridge, 5–15
M
Main Menu bar, 3–2
I–3
defined, 4–25
for new messages, 4–16
priority of, 4–31
with variables, 4–15
Message chaining, 4–28
disabled with AutoRepeat, 4–28
Message number
assigned during copy, 4–17, 4–20
background, 4–34
duplicate, 4–16, 4–18
Message Queueing, 4–34
Message Selection/Message Picks Pop-up,
4–17, 4–19, 4–20, 4–22, 4–24, 4–32
Message Selections, 4–17, 4–19, 4–20,
4–22, 4–24, 4–32
Message Selections pop-up, 4–9
Main screen, 3–2
Message Selections/Message Picks pop-up,
4–17
Marquee Display, 4–30
Message Text window, 4–10, 4–16
MEM command, 2–2
Message time, sending to stack, 4–29
MEMMAKER command, 2–3
Message Verification pop-up, 4–43
Memory, management of, 2–3
Messages
background, 1–9
chaining, 1–9
copying, 4–17
deleting, 4–19
error, 4–44
hidden, 1–9
incrementing numbers, 4–18, 4–21
memory, 2–2
renumbering, 4–20
selecting multiple, 4–18, 4–19, 4–21,
4–31, 4–33
special, 1–12
support, 1–3
too many messages, 4–16, 4–18
Menu
Configure Ports, 6–5
Develop, 4–2
Device, 4–44
Messages, 4–8
Options, 4–35
Ports, 4–36
Read From Tape, 5–20
Reports, 6–2
Select File, 6–4
Select Files, 7–3
Setup, 3–4
Verify, 4–40
Write to Tape, 5–18
Menu bar
Develop Screen, 4–7
Main Menu, 3–2
Messages Menu, 4–8
Menu choice, 3–2
Monitor type, 3–4
Menu Title, 3–2
Monochrome monitor, 3–4
Message
sending to stack, 4–29
System Attribute Warning, 4–7
Multidrop Mode, 5–14
Message Attribute Defaults, 4–32
N
Message Attribute Defaults screen, 4–32
Message Attribute pop-up, 4–24
Mode, 1–11
Modify Message Attributes screen, 4–24
New messages, 4–34
message attributes with, 4–16
Message attributes
Publication 2706–6.2
I–4
Index
O
Offline Programming Software, 1–2, 1–5
for slave display, 4–26
RS-232, 4–37
RS-485, 4–37
triggering, 4–38
Onboard Editor, 1–6
modifying port settings, 1–2
Ports, report configuration, 6–5
Onboard editor, 4–30, 4–31, 4–33
Ports menu, 4–36
Operating modes, 1–11
Print message, 4–26
Options menu, 4–35
Printer port settings, RS-232, 4–37
Printers, 1–8
P
Parallel port
PLC communications, 1–6
summary, 1–1
Parallel port units, 4–38
Parameters
communication, 5–5
communications, 5–8, 5–10, 5–17, 5–20
for DH+ PassThrough file transfers, 5–14
Printing, 1–2, 1–8
Priority of message attributes, 4–31
Prompt, underscore, 4–29
Protocol
open, 1–2
slave, 1–2
Pushwheel, 5–15, 5–16
Q
PassThrough file transfers, 1–13, 1–14, 5–8
PassThrough processing, hardware,
1–13–1–15
Queue, enabling, 4–34
Quitting the program, 3–7
PATH, 4–3, 4–6
PLC Address, 5–13
R
PLC Type, 5–13
PLC-5, with DH+, 5–15
PLC5 Remote I/O Pass Through, 1–13
PLC-5/250, with Ethernet, 5–16
Pop-up
Address Selections/Address Picks, 5–4
Conversion Destination, 7–8
Copy Files, 7–5
Create New File, 4–5
Data Path Directory, 4–6
Delete Message confirmation, 4–19
File Delete, 7–6
File Selections, 6–2
File Selections/File Picks, 7–4
Hardware Device, 5–13
Message Selections, 4–9
Message Selections/Message Picks, 4–17
Message Verification, 4–43
Rename File, 7–7
Start/Increment, 4–17
Text Message Selections
RSĆ232, 4-42
RSĆ485, 4-41
Publication 2706–6.2
Read From Tape menus & screens, 5–20
Relay, 4–28
echo to slave, 4–31
with AutoClear, 4–28
Remote (Bridge), 5–14
Remote I/O
ASCII data, 1–6
summary, 1–1
Remote I/O units, 4–38
and Auto Run, 4–34
Rename File pop-up, 7–7
Renumber (Message), rules governing, 4–21
Renumbering messages, 4–20
Repeat message, 4–26
Repeat message automatically, 4–27
Repeating messages, 4–27
Reports, type, 6–4
Reports menu, 6–2
Request for ASCII data, 4–14
Port
keyboard, 1–8
RS–232, 1–2
RS–485, 1–2
Requirements
hardware, 2–1
memory, 2–2
Port settings
RS–232
Routing, 5–15, 5–16
Index
port settings, 1–2
port usage, 1–7
Setup Menu, 3–4
Shortcut keys, 3–6, 3–7
RS–485
port settings, 1–2
port usage, 1–7
Slave, echo relay to, 4–31
RS-232, testing messages via, 4–42
Slave display, 1–8, 4–30
Port settings for, 4–26
RS-232 port settings, 4–37
RS-232 printer port settings, 4–37
RS-232 tape recorder settings, 4–38
RS-485, testing messages via, 4–41
RS-485 port settings, 4–37
Run mode, 1–11–1–14, 4–34
S
Screen
Address Selections, 5–7
Communications File, 5–12
Copy (Messages), 4–17
Create New Message, 4–16
Delete (Message), 4–19
Delete (Messages), 4–19
DH+ Configuration, 5–14
Download (Remote I/O), 5–8
Download to DL40, 5–3
Ethernet Parameters Configuration, 5–15
File Selections, 4–4
Main, 3–2
Message Attribute Defaults, 4–32
Modify Message Attributes, 4–24, 4–32
Read From Tape, 5–20
Renumber (Messages), 4–20
Select File, 5–5
Send Clock to DL40, 5–17
Text Search, 4–22
Upload File from DL40, 5–6
Upload Via Remote I/O, 5–10
Slave devices, 4–37
Slave message color, 4–30
Slave message length, 4–30
Slaves, communications with, 1–2
Special keys, 3–6, 4–11, 4–23
Special messages, 1–12, 4–34
Specifying a device, 4–44
Stack
Historical Events, 4–29
sending message time to, 4–29
Stacks, 2–3
Start number of special messages, 4–34
Start/Increment pop-up, 4–17
System Attribute Warning message, 4–7
T
Tape recorder, RS-232 port settings, 4–38
TCP/IP, 2–11
Testing messages
via RS–485, 4–41
via RS-232, 4–42
Text Message Selections pop-up
RS-232, 4–42
RS-485, 4–41
Text Search screen, 4–22
Time, 1–7
insert in message, 4–15
Scroll message, 4–26, 4–27
Time & Date, setting, 3–5
Searching for text, 4–22
Time format, 4–34
Select File menu, 6–4
Time variable, length in characters, 4–15
Select File screen, 5–5
Triggering port settings, 4–38
Select Files menu, 7–3
Selecting a block of messages, 4–18, 4–19,
4–21, 4–31, 4–33
Send Clock to DL40 screen, 5–17
Send message time to the stack, 4–29
Send message to slave, 4–26
Send message to the stack, 4–29
Setting time & date, 3–5
Settings, communications, 4–37
I–5
U
Underscore prompt, 4–29
Upload File from DL40 screen, 5–6
Upload Via Remote I/O screen, 5–10
V
Variable, formatted, 4–12
Publication 2706–6.2
I–6
Index
Variable data, message attributes with, 4–15
Warning Light, 1–8
Variables, 4–12
compound, 4–13
embedded, 1–9
Verify, during download, 5–5
Window
Create New File, 4–5
Data Path Directory, 4–6
Message Text, 4–10, 4–16
Verify menu, 4–40
Word length, ASCII or BCD data, 4–13
Viewing distance, 1–3
Write to Tape menu, 5–18
W
Wait time for message, 4–27
Publication 2706–6.2
.
Rockwell Automation helps its customers receive a superior return on their investment by bringing
together leading brands in industrial automation, creating a broad spectrum of easy-to-integrate
products. These are supported by local technical resources available worldwide, a global network
of system solutions providers, and the advanced technology resources of Rockwell.
Worldwide representation.
Argentina • Australia • Austria • Bahrain • Belgium • Bolivia • Brazil • Bulgaria • Canada • Chile • China, People’s Republic of • Colombia • Costa Rica • Croatia • Cyprus
Czech Republic • Denmark • Dominican Republic • Ecuador • Egypt • El Salvador • Finland • France • Germany • Ghana • Greece • Guatemala • Honduras • Hong Kong
Hungary • Iceland • India • Indonesia • Iran • Ireland • Israel • Italy • Jamaica • Japan • Jordan • Korea • Kuwait • Lebanon • Macau • Malaysia • Malta • Mexico • Morocco
The Netherlands • New Zealand • Nigeria • Norway • Oman • Pakistan • Panama • Peru • Philippines • Poland • Portugal • Puerto Rico • Qatar • Romania • Russia • Saudi
Arabia • Singapore • Slovakia • Slovenia • South Africa, Republic of • Spain • Sweden • Switzerland • Taiwan • Thailand • Trinidad • Tunisia • Turkey • United Arab Emirates
United Kingdom • United States • Uruguay • Venezuela
Rockwell Automation Headquarters, 1201 South Second Street, Milwaukee, WI 53204-2496 USA, Tel: (1) 414 382-2000 Fax: (1) 414 382-4444
Rockwell Automation European Headquarters, Avenue Hermann Debroux, 46, 1160 Brussels, Belgium, Tel: (32) 2 663 06 00, Fax: (32) 2 663 06 40
Rockwell Automation Asia Pacific Headquarters, 27/F Citicorp Centre, 18 Whitfield Road, Causeway Bay, Hong Kong, Tel: (852) 2887 4788, Fax: (852) 2508 1846
World Wide Web: http://www.ab.com
Publication 2706-6.2– November 1998
41061-091-01(A)
Copyright 1998 Allen-Bradley Company, Inc. Printed in USA
">