Page 1 of 23 of Tender SGI7516P16 dated 15.06

Page 1 of 23 of Tender SGI7516P16 dated 15.06
OIL INDIA LIMITED
( A Government of India Enterprise )
P.O. Udayan Vihar -781171
Guwahati, Assam(India)
OIL INDIA LIMITED invites Local Competitive Bid (LCB) under Two Bid System through its eProcurement portal https://etender.srm.oilindia.in/irj/portal for the following item:
e-Tender no. /
Material Description
B. C. Date
SGI7516P16
Procurement, Installation, Commissioning , Testing and Handing over
B.C. Date:
of Generating Set, Control Panel, Distribution panel
06.08.2015
Tender fee (Non-refundable) : Rs. 1000.00; Bid Closing/Opening Time: (11:00Hrs)IST/(14:00Hrs)IST;
Period of sale of documents: 22.06.2015 to one week prior to bid closing date. The complete bid documents
and details for purchasing bid documents, participation in E-tenders are available on OIL’s e-procurement
portal https://etender.srm.oilindia.in/irj/portal as well as OIL’s website www.oil-india.com.
NOTE: All addenda, Corrigenda, time extension etc, to the tenders will be hosted on above website and eportal only and no separate notification shall be issued in the press. Bidders should regularly visit above
website and e-portal to keep themselves updated.
Note: A Pre-Bid Conference against above tender will be held in Guwahati,
Assam on 21st July , 2015.
Page 1 of 23
of Tender SGI7516P16 dated 15.06.2015
OIL INDIA LIMITED
(A Government of India Enterprises)
PO : Udayan Vihar – 781171
Guwahati, Assam (India)
TELEPHONE NO. (91-361)2643685/688
FAX NO: (91-361) 2643686
Email: panchali@oilindia.in ; erp_mm@oilindia.in
FORWARDING LETTER
Tender No & Date
: SGI7516P16 dated 15.06.2015
Tender Fee
: Rs 1,000.00
Bid Security Amount
: Rs. 2, 19, 700.00
Bidding Type
: SINGLE STAGE TWO BID SYSTEM
Bid Closing on
: As mentioned in the Basic Data of e-portal
Bid Opening on
:
Performance Guarantee
:
Integrity Pact
: Applicable
-doApplicable
OIL invites Bids for Procurement, Installation, Commissioning , Testing and Handing over of Generating Set,
Control Panel, Distribution panel through its e-Procurement site under SINGLE STAGE TWO BID
SYSTEM.
The general details of tender can be viewed by opening the eRFx [Tender] under RFx and Auctions. The
details of items tendered can be found in the Item Data and details uploaded under Technical RFX. The
bidding document is available in the Technical RFx -> External Area - > Tender Documents.
NOTES:
(1) A Pre-Bid Conference with the Parties will be held in Guwahati (India) on 21st th & 22nd July , 2015 to discuss
on the technical specifications and other terms and conditions of the tender. All the Parties who purchase the
Bidding Document within the closing date of sale of the tender will be eligible to attend the Pre-Bid Conference.
The exact venue and time of the Pre-Bid conference will be intimated to the Parties at a later date.
(2) Clarification on the technical specifications and other terms & conditions of the Generating Set, Control Panel,
Distribution panel shall be provided to the parties during the Pre-bid Conference. Parties should come fully prepared
to the Pre-bid Conference and submit their queries to OIL in the Pre-bid Conference for clarification. The set of
queries in ‘Word format’ may also be sent to OIL at least 7 (seven) days before the Pre-bid Conference for study by
OIL. OIL will not be responsible for non-receipt or late receipt of any bidder’s query in OIL’s office.
(3) Any changes in the technical specifications and other terms & conditions of the Generating Set, Control Panel,
Distribution panel arising out of discussion in the Pre-bid Conference shall also form part of the bidding document.
(4) At the most 2 (two) representatives from each prospective bidder shall be allowed to participate in the pre-bid
conference. All costs for attending the pre-bid conference shall be to prospective bidders’ account.
Page 2 of 23
of Tender SGI7516P16 dated 15.06.2015
(5) Parties, immediately after the purchase of the bidding documents, shall inform OIL at the following address
about their participation in the Pre-Bid Conference with details of the persons to enable OIL to make arrangement
for the Pre-Bid Conference.
CHIEF MATERIALS MANAGER
OIL INDIA LIMITED (PIPELINE HEADQUARTER )
P.O UDAYAN VIHAR, PIN – 781171,GUWAHATI
ASSAM, INDIA
FAX NO. : +91 - 361 – 2643686
E-Mail : oilmatpl@oilindia.in
panchali@oilindia.in
Standard Notes:
1.0 The tender will be governed by “General Terms & Conditions” for e-Procurement as per
Booklet No. MM/LOCAL/E-01/2005 for E-Procurement LCB Tenders.
2.0 This Bidding document consists of :
Technical specifications and Quantity as per Annexure – AAA,
Bid Rejection & Bid Rejection Criteria as per Annexure-BBB
Technical bid check list as per Annexure –EEE ,
Response sheet as per Annexure -FFF and
Bank Details as per Annexure-GGG.
Integrity Pact (Annexure-DDD), Vendor User Manual and LCB Doc Booklet (revised) have been
uploaded separately in the Technical RFx -> External Area - > Tender Documents
3.0
The tender shall also be governed by the Bid Rejection & Bid Evaluation Criteria given in
enclosed
4.0
Annexure-BBB. However, if any of the Clauses of the Bid Rejection Criteria / Bid Evaluation
Criteria (as per Annexure-BBB) contradict the Clauses of the tender and / or “General Terms &
Conditions” as per Booklet No. MM/LOCAL/E-01/2005 for E-procurement (LCB Tenders) elsewhere,
those in the BEC / BRC shall prevail.
5.0 Bidder are advised to fill up the Technical bid check list (Annexure EEE) , Response sheet
(Annexure FFF) and Bank Details (Annexure GGG) given in the bidding document uploaded in
Technical RFx -> External Area - > Tender Documents. The above filled up documents to be uploaded in
the Technical RFX Response.
6.0 Please do refer the User Manual provided on the portal on the procedure ‘How to create Response’
for submitting offer.
6.0
In case of SINGLE STAGE-TWO BID SYSTEM, bidders shall prepare the “Techno-commercial
Unpriced Bid” and “Priced Bid” separately and shall upload through electronic form in the OIL’s eTender portal within the Bid Closing Date and Time stipulated in the e-Tender. The “Techno-commercial
Unpriced Bid” shall contain all technical and commercial details except the prices which shall be kept
blank. Details of prices as per Bid format / Commercial bid to be uploaded as attachment in the
Attachment Tab “Notes and Attachments”.
6.1
A screen shot in this regard is given below.
Any offer not complying with above submission procedure will be rejected as per Bid Rejection Criteria
mentioned in the tender.
Page 3 of 23
of Tender SGI7516P16 dated 15.06.2015
Go to this Tab “Technical RFx
Response” for Uploading “Technocommercial Unpriced Bid”.
Go to this Tab “Notes and
Attachments” for Uploading
“Priced Bid” files.
On “EDIT” Mode- The following screen will appear. Bidders are advised to Upload “TechnoCommercial Unpriced Bid” and “Priced Bid” in the places as indicated above:
Bid on “EDIT” Mode
Area for uploading TechnoCommercial Unpriced Bid*
Area for uploading Priced
Bid**
Note :
*
**
6.2
The “Techno-Commercial Unpriced Bid” shall contain all techno-commercial details except the prices.
The “Price bid” must contain the price schedule and the bidder’s commercial terms and conditions. For
uploading Price Bid, first click on Sign Attachment, a browser window will open, select the file from the
PC and click on Sign to sign the file. On Signing a new file with extension .SSIG will be created. Close that
window. Next click on Add Atachment, a browser window will open, select the .SSIG signed file from the
PC and name the file under Description, Assigned to General Data and click on OK to save the File.
IMPORTANT NOTE : NO PRICE SHOULD BE INDICATED IN TECHNICAL BID
Priced bids of only those bidders will be opened whose offers are found to be technocommercially acceptable.
7.0 General Qualification Criteria:
In addition to the General BRC/BEC, following criteria on Bidders' Experience and their financial
capabilities shall be considered (documentary evidence to be provided along with the bid in Technical
RFx -> External Area - > Tender Documents) as on the Bid Closing Date:
i). Successful execution of a single order of value not less than Rs. 65.90 Lakhs for supply of similar
items during last 3 years .
Page 4 of 23
of Tender SGI7516P16 dated 15.06.2015
ii). Annual turnover of the firm in any of the last 3 financial years or current financial year should
not be less than Rs. 219.67 Lakhs.
8.0 Application showing full address/email address with Tender Fee (Non-refundable) of
Rs. 1,000.00 in favour of M/s Oil India Limited and payable at Guwahati is to be sent to Chief Material
Manager , Oil India Limited (Pipeline Headquarter ), P.O. Udayan Vihar, Guwahati -781171. Application
shall be accepted only upto one week prior to Bid Closing date. The envelope containing the application
for participation should clearly indicate “REQUEST FOR ISSUE OF USER ID AND PASSWORD FOR
E TENDER NO …” for easy identification and timely issue of user ID and password. On receipt of
requisite tender fee, USER ID and initial PASSWORD will be communicated to the bidder (through email) and will be allowed to participate in the tender through OIL’s e- Procurement portal. No physical
tender documents will be provided. Details of bidding document can be viewed using “Guest Login”
provided in the e-Procurement portal. The link to e-Procurement portal has been also provided through
OIL’s web site www.oil-india.com.
NOTE: PSUs and SSI units are provided bidding documents Free of Cost (as per govt guidelines),
however they have to apply to OIL's designated office to issue the tender documents before the last date
of sale of bidding document mentioned in the tender.
If the MSE is owned by SC/ST Entrepreneurs, the bidder shall furnish appropriate documentary evidence
in this regard. The documents submitted by the bidder shall be duly certified by the Statutory Auditor of
the bidder or a practicing Chartered Accountant (not being an employee or a Director or not having any
interest in the bidder’s company/firm) where audited accounts are not mandatory as per law.
9.0 Please note that all tender forms and supporting documents are to be submitted through
OIL’s e-Procurement site only except following documents which are to be submitted manually in sealed
envelope super scribed with Tender no. and Due date to Chief Material Manager , Oil India Limited
(Pipeline Headquarter ), P.O. Udayan Vihar, Guwahati -781171 on or before the Bid Closing Date
and Time mentioned in the Tender.
a) Original Bid Security (if not paid online)
b) Detailed Catalogue (if any)
c) Any other document required to be submitted in original as per tender requirement
All documents submitted in physical form should be signed on all pages by the authorised signatory of the
bidder and to be submitted in triplicate.
9.1 Tender Fee and Bid Security can also be paid through payment gateway in the e-tender portal.Please
refer to Vendor User Manual updated in the e-tender portal as well for further details.
10.0
Bidders are requested to examine all instructions, forms, terms and specifications in the
bid.Failure to furnish all information required as per the bidding document or submission of offers not
substantially responsive to the bidding document in every respect will be at the bidders risk and may
result in rejection of its offer without seeking any clarifications.
11.0
Bidders must ensure that their bid is uploaded in the system before the Bid closing date
and time. Also, they must ensure that above documents which are to be submitted in a sealed envelope are
also submitted at the above mentioned address before the bid closing date and time failing which the offer
shall be rejected.
12.0
Bid must be submitted electronically only through OIL’s e-procurement portal. Bid
submitted in any other form will be rejected. All the Bids must be Digitally Signed using “Class 3” digital
certificate (e-commerce application) as per Indian IT Act obtained from the licensed Certifying
Authorities operating under the Root Certifying Authority of India (RCAI), Controller of Certifying
Authorities (CCA) of India. The bid signed using other than “Class 3” digital certificate, will be rejected.
13.0
Any sum of money due and payable to the contractor (including Security Deposit
refundable to them) under this or any other contract may be appropriated by Oil India Limited and set-off
against any claim of Oil India Limited (or such other person or persons contracting through Oil India
Page 5 of 23
of Tender SGI7516P16 dated 15.06.2015
Limited) for payment of sum of money arising out of this contract or under any other contract made by
the contractor with Oil India Limited (or such other person or persons contracting through Oil India
Limited).
14.0
In the event of receipt of only a single offer against the tender within B.C. date, OIL
reserves the right to extend the B.C. date as deemed fit by the Company. During the extended period, the
bidders who have already submitted the bids on or before the original B.C. date, shall not be permitted to
revise their quotation.
15.0 Integrity Pact:
(a) OIL shall be entering into an Integrity Pact with the bidders as per format enclosed vide Annexure
DDD of the tender document. This Integrity Pact proforma has been duly signed digitally by OIL’s
competent signatory. The proforma has to be returned by the bidder (along with the technical bid) duly
signed (digitally) by the same signatory who signed the bid, i.e., who is duly authorized to sign the bid.
Any bid not accompanied by Integrity Pact Proforma duly signed (digitally) by the bidder shall be
rejected straightway. Uploading the Integrity Pact with digital signature will be construed that all pages of
the Integrity Pact has been signed by the bidder’s authorized signatory who sign the Bid.
b) The name of the OIL’s Independent External Monitors at present are as under:
SHRI RAGHAW SHARAN PANDEY, IAS (Retd.),
Former Secretary, MOP & NG,
e-Mail ID : rspandey_99@yahoo.com
SHRI RAJIV MATHUR, IPS (Retd.)
Former Director, IB, Govt. of India,
e-Mail ID : rajivmathur23@gmail.com
16.0 No press advt. will be published regarding amendment to Bidding Document or extension of BC
Date. The same will be uploaded in OIL website and informed to all prospective bidders who have been
allowed to participate against the particular e-tender.
Yours Faithfully
Sd(P.THAKURIA)
DEPUTY MANAGER MATERIALS (PL)
FOR CHIEF MANAGER MATERIALS (PL)
FOR : GENERAL MANAGER (PLS)
Page 6 of 23
of Tender SGI7516P16 dated 15.06.2015
ANNEXURE AAA
Tender No. SGI 7516 P16 dated 15.06.2015
Item srl
no
10
Quantity
Item Description:
15
CPCB approved 25 KVA Diesel Generator (DG) Set with acoustic enclosure
Scope:
1) Manufacture, Assembly, pre-dispatch Inspection & Testing & Supply of DG sets
with acoustic enclosure as per technical specifications mentioned below
2) Supply of Air Intake & Exhaust Ducting, Exhaust Silencer Piping
3) Supply of all accessories for Fuel supply & return from existing piping from Diesel
tank
4) Supply of all electrical cables & earthing connectors from the DG set
5) Supply of Commissioning spares & two (2) years OEM recommended spares for
each DG set
6) Submission of Documents, Manuals & other records
7) Delivery of one set at each Repeater Station (as per attached Station list)
8) Safe Unloading & storage till installation
General Conformity with Statutory Acts, Rules, Standard & Codes:
1) All components shall conform to relevant Indian Standard Specifications, wherever
existing, amended to date. Otherwise, International standards such as ISO, BS, IEC, IP
etc. shall be complied, as applicable.
2) OISD standard shall be followed for guidelines on safety, wherever applicable.
3) All electrical works shall be carried out in accordance with the provisions of Indian
Electricity Act 2003 and Indian Electricity Rules 1956 as amended up to date.
4) Central Pollution Control Board (CPCB), India rules & norms for Noise Limits,
Emission levels & other parameters, as applicable.
(a) TECHNICAL SPECIFICATION - RECIPROCATING INTERNAL
COMBUSTION ENGINE:
Diesel Engine, Air cooled, 3 cylinder, vertical inline, 4 Stroke, Compression Ignition,
capable of developing net minimum 32 BHP at 1500 RPM. Performance rating as per
IS 10000:1980 as amended to date. The engine shall be of standard design of the
original manufacturer and suitable for operation in following site condition Maximum/ Minimum Temperature : 48/ 05 DEG C;
Maximum Humidity at 21 DEG C : 100 %, at 35 DEG C : 95 %, at 41 DEG C : 70 %
The engine shall conform to ISO : 3046 specifications and shall be rated for continuous
power with an over load power rating of 110% of the continuous power corresponding
to engine application for a period of 1 hr within a period of 12 hrs operation.
Performance rating as per IS 10002: 1981 as amended to date and maximum fuel
consumption as follows:
Specific Fuel Consumption (SFC) for direct injection engine is 252 g/ Kwh and for
indirect injection engine is 277 g/ Kwh.
Each engine to be completed with following accessories:1. Self Starter: 12 Volt Electric Starting system with starter motor and other accessories
including battery and battery leads. Both the positive and negative terminals of the 12
volts self starter for starting the engine should be insulated from its body.
2. Battery Charger: The battery charger is to be a solid-state device with adjustable
float voltage control. It is to be a constant voltage device with current limit, and it is to
include an equalize switch which will allow the battery to be overcharged for
maintenance purpose. Alternatively, with battery charging alternator unit and voltage
regulator suitable for starting batteries.
3. Lube Oil Systems: A special lube oil system to sustain preferably longer continuous
unmanned operations with wider sump design or with additional Lube Oil tank. The
lubricating system should comprise of lubricating oil pump, lubricating oil filter with a
replaceable paper element, lubricating oil cooler, lubricating oil pan and crankcase
breather. The lubricating oil pump shall be a positive displacement type that is integral
Page 7 of 23
of Tender SGI7516P16 dated 15.06.2015
UOM
Nos.
with the engine.
4. Heavy duty Lubricating Oil Filter with provision for water separation
5. Lube Oil Pressure Switch.
6. Lube Oil pressure Gauge or Digital Display in Engine Integrated control panel
7. Lube Oil Temperature switch
8. Lube Oil Temperature Gauge or Digital Display in Engine Integrated control panel
9. Exhaust Temperature Gauge.
10. Engine Tachometer (or may be included in the control panel)
11. 12 Volts stop solenoid energized to run with auto disconnection of starting cell.
Operation voltage of cut-off solenoid shall be 12 volts DC.
12. Heavy duty Dry type Air cleaner with a vacuum indicator with dry element
requiring replacement no more frequently than 500 hours
13. Engine should be supplied without its diesel tank, as in OIL Repeater Station there
is a Separate Diesel tank of capacity 12 KL to feed the engine (along with return piping
for Leak-off fuel)
14. Protection devices for:
a) Low Lube Oil Pressure & High Lube Oil Temperature shut down: One no. Low lube
oil pressure (LLOP) switch and one no Lube oil temperature (LOT) switch to be
incorporated with the engine for protection of low lube oil pressure and high lube oil
temperature respectively. These both switches are comprising with one normally
opened and one normally closed contact (1 NO + 1 NC). The operating range for the
LLOP switch should be 1.5 ± 0.15 Kg/cm2 & LOT should be 125 ºC± 30ºC as per
norm.
b) High Cylinder Head Temperature shut down: One no. High Cylinder Temperature
(HCT) switch to be provided with the engine, which consists of one normally closed
contact (NC) for protection of engine cylinder head from excessive temperature. The
operating range of temperature switch should be within 170 ºC to 200ºC
c) Over Speed Shut-down.
d) V-Belt Failure Shut-down: One no V-belt switch comprising with 1 normally
opened & one normally closed contact for monitoring of cooling system & to
incorporate safety shut down.
15. Fuel system: It shall be fed through engine driven fuel pump. Replaceable element
Fuel Filter (preferably twin fuel filter arrangement) shall be suitably located to permit
easy servicing. Fuel inlet line to the engine shall be having stainless steel flexible
connection to take care of vibration/shock, if any, in the system. Any piping
modification, new valve & hose required shall be in the scope of the supplier. All such
materials shall be of good quality and suitable for use in Oil & Gas Industry.
16. Governor: The engine speed governing system shall be of inbuilt type with the
engine with Governor (Preferably WOODWARD make) and related linkages. The
engine governor shall be Mechanical / Mechanical-Hydraulic / Electronic Speed
Control with EG Electro-Hydraulic actuator or Barber Coleman Equal. Speed drop
shall be extremely adjustable from 0 (isochronous) to 10% from no load to full rated
load. Steady state frequency regulation shall be + / - 0.5 percent. The engine governing
should be in accordance with Class G2 Governing specified in ISO 8528-1 : 2005 /
Governing Class A2 as per IS:10000-7 (latest version).
17. Absorption type exhaust silencer with exhaust pipe and stainless steel bellow.
18. Hot Air Outlet Ducting: A proper customized arrangement of duct is to be made for
discharging accumulated hot air within the canopy to open atmosphere outside the
engine room. Ducting shall be made from MS sheet of minimum 1.5 mm thickness
with good workmanship & finishing.
19. Cold Air Inlet Ducting: A proper customized arrangement of duct for fresh air
suction is to be made using the existing air route of engines at the Repeater Station.
Ducting shall be made from MS sheet of minimum 1.5 mm thickness with good
workmanship & finishing.
20. Exhaust System: Dry exhaust manifold & heavy duty exhaust pipe to take hot
engine exhaust outside the engine room. Suitable residential grade silencer
arrangement to reduce noise level is to be incorporated. Exhaust Piping should be
installed with appropriate insulation and shielding and to be supported and braced to
prevent weight or thermal growth being transferred to the engine and flexible
expansion fittings provided to accommodate thermal growth. Exhaust stack height
above building height shall conform to required norms.
21. Fan and Belt guarding: The fan, fan drive, and fan belts shall be covered with
guarding for personnel protection. Non-sparking guards over belt drives and couplings
Page 8 of 23
of Tender SGI7516P16 dated 15.06.2015
has become mandatory as per recommendation of OISD (Oil Industry Safety Director)
(OISD-STD-127)
22. Dynamically balanced flywheel with gourd.
23. Necessary flexible coupling and non-sparking gourd for alternator and engine
(applicable only for double bearing alternator).
24. The bidder shall submit the technical data sheet & catalogue of the engine along
with relevant performance rating Curves and following specific data:
i) Gross HP developed at rated RPM
ii) Net HP developed at rated RPM
iii) Maximum fuel consumption in Ltr/Hr- at 100 % , 75 % & at 50 % Load.
(b) TECHNICAL SPECIFICATION - ALTERNATOR:
1. Capacity : 25 KVA brushless
2. Voltage : 400/415 V, 50Hz
3. Phase: 3(Three) Phase.
4. Power Factor: 0.8
5. RPM : 1500
6. Class of Insulation : Class F/H
7. Duty: SI Conforming to IS4722-1968 or IS 13364/4722
8. Amb. Temperature: 40 Degree Centrigrade
9. Phase Sequence : IS 13364 /4722 (UVW-CW)
10. REGULATION: The Alternator should have voltage and frequency regulation
within ± 2.5% from No load to Full load with a maximum recovery time not more than
3 (three) seconds. The Alternator should build up full voltage instantaneously as soon
as the engine attains full RPM (i.e. 1500 RPM)
11. TERMINAL BOX: The terminal box of the Alternator should be suitable for
connecting 4 x 25 Sq.mm multi stranded PVCA aluminium cable with a detachable
cable entry plate. The terminal block should be made of non hygroscopic materials
with good insulating properties and strong enough to withstand the cable load and the
temperature generated inside the Generator's control room.
12. HOUSING AND MOUNTING: The Alternator should be directly coupled with
the prime mover (above engine) and both shall be mounted on a common fabricated
channel base frame complete with anti vibration mountings.
(c) TECHNICAL SPECIFICATION - ACOUSTIC ENCLOSURE:
The generating set comprising of engine coupled with alternator for each set should be
placed inside an acoustic enclosure having the following salient features:
i) The acoustic enclosure should be of modular construction with the provision to
assemble and disassemble easily at site. There should also be adequate provision of
taking out the equipment for maintenance / repairing jobs and reinstalling the same
after necessary corrective action.
ii) The engine generator shall be factory enclosed in not less than a 12 gauge cold
rolled steel enclosure constructed with corner posts, uprights and headers. The weatherproof and corrosion resistant acoustic enclosure should be duly surface treated,
phosphated and finally powder coated for long lasting finish. The sheet metal
components should preferably be hot dip, pre-treated before powder coating with
special pure polyester based powder.
iii) The sound proofing of the enclosure should be done with self extinguishing high
quality rock wool / mineral wool conforming to IS 8183. The rock wool should be
further covered with fiber glass tissue and perforated sheet.
iv) The silencer must be such that sound level is permitted maximum of 75 dbA at 1
meter from the enclosure surface. Exhaust silencer shall be provided of the size as
recommended by the manufacturer and shall attenuate the sound to the level noted
above. It shall be supplied with a flexible, seamless, stainless steel exhaust connection
as well as with all internal pipe work. These components must be properly sized to
assure operation with minimum back pressure and high sound when installed.
v) The canopy should be finished in synthetic enamel paint incorporating rust
inhibitors and Aluminium sprayed silencers and spark arrestors to guarantee a superior
and long lasting finish.
vi) There should be carefully designed inlet and outlet baffles / attenuators with
corresponding weather conditions allowing sufficient air flow, for the set to operate
even under the harshest ambient conditions whilst maintaining specified noise levels.
Suitably sized blower should be incorporated to meet total air requirement and
temperature within the enclosure and Generator house to be maintained.
Page 9 of 23
of Tender SGI7516P16 dated 15.06.2015
vii) The temperature inside the enclosure should be suitable for human comfort. There
should be a provision of emergency shutdown of the generating set (Prime Mover)
from outside the enclosure in addition to the control panel fitted outside the Canopy.
viii) The enclosure should be complete with power and control wiring between control
panel installed outside the Genset Enclosure and Alternator and other components like
blowers etc with proper size copper cable. The cables should be terminated using gland
and tinned copper sweating sockets and run through guard pipe. The enclosure should
have the sufficient space in and around the generating set to facilitate maintenance and
operation of the set.
ix) The control panel for the Generating set should be installed separately at existing
location of control panel in the Repeater Station. A drawing is attached herewith the
position of the Engine , its Control Panel , Size of the Engine with acoustic enclosure
and position of Separate control panel , its allowable dimensions etc.
x) The connection from the alternator and control panel should be carried out with 3.5
core 120 sq. mm PVC insulated, PVC sheathed armoured copper cable and cable
should be terminated with proper size of tinned copper sweating socket and cable
glands at alternator and panel end. All the terminal boxes/Junction boxes etc, the
battery and self starter connection terminals / and its components should be housed
inside intrinsically safe enclosure.
xi) ENCLOSURE ILLUMINATION: A separate circuit shall be provided for lighting
of the acoustic part of the enclosure. Armoured cable and FLP cable glands should be
used for wiring purpose inside the acoustic Make of Luminaire : Baliga / FCG /
SUDHIR
xii) Enclosure design should be such that for any major maintenance activities the
enclosures from any side can be easily dismantled and re-erected.
xiii) Generating set comprising of Engine, Alternator and other auxiliaries should be
placed inside an acoustic enclosure (approved by ARAI, Pune/ NPL, New Delhi/
NSTL, Visakapatnam/ FCRI, Palghat / NAL, Bangalore) and the unit should be
mounted to a common base frame. The set should have proper arrangement for easy
loading /unloading to facilitate ease in transportation.
xiv) A panel viewing window should be provided to facilitate visual monitoring of the
equipment from outside.
xv) SKID : The skid should be fabricated from sufficiently strong steel section for
carrying the generating set from one place to another from time to time.
xvi) NOTE: Bidders should submit layout drawing of the acoustic enclosure indicating
positions of engine, alternator, and control panel etc along with the wiring diagram of
the package and will have to be approved by OIL before execution of the order.
(d) GENERAL NOTES:
a. The offer will not be acceptable if the party do not quote for all items of the tender
and supply, installation, commissioning of all items and cables.
b. In their offer the bidder must mention their detailed comments point-wise against
each point of tender specifications. Any deviation from the tender specification shall be
specifically mentioned. Specific type and make of equipment should be mentioned. All
the information required as per tender specifications must be submitted.
c. In the event of an order the bidder will submit to OIL within one month of placement
of order all documents and drawings as required against each item.
d. The manufacture of the equipment is to be started only after written approval of the
required drawings/ documents by OIL as mentioned in tender against all equipments.
e. Bidder will provide with the offer the list of tools and equipment available with the
bidder to carryout the installation and commissioning work as per tender.
f. The bidder will be responsible for safety of its personnel and safety of all the
equipment. All the safety gadgets required for safely carrying out the job shall be
provided by the bidder.
g. Bidder will be responsible for safe custody of all the items before handing over to
OIL.
h. Handing over to OIL means supply, installation and commissioning of all items as
per order and submission of all the documents and drawings as per order.
i. The bidder to strictly ensure that all the cut ends of cables, packing materials,
leftover items are removed from site after completion of work.
j. No environmental damage shall be done while carrying out the job.
k. All the test reports must be signed by licensed electricians, jointers and supervisors
who have carried out the installation and commissioning work as per order.
Page 10 of 23
of Tender SGI7516P16 dated 15.06.2015
(e) PARTS LIST, INSTRUCTION MANUAL & DRAWING:
A. The supplier should provide two sets each of the manuals and books listed below for
each unit:
1. OPERATING INSTRUCTIONS- with description and illustration of all switchgear
controls and indicators and engine and generator controls.
2. PARTS BOOKS-that illustrate and list all assemblies, subassemblies and
components, except standard fastening hardware (nuts, bolt, washers etc.).
3. PREVENTIVE MAINTENANCE INSTRUCTIONS- on the complete system that
cover daily, weekly, monthly, biannual, and annual maintenance requirements and
include a complete lubrication chart.
4. ROUTINE TEST PROCEDURES-for all electronic and electrical circuits and for
the main AC generator.
5. TROUBLESHOOTING CHART- covering the complete generator set showing
description of trouble, probable cause and suggested remedy.
6. RECOMMENDED SPARE PARTS LIST- showing all consumables anticipated to
be required during routine maintenance and test.
7. WIRING DIAGRAM AND SCHEMATICS- showing function of all electrical
components.
8. One set of drawing showing installation details of the generating set, type of skid,
wiring diagram for the control panel & Distribution Feeder Panel( inclusive of float
charger ) and wiring drawing between the alternator and control & Distribution Feeder
Panel.
All control & Distribution Feeder panel diagram and schematic diagram are to be sent
to us before supply of order materials.
B. All manuals and books described above shall be contained in rigid plastic pouches
and in digital form along with the Genset.
(f) SPARES AND SERVICE:
(i) Necessary Commissioning spares & two (2) years OEM recommended spares for
each DG set shall be supplied with the order.
(ii) The bidder shall submit written assurance along with the offer in regards to service
and availability of all spares for next 10 (Ten) years from the commissioning of the
Unit.
(iii) The bidder shall submit pricelist of Commissioning Spares and 2 years
Recommended/ Critical Spares. This is for reference only and shall NOT be considered
for bid evaluation.
(g) DRAWINGS AND MANUALS:
i) Technical literature / catalogue and electrical circuit diagram to be enclosed with the
quotation/offer for our necessary scrutiny, otherwise offer shall be rejected.
ii) Test certificates to be provided with each Generator Set and these tests to be carried
out as per IS specification.
iii) Instruction manual, Technical literature and electrical circuit diagram along with
each Gen. Set are to be supplied.
(h) INSPECTION & TESTING:
i) Pre dispatch inspection of the sets shall be carried out by the supplier at the works of
manufacture. Load testing of the generator sets for output and performance shall be
carried out in presence of the purchaser or his representative appointed for the purpose
and to his satisfaction.
ii) Inspection and Testing of the Alternator sets (Completed unit of Engine &
Alternator with its acoustic enclosure) will be witnessed by OIL engineers /
representatives at the Supplier's premises prior to despatch.
iii) Intimation for Inspection & Testing shall be sent to M/s OIL INDIA LIMITED by
the Supplier at least fifteen days (15 days) in advance in both the cases
iv) Pre Despatch Inspection & Testing arrangement at manufacturing unit of Generator
Set will be arranged by the Supplier at Supplier's cost including consumables. Supplier
have to arrange at least 3 (One day /per visit at manufacturing unit excluding to & fro
journey period) visits for 2 nos. of Representatives from OIL for 15 nos. Gen Sets .
(i) WARRANTY:
The DG set comprising of Engine & Alternator shall be warranted against defective
material/ faulty workmanship/ faulty operation for a period of minimum 12 months
from the date of commissioning or 3000 operating hours, whichever occurs first.
Page 11 of 23
of Tender SGI7516P16 dated 15.06.2015
(j) STATUTORY CONFORMANCE:
i) The offered Generating Sets shall comply with the latest CPCB norms/regulations.
ii) In the event of any new CPCB norms/regulations governing Diesel Engine driven
Generating Set are made effective prior to delivery of the Gen Set (but after bid closing
date) the supplied Gen Set shall comply with the latest CPCB norms/ regulations.
The compliance report from Govt. approved agencies must be submitted prior to
dispatch of the Gen Set for OIL's scrutiny and acceptance.
Note:
Engine Data Sheet, Alternator Data Sheet are enclosed herewith.
20
Design, Manufacture/Assemble, Installation and Commissioning of Auto Generator
Control Panel as replacement of existing 25 KVA DG Sets at Repeater Stations of
OIL in Assam, West Bengal & Bihar.
15
Nos.
15
Nos.
The supplier shall supply mandatory & critical spares for panels for at least two years
after warranty along with the panel.
Auto Generator Control Panel:
1. Operation philosophy of the supplied panels shall be same or equivalent as existing
ones. Bidder shall study our existing system carefully during bidding & execution.
2. The panels shall have Multifunctional relay or group of relays and accessories to
accomplish at least the following features:
(a). Auto/Manual start/off of the set.
(b).Fault Detection & initiation of shut down during operation for crank/start failure ,
High Engine Temperature Fault, High lub-oil temperature Fault, Low lub oil pressure
Fault, voltage out of band and frequency out of band faults. Alarm indications and
events logging systems shall be part of the design.
3. In-built Battery Charger with Auto/Manual Boost/Float charging feature should be
incorporated to the charge the DG Set Battery. Output D.C voltage and current
indicating instruments are to be provided.
4. The panels shall be fitted with Analog Voltmeter & Ammeter with selector switches,
Built-in Transducer type Analog Power Meter & Power Factor Meter, Running Hour
Meter, Electronic LED Frequency Meter, Electronic Static watt-hour Meter with LED
Display and other operating & alarm/fault indicating display.
5. Suitable 4 pole MCCB with Adjustable Thermal-Magnet Release along with SwitchDisconnector Fuses of suitable rating & type shall be provided in the panel as incomer
for the Power Cable . The outgoing power from the GCP shall be routed to
Distribution Panel Bus Bar through Suitable Power Contactor to facilitate Auto/Manual
changeover as in Diagram-2. Electrical & mechanical interlocking as shown in the
schematic shall be provided along with suitable Switch Fuse Unit incomers(3 numbers
) in DB Panel. Power cable shall be of suitable size PVC armoured type with ISI mark
& 1100 volt grade.
6. All the control & power interconnection wirings shall be done with copper flexible
PVC wires ( ISI Marked & 1100 volt grade) with accepted colour codes.
7. The panel board must be built by M.S Sheet of suitable gauge, floor mounted type,
IP-44 ,with load bearing member, doors, partitions, covers, equipment mounting plate
& removable gland plate, painted with texture finish electro-static paint ( Powder
Coating) with paint thickness 80(+)(-)20 microns.
8. The panels shall be earthed as per standard practice. All doors shall have earthing
with main frame through copper braided wires.
9. The test certificate as per IS-8623 Part-1, 1993 & IS 13947(Part-1), 1993 for the
individual panel shall be submitted with the panel along with test certificates of
individual components of panel as applicable.
30
Design, Manufacture/Assemble, Installation and Commissioning of
Distribution Panel:
1. Design, manufacture, supply, installation & commissioning of Distribution Panels as
replacement of existing ones shall be in the bidder scope. All control & interconnecting
Page 12 of 23
of Tender SGI7516P16 dated 15.06.2015
cables shall be flexible PVC copper wire with ISI mark & 1100V grade.
2. The panel board should house the following:
(a). Electrical & mechanical interlocked TPN Power Contactors as shown in the
Diagram-2.
(b). TPN Copper Bus Bars of suitable size & mountings with connections & spare 3
blank holes in each bus.
©. Three 63 Amp TPN Switch Disconnector Fuse units as Incomers for DB Panel
Board..
(d). 32 Amp TPN MCB- 4 nos. – outgoing.
(e). 10 Amp TPN MCB- 6 nos. – outgoing.
(f). 4 Amp TPN MCB - 4 nos. – outgoing.
(g). Four nos.Empty partitions dimension not less than 30cmx20cm with door and
Two LED indication lamp in each partition ( colour Red & green) and blank power &
control terminal block inside .
(h). LED Phase Indication – 3 nos.
i)One smart Meter to be provided to facilitate recording Total KWH consumption &
reading bus voltage,current,power etc.
3. Construction, testing etc. and earthing shall be same as Generator Control Panels.
40
Note: Please refer schematic drawing II- attached herewith
INSTALLATION , COMMISSIONING, TESTING AND HANDING OVER:
Installation and Commissioning of the Generating set, Control panels & Distribution
Feeder Panels shall be carried out by the supplier in the presence of OIL
representatives at its Repeater Stations located in three different states of Assam,
Bengal & Bihar. Services of qualified and competent personnel from equipment
manufacturer are essential during installation and commissioning of the generating
sets.
1
Persons engaged for installation, testing and commissioning of alternator, control panel
& Distribution Panels should have valid electrical license issued by State Licensing
Board. A person who is authorized for supervision of all electrical works should have
valid supervisory license.
Installation, Testing & commissioning includes site preparation and modification of the
whole system comprising 15 (fifteen) units of Gen Sets with its control panels and
15(fifteen) nos. of Distribution feeder panel with auto changeover & manual
changeover facility in 15 nos. of Repeater Stations located in different locations as per
attached list herewith.
One (1) unit of Gen set out of existing 3 units with its Control Panel & One no.
Distribution feeder Panel has to be dismantled before installation & commissioning of
new set and a Temporary control panel has to be placed for un-interrupted power
supply during commissioning period. All related materials, cables, consumables &
dismantling of old sets and corresponding control & distribution panel are the scope of
Supplier.
OIL will provide necessary statutory permits for welding and cutting jobs in classified
areas as and when required. Installation/ commissioning charges should be quoted
separately which shall be considered for evaluation of the offers. These charges shall
include amongst others to and fro fares, boarding/ lodging and other expenses of the
commissioning engineers during their stay at Designated Repeater Stations. All
Personal, Income and Service Tax etc. towards the services provided by the supplier
shall be borne by the supplier and will be deducted at source. Bidders should also
confirm about installation/ commissioning in the Technical Bid.
Notes:
a) Once commissioned at designated site the generating set will be subjected to a trial
run (reliability run) on available load for a minimum period of 48 hrs continuously and
on satisfactory performance shall be subsequently handed over to OIL.
b) OIL will give 14 days advance notice prior to installation to the successful bidder.
General Notes for Bidder:
Page 13 of 23
of Tender SGI7516P16 dated 15.06.2015
AU
(Bidders should confirm each & every point clearly. Deviations, if any, should be
highlighted in the quotation).
1.0 Materials shall be brand new, unused & of prime quality.
2.0 Installation & Commissioning: The successful bidder will be required to install
and commission the unit by their competent service engineer.
3.0 Installation/ Commissioning charges must be quoted separately on lump sum basis
which shall be considered for evaluation of the offers. Total Nos. of days required for
commissioning shall also be clearly indicated by the bidders.
4.0 While quoting Installation/Commissioning above, bidder should take into account
all charges including to and fro fares, boarding/lodging, local transport at Respective
Repeater Stations in Assam Bengal & Bihar and other expenses of supplier's
personnel during their stay at Respective Locations.
Special Terms & Conditions :
Successful bidder shall have to carry out Supply, Safe Unloading, Installation, Testing, commissioning including
site preparation and modification of the whole system comprising Fifteen(15) nos. Gen Sets, its
Control panel and fifteen(15) no. Distribution feeder panel with auto changeover & manual changeover facility
.Supply of all related materials, cables, consumables and jobs at designated Repeater Station of OIL INDIA
LIMITED and dismantling of existing 1 no out of 3 nos Gen sets with its control and distribution panel in one
Repeater Station.
A temporary distribution panel has to be installed during commissioning period for un interrupted power supply
during commissioning period.
Generator Set :
1) Supply of 15 Nos of 25 KVA Capacity Gen Set with its 15 Nos Control Panel – ( 1 No Gen Set with its control
panel in one Repeater Station and so 15 nos requires in 15 Nos Repeater Station) including transportation and
unloading at site .
2 .Distribution Feeder Panel: 15 Nos.( One no Distribution Feeder Panel In One Repeater Station and 15 Nos
required in 15 Repeater Stations), including transpiration and unloading at site.
4. Installation, Testing & Commissioning including site preparation and modification of the whole system at
different Repeater Stations of Oil India Limited.(Postal address of each Repeater Station enclosed ) Dismantling of
existing 1 no Gen set with corresponding control and Distribution Feeder Panel in each Repeater Station and
removing the Old Sets , Panel and placing it outside the Repeater Station with GI Sheet.
The sole supplier should divide the work in three groups for installation , commissioning & testing of the Gen Sets
with its panels. The Three Group Should work simultaneously in three different locations , so that the duration of
installation & commissioning period can be minimized.
RESPONSIBILITY: The responsibility for performance to the specifications shall not be divided among individual
component manufacturers, but must be assumed solely by the primary manufacturer. This includes generating
system design, manufacture, test, and having a local supplier responsible for service, parts and warranty for the total
system.
AFTER SALES SERVICE : Bidder should indicate the availability of nearest after sales service centre along with
the details of infra structural capabilities. The nature of after sales service, which can be provided by the supplier,
during initial erection and commissioning as also subsequent operation should be clearly stated in the quotation.
SERVICE AND WARRANTY:
(i) The manufacturer should have a local authorized dealer who can provide factory trained servicemen, the required
stock of replacement parts, technical assistance, and warranty administration.
(ii) The manufacturer’s authorized dealer shall have a parts and service facility within 300 km of the jobsite.
(iii) The generator set supplier shall have factory trained service representatives and tooling necessary to install and
commission all provided equipment.
The warranty period for the Gen set and ancillary equipment should be a minimum of 18 months from the date of
dispatch/ shipment or 12 months from the date of commissioning of the equipment whichever is earlier. Any defects
in the Engine or Alternator during warranty period shall be replaced by the supplier at his cost without any extra
charge to OIL.
Page 14 of 23
of Tender SGI7516P16 dated 15.06.2015
Data Sheet: Engine Data Sheet and Alternator Data Sheet Enclosed Herewih.
INSPECTION:
1. The Company shall as it may deem fit depute their Engineer/ Inspector to carryout factory inspection and test the
equipments when the panels are manufactured/ assembled before their dispatch, for confirmation of the technical
specifications by the bidder.
2. Before commencement of the second panel production job the contractor shall have to arrange at their own cost
for pre dispatch inspection of first panel by OIL Engineers/ Inspectors. After satisfactory operation / testing only
other panel shall have to be started. The Company also has the right to inspect raw materials, components,
accessories etc. including facility available with Contractor to carryout these jobs.
3. For all electronics components, the items should be tested at the temperature of 50ºC
4. Manufacturer’s certificates in triplicate to be submitted to OIL for all equipments/ instruments.
5. On completion of the work, tests are to be carried out before commissioning. All test certificates in triplicate
should be handed over to OIL.
ERECTION & COMMISSIONING:
1. The control panels to be erected side by side at Repeater Stations, located at different locations in three states of
Assam, Bihar & Bengal . Similarly feeder Distribution Panel is to be installed sidewise almost 3 mtrs away from
the control panel. All terminations of the cables should be done properly with suitable cable gland and lugs. All civil
works including supply of materials and labour in connection with all above work have to be carried out by the
supplier.
2. The supplier should use only indigenous materials/ components as per as possible for the Control panel. In case,
imported components are used , the same have to be specifically mentioned in the tender giving details and
addresses of their sources of origin.
3. Location of Repeater Stations as per attached list.
*******************
Page 15 of 23
of Tender SGI7516P16 dated 15.06.2015
LIST OF REPEATER STATION LOCATIONS
STATE OF ASSAM
Sl. Name of
No. Repeater Station
Name of
Village
PL KM
Mouza
Circle
District
1
2
3
4
RS1, Maduri
RS2, Badulipar
RS3, Kaziranga
RS4, Ghani
90
172
214
314
Saloguri
Rangamati
Kaziranga
Jagiyal
Amguri
Khumtai
Bokakhat
Roha
Sibsagar
Golaghat
Golaghat
Nowgaon
5
6
7
8
RS5, Jagiroad
RS8, Dharamtul
RS9, Barpeta Road
RS10, Pratapkhata
Sensowanamdongia
Chengnigaon
Gosanibargaon
Ghahigaon
Bhatikuri
Ghunushahabi
Panigaon
Jhakhalipar Town
Pratapkhata
362
468
513
604
Gova
Pokowa
Gobardhona
Kharijadolio
Mayang
Chamota
Barnagar
Dorma
Morigaon
Nalbari
Barpeta
Kokrajhar
STATE OF WEST BENGAL
Sl. Name of
No. Repeater Station
Name of
Village
PL KM
Mouza
Circle
District
1
2
3
4
Chepani
Binaguri
Odlabari
Balichuka Pachim
655.5
728.8
784.4
905.8
-
Alipurduar
Dhupguri
Matali
Goalpokhora
Jalpaiguri
Jalpaiguri
Jalpaiguri
Dinajpur
RS11, Chepani
RS12, Binaguri
RS13, Odlabari
RS14, Kisanganj
STATE OF BIHAR
Sl. Name of
No. Repeater Station
Name of
Village
PL KM
Mouza
Circle
District
1
2
3
Belgachi
Jamunia
Sonawari
958.3
1058.4
1111
-
Purnia
Bihpur
Khagaria
Purnia
Bhagalpur
Bhagalpur
RS15, Belgachi
RS16, Thanabipur
RS17, Khagaria
Page 16 of 23
of Tender SGI7516P16 dated 15.06.2015
ANNEXURE BBB
Bid Rejection Criteria (BRC) & Bid Evaluation Criteria (BEC)
1.0 BID REJECTION CRITERIA (BRC)
The bid shall conform generally to the specifications and terms and conditions given in this bidding document. Bids
shall be rejected in case the goods/materials offered do not conform to required parameters stipulated in the
technical specifications. Notwithstanding the general conformity of the bids to the stipulated specifications, the
following mandatory requirements will have to be particularly met by the Bidders without which the same will be
considered as non-responsive and rejected. All the documents related to BRC must be uploaded alongwith the
Technical Bid.
(A) TECHNICAL
1.0 Bidder’s Qualification :
1.1 Bidder shall be an Original Equipment Manufacturer (OEM) of (a) Complete Generating set or (b) Engine
OR
Bidder shall be a 100% Subsidiary or Sister concern of Original Equipment Manufacturer (OEM) of (a) Complete
Generating set or (b) Engine
OR
Bidder shall be an authorized dealer of the OEM of (a) Complete Generating set or (b) Engine
OR
Bidder shall be an OEM approved assembler of Generating set.
1.2 Engine and Alternator should be procured directly from OEM or OEM’s 100% subsidiary or OEM’s Sister
concern or OEM’s authorized dealer
Note: But whatever may be their status in para 1.1 & 1.2 above, Bidder will have to enclose documentary evidence
along with the offer failing which offer will be rejected.
2.0 Bidder's Experience:
2.1 Bidders should have the experience of successfully completing at least 3(Three) orders in the last 10(Ten) years
before the original bid closing date of this tender against supply & commissioning of DG Sets of capacity 15 KVA
or above in PSUs, Central Govt. or any other Public Limited Company of India. Documentary evidence in the form
of contracts/ purchase order and completion certificate from the user, must be provided along with the quotation
failing which offer will be rejected.
3.0 Performance Track Record & Spares Availability:
3.1 The offered Generating set should have proven track record for power generation applications in Central Govt.,
PSU or any other Public Limited Company of India and in this respect the bidder should provide performance
certificate from the end user for operation of minimum of one year before original bid closing date for minimum 3
(three) orders as mentioned in above clause no. 2.1.
3.2 The bidder should provide written confirmation from OEM that the spares will be available for the next 10 years.
4.0 Statutory Conformance:
4.1 The bidder must categorically confirm the following in their bid, failing which bid shall be rejected:
(a) The offered Generating Sets shall comply with the latest CPCB norms/regulations.
(b) In the event of any new CPCB norms/regulations governing Diesel Engine driven Generating Set are made
effective prior to delivery of the Gen Set (but after bid closing date) the supplied Gen Set shall comply with the
latest CPCB norms/ regulations.
5.0 Technical Conformance:
5.1 The Diesel Engine shall be Air Cooled, Compressor Ignition, capable of developing net minimum 32 BHP at
1500 RPM. Performance rating as per IS 10002:1981 as amended to date and maximum fuel consumption as
follows:
Specific Fuel Consumption (SFC) for direct injection engine is 252 g/Kwh and for indirect injection engine is 277
g/Kwh.
5.2 The Alternator must be brushless type.
5.3 The whole Set shall be provided with acoustic enclosure.
Page 17 of 23
of Tender SGI7516P16 dated 15.06.2015
Technical data sheet complying above data must be submitted, failing which bid shall be rejected.
6.0
6.1 Bidder must quote for all items in the tender, failing which bid shall be rejected.
6.2 Bidder must fulfill Warranty Clause given the item specification, failing which bid shall be rejected.
(B)
COMMERCIAL :
i) The Bidder shall furnish requisite Bid Security by way of a Bank Guarantee/Bank Draft in the manner and as
specified in Section ‘Bid Security’ which shall be furnished alongwith the ‘Techno-Commercial Bid’. Any bid not
accompanied by a proper bid security will be rejected.
ii) Bids are to be submitted in a single stage two bid system, i.e. Technical Bid (Unpriced) and Priced Bid
separately. Bids shall be rejected outright if the technical bids contain the prices.
iii) Validity of the bid shall be minimum 120 days from the Bid Closing Date, otherwise the bid shall be rejected.
iv) The prices offered will have to be firm through delivery and not subject to variation on any account. A bid
submitted with an adjustable price will be treated as non-responsive and rejected.
v) Bids received after the bid closing date and time will be rejected.
vi) All the Bids must be Digitally Signed using #Class 3# digital certificate (e-commerce application) as per Indian
IT Act obtained from the licensed Certifying Authorities operating under the Root Certifying Authority of India
(RCAI), Controller of Certifying Authorities (CCA) of India. The bid signed using other than #Class 3# digital
certificate, will be rejected.
vii) C folder is meant for Technical bid only. Therefore, No price should be given in C folder, otherwise the offer
will be rejected.
viii) The User ID & Password are not transferable. Bids submitted by parties to whom the User ID & Password was
not issued by the Company will be rejected.
ix)
Conditional offers will be rejected.
Bids received in any form or media other than through OIL’s e-Procurement portal will not be accepted.
x)
xi)
Bid documents uploaded in the e-Procurement Portal shall be typed/written and scanned clearly and contain
no inter lineation, erasures or overwriting except as necessary to correct errors made by bidder, in which case such
corrections must be initialed by the person(s) signing the bid. Any bid not meeting this requirement shall be rejected.
xii) Bidder must accept and comply with the following clauses as given in the Bidding document in toto, failing
which offer will be rejected:
a.
b.
c.
d.
e.
Performance Bank Guarantee clause
Force Majeure Clause
Tax Liabilities clause
Arbitration clause
Liquidated damage clause
xiii). Integrity Pact:
OIL shall be entering into an Integrity Pact with the bidders as per format enclosed vide Annexure DDD of the
tender document. This Integrity Pact proforma has been duly signed digitally by OIL’s competent signatory. The
proforma has to be returned by the bidder (along with the technical bid) duly signed (digitally) by the same signatory
who signed the bid, i.e., who is duly authorized to sign the bid. Any bid not accompanied by Integrity Pact Proforma
duly signed (digitally) by the bidder shall be rejected straightway. Uploading the Integrity Pact with digital signature
will be construed that all pages of the Integrity Pact has been signed by the bidder’s authorized signatory who sign
the Bid.
Page 18 of 23
of Tender SGI7516P16 dated 15.06.2015
C. GENERAL:
i) In case bidder takes exception to any clause of Bidding Document not covered under
BEC/BRC, then the Company has the discretion to load or reject the offer on account of such exception if the
bidder does not withdraw/modify the deviation when/as advised by the Company. The loading so done by the
Company will be final and binding on the Bidders. No deviation will however, be accepted in the clauses
covered under BRC.
ii) In case any of the clauses in the BRC contradict with other clauses of Bidding Document
elsewhere, then the clauses in the BRC will prevail.
iii) Any exceptions/deviations to the Bidding Document and applicable statutory duties and levies
must be spelt out by bidder in their ‘Technical’ bid only. Any additional information/terms/conditions furnished
in sealed ‘Price Bid’ will not be considered by OIL for evaluation/award of contract.
iv) The originals of such documents (furnished by bidder(s)) shall have to be produced by
bidder(s) to OIL as and when asked for.
2.0 BID EVALUATION CRITERIA (BEC):
i) The bids confirming to the technical specifications, term and conditions stipulated in the bidding documents and
considered to be responsive after subjecting to Bid Rejection Criteria will be considered for further evaluation as per
the Bid Evaluation Criteria.
ii) To evaluate the inter-se-ranking of the offers, Assam entry tax on purchase value will be loaded as per prevailing
Govt. of Assam guidelines as applicable on bid closing date. Bidders may check this with the appropriate authority
while submitting their offer.
iii) Price bids of only those bidders will be opened whose offers are found technically acceptable. The technically
acceptable bidders will be informed before opening of the “price bid”.
iv) Other terms and conditions of the enquiry shall be as per General Terms and Conditions vide MM/LOCAL/E01/2005 for E-Procurement LCB Tenders. However, if any of the Clauses of the Bid Rejection Criteria / Bid
Evaluation Criteria (BRC / BEC) contradict the Clauses of the Bidding document or MM/LOCAL/E-01/2005
elsewhere, those in the BRC / BEC shall prevail.
v) To ascertain the inter-se-ranking, the comparison of the responsive bids will be made as per price format given in
Appendix-I.
Page 19 of 23
of Tender SGI7516P16 dated 15.06.2015
Appendix-I
Bidders are required to submit the summary of the prices in their commercial bids as per bid format
(Summary), given below :
Priced Bid Format ( SUMMARY ):
Item
Srl
No
10
20
30
40
Item Description
Manufacture, Assembly, predespatch Inspection, testing &
Supply of Diesel Generator Set.
Design, Manufacture/Assemble of
Auto Generator Control Panel
Design, Manufacture, supply of
Distribution Panel
Installation & Commissioning
UOM Qty
Unit
Required Price
No.
15
No.
15
No.
15
AU
1
(A)
(B)
(C)
(D)
(E)
(F)
(G)
(H)
(I)
(J)
(K)
(L)
(M)
(N)
Total
Price
Total material value of Item no 10, 20 , 30
Packing and Forwarding Charges
Total Ex-works value ( A+B+C)
Excise Duty including Cess, (Please indicate applicable rate of Duty)
Total Ex-works value including Excise Duty & Cess (D+E)
Sales Tax, (Please indicate applicable rate of Tax)
Total FOR Despatching station value ( F+G)
Road Transportation charges to different locations (Lumpsum)
Insurance Charges
State Entry tax
Total FOR Destination value (G+H+I+J)
Pre-despatch inspection and testing Charges (Lumpsum)
Installation & Commissioning charges (Lumpsum)
Service tax on Commissioning charges, if any
(please indicate the percentage)
(O)
Total Value, (K+L+M+N) above
(P)
Total value in words :
(Q)
Gross Weight :
(R)
Gross Volume :
1.0Pre-despatch Inspection and testing charges, Commissioning charges must be quoted
separately (not to include in materials cost) on lumpsum basis which shall be considered
for
evaluation of the offers. These charges should include amongst others to and fro fares,
boarding/lodging, local transport and other expenses of supplier’s commissioning and
training
personnel during their stay at the site
2.0Bidders must categorically indicate the Pre-despatch Inspection and testing charges ,
Commissioning charges & Training charges in their offers and must confirm about
providing the same in their Technical bids. In case Pre-despatch Inspection and testing
charges, Commissioning charges are NIL/inclusive, bidder must categorically mention the
same in their offer.
3.0 Summary of the prices, as per the bid format (Summary) mentioned above, to be uploaded in “Priced Bid” separately.
*****
Page 20 of 23
of Tender SGI7516P16 dated 15.06.2015
Tender No.
SGI7516P16 dated 15.6.2015
Annexure
EEE
Matrix for Technical & Commercial
Evaluation
Note :- Only Grey coloured boxes are to be
filled by the bidder
Name of Bidder :
Compliance by Bidder
SL. NO.
1
BEC / TENDER REQUIREMENTS
Indicate 'Confirmed' /
'Not Confirmed' / Not
applicable
Bidder to confirm that they have not taken
any exception/deviations to the bidding
document .
2
Confirm that the product offered strictly
conform to the technical specifications.
3
Confirm that the Offer has been made with
Bid Security along with the offer ?
4
Confirm unconditional validity of the bid
for 120 days from the date of opening of
techno-commercial bid.
5
Confirm that the prices offered are firm.
Conditional offer will be liable for
rejection?
6
Confirm that all relevant fields in the online biding format been filled in by the
bidders for the items quoted by them.
7
8
9
10
Confirm that the price bid is in conformity
with OIL’s online bidding format ?
Confirm that the Bid comply with all the
terms & conditions ?
Confirm that the offers and all attached
documents are digitally signed using digital
signatures issued by an acceptable
Certifying Authority (CA) as per Indian IT
Act 2000.
CONFIRM THAT YOU SHALL SUBMIT
PERFORMANCE BANK GUARANTEE
AS PER bidding document IN THE
EVENT OF PLACEMENT OF ORDER
ON YOU
Page 21 of 23
of Tender SGI7516P16 dated 15.06.2015
Indicate
Corresponding
page ref. of bid
Annexure FFF
Bidders Response Sheet
Sl
No.
1
Description
Remarks
Name of Bidder
2
Place of Despatch (Ex- Works)
3
Whether Freight charges have been included in your quoted
prices
Whether Transit Insurance charges have been included in your
quoted prices
4
5
Make of quoted Product
6
Offered Validity of Bid from Bid Closing Date
7
Delivery Period in days/weeks/months from placement of
order
Complied to Standard Payment Terms of OIL or not.
(Please refer to clause 23.2 of LCB Doc Booklet)
Bid Security Submitted (if applicable)
Details of Bid Security Submitted to OIL (if applicable)
a) Bid Security Amount (In Rs):
b) Bid Security Valid upto:
c) Name and Full Address of Issuing Bank:
Confirm that the Bid Security submitted (In case of Bank
Guarantee) is in toto as per format provided in the bidding
document.
Bid Security if Not submitted, reasons thereof
8
9
10
11
12
13
14
15
16
Whether you shall submit Performance Security in the event of
placement of order on you.
Whether submitted documents in support of General
qualification criteria of bidding document.
If bidder is Small scale unit whether you have quoted your own
product.
If bidder is Small scale unit , whether you are owned by SC/ST
entrepreneur.
If Integrity Pact submitted
Page 22 of 23
of Tender SGI7516P16 dated 15.06.2015
ANNEXURE - GGG
(TO BE FILLED UP BY ALL THE VENDOR IN THEIR OWN LETER HEAD)
(ALL FIELDS ARE MANDATORY)
Tender No.
Name of Beneficiary
Vendor Code
:……………………………………………………………………
:M/s……………………………………………………………………
:………………………………………………………………………...
Address
:..……………………………………………………………………….
..………………………………………………………………………..
Phone No. (Land Line)
:..……………………………………………………………………….
Mobile No.
:..……………………………………………………………………….
E-mail address
:..……………………………………………………………………….
Bank Account No. (Minimum
Eleven Digit No.)
:..……………………………………………………………………….
Bank Name
:..……………………………………………………………………….
Branch
:..……………………………………………………………………….
Complete Address of your
:..……………………………………………………………………….
Bank
:..……………………………………………………………………….
IFSC Code of your Bank
a) RTGS
:………………………………………………………………………...
b) NEFT
:………………………………………………………………………...
PAN
:………………………………………………………………………...
VAT Registration No.
:………………………………………………………………………...
CST Registration No.
:………………………………………………………………………...
Service Tax Registration No.
:………………………………………………………………………...
Provident Fund Registration
:………………………………………………………………………...
I/We confirm and agree that all payments due to me/us from Oil India Limited can be remitted to
our above mentioned account directly and we shall not hold Oil India Limited responsible if the
amount due from Oil India Limited is remitted to wrong account due to incorrect details furnished
by us.
………………………………
Office Seal
Signature of Vendor
Counter Signed by Banker:
Seal of Bank:
Enclosure: Self attested photocopies of the following documents1)
2)
3)
4)
5)
6)
7)
PAN Card
VAT Registration Certificate
Service Tax Registration
CST Registration
Provident Registration Certificate
Cancelled cheque of the bank account mentioned above (in original).
Bank Statement not older than 15 days on the date of submission.
Page 23 of 23
of Tender SGI7516P16 dated 15.06.2015
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising