NANO-BT-i1 User Manual

NANO-BT-i1 User Manual
NANO-BT-i1 EPIC SBC
MODEL:
NANO-BT-i1 Series
EPIC SBC with 22nm Intel® Atom™ or Celeron® SoC,
Dual GbE, DDR3, HDMI, VGA, LVDS, USB 2.0/3.0, COM Ports
Two SATA 3Gb/s Ports, IPMI 2.0 and RoHS
User Manual
Page i
Rev. 1.02 – June 27, 2014
NANO-BT-i1 EPIC SBC
Revision
Date
Version
Changes
June 27, 2014
1.02
Updated supported memory specifications in Chapter 1.
May 7, 2014
1.01
Updated Section 1.6: Dimensions
Updated Chapter 6: Software Drivers
Updated Table 3-15: LVDS Connector Pinouts
April 3, 2014
Page ii
1.00
Initial release
NANO-BT-i1 EPIC SBC
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
Page iii
NANO-BT-i1 EPIC SBC
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 INTRODUCTION........................................................................................................... 2
1.2 MODEL VARIATIONS ................................................................................................... 3
1.3 BENEFITS ................................................................................................................... 3
1.4 FEATURES ................................................................................................................... 4
1.5 CONNECTORS ............................................................................................................. 5
1.6 DIMENSIONS ............................................................................................................... 7
1.7 DATA FLOW ................................................................................................................ 9
1.8 TECHNICAL SPECIFICATIONS .................................................................................... 10
2 PACKING LIST ........................................................................................................... 12
2.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 13
2.2 UNPACKING PRECAUTIONS ....................................................................................... 13
2.3 PACKING LIST........................................................................................................... 14
2.4 OPTIONAL ITEMS ...................................................................................................... 15
3 CONNECTORS ........................................................................................................... 16
3.1 PERIPHERAL INTERFACE CONNECTORS..................................................................... 17
3.1.1 NANO-BT-i1 Layout......................................................................................... 17
3.1.2 Peripheral Interface Connectors ..................................................................... 18
3.1.3 External Interface Panel Connectors............................................................... 20
3.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 20
3.2.1 +12 V Power Connector .................................................................................. 20
3.2.2 Audio Connector .............................................................................................. 21
3.2.3 Battery Connector............................................................................................ 22
3.2.4 Backlight Inverter Connector .......................................................................... 23
3.2.5 Buzzer Connector............................................................................................. 24
3.2.6 Chassis Intrusion Connector............................................................................ 25
3.2.7 Digital I/O Connector ...................................................................................... 25
3.2.8 Fan Connector (CPU)...................................................................................... 26
3.2.9 Fan Connector (System) .................................................................................. 27
Page iv
NANO-BT-i1 EPIC SBC
3.2.10 Front Panel Connector .................................................................................. 28
3.2.11 IPMI LED Connector ..................................................................................... 29
3.2.12 iRIS Module Slot ............................................................................................ 30
3.2.13 LAN LED Connectors .................................................................................... 31
3.2.14 LVDS Connector ............................................................................................ 32
3.2.15 Memory Card Slot .......................................................................................... 33
3.2.16 PCI-104 Connector........................................................................................ 34
3.2.17 PCIe Mini Card Slot ...................................................................................... 35
3.2.18 Power Button Connector................................................................................ 37
3.2.19 Power Button ................................................................................................. 38
3.2.20 Reset Button Connector ................................................................................. 38
3.2.21 SATA 3Gb/s Drive Connectors....................................................................... 39
3.2.22 SATA Power Connectors ................................................................................ 40
3.2.23 Serial Port Connectors, RS-232..................................................................... 41
3.2.24 Serial Port Connector, RS-422/485................................................................ 42
3.2.25 SMBus Connector .......................................................................................... 43
3.2.26 SPI Flash Connector...................................................................................... 44
3.2.27 SPI Flash Connector, EC ............................................................................... 45
3.2.28 USB 2.0 Connector ........................................................................................ 46
3.3 EXTERNAL PERIPHERAL INTERFACE CONNECTOR PANEL ......................................... 47
3.3.1 Ethernet Connectors ........................................................................................ 47
3.3.2 HDMI Connector ............................................................................................. 49
3.3.3 Keyboard/Mouse Connector ............................................................................ 50
3.3.4 USB 2.0 Connector .......................................................................................... 51
3.3.5 USB 3.0 Connector .......................................................................................... 51
3.3.6 VGA Connector ................................................................................................ 52
4 INSTALLATION ......................................................................................................... 53
4.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 54
4.2 INSTALLATION CONSIDERATIONS .............................................................................. 54
4.2.1 SO-DIMM Installation ..................................................................................... 56
4.2.2 iRIS-1010 Module Installation......................................................................... 56
4.2.3 PCIe Mini Card Installation ............................................................................ 58
4.3 SYSTEM CONFIGURATION ......................................................................................... 58
4.3.1 AT/ATX Power Mode Setting ........................................................................... 58
Page v
NANO-BT-i1 EPIC SBC
4.3.2 Clear CMOS Button......................................................................................... 59
4.3.3 LVDS Panel Resolution Selection .................................................................... 60
4.3.4 LCD Voltage Selection ..................................................................................... 61
4.3.5 mSATA/SATA Selection..................................................................................... 62
4.3.6 PCI-104 Voltage Selection ............................................................................... 63
4.4 INTERNAL PERIPHERAL DEVICE CONNECTIONS ........................................................ 63
4.4.1 AT Power Connection ...................................................................................... 63
4.4.2 SATA Drive Connection ................................................................................... 65
4.4.3 Single RS-232 Cable Connection..................................................................... 66
4.5 EXTERNAL PERIPHERAL INTERFACE CONNECTION ................................................... 67
4.5.1 LAN Connection............................................................................................... 67
4.5.2 PS/2 Keyboard/Mouse Connection .................................................................. 68
4.5.3 USB Connection............................................................................................... 69
4.5.4 VGA Monitor Connection ................................................................................ 70
4.6 IPMI SETUP PROCEDURE ......................................................................................... 72
4.6.1 Managed System Hardware Setup ................................................................... 72
5 BIOS .............................................................................................................................. 73
5.1 INTRODUCTION......................................................................................................... 74
5.1.1 Starting Setup................................................................................................... 74
5.1.2 Using Setup ...................................................................................................... 74
5.1.3 Getting Help..................................................................................................... 75
5.1.4 Unable to Reboot after Configuration Changes .............................................. 75
5.1.5 BIOS Menu Bar................................................................................................ 75
5.2 MAIN........................................................................................................................ 76
5.3 ADVANCED ............................................................................................................... 77
5.3.1 ACPI Settings ................................................................................................... 77
5.3.2 Super IO Configuration ................................................................................... 79
5.3.2.1 Serial Port n Configuration ....................................................................... 79
5.3.3 Hardware Monitor ........................................................................................... 84
5.3.3.1 Smart Fan Mode Configuration ................................................................ 86
5.3.4 iWDD H/W Monitor ......................................................................................... 87
5.3.4.1 Smart Fan Mode Configuration ................................................................ 89
5.3.5 RTC Wake Settings ........................................................................................... 90
5.3.6 Serial Port Console Redirection ...................................................................... 91
Page vi
NANO-BT-i1 EPIC SBC
5.3.7 CPU Configuration .......................................................................................... 93
5.3.8 IDE Configuration ........................................................................................... 96
5.3.9 USB Configuration........................................................................................... 97
5.4 CHIPSET ................................................................................................................... 98
5.4.1 North Bridge .................................................................................................... 99
5.4.1.1 Intel IGD Configuration.......................................................................... 100
5.4.2 South Bridge................................................................................................... 101
5.4.2.1 PCI Express Configuration ..................................................................... 103
5.5 SECURITY ............................................................................................................... 104
5.6 BOOT...................................................................................................................... 105
5.7 EXIT ....................................................................................................................... 107
6 SOFTWARE DRIVERS ............................................................................................ 109
6.1 AVAILABLE SOFTWARE DRIVERS .............................................................................110
6.2 SOFTWARE INSTALLATION .......................................................................................110
6.3 CHIPSET DRIVER INSTALLATION ..............................................................................112
6.4 GRAPHICS DRIVER INSTALLATION ...........................................................................115
6.5 LAN DRIVER INSTALLATION ...................................................................................118
A BIOS OPTIONS ........................................................................................................ 123
B TERMINOLOGY...................................................................................................... 126
C WATCHDOG TIMER .............................................................................................. 130
D HAZARDOUS MATERIALS DISCLOSURE ....................................................... 133
D.1 HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS
ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ..................................... 134
Page vii
NANO-BT-i1 EPIC SBC
List of Figures
Figure 1-1: NANO-BT-i1 .................................................................................................................2
Figure 1-2: Connectors (Front Side) .............................................................................................5
Figure 1-3: Connectors (Solder Side) ...........................................................................................6
Figure 1-4: NANO-BT-i1 Main Dimensions (mm).........................................................................7
Figure 1-5: NANO-BT-i1 Height Dimensions 1 (mm)...................................................................8
Figure 1-6: NANO-BT-i1 Height Dimensions 2 (mm)...................................................................8
Figure 1-7: Data Flow Diagram......................................................................................................9
Figure 3-1: Connectors and Jumpers (Front Side) ...................................................................17
Figure 3-2: Connectors and Jumpers (Solder Side) .................................................................18
Figure 3-3: CPU Power Connector Location..............................................................................21
Figure 3-4: Audio Connector Location .......................................................................................22
Figure 3-5: Battery Connector Location.....................................................................................23
Figure 3-6: Backlight Inverter Connector Location...................................................................23
Figure 3-7: Buzzer Connector Location .....................................................................................24
Figure 3-8: Chassis Intrusion Connector Location...................................................................25
Figure 3-9: Digital I/O Connector Location ................................................................................26
Figure 3-10: CPU Fan Connector Location ................................................................................27
Figure 3-11: System Fan Connector Location...........................................................................28
Figure 3-12: Front Panel Connector Location ...........................................................................29
Figure 3-13: IPMI LED Connector Location ...............................................................................30
Figure 3-14: iRIS Module Slot Location......................................................................................31
Figure 3-15: LAN LED Connector Locations .............................................................................31
Figure 3-16: LVDS Connector Location......................................................................................32
Figure 3-17: Memory Card Slot Location ...................................................................................33
Figure 3-18: PCI-104 Connector Location ..................................................................................34
Figure 3-19: PCIe Mini Card Slot Location .................................................................................36
Figure 3-20: Power Button Location...........................................................................................37
Figure 3-21: Power Button Location...........................................................................................38
Figure 3-22: Reset Button Connector Location.........................................................................39
Figure 3-23: SATA 3Gb/s Drive Connector Locations ..............................................................40
Page viii
NANO-BT-i1 EPIC SBC
Figure 3-24: SATA Power Connector Locations .......................................................................41
Figure 3-25: RS-232 Serial Port Connector Locations..............................................................42
Figure 3-26: RS-422/485 Connector Location............................................................................43
Figure 3-27: SMBus Connector Location ...................................................................................44
Figure 3-28: SPI Flash Connector Location...............................................................................45
Figure 3-29: SPI EC Flash Connector Location.........................................................................46
Figure 3-30: USB 2.0 Connector Location .................................................................................47
Figure 3-31: External Peripheral Interface Connector ..............................................................47
Figure 3-32: Ethernet Connector.................................................................................................49
Figure 3-33: HDMI Connector ......................................................................................................50
Figure 3-34: PS/2 Pinout and Configuration ..............................................................................50
Figure 3-35: VGA Connector .......................................................................................................52
Figure 4-1: SO-DIMM Installation ................................................................................................56
Figure 4-2: iRIS-1010 Module Installation ..................................................................................57
Figure 4-3: PCIe Mini Card Installation.......................................................................................58
Figure 4-4: AT/ATX Power Mode Switch Location ....................................................................59
Figure 4-5: Clear CMOS Button Location...................................................................................59
Figure 4-6: LVDS Panel Resolution Selection Switch Location ..............................................61
Figure 4-7: LCD Voltage Selection Switch Location .................................................................62
Figure 4-8: mSATA/SATA Switch Location................................................................................62
Figure 4-9: PCI-104 Voltage Switch Location ............................................................................63
Figure 4-10: Power Cable to Motherboard Connection ............................................................64
Figure 4-11: Connect Power Cable to Power Supply................................................................65
Figure 4-12: SATA Drive Cable Connection...............................................................................66
Figure 4-13: Single RS-232 Cable Installation ...........................................................................67
Figure 4-14: LAN Connection ......................................................................................................68
Figure 4-15: PS/2 Keyboard/Mouse Connector .........................................................................69
Figure 4-16: USB Connector........................................................................................................70
Figure 4-17: VGA Connector .......................................................................................................71
Figure 6-1: Driver CD Main Menu ............................................................................................. 111
Figure 6-2: Available Drivers .................................................................................................... 111
Figure 6-3: Chipset Driver Welcome Screen........................................................................... 112
Figure 6-4: Chipset Driver License Agreement ...................................................................... 113
Figure 6-5: Chipset Driver Read Me File ................................................................................. 113
Figure 6-6: Chipset Driver Setup Operations ......................................................................... 114
Page ix
NANO-BT-i1 EPIC SBC
Figure 6-7: Chipset Driver Installation Finish Screen............................................................ 114
Figure 6-8: Graphics Driver Welcome Screen ........................................................................ 116
Figure 6-9: Graphics Driver License Agreement.................................................................... 116
Figure 6-10: Graphics Driver Read Me File ............................................................................. 117
Figure 6-11: Graphics Driver Setup Operations ..................................................................... 117
Figure 6-12: Graphics Driver Installation Finish Screen ....................................................... 118
Figure 6-13: PC Properties ....................................................................................................... 119
Figure 6-14: System Control Panel .......................................................................................... 119
Figure 6-15: Device Manager List ............................................................................................ 120
Figure 6-16: Update Driver Software Window ........................................................................ 121
Figure 6-17: Locate Driver Files ............................................................................................... 121
Page x
NANO-BT-i1 EPIC SBC
List of Tables
Table 1-1: Model Variations ...........................................................................................................3
Table 1-2: NANO-BT-i1 Specifications........................................................................................11
Table 2-1: Packing List.................................................................................................................15
Table 2-2: Optional Items.............................................................................................................15
Table 3-1: Peripheral Interface Connectors ...............................................................................19
Table 3-2: Rear Panel Connectors ..............................................................................................20
Table 3-3: CPU Power Connector Pinouts .................................................................................21
Table 3-4: Audio Connector Pinouts ..........................................................................................22
Table 3-5: Battery Connector Pinouts ........................................................................................23
Table 3-6: Backlight Inverter Connector Pinouts ......................................................................24
Table 3-7: Chassis Intrusion Connector Pinouts ......................................................................25
Table 3-8: Digital I/O Connector Pinouts....................................................................................26
Table 3-9: CPU Fan Connector Pinouts......................................................................................27
Table 3-10: System Fan Connector Pinouts ..............................................................................28
Table 3-11: Front Panel Connector Pinouts...............................................................................29
Table 3-12: IPMI LED Connector Pinouts ...................................................................................30
Table 3-13: LAN1 LED Connector (JP8) Pinouts .......................................................................31
Table 3-14: LAN2 LED Connector (JP9) Pinouts .......................................................................32
Table 3-15: LVDS Connector Pinouts .........................................................................................33
Table 3-16: PCI-104 Connector Pinouts .....................................................................................35
Table 3-17: PCIe Mini Card Slot Pinouts ....................................................................................37
Table 3-18: Power Button Pinouts ..............................................................................................37
Table 3-19: Reset Button Connector Pinouts ............................................................................39
Table 3-20: SATA 3Gb/s Drive Connector Pinouts....................................................................40
Table 3-21: SATA Power Connector Pinouts.............................................................................41
Table 3-22: RS-232 Serial Port Connector Pinouts ...................................................................42
Table 3-23: RS-422/485 Connector Pinouts ...............................................................................43
Table 3-24: RS-422/485 Pinouts of D-sub 9 Connector.............................................................43
Table 3-25: SMBus Connector Pinouts ......................................................................................44
Table 3-26: SPI Flash Connector Pinouts ..................................................................................45
Page xi
NANO-BT-i1 EPIC SBC
Table 3-27: SPI EC Flash Connector Pinouts ............................................................................46
Table 3-28: USB 2.0 Connector Pinouts .....................................................................................47
Table 3-29: LAN1 Ethernet Connector Pinouts .........................................................................48
Table 3-30: LAN2 Ethernet Connector Pinouts .........................................................................48
Table 3-31: Connector LEDs........................................................................................................49
Table 3-32: HDMI Connector Pinouts .........................................................................................50
Table 3-33: Keyboard Connector Pinouts..................................................................................51
Table 3-34: USB 2.0 Port Pinouts................................................................................................51
Table 3-35: USB 3.0 Port Pinouts................................................................................................52
Table 3-36: VGA Connector Pinouts...........................................................................................52
Table 4-1: LVDS Panel Resolution Selection.............................................................................60
Table 4-2: LCD Voltage Selection Switch Settings ...................................................................61
Table 4-3: mSATA/SATA Switch Settings ..................................................................................62
Table 4-4: PCI-104 Voltage Switch Settings...............................................................................63
Table 5-1: BIOS Navigation Keys ................................................................................................75
Page xii
NANO-BT-i1 EPIC SBC
BIOS Menus
BIOS Menu 1: Main .......................................................................................................................76
BIOS Menu 2: Advanced ..............................................................................................................77
BIOS Menu 3: ACPI Configuration ..............................................................................................78
BIOS Menu 4: Super IO Configuration........................................................................................79
BIOS Menu 5: Serial Port n Configuration Menu.......................................................................79
BIOS Menu 6: Hardware Monitor.................................................................................................85
BIOS Menu 7: Smart Fan Mode Configuration ..........................................................................86
BIOS Menu 8: iWDD H/W Monitor................................................................................................88
BIOS Menu 9: Smart Fan Mode Configuration ..........................................................................89
BIOS Menu 10: RTC Wake Settings ............................................................................................90
BIOS Menu 11: Serial Port Console Redirection .......................................................................91
BIOS Menu 12: CPU Configuration .............................................................................................94
BIOS Menu 13: IDE Configuration...............................................................................................96
BIOS Menu 14: USB Configuration .............................................................................................97
BIOS Menu 15: Chipset ................................................................................................................98
BIOS Menu 16: North Bridge .......................................................................................................99
BIOS Menu 17: Intel IGD Configuration................................................................................... 100
BIOS Menu 18: South Bridge.................................................................................................... 101
BIOS Menu 19: PCI Express Configuration ............................................................................ 103
BIOS Menu 20: Security ............................................................................................................ 104
BIOS Menu 21: Boot .................................................................................................................. 105
BIOS Menu 22:Exit..................................................................................................................... 107
Page xiii
NANO-BT-i1 EPIC SBC
Chapter
1
1 Introduction
Page 1
NANO-BT-i1 EPIC SBC
1.1 Introduction
Figure 1-1: NANO-BT-i1
The NANO-BT-i1 is an EPIC form factor single bard computer. It has an on-board 22nm
Intel® Atom™ or Celeron® processor, and supports one 204-pin 1333/1066 MHz
dual-channel unbuffered DDR3 Low Voltage (DDR3L) SDRAM SO-DIMM with up to
8.0 GB of memory.
The NANO-BT-i1 features Intelligent Platform Management Interface (IPMI) that helps
lower the overall costs of server management by enabling users to maximize IT resource,
save time and manage multiple systems. The NANO-BT-i1 supports IPMI 2.0 through the
optional iRIS-1010 module.
The NANO-BT-i1 includes one VGA port and one HDMI port for dual independent display
It also has an internal 18-bit/24-bit dual-channel LVDS connector supporting up to 1920 x
1200 resolutions. Expansion and I/O include one PCI-104 slot, one PCIe Mini slot, one
USB 3.0 port plus one USB 2.0 on the rear panel, two USB 2.0 by pin header, two SATA
3Gb/s connectors, three RS-232 serial ports, and one PS/2 keyboard/mouse connector.
Page 2
NANO-BT-i1 EPIC SBC
1.2 Model Variations
There are eight models of the NANO-BT-i1 series. The model variations are listed in
Table 1-1.
Model
On-board SoC
Max. Memory Size
NANO-BT-i1-E38151
Intel® Atom™ processor E3815
4 GB
(1.46 GHz, single-core, 512 KB cache)
NANO-BT-i1-E38251
Intel® Atom™ processor E3825
4 GB
(1.33 GHz, dual-core, 1 MB cache)
NANO-BT-i1-E38261
Intel® Atom™ processor E3826
8 GB
(1.46 GHz, dual-core, 1 MB cache)
NANO-BT-i1-E38271
Intel® Atom™ processor E3827
8 GB
(1.75 GHz, dual-core, 1 MB cache)
NANO-BT-i1-E38451
Intel® Atom™ processor E3845
8 GB
(1.91 GHz, quad-core, 2 MB cache)
NANO-BT-i1-J19001
Intel® Celeron® processor J1900
8 GB
(2 GHz, quad-core, 2 MB cache)
NANO-BT-i1-N28071
Intel® Celeron® processor N2807
4 GB
(1.58 GHz, dual-core, 2 MB cache)
NANO-BT-i1-N29301
Intel® Celeron® processor N2930
8 GB
(1.83 GHz, quad-core, 2 MB cache)
Table 1-1: Model Variations
1.3 Benefits
Some of the NANO-BT-i1 motherboard benefits include:
ƒ
Powerful graphics with multiple monitors
ƒ
Staying connected with both wired LAN connections
ƒ
Speedy running of multiple programs and applications
Page 3
NANO-BT-i1 EPIC SBC
1.4 Features
Some of the NANO-BT-i1 motherboard features are listed below:
ƒ
EPIC form factor
ƒ
RoHS compliant
ƒ
On-board 22nm Intel® Atom™ or Celeron® processor
ƒ
One 204-pin 1333/1066 MHz dual-channel unbuffered DDR3L (1.35 V)
SDRAM SO-DIMM slot supports up to 8.0 GB of memory
Page 4
ƒ
LVDS, VGA and HDMI interfaces for dual independent display
ƒ
Supports IPMI 2.0 via IEI iRIS-1010 module
ƒ
Two Intel® PCIe GbE connectors
ƒ
Two SATA 3Gb/s connectors
ƒ
One PCIe Mini card expansion slot
ƒ
One PCI-104 expansion slot
ƒ
One USB 3.0 port and three USB 2.0 ports
ƒ
Three RS-232 serial ports and one RS-422/485 serial port
ƒ
High Definition Audio
NANO-BT-i1 EPIC SBC
1.5 Connectors
The connectors on the NANO-BT-i1 are shown in the figure below.
Figure 1-2: Connectors (Front Side)
Page 5
NANO-BT-i1 EPIC SBC
Figure 1-3: Connectors (Solder Side)
Page 6
NANO-BT-i1 EPIC SBC
1.6 Dimensions
The main dimensions of the NANO-BT-i1 are shown in the diagram below.
Figure 1-4: NANO-BT-i1 Main Dimensions (mm)
The height of the NANO-BT-i1 series varies depending on the heatsink installed on the
board. Figure 1-5 shows the height dimensions of the following models:
ƒ
NANO-BT-i1-E38271
ƒ
NANO-BT-i1-E38261
ƒ
NANO-BT-i1-E38251
ƒ
NANO-BT-i1-E38151
Page 7
NANO-BT-i1 EPIC SBC
ƒ
NANO-BT-i1-N28071
Figure 1-5: NANO-BT-i1 Height Dimensions 1 (mm)
Figure 1-6 shows the height dimensions of the following models:
ƒ
NANO-BT-i1-E38451
ƒ
NANO-BT-i1-J19001
ƒ
NANO-BT-i1-N29301
Figure 1-6: NANO-BT-i1 Height Dimensions 2 (mm)
Page 8
NANO-BT-i1 EPIC SBC
1.7 Data Flow
Figure 1-7 shows the data flow between the system chipset, the CPU and other
5
components installed on the motherboard.
Figure 1-7: Data Flow Diagram
Page 9
NANO-BT-i1 EPIC SBC
1.8 Technical Specifications
NANO-BT-i1 technical specifications are listed below.
Specification/Model
NANO-BT-i1
Form Factor
EPIC
On-board SoC
Intel® Atom™ processor E3845 (1.91GHz, quad-core, 2MB cache, TDP=10W)
Intel® Atom™ processor E3827 (1.75GHz, dual-core, 1MB cache, TDP=8W)
Intel® Atom™ processor E3826 (1.46GHz, dual-core, 1MB cache, TDP=7W)
Intel® Atom™ processor E3825 (1.33GHz, dual-core, 1MB cache, TDP=6W)
Intel® Atom™ processor E3815 (1.46GHz, single-core, 512KB cache, TDP=5W)
Intel® Celeron® processor J1900 (2GHz, quad-core, 2MB cache, TDP=10W)
Intel® Celeron® processor N2930 (1.83GHz, quad-core, 2MB cache, TDP=7.5W)
Intel® Celeron® processor N2807 (1.58GHz, dual-core, 2MB cache, TDP=4.5W)
Integrated Graphics
Intel® HD Graphics Gen7 with 4 execution units, supporting DirectX 11.1, OpenCL
1.2 and OpenGL 4.2
Memory
One 204-pin 1066/1333MHz single-channel unbuffered DDR3L (1.35 V) SDRAM
SO-DIMM supports up to 8 GB (J1900, N2930, E3845, E3827, E3826) or 4 GB
(N2807, E3825, E3815)
Audio
Realtek ALC662 HD Audio codec
BIOS
UEFI BIOS
Ethernet Controllers
LAN1: Intel® I210-AT PCIe Ethernet controller with NCSI and IPMI 2.0 support
LAN2: Intel® I211-AT PCIe Ethernet controller
Digital I/O
8-bit digital I/O (4-bit input, 4-bit output)
IPMI 2.0
Supported by the optional iRIS-1010 module
Super I/O Controller
Fintek F81866
Embedded Controller
ITE IT8528E
Watchdog Timer
Software programmable supports 1 sec–255 sec system reset
Expansion
PCI
Page 10
One PCI-104 slot
NANO-BT-i1 EPIC SBC
Specification/Model
NANO-BT-i1
PCIe
One PCIe Mini card slot
I/O Interface Connectors
Audio Connector
One internal audio connector (10-pin)
Display Ports
One VGA port (up to 2560 x 1600, 60Hz)
One HDMI port (up to 2560 x 1600, 60Hz)
18-bit/24-bit dual-channel LVDS (up to 1920 x 1200, 60Hz)
Ethernet
Two RJ-45 GbE ports
Keyboard/Mouse
One PS/2 keyboard/mouse connector
Serial Ports
One RS-422/485 via internal wafer connector
Three RS-232 via internal pin headers
USB ports
One external USB 3.0 port and one external USB 2.0 port on rear IO
Two internal USB 2.0 ports by pin header
Serial ATA
Two SATA 3Gb/s connectors
LAN LED
Two 2-pin LAN active LED connectors
SMBus
Supported by one 4-pin wafer connector
Environmental and Power Specifications
Power Supply
12 V only DC input through the internal 4-pin (2x2) power connector
AT/ATX power supported
Power Consumption
12 V @ 1.52 A (1.91 GHz Intel® Atom™ processor J1900 with one 8 GB
1600 MHz DDR3 memory)
Operating Temperature
-20ºC–60ºC
Storage Temperature
-30ºC–70ºC
Humidity
5%–95% (non-condensing)
Physical Specifications
Dimensions
115 mm x 165 mm
Weight GW/NW
850 g / 350 g
Table 1-2: NANO-BT-i1 Specifications
Page 11
NANO-BT-i1 EPIC SBC
Chapter
2
2 Packing List
Page 12
NANO-BT-i1 EPIC SBC
2.1 Anti-static Precautions
WARNING!
Static electricity can destroy certain electronics. Make sure to follow the
ESD precautions to prevent damage to the product, and injury to the
user.
Make sure to adhere to the following guidelines:
ƒ
Wear an anti-static wristband: Wearing an anti-static wristband can prevent
electrostatic discharge.
ƒ
Self-grounding: Touch a grounded conductor every few minutes to discharge
any excess static buildup.
ƒ
Use an anti-static pad: When configuring any circuit board, place it on an
anti-static mat.
ƒ
Only handle the edges of the PCB: Don't touch the surface of the
motherboard. Hold the motherboard by the edges when handling.
2.2 Unpacking Precautions
When the NANO-BT-i1 is unpacked, please do the following:
ƒ
Follow the antistatic guidelines above.
ƒ
Make sure the packing box is facing upwards when opening.
ƒ
Make sure all the packing list items are present.
Page 13
NANO-BT-i1 EPIC SBC
2.3 Packing List
NOTE:
If any of the components listed in the checklist below are missing, do
not proceed with the installation. Contact the IEI reseller or vendor the
NANO-BT-i1
was
purchased
from
or
contact
an
IEI
sales
representative directly by sending an email to [email protected]
3
The NANO-BT-i1 is shipped with the following components:
Quantity
Item and Part Number
1
NANO-BT-i1 single board computer
2
SATA and power cable
(P/N: 32801-000201-300-RS)
2
Single RS-232 cable
(P/N: 19800-000300-200-RS)
1
12 V AT power cable
(P/N: 32100-087100-RS)
1
Page 14
Utility CD
Image
NANO-BT-i1 EPIC SBC
Quantity
Item and Part Number
1
One Key Recovery CD
1
Quick Installation Guide
Image
Table 2-1: Packing List
2.4 Optional Items
The following are optional components which may be separately purchased:
Item and Part Number
Image
IPMI 2.0 adapter card with AST1010 BMC chip (without
KVM over IP function) for PCIe Mini socket interface
(P/N: iRIS-1010-R10)
Dual USB cable
(P/N: 32000-070301-RS)
RS-422/485 cable, 200mm
(P/N: 32205-003800-300-RS)
Keyboard and mouse Y cable
(P/N: 32006-000300-100-RS)
Table 2-2: Optional Items
Page 15
NANO-BT-i1 EPIC SBC
Chapter
3
3 Connectors
Page 16
NANO-BT-i1 EPIC SBC
3.1 Peripheral Interface Connectors
This chapter details all the jumpers and connectors.
3.1.1 NANO-BT-i1 Layout
The figures below show all the connectors and jumpers.
Figure 3-1: Connectors and Jumpers (Front Side)
Page 17
NANO-BT-i1 EPIC SBC
Figure 3-2: Connectors and Jumpers (Solder Side)
3.1.2 Peripheral Interface Connectors
The table below lists all the connectors on the board.
Connector
Type
Label
12 V DC input connector
4-pin connector
CN10
Audio connector
10-pin header
AUDIO1
Battery connector
2-pin wafer
BAT1
Backlight inverter connector
5-pin wafer
INV1
Buzzer connector
2-pin wafer
SP1
Chassis intrusion connector
2-pin header
CHASSIS1
Digital I/O connector
10-pin header
DIO1
Fan connector (CPU)
3-pin wafer
CPU_FAN1
Page 18
NANO-BT-i1 EPIC SBC
Connector
Type
Label
Fan connector (system)
3-pin wafer
SYS_FAN1
Front panel connector
6-pin wafer
CN11
iRIS module connector
Half-size PCIe Mini slot
IPMI1
IPMI LED connector
2-pin header
ID_LED2
LAN1 LED connector
2-pin header
JP8
LAN2 LED connector
2-pin header
JP9
LVDS connector
30-pin crimp
CN2
Memory card slot
DIMM slot
DIMM1
PCI-104 slot
PCI-104 slot
PC104_PLUS1
PCIe Mini slot
Full-size PCIe Mini
CN8
Power button connector
2-pin wafer
PWR_BTN1
Power button
Push button
PWR_SW1
Reset button connector
2-pin wafer
RST_BTN1
SATA 3Gb/s drive connectors
7-pin SATA connector
SATA1, SATA2
SATA power connectors (5 V)
2-pin wafer
SATA_PWR1, SATA_PWR2
Serial ports, RS-232
10-pin header
COM1, COM2, COM3
Serial port, RS-422/485
4-pin wafer
COM4
SMBus connector
4-pin wafer
CN5
SPI flash connector
6-pin header
JSPI1
SPI flash connector (EC)
6-pin header
JSPI2
USB 2.0 connector
8-pin header
USB1
Table 3-1: Peripheral Interface Connectors
Page 19
NANO-BT-i1 EPIC SBC
3.1.3 External Interface Panel Connectors
The table below lists the connectors on the external I/O panel.
Connector
Type
Label
Ethernet ports
RJ-45
LAN1, LAN2
HDMI connector
HDMI
CN12
Keyboard/Mouse connector
PS/2
PT1
USB 2.0 connector
USB 2.0
CN6
USB 3.0 connector
USB 3.0
CN7
VGA connector
15-pin female
VGA1
Table 3-2: Rear Panel Connectors
3.2 Internal Peripheral Connectors
The section describes all of the connectors on the NANO-BT-i1.
3.2.1 +12 V Power Connector
CN Label:
CN10
CN Type:
4-pin connector
CN Location:
See Figure 3-3
CN Pinouts:
See Table 3-3
The +12 V power input connector provides power to the system.
Page 20
NANO-BT-i1 EPIC SBC
Figure 3-3: CPU Power Connector Location
PIN NO.
DESCRIPTION
1
GND
2
GND
3
+12 V
4
+12 V
Table 3-3: CPU Power Connector Pinouts
3.2.2 Audio Connector
CN Label:
AUDIO1
CN Type:
10-pin header
CN Location:
See Figure 3-4
CN Pinouts:
See Table 3-4
This connector connects to speakers, a microphone and an audio input.
Page 21
NANO-BT-i1 EPIC SBC
Figure 3-4: Audio Connector Location
Pin
Description
Pin
Description
1
LINE_OUTR
2
LINEIN_R
3
ANALOG_GND
4
ANALOG_GND
5
LINE_OUTL
6
LINEIN_L
7
ANALOG_GND
8
ANALOG_GND
9
MICIN1
10
MICIN2
Table 3-4: Audio Connector Pinouts
3.2.3 Battery Connector
CAUTION:
Risk of explosion if battery is replaced by an incorrect type. Only
certified engineers should replace the on-board battery.
Dispose of used batteries according to instructions and local
regulations.
CN Label:
BAT1
CN Type:
2-pin wafer
CN Location:
See Figure 3-5
CN Pinouts:
See Table 3-5
Page 22
NANO-BT-i1 EPIC SBC
A system battery is placed in the battery holder. The battery provides power to the system
clock to retain the time when power is turned off.
Figure 3-5: Battery Connector Location
Pin
Description
1
VBATT
2
GND
Table 3-5: Battery Connector Pinouts
3.2.4 Backlight Inverter Connector
CN Label:
INV1
CN Type:
5-pin wafer
CN Location:
See Figure 3-6
CN Pinouts:
See Table 3-6
6
6
The backlight inverter connector provides power to an LCD panel.
Figure 3-6: Backlight Inverter Connector Location
Page 23
NANO-BT-i1 EPIC SBC
Pin
Description
1
BRIGHTNESS2
2
GND
3
VCC
4
GND
5
ENABKL2
Table 3-6: Backlight Inverter Connector Pinouts
3.2.5 Buzzer Connector
CN Label:
SP1
CN Type:
2-pin wafer
CN Location:
See Figure 3-7
The connector is connected to a buzzer.
Figure 3-7: Buzzer Connector Location
Page 24
NANO-BT-i1 EPIC SBC
3.2.6 Chassis Intrusion Connector
CN Label:
CHASSIS1
CN Type:
2-pin header
CN Location:
See Figure 3-8
CN Pinouts:
See Table 3-7
6
The chassis intrusion connector is for a chassis intrusion detection sensor or switch that
detects if a chassis component is removed or replaced.
Figure 3-8: Chassis Intrusion Connector Location
Pin
Description
1
+V3.3A_EC
2
CHASSIS_EC
Table 3-7: Chassis Intrusion Connector Pinouts
3.2.7 Digital I/O Connector
CN Label:
DIO1
CN Type:
10-pin header
CN Location:
See Figure 3-9
CN Pinouts:
See Table 3-8
The digital I/O connector provides programmable input and output for external devices.
The digital I/O provides 4-bit output and 4-bit input.
Page 25
NANO-BT-i1 EPIC SBC
Figure 3-9: Digital I/O Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
+5V
3
DOUT3
4
DOUT2
5
DOUT1
6
DOUT0
7
DIN3
8
DIN2
9
DIN1
10
DIN0
Table 3-8: Digital I/O Connector Pinouts
3.2.8 Fan Connector (CPU)
CN Label:
CPU_FAN1
CN Type:
3-pin wafer
CN Location:
See Figure 3-10
CN Pinouts:
See Table 3-9
The fan connector attaches to a CPU cooling fan.
Page 26
NANO-BT-i1 EPIC SBC
Figure 3-10: CPU Fan Connector Location
PIN NO.
DESCRIPTION
1
FAN_IN
2
VCC (+12 V)
3
GND
Table 3-9: CPU Fan Connector Pinouts
3.2.9 Fan Connector (System)
CN Label:
SYS_FAN1
CN Type:
3-pin wafer
CN Location:
See Figure 3-11
CN Pinouts:
See Table 3-10
Each fan connector attaches to a system cooling fan.
Page 27
NANO-BT-i1 EPIC SBC
Figure 3-11: System Fan Connector Location
PIN NO.
DESCRIPTION
1
FAN_IN
2
VCC (+12 V)
3
GND
Table 3-10: System Fan Connector Pinouts
3.2.10 Front Panel Connector
CN Label:
CN11
CN Type:
6-pin wafer
CN Location:
See Figure 3-12
CN Pinouts:
See Table 3-11
The front panel connector connects to the indicator LEDs on the computer's front panel.
Page 28
NANO-BT-i1 EPIC SBC
Figure 3-12: Front Panel Connector Location
PIN
DESCRIPTION
PIN
DESCRIPTION
1
VCC
4
PWR_LED-
2
GND
5
HDD_LED+
3
PWR_LED+
6
HDD_LED-
Table 3-11: Front Panel Connector Pinouts
3.2.11 IPMI LED Connector
CN Label:
ID_LED2
CN Type:
2-pin header
CN Location:
See Figure 3-13
CN Pinouts:
See Table 3-12
The IPMI LED connector is used to connect to the IPMI LED indicator on the chassis.
Page 29
NANO-BT-i1 EPIC SBC
Figure 3-13: IPMI LED Connector Location
Pin
Description
1
ID_LED+
2
ID_LED-
Table 3-12: IPMI LED Connector Pinouts
3.2.12 iRIS Module Slot
CN Label:
IPMI1
CN Type:
Half-size PCIe Mini slot
CN Location:
See Figure 3-14
6
The iRIS module slot is used to install the IEI iRIS-1010 IPMI 2.0 module.
WARNING:
The iRIS module slot is designed to install the IEI iRIS-1010 IPMI 2.0
module only. DO NOT install other modules into the iRIS module slot.
Doing so may cause damage to the NANO-BT-i1.
Page 30
NANO-BT-i1 EPIC SBC
Figure 3-14: iRIS Module Slot Location
3.2.13 LAN LED Connectors
CN Label:
JP8, JP9
CN Type:
2-pin header
CN Location:
See Figure 3-15
CN Pinouts:
See Table 3-13 and Table 3-14
6
6
The LAN LED connectors are used to connect to the LAN LED indicators on the chassis to
indicate users the link activities of the two LAN ports.
Figure 3-15: LAN LED Connector Locations
Pin
Description
1
VCC
2
L1_LINK_ACT-
Table 3-13: LAN1 LED Connector (JP8) Pinouts
Page 31
NANO-BT-i1 EPIC SBC
Pin
Description
1
VCC
2
L2_LINK_ACT-
Table 3-14: LAN2 LED Connector (JP9) Pinouts
3.2.14 LVDS Connector
CN Label:
CN2
CN Type:
30-pin crimp
CN Location:
See Figure 3-16
CN Pinouts:
See Table 3-15
The LVDS connector is for an LCD panel connected to the board.
Figure 3-16: LVDS Connector Location
Pin
Description
Pin
Description
1
GND
2
GND
3
LVDS_A_TX0-P
4
LVDS_ A_TX0-N
5
LVDS_ A_TX1-P
6
LVDS_ A_TX1-N
7
LVDS_ A_TX2-P
8
LVDS_ A_TX2-N
9
LVDS_ A_TXCLK-P
10
LVDS_ A_TXCLK-N
Page 32
NANO-BT-i1 EPIC SBC
Pin
Description
Pin
Description
11
LVDS_ A_TX3-P
12
LVDS_ A_TX3-N
13
GND
14
GND
15
LVDS_B_TX0-P
16
LVDS_ B_TX0-N
17
LVDS_ B_TX1-P
18
LVDS_ B_TX1-N
19
LVDS_ B_TX2-P
20
LVDS_ B_TX2-N
21
LVDS_ B_TXCLK-P
22
LVDS_ B_TXCLK-N
23
LVDS_ B_TX3-P
24
LVDS_ B_TX3-N
25
GND
26
GND
27
+LCD VCC
28
+LCD VCC
29
+LCD VCC
30
+LCD VCC
Table 3-15: LVDS Connector Pinouts
3.2.15 Memory Card Slot
CN Label:
DIMM1
CN Type:
DDR3 SO-DIMM slot
CN Location:
See Figure 3-17
6
The SO-DIMM slot is for installing DDR3 Low Voltage SO-DIMM memory modules.
Figure 3-17: Memory Card Slot Location
Page 33
NANO-BT-i1 EPIC SBC
3.2.16 PCI-104 Connector
CN Label:
PC104_PLUS1
CN Type:
PCI-104 connector
CN Location:
See Figure 3-18
CN Pinouts:
See Table 3-16
The PCI-104 connector is for installing a PCI-104 expansion card.
Figure 3-18: PCI-104 Connector Location
Pin
Row A
Row B
Row C
Row D
1
GND/5 V
TBD1
5V
AD00
2
VI/O1
AD02
AD01
+5 V
3
AD05
GND
AD04
AD03
4
C/BE0#
AD07
GND
AD06
5
GND
AD09
AD08
GND
6
AD11
VI/O2
AD10
M66EN
7
AD14
AD13
GND
AD12
8
+3.3 V
C/BE1#
AD15
+3.3 V
9
SERR#
GND
SB0#
PAR
10
GND
PERR#
+3.3 V
SDONE
11
STOP#
+3.3 V
LOCK#
GND
12
+3.3 V
TRDY#
GND
DEVSEL#
Page 34
NANO-BT-i1 EPIC SBC
Pin
Row A
Row B
Row C
Row D
13
FRAME#
GND
IRDY#
+3.3 V
14
GND
AD16
+3.3 V
C/BE2#
15
AD18
+3.3 V
AD17
GND
16
AD21
AD20
GND
AD19
17
+3.3 V
AD23
AD22
+3.3 V
18
IDSEL0
GND
IDSEL1
IDSEL2
19
AD24
C/BE3#
VI/O1
IDSEL3
20
GND
AD26
AD25
GND
21
AD29
+5 V
AD28
AD27
22
+5 V
AD30
GND
AD31
23
REQ0#
GND
REQ1#
VI/O2
24
GND
REQ2#
+5 V
GNT0#
25
GNT1#
VI/O3
GNT2#
GND
26
+5 V
CLK0
GND
CLK1
27
CLK2
+5 V
CLK3
GND
28
GND
INTD#
+5 V
RST#
29
+12 V
INTA#
INTB#
INTC#
30
-12 V
TBD2
TBD
GND/3.3 V
Table 3-16: PCI-104 Connector Pinouts
3.2.17 PCIe Mini Card Slot
CN Label:
CN8
CN Type:
PCIe Mini card slot
CN Location:
See Figure 3-19
CN Pinouts:
See Table 3-17
6
The PCIe Mini card slot is for installing PCIe Mini expansion cards, such as mSATA
modules or Wi-Fi modules.
Page 35
NANO-BT-i1 EPIC SBC
Figure 3-19: PCIe Mini Card Slot Location
Pin
Description
Pin
Description
1
PCIE_WAKE#
2
VCC3
3
N/C
4
GND
5
N/C
6
1.5 V
7
VCC3
8
N/C
9
GND
10
N/C
11
CLK-
12
N/C
13
CLK+
14
N/C
15
GND
16
N/C
17
BUF_PLT_RST#
18
GND
19
N/C
20
VCC3
21
GND
22
BUF_PLT_RST#
23
PCIE_RX4DN_M
24
VCC3
25
PCIE_RX4DP_M
26
GND
27
GND
28
1.5 V
29
GND
30
SMBCLK
31
PCIE_TX4DN_CM
32
SMBDATA
33
PCIE_TX4DP_CM
34
GND
35
GND
36
USBD3-
37
GND
38
USBD3+
39
VCC3
40
GND
41
VCC3
42
N/C
43
GND
44
RF_LINK#
Page 36
NANO-BT-i1 EPIC SBC
Pin
Description
Pin
Description
45
N/C
46
BLUELED#
47
N/C
48
1.5 V
49
N/C
50
GND
51
M-SATADET
52
VCC3
Table 3-17: PCIe Mini Card Slot Pinouts
3.2.18 Power Button Connector
CN Label:
PWR_BTN1
CN Type:
2-pin wafer
CN Location:
See Figure 3-20
CN Pinouts:
See Table 3-18
The power button connector is connected to a power switch on the system chassis.
Figure 3-20: Power Button Location
Pin
Description
1
PWRBTN_SW#
2
GND
Table 3-18: Power Button Pinouts
Page 37
NANO-BT-i1 EPIC SBC
3.2.19 Power Button
CN Label:
PWR_SW1
CN Type:
Push button
CN Location:
See Figure 3-21
The on-board power button controls system power.
Figure 3-21: Power Button Location
3.2.20 Reset Button Connector
CN Label:
RST_BTN1
CN Type:
2-pin wafer
CN Location:
See Figure 3-22
CN Pinouts:
See Table 3-19
The reset button connector is connected to a reset switch on the system chassis.
Page 38
NANO-BT-i1 EPIC SBC
Figure 3-22: Reset Button Connector Location
Pin
Description
1
PM_SYSRST_R#
2
GND
Table 3-19: Reset Button Connector Pinouts
3.2.21 SATA 3Gb/s Drive Connectors
CN Label:
SATA1, SATA2
CN Type:
7-pin SATA drive connectors
CN Location:
See Figure 3-23
CN Pinouts:
See Table 3-20
The SATA drive connectors can be connected to SATA drives.
Page 39
NANO-BT-i1 EPIC SBC
Figure 3-23: SATA 3Gb/s Drive Connector Locations
Pin
Description
1
GND
2
SATA_TX+
3
SATA_TX-
4
GND
5
SATA_RX-
6
SATA_RX+
7
GND
Table 3-20: SATA 3Gb/s Drive Connector Pinouts
3.2.22 SATA Power Connectors
CN Label:
SATA_PWR1, SATA_PWR2
CN Type:
2-pin wafer
CN Location:
See Figure 3-24
CN Pinouts:
See Table 3-21
Use the SATA Power Connector to connect to SATA device power connections.
Page 40
NANO-BT-i1 EPIC SBC
Figure 3-24: SATA Power Connector Locations
Pin
Description
1
+5VS
2
GND
Table 3-21: SATA Power Connector Pinouts
3.2.23 Serial Port Connectors, RS-232
CN Label:
COM1, COM2, COM3
CN Type:
10-pin header
CN Location:
See Figure 3-25
CN Pinouts:
See Table 3-22
The connector provides RS-232 port connection.
Page 41
NANO-BT-i1 EPIC SBC
Figure 3-25: RS-232 Serial Port Connector Locations
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
DCD
2
DSR
3
SIN
4
RTS
5
SOUT
6
CTS
7
DTR
8
RI
9
GND
10
GND
Table 3-22: RS-232 Serial Port Connector Pinouts
3.2.24 Serial Port Connector, RS-422/485
CN Label:
COM4
CN Type:
4-pin wafer
CN Location:
See Figure 3-26
CN Pinouts:
See Table 3-23
Used for RS-422/485 communications.
Page 42
NANO-BT-i1 EPIC SBC
Figure 3-26: RS-422/485 Connector Location
PIN NO.
DESCRIPTION
1
RXD422-
2
RXD422+
3
TXD422+/TXD485+
4
TXD422-/TXD485-
Table 3-23: RS-422/485 Connector Pinouts
Use the optional RS-422/485 cable to connect to a serial device. The pinouts of the
D-sub 9 connector are listed below.
RS-422 Pinouts
RS-485 Pinouts
Table 3-24: RS-422/485 Pinouts of D-sub 9 Connector
3.2.25 SMBus Connector
CN Label:
CN5
CN Type:
4-pin wafer
CN Location:
See Figure 3-27
CN Pinouts:
See Table 3-25
Page 43
NANO-BT-i1 EPIC SBC
The SMBus (System Management Bus) connector provides low-speed system
management communications.
Figure 3-27: SMBus Connector Location
PIN
DESCRIPTION
1
GND
2
SMB_DATA
3
SMB_CLK
4
+5 V
Table 3-25: SMBus Connector Pinouts
3.2.26 SPI Flash Connector
CN Label:
JSPI1
CN Type:
6-pin wafer
CN Location:
See Figure 3-28
CN Pinouts:
See Table 3-26
The SPI flash connector is used to flash the SPI ROM.
Page 44
NANO-BT-i1 EPIC SBC
Figure 3-28: SPI Flash Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+1.8 VA
4
SPI_CLK_SW
2
SPI_CS
5
SPI_SI_SW
3
SPI_SO_SW
6
GND
Table 3-26: SPI Flash Connector Pinouts
3.2.27 SPI Flash Connector, EC
CN Label:
JSPI2
CN Type:
6-pin wafer
CN Location:
See Figure 3-29
CN Pinouts:
See Table 3-27
The SPI flash connector is used to flash the EC ROM.
Page 45
NANO-BT-i1 EPIC SBC
Figure 3-29: SPI EC Flash Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+3.3 A
4
SPI_CLK_SW_EC
2
SPI_CS#0_CN_EC
5
SPI_SI_SW_EC
3
SPI_SO_SW_EC
6
GND
Table 3-27: SPI EC Flash Connector Pinouts
3.2.28 USB 2.0 Connector
CN Label:
USB1
CN Type:
8-pin header
CN Location:
See Figure 3-30
CN Pinouts:
See Table 3-28
The USB 2.0 connector connects to USB 2.0 devices. Each pin header provides two USB
2.0 ports.
Page 46
NANO-BT-i1 EPIC SBC
Figure 3-30: USB 2.0 Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+VCC_USB45
2
GND
3
DATA4-
4
DATA5+
5
DATA4+
6
DATA5-
7
GND
8
+VCC_USB45
Table 3-28: USB 2.0 Connector Pinouts
3.3 External Peripheral Interface Connector Panel
The figure below shows the external peripheral interface connector (EPIC) panel. The
EPIC panel consists of the following:
Figure 3-31: External Peripheral Interface Connector
3.3.1 Ethernet Connectors
CN Label:
LAN1, LAN2
CN Type:
RJ-45
Page 47
NANO-BT-i1 EPIC SBC
CN Location:
See Figure 3-31
CN Pinouts:
See Table 3-29 and Table 3-30
A 10/100/1000 Mb/s connection can be made to a Local Area Network. The LAN1
Ethernet connector supports IPMI 2.0.
Pin
Description
Pin
Description
G1
IO_GND
R2
TRD1N0
G2
IO_GND
R3
TRD1P1
L1
L1_100-
R4
TRD1N1
L2
L1_1000-
R5
N95788738
L3
L1_LINK_ACT-
R6
N95788617
L4
N100494685
R7
TRD1P2
N1
NC
R8
TRD1N2
N2
NC
R9
TRD1P3
R1
TRD1P0
R10
TRD1N3
Table 3-29: LAN1 Ethernet Connector Pinouts
Pin
Description
Pin
Description
G1
IO_GND_1
R2
TRD2N0
G2
IO_GND_1
R3
TRD2P1
L1
L2_100-
R4
TRD2N1
L2
L2_1000-
R5
N95934519
L3
L2_LINK_ACT-
R6
N95934513
L4
N100495197
R7
TRD2P2
N1
NC
R8
TRD2N2
N2
NC
R9
TRD2P3
R1
TRD2P0
R10
TRD2N3
Table 3-30: LAN2 Ethernet Connector Pinouts
Page 48
NANO-BT-i1 EPIC SBC
Figure 3-32: Ethernet Connector
LED
Description
LED
Description
A
on: linked
B
off: 10 Mb/s
blinking: data is being sent/received
green: 100 Mb/s
orange: 1000 Mb/s
Table 3-31: Connector LEDs
3.3.2 HDMI Connector
CN Label:
CN12
CN Type:
23-pin HDMI port
CN Location:
See Figure 3-31
CN Pinouts:
See Table 3-32
The HDMI connector can connect to an HDMI device.
Pin
Description
Pin
Description
1
HDMI_DATA2
2
GND
3
HDMI_DATA2#
4
HDMI_DATA1
5
GND
6
HDMI_DATA1#
7
HDMI_DATA0
8
GND
9
HDMI_DATA0#
10
HDMI_CLK
11
GND
12
HDMI_CLK#
13
N/C
14
N/C
15
HDMI_SCL
16
HDMI_SDA
17
GND
18
+5V
19
HDMI_HPD
20
HDMI_GND
Page 49
NANO-BT-i1 EPIC SBC
Pin
Description
Pin
Description
21
HDMI_GND
22
HDMI_GND
23
HDMI_GND
Table 3-32: HDMI Connector Pinouts
Figure 3-33: HDMI Connector
3.3.3 Keyboard/Mouse Connector
CN Label:
PT1
CN Type:
PS/2
CN Location:
See Figure 3-31
CN Pinouts:
See Table 3-33
The keyboard and mouse connector is a standard PS/2 connector.
Figure 3-34: PS/2 Pinout and Configuration
Pin
Description
1
KB DATA
2
MS DATA
3
GND
4
VCC
5
KB CLOCK
Page 50
NANO-BT-i1 EPIC SBC
Pin
Description
6
MS CLOCK
Table 3-33: Keyboard Connector Pinouts
3.3.4 USB 2.0 Connector
CN Label:
CN6
CN Type:
USB 2.0 port
CN Location:
See Figure 3-31
CN Pinouts:
See Table 3-34
The USB connector can be connected to a USB device.
Pin
Description
Pin
Description
1
USB3_PWR1
4
GND
2
DATA1_N
5
USB_GND
3
DATA1_P
6
USB_GND
Table 3-34: USB 2.0 Port Pinouts
3.3.5 USB 3.0 Connector
CN Label:
CN7
CN Type:
USB 3.0 port
CN Location:
See Figure 3-31
CN Pinouts:
See Table 3-35
The USB connector can be connected to a USB device.
Pin
Description
Pin
Description
1
USB3_PWR1
6
USB3P0_RXDP1
2
USB2P0_DM1_L
7
USB_GND
3
USB2P0_DP1_L
8
USB3P0_TXDN1_C
4
GND
9
USB3P0_TXDP1_C
Page 51
NANO-BT-i1 EPIC SBC
Pin
Description
5
USB3P0_RXDN1
Pin
Description
Table 3-35: USB 3.0 Port Pinouts
3.3.6 VGA Connector
CN Label:
VGA1
CN Type:
15-pin Female
CN Location:
See Figure 3-31
CN Pinouts:
See Table 3-36 and Figure 3-35
Both VGA connectors can be connected to monitors that accept standard VGA input for
easy dual display setup. The VGA connectors support up to 1920 x 1200 resolutions.
PIN
DESCRIPTION
PIN
DESCRIPTION
V1
RED
V2
GREEN
V3
BLUE
V4
NC
V5
GND
V6
GND
V7
GND
V8
GND
V9
VCC
V10
GND
V11
NC
V12
DDCDA
V13
HSYNC
V14
VSYNC
V15
DDCCLK
Table 3-36: VGA Connector Pinouts
Figure 3-35: VGA Connector
Page 52
NANO-BT-i1 EPIC SBC
Chapter
4
4 Installation
Page 53
NANO-BT-i1 EPIC SBC
4.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during the installation of the
NANO-BT-i1 may result in permanent damage to the NANO-BT-i1 and
severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the NANO-BT-i1. Dry climates are especially susceptible to ESD. It is therefore
critical that whenever the NANO-BT-i1 or any other electrical component is handled, the
following anti-static precautions are strictly adhered to.
ƒ
Wear an anti-static wristband: - Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.
ƒ
Self-grounding:- Before handling the board touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
ƒ
Use an anti-static pad: When configuring the NANO-BT-i1, place it on an
antic-static pad. This reduces the possibility of ESD damaging the
NANO-BT-i1.
ƒ
Only handle the edges of the PCB:-: When handling the PCB, hold the PCB
by the edges.
4.2 Installation Considerations
NOTE:
The following installation notices and installation considerations should
be read and understood before installation. All installation notices must
be strictly adhered to. Failing to adhere to these precautions may lead
to severe damage and injury to the person performing the installation.
Page 54
NANO-BT-i1 EPIC SBC
WARNING:
The installation instructions described in this manual should be
carefully followed in order to prevent damage to the components and
injury to the user.
Before and during the installation please DO the following:
ƒ
Read the user manual:
o
The user manual provides a complete description of the NANO-BT-i1
installation instructions and configuration options.
ƒ
Wear an electrostatic discharge cuff (ESD):
o
Electronic components are easily damaged by ESD. Wearing an ESD cuff
removes ESD from the body and helps prevent ESD damage.
ƒ
Place the NANO-BT-i1 on an antistatic pad:
o
When installing or configuring the motherboard, place it on an antistatic
pad. This helps to prevent potential ESD damage.
ƒ
Turn all power to the NANO-BT-i1 off:
o
When working with the NANO-BT-i1, make sure that it is disconnected
from all power supplies and that no electricity is being fed into the system.
Before and during the installation of the NANO-BT-i1 DO NOT:
ƒ
Remove any of the stickers on the PCB board. These stickers are required for
warranty validation.
ƒ
Use the product before verifying all the cables and power connectors are
properly connected.
ƒ
Allow screws to come in contact with the PCB circuit, connector pins, or its
components.
Page 55
NANO-BT-i1 EPIC SBC
4.2.1 SO-DIMM Installation
To install an SO-DIMM, please follow the steps below and refer to Figure 4-1.
Figure 4-1: SO-DIMM Installation
Step 1: Locate the SO-DIMM socket on the solder side of the NANO-BT-i1. Place the
board on an anti-static mat.
Step 2: Align the SO-DIMM with the socket. Align the notch on the memory with the
notch on the memory socket.
Step 3: Insert the SO-DIMM. Push the memory in at a 20º angle. (See Figure 4-1)
Step 4: Seat the SO-DIMM. Gently push downwards and the arms clip into place. (See
Figure 4-1)
4.2.2 iRIS-1010 Module Installation
WARNING:
The iRIS module slot is designed to install the IEI iRIS-1010 IPMI 2.0
module only. DO NOT install other modules into the iRIS module slot.
Doing so may cause damage to the NANO-BT-i1.
To install the iRIS-1010 module, please follow the steps below and refer to Figure 4-2.
Page 56
NANO-BT-i1 EPIC SBC
Figure 4-2: iRIS-1010 Module Installation
Step 1: Locate the iRIS module slot on the solder side. See Figure 3-14.
Step 2: Insert into the socket at an angle. Line up the notch on the RIS-1010 module
with the notch on the connector. Slide the RIS-1010 module into the socket at an
angle of about 20º.
Step 3: Push down until the RIS-1010 module clips into place. Push the other end of
the RIS-1010 module down until it clips into place on the plastic connector.
NOTE:
After installing the iRIS-1010 module, use LAN1 port to establish a
network connection. Please refer to Section 4.6 for IPMI setup
procedures.
Page 57
NANO-BT-i1 EPIC SBC
4.2.3 PCIe Mini Card Installation
To install the PCIe Mini card, please refer to the diagram and instructions below.
Figure 4-3: PCIe Mini Card Installation
Step 1: Insert into the socket at an angle. Line up the notch on the card with the notch
on the connector. Slide the PCIe Mini card into the socket at an angle of about
20º.
Step 2: Push down until the card clips into place. Push the other end of the card
down until it clips into place on the plastic connector.Step 0:
4.3 System Configuration
The NANO-BT-i1 is a jumperless single board computer. The system configuration is
controlled by buttons and switches. The system configuration must be performed before
installation.
4.3.1 AT/ATX Power Mode Setting
The AT and ATX power mode selection is made through the AT/ATX power mode switch
which is shown in Figure 4-4.
Page 58
NANO-BT-i1 EPIC SBC
Figure 4-4: AT/ATX Power Mode Switch Location
4.3.2 Clear CMOS Button
To reset the BIOS, remove the on-board battery and press the clear CMOS button for
three seconds or more. The clear CMOS button location is shown in Figure 4-5.
Figure 4-5: Clear CMOS Button Location
Page 59
NANO-BT-i1 EPIC SBC
4.3.3 LVDS Panel Resolution Selection
Use the SW1 DIP switch to select the resolution of the LCD panel connected to the LVDS
connector.
SW1 (4-3-2-1)
Description
0000
800x600 18-bit
0001
1024x768 18-bit
0010
1024x768 24-bit
0011
1280x768 18-bit
0100
1280x800 18-bit
0101
1280x960 18-bit
0110
1280x1024 48-bit
0111
1366x768 18-bit
1000
1366x768 24-bit
1001
1440x900 48-bit
1010
1400x1050 48-bit
1011
1600x900 48-bit
1100
1680x1050 48-bit
1101
1600x1200 48-bit
1110
1920x1080 48-bit
1111
1920x1200 48-bit
(Default)
*ON=0, OFF=1
Table 4-1: LVDS Panel Resolution Selection
Page 60
NANO-BT-i1 EPIC SBC
Figure 4-6: LVDS Panel Resolution Selection Switch Location
4.3.4 LCD Voltage Selection
The LCD voltage selection switch sets the voltage of the power supplied to the LCD panel.
The LCD Voltage Selection settings are shown in Table 4-2.
Setting
Description
A-B
+3.3 V (Default)
B-C
+5.0 V
Table 4-2: LCD Voltage Selection Switch Settings
Page 61
NANO-BT-i1 EPIC SBC
Figure 4-7: LCD Voltage Selection Switch Location
4.3.5 mSATA/SATA Selection
Use the J_SATA1 switch to select whether to automatically detect mSATA devices.
Setting
Description
A-B
Automatically detect mSATA device (Default)
B-C
Enable mSATA device
Table 4-3: mSATA/SATA Switch Settings
Figure 4-8: mSATA/SATA Switch Location
Page 62
NANO-BT-i1 EPIC SBC
4.3.6 PCI-104 Voltage Selection
Use the J_PCI104 switch to select the voltage supplied to the PCI-104 expansion module.
Setting
Description
A-B
+3.3 V (Default)
B-C
+5.0 V
Table 4-4: PCI-104 Voltage Switch Settings
Figure 4-9: PCI-104 Voltage Switch Location
4.4 Internal Peripheral Device Connections
This section outlines the installation of peripheral devices to the on-board connectors.
4.4.1 AT Power Connection
Follow the instructions below to connect the NANO-BT-i1 to an AT power supply.
WARNING:
Disconnect the power supply power cord from its AC power source to
prevent a sudden power surge to the NANO-BT-i1.
Step 1: Locate the power cable. The power cable is shown in the packing list in
Chapter 2.
Page 63
NANO-BT-i1 EPIC SBC
Step 2: Connect the Power Cable to the Motherboard. Connect the 4-pin (2x2) Molex
type power cable connector to the +12V power connector on the motherboard.
See Figure 4-10.
Figure 4-10: Power Cable to Motherboard Connection
Step 3: Connect Power Cable to Power Supply. Connect one of the 4-pin (1x4) Molex
type power cable connectors to an AT power supply. See Figure 4-11.
Page 64
NANO-BT-i1 EPIC SBC
Figure 4-11: Connect Power Cable to Power Supply
4.4.2 SATA Drive Connection
The NANO-BT-i1 is shipped with two SATA drive cables. To connect the SATA drive to
the connector, please follow the steps below.
Step 1: Locate the SATA connector and the SATA power connector. The locations of
the connectors are shown in Chapter 3.
Step 2: Insert the cable connector. Insert the cable connector into the on-board SATA
drive connector and the SATA power connector. See Figure 4-12.
Page 65
NANO-BT-i1 EPIC SBC
Figure 4-12: SATA Drive Cable Connection
Step 3: Connect the cable to the SATA disk. Connect the connector on the other end
of the cable to the connector at the back of the SATA drive. See Figure 4-12.
Step 4: To remove the SATA cable from the SATA connector, press the clip on the
connector at the end of the cable. Step 0:
4.4.3 Single RS-232 Cable Connection
The single RS-232 cable consists of one serial port connector attached to a serial
communications cable that is then attached to a D-sub 9 male connector that is mounted
onto a bracket. To install the single RS-232 cable, please follow the steps below.
Step 1: Locate the RS-232 connector. The location of the RS-232 connector is shown
in Chapter 3.
Step 2: Insert the cable connector. Align pin 1 on the on-board serial port pin header
with pin 1 on the serial port connector. Pin 1 on the serial port connector is
indicated with a white dot. Insert the connector into the serial port pin header.
See Figure 4-13.
Page 66
NANO-BT-i1 EPIC SBC
Figure 4-13: Single RS-232 Cable Installation
Step 3: Secure the bracket. The single RS-232 connector has one D-sub 9 male
connector secured to a bracket. To secure the bracket to the chassis please
refer to the reference material that came with the chassis. Step 0:
4.5 External Peripheral Interface Connection
This section describes connecting devices to the external connectors on the NANO-BT-i1.
4.5.1 LAN Connection
There are two external RJ-45 LAN connectors. The RJ-45 connectors enable connection
to an external network. To connect a LAN cable with an RJ-45 connector, please follow
the instructions below.
Step 1: Locate the RJ-45 connectors. The locations of the LAN connectors are shown
in Chapter 3.
Step 2: Align the connectors. Align the RJ-45 connector on the LAN cable with one of
the RJ-45 connectors on the NANO-BT-i1. See Figure 4-14.
Page 67
NANO-BT-i1 EPIC SBC
Figure 4-14: LAN Connection
Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN
cable RJ-45 connector into the on-board RJ-45 connector.
4.5.2 PS/2 Keyboard/Mouse Connection
The NANO-BT-i1 has a single PS/2 connector on the external peripheral interface panel.
The PS/2 connector is connected to the optional PS/2 Y-cable which can be purchased
separately. One of the PS/2 cables is connected to a keyboard and the other to a mouse
to the system. Follow the steps below to connect a keyboard and mouse to the
NANO-BT-i1.
Step 1: Locate the dual PS/2 connector. The location of the PS/2 connector is shown
in Chapter 3.
Step 2: Insert the keyboard/mouse connector. Insert the PS/2 connector on the end
of the PS/2 Y-cable into the external PS/2 connector. See Figure 4-15.
Page 68
NANO-BT-i1 EPIC SBC
Figure 4-15: PS/2 Keyboard/Mouse Connector
Step 3: Connect the keyboard and mouse. Connect the keyboard and mouse to the
appropriate connector. The keyboard and mouse connectors can be
distinguished from each other by looking at the small graphic at the top of the
connector.
4.5.3 USB Connection
The external USB Series "A" receptacle connectors provide easier and quicker access to
external USB devices. Follow the steps below to connect USB devices to the
NANO-BT-i1.
Step 1: Locate the USB Series "A" receptacle connectors. The location of the USB
Series "A" receptacle connectors are shown in Chapter 3.
Page 69
NANO-BT-i1 EPIC SBC
Step 2: Insert a USB Series "A" plug. Insert the USB Series "A" plug of a device into
the USB Series "A" receptacle on the external peripheral interface. See
Figure 4-16.
Figure 4-16: USB Connector
4.5.4 VGA Monitor Connection
The NANO-BT-i1 has one single female D-sub 15 connector on the external peripheral
interface panel. The D-sub 15 connector is connected to a CRT or VGA monitor. To
connect a monitor to the NANO-BT-i1, please follow the instructions below.
Step 1: Locate the female D-sub 15 connector. The location of the female D-sub 15
connector is shown in Chapter 3.
Step 2: Align the VGA connector. Align the male D-sub 15 connector on the VGA
screen cable with the female D-sub 15 connector on the external peripheral
interface.
Page 70
NANO-BT-i1 EPIC SBC
Step 3: Insert the VGA connector. Once the connectors are properly aligned, insert the
male connector from the VGA screen into the female connector on the
NANO-BT-i1. See Figure 4-17.
Figure 4-17: VGA Connector
Step 4: Secure the connector. Secure the D-sub 15 VGA connector from the VGA
monitor to the external interface by tightening the two retention screws on either
side of the connector. Step 0:
Page 71
NANO-BT-i1 EPIC SBC
4.6 IPMI Setup Procedure
The NANO-BT-i1 features Intelligent Platform Management Interface (IPMI) that helps
lower the overall costs of server management by enabling users to maximize IT resources,
save time and manage multiple systems. The NANO-BT-i1 supports IPMI 2.0 through the
optional iRIS-1010 module. Follow the steps below to setup IPMI.
4.6.1 Managed System Hardware Setup
The hardware configuration of the managed system (NANO-BT-i1) is described below.
Step 1: Install an iRIS-1010 module to the IPMI module socket (refer to Section 4.2.2).
Step 2: Make sure a DDR3L SO-DIMM is installed in the SO-DIMM socket.
Step 3: Connect an Ethernet cable to the RJ-45 connector labeled LAN1 (Figure 3-31).
Page 72
NANO-BT-i1 EPIC SBC
Chapter
5
5 BIOS
Page 73
NANO-BT-i1 EPIC SBC
5.1 Introduction
The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to
certain system settings. This chapter outlines the options that can be changed.
NOTE:
Some of the BIOS options may vary throughout the life cycle of the
product and are subject to change without prior notice.
5.1.1 Starting Setup
The UEFI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.
1. Press the DEL or F2 key as soon as the system is turned on or
2. Press the DEL or F2 key when the “Press DEL or F2 to enter SETUP”
message appears on the screen.
If the message disappears before the DEL or F2 key is pressed, restart the computer and
try again.
5.1.2 Using Setup
Use the arrow keys to highlight items, press ENTER to select, use the PageUp and
PageDown keys to change entries, press F1 for help and press ESC to quit. Navigation
keys are shown in Table 5-1.
Key
Function
Up arrow
Move to previous item
Down arrow
Move to next item
Left arrow
Move to the item on the left hand side
Right arrow
Move to the item on the right hand side
+
Increase the numeric value or make changes
Page 74
NANO-BT-i1 EPIC SBC
Key
Function
-
Decrease the numeric value or make changes
Esc key
Main Menu – Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu
F1 key
General help, only for Status Page Setup Menu and Option
Page Setup Menu
F2 key
Load previous values
F3 key
Load optimized defaults
F4 key
Save changes and Exit BIOS
Table 5-1: BIOS Navigation Keys
5.1.3 Getting Help
When F1 is pressed a small help window describing the appropriate keys to use and the
possible selections for the highlighted item appears. To exit the Help Window press ESC
or the F1 key again.
5.1.4 Unable to Reboot after Configuration Changes
If the computer cannot boot after changes to the system configuration is made, CMOS
defaults. Use the clear CMOS button described in Chapter 4.
5.1.5 BIOS Menu Bar
The menu bar on top of the BIOS screen has the following main items:
ƒ
Main – Changes the basic system configuration.
ƒ
Advanced – Changes the advanced system settings.
ƒ
Chipset – Changes the chipset settings.
ƒ
Boot – Changes the system boot configuration.
ƒ
Security – Sets User and Supervisor Passwords.
ƒ
Save & Exit – Selects exit options and loads default settings
Page 75
NANO-BT-i1 EPIC SBC
The following sections completely describe the configuration options found in the menu
items at the top of the BIOS screen and listed above.
5.2 Main
The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered.
The Main menu gives an overview of the basic system information.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
BIOS Information
BIOS Vendor
Core Version
Compliency
Project Version
Build Date
American Megatrends
5.009
UEFI 2.3;PI1.2
B290AR0E.ROM
02/10/2014 10:03:10
iWDD Vendor
iWDD Version
iEi
B290ER00.bin
CPU Configuration
Microcode Patch
BayTrail SoC
31e
B2 Stepping
Memory Information
Total Memory
Memory Frequency
4096 MB (LPDDR3)
1333 Mhz
Set the Date. Use Tab to
switch between Data
elements.
---------------------G0P Information
Intel(R) G0P Driver
ÅÆ: Select Screen
↑ ↓: Select Item
TXE Information
Enter Select
Sec RC Version
00.05.00.00
+ -: Change Opt.
TXE FW Version
01.00.02.1060
F1: General Help
F2: Previous Values
System Date
[Tue 03/05/2014]
F3: Optimized Defaults
System Time
[15:10:27]
F4: Save & Exit
ESC: Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
[N/A]
BIOS Menu 1: Main
The System Overview field has two user configurable fields:
Î
System Date [xx/xx/xx]
Use the System Date option to set the system date. Manually enter the day, month and
year.
Page 76
NANO-BT-i1 EPIC SBC
Î
System Time [xx:xx:xx]
Use the System Time option to set the system time. Manually enter the hours, minutes
and seconds.
5.3 Advanced
Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices
through the following sub-menus:
WARNING!
Setting the wrong values in the sections below may cause the system
to malfunction. Make sure that the settings made are compatible with
the hardware.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
>
>
>
>
>
>
>
>
>
>
ACPI Settings
Super IO Configuration
Hardware Monitor
iWDD H/W Monitor
RTC Wake Settings
Serial Port Console Redirection
CPU Configuration
IDE Configuration
USB Configuration
ICP Board
System ACPI Parameters
----------------------
ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 2: Advanced
5.3.1 ACPI Settings
The ACPI Settings menu (BIOS Menu 3) configures the Advanced Configuration and
Power Interface (ACPI) options.
Page 77
NANO-BT-i1 EPIC SBC
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
ACPI Settings
ACPI Sleep State
[S3 (Suspend to RAM)]
Select the highest ACPI
sleep state the system
will enter when the
SUSPEND button is
pressed.
---------------------ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 3: ACPI Configuration
Î
ACPI Sleep State [S3 (Suspend to RAM)]
Use the ACPI Sleep State option to specify the sleep state the system enters when it is
not being used.
Î
S3
(Suspend
RAM)
to
DEFAULT
The caches are flushed and the CPU is powered
off. Power to the RAM is maintained. The
computer returns slower to a working state, but
more power is saved.
Page 78
NANO-BT-i1 EPIC SBC
5.3.2 Super IO Configuration
Use the Super IO Configuration menu (BIOS Menu 4) to set or change the
configurations for the serial ports.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
F81866 Super IO Configuration
F81866 Super IO
> Serial Port 1
> Serial Port 2
> Serial Port 3
> Serial Port 4
Chip
Configuration
Configuration
Configuration
Configuration
Set Parameters of Serial
Port 1 (COMA)
F81866
--------------------ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 4: Super IO Configuration
5.3.2.1 Serial Port n Configuration
Use the Serial Port n Configuration menu (BIOS Menu 5) to configure the serial port n.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
Serial Port n Configuration
Serial Port
Device Settings
Enable or Disable Serial
Port (COM)
[Enabled]
IO=3F8h;IRQ=4
--------------------ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
= - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
Change Settings
[Auto]
BIOS Menu 5: Serial Port n Configuration Menu
Page 79
NANO-BT-i1 EPIC SBC
5.3.2.1.1 Serial Port 1 Configuration
Î
Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Î
Î
Disabled
Î
Enabled
Disable the serial port
DEFAULT
Enable the serial port
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Î
Auto
DEFAULT
The serial port IO port address and interrupt address
are automatically detected.
Î
Î
IO=3F8h;
Serial Port I/O port address is 3F8h and the interrupt
IRQ=4
address is IRQ4
IO=3F8h;
Serial Port I/O port address is 3F8h and the interrupt
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
Î
Serial Port I/O port address is 2F8h and the interrupt
IO=2F8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
Î
Serial Port I/O port address is 3E8h and the interrupt
IO=3E8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
Î
Serial Port I/O port address is 2E8h and the interrupt
IO=2E8h;
IRQ=3,
4,
5, 6, 7, 9,
10, 11, 12
Page 80
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
NANO-BT-i1 EPIC SBC
5.3.2.1.2 Serial Port 2 Configuration
Î
Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Î
Î
Disabled
Î
Enabled
Disable the serial port
DEFAULT
Enable the serial port
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Î
Auto
DEFAULT
The serial port IO port address and interrupt address
are automatically detected.
Î
Î
IO=2F8h;
Serial Port I/O port address is 2F8h and the interrupt
IRQ=3
address is IRQ3
IO=3F8h;
Serial Port I/O port address is 3F8h and the interrupt
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
Î
Serial Port I/O port address is 2F8h and the interrupt
IO=2F8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
Î
Serial Port I/O port address is 3E8h and the interrupt
IO=3E8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
Page 81
NANO-BT-i1 EPIC SBC
Î
Serial Port I/O port address is 2E8h and the interrupt
IO=2E8h;
IRQ=3,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
4,
5, 6, 7, 9,
10, 11, 12
5.3.2.1.3 Serial Port 3 Configuration
Î
Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Î
Î
Disabled
Î
Enabled
Disable the serial port
DEFAULT
Enable the serial port
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Î
Auto
DEFAULT
The serial port IO port address and interrupt address
are automatically detected.
Î
Î
IO=3E8h;
Serial Port I/O port address is 3E8h and the interrupt
IRQ=7
address is IRQ7
IO=3F8h;
Serial Port I/O port address is 3F8h and the interrupt
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
Î
Serial Port I/O port address is 2F8h and the interrupt
IO=2F8h;
IRQ=3,
4,
5, 6, 7, 9,
10, 11, 12
Page 82
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
NANO-BT-i1 EPIC SBC
Î
Serial Port I/O port address is 3E8h and the interrupt
IO=3E8h;
IRQ=3,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
4,
5, 6, 7, 9,
10, 11, 12
Î
Serial Port I/O port address is 2E8h and the interrupt
IO=2E8h;
IRQ=3,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
4,
5, 6, 7, 9,
10, 11, 12
Î
Serial Port I/O port address is 2F0h and the interrupt
IO=2F0h;
IRQ=3,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
4,
5, 6, 7, 9,
10, 11, 12
Î
Serial Port I/O port address is 2E0h and the interrupt
IO=2E0h;
IRQ=3,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
4,
5, 6, 7, 9,
10, 11, 12
5.3.2.1.4 Serial Port 4 Configuration
Î
Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.
Î
Î
Disabled
Î
Enabled
Disable the serial port
DEFAULT
Enable the serial port
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Î
Auto
DEFAULT
The serial port IO port address and interrupt address
are automatically detected.
Page 83
NANO-BT-i1 EPIC SBC
Î
Î
IO=2E8h;
Serial Port I/O port address is 2E8h and the interrupt
IRQ=7
address is IRQ7
IO=3F8h;
Serial Port I/O port address is 3F8h and the interrupt
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
Î
Serial Port I/O port address is 2F8h and the interrupt
IO=2F8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
Î
Serial Port I/O port address is 3E8h and the interrupt
IO=3E8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
Î
Serial Port I/O port address is 2E8h and the interrupt
IO=2E8h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
Î
Serial Port I/O port address is 2F0h and the interrupt
IO=2F0h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
Î
Serial Port I/O port address is 2E0h and the interrupt
IO=2E0h;
IRQ=3,
4,
address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12
5, 6, 7, 9,
10, 11, 12
5.3.3 Hardware Monitor
The Hardware Monitor menu (BIOS Menu 6) contains the fan configuration submenus
and displays operating temperature and system voltages.
Page 84
NANO-BT-i1 EPIC SBC
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
PC Health Status
Enable or Disable Smart
Fan
Smart Fan Function
> Smart Fan Mode Configuration
SYS Temperature
CPU_FAN1
SYS_FAN1
VIN1
VIN2
VIN3
VIN4
VCC3V
VSB3V
VSB5V
[Enabled]
:+42 C
:N/A
:N/A
:+0.864
:+1.096
:+3.060
:+1.513
:+3.312
:+3.328
:+5.112
--------------------ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
V
V
V
V
V
V
V
BIOS Menu 6: Hardware Monitor
Î
Smart Fan Function
Use the Smart Fan Function BIOS option to enable or disable the smart fan connected to
the system.
Î
Î
Disabled
Î
Enabled
Disables the smart fan.
DEFAULT
Enables the smart fan.
PC Health Status
The following system parameters and values are shown. The system parameters that are
monitored are:
ƒ
System Temperatures:
o
ƒ
Fan Speeds:
o
o
ƒ
System Temperature
CPU Fan
System Fan
Voltages:
o
o
VIN1
VIN2
Page 85
NANO-BT-i1 EPIC SBC
o
o
o
o
o
VIN3
VIN4
VCC3V
VSB3V
VSB5V
5.3.3.1 Smart Fan Mode Configuration
Use the Smart Fan Mode Configuration submenu (BIOS Menu 7) to configure smart fan
temperature and speed settings.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
Smart Fan Mode Configuration
CPU_FAN1 Smart Fan
CPU Temperature 1
CPU Temperature 2
CPU Temperature 3
CPU Temperature 4
SYS_FAN1 Smart Fan
System Temperature
System Temperature
System Temperature
System Temperature
Control
Smart Fan Mode Select
[Auto Duty-Cycle Mode]
60
50
40
30
[Auto Duty-Cycle Mode]
60
50
40
30
--------------------ÅÆ: Select Screen
Control
↑ ↓: Select Item
1
Enter Select
2
+ - Change Opt.
3
F1
General Help
4
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 7: Smart Fan Mode Configuration
Î
CPU_FAN1 Smart Fan Control/SYS_FAN1 Smart Fan Control [Auto Duty-Cycle
Mode]
Use the CPU_FAN1 Smart Fan Control/SYS_FAN1 Smart Fan Control option to
configure the CPU/System Smart Fan.
Î
Manual
The fan spins at the speed set in Manual Mode
Duty
settings.
Mode
Î
Auto
Duty-Cycle
Mode
Page 86
DEFAULT
The fan adjusts its speed using Auto Mode
settings.
NANO-BT-i1 EPIC SBC
Î
CPU/System Temperature 1
Use the + or – key to change the CPU/System Temperature 1 value. Enter a decimal
number between 1 and 100. If CPU/System temperature is higher than this setting, the fan
duty cycle is 100.
Î
CPU/System Temperature 2
Use the + or – key to change the CPU/System Temperature 2 value. Enter a decimal
number between 1 and 100. If CPU/System temperature is higher than this setting, the fan
duty cycle is 85.
Î
CPU/System Temperature 3
Use the + or – key to change the CPU/System Temperature 3 value. Enter a decimal
number between 1 and 100. If CPU/System temperature is higher than this setting, the fan
duty cycle is 70.
Î
CPU/System Temperature 4
Use the + or – key to change the CPU/System Temperature 4 value. Enter a decimal
number between 1 and 100. If CPU/System temperature is higher than this setting, the fan
duty cycle is 60. If CPU/System temperature is lower than this setting, the fan duty cycle is
50.
5.3.4 iWDD H/W Monitor
The iWDD H/W Monitor menu (BIOS Menu 8) contains the fan configuration submenus
and displays operating temperature, fan speeds and system voltages.
Page 87
NANO-BT-i1 EPIC SBC
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
PC Health Status
Smart Fan Mode Select
SYS Temperature
:+42 C
CPU_FAN1 Speed
SYS_FAN1 Speed
:N/A
:N/A
CPU_CORE
+5V
+12V
+DDR
+5VSB
+3.3V
+3.3VSB
:+1.864 V
:+5.106 V
:+12.175 V
:+1.502 V
:+4.896 V
:+3.357 V
:+3.27 V
> Smart Fan Mode Configuration
--------------------ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 8: iWDD H/W Monitor
Î
PC Health Status
The following system parameters and values are shown. The system parameters that are
monitored are:
ƒ
System Temperatures:
o
ƒ
Fan Speeds:
o
o
ƒ
CPU Fan Speed
System Fan Speed
Voltages:
o
o
o
o
o
o
o
Page 88
System Temperature
CPU_CORE
+5V
+12V
+DDR
+5VSB
+3.3V
+3.3VSB
NANO-BT-i1 EPIC SBC
5.3.4.1 Smart Fan Mode Configuration
Use the Smart Fan Mode Configuration submenu (BIOS Menu 9) to configure smart fan
temperature and speed settings.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
Smart Fan Mode Configuration
CPU_FAN1 Smart Fan Control
Auto mode fan start temperature
Auto mode fan off temperature
Auto mode fan start PWM
Auto mode fan slope PWM
SYS_FAN1 Smart Fan Control
Auto mode fan start temperature
Auto mode fan off temperature
Auto mode fan start PWM
Auto mode fan slope PWM
Smart Fan Mode Select
[Auto Mode]
50
40
30
1
[Auto Mode]
50
40
30
1
--------------------ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 9: Smart Fan Mode Configuration
Î
CPU_FAN1 Smart Fan Control/SYS_FAN1 Smart Fan Control [Auto Mode]
Use the CPU_FAN1 Smart Fan Control/SYS_FAN1 Smart Fan Control option to
configure the CPU/System Smart Fan.
Î
The fan spins at the speed set in Manual Mode
Manual Mode
settings.
Î
Auto Mode
DEFAULT
The fan adjusts its speed using Auto Mode
settings.
Î
Auto mode fan start/off temperature
Use the + or – key to change the Auto mode fan start/off temperature value. Enter a
decimal number between 1 and 100.
Page 89
NANO-BT-i1 EPIC SBC
Î
Auto mode fan start PWM
Use the + or – key to change the Auto mode fan start PWM value. Enter a decimal
number between 1 and 100.
Î
Auto mode fan slope PWM
Use the + or – key to change the Auto mode fan slope PWM value. Enter a decimal
number between 1 and 64.
5.3.5 RTC Wake Settings
The RTC Wake Settings menu (BIOS Menu 10) configures RTC wake event. The RTC
wake function is supported in ACPI (S3/S4/S5) and APM soft off modes.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
Wake System with Fixed Time
[Disabled]
Enables or Disables
system wake on alarm
event. When enabled,
system will wake on the
date: hr: min: sec
specified.
---------------------ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 10: RTC Wake Settings
Î
Wake System with Fixed Time [Disabled]
Use the Wake System with Fixed Time option to specify the time the system should be
roused from a suspended state.
Page 90
NANO-BT-i1 EPIC SBC
Î
Disabled
DEFAULT
The real time clock (RTC) cannot generate a wake
event
Î
Enabled
If selected, the following appears with values that
can be selected:
*Wake up every day
*Wake up date
*Wake up hour
*Wake up minute
*Wake up second
After setting the alarm, the computer turns itself on
from a suspend state when the alarm goes off.
5.3.6 Serial Port Console Redirection
The Serial Port Console Redirection menu (BIOS Menu 11) allows the console
redirection options to be configured. Console redirection allows users to maintain a
system remotely by re-directing keyboard input and text output through the serial port.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
COM1
Console Redirection
> Console Redirection Settings
[Disabled]
COM2
Console Redirection
> Console Redirection Settings
[Disabled]
COM3
Console Redirection
> Console Redirection Settings
[Disabled]
COM4
Console Redirection
> Console Redirection Settings
[Disabled]
Console Redirection
Enable or Disable
--------------------ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
+/-: Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 11: Serial Port Console Redirection
Page 91
NANO-BT-i1 EPIC SBC
Î
Console Redirection [Disabled]
Use Console Redirection option to enable or disable the console redirection function.
Î
Disabled
Î
Enabled
DEFAULT
Disabled the console redirection function
Enabled the console redirection function
The following options are available in the Console Redirection Settings submenu when
the Console Redirection option is enabled.
Î
Terminal Type [ANSI]
Use the Terminal Type option to specify the remote terminal type.
Î
Î
VT100
The target terminal type is VT100
Î
VT100+
The target terminal type is VT100+
Î
VT-UTF8
The target terminal type is VT-UTF8
Î
ANSI
DEFAULT
The target terminal type is ANSI
Bits per second [115200]
Use the Bits per second option to specify the serial port transmission speed. The speed
must match the other side. Long or noisy lines may require lower speeds.
Î
Î
9600
Sets the serial port transmission speed at 9600.
Î
19200
Sets the serial port transmission speed at 19200.
Î
38400
Sets the serial port transmission speed at 38400.
Î
57600
Sets the serial port transmission speed at 57600.
Î
115200
DEFAULT
Sets the serial port transmission speed at 115200.
Data Bits [8]
Use the Data Bits option to specify the number of data bits.
Î
Page 92
7
Sets the data bits at 7.
NANO-BT-i1 EPIC SBC
Î
Î
8
DEFAULT
Sets the data bits at 8.
Parity [None]
Use the Parity option to specify the parity bit that can be sent with the data bits for
detecting the transmission errors.
Î
None
Î
Even
DEFAULT
No parity bit is sent with the data bits.
The parity bit is 0 if the number of ones in the data
bits is even.
Î
The parity bit is 0 if the number of ones in the data
Odd
bits is odd.
Î
The parity bit is always 1. This option does not
Mark
provide error detection.
Î
The parity bit is always 0. This option does not
Space
provide error detection.
Î
Stop Bits [1]
Use the Stop Bits option to specify the number of stop bits used to indicate the end of a
serial data packet. Communication with slow devices may require more than 1 stop bit.
Î
1
Î
2
DEFAULT
Sets the number of stop bits at 1.
Sets the number of stop bits at 2.
5.3.7 CPU Configuration
Use the CPU Configuration BIOS menu (BIOS Menu 12) to view detailed CPU
specifications and configure the CPU.
Page 93
NANO-BT-i1 EPIC SBC
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
CPU Configuration
CPU Signature
Microcode Patch
Max CPU Speed
Min CPU Speed
Processor Cores
Intel HT Technology
Intel VT-x Technology
30673
31e
1910 MHz
500 MHz
4
Not Supported
Supported
L1 Data Cache
L1 Code Cache
L2 Cache
L3 Cache
64-bit
24 kB x 4
32 kB x 4
1024 kB x 2
Not Present
Supported
Active Processor Cores
[All]
Intel Virtualization Technology [Enabled]
EIST
[Enabled]
Number of cores to enable
in each processor
package.
---------------------ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 12: CPU Configuration
The CPU Configuration menu (BIOS Menu 12) lists the following CPU details:
ƒ
CPU Signature: Lists the CPU signature value.
ƒ
Microcode Patch: Lists the microcode patch being used.
ƒ
Max CPU Speed: Lists the maximum CPU processing speed.
ƒ
Min CPU Speed: Lists the minimum CPU processing speed.
ƒ
Processor Cores: Lists the number of the processor core
ƒ
Intel HT Technology: Indicates if Intel HT Technology is supported by the
CPU.
ƒ
Intel VT-x Technology: Indicates if Intel VT-x Technology is supported by the
CPU.
Page 94
ƒ
L1 Data Cache: Lists the amount of data storage space on the L1 cache.
ƒ
L1 Code Cache: Lists the amount of code storage space on the L1 cache.
ƒ
L2 Cache: Lists the amount of storage space on the L2 cache.
ƒ
L3 Cache: Lists the amount of storage space on the L3 cache.
NANO-BT-i1 EPIC SBC
Î
Active Processor Cores [All]
Use the Active Processor Cores BIOS option to enable numbers of cores in the
processor package.
Î
Î
All
Î
1
DEFAULT
Enable all cores in the processor package.
Enable one core in the processor package.
Intel Virtualization Technology [Enabled]
Use the Intel Virtualization Technology option to enable or disable virtualization on the
system. When combined with third party software, Intel® Virtualization technology allows
several OSs to run on the same system at the same time.
Î
Î
Disabled
Î
Enabled
Disables Intel Virtualization Technology.
DEFAULT
Enables Intel Virtualization Technology.
EIST [Enabled]
Use the EIST option to enable or disable Enhanced Intel SpeedStep® Techonology
(EIST).
Î
Disables Enhanced Intel SpeedStep®
Disabled
Techonology.
Î
Enabled
DEFAULT
Enables Enhanced Intel SpeedStep®
Techonology.
Page 95
NANO-BT-i1 EPIC SBC
5.3.8 IDE Configuration
Use the IDE Configuration menu (BIOS Menu 13) to change and/or set the configuration
of the SATA devices installed in the system.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
Serial-ATA (SATA)
SATA Mode
[Enabled]
[IDE Mode]
SATA1
Not Present
Enable/Disable Serial
ATA
---------------------
ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
SATA2
Not Present
BIOS Menu 13: IDE Configuration
Î
Serial-ATA (SATA) [Enabled]
Use the Serial-ATA (SATA) option to enable or disable the serial ATA controller.
Î
Î
Enabled
Î
Disabled
DEFAULT
Enables the on-board SATA controller.
Disables the on-board SATA controller.
SATA Mode Selection [IDE Mode]
Use the SATA Mode Selection option to configure SATA devices as normal IDE devices.
Î
IDE Mode
Î
AHCI Mode
Page 96
DEFAULT
Configures SATA devices as normal IDE device.
Configures SATA devices as AHCI device.
NANO-BT-i1 EPIC SBC
5.3.9 USB Configuration
Use the USB Configuration menu (BIOS Menu 14) to read USB configuration
information and configure the USB settings.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
USB Configuration
USB Devices:
1 Keyboard, 3 Hubs
Legacy USB Support
[Enabled]
Enables Legacy USB
support. AUTO option
disables legacy support
if no USB devices are
connected. DISABLE
option will keep USB
devices available only
for EFI applications.
--------------------ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 14: USB Configuration
Î
USB Devices
The USB Devices Enabled field lists the USB devices that are enabled on the system
Î
Legacy USB Support [Enabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support. Normally if this option is not enabled, any attached USB mouse or USB keyboard
does not become available until a USB compatible operating system is fully booted with all
USB drivers loaded. When this option is enabled, any attached USB mouse or USB
keyboard can control the system even when there is no USB driver loaded onto the
system.
Î
Enabled
DEFAULT
Legacy USB support enabled
Page 97
NANO-BT-i1 EPIC SBC
Î
Disabled
Legacy USB support disabled
Î
Auto
Legacy USB support disabled if no USB devices are
connected
5.4 Chipset
Use the Chipset menu (BIOS Menu 15) to access the North Bridge and South Bridge
subsystem configuration menus.
WARNING!
Setting the wrong values for the Chipset BIOS selections in the Chipset
BIOS menu may cause the system to malfunction.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
> North Bridge
> South Bridge
North Bridge Parameters.
--------------------ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 15: Chipset
Page 98
NANO-BT-i1 EPIC SBC
5.4.1 North Bridge
Use the North Bridge menu (BIOS Menu 16) to configure the north bridge parameters.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Chipset
> Intel IGD Configuration
Configure Intel IGD
Settings.
Memory Information
Total Memory
DIMM1
4096 MB (LPDDR3)
--------------------ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
4096 MB (LPDDR3)
BIOS Menu 16: North Bridge
Page 99
NANO-BT-i1 EPIC SBC
5.4.1.1 Intel IGD Configuration
Use the Intel IGD Configuration submenu (BIOS Menu 17) to configure the graphics
settings.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Chipset
Intel IGD Configuration
Primary Display
DVMT Pre-Allocated
DVMT Total Gfx Mem
[IGD]
[64M]
[256MB]
Select which of IGD/PCI
Graphics device should
be Primary Display.
--------------------ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 17: Intel IGD Configuration
Î
Primary Display [IGD]
Use the Primary Display option to select the display device used by the system when it
boots. Configuration options are listed below.
Î
ƒ
Auto
ƒ
IGD
ƒ
PCI
ƒ
SG
DEFAULT
DVMT Pre-Allocated [64M]
Use the DVMT Pre-Allocated option to specify the amount of system memory that can be
used by the internal graphics device.
Î
Page 100
64M
DEFAULT
64 MB of memory used by internal graphics device
NANO-BT-i1 EPIC SBC
Î
128 MB of memory used by internal graphics
128M
device
Î
256 MB of memory used by internal graphics
256M
device
Î
512 MB of memory used by internal graphics
512M
device
Î
DVMT Total Gfx Mem [256MB]
Use the DVMT Total Gfx Mem option to specify the maximum amount of memory that can
be allocated as graphics memory. Configuration options are listed below.
ƒ
128MB
ƒ
256MB
ƒ
Max
Default
5.4.2 South Bridge
Use the South Bridge menu (BIOS Menu 18) to configure the south bridge parameters.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Chipset
Auto Power Button Status
[Disabled (ATX)]
Restore AC Power Loss
[Last State]
Select AC power state
when power is re-applied
after a power failure.
> PCI Express Configuration
Audio Configuration
Audio Controller
--------------------ÅÆ: Select Screen
↑ ↓: Select Item
USB Configuration
Enter Select
USB 2.0(EHCI) Support
[Enabled]
+ - Change Opt.
XHCI Mode
[Disabled]
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
[Enabled]
BIOS Menu 18: South Bridge
Page 101
NANO-BT-i1 EPIC SBC
Î
Restore on AC Power Loss [Last State]
Use the Restore on AC Power Loss BIOS option to specify what state the system
returns to if there is a sudden loss of power to the system.
Î
Power Off
The system remains turned off
Î
Power On
The system turns on
Î
Last State
DEFAULT
The system returns to its previous state. If it was on, it
turns itself on. If it was off, it remains off.
Î
Audio Controller [Enabled]
Use the Audio Controller BIOS option to enable or disable the High Definition Audio
controller.
Î
Î
Disabled
Î
Enabled
The High Definition Audio controller is disabled.
DEFAULT
The High Definition Audio controller is enabled.
USB 2.0(EHCI) Support [Enabled]
Use the USB 2.0(EHCI) Support BIOS option to enable or disable the USB EHCI (USB
2.0). One EHCI controller must always be enabled.
Î
Enabled
Î
Disabled
Page 102
DEFAULT
The USB EHCI is enabled.
The USB EHCI is disabled.
NANO-BT-i1 EPIC SBC
5.4.2.1 PCI Express Configuration
Use the PCI Express Configuration submenu (BIOS Menu 19) to configure the PCI
Express slots.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Chipset
PCI Express Configuration
PCI-E Mini Card (CN8)
Speed
[Enabled]
[Auto]
Enable or Disable the PCI
Express Port 2 in the
Chipset.
--------------------ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 19: PCI Express Configuration
Î
PCI-E Mini Card (CN8) [Enabled]
Use the PCI-E Mini Card (CN8) option to enable or disable the PCIe Mini card slot (CN8).
Î
Î
Enabled
Î
Disabled
DEFAULT
The PCIe Mini card slot (CN8) is enabled.
The PCIe Mini card slot (CN8) is disabled.
Speed [Auto]
Use the Speed option to configure the PCIe Mini card slot (CN8) speed.
ƒ
Auto
ƒ
Gen 2
ƒ
Gen 1
DEFAULT
Page 103
NANO-BT-i1 EPIC SBC
5.5 Security
Use the Security menu (BIOS Menu 20) to set system and user passwords.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
Password Description
If ONLY the Administrator’s password is set,
then this only limits access to Setup and is
only asked for when entering Setup.
If ONLY the User’s password is set, then this
is a power on password and must be entered to
boot or enter Setup. In Setup the User will
have Administrator rights.
The password must be
In the following range:
Maximum length
3
Minimum length
20
Set Administrator
Password
--------------------ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Administrator Password
User Password
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 20: Security
Î
Administrator Password
Use the Administrator Password to set or change a administrator password.
Î
User Password
Use the User Password to set or change a user password.
Page 104
NANO-BT-i1 EPIC SBC
5.6 Boot
Use the Boot menu (BIOS Menu 21) to configure system boot options.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
Boot Configuration
Bootup NumLock State
Quiet Boot
UEFI Boot
OS Selection
[On]
[Enabled]
[Disabled]
[Windows 8.X]
Select the keyboard
NumLock state
--------------------ÅÆ: Select Screen
Launch PXE OpROM
[Disabled]
↑ ↓: Select Item
Launch Video OpROM
[Legacy only]
Enter Select
Option ROM Messages
[Force BIOS]
+ - Change Opt.
F1
General Help
Boot Option Priorities
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 21: Boot
Î
Bootup NumLock State [On]
Use the Bootup NumLock State BIOS option to specify if the number lock setting must
be modified during boot up.
Î
On
DEFAULT
Allows the Number Lock on the keyboard to be
enabled automatically when the computer system
boots up. This allows the immediate use of the
10-key numeric keypad located on the right side of
the keyboard. To confirm this, the Number Lock LED
light on the keyboard is lit.
Î
Off
Does not enable the keyboard Number Lock
automatically. To use the 10-keys on the keyboard,
press the Number Lock key located on the upper
left-hand corner of the 10-key pad. The Number
Lock LED on the keyboard lights up when the
Number Lock is engaged.
Page 105
NANO-BT-i1 EPIC SBC
Î
Quiet Boot [Enabled]
Use the Quiet Boot BIOS option to select the screen display when the system boots.
Î
Î
Disabled
Î
Enabled
Normal POST messages displayed
DEFAULT
OEM Logo displayed instead of POST messages
UEFI Boot [Disabled]
Use the UEFI Boot option to enable or disable to boot from a UEFI device.
Î
Î
Enabled
Î
Disabled
Enable to boot from a UEFI device.
DEFAULT
Disable to boot from a UEFI device.
OS Selection [Windows 8.X]
Use the OS Selection option to select an operating system for the system.
Î
ƒ
Windows 8.X
ƒ
Android
ƒ
Windows 7
DEFAULT
Launch PXE OpROM [Disabled]
Use the Launch PXE OpROM option to enable or disable boot option for legacy network
devices.
Î
Î
Disabled
Î
Enabled
DEFAULT
Ignore all PXE Option ROMs
Load PXE Option ROMs
Launch Video OpROM [Legacy only]
Use the Launch Video OpROM option to launch UEFI or legacy video OpROM.
Î
Do
not
Do not launch video OpROM.
launch
Î
Page 106
UEFI only
Launch UEFI video OpROM.
NANO-BT-i1 EPIC SBC
Î
Legacy
DEFAULT
Launch legacy video OpROM.
only
Î
Option ROM Messages [Force BIOS]
Use the Option ROM Messages option to set the Option ROM display mode.
Î
Force
DEFAULT
Sets display mode to force BIOS.
BIOS
Î
Keep
Sets display mode to current.
Current
5.7 Exit
Use the Exit menu (BIOS Menu 22) to load default BIOS values, optimal failsafe values
and to save configuration changes.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
Save Changes and Reset
Discard Changes and Reset
Exit the system after
saving the changes.
Restore Defaults
Save as User Defaults
Restore User Defaults
--------------------ÅÆ: Select Screen
↑ ↓: Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 22:Exit
Page 107
NANO-BT-i1 EPIC SBC
Î
Save Changes and Reset
Use the Save Changes and Reset option to save the changes made to the BIOS options
and reset the system.
Î
Discard Changes and Reset
Use the Discard Changes and Reset option to exit the system without saving the
changes made to the BIOS configuration setup program.
Î
Restore Defaults
Use the Restore Defaults option to load the optimal default values for each of the
parameters on the Setup menus. F3 key can be used for this operation.
Î
Save as User Defaults
Use the Save as User Defaults option to save the changes done so far as user defaults.
Î
Restore User Defaults
Use the Restore User Defaults option to restore the user defaults to all the setup options.
Page 108
NANO-BT-i1 EPIC SBC
Chapter
6
6 Software Drivers
Page 109
NANO-BT-i1 EPIC SBC
6.1 Available Software Drivers
NOTE:
The content of the CD may vary throughout the life cycle of the product
and is subject to change without prior notice. Visit the IEI website or
contact technical support for the latest updates.
The following drivers can be installed on the system:
ƒ
Chipset
ƒ
Graphics
ƒ
LAN
Installation instructions are given below.
6.2 Software Installation
All the drivers for the NANO-BT-i1 are on the CD that came with the system. To install the
drivers, please follow the steps below.
Step 1: Insert the CD into a CD drive connected to the system.
NOTE:
If the installation program doesn't start automatically:
Click "Start->My Computer->CD Drive->autorun.exe"
Step 2: The driver main menu appears (Figure 6-1).
Step 3: Click NANO-BT-i1.
Page 110
NANO-BT-i1 EPIC SBC
Figure 6-1: Driver CD Main Menu
Step 4: A new screen with a list of available drivers appears (Figure 6-2).
Figure 6-2: Available Drivers
Page 111
NANO-BT-i1 EPIC SBC
Step 5: Install all of the necessary drivers in the menu.
6.3 Chipset Driver Installation
To install the chipset driver, please do the following.
Step 1: Access the driver list. (See Section 6.2)
Step 2: Click “1-Bay Trail SOC” and select the folder which corresponds to the
operating system.
NOTE:
The remainder of this installation assumes Windows 8 as the operating
system.
Step 3: Locate the setup file (infinst_autol_9.4.4.1006.exe) and double click on it.
Step 4: When the setup files are completely extracted, the Welcome Screen in Figure
6-3 appears. Click Next to continue.
Figure 6-3: Chipset Driver Welcome Screen
Page 112
NANO-BT-i1 EPIC SBC
Step 5: The License Agreement in Figure 6-4 appears.
Step 6: Click Yes to accept the agreement and continue.
Figure 6-4: Chipset Driver License Agreement
Step 7: The Read Me file in Figure 6-5 appears.
Step 8: Click Next to continue.
Figure 6-5: Chipset Driver Read Me File
Page 113
NANO-BT-i1 EPIC SBC
Step 9: Setup Operations are performed as shown in Figure 6-6.
Step 10: Once the Setup Operations are complete, click Next to continue.
Figure 6-6: Chipset Driver Setup Operations
Step 11: The Finish screen in Figure 6-7 appears.
Step 12: Select “Yes, I want to restart this computer now” and click Finish. Step 0:
Figure 6-7: Chipset Driver Installation Finish Screen
Page 114
NANO-BT-i1 EPIC SBC
6.4 Graphics Driver Installation
To install the Graphics driver, please do the following.
Step 1: Access the driver list. (See Section 6.2)
Step 2: Click “1-Bay Trail SOC” and select the folder which corresponds to the
operating system.
NOTE:
The remainder of this installation assumes Windows 8 as the operating
system.
Step 3: Unzip the file called 15.33.7.3366.zip, and then locate the setup file and double
click on it to start the installation. If a 64-bit operating system is installed, please
unzip the 15.33.7.64.336.zip file to install the graphics driver.
NOTE:
To install graphics driver on a 32-bit Windows 7 system, unzip
INTEL_EMGD.WIN7_PC_VERSION_36_15_0_1064.7Z.
To install graphics driver on a 64-bit Windows 7 system, unzip
INTEL_EMGD.WIN7_BETA_VERSION_37_15_0_1055.7Z.
Step 4: The Welcome Screen in Figure 6-8 appears.
Step 5: Click Next to continue.
Page 115
NANO-BT-i1 EPIC SBC
Figure 6-8: Graphics Driver Welcome Screen
Step 6: The License Agreement in Figure 6-9 appears.
Step 7: Click Yes to accept the agreement and continue.
Figure 6-9: Graphics Driver License Agreement
Step 8: The Read Me file in Figure 6-10 appears. Click Next to continue.
Page 116
NANO-BT-i1 EPIC SBC
Figure 6-10: Graphics Driver Read Me File
Step 9: Setup Operations are performed as shown in Figure 6-11.
Step 10: Once the Setup Operations are complete, click Next to continue.
Figure 6-11: Graphics Driver Setup Operations
Step 11: The system starts installing the Graphics Driver.
Step 12: The Finish screen in Figure 6-12 appears.
Page 117
NANO-BT-i1 EPIC SBC
Step 13: Select “Yes, I want to restart this computer now” and click Finish. Step 0:
Figure 6-12: Graphics Driver Installation Finish Screen
6.5 LAN Driver Installation
To install the LAN driver, please do the following.
Step 1: Right-click This PC icon on the desktop and select Properties. (Figure 6-13).
Page 118
NANO-BT-i1 EPIC SBC
Figure 6-13: PC Properties
Step 2: The system control panel window in Figure 6-14 appears.
Step 3: Click the Device Manager link (Figure 6-14).
Figure 6-14: System Control Panel
Page 119
NANO-BT-i1 EPIC SBC
Step 4: A list of system hardware devices appears (Figure 6-15).
Step 5: Right-click one of the Ethernet controllers that has question marks next to it (this
means Windows does not recognize the device).
Step 6: Select Update Driver Software. See Figure 6-15.
Figure 6-15: Device Manager List
Step 7: The Update Driver Software Window appears (Figure 6-16).
Page 120
NANO-BT-i1 EPIC SBC
Figure 6-16: Update Driver Software Window
Step 8: Select “Browse my computer for driver software” and click NEXT to continue.
Step 9: Click Browse to select “X:\2-LAN\Intel” directory in the Locate File window,
where “X:\” is the system CD drive. (Figure 6-17).
Figure 6-17: Locate Driver Files
Step 10: Click NEXT to continue.
Page 121
NANO-BT-i1 EPIC SBC
Step 11: Driver Installation is performed. When the Finish screen appears, click Close to
exit.
Step 12: Right-click the other Ethernet controller that has question marks next to it as
shown in Figure 6-15. Repeat Step 6–Step 11 to install the second Ethernet
controller driver. Step 0:
Page 122
NANO-BT-i1 EPIC SBC
Appendix
A
A BIOS Options
Page 123
NANO-BT-i1 EPIC SBC
Below is a list of BIOS configuration options in the BIOS chapter.
System Date [xx/xx/xx] ........................................................................................................76
System Time [xx:xx:xx] .......................................................................................................77
ACPI Sleep State [S3 (Suspend to RAM)]..........................................................................78
Serial Port [Enabled]............................................................................................................80
Change Settings [Auto] .......................................................................................................80
Serial Port [Enabled]............................................................................................................81
Change Settings [Auto] .......................................................................................................81
Serial Port [Enabled]............................................................................................................82
Change Settings [Auto] .......................................................................................................82
Serial Port [Enabled]............................................................................................................83
Change Settings [Auto] .......................................................................................................83
Smart Fan Function .............................................................................................................85
PC Health Status ..................................................................................................................85
CPU_FAN1 Smart Fan Control/SYS_FAN1 Smart Fan Control [Auto Duty-Cycle Mode]
...............................................................................................................................................86
CPU/System Temperature 1................................................................................................87
CPU/System Temperature 2................................................................................................87
CPU/System Temperature 3................................................................................................87
CPU/System Temperature 4................................................................................................87
PC Health Status ..................................................................................................................88
CPU_FAN1 Smart Fan Control/SYS_FAN1 Smart Fan Control [Auto Mode] .................89
Auto mode fan start/off temperature .................................................................................89
Auto mode fan start PWM ...................................................................................................90
Auto mode fan slope PWM..................................................................................................90
Wake System with Fixed Time [Disabled] .........................................................................90
Console Redirection [Disabled] .........................................................................................92
Terminal Type [ANSI]...........................................................................................................92
Bits per second [115200].....................................................................................................92
Data Bits [8] ..........................................................................................................................92
Parity [None].........................................................................................................................93
Stop Bits [1] ..........................................................................................................................93
Active Processor Cores [All] ..............................................................................................95
Intel Virtualization Technology [Enabled] .........................................................................95
Page 124
NANO-BT-i1 EPIC SBC
EIST [Enabled]......................................................................................................................95
Serial-ATA (SATA) [Enabled] ..............................................................................................96
SATA Mode Selection [IDE Mode] ......................................................................................96
USB Devices .........................................................................................................................97
Legacy USB Support [Enabled]..........................................................................................97
Primary Display [IGD] ....................................................................................................... 100
DVMT Pre-Allocated [64M] ............................................................................................... 100
DVMT Total Gfx Mem [256MB] ......................................................................................... 101
Restore on AC Power Loss [Last State] ......................................................................... 102
Audio Controller [Enabled] .............................................................................................. 102
USB 2.0(EHCI) Support [Enabled] ................................................................................... 102
PCI-E Mini Card (CN8) [Enabled]..................................................................................... 103
Speed [Auto]...................................................................................................................... 103
Administrator Password .................................................................................................. 104
User Password .................................................................................................................. 104
Bootup NumLock State [On]............................................................................................ 105
Quiet Boot [Enabled] ........................................................................................................ 106
UEFI Boot [Disabled] ........................................................................................................ 106
OS Selection [Windows 8.X] ............................................................................................ 106
Launch PXE OpROM [Disabled] ...................................................................................... 106
Launch Video OpROM [Legacy only].............................................................................. 106
Option ROM Messages [Force BIOS].............................................................................. 107
Save Changes and Reset ................................................................................................. 108
Discard Changes and Reset ............................................................................................ 108
Restore Defaults ............................................................................................................... 108
Save as User Defaults ...................................................................................................... 108
Restore User Defaults ...................................................................................................... 108
Page 125
NANO-BT-i1 EPIC SBC
Appendix
B
B Terminology
Page 126
NANO-BT-i1 EPIC SBC
AC ’97
Audio Codec 97 (AC’97) refers to a codec standard developed by Intel®
in 1997.
ACPI
Advanced Configuration and Power Interface (ACPI) is an OS-directed
configuration, power management, and thermal management interface.
AHCI
Advanced Host Controller Interface (AHCI) is a SATA Host controller
register-level interface.
ATA
The Advanced Technology Attachment (ATA) interface connects storage
devices including hard disks and CD-ROM drives to a computer.
ARMD
An ATAPI Removable Media Device (ARMD) is any ATAPI device that
supports removable media, besides CD and DVD drives.
ASKIR
Amplitude Shift Keyed Infrared (ASKIR) is a form of modulation that
represents a digital signal by varying the amplitude (“volume”) of the
signal. A low amplitude signal represents a binary 0, while a high
amplitude signal represents a binary 1.
BIOS
The Basic Input/Output System (BIOS) is firmware that is first run when
the computer is turned on and can be configured by the end user
CODEC
The Compressor-Decompressor (CODEC) encodes and decodes digital
audio data on the system.
CMOS
Complimentary metal-oxide-conductor is an integrated circuit used in
chips like static RAM and microprocessors.
COM
COM refers to serial ports. Serial ports offer serial communication to
expansion devices. The serial port on a personal computer is usually a
male D-sub 9 connector.
DAC
The Digital-to-Analog Converter (DAC) converts digital signals to analog
signals.
DDR
Double Data Rate refers to a data bus transferring data on both the rising
and falling edges of the clock signal.
DMA
Direct Memory Access (DMA) enables some peripheral devices to
bypass the system processor and communicate directly with the system
memory.
Page 127
NANO-BT-i1 EPIC SBC
DIMM
Dual Inline Memory Modules are a type of RAM that offer a 64-bit data
bus and have separate electrical contacts on each side of the module.
DIO
The digital inputs and digital outputs are general control signals that
control the on/off circuit of external devices or TTL devices. Data can be
read or written to the selected address to enable the DIO functions.
EHCI
The Enhanced Host Controller Interface (EHCI) specification is a
register-level interface description for USB 2.0 Host Controllers.
EIDE
Enhanced IDE (EIDE) is a newer IDE interface standard that has data
transfer rates between 4.0 MBps and 16.6 MBps.
EIST
Enhanced Intel® SpeedStep Technology (EIST) allows users to modify
the power consumption levels and processor performance through
application software. The application software changes the bus-to-core
frequency ratio and the processor core voltage.
FSB
The Front Side Bus (FSB) is the bi-directional communication channel
between the processor and the Northbridge chipset.
GbE
Gigabit Ethernet (GbE) is an Ethernet version that transfers data at 1.0
Gbps and complies with the IEEE 802.3-2005 standard.
GPIO
General purpose input
HDD
Hard disk drive (HDD) is a type of magnetic, non-volatile computer
storage device that stores digitally encoded data.
ICH
The Input/Output Control Hub (ICH) is an Intel® Southbridge chipset.
IrDA
Infrared Data Association (IrDA) specify infrared data transmission
protocols used to enable electronic devices to wirelessly communicate
with each other.
L1 Cache
The Level 1 Cache (L1 Cache) is a small memory cache built into the
system processor.
L2 Cache
The Level 2 Cache (L2 Cache) is an external processor memory cache.
LCD
Liquid crystal display (LCD) is a flat, low-power display device that
consists of two polarizing plates with a liquid crystal panel in between.
Page 128
NANO-BT-i1 EPIC SBC
LVDS
Low-voltage differential signaling (LVDS) is a dual-wire, high-speed
differential electrical signaling system commonly used to connect LCD
displays to a computer.
POST
The Power-on Self Test (POST) is the pre-boot actions the system
performs when the system is turned-on.
RAM
Random Access Memory (RAM) is volatile memory that loses data when
power is lost. RAM has very fast data transfer rates compared to other
storage like hard drives.
SATA
Serial ATA (SATA) is a serial communications bus designed for data
transfers between storage devices and the computer chipsets. The SATA
bus has transfer speeds up to 1.5 Gbps and the SATA II bus has data
transfer speeds of up to 3.0 Gbps.
S.M.A.R.T
Self Monitoring Analysis and Reporting Technology (S.M.A.R.T) refers to
automatic status checking technology implemented on hard disk drives.
UART
Universal Asynchronous Receiver-transmitter (UART) is responsible for
asynchronous communications on the system and manages the system’s
serial communication (COM) ports.
UHCI
The Universal Host Controller Interface (UHCI) specification is a
register-level interface description for USB 1.1 Host Controllers.
USB
The Universal Serial Bus (USB) is an external bus standard for
interfacing devices. USB 1.1 supports 12Mbps data transfer rates and
USB 2.0 supports 480Mbps data transfer rates.
VGA
The Video Graphics Array (VGA) is a graphics display system developed
by IBM.
Page 129
NANO-BT-i1 EPIC SBC
Appendix
C
C Watchdog Timer
Page 130
NANO-BT-i1 EPIC SBC
NOTE:
The following discussion applies to DOS environment. Contact IEI support
or visit the IEI website for specific drivers for other operating systems.
The Watchdog Timer is provided to ensure that standalone systems can always recover
from catastrophic conditions that cause the CPU to crash. This condition may have
occurred by external EMIs or a software bug. When the CPU stops working correctly,
Watchdog Timer either performs a hardware reset (cold boot) or a Non-Maskable Interrupt
(NMI) to bring the system back to a known state.
A BIOS function call (INT 15H) is used to control the Watchdog Timer.
INT 15H:
AH – 6FH Sub-function:
AL – 2:
Sets the Watchdog Timer’s period.
BL:
Time-out value (Its unit-second is dependent on the item “Watchdog
Timer unit select” in CMOS setup).
Table C-1: AH-6FH Sub-function
Call sub-function 2 to set the time-out period of Watchdog Timer first. If the time-out value
is not zero, the Watchdog Timer starts counting down. When the timer value reaches zero,
the system resets. To ensure that this reset condition does not occur, calling sub-function
2 must periodically refresh the Watchdog Timer. However, the watchdog timer is disabled
if the time-out value is set to zero.
A tolerance of at least 10% must be maintained to avoid unknown routines within the
operating system (DOS), such as disk I/O that can be very time-consuming.
Page 131
NANO-BT-i1 EPIC SBC
NOTE:
When exiting a program it is necessary to disable the Watchdog Timer,
otherwise the system resets.
EXAMPLE PROGRAM:
; INITIAL TIMER PERIOD COUNTER
;
W_LOOP:
;
MOV
AX, 6F02H
;setting the time-out value
MOV
BL, 30
;time-out value is 48 seconds
INT
15H
;
; ADD THE APPLICATION PROGRAM HERE
;
CMP
JNE
; EXIT ;
Page 132
W_LOOP
MOV
AX, 6F02H
MOV
BL, 0
INT
;
EXIT_AP, 1
15H
;is the application over?
;No, restart the application
;disable Watchdog Timer
;
NANO-BT-i1 EPIC SBC
Appendix
D
D Hazardous Materials
Disclosure
Page 133
NANO-BT-i1 EPIC SBC
D.1 Hazardous Materials Disclosure Table for IPB Products
Certified as RoHS Compliant Under 2002/95/EC Without
Mercury
The details provided in this appendix are to ensure that the product is compliant with the
Peoples Republic of China (China) RoHS standards. The table below acknowledges the
presences of small quantities of certain materials in the product, and is applicable to China
RoHS only.
A label will be placed on each product to indicate the estimated “Environmentally Friendly
Use Period” (EFUP). This is an estimate of the number of years that these substances
would “not leak out or undergo abrupt change.” This product may contain replaceable
sub-assemblies/components which have a shorter EFUP such as batteries and lamps.
These components will be separately marked.
Please refer to the table on the next page.
Page 134
NANO-BT-i1 EPIC SBC
Part Name
Toxic or Hazardous Substances and Elements
Lead
Mercury
Cadmium
Hexavalent
Polybrominated
Polybrominated
(Pb)
(Hg)
(Cd)
Chromium
Biphenyls
Diphenyl
(CR(VI))
(PBB)
Ethers
(PBDE)
Housing
O
O
O
O
O
O
Display
O
O
O
O
O
O
Printed Circuit
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Fan Assembly
O
O
O
O
O
O
Power Supply
O
O
O
O
O
O
O
O
O
O
O
O
Board
Metal
Fasteners
Cable
Assembly
Assemblies
Battery
O:
This toxic or hazardous substance is contained in all of the homogeneous materials for the part is
below the limit requirement in SJ/T11363-2006
X:
This toxic or hazardous substance is contained in at least one of the homogeneous materials for
this part is above the limit requirement in SJ/T11363-2006
Page 135
NANO-BT-i1 EPIC SBC
此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符
合中国 RoHS 标准规定的限量要求。
本产品上会附有”环境友好使用期限”的标签,此期限是估算这些物质”不会有泄漏或突变”的
年限。本产品可能包含有较短的环境友好使用期限的可替换元件,像是电池或灯管,这些元
件将会单独标示出来。
部件名称
有毒有害物质或元素
铅
汞
镉
六价铬
多溴联苯
多溴二苯
(Pb)
(Hg)
(Cd)
(CR(VI))
(PBB)
醚
(PBDE)
壳体
O
O
O
O
O
O
显示
O
O
O
O
O
O
印刷电路板
O
O
O
O
O
O
金属螺帽
O
O
O
O
O
O
电缆组装
O
O
O
O
O
O
风扇组装
O
O
O
O
O
O
电力供应组装
O
O
O
O
O
O
电池
O
O
O
O
O
O
O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
Page 136
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement