Digicharger D4
®
The All-Round Flashlight Expert
The Nitecore D4 is a universal smart charger compatible with almost all cylindrical
rechargeable batteries, thus eliminating the need to own several chargers. The D4
automatically detects Li-ion, Ni-MH and Ni-Cd batteries, and through manual selection is also
capable of charging LiFePO4 batteries. Intelligent charging circuitry selects the optimal
charging mode (CC, CV and dV/dt) for a given battery and each of the D4’s four
microcomputer-controlled charging slots then monitors and charges the battery
independently. Furthermore, an integrated digital LCD screen clearly displays charging
progress, voltage, current and time while an intelligent automatic power-off function
terminates current when charging is complete.
The Nitecore D4: The world’s most advanced fully-automatic digital charger. It’s as simple as
insert, detect and charge.
Features
• Capable of charging 4 batteries simultaneously
• Each of the four battery slots monitors and charges independently
• Compatible with and identifies Li-ion (26650, 22650, 18650, 17670, 18490, 17500, 18350,
16340(RCR123), 14500, 10440), Ni-MH and Ni-Cd (AA, AAA, AAAA, C) rechargeable
batteries
• Optimized charging design for IMR batteries
• Integrated LCD panel clearly displays charging parameters and progress
• Two conveniently located side buttons allow easy selection of specific battery types and
charging parameters
• Intelligent circuitry detects the battery type and status before entering automatic charge
mode (CC, CV, dV/dt)
• Automatically detects battery power status and selects the appropriate voltage and charge
mode (with the exception of LiFePO4 batteries which require manual selection)
• Compatible with LiFePO4 batteries
• Compatible with small capacity batteries
• Automatically stops charging when complete
• Features reverse polarity protection
• Designed for optimal heat dissipation
• Certified by RoHS, CE, FCC and CEC
• Insured worldwide by Ping An Insurance (Group) Company of China, Ltd.
Specifications
AC 100-240V 50/60Hz 0.35A(MAX), DC 12V 1A
4.2V ±1% / 3.7V ±1% / 1.48V ±1%
375mA x 4 / 750mA x 2
Compatible with:
Li-ion / IMR / LiFePO4: 26650, 22650, 18650, 17670, 18490, 17500, 18350, 16340(RCR123),
14500, 10440
Ni-MH / Ni-Cd:
AA, AAA, AAAA, C
Dimensions:
143mm× 99mm×36mm
Weight:
239g (without batteries and power cord)
Charging Small Capacity Batteries
When charging batteries with a capacity lower than 750mAH (e.g. AAA, 10440 and 16340
batteries), a low charging current is recommended to help extend battery life.
To select a low charging current, while in regular charging mode, simply press the side
“SLOT” button to select a desired battery slot and then press and hold the side “MODE”
button for more than 1 second until “LOW” is displayed on the LCD display indicating
activation of low current charging mode. To exit, simply press and hold the side “MODE”
button for more than 1 second once again or remove and reinstall the battery.
Nocturnal Charging Mode
When charging a battery overnight, nocturnal charging mode is recommended. Simply press
and hold the side “SLOT” button for more than 1 second in any state until the LCD backlight
turns off thus activating nocturnal charging mode. This feature ensures a peaceful night’s
sleep without being disturbed by the D4’s LCD backlight and blinking LEDs. To exit nocturnal
mode and turn the backlight on again, press and hold the side “SLOT” button for more than 1
second again.
Battery Activation
The D4 is capable of activating depleted Li-ion batteries with protective circuit. After battery
installation, D4 will test and activate the battery before charging. When a battery is detected
as damaged, the LCD displays Err, and D4 terminates its charging. Such damaged battery
cannot be activated by D4.
NOTE: Nitecore does not recommend charging 0V (depleted) unprotected Li-ion batteries
with D4 and doing so can result in battery fire or explosion.
Operating instructions
1. Plug one end of the power cord or car charging adapter into the D4 charger. Plug the other
end of the cord into an applicable outlet. The LCD display and all battery indicator bars will
illuminate as the charger runs a quick self-test. When testing is complete, the name of the
product will appear on the screen, the bars will dim and the charger will enter into stand-by
mode. If no batteries are detected within 1 minute, the charger will automatically enter Eco
Mode (the LCD backlight will turn off). When a battery is installed while in Eco Mode, simply
press any button to activate the LCD display.
2. The D4 features four charging slots, each of which charges and monitors a battery
independently. Rechargeable batteries of differing chemistries and voltages may be charged
simultaneously using either 1, 2, 3 or all 4 of the charging slots. When inserting a battery,
ensure the positive and negative ends correspond with the positive (+) and negative (-)
symbols on the charger. Incorrect installation will result in failure to initiate the charging
process.
Note: The D4 is capable of charging 3.7v Li-ion rechargeable cells, 1.2v, Ni-MH/Ni-Cd
rechargeable batteries and 3.2v LiFePO4 batteries. See above for description of battery
sizes.
3. When a battery is first inserted the D4 will run a short test causing the battery indicators
bars to illuminate in sequence from the bottom to the top. When the test is complete, the D4
will enter into charging mode. If any unusual circumstances have been detected, e.g. a
backward battery installation, the battery indicator bars will blink rapidly and “Err” will be
presented on the screen to urge an immediate removal of the battery.
Precautions
1. The D4 is compatible with batteries of varying sizes, therefore when charging certain
batteries (such as 26650 and AAA), manual adjustment of the battery’s position within the slot
is recommended, as to ensure solid contact is made between both sides of the battery and
the charging slot’s metal contact points.
2. The D4 is restricted to charging Li-ion, IMR, LiFePO4, Ni-MH/Ni-Cd rechargeable batteries
only. Never use the D4 with other types of batteries as this could result in battery explosion,
cracking or leaking, causing property damage and/or personal injury.
3. The D4 should only be used indoors or inside a motor vehicle and under no circumstances
should it be exposed to water, high humidity and low or high ambient temperatures.
4. Do not disassemble or modify the charger.
5. Children under the age of 18 should be supervised by an adult when using the D4.
6. The D4’s safe operating temperature is between 0-40ºC。
7. Do not use or store the charger near open flames, direct sunlight, heating devices or other
high-temperature environments.
Warranty Service
All NITECORE® products enjoy a comprehensive after sale warranty service. A
malfunctioning NITECORE® D4 charger may be exchanged for a replacement by a local
authorized distributor/dealer within the first 15 days of receipt by the end user. After 15 days
and up to 12 months, the D4 may be sent to an authorized distributor/dealer for repair.
Beyond 12 months, the warranty covers labor costs and maintenance with the exclusion of
accessories or replacement parts.
The warranty is nullified in any of the following situations:
1. The product(s) is/are broken down, reconstructed and/or modified under unauthorized
conditions.
2. The product(s) is/are damaged through improper use.
3. The product(s) is/are damaged by leakage of batteries.
For further details of Nitecore’s warranty service, please contact a regional distributor/dealer
or send an email to [email protected]
※All images, text and statements specified herein this user manual are for reference purpose
only. Should any discrepancy occurs between this manual and information specified on
www.nitecore.com, information on our official website shall prevail. Sysmax Industry Co., Ltd.
reserves the rights to interpret and amend the content of this document at any time without
prior notice.
4. While in charging mode, the battery indicator bars will blink rhythmically to indicate the
on-going charging process. The battery’s power status and charging progress is indicated by
the number of bars that illuminate steadily. The LCD display will also display battery voltage,
followed by charging current and elapsed charging time in sequence. Pressing the side
“MODE” button will cycle through these charging parameters. To view the charging progress
of a different charging slot press the side “SLOT” button to select a desired slot. When
charging is complete, all five battery indicator bars will illuminate steadily and “Chg.Finish”
will appear on the LCD display.
Validation code and QR code on package can be verified on Nitecore website.
Note: When the D4 is charging three or four batteries, charging current will be set to 375mA.
Alternatively, when charging either one or two batteries, charging current will be set to
750mA.
SYSMAX Industry Co., Ltd.
Charging LiFePO4 batteries
To charge LiFePO4 batteries, simply press and hold the side “MODE” button for more than 2
WARNING:THE D4 IS RESTRICTED TO CHARGING Li-ion, IMR, 3.7V LiFePO4, Ni-MH and
Ni-Cd RECHARGABLE BATTERIES ONLY. NEVER USE THE D4 FOR OTHER TYPES OF
BATTERIES AS THIS COULD RESULT IN BATTERY EXPLOSION, CRACKING OR LEAKAGE,
CAUSING PROPERTY DAMAGE AND/OR PERSONAL INJURY.
TEL:
FAX:
E-mail:
Web:
Address:
Please find us on facebook:
NITECORE Flashlights
+86-20-83862000
+86-20-83882723
[email protected]
www.nitecore.com
Rm1401-03, Glorious Tower, 850 East Dongfeng Road,
Guangzhou, China 510600
Thanks for purchasing NITECORE!
201501023
• Made from durable ABS (fire retardant / flame resistant)
Output current:
seconds right after the battery test completes and “LiFePO4” will appear on the LCD display
to indicate the activation of LiFePO4 charging mode. To exit LiFePO4 charging mode, simply
press and hold the side “MODE” for more than 2 seconds once again, or remove and reinstall
the battery.
The D4 is equipped with an advanced ‘overtime’ safety function. The D4 will individually
monitor the elapsed charging time for each battery slot and if a particular slot exceeds 20
hours, the D4 will automatically power off the slot and display full charging bars to indicate
completion of the charging process. This feature reduces the risk caused by batteries of
lesser quality.
• Features temperature monitoring to prevent overheating
Output voltage:
User Manual
Overtime Prevention
• Features over-charge prevention to protect batteries
Input:
Digicharger D4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement