- Scantime.co.uk
CX-Supervisor
User Manual
Software Release 1.2
OMRON
CX-Supervisor – User Manual
Notice
OMRON products are manufactured for use according to proper procedures by a qualified operator
and only for the purposes described in this manual.
The following conventions are used to indicate and classify precautions in this manual. Always heed
the information provided in them. Failure to heed precautions can result in injury to people or
damage to the product.
DANGER!
Indicates information that, if not heeded, is likely to result in loss of life or
serious injury.
WARNING
Indicates information that, if not heeded, could possibly result in loss of
life or serious injury.
Caution
Indicates information that, if not heeded, could result in relatively serious
or minor injury, damage to the product, or faulty operation.
OMRON Product References
All OMRON products are capitalised in this manual. The word “Unit” is also capitalised when it
refers to an OMRON product, regardless of whether or not it appears in the proper name of the
product.
The abbreviation “PLC” means Programmable Logic Controller and is not used as an abbreviation
for anything else.
Revision 1.2
Page i
CX-Supervisor – User Manual
Page ii
OMRON
Revision 1.2
OMRON
CX-Supervisor – User Manual
Visual Aids
The following headings appear in the left column of the manual to help you locate different types of
information.
Note:
Indicates information of particular interest for efficient and convenient
operation of the product.
1, 2, 3…
Indicates lists of one sort or another, such as procedures, checklists etc.
Represents a shortcut on the Toolbar to one of the options available on the
menu of the same window.
Indicates a program must be started, usually by clicking the appropriate
option under the standard Windows ‘Start’ button.
 OMRON, 2003
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form, or by any means, mechanical, electronic, photocopying, recording, or
otherwise, without the prior written permission of OMRON.
All copyright and trademarks acknowledged.
No patent liability is assumed with respect to the use of the information contained herein. Moreover,
because OMRON is constantly striving to improve its high-quality products, the information
contained in this manual is subject to change without notice. Every precaution has been taken in the
preparation of this manual. Nevertheless, OMRON assumes no responsibility for errors or omissions.
Neither is any liability assumed for damages resulting from the use of the information contained in
this publication.
Revision 1.2
Page iii
CX-Supervisor – User Manual
Page iv
OMRON
Revision 1.2
OMRON
CX-Supervisor – User Manual
About this Manual
This manual describes the CX-Supervisor application and its ability to create, modify and run
SCADA applications.
This manual contains the following:
Chapter 1 - Graphics Editor. This chapter describes the Graphics Editor and its various tools and
controls.
Chapter 2 - Pages. This chapter describes the procedures involved in the creation and amendment of
pages.
Chapter 3 - Points. This chapter describes the procedures involved in the creation, amendment and
removal of points. The use of PLCs with points is also described.
Chapter 4 - Objects. This chapter describes procedures involved in the creation, amendment and
removal of objects.
Chapter 5 - ActiveX Objects. This chapter provides an overview of using ActiveX objects in CXSupervisor.
Chapter 6 - Projects. This chapter describes procedures involved in the creation, amendment and
removal of projects.
Chapter 7 - Graphics Library. This chapter describes the library of graphic objects and how to
create and amend new libraries.
Chapter 8 - Alarms. This chapter describes the procedures involved in the creation and amendment
of alarms.
Chapter 9 - Animation. This chapter describes the use of animations and how they can be applied to
a CX-Supervisor project.
Chapter 10 - Recipes. This chapter describes the creation of recipes, and how they can be used.
Chapter 11 - Data Logging. This chapter describes the data logging facilities, including setting up,
viewing and exporting
Chapter 12 - Databases. This chapter describes the Database facilities, including connections reading
and writing data.
Chapter 13 - Multilingual Features. This chapter describes the Multilingual features, including
creation of dynamically switching applications.
Chapter 14 - OPC Client. This chapter introduces OPC Server to a new user, and explains how to use
CX-Supervisor as an OPC Client
Revision 1.2
Page v
CX-Supervisor – User Manual
OMRON
Chapter 15 - Connecting to a Remote CX-Supervisor application. This chapter explains how to
create a distributed solution by connecting together CX-Supervisor applications on networked
PCs.
Chapter 16 - Connecting to Omron Industrial Components. This chapter details connecting CXSupervisor to Omron's Industrial Components.
Appendix A – Configuring a PC for remote connection. The appendix explains how to configure a
PC for remote connection.
Appendix B – Obsolete Features.
compatibility only.
The appendix details obsolete features for backwards
A Glossary of Terms and Index are also provided.
Page vi
Revision 1.2
OMRON
CX-Supervisor – User Manual
TABLE OF CONTENTS
CX-Supervisor ..................................................................................................Page
Chapter 1 - Graphics Editor.......................................................... 1
About the Graphics Editor ...................................................................................... 1
Palette .................................................................................................................... 1
Graphic Object Bar ................................................................................................. 4
Control Bar ............................................................................................................. 4
Status Bar............................................................................................................... 8
Text Bar .................................................................................................................. 9
Grid....................................................................................................................... 11
Chapter 2 - Pages.......................................................................... 13
Creating a Page.................................................................................................... 13
Amending a Page................................................................................................. 14
Defining the Properties of a Page ........................................................................ 14
Printing a Page ..................................................................................................... 16
Saving a Page to a Project................................................................................... 20
CX-Supervisor Preferences.................................................................................. 20
Chapter 3 - Points......................................................................... 23
What is a Point? ................................................................................................... 23
About the Point Editor .......................................................................................... 23
Viewing Points via the Point Editor....................................................................... 24
Creating a Point.................................................................................................... 27
Amending an Existing Point ................................................................................. 33
Deleting an Existing Point .................................................................................... 34
Quick creation of many points .............................................................................. 35
Runtime Point Maintenance ................................................................................. 36
Point Import ......................................................................................................... 37
System Points....................................................................................................... 38
Revision 1.2
Page vii
CX-Supervisor – User Manual
Page viii
OMRON
Revision 1.2
OMRON
CX-Supervisor – User Manual
Table of Contents section 3 continued
Page
Printing Points ...................................................................................................... 41
Chapter 4 - Objects ...................................................................... 43
Objects ................................................................................................................. 43
Editing Objects ..................................................................................................... 43
Creating and Editing Graphic Objects .................................................................. 44
Creating and Editing Control Objects ................................................................... 46
Manipulating Objects............................................................................................ 61
Chapter 5 – ActiveX Objects ....................................................... 67
Overview............................................................................................................... 67
Inserting a new object .......................................................................................... 67
Editing Properties at Design Time........................................................................ 68
Reading and Writing Properties at Run Time....................................................... 70
Calling Methods at Runt Time .............................................................................. 70
Responding to Events .......................................................................................... 70
Chapter 6 - Projects...................................................................... 73
Overview............................................................................................................... 73
Creating a Project................................................................................................. 73
Amending a Project .............................................................................................. 74
Saving a Project ................................................................................................... 74
Printing a Project .................................................................................................. 75
Device Configuration ............................................................................................ 75
Settings................................................................................................................. 81
Runtime Security .................................................................................................. 91
Exit Level .............................................................................................................. 94
Compiling and Running a Project......................................................................... 95
Save Runtime As.................................................................................................. 95
Create Runtime Install Disc.................................................................................. 95
Project Information ............................................................................................... 95
Alias Definitions .................................................................................................... 96
Revision 1.2
Page ix
CX-Supervisor – User Manual
Page x
OMRON
Revision 1.2
OMRON
CX-Supervisor – User Manual
Table of Contents section 6 continued
Page
Find....................................................................................................................... 96
Navigating Projects with the Workspace.............................................................. 98
Project Editor ........................................................................................................ 98
Printing from the Project Editor .......................................................................... 101
Chapter 7 - Graphics Library ................................................... 103
Overview............................................................................................................. 103
Graphics Library ................................................................................................. 103
Manipulating Objects.......................................................................................... 105
Printing the Graphics Library.............................................................................. 107
Chapter 8 - Alarms ..................................................................... 109
What is an Alarm? .............................................................................................. 109
Alarm Settings .................................................................................................... 109
Viewing the Contents of the Alarm Database .................................................... 111
Creating a New Alarm ........................................................................................ 112
Updating an Existing Alarm ................................................................................ 116
Copying an Existing Alarm Definition ................................................................. 117
Deleting an Existing Alarm ................................................................................. 117
Printing Alarms ................................................................................................... 117
Alarm Reporting In Runtime ............................................................................... 118
Chapter 9 - Animation ............................................................... 121
Associating Points with Actions and Events....................................................... 121
Animation Editor ................................................................................................. 121
Runtime Actions ................................................................................................. 127
Chapter 10 - Recipes .................................................................. 155
What is a Recipe? .............................................................................................. 155
Recipe Components ........................................................................................... 155
Viewing Recipes in the Recipe Editor ................................................................ 156
Creating a New Recipe ...................................................................................... 157
Revision 1.2
Page xi
CX-Supervisor – User Manual
Page xii
OMRON
Revision 1.2
OMRON
CX-Supervisor – User Manual
Table of Contents section 10 continued
Page
Updating an Existing Recipe .............................................................................. 160
Copying an Existing Recipe Definition ............................................................... 162
Deleting an Existing Recipe ............................................................................... 162
Recipe Security Levels....................................................................................... 162
Printing Recipes ................................................................................................. 163
Using Recipes in Runtime .................................................................................. 164
Chapter 11 - Data Logging ........................................................ 169
What is Data Logging? ....................................................................................... 169
Data Log Editor................................................................................................... 169
Data Logging at Runtime................................................................................... 174
Data Log View Component ................................................................................ 178
Remote Data Log Viewer ................................................................................... 179
Data Log Export Facilities .................................................................................. 180
Data Logging ...................................................................................................... 182
Chapter 12 - Databases .............................................................. 187
Overview............................................................................................................. 187
Database Connection Editor .............................................................................. 187
Configuring a connection.................................................................................... 188
Configuring Recordsets...................................................................................... 195
Configuring Field Associations ........................................................................... 197
Configuring Parameter Associations .................................................................. 199
Configuring Schemas ......................................................................................... 200
Using Transactions............................................................................................. 204
Saving Recordsets as XML ................................................................................ 205
Datashaping ....................................................................................................... 205
Revision 1.2
Page xiii
CX-Supervisor – User Manual
Page xiv
OMRON
Revision 1.2
OMRON
CX-Supervisor – User Manual
Table of Contents section 12 continued
Page
Chapter 13 – Multilingual features........................................... 211
Development Features ....................................................................................... 211
Runtime Multilingual Features............................................................................ 237
Chapter 14 – Using CX-Supervisor as an OPC Server .......... 217
What is OPC....................................................................................................... 217
Using CX-Supervisor with Omrons OPC Server ................................................ 217
Using the Third Party OPC Servers ................................................................... 222
Chapter 15 – Connecting to Remote Applications .................. 223
Two Tier, Client-Server or Master-Slave? .......................................................... 223
Peer to Peer ....................................................................................................... 224
Distributed Server............................................................................................... 224
Redundant Server .............................................................................................. 225
Creating a CX-Supervisor Server application .................................................... 225
Creating a CX-Supervisor Client application...................................................... 226
Chapter 16 – Connecting to Omron Industrial Components 229
Adding a Point linked to a parameter ................................................................. 229
Appendix A – Configuring a PC for remote connection ........ 233
Configurating a Client PC running Windows NT or 2000 ................................... 233
Configurating a Client PC running Windows XP ................................................ 233
Configurating a Client PC running Windows 98 or Me....................................... 233
Configurating a Server PC running Windows NT or 2000.................................. 234
Configurating a Server PC running Windows XP............................................... 234
Configurating a Server PC running Windows 98 or Me ..................................... 254
Appendix B – Obsolete Features............................................... 237
Glossary of Terms....................................................................... 252
Index ............................................................................................ 260
Revision 1.2
Page xv
OMRON
CHAPTER 1 – Graphics Editor
CHAPTER 1
Graphics Editor
This chapter describes the Graphics Editor and the various tools and controls available. It also
provides instructions for using these tools and controls and is supported with suitable screen displays.
About the Graphics Editor
The Graphics Editor enables a variety of objects to be created on a page. Supported objects are:
♦
Graphical objects.
♦
Control objects.
♦
ActiveX objects.
Graphical objects are geometric shapes, for example ellipses and polygons, but also include Text
objects. Control objects allow information to be displayed and entered in clear way through the use
of Wizards. Examples of control objects include Pushbuttons and Trend Graphs. ActiveX objects or
controls are from sources external to CX-Supervisor.
Refer to chapter 4, Objects for further information regarding control objects and bitmap objects.
Refer to chapter 5 for further information on ActiveX Objects.
The tools are contained on a Control Bar, and within palettes. The palettes allow all similar types of
tool to be kept together, and are contained within a free floating window. The various tools and
palettes are discussed in the following chapters. Status and help information is presented in a Status
Bar located at the bottom of the main CX-Supervisor window.
Palette
The Palette is always displayed on top of any pages created within CX-Supervisor. If no pages are
open, the Palette is not displayed, and if there are no currently active pages, the Palette is rendered
inactive. An example of the Palette illustrating the position of various palettes and controls is shown
below:
Revision 1.2
Page 1
CHAPTER 1 – Graphics Editor
OMRON
The Palette can be removed or re-displayed at any time by selecting Palette from the View menu.
A tick next to the name indicates the Palette is currently displayed. CX-Supervisor saves the settings
when it is exited and restores them when it is next run.
Each of the palettes and controls is discussed in more detail in the following paragraphs.
Colour Palette
To create an object in a particular colour: before selecting the object’s tool from the Graphic Object
bar, first select the colour by clicking in the appropriate square in the Colour Palette.
Note:
It is not strictly necessary to select a colour for an object before creating it, however
if no colour selection is made, the object retains the same colour as the last object.
To apply a colour to a previously created object, select the object on the page and click with the left
mouse button in the appropriate square in the Colour Palette.
Note:
Colour may only be applied to some graphic objects. It cannot be applied to
embedded objects or bitmap graphics.
Line Style Palette
The Line Style Palette is located in the Palette just below the Colour Palette.
To create an object with a particular line style: before selecting the object from the Tool Palette, first
select the line style by clicking on the appropriate line in the Line Style Palette.
Note:
It is not strictly necessary to select a line style for an object before creating it,
however if no line style selection is made, the object retains the default style of thin
solid.
To apply a line style to a previously created object, select the object on the page and click on the
appropriate line in the Line Style Palette.
Note:
Page 2
Line styles may only be applied to some graphic objects. They cannot be applied to
text, embedded objects, controls or bitmap graphics.
Revision 1.2
OMRON
CHAPTER 1 – Graphics Editor
Fill Pattern Palette
The Fill Pattern Palette is located at the bottom of the Palette.
To create an object with a particular fill pattern: before selecting the object’s tool from the Tool
Palette, first select the fill pattern by clicking in the appropriate square in the Fill Pattern Palette.
Note:
It is not strictly necessary to select a fill pattern for an object before creating it,
however if no fill pattern selection is made, the object retains the default of no
pattern.
To apply a fill pattern to a previously created object, select the object on the page and click in the
appropriate square in the Fill Pattern Palette. With a fill pattern applied to an object, clicking in the
Colour Palette with the left mouse button allows the foreground colour of the chosen fill pattern to be
changed. Clicking in the Colour Palette with the right mouse button allows the background colour of
the chosen fill pattern to be changed.
Note:
Fill patterns may only be applied to solid graphic objects. They cannot be applied
to unfilled graphic objects, text objects, embedded objects, controls or bitmap
graphics.
Extended Colour, Line Style and Fill Pattern Palette
Each of the Colour, Line Style and Fill Pattern Palettes may be extended to allow access to more
choices. Only one palette may be extended at any one time. The Extended Selection tools are
located at the top of the Palette and are illustrated as follows:
The left hand square controls the extension of the Colour Palette; the line between the two squares
controls the Line Style Palette extension, and the right hand square control the Fill Pattern Palette
extension.
An example of the Extended Colour, Line Style, and Fill Pattern Palettes is shown below:
The operation of each of the extended palettes is identical to that of the non-extended palettes.
Revision 1.2
Page 3
CHAPTER 1 – Graphics Editor
OMRON
Graphic Object bar
The Graphic Object bar contains the tools to create the graphic objects which can be placed on pages
within CX-Supervisor.
In general terms, the operation of the Graphic Object bar is simple. With a page active the Graphic
Object bar is active, and operation involves merely clicking on the desired tool to select it, and then
clicking and dragging to the appropriate point in the page. This is not the case with the text, polygon
or polyline tools, however the operation of these tools is fully discussed in chapter 4, Objects.
Moving the mouse pointer over any of the tools causes CX-Supervisor to display a tooltip to describe
the tool.
By default, the cursor returns to Selection mode (an arrow) after drawing an object. If you would
prefer it to remain in its current state, clear the Return to select mode checkbox in the Editing
Preferences dialog, which is found on the CX-Supervisor file menu.
For further details concerning the tools contained within the Graphic Object bar refer to chapter 4,
Objects.
Control Bar
CX-Supervisor provides a Control Bar containing formatting and object manipulation tools. The
Control Bar can be activated or de-activated from the View menu. To activate the Control Bar, select
Control Bar from the View menu; CX-Supervisor places a check mark next to it signifying its active
status. To de-activate it, repeat the procedure (the check mark is removed), and the Control Bar is no
longer displayed. The various tools on the control bar allow the properties of objects to be modified.
A control may be activated with more than one object selected to change a particular attribute of all
of the selected objects, e.g. when all graphical objects on a page are selected and the Rotate button is
pushed in and the desired angle specified, all selected objects are rotated.
An illustration of the Control Bar is as follows:
The Control Bar may vary slightly from this according to the display resolution currently in use - the
number of buttons displayed depends on the available space - at higher resolutions more buttons are
displayed.
The Control Bar can be removed from the display at any time by selecting Control Bar from the View
menu.
Page 4
Revision 1.2
OMRON
CHAPTER 1 – Graphics Editor
A tick next to the name indicates that it is currently displayed. CX-Supervisor saves the settings
when it is exited and restores them when it is next run.
The specific operation of the controls on the Control Bar is described in the following paragraphs.
Object Identification
When an object is created, CX-Supervisor gives it a unique identifier. This identifier consists of the
object type and a sequential number (starting at 1). For example, a text object could have an
identifier of TEXT_1; a polygon object could have an identifier of POLYGON_3 etc. The Object
Identification field displays a list of all current objects on a page.
The identification of an object can be changed by clicking on the entry in the Object Identification
control, typing over the entry and pressing <Return>. A confirmation box is provided to double
check the operation, click the OK pushbutton to proceed with the name change or the Cancel
pushbutton to abort the operation.
It can at times be difficult to select a particular object if it is mostly obscured by other graphic
objects. The Object Identification control allows an object to be selected by simply selecting its
name from the presented list. Click on the arrow button to display the list and select the desired
object. On selection the object is highlighted.
The following illustration shows the Object Identification control in de-selected state:
The following illustration shows the Object Identification control in selected state:
Raise Up One
The Raise Up One button allows an object which forms part of an overlapping group of
objects to be moved nearer the top of the group, one layer at a time. With an object selected,
clicking the pushbutton once moves the object up one layer. This continues until the object
is at the top. Clicking the pushbutton with the object at the top of a group has no effect.
The following example illustrates the state of a group of two objects before and after clicking the
Raise Up One button with the black round rectangle selected:
Revision 1.2
Page 5
CHAPTER 1 – Graphics Editor
OMRON
Before
After
Lower Down One
The Lower Down One button allows an object which forms part of an overlapping group of
objects to be moved nearer the bottom of the group, one layer at a time. With an object
selected, clicking the button once moves the object down one layer. This continues until the
object is at the bottom. Clicking the button with the object at the bottom of a group has no
effect.
The following example illustrates the state of a group of two objects before and after clicking the
Lower Down One button with the grey polygon selected:
Before
After
Rotate
The Rotate button allows graphical and bitmap objects to be rotated. With an object
selected, clicking the button once opens the Rotate dialog box. Set the desired angle and
click the OK pushbutton to rotate the object.
The following example illustrates the state of an object before and after clicking the Rotate button
and defining a 10° rotation with the object selected:
Page 6
Revision 1.2
OMRON
CHAPTER 1 – Graphics Editor
Before
Rotated 10°°
Horizontal Mirror
The Mirror Horizontal button on the Control Bar allows graphical and bitmap objects to be
mirrored in the horizontal plane. With an object selected, clicking the button once “flips” the
object producing a horizontal mirror image.
The following example illustrates the state of an object before and after clicking the Mirror
Horizontal button with the object selected:
Before
After
Vertical Mirror
The Mirror Vertical button allows graphical and bitmap objects to be mirrored in the
vertical plane. With an object selected, clicking the button once “flips” the object producing
a vertical mirror image.
The following example illustrates the state of an object before and after clicking the Mirror Vertical
button with the object selected:
Before
After
Transparency On/Off
The Transparency button changes an object from solid to outline and from outline to solid.
With an object selected, click the button and the object toggles from solid to outline (or
vice-versa).
Revision 1.2
Page 7
CHAPTER 1 – Graphics Editor
OMRON
The following example illustrates the state of an object before and after clicking the Transparency
button with the object selected:
Before
After
Status Bar
CX-Supervisor provides help and status information in a Status Bar located at the bottom of the main
window.
The Status Bar has two main active areas: the Help Message area, and the Cursor Co-ordinates area.
The Help Message area is used by CX-Supervisor to display helpful information concerning menu
selections and controls. It is located at the left hand end of the Status Bar, and can display messages
similar to the following:
The Cursor Co-ordinates area provides position information for the current location of the mouse
pointer as it tracks around the active page within the CX-Supervisor window. If an object on a page
is selected, the status area displays the co-ordinates of the location of that object. An example of the
system status area is illustrated as follows:
Page 8
Revision 1.2
OMRON
CHAPTER 1 – Graphics Editor
The first two display panels show the current x and y co-ordinates of the mouse pointer within the
currently active page. As the mouse pointer leaves the confines of a page and moves into the client
area of the main CX-Supervisor window, the last recorded co-ordinates are held in these panels.
If an object is clicked on, all four panels are used by CX-Supervisor to display the co-ordinates of
that object, as follows:
x
y Width Height
The first two panels contain the distance of the top left corner of the object from the top left of the
page in pixels. The second two panels show the extent of the object in pixels.
Text Bar
An illustration of the CX-Supervisor Text Bar is as follows:
Font Name
The Font Name field contains a list of fonts which are available on the host version of Windows. The
list is presented in alphabetical order, and only details typeface families. This does not include bold
or italic variants as this attribute is set by using the appropriate button.
The following illustration shows the control in de-selected state:
The following illustration shows the control in selected state:
Revision 1.2
Page 9
CHAPTER 1 – Graphics Editor
OMRON
The Font Name field displays the current font attribute for the selected object(s). To change the font
for a block of text, highlight it and click either: the down arrow adjacent to the edit part of the
control, or into the edit part of the control itself, for the Font Name field. The control then displays a
list of available fonts, from which the desired typeface may be selected.
If more than one block of text is selected with each having different font attributes, the edit part of the
control is empty. However, selecting a font from the supplied list still sets the font attribute for all
the selected group of text blocks.
Fonts and font families are printer dependent, therefore changing the printer within the Printer Setup
dialog (accessed from the File menu) changes the fonts which are available within the Font Name
field.
Font Size
The Font Size field contains a list of point sizes available on the host version of Windows for the
selected font. The list is presented in numerical order.
The following illustration shows the control in de-selected state:
The following illustration shows the control in selected state:
Either click the cursor into the editable area of the control and enter a new point size, or click the
down arrow and select a new point size from the presented list.
The control displays the current point size for the selected block of text. If more than one block of
text is selected having different point sizes, the edit part of the control is empty. However, selecting a
font from the supplied list (or typing in a new point size) still sets the point size for all the selected
blocks of text.
Page 10
Revision 1.2
OMRON
CHAPTER 1 – Graphics Editor
Text Bold On/Off
The Text Bold button allows any selected text objects to be set to bold when the Text Bold
button is pushed in, or normal when the Text Bold button is released. Text Bold only
applies to text, block text, and to text on buttons, other controls and graphics cannot be
emboldened.
Text Italic On/Off
The Text Italic button allows any selected text object(s) to be set to italic when the Text
Italic button is pushed in, or normal when the Text Italic button is released. Text Italic only
applies to text, block text, and to text on buttons, other controls and graphics cannot be
italicised.
Text Underline On/Off
The Text Underline button allows any selected text object(s) to be set to underline when the
Text Underline button is pushed in, or normal when the Text Underline button is released.
Text Underline only applies to text, block text, and to text on buttons, other controls and
graphics cannot be underlined.
Text Left Aligned
The Text Left Aligned button aligns any selected text object(s) to the left edge of the
bounding box. Text Left Justified only applies to text, block text, and to text on buttons,
other controls and graphics cannot be left justified.
Text Centred
The Text Centred button aligns any selected text object(s) to the centre of the bounding
box. Text Centre Justified only applies to text, block text, and to text on buttons, other
controls and graphics cannot be centre justified.
Text Right Aligned
The Text Right Aligned button aligns any selected text object(s) to the right edge of the
bounding box. Text Right Justified only applies to text, block text, and to text on buttons,
other controls and graphics cannot be right justified.
Grid
The use of the grid may be helpful in drawing and aligning the objects on the screen. Select
the Grid button from the toolbar to enable the grid.
The grid settings are available by selecting Grid from the View menu. All the available grid sizes are
shown along with a Snap to Grid option which forces graphical objects selected by the user to align
according to the current grid setting.
Revision 1.2
Page 11
CHAPTER 1 – Graphics Editor
Page 12
OMRON
Revision 1.2
OMRON
CHAPTER 2 – Pages
CHAPTER 2
Pages
This chapter explains the concept of pages. The chapter covers creating, amending, printing and
saving pages.
Creating a Page
A project may consist of several pages, but must contain at least one.
To create a new page, CX-Supervisor must currently have a project open. If no project is currently
open, either click on the Open button from the toolbar to open a previously saved project, or select
New from the Project menu to create a new project.
Note:
When you first create a project, CX-Supervisor creates a new page for you
automatically. For more details concerning projects, refer to chapter 6, Projects.
With a project open, click the New Page button from the toolbar to create a new blank page.
An example of a new blank page is shown as follows:
Release 1.2
Page 13
CHAPTER 2 – Pages
OMRON
Amending a Page
To amend a page, it must first be open. If no pages are open click the Open Page button
from the toolbar. A standard File Open dialog with the caption Open Page is displayed. The
layout and usage depends on your operating system so see your Microsoft documentation for
details.
1, 2, 3…
Note:
1.
Locate the drive and directory where the desired page is stored.
2.
Select the desired page from the list presented.
3.
Click the Open pushbutton to load the page.
Loading a page does not automatically make it part of a project. It is therefore
perfectly feasible to load and edit pages from other projects. Use the Project Editor
to attach a page to a project. For more details concerning projects, refer to chapter
6, Projects.
The loaded page may now be edited as required using the CX-Supervisor editing tools.
Defining the Properties of a Page
A page has certain attributes, or properties. These properties may be viewed and edited in two ways.
The simplest way to access the properties of a page is to double click with the left mouse button in
the background area of the page.
This causes CX-Supervisor to display the following Page Properties dialog:
The Page Properties dialog allows the viewing and editing of various attributes.
Page 14
Release 1.2
OMRON
CHAPTER 2 – Pages
1, 2, 3…
Release 1.2
1.
Enter a title for the page in the Page Title: field up to a maximum of 32
characters.
2.
Add a description (if required) in the Page Description field.
3.
Enter the co-ordinates for the top-left corner of the page in the Top and Left
field. This value must be in pixels, and must be a positive integer between
0 and 2000. Alternatively, click on the Full Size pushbutton to fill the
runtime environment workspace.
4.
Enter the height and width measurements for the page in the Height and
Width fields. These values must be in pixels, and must be a positive integer
between 0 and 2000. Click on the Centre pushbutton to centre the page to
the graphics workspace.
5.
Select the border style for the page from the Border Style settings. The
default for this is Sizeable, as shown on the Page Properties dialog.
Changing the selection will update the shown preview.
6.
To prevent the title from being displayed, click the Display Title setting to
remove the check mark. The following change occurs in the dialog:
7.
To change the display mode, select Overlap, Replace or Popup in the
Display Mode setting. ‘Popup’ pages appear above all other page types,
‘Overlap’ pages can lie on top of other pages, and ‘Replace’ pages closes
any pages that overlap.
8.
To alter the colour of the page, click in the Demo Page Window area or
click on the Colour pushbutton. CX-Supervisor displays the Colour Palette
dialog:
Page 15
CHAPTER 2 – Pages
OMRON
9.
Either select a colour from the palette area or click on a palette colour and
edit it using the three colour sliders. When the desired colour is displayed,
click the OK pushbutton to return to the Page Properties dialog.
10. Alternatively, to display an image or photograph as the background click the
Background pushbutton and select the desired file and note the Display
Background check box is automatically ticked.
Printing a Page
Print Setup
Before printing a page, ensure that the printer has been set up correctly. To check the printer settings,
select Print Setup from the File menu.
CX-Supervisor displays the Print Setup dialog in response:
Page 16
Release 1.2
OMRON
CHAPTER 2 – Pages
The current printer selection is defined in the Name: control box. To alter the settings, proceed as
follows:
1, 2, 3…
Note:
1.
To change the current printer selection, click the Name: field and select
from the list presented.
2.
To change the page orientation from portrait to landscape click the
Landscape setting, (or vice-versa).
3.
To change the paper size, click the Size: field, and select the desired paper
size from the list presented.
4.
To change the paper source, click the Source: field, and select the desired
paper source from the list presented.
5.
Click the OK pushbutton to exit from the Print Setup dialog when the
settings are correct.
The Properties pushbutton gives access to advanced printer configuration
functions for the selected printer. For details of these functions, refer to the
Windows User Manual, On-line Help, or the appropriate Manufacturer’s
handbook.
Print Preview
To preview the page before printing, select Print Preview from the File menu.
This results in a screen display similar to the following:
Release 1.2
Page 17
CHAPTER 2 – Pages
1, 2, 3…
OMRON
1.
To print the page, click the Print pushbutton, CX-Supervisor displays the
Print dialog.
2.
To display the next page, click the Next Page pushbutton.
3.
To display the previous page, click the Prev Page pushbutton.
4.
To display the current page, side-by-side with the next page, click the Two
Page pushbutton. To return to a single page view click the same button
again which now carries the legend, One Page.
5.
Click the Zoom In pushbutton. Click it a second time to zoom in to the
second level. This does not zoom into a specific area of the page.
6.
To zoom out from a zoomed in view, click the Zoom Out pushbutton.
Click a second time to zoom right out.
7.
To close the preview screen, click the Close pushbutton.
Printing
To print a page, click the Print Page button from the toolbar. The Print dialog is displayed.
Page 18
Release 1.2
OMRON
CHAPTER 2 – Pages
1, 2, 3…
Note:
Release 1.2
1.
Set the print range by clicking one of the settings in the Print range
settings. The Selection setting is only enabled when an item (or items) are
selected on the page prior to starting the print process. Click the Pages
setting and enter a range of pages in the from and to fields.
2.
To change the number of copies to be printed, enter a new value in the
Copies field.
3.
If multiple copies are selected, click the Collate setting to instruct the
printer to collate the copies as they are printed.
4.
To print to file, click the Print to file setting.
5.
Click the OK pushbutton to activate printing. Whilst printing is in
progress, a dialog is displayed showing the status of the print job. Clicking
the Cancel pushbutton at this point aborts the printing. Once printed, the
dialog disappears. The final printed version should be similar to that shown
in the Print Preview dialog, with a header describing the project, and a
footer describing the page with a page number and date stamp.
The Properties pushbutton on the Print dialog gives access to advanced printer
configuration functions for the selected printer. For details of these functions,
please consult the Windows User Manual, On-line Help, or the appropriate
Manufacturer’s handbook.
Page 19
CHAPTER 2 – Pages
OMRON
Saving a Page to a Project
Once a page has been created it is wise to save it into the project in which it is planned to reside. It is
good practice to ensure that pages are saved regularly, for example to minimise the loss of work in
the event of a power failure.
To save a page click the Save Page button from the toolbar. If this is the first time the page
has been saved, the Save As dialog is displayed. This is a standard Windows dialog and
usage depends on your operating system. Please consult your Microsoft documentation.
1, 2, 3…
1.
Move to the location where the page file is to be stored.
2.
Ensure that the Save as Type: control is set to CX-Supervisor Pages
(*.PAG).
3.
Enter a name in the File Name: field.
4.
Click the Save pushbutton to save the file.
Subsequent saves do not cause the Save As dialog to be displayed.
After clicking the Save pushbutton, if the page is currently not assigned to a project, a confirmation
dialog is displayed. Alternatively, select Save Page from the File menu (or use the short-cut key
combination of <Ctrl>+S.
Save Page As
Should a copy of a page be required, (for incorporation into another project perhaps), select Save
Page As... from the File menu.
CX-Supervisor displays the File Save As dialog as described previously. After entering a new name
for the page, CX-Supervisor prompts to save the different page into the current project as above.
Closing a Page
To close a page after editing select Close Page from the File menu.
Alternatively, either click on the control box for the page, (located in the top left corner of the page)
and select Close from the Control menu, or simply double-click on the Control menu and the page
closes.
Should you attempt to close a page which has not been saved, CX-Supervisor displays a confirmation
dialog. If you want to save the changes, click the Yes pushbutton. Otherwise, click the No
pushbutton, or click the Cancel pushbutton to abort closing the page.
CX-Supervisor Preferences
CX-Supervisor allows a user to customise the working environment. To set or amend the CXSupervisor setup, select Preferences from the File menu, followed by the preference to set up.
Page 20
Release 1.2
OMRON
CHAPTER 2 – Pages
The types of customisation are described in the following paragraphs.
Startup Preferences
The Startup Preferences allows the project last accessed in the previous session of CX-Supervisor to
be automatically loaded in the next session. It is accessible by selecting Startup from the Preferences
menu. Click in the Load last project on startup setting to switch this preference as desired. Click the
OK pushbutton to accept the change, or Cancel to abort.
Editing Preferences
The Editing Preferences dialog provides a number of switches to enhance the use of the Graphics
Editor and CX-Supervisor animation. It is accessed by selecting Editing from the Preferences menu.
The number of undo operations in the Graphics Editor can be set in the Number of Available ‘Undo’
Operations: field. To make the Graphics Editor return to Select Mode after every drawing operation,
click in the Revert to ‘Select Mode’ after Drawing Operations setting. The use of double-clicking on
an object can be defined: when a check mark is present in the Enter Edit Mode field, a double-click
on an object of that type causes it to enter Edit Mode.
When a check mark is present in a Display Animation Editor field, a double-click on an object of that
type activates the Animation Editor. Click the OK pushbutton to accept the changes, or the Cancel
pushbutton to abort.
Release 1.2
Page 21
CHAPTER 2 – Pages
OMRON
General Preferences
General Preferences allow the default script language to be chosen. When new scripts are added, CXSupervisor will default to saving scripts in the select language.
Page 22
Release 1.2
OMRON
CHAPTER 3 – Points
CHAPTER 3
Points
This chapter describes CX-Supervisor points and the procedures associated with the creation,
amendment and removal of points using the Points Editing facility. The application of external
sources to points is also described.
What is a Point?
A point is a variable used internally by CX-Supervisor. All points within CX-Supervisor have a
name, group and type associated with them.
CX-Supervisor provides a set of pre-defined System ($) Points, which are detailed in chapter 3
Points.
About the Point Editor
The Point Editor allows the viewing, creating, modifying and removing of points from the points
database.
Note:
System Points cannot be modified.
To open the Point Editor dialog, select the Point Editor button from the toolbar.
An example of the Point Editor dialog is as follows:
The typeface of the editor can be amended by selecting Preferences from the File menu. This is
especially useful when printing.
Note:
Release 1.2
To select a range of points, click on a point to mark the start of the range and click
again with the <Shift> key down to mark the end.
Page 23
CHAPTER 3 – Points
OMRON
Note:
To individually select more than one point, click whilst holding the <Ctrl> key
down.
Note:
The short-cut keyboard combinations for Cut, Copy and Paste operations are valid
within the Point Editor. Highlight one or more points and type <Ctrl>+X to cut or
<Ctrl>+C to copy; use <Ctrl>+V to paste. Since the cut and copy operations store
the information in the Windows Clipboard, points may be pasted to another CXSupervisor application. See also Chapter 3 Quick creation of many points.
Note:
If the I/O type ends with ‘∗’ and a number, it is an array point with the shown
number of elements.
Viewing Points in the Point Editor
The Point Editor view of the points database can be tailored by filtering or sorting the available
points.
Filtering the Points in the View by Group
Points are separated into groups. To select a group, pick an entry from the Group field.
All points can be displayed by selecting <All Groups> from this list.
Filtering the Points in the View by Point Type
A selection of points can be displayed based on the point type. Selection of the All
Points button from the toolbar displays points of all types.
The Boolean Points button only displays points of a Boolean type. The Integer Points button, the
Real Points button and Text Points button, once selected, react in the same way.
Sorting the Points in the View by I/O Type
Points can also be filtered by I/O type. Respectively, these toolbar buttons display
All Points, Memory Points, Input Points, Output Points or Input/Output Points.
Sorting the Points in the View
Individual listed points are sorted, based on a designated field type: name, type,
input/output type or description. By clicking on the Name button, the points are
sorted alphanumerically by name. The Type button, the I/O Type button, the
Address button and Description button, once selected, react in the same way. In the
previous Point Editor example the list is sorted by Name.
The widths of the point fields can be widened or narrowed as required using the
mouse to drag the column boundaries:
A double click on the text boundaries causes the column to autosize.
Page 24
Release 1.2
OMRON
CHAPTER 3 – Points
Changing the Viewing Mode
Select the View Settings button to configure which columns of information are displayed in
the Point Editor.
Select the Large Icons button to view details with large icons.
Select the Small Icons button to view details with normal icons.
Select the List button to view details as a list.
Select the Details button to view details as a list including name, type, I/O type, address and
description information. The details can be sorted in ascending order by clicking once or in
descending order by clicking twice, in the appropriate field.
Summary of Point Information
A summary of point information is available by selecting the Display Information on
Points button from the toolbar. The resultant Point Information dialog shows an overall
summary, a breakdown on the number of points per type and the input/output type. To exit
the dialog, click the Close pushbutton. The Point Information dialog is shown as follows:
Drag and Drop of Points onto Control Objects
The Point Editor can be used to drag and drop points onto control objects. For instance, Integer
points can be dragged from the Point Editor onto a Linear Gauge, Rotary Gauge, Trend Graph and
Slider. Boolean points can also be applied to a Toggle.
Release 1.2
Page 25
CHAPTER 3 – Points
OMRON
To apply a point to a control object with the Point Editor:
1, 2, 3…
1.
Arrange the CX-Supervisor windows so that the point to drag and the
target control object are both visible.
2.
Select the point to associate and drag it onto the page.
3.
Drop the point at the position of the target control object. An invalid
“drop” is denoted by the mouse pointer changing to a circular symbol.
For further information of the use of points with objects, refer to chapter 4, Objects.
Page 26
Release 1.2
OMRON
CHAPTER 3 – Points
Creating a Point
To add a new point, select the Add Point button from the toolbar. This results in the Add
Point dialog being displayed:
Once all the information has been provided for the new point, clicking the OK pushbutton commits
the new point to the points database, whilst the Cancel pushbutton aborts the add operation.
General Attributes
The name of the point is entered in the Point Name: field. The point name can be up to 20
alphanumeric characters, and must not begin with a digit or include mathematical operators such as
“+”, or be identical to a script reserved word such as “IF” or “cos”. Any invalid characters (including
spaces) generate an audible error, or an “Invalid Point Name entered” message when the OK
pushbutton is clicked.
The group to which this point belongs is selected from the Group: field. A new group can be entered
by typing in the Group: field.
A points description, detailing the use of the current point, may be inserted in the Description: field.
Point Type
The point type can be Boolean, Integer, Real or Text. The default type is Boolean.
Release 1.2
Page 27
CHAPTER 3 – Points
OMRON
Point Attributes
The attributes for a point vary according to the point type.
For a Boolean point, the following attributes are displayed:
The default state of the point is defined by selecting either the State 0: or State 1: setting.
Associative text (such as ‘OFF’ or ‘FALSE’ for state 0) can be applied in the related Default Text:
fields. The default text is associated with Toggle buttons and object animations such as Display
Value and Edit Point Value when they are configured to use the point.
For an Integer point, the following attributes are displayed:
The minimum threshold for the point is inserted into the Minimum Value: field.
The maximum threshold for the point is inserted into the Maximum Value: field.
The default value is inserted in the Default Value: field.
For a Real point, the following attributes are displayed:
The minimum threshold for the point is inserted into the Minimum Value: field. The maximum
threshold for the point is inserted into the Maximum Value: field.
The default value is inserted in the Default Value: field.
Page 28
Release 1.2
OMRON
CHAPTER 3 – Points
For a Text point, the following attribute is displayed:
Text is entered in the Text: field. Up to 255 characters may be entered.
I/O Type
The I/O type states the scope of the point, i.e. whether it is purely an internal variable or whether it
communicates with a PLC.
♦
A Memory Resident point is provided internally by CX-Supervisor.
♦
An Input point receives data from an external device.
♦
An Output point sends data to an external device.
♦
An Input/Output point both sends data to and receives data from an external device.
Memory Attributes
The Array Size field allows Memory Point arrays to be created. If an Array Size of 1 is specified, a
single point is created. Specifying any other value creates an array of points of this type.
This option is only available to Memory Resident points.
Release 1.2
Page 29
CHAPTER 3 – Points
OMRON
I/O Update Rate
The I/O Update Rate specifies how and when communication with the PLC takes place.
This option is not available to Memory Resident points.
The On Change option specifies that communication with the PLC occurs automatically as a result of
a value change.
The On Request option specifies that data updates with the PLC will be manually requested using the
scripting commands InputPoint and OutputPoint. The point is updated internally but only
communicates with the PLC when requested to by the script commands.
The On Interval option specifies the frequency that communications occur with the PLC. When this
option is selected an edit box appears allowing the frequency to be entered:
I/O Attributes
The I/O Attributes option specifies the external source or destination for the point.
This option is not available to Memory Resident points.
The external source is defined by selecting the appropriate I/O Attributes: setting.
configuration of the external source can be applied by clicking the Setup pushbutton.
Further
On clicking the Setup pushbutton for a PLC external source, the PLC Attributes dialog is displayed.
Page 30
Release 1.2
OMRON
CHAPTER 3 – Points
The point type associated with the PLC Connection attributes is shown in the title bar. The required
PLC can be selected from the PLC: field. If no PLCs exist in the PLC: field then one must be added.
This is achieved by clicking the Add PLC pushbutton and configuring one. A point cannot be
configured to have a PLC connection unless all the PLC connection attributes are correctly
configured. For more information on adding and configuring PLCs and devices see chapter 6
Projects, Device Configuration.
PLC Attributes
The Data Location: field identifies the area of memory to which this address applies and is dependent
upon the type and configuration of the PLC.
The Data Type: field identifies the type of data held at this address. The type determines how point
values are converted from a computer format into a PLC format. The field contains options
applicable to the Data Location.
The Modifier: field indicates the command to be performed on the data at this address. An example
of a modifier is for a bit: a modifier might declare that a bit is to be forced set and not to be written
normally. The field contains options applicable to the Data Location.
Release 1.2
Page 31
CHAPTER 3 – Points
OMRON
The Array Size: field specifies the number of data values associated with the point. A value greater
than 1 allows the point to be treated as an array. For more detail on array points and their uses see
Optimisation of PLC Communications.
The PLC Attributes dialog takes on a slightly different appearance if the point type is text, showing
the number of characters which start at the specified data location:
Data Transfer Actions When Opening a PLC
The type of data transfer action for the selected PLC can be specified by selection of the appropriate
setting. Options for Input and Input/Output points are Always Update Point Value and Only Update
Point Value When On Display. Options for an Output point are Write Value, Read Value and No Data
Transfer.
Conversion Attributes
The minimum and maximum PLC value and the application of a conversion factor is specified in the
Conversion Attributes: fields (these fields are not applicable for Boolean and text points).
Conversion Attributes can be used to convert in a linear fashion between a value in a PLC and the
point range. For example, if the possible range in the PLC is 0 to 1000, and the point range is 0 to
100, then a PLC value of 500 would correspond to a point value of 50. The conversion would be
performed just before the data is sent to the PLC, or immediately upon receipt of it from the PLC.
On completion of the PLC configuration connection, click the OK pushbutton to continue, or the
Cancel pushbutton to abort. Click the Add PLC pushbutton to create a new PLC connection.
Information relating to the selection of this pushbutton is described in chapter 6 Projects, Device
Configuration.
Advanced Point Settings
Advanced settings can be applied to a new point, by clicking the Advanced pushbutton in the Add
Point dialog. This results in the Advanced Point Settings dialog being displayed.
Page 32
Release 1.2
OMRON
CHAPTER 3 – Points
In order to access a CX-Supervisor point value via OLE2 Automation or Dynamic Data Exchange, it
must be given OLE Read or OLE Write access. The scope of the access can be defined by checking
the appropriate setting in the OLE Access and DDE Access options.
The point value which is stored to disk may be Volatile or Non-volatile by selecting or deselecting
the Non-Volatile check-box. A Non-volatile point ensures the preservation of the point’s value at
regular intervals. If power is lost, or CX-Supervisor is shut down for any reason, then when the
application is restarted the point is initialised to the last saved value.
Select the Validate Point is Within Specified Range check-box. This option is only available for
Input or I/O points of type Integer or Real. When checked, an error message is displayed in the error
log if the data passed to CX-Supervisor is outside of the specified Minimum and Maximum range.
Click the OK pushbutton to accept the advanced settings, or the Cancel pushbutton to abort the
operation.
Amending an Existing Point
To modify an existing point, highlight the point from the points list and click the Modify
Point button from the toolbar.
This results in the View Point dialog being displayed as shown below, a dialog based on the Add
Point dialog:
Release 1.2
Page 33
CHAPTER 3 – Points
OMRON
The selected point can be redefined as described in chapter 3, Creating a Point.
Deleting an Existing Point
To remove an existing point, highlight the point from the points list and click the Delete
Point button from the toolbar. This results in a confirmation dialog being displayed. Click
the Yes pushbutton to remove the point from the points database, or the No pushbutton to
abort the delete operation.
Note: It is possible to delete more than one point by either selecting points within a range or
by selecting individually several points.
To select a range click on a point to mark the start of the range and click again with the <SHIFT> key
down to mark the end.
To individually select more than one point click whilst holding the <CTRL> key down.
Page 34
Release 1.2
OMRON
CHAPTER 3 – Points
Quick creation of many points
CX-Supervisor supports up to 8,000 points, which could take much time to create. Within the Point
Editor you can use Copy/Paste which helpfully increments the point name automatically
(BoilerTemp1 becomes BoilerTemp2, BoilerTemp3 etc) but you still have to edit each point to
configure the PLC address and possibly other information. Using the Copy and Paste functions, Point
data can quickly be edited and created for example in grid form using Excel. This can prove
extremely quick when the design uses contiguous addresses.
1, 2, 3…
1.
Open the Point Editor.
2.
Select the points to edit, or a single point to act as a template and Copy to the Windows
Clipboard
3.
Start Excel.
4.
Position the cursor in column A and paste the CX-Supervisor Points into Excel. The
worksheet should resemble the following:
Each row is a single point, and each column is a setting of that point.
Note:
5.
Some settings may be hidden on the right. Use the scrollbar to view.
Edit the point details as required.
Note: To quickly create new points with the same settings, select the whole row by
clicking the row number on the left. A range can now be drawn to be filled by dragging the
black square box on the bottom left of the range selection:
Release 1.2
Page 35
CHAPTER 3 – Points
OMRON
Excel will automatically increment any data ending in a number. This can be very useful for
Names and PLC Addresses (columns A and F) but take care with other columns. If other
columns are wrongly incremented, like PLC Name, Array size and Data Range (columns E,
G and K) these can quickly be copied by selecting the correct value e.g. G1 then using the
square box to highlight the column of data to fill. To see the fill options hold down the right
mouse button before draging the square box. Repeat for each column.
6.
When editing is completed, select the row(s) to required and select Copy
7.
Switch back to the Point Editor and select Paste.
Note: If the pasted point names already exist, CX-Supervisor will automatically add or
increment a number on the end to prevent overwriting. If you wish to overwrite to replace
old point settings, simple delete (not Cut) the old points from the Point Editor before pasting.
Note:
All pasted points will pasted into the group on view
Runtime Point Maintenance
It is possible to reconfigure points at runtime via the right mouse button floating menu option Points
Maintenance. The Point Maintenance dialog is displayed.
Page 36
Release 1.2
OMRON
CHAPTER 3 – Points
To monitor and change the value of a point in runtime, select a point from the Point Name: field.
The Filter Options: field and settings refines the points listed in the Point Name: field. Select the
Get Value pushbutton to retrieve the current value of the selected point. Specify a new point value in
the Point Value/Text: field and click the Set Value pushbutton. The Diagnostics button shows
details including communications statistics, useful for diagnosing communication problems. Note this
button is only available when a user with ‘Designer’ privileges is logged in. Select the Close
pushbutton to complete the operation.
Optimisation of PLC Communications
PLC communication speeds can be increased by creating “array” points which contain several
elements of the same type, rather than creating a large number of individual points. For instance, the
time taken to update an array point containing 50 elements are quicker than the time taken to update
50 individual points.
Creation of an “Array” Point
An “array” point can be created by specifying a value greater than 1 in the Elements: field of the
Setup PLC Connection dialog. The Data Location field specifies the memory address from which the
array of data begins.
Note:
Elements of an array point are located at consecutive addresses after the address
specified in the Data Location field.
Accessing Elements of an “Array” Point
Access to array point elements is achieved via the script functions GetPointValue() and
SetPointValue(). Both these functions allow the ability to specify an index into a point array. For
more information on these functions refer to the CX-Supervisor Script Language Reference Manual.
Direct access to array points can be achieved by applying a subscript to the pointname, e.g.
pointname[index].
Point Import
To import PLC points from other applications, click the Import PLC Points button from the
toolbar. This results in the Import PLC Points From Another CX-Server Project dialog being
displayed.
The Point Import tool can be used to import point information into the CX-Supervisor project that has
already been configured. The symbol name, symbol type and PLC address is imported from the
CDM file generated by other applications.
The CDM file can be generated from CX-Programmer by linking the project to the CDM file. The
CDM file can also be generated by exporting from a SYSWIN project to a CDM file. Refer to the
documentation supplied with the package for information on how to export or link the data to the
CDM file.
Release 1.2
Page 37
CHAPTER 3 – Points
OMRON
It is possible to import points from the CDM file of another CX-Supervisor project but this is not
recommended, as only the name, type and address are imported. A better method is to copy the
points from one application to the clipboard, and paste them in the required application. This way all
point information is copied.
Steps to import from another CDM file.
1)
Open the Import PLC Points From Another CX-Server Project dialogue
2)
Press Open Project and find the project to import from
3)
Select the tab depending upon the I/O type required
4)
Click the Add button and select the symbols required
5)
Add these to the CX-Supervisor project by clicking the Add button
6)
Press OK to return
7)
Repeat for other I/O types
8)
Press OK to finish
System Points
System Points are those points that are pre-defined within CX-Supervisor. They cannot be edited or
deleted, but their attributes can be viewed. All system points can be selected from the System Point
dialog.
System points are listed in the points list, and are denoted by a ‘$’ symbol preceding the point name.
To view system points only, select System Points from the Group: field. Once listed, the Boolean
Points, Integer Points, Real Points, Text Points and All Points pushbuttons on the toolbar are
unavailable for selection. To view other points, select All Groups from the Group: field.
Time Points
The following table describes system points for use with time based operations. Provisions are given
to both 12 hour and 24 hour time formats.
System point
Page 38
Point type
Point range
Remarks
$12Hour
Integer
0-12
$AMPM
Text
—
$Hour
Integer
0-23
Hours in 24-hour format.
$Millisecond
Integer
0-999
Number of milliseconds.
$Minute
Integer
0-59
Minutes.
Hours in 12-hour format.
AM/PM indicator for 12-hour clock form.
Release 1.2
OMRON
CHAPTER 3 – Points
$Second
$Time
Integer
0-59
Text
—
Seconds.
Time (e.g. 09:46).
Date Points
The following table describes system points for use with date based operations. Provisions are given
for numerical and alphanumerical formats.
System point
Point type
Point range
Text
—
$DayOfMonth
Integer
1-31
Day of the month.
$DayOfYear
Integer
1-366
Day of the year.
$Month
Integer
1-12
Month ( 1 - January, 12 – Dec.).
$MonthName
Text
—
Month name (e.g. February).
$ShortMonthName
Text
—
Abbreviated month name (e.g. Feb).
$ShortWeekDayName
Text
—
Abbreviated weekday name (e.g. Wed).
$ShortYear
Integer
0-99
Abbreviated year (e.g. 95).
$WeekDay
Integer
0-6
Day of the week (0 - Sun, 6 – Sat).
Text
—
Weekday name (e.g. Wednesday).
$WeekOfYear
Integer
0-51
$Year
Integer
1970-2038
$Date
$WeekDayName
Remarks
Date (e.g. 28/02/95).
Week number for the year.
Year (e.g. 1995).
Internal Points
The following table describes system points for use with interrogating current system settings, such
as memory and disk space restrictions and other system resources.
System point
Point type
Point range
$AvailableMemory
Integer
0-2,147,483,647
$DemoMode
Boolean
—
$DiskSpace
Integer
0-2,147,483,647
$PCName
Text
-
Computer name of PC as seen in Explorer
$ProjectName
Text
-
Name of project file, without .SCS
extension
$ProjectPath
Text
-
Path to project on disk, without project
Release 1.2
Remarks
Amount of available memory, in bytes.
Indicates whether a valid token has been
installed.
Amount of free disk space available, in
bytes.
Page 39
CHAPTER 3 – Points
OMRON
name.
$SpoolCount
$Version
Integer
0-2,147,483,647
Text
-
Number of alarm entries currently spooled,
awaiting printing to page printer.
Version number of CX-Supervisor
Runtime program
Display Points
The following table describes system points for use with the display mode.
System point
Point type
Point range
Remarks
$ScreenSizeX
Integer
0-2,147,483,647
Screen width.
$ScreenSizeY
Integer
0-2,147,483,647
Screen height.
Mouse Points
The following table describes system points for use in mouse movement and operation. They are
updated on a left button click.
System point
Point type
Point range
Remarks
$MouseX
Integer
0-65535
Mouse X co-ordinates.
$MouseY
Integer
0-65535
Mouse Y co-ordinates.
Alarm Points
The following table describes system points for use with CX-Supervisor alarms.
System point
Point type
Point range
Remarks
$ActiveAlarms
Integer
0-2,147,483,647
Number of active alarms.
$AlarmCount
Integer
0-2,147,483,647
Total number of alarms.
$HighestAlarms
Integer
0-2,147,483,647
Number of active highest priority alarms
$HighAlarms
Integer
0-2,147,483,647
Number of active high priority alarms
$MediumAlarms
Integer
0-2,147,483,647
Number of active medium priority alarms
$LowAlarms
Integer
0-2,147,483,647
Number of active low priority alarms
$LowestAlarms
Integer
0-2,147,483,647
Number of active lowest priority alarms
$Unacknowledged
Alarms
Integer
0-2,147,483,647
Number of alarms currently unacknowledged
Error Logger Points
The following table describes system points for use with CX-Supervisor errors.
Page 40
Release 1.2
OMRON
CHAPTER 3 – Points
System point
Point type
Point range
Remarks
$HighErrors
Integer
0-2,147,483,647
Number of high priority errors logged.
$LowErrors
Integer
0-2,147,483,647
Number of low priority errors logged.
$MediumErrors
Integer
0-2,147,483,647
Number of medium priority errors logged.
PLC Communications Points
The following table describes system points for use in the communication between CX-Supervisor
and a PLC.
System point
Point type
Point range
Remarks
Real
—
Reports average number of PLC input points
read per second since application startup.
$PLCBusy
Boolean
—
Indicates if PLC communications are busy.
$PLCFailures
Integer
0-2,147,483,647
$InputsActual
Total number of PLC failures.
Security Points
The following table describes system points for use with user login, logout, and user privileges in the
runtime environment.
System point
Point type
Point range
Remarks
$SecurityLevel
Integer
0-4
Current user’s security level.
$SecurityName
Text
—
Current user’s security name.
$UserName
Text
—
User currently logged on.
Printing Points
Print Setup
The Point Editor can be printed in the same way pages can. Before printing, ensure that the printer
has been set up correctly. To check the printer settings, refer to chapter 2, Pages.
Print Preview
To preview the page before printing, select Print Preview from the File menu.
Refer to chapter 2, Pages regarding the use of the Print Preview display.
Printing
To print the contents of the Point Editor, select the Print button from the toolbar.
Release 1.2
Page 41
CHAPTER 3 – Points
OMRON
Refer to chapter 2, Pages regarding the use of the Print dialog.
Page 42
Release 1.2
OMRON
CHAPTER 4 – Objects
CHAPTER 4
Objects
This chapter describes the various objects available within CX-Supervisor. It also describes the
processes for creating, editing and manipulating objects.
Objects
Pages created with CX-Supervisor are constructed from objects that are inserted and linked together
to form a coherent interface. CX-Supervisor objects are divided into three groups: graphical, control
and embedded.
Generally, the procedures for creating objects are identical. A pushbutton representing the desired
object is clicked on the Graphic Object bar. The mouse pointer is then either clicked on the page (for
a default sized object), or clicked and dragged to the appropriate point on the page for a custom sized
object.
Editing Objects
Editing falls into three distinct categories:
♦
Re-sizing an object.
♦
Re-shaping an object.
♦
Modifying an object using a Wizard.
Re-sizing
To re-size an object, click on it with the left mouse button. This ‘selects’ it and brings up green
sizing grab handles. Click and drag the handles until the object is of the desired size.
Re-shaping
Re-shaping procedures are similar for all graphical objects which can be reshaped. Not all can.
Control objects can only be reshaped using Wizards.
To change the shape of a graphical object, choose Edit Object from the Edit menu to bring up the red
editing grab handles. Click and drag the handles until the object is of the desired shape.
The typeface of the editor can be amended by choosing Preferences from the File menu. This is
especially useful when printing.
CX-Supervisor preferences can be configured such that double-clicking on a graphical object also
brings up the red editing grab handles. Setting this preference is achieved by selecting Preferences
from the File menu. Refer to chapter 2, Pages for further details on preferences and CX-Supervisor
configuration.
Release 1.2
Page 43
CHAPTER 4 – Objects
OMRON
Wizards
Control objects cannot be re-shaped in the same way as a graphical object but are edited using
Wizards. Wizards customise control objects to display information in an easy to understand manner.
To edit a control object and activate a Wizard, double click on the object.
Note:
The shortcut keyboard combinations for Cut, Copy and Paste operations are valid
within Wizards. Highlight part or all of a field and type <Ctrl>+X to cut the text or
<Ctrl>+C to copy the text; move the cursor to the desired field and type <Ctrl>+V
to paste the text. Since the cut and copy operations store the information in the
Windows Clipboard, they may be pasted to another Wizard, dialog or application.
Creating and Editing Graphic Objects
For details on re-sizing the graphic objects described in the following paragraphs, refer to chapter 3,
Editing Objects.
Arc
Arcs may be transparent or filled with a colour or pattern. To insert an Arc, select the Arc
button from the Graphic Object bar. Click or click and drag on the page.
To edit the arc, obtain the red grab handles. Click and drag to change the angle subtended by the arc.
To finish editing, click elsewhere on the page or press <Esc>.
Block Text
To insert block text, click the Block Text button, and then click on the page. Stretch the text
object to resize it. Standard text tools from the toolbar and the keyboard (e.g. bold, italic,
left-justify) can be used, and their effect applies to the whole content of the object.
To edit block text, double click on it. A Text-Editing dialog is displayed. The text can then be
changed, as can the word-wrap and border options. Standard Windows cut, copy and paste facilities
can be used.
Ellipse
Ellipses may be transparent or filled with a colour or pattern. To create a filled ellipse, click
the Ellipse button.
To create a transparent ellipse, click the Ellipse Frame button. Alternatively, select a filled
ellipse and click the Transparency.
Either click on the page to create a circle, or click and drag to create an ellipse. Ellipses cannot be
edited but can be re-sized.
Page 44
Release 1.2
OMRON
CHAPTER 4 – Objects
Line
To insert a line, click on the Line button. Click and drag on the page to draw a line of the
required length.
To edit the line, obtain the red grab handles. Click and drag to change the line. To finish editing
click elsewhere on the page or press <Esc>.
Polygon
Polygons may be transparent or filled with a colour or pattern. To create a polygon, click the
Polygon button. Click on the page to draw vertices. To finish creating the polygon either
click the right mouse button, press <Esc> or double click the left mouse button.
To edit the polygon obtain the red grab handles. Click on an edge to add a vertex or click and drag a
vertex to move it.
To finish editing, either click elsewhere on the page or press <Esc>.
To split a straight line into two, click at the point on the line where the split is required then drag the
mouse. CX-Supervisor creates a new handle which may be moved to the desired point. To remove a
red handle and the vertex on which it rests, click on it with the delete key held down on the keyboard.
Polyline
To create a polyline, click the Polyline button. Click on the page to draw vertices. To finish
creating the polyline, click the right mouse button.
To edit a polyline, obtain the red grab handles. Click on an edge to add a vertex. Press the <Delete>
key whilst moving a vertex to delete it.
To finish editing, click elsewhere on the page.
Rectangle
Rectangles can be transparent or filled with a colour or pattern. To create a filled rectangle,
click the Rectangle button.
To create a rectangle frame, click the Rectangle Frame button. Alternatively, select a filled
rectangle and click the Transparency button from the toolbar.
Click on the page to draw a square, or click and drag to create a rectangle of the required size. Once
created, rectangles can be edited exactly like polygons.
To finish editing, click elsewhere on the page.
Round Rectangle
Rounded rectangles can be transparent or filled with a colour or pattern. To create a filled
rounded rectangle, click the Round Rectangle button from the Tool Bar.
Release 1.2
Page 45
CHAPTER 4 – Objects
OMRON
To create a rounded rectangle frame, click the Round Rectangle Frame. Alternatively,
select a filled round rectangle and click the Transparency button from the Control Bar.
Click on the page to draw a rounded square, or click and drag to create a rounded rectangle of the
required size.
To edit the rounded rectangle, obtain the red grab handles. The radius of curvature of the rounding
can be adjusted by clicking on the single red grab handle and dragging it, as illustrated below:
Text
To insert text, click the Text button. Click on the page and type inside the red edit box. The
cursor is moved round the text using the arrow keys. Standard text editing tools from the
toolbar and the keyboard can be used, and their effect applies to the whole content of the
object.
To edit text, double click on it. A box is displayed round the text.
Press <Return> to finish editing and create a new text object on the line below. To finish editing,
click elsewhere on the page.
Creating and Editing Control Objects
Alarm Object
Click the Alarm button, then click or click and drag on the page to insert the alarm object.
The Alarm object displays alarm messages in runtime. These messages may be optionally filtered by
an alarm group and can be formatted to include the date, time and status of the alarm.
To edit an Alarm object, double click on it. The Alarm Wizard dialog is displayed as follows:
Page 46
Release 1.2
OMRON
CHAPTER 4 – Objects
Alarms are defined using the Alarm Editor; refer to chapter 8, Alarms for information on using the
Alarm Editor.
The Alarm Wizard allows entry of the alarm group filter, alarm status colour codes and various style
attributes. The Alarm Wizard presents a preview of the alarm object, which immediately updates to
show the user selections as they are made.
1, 2, 3…
1.
Select the name of the alarm group by which alarm messages are to be
filtered using the Group field to display the list of available groups. The
default selection is <All Groups>, which displays all alarm messages.
To display more than one group use the * wildcard character e.g. Group1*
will include all groups starting Group1.
2.
Release 1.2
From the Acknowledge On Click options select the level of security that is
required for acknowledgement. The default is All Users.
Page 47
CHAPTER 4 – Objects
OMRON
3.
From the Display Alarms from Selected Priorities, options select the range
of alarms that are to be displayed. The default selections are from the
Lowest to the Highest.
Note that the range ‘From’ must be the same or lower than the range ‘To’.
Use the check box ‘Highest Priority at Top’ to reverse the alarm order.
4.
In Alarm Status Colours, the colour codes for each of the three alarm states
and blinking colours may be specified by clicking the appropriate colour
box and selecting a new colour from the resultant Colour dialog.
5.
The Alarm Window Colours options allow you to select the colours for the
Alarms Windows Background, Title text and the Frame.
6.
Select the font used by the alarm object using the Font pushbutton.
7.
In Style Attributes, set the following options as desired:
Display Date:
Display Time:
Display Alarm Status:
Display Column Titles:
3-D Frame:
Highest Priority at Top:
Display Group:
Display Priority:
Date Width:
Time Width:
Group Width
Status:
8.
shows the date of the alarm.
shows the time of the alarm.
shows the status of the alarm.
shows the column headings.
displays object with 3-D border.
shows highest priority at top.
shows the groups of the alarm.
shows the priority of the alarm.
number of characters in date field.
number of characters in time field.
number of characters in priority field
number of characters in status field.
Exit the Wizard by clicking the OK pushbutton to accept the new alarm
object attributes or click the Cancel pushbutton to leave the alarm object
unchanged.
Bar Chart
Click the Chart button, then click or click and drag on the page to insert the Chart.
To edit a Bar Chart, double click on it. The Chart Wizard dialog is displayed as follows:
Page 48
Release 1.2
OMRON
CHAPTER 4 – Objects
The Chart Wizard allows entry of configuration attributes and assignment of expressions.
1, 2, 3…
1.
Enter a title for the chart in the Chart Title: field.
2.
Select the chart style from the Chart Style: field.
3.
Select the colour of the chart background.
4.
Toggle the Project Colours, 3-D Frame and Auto Fit Bars fields as desired.
The Project Colours option allows the user to change the colour of the axis
using the toolbox. The 3-D Frame option enables the chart to appear with a
3-D frame. The Auto Fit Bars option forces the configured bars to resize
themselves to occupy all of the available chart area.
5.
Change the fonts used for the chart via the Font pushbutton. The font size
used for the chart can be automatically calculated by selecting the Auto Size
Font option.
6.
Enter an arithmetic trace expression for each point or select one by clicking
on a Browse pushbutton. An existing point can also be associated with the
Wizard by dragging a point directly from the Point Editor. Refer to chapter
3, Points regarding adding a new point and dragging from the Point Editor.
7.
Exit the Wizard by clicking the OK pushbutton to accept the new chart
attributes, or click the Cancel pushbutton to leave the chart unchanged.
To select the chart scaling, click the Scaling pushbutton; the Axis Scaling dialog is displayed as
follows:
Release 1.2
Page 49
CHAPTER 4 – Objects
OMRON
The Configuration Attributes fields can be altered by typing over the existing entries. The Style
Attributes fields can be amended by clicking on the settings.
Exit the Axis Scaling dialog by clicking the OK pushbutton to accept the scaling attributes, or click
the Cancel pushbutton to leave them unchanged.
Pictures
Pictures and graphics can be inserted on a page in the form of bitmaps (.bmp) or Windows
metafiles (.wmf). Click the Picture button, then click or click and drag on the page to insert
a picture placeholder.
To insert a picture, double click on the placeholder. The Picture Wizard dialog is displayed as
follows:
Page 50
Release 1.2
OMRON
CHAPTER 4 – Objects
1, 2, 3…
Note:
1.
Locate the drive and directory where the desired picture is stored using the
Directories: and Drives: controls.
2.
Select the file type and then the picture from the list presented.
3.
Use the Display picture at original size setting to specify whether the
picture is to be displayed at original size or scaled.
4.
Click the OK pushbutton to load the page.
If the PC installation of CX-Supervisor is on a networked machine, a Network
pushbutton is added to the dialog. For further information on the function of the
Network dialog, refer to the Microsoft Windows User Guide.
A bitmap or Windows metafile image can be selected and resized just like a graphical object.
Linear Gauge
A Gauge provides a display of operational values. Click the Linear Gauge button, then
click or click and drag on the page to insert the gauge.
To edit a Linear Gauge object, double click on it. The Gauge Wizard dialog is displayed as follows:
Release 1.2
Page 51
CHAPTER 4 – Objects
OMRON
The Gauge Wizard dialog allows entry of the Gauge Style:, Configuration Attributes:, Style
Attributes: and Style Specific Attributes: fields.
To select a style, click on an option from the appropriate field. To select an Expression Attribute,
click on the Browse pushbutton and select a point from the displayed list. The Select Required Item
dialog is displayed; click the OK pushbutton to accept the point or click the Cancel pushbutton to
leave the point unselected. Clicking the Add Point button from the toolbar allows a new point to be
created prior to association with the Gauge Wizard. An existing point can also be associated with the
Gauge Wizard by dragging a point directly from the Point Editor. Refer to chapter 3, Points
regarding adding a new point and dragging from the Point Editor.
To enter gauge values or display units, type over the existing field entries.
The Gauge can be displayed in linear or rotary format, either with or without ticks.
The text font used for the gauge title can be changed via the Title Font pushbutton. The text font
used for the gauge scale can be changed via the Scale Font pushbutton. The font size used by the
gauge can be automatically calculated for the user by selecting the Auto Size Fonts field.
Exit the Gauge Wizard by clicking the OK pushbutton to accept the new gauge attributes or click the
Cancel pushbutton to leave the gauge unchanged.
Pushbutton
Pushbuttons provide a simple means to start a set of actions. Click the Push Button button,
then click or click and drag on the page to insert a pushbutton.
To edit the pushbutton, double click on it. The Push Button Wizard dialog is displayed as follows:
The Wizard allows a pushbutton to be assigned a style or text or both to signify its purpose. To select
a style, click on an option in the Button Style field. To enter button text, type in the Button Text field
(the Style Attributes: dialog is automatically updated). The text font can be changed via the Font
pushbutton. Click the OK pushbutton to accept the new button attributes, or click the Cancel
pushbutton to leave the button unchanged. Examples of the different styles of pushbutton are
illustrated below:
Page 52
Release 1.2
OMRON
CHAPTER 4 – Objects
The colour of the coloured pushbutton is red by default, but can be changed by using the Palette.
Rotary Gauge
A Gauge provides a means of displaying the value of an operation or the value of a point.
Click the Rotary Gauge button, then click or click and drag on the page to insert a gauge.
To edit the Rotary Gauge, double click on it. The Gauge Wizard dialog is displayed as follows:
The Wizard allows entry in the Gauge Style:, Configuration Attributes:, Style Attributes: and Style
Specific Attributes: fields.
Release 1.2
Page 53
CHAPTER 4 – Objects
OMRON
To select a style, click on an entry in the Gauge Style field. To select an Expression Attribute, click
on the Browse pushbutton and select a point from the displayed list. The Select Required Item dialog
is displayed; click the OK pushbutton to accept the point or click the Cancel pushbutton to leave the
point unselected. Clicking the Add Point button from the toolbar allows a new point to be created
prior to association with the Wizard. An existing point can also be associated with the Wizard by
dragging a point directly from the Point Editor. Refer to chapter 3, Points regarding adding a new
point and dragging from the Point Editor.
To enter gauge values or display units, type over the existing field entries. Enter display angles by
typing over the existing field entries.
Check the boxes to choose the required style attributes. The Gauge can be displayed in linear or
rotary format, either with or without ticks.
The text font used for the gauge title can be changed via the Title Font pushbutton. The text font
used for the gauge scale can be changed via the Scale Font pushbutton. The font size used by the
gauge can be automatically calculated for the user by selecting the Auto Font Size option.
Exit the Wizard by clicking the OK pushbutton to accept the new gauge attributes or click the Cancel
pushbutton to leave the gauge unchanged.
Scatter Graph
Click the Scatter Graph button, then click or click and drag on the page to insert a graph.
To edit the graph, double click on it. The Scatter Graph Wizard dialog is displayed as follows:
Page 54
Release 1.2
OMRON
CHAPTER 4 – Objects
The Wizard allows entry in the Configuration Attributes: and Expressions fields.
1, 2, 3…
1.
Enter the frequency of data sampling in the Sample Rate: field; in this
example the sample rate is every thirty seconds.
2.
Enter the maximum number of samples to be displayed on the scatter graph
in the Max Samples: field.
3.
Select the type of symbol to represent the data.
4.
Select the colour of the symbol representing the data.
5.
Select the colour of the scatter graph background.
6.
Toggle the Project Colours and 3-D Frame settings as desired. If set, the
Project Colours field allows the colour of the axis to be changed using the
Palette. The 3-D Frame option enables the graph to appear with a 3-D
frame.
7.
Either enter an arithmetic expression for the X and Y axis or select one
through the Browse pushbutton. An expression point can also be
associated with the Scatter Graph Wizard by dragging a point directly from
the Point Editor. Refer to chapter 3, Points regarding adding a new point
and dragging from the Point Editor.
8.
Change the fonts used for the Scatter Graph via the Font pushbutton. The
font size used by the graph can be automatically calculated for the user by
selecting the Auto Size Font field.
9.
Exit the Scatter Graph Wizard by clicking the OK pushbutton to accept the
new scatter graph attributes or click the Cancel pushbutton to leave the
scatter graph unchanged.
To configure the X axis, click the X-Axis pushbutton. To configure the Y-axis , click the Y-Axis
pushbutton. The Axis Scaling dialog is displayed:
Release 1.2
Page 55
CHAPTER 4 – Objects
OMRON
Configuration attributes can be altered by typing over the existing field entries. The style attributes
can be amended by clicking on the settings.
Exit the Axis Scaling dialog by clicking the OK pushbutton to accept the scaling attributes, or click
the Cancel pushbutton to leave unchanged.
Slider
Sliders allow values associated with them to increase or decrease between certain limits.
They can also ensure that values do not exceed previously set limits.
Click the Slider button, then click or click and drag on the page to insert a slider.
To edit the Slider, double click on it. The Slider Wizard dialog is displayed as follows:
The Wizard allows entry of in the Slider Style:, Style Attributes: and Configuration Attributes: fields.
To select a style, click on an option from the list box. The Style Attributes: can be either Display
Vertical or Display Horizontal. To select a Boolean point, click on the Browse pushbutton and select
a point from the displayed list. Click the OK pushbutton to accept the point or click the Cancel
pushbutton to leave the point unselected. Clicking the Add Point button from the toolbar allows a
new point to be created prior to association with the Wizard. An existing point can also be associated
with the Wizard by dragging a point directly from the Point Editor. Refer to chapter 3, Points
regarding adding a new point and dragging from the Point Editor.
Enter the maximum and minimum slider values and check the box to display the minimum value at
the left or bottom of the page.
Exit the Wizard by clicking on the OK pushbutton to accept the new slider attributes or click on the
Cancel pushbutton to leave the slider unchanged.
Page 56
Release 1.2
OMRON
CHAPTER 4 – Objects
Toggle Button
Toggle buttons are used to control and display the current value of a digital point. Click the
Toggle Button button, then click or click and drag on the page to insert a button.
To edit the Toggle Button, double click on it. The Toggle Button Wizard dialog is displayed as
follows:
The Toggle Button Wizard allows a Toggle Button to be assigned a style, State 0 text and State 1 text
to signify its purpose. It also allows selection of a Boolean point. To select a style, click on an
option from the list box. To enter button text, type in the Text fields for States 0 and 1, or select ON
and OFF (the Style Attributes: dialog is automatically updated). Some toggle buttons can have an
On/Off colour associated with them. The text font can be changed via the Font pushbutton. To
select a Boolean point, click on the Browse pushbutton and click on a point from the displayed list.
The Select Required Item dialog is displayed, as illustrated below:
Release 1.2
Page 57
CHAPTER 4 – Objects
OMRON
Only viable points can be viewed from a Select Required Item dialog. The list of items in the Point
Names: field can be refined by selecting an option from the Group: field. Click the OK pushbutton
to accept the new point or click the Cancel pushbutton to leave the point unchanged. Clicking the
Add Point pushbutton or Add Alias pushbutton allows a new point or alias to be created prior to
association with the Wizard. An existing point can also be associated with the Wizard by dragging a
point directly from the Point Editor. Refer to chapter 3, Points regarding adding a new point and
dragging from the Point Editor.
Select the Toggle While Pressed field if the value should only be set while the button is pressed (i.e.
the mouse button is held down when the toggle button is clicked). The value has its state toggled and
then set back when the mouse button is released.
The different styles of toggle button are the same as those for pushbuttons. Examples of some of the
different styles of toggle button are illustrated below:
Switch
Blank Toggle
Coloured
In/Out
Rotary
On/Off
The colour of the coloured pushbutton is red by default, but can be changed by using the Palette.
Click the OK pushbutton to accept the new toggle button attributes or click the Cancel pushbutton to
leave the button unchanged.
Page 58
Release 1.2
OMRON
CHAPTER 4 – Objects
Trend Graph
Trend graphs allow the display of data over time. Click the Trend Graph button, then click
or click and drag on the page to insert the graph.
To edit the Trend Graph, double click on it. The Trend Graph Wizard dialog is displayed as follows:
The Wizard allows entry of Configuration Attributes: and assignment of line colours and expressions.
1, 2, 3…
Release 1.2
1.
Enter a title for the graph in the Trend Graph Title: field.
2.
Enter the frequency of data sampling in the Sample Rate: field, in this
example it is every five seconds.
3.
Enter the period displayed by the graph at any one time in the Visible Time
Span: field.
4.
Enter the size of buffer for stored data of samples in the Total Time Span:
field.
5.
Enter the number of samples on the X-axis in the Time Label Every: field.
6.
Click on the background colour and select the required colour from the
palette.
Page 59
CHAPTER 4 – Objects
OMRON
7.
Toggle the Display Time Labels, Display Slider and Value Bar settings as
desired. Enabling the Value Bar allows the graph to be clicked during
runtime to display the data value at that point.
8.
Enter an arithmetic trace expression for each point or select an expression
via a Browse pushbutton. An existing point can also be associated with the
Wizard by dragging the point directly from the Point Editor. See chapter 3,
Points regarding adding a new point and dragging from the Point Editor.
9.
Change the fonts used for the Graph Title, Scale and Time axis via the
appropriate font button. Alternatively, font sizes can be automatically
calculated by selecting the Auto Font Size option.
10. Exit the Wizard by clicking the OK pushbutton to accept the new Trend
Graph attributes, or click Cancel to leave the Trend Graph unchanged.
The units of measurement of time are selected from the associated field.
To select graph scaling, click the Scaling pushbutton; the Trend Graph Scaling dialog box is
displayed as follows:
Configuration Attributes: can be altered by typing over the existing entries. The Style Attributes: can
be amended by clicking on the settings.
For backward compatibility with CX-Supervisor V2.0, it is possible to save trend graph data to disk.
If the Enable Trend Graph Logging Capabilities option is set in the Advanced Settings of the General
Settings on the Project menu, then an Advanced button will be visible on the trend graph wizard.
This shows the advanced settings used to capture trend graph logging:
Page 60
Release 1.2
OMRON
CHAPTER 4 – Objects
Exit the Trend Graph Scaling dialog by clicking the OK pushbutton to accept the scaling attributes,
or click the Cancel push button to leave unchanged.
An example of a trend graph is illustrated as follows:
Web Browser Object
The Web Browser object allows web files, like HTML JPG or AVI files to be added to a
CX-Supervisor page. These files may be stored locally, on a File Server or be distributed
from any Web Server. The Web Browser object includes a Java Virtual Machine (JVM) allowing
execution of Java Script and Java Applets. Double click the object to show the property page, and
enter the file to be displayed either as a filename, or a fully qualified URL, for example with http:
prefix.
Manipulating Objects
Once inserted, objects can be manipulated to give the required results. An object must be selected
before it can be manipulated.
Select
To select an object, either click on it with the left mouse button or select it from the object
identification control, (for further details on this control refer to chapter 1, Graphics Editor). Eight
“grab handles” are displayed around the object.
To select several objects within a rectangular area, use a rubber band by clicking the left mouse
button and dragging over an area, as illustrated below:
Release 1.2
Page 61
CHAPTER 4 – Objects
OMRON
It is also possible to select all the objects a rubber band intersects by holding down the <Ctrl> key
whilst rubber banding a selection, as illustrated below:
Multiple objects can be selected by holding the <Shift> key down and clicking on each object in turn.
Objects can also be de-selected in similar fashion. Grab handles are displayed for each selected
object.
The most recent object to be selected from the group is denoted by its green grab handles, all other
grab handles are cyan. The co-ordinates of the most recent selection are displayed in the status bar.
All objects can be selected by clicking Select All from the Edit menu.
Move
To move an object or a number of objects, select them and click and hold the left mouse button
within the selection, the object(s) can now be ‘dragged’ to their new location.
Cut
Where objects are to be moved between pages, it is often useful to cut them without having to insert a
new object. CX-Supervisor has the ability to cut and paste objects. Objects which are cut and pasted
retain the properties assigned to them, for example animation or alarms.
To cut an object from the current page, select it and click the Cut button on the toolbar.
The object is removed from the page and is held on the “clipboard” until a new object is cut or
copied.
Copy
An object which is to appear on a number of pages can be copied from an original. To copy
an object, select it then click the Copy button on the toolbar.
A copy of the object is held on the clipboard, overwriting the previously copied or cut object.
Paste
To paste an object which has been cut or copied to the clipboard, click the Paste button on
the toolbar.
The object currently on the clipboard is pasted, either over the original if the object is to remain on
the same page, or positioned in a new page. Objects can then be re-positioned by selecting and
dragging using the mouse.
Page 62
Release 1.2
OMRON
CHAPTER 4 – Objects
Delete
To delete an object or objects, select them and press the <Delete> key on the keyboard.
Undo
The Undo button on the toolbar allows the most recent action (or actions) to be undone. To
undo the action, click the Undo button on the toolbar.
The number of undo operations stored by CX-Supervisor for retrieval can be amended from the
Preferences option on the File menu. This is especially useful when constructing complex pages.
Mirror Image
There are various ways of mirroring objects:
•
Via the Mirror Horizontal and Mirror Vertical buttons on the toolbar.
•
By selecting Mirror from the Edit menu and clicking on either Horizontal or Vertical.
•
By clicking on a grab handle and dragging it across the opposite side
Some objects like Text and Control Objects cannot be mirrored. For further details of mirroring
objects refer to chapter 1, Graphics Editor.
Orientation
Lines, Rectangles, Polygons and Polylines can be rotated. To rotate an object, click the
Rotate button on the toolbar.
The Rotate Object dialog is displayed:
Enter the angle of rotation in degrees in the value entry box and click the OK pushbutton.
Transparency
Solid shapes, polygons and text boxes can be filled with colours and patterns from the tools
palette. When they are created solid objects are filled with the colour already selected on the
palette. Further details on transparency are contained in chapter 1, Graphics Editor.
Group
When there are a number of objects together they can be moved around in a group, keeping their
relative position.
Release 1.2
Page 63
CHAPTER 4 – Objects
OMRON
To group a number of objects, select them, activate the Edit menu and click on Group.
The selection is now regarded as one group with eight “grab handles” for the group rather than eight
for each object; the objects can now be moved together.
Once objects have been grouped they can be ungrouped by selecting the object, activating the Edit
menu and clicking on Ungroup.
Raise and Lower
Each new object inserted on a page is placed on top of the previous one. Although they may
appear to be on the same level, objects can overlap, so it may be necessary to ‘raise’ an
object so that it appears over the top of another object. For further details on raising and
lowering objects refer to chapter 1, Graphics Editor.
Alignment
Objects inserted on a page can look messy unless they are aligned relative to each other. CXSupervisor helps by allowing the contents of a page to align on a grid. The grid can be turned on and
off as required.
There are a number of different grid sizes available: 4, 8, 16, 32 and 64 pixels. The Snap To Grid
function snaps to the nearest grid.
To align page objects and view a grid, select Grid from the View menu.
Select the required grid size or click on Snap to Grid to align the most recently entered objects on the
chosen grid. The grid can be turned off by selecting Off.
An example of the use of the grid is illustrated as follows:
In this example, the selected polyline is in the process of being moved down. The presence of the
grid governs the movement of the object in all directions. As the object is moved, its position
“snaps” an equal distance from the original position of the object against the grid. Currently, the
object has been moved five grid steps down (shown by the bracket).
Alignment Toolbox
Objects on a page can be aligned in a variety of ways using the Alignment toolbar.
It is possible to:
Page 64
Release 1.2
OMRON
CHAPTER 4 – Objects
Click the Centre Horizontally on Page button from the toolbar to centre objects on a page
horizontally.
Click the Centre Vertically on Page button from the toolbar to centre objects on a page
vertically.
Click the Left Alignment button from the toolbar to align objects along their left edge.
Click the Right Alignment button from the toolbar to align objects along their right edge.
Click the Top Alignment button from the toolbar to align objects along their top edge.
Click the Bottom Alignment button from the toolbar to align objects along their bottom
edge.
Click the Centre Align Horizontal button from the toolbar to align objects on their
horizontal centres.
Click the Centre Align Vertical button from the toolbar to align objects on their vertical
centres.
Click the Make Same Width button from the toolbar to make objects the same width
Click the Make Same Height button from the toolbar to make objects the same height.
Click the Make Same Height and Width button from the toolbar to make objects the same
width and height.
Click the Align to Grid button from the toolbar to align objects to the grid.
When performing alignment operations, the Master Object determines how the other objects are
aligned. The Master Object, i.e. the last object clicked on, has green sizing handles.
To align objects:
1, 2, 3…
1.
Select the objects to be aligned.
2.
Ensure the correct master object is selected.
3.
Choose the appropriate tool from the Alignment toolbar.
The alignment operations available at any one time vary according to the number of objects selected.
Zoom
It is often useful to be able to view an object in more detail. The Zoom option allows selected objects
to be magnified up to four times their normal size.
To enlarge an area of the screen, choose the View menu and select Zoom. Then select the required
magnification factor: Off, 2× or 4.
A specific object can be zoomed in on by selecting that object and then performing the procedures
described above.
Release 1.2
Page 65
CHAPTER 4 – Objects
OMRON
Applying Tooltips
In the runtime environment, it is possible to provide instant help for the object currently selected by
the cursor. This is achieved by tooltips that can be applied to all objects.
1, 2, 3…
1.
In the development environment, select the object to apply a tooltip.
2.
Click on Tooltip Text from the Edit menu. The Tooltip Text is displayed.
3.
Type the help text in the Tooltip text: field or select the Browse pushbutton
to apply the value of a point.
4.
Click the OK pushbutton to accept the settings or the Cancel pushbutton to
abort the operation.
An example of a tooltip in the runtime environment is as follows:
Using the Floating Menu
Clicking the right mouse button within CX-Supervisor brings up a context-sensitive menu known as
the Floating menu. There are two such menus, one in the development environment and one in the
runtime environment. The development environment Floating menu contains short-cuts for many
operations discussed in this chapter.
Page 66
Release 1.2
OMRON
CHAPTER 5 – ActiveX Objects
CHAPTER 5
ActiveX Objects
This chapter describes the process of using ActiveX objects within CX-Supervisor applications.
Overview
The Microsoft Windows ActiveX technology allows objects called ‘components’ to be developed,
and are used by inserting them into an ActiveX container, like CX-Supervisor. ActiveX components
may perform many different functions, which can be graphical or non-graphical, but they follow
standard rules for defining their Properties, Methods and Events. Properties are like settings, for
example a control’s colour would be a property. Methods are like functions or actions that can be
called for example a control might support a Redraw method. Events are actions the control may
create, like OnLeftClick. Following these standard rules allows any ActiveX control from any
manufacturer to work in any container.
Inserting a new object
A new ActiveX control may be inserted on the page as follows:
1, 2, 3…
Release 1.2
1.
Click on the page in which the object is to be inserted.
2.
Click the Insert ActiveX Object button.
displayed:
3.
Select the control you wish to insert from the list.
The Insert Object dialog is
Page 67
CHAPTER 5 – ActiveX Objects
OMRON
Editing Properties at Design Time
The properties of ActiveX objects can be edited during the design stage using the following
procedure:
1, 2, 3…
Page 68
1.
Open the ActiveX Property Browser by clicking the ActiveX Property
Browser button in the toolbar or by selecting the ActiveX Property Browser
option from the Utilities menu.
2.
With the ActiveX Property Browser displayed select the appropriate
ActiveX control. This will list the full range of property names available
for that control in the browser, and their values.
3.
The Value of each Name can be changed as required by clicking in the
value box and entering the new value. Some options require you to enter
specific information, others provide a choice of entries from a drop down
menu.
4.
To edit the values of other ActiveX controls simply click on the control to
select it. The values of the previous object will be replaced with those of
the new selection.
Release 1.2
OMRON
CHAPTER 5 – ActiveX Objects
In addition to editing properties with the Property Browser, many ActiveX controls support their own custom
Property Pages. These may be accessed in design time by either double clicking the control, or right clicking
the control and selecting Properties from the Object’s popup menu:
Release 1.2
Page 69
CHAPTER 5 – ActiveX Objects
OMRON
Reading and Writing Properties at Run Time
ActiveX properties can be read and written at runtime, for example to change values or colours as
required. This can be achieved using the CX-Supervisor script functions GetProperty and
PutProperty, or alternatively in VBScript using the normal dot syntax for example
@VBSCRIPT
Display1.Value = 100
@ENDIF
For more details see the CX-Supervisor Script Language Reference Manual.
Calling Methods at Run Time
ActiveX methods can also be called at runtime. This is achieved by using the Supervisor script
function Execute or alternatively in VBScript using the normal dot syntax for example
@VBSCRIPT
CommonDialog1.ShowOpen
@ENDIF
Again for more details see the CX-Supervisor Script Language Reference Manual.
Responding to Events
Some ActiveX components are written to generate events on certain conditions, like mouse clicking
or user input or error conditions. You can write a script to execute whenever any event occurs. These
scripts are defined as subroutines in the page initialisation script as they may be called any time the
page is open. To easily add these subroutines, from the ActiveX property browser, click the ‘Events’
tab. This shows all the event types for this control and any parameters the event may pass, for
example the code number of the key pressed. Select the event name to add or edit the script for, and
click the square edit button.
Page 70
Release 1.2
OMRON
Note:
Release 1.2
CHAPTER 5 – ActiveX Objects
In previous versions Event scripts could be added from the Animation Editor but the method
above provides more efficiency as all event scripts are loaded just once on page
initialisation.
Page 71
OMRON
CHAPTER 6 – Projects
CHAPTER 6
Projects
This chapter describes the concept of projects. It details procedures for creating and amending
projects, and the process of associating users with projects. It also deals with the process of
compiling a project.
Overview
A CX-Supervisor application consists of a number of pages linked together. The pages may contain
passive or active graphics, text or animations, and may be grouped together logically to form a
project. A project may consist of many pages, or simply a single page. Projects may be built and
tested within the CX-Supervisor development environment, and run “stand-alone” under the CXSupervisor run-time environment.
Only one project at a time may be open for editing within the CX-Supervisor development
environment. An attempt to open a second project forces CX-Supervisor to close the current project
(prompting to save changes where there is unsaved information), and open the second project.
Creating a Project
To create a new project within CX-Supervisor, select New from the Project menu.
CX-Supervisor displays the following dialog:
Release 1.2
Page 73
CHAPTER 6 – Projects
1, 2, 3…
OMRON
1.
Locate the parent directory in which the project directory is to reside using
the Folder: and Drives: fields.
2.
Enter a name for the project directory in the New Project Folder: field. If a
name is entered, the folder is created and used; otherwise the selected
folder is used. The directory name must be no more than 8 characters and
may only contain characters valid for use in MS-DOS file names.
3.
Enter a name for the project in the Project Name: field. The project name
must be no more than 8 characters and may only contain characters valid
for use in DOS file names.
4.
Click the OK pushbutton on the New Project dialog to create the project.
Alternatively, click the Project Info pushbutton to open the Project Information dialog, and enter a
title and some descriptive text for the new project. For details of using the Project Information dialog
refer to chapter 6, Project Information. Click the OK pushbutton on the New Project dialog to create
the project.
Note:
If the PC installation of CX-Supervisor is on a networked machine, a Network
pushbutton is added to the dialog. For further information on the function of the
Network dialog, refer to the Microsoft Windows User Guide.
Amending a Project
To amend an existing project it must first be opened (assuming it is not already open). To open a
project select Open from the Project menu. CX-Supervisor displays the Open dialog. This is a
standard Windows dialog and usage depends on your operating system. Please consult your
Microsoft documentation
1, 2, 3…
1.
Locate the drive and directory where the desired project is stored.
2.
Select the desired project from the list presented.
3.
Click the Open pushbutton to load the project.
Once the project is loaded, the various editing tasks required may be carried out (such as editing page
or graphics formats), as described in the other chapters of this manual.
Saving a Project
Once a project has been created it is wise to save it. It is good practice to ensure that projects are
saved regularly, in case of an event such as a power failure. To save a project, select Save from the
Project menu.
If this is the first time the project has been saved, the Save As dialog is displayed.
1, 2, 3…
Page 74
1.
Move to the location where the project is to be stored.
Release 1.2
OMRON
CHAPTER 6 – Projects
Note:
2.
Ensure that the Save as Type: field is set to CX-Supervisor Projects
(*.SCS).
3.
Enter a name for the project. The name under which the project was
created is offered as a default.
4.
Click the Save pushbutton to save the project.
Subsequent saves do not cause the Save Project As dialog to be displayed.
Printing a Project
All of the printable views of the project can be printed together, including page layouts and all
scripts. This can be useful as a development aid, for maintenance and for project documentation.
1, 2, 3…
1.
Start CX-Supervisor and load the project to be printed.
2.
From the options dialog, select the items to print and press OK.
3.
Select the printer to print to and press OK.
Device Configuration
To amend the device configuration or create connections to a PLC or temperature controller,
click the Device Setup button from the toolbar. This results in the Setup Devices dialog
being displayed.
Creating a PLC Connection
A new device can be added by clicking on the Add pushbutton on the Setup Devices dialog.
Release 1.2
Page 75
CHAPTER 6 – Projects
Note:
OMRON
CX-Supervisor calls an external application to change PLC information. The
functions described in the following paragraphs may differ slightly depending
upon which application and version has been invoked.
A name can be assigned for the device in the PLC Name field.
Select the PLC from the Device Type: field. To add a temperature controller, select a temperature
controller from the Device Type: field, e.g. E5AF-AH. See also Chapter 14 for details on other
models.
Clicking the Setup pushbutton results in the Device Type Settings dialog being displayed allowing
the device type of the PLC to be configured.
Page 76
Release 1.2
OMRON
CHAPTER 6 – Projects
Note:
The possible settings for PLC configuration depend upon the type of PLC
selected (this applies also to the Read Only and Timer/Clock fields).
On completion, click the OK pushbutton to continue, or the Cancel pushbutton to abort the
operation. Values specified may be set as default by clicking the Make Default pushbutton.
A network may be specified for the selected PLC, by selecting from the Network: field. The
networks available are dependent on the device type selected.
Clicking the Setup pushbutton results in the Network Settings dialog being displayed.
The Unit Number is the identifier for the network being configured.
The Destination Network Address and Destination Node Number identify the connection point to the
network.
A PLC can be selected to act as a gateway to the PLC being edited; this list is restricted to the PLCs
contained in the current project.
Selecting the Driver tab results in the Driver Configuration view being displayed; this part of the
Network Settings dialog helps to ensure that data is transmitted correctly over the network.
Release 1.2
Page 77
CHAPTER 6 – Projects
Note:
OMRON
The possible settings for the Baud Rate, Parity, Data Bits, and Stop Bits fields
depend upon the port selected.
If a timeout occurs, the communication is not complete. Where necessary, increase the Timeout
Offset value (in milliseconds) to ensure that the device does not cause a timeout.
Values specified may be set as default by clicking the Make Default pushbutton.
Modifying a PLC Connection
From the Setup Devices dialog, a PLC name may be modified by selecting the PLC name from the
Device List on the Setup Devices dialog, and clicking the Modify pushbutton. This results in the
Change PLC dialog being displayed.
Page 78
Release 1.2
OMRON
CHAPTER 6 – Projects
A new name can be entered in the PLC Name: field. If an invalid PLC name is entered, an error
message is displayed on clicking the OK pushbutton.
Removing a PLC Connection
From the Setup Devices dialog, a PLC name may be removed from the PLC Name: field by selecting
the PLC name from the Device List on the Setup Devices dialog, and clicking the Delete pushbutton.
This results in a confirmation dialog being displayed. Click the Yes pushbutton to remove the PLC
from the list, or the No pushbutton to abort the delete operation.
Note:
A PLC cannot be renamed, deleted or edited if it is currently open for
communications.
Accessing PLC Connection in Runtime
It is possible to reconfigure PLCs at runtime via the right mouse button floating menu option PLC
Maintenance List. The list of currently configured PLCs is displayed via the PLCs in Project dialog
box. On selection of a PLC, the PLC Information dialog is displayed, which allows the user to
change the PLC configuration dynamically during runtime.
The Open PLC option provides the capability to toggle the communications status of the PLC.
The PLC Mode options switch the current mode of operation of the PLC between Stop, Debug,
Monitor and Run.
♦
Stop mode halts the PLC program execution allowing the PLC to be programmed.
♦
Debug mode allows for the single stepping of program execution. This mode is reserved for CVseries PLCs only.
♦
Monitor mode operation allows normal PLC program execution and modification of data.
♦
Run mode operation allows normal PLC program execution. No data in any of the PLC memory
areas can be changed.
It is possible to individually enable / disable point communications from the PLC Maintenance
dialog.
Release 1.2
Page 79
CHAPTER 6 – Projects
OMRON
Selection of the Communication Settings option displays the Communication Settings dialog,
showing the current settings for the PLC:
Page 80
Release 1.2
OMRON
CHAPTER 6 – Projects
It is possible to configure default settings for the runtime via the PLC Runtime Default Settings fields
in the Setup PLCs dialog.
Communications to the PLC can be enabled on startup via the Open PLC option.
Settings
General Settings
Colour Palette
A specific set of colours may be defined for use within a project. This may include a maximum of 66
unique colours. To adjust the colours, select General Settings from the Projects menu, and select
Colour Palette from the sub-menu.
CX-Supervisor displays the following dialog:
1, 2, 3…
Release 1.2
1.
Select the coloured square which requires editing.
2.
Adjust its colour values using the Red, Blue and Green sliders.
3.
When the desired colour has been created, enter a name in the Colour
Name: field.
4.
Click the OK pushbutton when all colours requiring editing have been
edited.
Note:
The mixing of colours on screen differs from the mixing of, for example, colour
paint. Under normal circumstances, the more of a colour which is added to a mix,
the darker it gets. The opposite is the case for mixing colours on screen, i.e. Black
consists of no Red, no Green and no Blue, whilst White consists of full Red, full
Green and full Blue.
Note:
The first sixteen colours cannot be mixed.
Page 81
CHAPTER 6 – Projects
Note:
OMRON
Using a 16 colour-based screen resolution (consult the Microsoft Windows
documentation for further information) the seventeenth colour onwards are dithered
from the sixteen base colours. Higher colour-based resolutions are not dithered.
Default Button Font
The Default Button Font option, which can also be selected from the General Settings sub-menu of
the Project menu, displays the standard font dialog:
This dialog is used to set the default font specification to be used for all text displayed on push
buttons created using the graphics editor. Any button can also have its font changed from the default,
using the relevant Wizard in the graphics editor. See chapter 4, Objects.
Runtime Settings
The Runtime Settings option is selected from the Project menu.
The settings discussed in the following paragraphs help to configure runtime environment
applications and have no effect in the development environment. Settings that affect the development
environment are discussed in chapter 2, Pages.
Startup Conditions
To open the Startup Conditions dialog, select Startup Conditions from the Runtime Settings menu.
The dialog is displayed as follows:
Page 82
Release 1.2
OMRON
CHAPTER 6 – Projects
Click the settings to enable/disable General Startup Conditions and Communication Startup
Conditions. Click the OK pushbutton to accept the settings or the Cancel pushbutton to abort.
When Keyboard Control is enabled, a focus rectangle becomes visible around the currently selected
object. The cursor keys and <Tab> key can then be used to navigate around the selectable objects on
a page. Once an object is selected certain actions can then be applied, depending on the object’s type.
The most common action is to simulate a left mouse button click.
The following list shows all the possible facilities with Keyboard Control enabled.
♦
Moving Around Selectable Objects Using Cursor Keys. The cursor keys can be used to move
around the objects in the respective direction.
♦
With an object selected, if the right cursor key is pressed, then the closest object is selected from
within an area bounded by lines drawn diagonally upwards and diagonally downwards (and to
the right) from the centre of the object. If no object is found then the current object remains
selected. A similar rule also applies when using the left cursor key, and the up and down cursor
keys.
Note: Selectable items must have a left mouse button event defined or have a default action.
♦
Moving Around Selectable Objects Using <Tab> Key. The <Tab> key can be used to move
around all the objects in the order in which they are drawn (this can be varied using the ‘raise
object’ and ‘lower object’ editing facilities). The <Shift>+<Tab> key can be used to move
around the objects in the reverse order.
♦
To select items in a specific tab order: use the <Tab> key to move around the page items in a
specific order, using the ‘move to top’ feature. Start at object number 1 and end with the last
object, i.e. if obj1, obj2 and obj3 then use ‘move to top’ on obj1 first, followed by obj2 and then
by obj3; this gives the tab order obj1, obj2, obj3.
♦
Changing Between Pages. The <Ctrl>+<Tab> key can be used to change between pages.
Release 1.2
Page 83
CHAPTER 6 – Projects
OMRON
♦
Simulating a Left Mouse Button Click. Objects that have scripts attached (such as a pushbutton)
or objects that perform a particular action when clicked (such as toggle buttons) can be executed
by using the <Enter> key.
♦
Slider Operation. When a slider object is selected, the plus (+) and minus (-) keys can be used to
increment or decrement its value respectively. This also applies to the sliders on trend graphs.
♦
Obtaining the Runtime Floating Menu. To display the Runtime Floating menu, use either the
<Shift>+<F10> key combination or use the Windows 95 right mouse button key, which is next
to the <Ctrl> key on the right hand side of the keyboard.
♦
Standard Windows Keys. Some standard Windows key combinations are as follows:
<Alt>+<-> (hyphen)
Used to access the child window control box at the top left
hand side of the dialog.
<Alt>+<Spacebar>
Used to access the main window control box at the top left
hand side of the dialog.
<Alt>+<F4>
Used to close down the current application.
♦
Using Runtime Alarm, Error and Recipe Viewer. These can be invoked from the Runtime
Floating menu (see above). To access their functionality use the <Tab> key to move from
toolbar button to toolbar button, and <Enter> to press a button. The up and down cursor keys
can be used to scroll the displayed list. To close them (or to move or resize them) use the
standard <Alt>+<-> (hyphen) key combination to access their menus.
♦
Other Notes. In Project level scripts, it is possible to define ‘OnKeyPress’ scripts, which are
attached to the cursor keys. If Keyboard Only operation is set, then it is not possible to execute a
script attached to one of the cursor keys, since they are being used for navigating around the
selectable objects on the page. Alternative additional keys have been added to compensate for
this. They are the number pad cursor keys (i.e. 2, 4, 6, and 8). However, these can only be used
when the <Num Lock> key is on.
Non-Volatile Rate
The Non-Volatile rate specifies how often the value of points flagged as ‘non-volatile’ are saved to
disk, in seconds. The latest disk values are used to re-initialise the point values when CX-Supervisor
is restarted. To adjust this value select Runtime Settings from the Projects menu, and select
Non-Volatile Rate from the sub-menu. CX-Supervisor displays the following dialog:
Enter a new value for the Non-Volatile Rate in the Seconds field and click the OK pushbutton.
Page 84
Release 1.2
OMRON
CHAPTER 6 – Projects
Screen Size
To open the Screen Size dialog, select Screen Size from the Runtime Settings menu. The dialog is
displayed as follows:
Type valid values into the Screen Width: and Screen Height: fields. These values are used to define
the screen size of the runtime application, but do not affect Maximise and Minimise dialog states. By
enabling the Rescale run-time to screen size option the screen rescales itself to take into account the
resolution of the runtime system. Click the OK pushbutton to accept the setting or the Cancel
pushbutton to abort.
Alarm Settings
To open the Alarm Settings dialog select Alarm Settings from the Runtime Settings menu. The dialog
is displayed as follows:
Release 1.2
Page 85
CHAPTER 6 – Projects
OMRON
In the On Alarm Automatically Display area set the Alarm Status Viewer and Alarm History Viewer
settings as required. When these options are set, the Current Alarms viewer or Alarm History viewer
(respectively) is automatically displayed in runtime when an alarm occurs.
Set the Maximum entries in Status Viewer and Maximum entries in History Log fields to the desired
values. The numbers specify how many messages are displayed in the respective viewer dialogs in
runtime. Select the Log system start/stop messages setting to ON if required.
Note:
If more messages exist than are requested to be displayed, the most recent
messages are displayed in preference to older messages.
The values shown above are sensible defaults.
In the Alarm Status Messages area, if the User Defined Text option is set, default messages for Raised
Text, Cleared Text, Acknowledge Text, and Auto Acknowledge Text can be applied. If the Use
Language File Text option is set, the alarm status messages default to the supplied language file.
The Alarm Sound pushbutton allows the selection of an audible warning which may be played when
an alarm occurs in runtime. The Open Waveform File dialog is shown below:
Note:
If the PC installation of CX-Supervisor is on a networked machine, a Network
pushbutton is added to the dialog. For further information of the function of the
Network dialog, refer to the Microsoft Windows User Guide.
Alarm/Message Printer Settings
To open the Alarm/Message Printer Settings dialog select Alarm/Message Printer Settings from the
Runtime Settings menu. The dialog is displayed as follows:
Page 86
Release 1.2
OMRON
CHAPTER 6 – Projects
1, 2, 3…
1.
Select the target printer in the Printer Name: field.
2.
If the printer type is a Page Printer, ensure the Page Printer setting is set
‘ON’ and the appropriate number of lines per page are specified in the
Number of Lines Per Page: field.
3.
Specify a Line Terminator: setting, either CR (Carriage Return), LF
(Line Feed) or CR + LF.
4.
Click the OK pushbutton to accept the changes, or the Cancel
pushbutton to abort.
Event/Error Messages
To open the Event/Error Settings dialog select Event/Error Settings from the Runtime Settings menu.
The dialog is displayed as follows:
Set the Maximum entries in Event/Error field and the Automatically Display Event/Error Log on:
options as desired. Click the OK pushbutton to accept the changes, or the Cancel pushbutton to
abort.
In the runtime environment, the Event/Error Log dialog can be displayed at any time.
Release 1.2
Page 87
CHAPTER 6 – Projects
OMRON
The events can be sorted, based on a designated field type: date, time, reported by, priority or
associated message. By selecting the Date field, the events are sorted alphanumerically by date. The
Time, Reported by, Pri/Event and Message fields react in the same way. The Event/Error Log display
shows the log listed in date order.
The widths of the alarm fields can be widened or narrowed as required using the mouse
to drag the column boundaries.
There are a number of toolbar buttons that aid the use of the Event/Error Log.
The Disable Error Updates button, once pressed, stops further events occurring in the
runtime environment being added to the log. The Event/Error Log dialog is still
accessible to switch back subsequently.
The Enable Column Sorting button allows the format of the Error/Event Log dialog to
be continually updated when subsequent errors or events are added.
The Clear Event/Error Log button clears all entries from the log.
The Display All Errors/Events button lists all events and errors irrespective of priority.
The list is sorted according to the Date, Time, Reported by, Pri/Event or Message field.
The Low Priority button lists all errors designated as a low priority only. Other errors
and events are not deleted from the log; they are merely not visible.
The Medium Priority button lists all errors designated as a medium priority only.
Other errors and events are not deleted from the log; they are merely not visible.
The High Priority button lists all errors designated as a high priority only. Other errors
and events are not deleted from the log; they are merely not visible.
The Events button lists all events. Errors, of all priorities, are not deleted from the log;
they are merely not visible. Examples of events are system startup, system shutdown
Page 88
Release 1.2
OMRON
CHAPTER 6 – Projects
and user security notices.
The Print button prints the current contents of the error and event log. Ensure that the
printer is correctly set up before printing.
The Error Information Dialog button, once pressed, displays a summary of error
information, including a detailed count of errors and PLC communication information.
Click the Close pushbutton to remove this dialog.
Language Settings
The language for user-defined text can be set via the Language Settings dialog. Select Runtime
Settings from the Projects menu, followed by Language Settings to display the Language Settings
dialog.
Release 1.2
Page 89
CHAPTER 6 – Projects
OMRON
Select a language from the Language for User-Defined Text: field. Click the OK pushbutton to
accept the settings, or the Cancel pushbutton to abort the operation.
Point Substitution Settings
The enclosing characters associated with a report can be changed via the Point Substitution Settings
dialog. Once set, these characters must be fixed for all reports generated by the project. Select
Runtime Settings from the Projects menu, followed by Point Substitution Settings to display the Point
Substitution Settings dialog.
Supply enclosing characters in the Opening Characters: field and Closing Characters: field. Click
the OK pushbutton to accept the settings, or the Cancel pushbutton to abort the operation.
Advanced Settings
To open the Advanced Settings dialog select Advanced Settings from the Runtime Settings menu.
The dialog is displayed as follows:
Page 90
Release 1.2
OMRON
CHAPTER 6 – Projects
Click the settings to enable/disable Internal Communication Optimisations and Communication
‘Packet’ Optimisations.
Bad Quality values, and results of calculations using bad quality values can be shown as ‘#’
characters. This could indicate a communication failure, or Bad Quality status in an OPC Server.
Click the OK pushbutton to accept the settings or the Cancel pushbutton to abort.
Runtime Security
Configured Users
In a runtime application, it is possible to apply security measures in the development environment so
that only sufficiently privileged users of the runtime application can access certain elements. It is
also possible to housekeep security information within the runtime environment, with privileged
users able to add, amend or remove users.
There are four levels of user privilege available in CX-Supervisor:
♦
Operator level privilege.
♦
Supervisor level privilege.
♦
Manager level privilege.
♦ Designer level privilege.
User configuration in the development environment is handled by the Configured Users dialog.
Select Configured Users from the Runtime Security menu.
The Configured Users dialog is displayed as follows:
Release 1.2
Page 91
CHAPTER 6 – Projects
OMRON
By default, there are four previously defined users listed in the Configured Users: field: Designer
with designer-level privileges, Manager with manager-level privileges, Operator with operator-level
privileges and Supervisor with supervisor-level privileges.
To add a new user:
1, 2, 3…
1.
Click the Add pushbutton. The User Attributes: fields and buttons become
enabled, and the contents of all fields are cleared, ready for a new user to be
added.
2.
Type the full name of the new user in the Full Name: field.
3.
Type a login name in the Login Name: field.
4.
Type a user password in the Password: field. The password must be at
least four characters in length.
5.
Select a level of privilege from the Security Level: drop down list.
6.
Click the Store pushbutton to add the new user to the Configured Users:
list, or the Cancel pushbutton to abort the operation.
To modify an existing user:
1, 2, 3…
1.
Select a user from the Configured Users: list and click the Modify
pushbutton. The User Attributes: fields and buttons become enabled, with
the contents of all the fields filled with the attributes of the selected user.
2.
Amend the full name, login name, password and level of privilege in the
same way as adding a new user.
3.
Click the Store pushbutton to update the user in the Configured Users: list,
or the Cancel pushbutton to abort the operation.
To remove a user from the Configured Users: list:
1, 2, 3…
1.
Select a user from the Configured Users: list and click the Delete
pushbutton.
2.
A confirmation dialog is displayed. Click the Yes pushbutton to remove
the selected user or the No pushbutton to abort the operation.
When all user amendments are complete, click the Close pushbutton.
In the runtime application, to make use of the designated privilege, the user must log in. Login can
be accessed in a variety of ways, and so is dependent on the setup of the runtime application. Some
applications may require login as soon as the application is run, others may allow login from a
context-sensitive floating menu. Refer chapter 9, Animation for further information. The Login User
dialog is as follows:
Page 92
Release 1.2
OMRON
CHAPTER 6 – Projects
To log in, enter the login name (not the full name) in the Login Name: field and the associated
password in the Password: field. Any characters typed in the Password: field are disguised by a ‘*’
symbol for each character typed. Click the OK pushbutton to log in or the Cancel pushbutton to
abort.
For users without a keyboard to enter login details, select the Keyboard pushbutton. The login name
and password can be constructed from the subsequent dialog by clicking on each pushbutton in turn,
followed by the Enter pushbutton to complete.
A user can detach from specialised user privileges by logging out. Access is again dependant on the
application. There is no dialog associated with logout; once logout is activated privileges are
immediately discontinued. Whilst one user is logged in, it is possible for a different user to log in, as
prior to login, the current user is automatically logged-out by CX-Supervisor.
A user with the designer privilege can further amend the user configuration in the runtime
environment using a similar dialog to the development environment’s Configured Users dialog. As
well as typing a password, verification of the password is required, and both fields are disguised by a
‘*’ symbol. This is so that a new user can apply their own password, and that only they know the
password. Verification is required to ensure the password was typed correctly in the first instance.
Menu Option Access Levels
To open the Menu Option Access Levels dialog select Menu Option Access Levels from the Runtime
Security menu. The dialog is displayed as follows:
Release 1.2
Page 93
CHAPTER 6 – Projects
OMRON
As well as a context-sensitive floating menu for the development environment, there is a floating
menu for the runtime environment which is configurable in the development environment. It is
possible to select the operations to be on the runtime floating menu, by clicking the relevant setting
across the three tabs General, Utilities and Communications. It is also possible to assign a level of
user privilege to the menu, so each level of user sees a different floating menu. This is achieved by
selecting a user privilege from the relative drop down list. The Communications tab permits the
activation of CX-Server components such as the PLC Data Trace and PLC Memory Card
components. Refer to the CX-Server Reference Manual for further information on CX-Server
components.
On completion, click the OK pushbutton to accept changes or the Cancel pushbutton to abort.
Exit Level
An additional security measure can be applied by selecting Exit Level from the Runtime Security
menu. The Exit Level dialog is displayed as follows:
The dialog allows a specific privilege to be applied to exiting the runtime application. Select a user
privilege from the drop down list and click the OK pushbutton to confirm the setting or the Cancel
pushbutton to abort.
Page 94
Release 1.2
OMRON
CHAPTER 6 – Projects
Compiling and Running a Project
When a project is running it cannot be edited. CX-Supervisor runs projects under the CX-Supervisor
runtime environment.
To run the current project, click on the Run button on the toolbar.
The CX-Supervisor runtime environment starts, and automatically runs the project in a
separate dialog which is given the name of the project. It allows examination of project
alarm details and the run history.
Save Runtime As
Once the project has been compiled and run, the compiled version of the project may be saved into
another directory location or onto another disc for issue to the target equipment. CX-Supervisor asks
for a location and name for the runtime project. This is a standard Windows dialog and operation
depends on your operating system. Please consult your Microsoft documentation for full details. The
default file type is *.SR2.
Create Runtime Install Disk
A CX-Supervisor application can be packaged safely for authorised distribution by creating a runtime
install disk. The process copies all required files, plus files to install to the specific directory e.g.
“A:\” to be used to distribute the runtime project.
Click on Create Runtime Install Disc from the Project menu. The Save Runtime As dialog is
displayed ready to create an installation to the floppy drive. Ensure a diskette is inserted into the
floppy drive. Refer to chapter 6, Save Runtime As for further information regarding the Save
Runtime As dialog.
Note:
The files are not compressed. This feature does not support large projects that need
to span multiple disks.
Note:
The Runtime environment itself is not copied and must be installed from a
legitimate source
Note:
ActiveX components used are not copied and should be installed on the target
machine using the supplier’s instructions.
Project Information
Information may be stored concerning a project, by using the Project Information dialog. This dialog
may be accessed, either when a project is first created, from the New Project dialog, or by selecting
Information from the Project menu.
CX-Supervisor displays the following dialog:
Release 1.2
Page 95
CHAPTER 6 – Projects
OMRON
Enter a title and any relevant details concerning the project in the Title: and Description: fields, and
click the OK pushbutton.
Alias Definitions
An alias definition can be provided to replace strings in scripts and expressions used throughout CXSupervisor applications. An associated string replaces the alias when used in a script or expression.
Select Alias Definitions from the Project menu.
The 3 columns are seperated by tabs and are the Alias text to be used, the actual value to be used and
an optional comment, (starting with ‘ character) respectively
Find
The project can be searched to find occurrences of text or a point name. It can also be used to search
for text within script e.g. to find where a text message is generated from.
Page 96
Release 1.2
OMRON
CHAPTER 6 – Projects
The areas which can be searched are:
♦
The current page.
♦
All pages.
♦
Project scripts.
♦
Alarms.
♦
Recipes.
♦ The project, which includes Project scripts, Alarms and Recipes.
By default, all areas are searched i.e. ‘Project and Pages’. To perform a Find operation:
1, 2, 3…
1.
Select the Find button on the toolbar or Find from the Edit menu.
2.
Type the text to find in the Find What field, or select a previous entry from
the drop down list. The Browse pushbutton can be used to select an item.
3.
Select the area to search; Project & Pages searches all areas.
4.
Choose the required options; Output to pane 2 results in pane 1 to be saved
for future use.
5.
Press the Find pushbutton to start the search or the Cancel pushbutton to
abort the operation.
The output dialog shows all occurrences of the text in the selected areas. It illustrates the location
including page name, alarm name, recipe, script name, object, line number and animation as relevant,
followed by the occurrence itself. Double clicking on any line opens the appropriate editor.
Release 1.2
Page 97
CHAPTER 6 – Projects
OMRON
The output can be printed by selecting Print from the right mouse context menu.
Navigating Projects with the Workspace
The Workspace is activated by clicking the Workspace button on the toolbar.
Workspace dialog is displayed:
The
Selecting the Pages, Alarms or Recipes pushbutton displays a list of the associated components that
form part of the project.
Project Editor
The Project Editor is activated by clicking the Project Editor button on the toolbar.
When activated, the Project Editor may be displayed minimised at the bottom of the main
CX-Supervisor window. Double click to view the contents of the Project Editor.
Page 98
Release 1.2
OMRON
CHAPTER 6 – Projects
About the Project Editor
The Project Editor provides a window into the contents of a project. It lists all the pages currently
comprising a project, and allows for pages to be moved into or out of projects. An example of the
Project Editor dialog is shown as follows:
The Project Editor consists of a control bar and a display area. The control bar includes controls to
filter the pages to be displayed, add and remove pages from a project, and open pages.
Viewing the Contents of a Project
The Project Editor is used to view the pages within a project.
Individual listed pages are sorted, based on the designated page name, page path, project status,
runtime display or load status. By selecting the Page Name field, the pages are sorted
alphanumerically by name. The Page Type, Project Status, Runtime Display and Load Status fields,
once selected, react in the same way. The Project Editor display shows the projects listed in page
name order.
The widths of the editor fields can be widened or narrowed as required using the
mouse to drag the column boundaries.
The typeface of the editor can be amended from the Preferences option in the File
menu. This is especially useful when printing.
Opening a Page via the Project Editor
To open pages via the Project Editor, click the Open Page button on the toolbar.
Adding Pages to a Project
When a new page is created, it is automatically registered in the Project Editor but its details
are not saved. When the page is saved as a .PAG file, a message is displayed requiring
confirmation to add this page to the project. Click the Yes pushbutton to add the page or the
Release 1.2
Page 99
CHAPTER 6 – Projects
OMRON
No pushbutton to save the page without adding to the project. If the page was not added to
the project when saving, it can be added later by using the Add Page button on the toolbar.
Removing Pages From a Project
To remove pages from a project, select the page by clicking its description on the Project
Editor and click the Remove Page From Project button on the toolbar. A message is
displayed asking ‘Do you want to remove (name and path of page) from the project?’. Click
the Yes pushbutton to delete the page, or click the No or Cancel pushbutton to keep it and
return to the Project Editor.
Linking Pages in a Project
A number of pages may be linked together within a project. Linking allows a main page containing
active elements (e.g. pushbuttons) to be loaded and depending upon the actions performed (i.e. which
buttons are clicked) allow other pages to be loaded on demand. For further details of showing pages
on demand, refer to chapter 9, Animation.
Selecting Pages for Display on Run
When a project is run the first pages to be displayed can be selected. To display a page when
a project is run, open the Project Editor, select the page by clicking on its description and
click the Display Page Upon Run button on the toolbar.
To stop a page being displayed on run, click the Don’t Display Page Upon Run button on
the Project Editor toolbar.
Changing the View Mode
Select the Large Icons button to view details with large icons.
Select the Small Icons button to view details with normal icons.
Select the List button to view details as a list.
Select the Details button to view details as a list including page name, page path, project
status, runtime display and load status information. The details can be sorted in ascending
order by clicking once or in descending order by clicking twice, in the appropriate field.
Viewing Project Details
To open the Project Details dialog and view the project name and description, click on the
Edit Details About Project button on the Project Editor toolbar.
Page 100
Release 1.2
OMRON
CHAPTER 6 – Projects
Multiple Selection
Standard multiple-selection facilities can be used within the Project Editor. To select an additional
line hold the control key down while clicking; to select all lines between the anchor line (the last line
clicked on) and another line hold the <Shift> key down while clicking. The buttons can then be used
to apply to all the selected lines at the same time.
Printing from the Project Editor
Print Setup
The Project Editor can be printed in the same way pages can. Before printing, ensure that the printer
has been set up correctly. To check the printer settings, refer to chapter 2, Pages.
Print Preview
To preview the page before printing, ensure that the Project Editor dialog is displayed and currently
selected, and then select Print Preview from the File menu.
Refer to chapter 2, Pages regarding the use of the Print Preview display.
Printing
To print the contents of the Project Editor, select the Print button from the toolbar.
Refer to chapter 2, Pages regarding the use of the Print dialog.
Release 1.2
Page 101
OMRON
CHAPTER 7 – Graphics Library
CHAPTER 7
Graphics Library
This chapter describes the CX-Supervisor Graphics Library. The chapter includes details of how the
Graphics Library may be used for storing frequently used objects for use with a number of
applications.
Overview
The Graphics Library is a repository for objects that are often used in CX-Supervisor pages. The
Graphics Library Editor allows access to Libraries from a drop-down list box. Objects are stored in
the Library and can be removed or copied, allowing quick addition of frequently used objects to
pages or which appear in a project a number of times. Libraries are not project dependant, so objects
can be copied from one project to another.
Graphics Library
Activating the Library
To activate the Library, click on the Graphics Library button on the toolbar. If the Library
is already open but displayed as an icon, double click on the Library icon.
An example of the Graphics Library Editor is illustrated as follows, but note that actual library names
and contents may differ from that shown in the following chapters.
Create Library
Each Library has a unique name which is entered when the Library is created.
To create a library, click on the Add Library button on the Graphics Library Editor toolbar.
The Add New Library dialog is displayed as illustrated below:
Release 1.2
Page 103
CHAPTER 7 – Graphics Library
OMRON
Enter the name of the new Library file and click the OK pushbutton, or cancel the addition of the
Library by clicking on the Cancel pushbutton.
If an object is dragged into the Library without a Library file open, then the Add New Library dialog
is displayed. Refer to chapter 7, Manipulating Objects, for details on dragging objects into the
Library.
Opening a Library
The Graphics Library Editor consists of a number of Libraries which are selected from the drop down
list box in the toolbar of the dialog.
Click on the Library name to display its contents in the dialog. The dialog shows the objects in the
selected Library. The content of each library is provided for reference in chapter 7, Manipulating
Objects.
Modify Library
The only element of the Library definition which is editable is the Library name. To change
the name of a Library, open the desired Library file and click on the Modify Library button
on the toolbar. The Modify Library dialog is displayed, an example of which is illustrated as
follows:
Type over the current field entry with a new name and click the OK pushbutton, or cancel the
operation by clicking the Cancel pushbutton.
Delete Library
A Library may be deleted by selecting it from the drop down list, to open it, and clicking the
Delete Library button on the Graphics Library Editor toolbar. CX-Supervisor displays a
message box to confirm the deletion of the Library.
Click the Yes pushbutton to remove the Library or the No pushbutton to cancel the operation and
return to the Graphics Library. After clicking the Yes pushbutton, a second message box is displayed
to confirm deletion of the library.
Click the OK pushbutton to delete the Library, or the Cancel pushbutton to the leave the Library
unchanged.
Page 104
Release 1.2
OMRON
CHAPTER 7 – Graphics Library
Manipulating Objects
Add Object
Any object created on a CX-Supervisor page can be added to the Library. All attributes assigned to
an object that is copied to the Library are stored, for example animation information.
To add an object, select it from a page and click the Add Object to Library button on the
Graphics Library Editor toolbar. The Add Object To Library dialog is displayed as
illustrated below:
The name of the object used by the Object Identification control is shown in the Title: field. Type
over this with a new name, if required (this is the name used by the Library). Enter a text description
in the Description: field and an identifier for the object (this is used when it is inserted on a page) in
the Identifier: field. Click the OK pushbutton to add the object to the Library and place the object in
the dialog. Click the Cancel pushbutton to abort the operation. Further details on the Object
Identification control are contained in chapter 1, Graphics Editor.
Alternatively, ensure that the Graphics Library Editor is open, click and hold the mouse button on the
page object and drag it from the page onto the Graphics Library Editor, illustrated as follows:
When the mouse button is released the object is placed in the Library, and the Add Object To Library
dialog is displayed.
Copying an object to a page from a Library is the reverse of the click and drag procedure.
Objects can also be cut or copied and pasted into the Library, refer to chapter 4, Objects. When the
object is pasted with the Graphics Library Editor open, the Add Object To Library dialog is shown.
Release 1.2
Page 105
CHAPTER 7 – Graphics Library
OMRON
Modify Library Element
To change the name of a Library object, click on the object in the Library (the object name is
highlighted in the Graphics Library Editor), and click on the Modify Library Element
toolbar button. The Modify Library Element dialog is displayed, as illustrated below:
Enter the new object title, text description and identifier. Click the OK pushbutton to add the new
object description to the Library, or the Cancel pushbutton to cancel the operation.
Delete Object
To delete an object from the Library, select the object, (the grab handles are not shown;
however, the object name is highlighted in the Graphics Library Editor) and click on the
Delete Object toolbar button.
A message box is displayed with the associated object name to remove. Click on the Yes pushbutton
to delete the object or the No pushbutton to cancel the operation.
Using a Graphic Library Object in the Graphics Editor
A library object can be added to the Graphics Editor in the same way that the Graphics Editor is used
to build libraries, by dragging from one dialog to another. Once a library object is added to the
Graphics Editor, it can be further modified since each library object is simply a group of objects.
As an example, a page can be enhanced by using one of the gauges provided in the Gauges_1 default
graphic library:
Page 106
Release 1.2
OMRON
CHAPTER 7 – Graphics Library
The gauge object can be stretched to suit the needs of the page, and other objects can be applied on
top of, or in addition to the gauge. A library object can also be ungrouped by selecting Ungroup from
the Edit menu.
The Cut, Copy and Paste buttons on the toolbar can be used as an alternative to dragging.
Default Graphic Library Objects
CX-Supervisor contains default, ready-to-use libraries. They cannot be added to (this is denoted by
the ‘READ ONLY’ statement at the bottom of the Graphics Library Editor), although they can be
applied to a page and tailored in the usual way.
Sharing Graphic Libraries
Graphic Libraries, including the default Graphic Libraries, can be shared by other users at other PCs
running CX-Supervisor. Each library has its own *.MAT file (e.g. PANELS.MAT for the panels
library). The *.MAT files reside in the same directory as the CX-Supervisor application. Using file
utilities on the PC, it is possible to copy one or more *.MAT files onto a diskette or a network, and
transfer them to a CX-Supervisor directory on another PC. Consult the Microsoft Windows User
Guide for details on copying files.
Printing the Graphics Library
Print Setup
The Graphics Library can be printed in the same way pages can. Before printing, ensure that the
printer has been set up correctly. To check the printer settings, refer to chapter 2, Pages.
Print Preview
To preview the page before printing, select Print Preview from the File menu.
Refer to chapter 2, Pages regarding the use of the Print Preview dialog.
Printing
To print the contents of the Graphics Library, select the Print button from the toolbar.
Refer to chapter 2, Pages regarding the use of the Print dialog.
Release 1.2
Page 107
CHAPTER 7 – Graphics Library
Page 108
OMRON
Release 1.2
OMRON
CHAPTER 8 – Alarms
CHAPTER 8
Alarms
This chapter describes CX-Supervisor alarms and the procedures associated with the creation,
amendment and removal of alarms using the Alarm Editing facility. The use of alarms during the
running of a project is also described.
What is an Alarm?
Alarms provide notification of a problem during the execution of an application in runtime. Alarms
are defined in the development environment and monitored in the runtime environment. Alarms
range from incidental to catastrophic in nature.
In runtime, the occurrence of an alarm condition, and any subsequent change of state, is recorded in a
log file known as the Alarm History log.
An operator is alerted to an alarm condition by means of an Alarm Acknowledge dialog, which may
also be accompanied by a warning sound. A list of current alarms is also maintained.
Individual alarms are defined in the development environment using the Alarm Editor. General
alarm settings are controlled in the development environment using the Alarm Settings dialog.
The Alarm Object (refer to chapter 4, Objects) is a graphical object which can be configured to
display alarm messages for certain groups of alarms and thus provides a convenient way of filtering
alarm messages.
Alarm definitions are made and modified using the Alarm Editor. To use the Alarm Editor, CXSupervisor must currently have a project open. If no project is currently open, either select Open
Project from the Project menu to open a previously saved project, or select New Project from the
Project menu to create a new project.
Facilities exist to add an alarm, modify an existing alarm, copy an alarm, remove an existing alarm
following confirmation, and display the alarm list in name, type or description order.
Alarm Settings
To open the Alarm Settings dialog, select the Change General Alarm Settings button from
the Alarm Editor toolbar. The dialog is displayed as follows.
Release 1.2
Page 109
CHAPTER 8 – Alarms
OMRON
In the On Alarm Automatically Display area, set the Alarm Status Viewer and Alarm History Log
settings as required. When these options are set, the Current Alarms dialog or Alarm History dialog
(respectively) displays automatically in runtime when an alarm occurs.
Set the Maximum entries in Status and Maximum entries in History Log fields to the desired values.
The numbers specify how many messages are displayed in the respective viewer dialogs in runtime.
Select the Log system start/stop messages setting to ON if required.
Note:
If more messages exist than are requested to be displayed, the most recent messages
are displayed in preference to older messages.
The Alarm Sound pushbutton allows the selection of an audible warning which are heard when an
alarm is raised. The Open Waveform File dialog is shown below:
Page 110
Release 1.2
OMRON
CHAPTER 8 – Alarms
Choosing a waveform file with this dialog does not in itself cause the warning sound to be heard
when an alarm is raised. To hear the audible warning for any alarm, the Play Sound setting in the
alarm definition must be ticked. Also, the PC on which CX-Supervisor is running must be equipped
with a suitable sound card and audio capability.
Viewing the Contents of the Alarm Database
To open the Alarm Editor dialog, click the Alarm Editor button on the toolbar. An example
of the Alarm Editor dialog is as follows:
Alarms may be segregated into groups. To select a group, pick an entry from the Group field.
All alarm definitions can be displayed by selecting <All Groups> from this list.
Individual listed alarms are sorted, based on a designated field type: name, type or description. By
selecting the Name field, the alarms are sorted alphanumerically by name. The Type and Description
fields, once selected, react in the same way. The Alarm Editor dialog shows the alarms in name
order.
The widths of the alarm fields can be widened or narrowed as required using the
mouse to drag the column boundaries.
The typeface of the editor can be amended by selecting Preferences from the File
menu. This is especially useful when printing.
The Change General Alarm Settings button on the toolbar displays the Alarm Settings
dialog, which allows global alarm settings to be modified. Refer to chapter 8, Alarm Header
Information.
Select the Large Icons button to view details with large icons.
Select the Small Icons button to view details with normal icons.
Select the List button to view details as a list.
Select the Details button to view details as a list including name, type, expression, priority
and description information. The details can be sorted in ascending order by clicking once
or in descending order by clicking twice, in the appropriate field.
Release 1.2
Page 111
CHAPTER 8 – Alarms
OMRON
A summary of alarm information is available by selecting the Display Information on
Alarms button from the toolbar. The resultant dialog shows an overall summary and a
breakdown on the number of alarms per type. To exit the dialog, click the Close pushbutton.
The Alarm Information dialog is shown as follows:
Creating a New Alarm
Open the Alarm Editor dialog, as described in chapter 8, Viewing the Contents of the Alarm
Database. To add a new alarm, select the Add Alarm button from the toolbar. This results
in the Add Alarm dialog being displayed.
Page 112
Release 1.2
OMRON
CHAPTER 8 – Alarms
Once all the information has been provided for the new alarm, selecting the OK pushbutton commits
the new alarm to the alarms database, whilst the Cancel pushbutton aborts this add operation.
Note:
The short-cut keyboard combinations for Cut, Copy and Paste operations are valid
within the Add Alarm dialog. Highlight part or all of a field and type <Ctrl>+X to
cut the text or <Ctrl>+C to copy the text. Insert the cursor at the desired field and
type <Ctrl>+V to paste the text. Since the cut and copy operations store the
information in the Windows Clipboard, it may be pasted to another dialog or
application.
Alarm Header Information
The name of the alarm is entered in the Name: field. The alarm name can be constructed of up to 20
alphanumeric characters. Any other characters, including spaces, generate an audible error, or an
Invalid Alarm Name entered message. This field is visible from the Alarm Editor dialog.
The group to which this alarm is added is selected from the Group: field. To create a new group
name, simply type the name of the new group in the Group: field. The use of alarm groups allows
filtering of alarm messages by group name.
The priority assigned to the alarm is selected from the Priority: field.
The Display Alarm Acknowledge Box setting determines whether the Acknowledge Alarm dialog is
displayed in runtime when the alarm occurs. The dialog notifies the operator of the alarm condition
and allows the operator to acknowledge the alarm. The default value is True.
Activating the Auto Acknowledge Alarm setting causes these messages to be acknowledged without
any operator action. Refer to chapter 8, Alarm Acknowledge.
The Play Sound setting determines whether an audible warning is sounded when the alarm occurs.
The default value is False. Note that a waveform file must also have been selected for the warning
sound to be heard. The waveform is selected by using the Alarm Sound pushbutton on the Alarm
Settings dialog.
An alarm description, detailing the possibilities of how the current alarm would be raised, is inserted
in the Description: field. To move to a new line, press <Ctrl>+<Return>. Any characters are valid,
and up to 255 characters may be entered in the text field. This field is visible from the Alarm Editor
dialog.
Activating the Print Alarm Messages setting causes alarms of this type to be printed automatically
when they occur.
Alarm Type
The alarm type can be Simple, Deadband or Rate of Change. Select the desired type by clicking on
the Simple, Deadband or Rate of Change settings. This field is visible from the Alarm Editor dialog.
Release 1.2
Page 113
CHAPTER 8 – Alarms
OMRON
Alarm Attributes
The attributes for an alarm are defined according to its type, as this defines when an alarm reacts.
Since Simple is the default type, the Simple alarm attributes are initially visible.
For a Simple alarm, the following attributes are displayed:
An expression based on a point is entered in the Expression: field. The alarm is raised once the point
meets the expression. The alarm is cleared when the point value subsequently fails to meet the
expression.
For a Deadband alarm, the following attributes are displayed:
An expression based on a point is entered in the Expression: field. The alarm is raised once the point
meets the expression. The alarm is cleared when the point value falls outside the expression value
plus the specified deadband percentage. For the example above an alarm is raised when the boiler’s
temperature exceeds 100 and is cleared when the boiler temperature falls below 95 (100 minus 5%).
For a Rate of Change alarm, the following attributes are displayed:
An expression based on a point is entered in the Expression: field. The alarm is raised if the value
exposed by the expression increases or decreases at the speed based on the values of the ROC: field,
the T/Base: field, and the direction based on the Direction: field. The alarm is cleared when the rateof-change is less than the critical rate.
For the above example an alarm is raised when the boiler’s temperature increases by 5% or more per
minute, and clears when the boiler’s temperature increases by less than 5% per minute.
Page 114
Release 1.2
OMRON
CHAPTER 8 – Alarms
A point may be inserted into any of the alarm types’ Expression: field by either typing in the point
name or by selecting the Browse pushbutton, which results in the Select Required Item dialog being
displayed, at the position where a point should be inserted.
Only viable points can be viewed from a Select Required Item dialog. The list of items in the Point
Names: field can be refined by selecting an option from the Group: field. Click the OK pushbutton
to accept the new point or click the Cancel pushbutton to leave the point unchanged. Clicking the
Add Point pushbutton or Add Alias pushbutton allows a new point or alias to be created prior to
association with the expression. Points are discussed in chapter 3, Points, whilst expression syntax is
discussed in the CX-Supervisor Script Language Reference Manual.
Alarm Messages
A message pertaining to a raised alarm is entered in the Raised: field. The content of the field should
be descriptive to provide the user with a reasonable basis for an alarm solution.
The Alarm Editor provides a default raised message. The name of the alarm is substituted for the #
character in the message text when the OK pushbutton is clicked. The raised message may be
changed at any time simply by entering the desired message in the text field.
A message associated with the alarm can also be entered in the Normal: field in the same manner to
that above; this message is displayed once an alarm condition has been rectified and normal
conditions have been resumed.
The Alarm Editor provides a default normal message. The name of the alarm is substituted for the #
character in the message text when the OK pushbutton is clicked. The normal message may be
changed at any time simply by entering the desired message in the text field.
Release 1.2
Page 115
CHAPTER 8 – Alarms
OMRON
Both alarm messages can include embedded point names via the Browse pushbutton, which is
replaced at runtime with the value of the point:
Example
Boiler temp high: ((BoilerTemp))
shows the point value in the alarm message.
Example
Flow exceeded, Pressure = ((Press))
((“Temperature = %2.2f”,temp)).
Updating an Existing Alarm
Open the Alarm Editor dialog as described in chapter 8, Viewing the Contents of the Alarm
Database.
To modify an existing alarm, highlight the alarm entry from the alarm list and select the
Modify Alarm button from the toolbar.
This results in the Modify Alarm dialog being displayed (a dialog based on the Add Alarm dialog), as
shown below:
Page 116
Release 1.2
OMRON
CHAPTER 8 – Alarms
The selected alarm can be redefined as described in chapter 8, Creating a New Alarm. Once all the
information has been provided for the updated alarm, clicking the OK pushbutton commits the alarm
to the alarms database, whilst the Cancel pushbutton aborts this modify operation.
Copying an Existing Alarm Definition
Open the Alarm Editor dialog as described in chapter 8, Viewing the Contents of the Alarm
Database.
To copy an existing alarm, highlight the alarm from the alarm list and then type <Ctrl>+C. This
creates a copy of the alarm definition on the Windows clipboard. To paste the alarm definition back
in to the current project, type <Ctrl>+V. The Alarm Editor ensures the name of the alarm is unique
by appending a number to the name. For example, if the original alarm name was “Alarm”, the name
of the pasted alarm is “Alarm1”. All other properties of the pasted alarm remain the same as the
original alarm definition.
It is possible to copy many alarms at once by highlighting all the desired alarms in the alarm list.
Press and hold the <Ctrl> key and use the mouse to select alarm definitions one by one, or press and
hold the <Shift> key and use the mouse to select blocks of alarm definitions. Once the desired alarms
have been highlighted, the alarm definitions may be copied and pasted in the usual way.
Alarm definitions may be pasted into a project other than the original. Care should be exercised
when attempting this procedure as the alarm expression may contain references to point names which
may have different meaning in the new project.
Deleting an Existing Alarm
Open the Alarm Editor dialog as described in chapter 8, Viewing the Contents of the Alarm
Database.
To remove an existing alarm, highlight the alarm from the alarm list and select the Delete
Alarm button from the toolbar. A confirmation dialog is displayed. Click the Yes
pushbutton to remove the alarm from the alarms database, or No pushbutton to abort the
delete operation.
Printing Alarms
Print Setup
The Alarm Editor can be printed in the same way pages can. Before printing, ensure that the printer
has been set up correctly. To check the printer settings, refer to chapter 2, Pages.
Print Preview
To preview the page before printing, select Print Preview from the File menu.
Refer to chapter 2, Pages regarding the use of the Print Preview display.
Release 1.2
Page 117
CHAPTER 8 – Alarms
OMRON
Printing
To print the contents of the Alarm Editor, click the Print pushbutton.
Refer to chapter 2, Pages regarding the use of the Print dialog.
Alarm Reporting In Runtime
An alarm condition which occurs during runtime is brought to the attention of the operator. There are
a variety of options available in the way alarms are reported. These options are configured in the
development environment. During runtime, there are essentially four ways of examining alarm
messages: the Alarm Acknowledge dialog, the Current Alarm dialog, the Alarm History dialog and
the Alarm Object.
The Alarm Object is a graphical object which displays alarm messages in a similar way to the alarm
status viewer. Refer to chapter 4, Objects for an explanation of how to configure an alarm object to
filter alarm messages by group name.
Alarm Acknowledge
Whenever an alarm is raised during a runtime application, a confirmation dialog is optionally
displayed requesting acknowledgement of the alarm. The dialog shows the alarm message, priority,
and the date and time the alarm was raised. Click the Acknowledge pushbutton to close the dialog.
Alarm messages are queued so that as each message is acknowledged, the next in the queue becomes
visible. If a new alarm occurs which has higher or equal priority the details are updated to show this
newer/more important alarm first. The dialog disappears when there are no further alarm messages to
be reported. Each acknowledgement is logged in the alarm history log with the login name of the
current user. An unacknowledged alarm does not affect a runtime application.
Page 118
Release 1.2
OMRON
CHAPTER 8 – Alarms
Current Alarms
A list of current alarms can be viewed by accessing the Current Alarms dialog. (A “current” alarm is
one which has been raised but is not yet cleared and acknowledged.) The current alarm status viewer
can be accessed in a variety of ways, and is dependant on the setup of the runtime application. Some
applications may allow access to the dialog via the context-sensitive floating menu, whilst others may
allow access via a pushbutton. Refer to chapter 6, Projects or chapter 9, Animation as appropriate.
The Current Alarms dialog is as follows:
The Current Alarm dialog always shows the alarm messages listed in order with the highest priority
at the top.
The widths of the alarm fields can be widened or narrowed as required using the
mouse to drag the column boundaries.
The Acknowledge Selected Alarm toolbar button acknowledges the alarm which is
currently highlighted in the alarm status dialog. This has no effect if the alarm has already
been acknowledged.
The Acknowledge All Outstanding Alarms toolbar button unconditionally acknowledges
all outstanding alarms. Any unacknowledged alarms become acknowledged. This has no
effect on alarms that are already acknowledged.
The Print Contents of Alarm Status View toolbar button causes the messages in the alarm
status dialog to be printed. Before printing, ensure that the printer has been set up correctly.
Alarm History
The occurrence of an alarm condition, and any subsequent change of state, is recorded in the alarm
history log. Alarm messages recorded in the log can be displayed using the Alarm History dialog.
The Alarm History dialog can be accessed in a variety of ways, and is dependant on the setup of the
runtime application. Some applications may allow access to the dialog via the context-sensitive
floating menu, whilst others may allow access via a pushbutton. Refer to chapter 6, Projects or
chapter 9, Animation as appropriate. The Alarm History dialog is as follows:
Release 1.2
Page 119
CHAPTER 8 – Alarms
OMRON
This dialog always shows the log listed in date and time order.
The widths of the alarm fields can be widened or narrowed as required using the
mouse to drag the column boundaries.
The Print Contents of Alarm Log View toolbar button causes the messages in the Alarm
History dialog to be printed. Before printing, ensure that the printer has been set up
correctly. The alarm log itself is simply a text file (projectname.alg) that may be examined
or printed using any of the usual utilities available under Windows, such as Microsoft
Notepad.
Page 120
Release 1.2
OMRON
CHAPTER 9 – Animation
CHAPTER 9
Animation
This chapter describes CX-Supervisor animation and the procedures associated with the creation of a
project animation, page animation and object animation, using the Animation Editing facility. The
active use of points and how points dictate animations is also described.
Associating Points with Actions and Events
CX-Supervisor provides a facility to greatly enhance the versatility of a runtime application by the
use of actions and animations to execute commands and logical expressions based on specified
criteria being met. This can take many forms, for instance pressing a button, opening or closing a
page or changes in the positioning of objects on a page.
CX-Supervisor achieves this enhanced functionality in two ways: by assigning an expression to a predefined action, or executing commands on a linear basis as a basic programming language. In
addition, such functionality can be carried out on three levels: object, page, or project, with different
objectives at each level.
Animations are actioned using the values or states of one or more points. For example, an integer
point is assigned to an object, the colour of the object is black when the value of the point is “0”. The
system causes the value of the point to be changed to the value “5”, which changes the colour of the
object to red.
To demonstrate, an object’s colour can be changed in the runtime environment from black to white.
This can be achieved using actions and animations in the two ways described, with the additional use
of points. Firstly, using a pre-defined action, the object can be associated with the ‘Change Colour’
pre-defined action (runtime action). When a Boolean point’s value is “0” the colour is black, when
the point’s value is “1” the colour is white. The same result can be achieved using the basic
programming language (script). This time, a single command can change the colour from black to
white. Finally, either instance can be initiated by the user in the runtime environment, e.g. the user
presses a pushbutton to change the object’s colour.
This is a simple example, but underlines how quickly and smoothly a runtime application can be
built. This chapter elaborates on all forms of actions and animations that can be applied to CXSupervisor in the development environment. Also refer to the CX-Supervisor Script Language
Reference Manual for further syntax details for the application of actions and animations.
Animation Editor
Actions and animations are created on a project, page or object basis using the Animation Editor.
To use the Animation Editor, CX-Supervisor must currently have a project open. If no project is
currently open, select Open from the Project menu to open a previously saved project, or select New
from the Project menu to create a new project.
Release 1.2
Page 121
CHAPTER 9 – Animation
OMRON
To access the Animation Editor, select the Animation Editor pushbutton from the toolbar.
The Animation Editor dialog is displayed:
The Animation Editor dialog lists all possible animation actions in the Runtime Actions column.
Attributable objects for the Runtime Actions are listed in the Trigger Event/Expression column.
Animations can be instigated on a Project, Page or Object basis by selecting Object Actions, Page
Actions or Project Actions from the Actions field. When opening the Animation Editor whilst an
object within a page is selected, the Actions field defaults to Object Actions, and the selected object is
shown in the Animation Editor. When accessing the Animation Editor with a page selected, this field
defaults to Page Actions. When opening the Animation Editor whilst no selection is made, the
Actions field defaults to Project Actions. The actions that may be applied to an object are dependant
on the type of object selected. Only one type of action, Execute Script, can be applied to a Page or
Project script.
The Users field allows selection of which users can use the selected page in the Runtime
environment. This is used in conjunction with allocating users and allowing them permission to
perform tasks; for further information on allocating users refer to chapter 6, Projects.
If Object Actions is the current selection for the Actions field, an object becomes active in the Object
(left-most) field. An object within the current page can be selected from the Object field. The
Runtime Actions list is dependant on the object selected from this box. The Object field is disabled
for Page or Project actions.
Page 122
Release 1.2
OMRON
CHAPTER 9 – Animation
Individual listed Runtime Actions are sorted, based on a designated field type, either Runtime
Actions or Trigger Event/Expression. By clicking on the Runtime Actions pushbutton, the points
are sorted alphanumerically by Runtime Actions. The Trigger Event/Expression pushbutton, once
selected, reacts in the same way. The Animation Editor dialog shows the actions associated with
‘Polygon_1’ sorted in runtime action order.
The typeface of the editor can be amended by selecting Preferences from the File menu. This is
especially useful when printing.
The widths of the animation fields can be widened or narrowed as required using the
mouse to drag the column boundaries.
A new action can be added to the list of current actions by clicking the Add Action
button in the toolbar. An existing action can be removed from the current actions by
clicking the Delete Action button in the toolbar, whereupon a confirmation dialog is
displayed. Click the OK pushbutton to delete the action, or click the Cancel
pushbutton to abort the delete operation. An existing action can be modified from
the current actions by clicking the Modify Action button in the toolbar.
Note:
The short-cut keyboard combinations for Cut, Copy and Paste operations are valid
within the Animation Editor dialogs. Highlight part or all of a field and type <Ctrl>+X
to cut the text or <Ctrl>+C to copy the text; insert the cursor at the desired dialog field
and type <Ctrl>+V to paste the text. Since the cut and copy operations store the
information in the Windows Clipboard, it may be pasted to another dialog or
application.
View Mode
The list of runtime actions can be viewed in a number of ways, providing simple or comprehensive
details as follows:
Select the Large Icons button to view details with large icons.
Select the Small Icons button to view details with normal icons.
Select the List button to view details as a list.
Select the Details button to view details as a list including runtime actions, trigger/event
expression and access. The details can be sorted in ascending order by clicking once or in
descending order by clicking twice, in the appropriate field.
Project
Graphical objects have no relevance at Project level as they cannot be referenced. Scripts can be
applied to a project to manipulate points. These scripts are associated with events that occur
throughout the operating session. A script is made up of one or more simple statements that together
make script code.
Release 1.2
Page 123
CHAPTER 9 – Animation
OMRON
Refer to the Script Language Manual for explicit details regarding the construction and syntax of
script code. Chapter 10, Runtime Actions describes the creation of script code using the Script
Editor.
The script is defined using the Execute Script entry in the Animation Editor list.
Page
Page scripts are concerned with manipulating points and graphical objects that are used or included
within that page. Actions cannot refer to graphical objects that appear in other pages. In other words,
page scripts are used to drive a number of actions on the occurrence of a particular event. An
example of page script code is as follows:
REM ** move the car and transport **
IF start THEN
Position = position – speed
ENFIF
REM ** if the car is at the start then reset the **
REM ** position and reset the car colour **
IF position < 0THEN
position = 800
POLYGON_11.colour = dark_grey
ENDIF
REM setup the paint spray colour **
IF position < 300 || position > 400 && changepaint THEN
IF paintblue THEN
POLYGON_34.colour = dark_blue
ENDIF
IF paint green THEN
POLYGON_34.colour = Dark_green
ENDIF
IF paintred THEN
POLYGON_34.colour = red
ENDIF
IF paintpurple THEN
POLYGON_34.colour = purple
ENDIF
IF paintyellow THEN
POLYGON_34.colour = yellow
ENDIF
IF paintwhite THEN
POLYGON_34.colour = white
ENDIF
Page 124
Release 1.2
OMRON
CHAPTER 9 – Animation
ENDIF
Refer to the Script Language Manual for explicit details regarding the construction and syntax of
script code. 10.3 Runtime Actions describes the creation of script code using the Script Editor.
The script is defined using the Execute Script entry in the Animation Editor list.
Objects
One object or a selection of objects defined as a group are animated in a number of ways (refer to
chapter 1, Graphics Editor for applicable objects):
♦
An object can be seen to be blinking.
♦
An object can be removed from the page.
♦
An object can change colour.
♦
A value associated with the object can be displayed.
♦
Text associated with the object can be displayed.
♦
An object can appear enabled for selection or disabled for selection.
♦
An object can move horizontally or vertically.
♦
An object can be flood-filled.
♦
An object can change its size, horizontally or vertically.
♦
An object can rotate.
♦
An object can have associated user interaction.
♦ An object can be displayed on the page.
However, it is not feasible for all the objects to be capable of all forms of animation. For instance, a
toggle object can only be animated so that it is enabled or disabled, visible or invisible, whilst a text
object can be resized, moved, change its colour, blink, rotate, await user interaction, be made visible
or invisible, or display an associated value. A list of objects and their available animations is as
follows:
Release 1.2
Page 125
CHAPTER 9 – Animation
OMRON
Blink
9 9 9 9 9 9 9 9 9
Close page
9 9 9 9 9 9 9 9 9 9
Colour Change (Analogue)
9 9 9 9 9 9 9 9 9 9 9
9
9 9 9 9
Colour Change (Digital)
9 9 9 9 9 9 9 9 9 9 9
9
9 9 9 9
Display page
9 9 9 9 9 9 9 9 9 9
Display Value (Analog)
9
Display Value (Digital)
9
Display Value (Text)
9
Edit point value (Analogue)
9 9 9 9 9 9 9 9 9 9
9 9
9
Edit point value (Digital)
9 9 9 9 9 9 9 9 9 9
9 9
9
Edit point value (Text)
9 9 9 9 9 9 9 9 9 9
9 9
9
Enable/Disable
9 9 9 9 9 9 9 9 9 9 9 9
9 9
Execute script
9 9 9 9 9 9 9 9 9 9
9 9
Move (Horizontal)
9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9
Move (Vertical)
9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9
Percentage fill (Horizontal)
9 9 9
9
9 9
9 9
9 9
Resize (Height)
9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9
Resize (Width)
9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9
Rotate
Percentage fill (Vertical)
Visibility
9 9
9 9 9
9 9
9
9 9
9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9
A group object possesses the animation functions common to all objects within the group.
The ticks denote whether the animation function is available for the object. The blank cells denote
the animation function is not available for the object. The icons within the table header denote the
object created by that icon. Refer to chapter 1, Graphics Editor for further details.
In addition, an object can be animated in the form of a script. A script is made up of one or more
statements. An example of object script code is as follows:
REM ** SET UP THE COLOUR FLAGS **
Page 126
Release 1.2
OMRON
CHAPTER 9 – Animation
Paintblue = TRUE
paintgreen = FALSE
paintred = FALSE
paintpurple = FALSE
paintyellow = FALSE
paintwhite = FALSE
REM ** SET UP THE VALVE POSITION **
Bluevalve = TRUE
greenvalve = FALSE
redvalve = FALSE
Changepaint = TRUE
Refer to the Script Language Manual for full details regarding the construction and syntax of script
code. The script is created by selecting the Execute Script entry in the Animation Editor list.
Chapter 10, Runtime Actions describes the application of object animations.
Printing the Animation Editor
Print Setup
The Animation Editor can be printed in the same way pages can. Before printing, ensure that the
printer has been set up correctly. To check the printer settings, refer to chapter 2, Pages.
Print Preview
To preview the page before printing, select Print Preview from the File menu.
Refer to chapter 2, Pages regarding the use of the Print Preview display.
Printing
To print the contents of the Animation Editor, select the Print button from the toolbar.
Refer to chapter 2, Pages regarding the use of the Print dialog.
Runtime Actions
Script
A script, controlling the actions of an object, page or project can be created and updated using the
Script Editor dialog.
Release 1.2
Page 127
CHAPTER 9 – Animation
OMRON
The Script Editor allows script code to be created or amended which carries out the mechanics of the
animation operation. To access the Script Editor dialog to add an action, select Execute Script from
the animation list and click on the Add Action button on the toolbar. To access the Script Editor to
modify an action, select Execute Script from the animation list and click on the Modify Action
button on the toolbar. Refer to the Script Reference chapter 10, Objects, for a list of the objects to
which an Execute Script action is applicable. Page Animations and Project Animations may have an
Execute Script action.
On selection of the Execute Script action, the Script Editor dialog is displayed:
When creating the script choosing an action, function, etc. from the menu may require further
information. This subsequent information is provided using some common dialogs: the Select
Required Item dialog, the Simple Expression Entry dialog and the Object Selection dialog.
Use the Select Required Item dialog to ‘pick’ a point to associate with the current action. It is
accessed by clicking the Browse pushbutton from the current dialog. This results in the Select
Required Item dialog being displayed.
Page 128
Release 1.2
OMRON
CHAPTER 9 – Animation
Only relevant points are listed in the Point Names: field. Select the desired point from the Point
Names: list, and click the OK pushbutton. Clicking the Cancel pushbutton aborts the selection. To
add a new point click the Add Point pushbutton; for details on adding a point refer to chapter 3,
Points.
Use the Simple Expression Entry dialog to assign an expression to an action. It is accessed from an
entry in the script code. This results in the Simple Expression Entry dialog being displayed:
Enter the expression in the Expression: field. The Browse pushbutton can be used to pick a valid
point. Click the OK pushbutton to proceed, or the Cancel pushbutton to abort.
Use the Select Required Object dialog to assign an object to an action. It is accessed from an entry in
the script code. This results in the Select Required Object dialog being displayed:
Release 1.2
Page 129
CHAPTER 9 – Animation
OMRON
Select an object from the Object Names: field. Click the OK pushbutton to proceed, or the Cancel
pushbutton to abort.
Note:
The short-cut keyboard combinations for Cut, Copy and Paste operations are valid
within the Script Editor. Highlight part or all of a field and type <Ctrl>+X to cut
the text or <Ctrl>+C to copy the text; insert the cursor at the desired field and type
<Ctrl>+V to paste the text. Since the cut and copy operations store the information
in the Windows Clipboard, it may be pasted to another dialog or application.
Aliases
An alias definition can be provided to replace strings in scripts and expressions used throughout CXSupervisor applications. An associated string replaces the alias when used in a script or expression.
Select the Aliases pushbutton from the Script Editor dialog. The Alias Definitions dialog is
displayed. Refer to chapter 6, Projects for more details on alias definitions.
Execution Attributes
The animation reacts to an event. A script can be associated with an event, depending on whether it
is a project script, page script or object script.
For a project or page script, the following events trigger the execution of the script:
♦
On a condition, based on a regular expression.
♦
At a regular interval defined by an interval time.
♦
At the initialisation of the page or project.
♦ At the termination of the page or project.
For an object script, the following events trigger the script:
♦
Following the user clicking once on the left mouse button.
♦
On a condition, based on a regular expression.
Page 130
Release 1.2
OMRON
CHAPTER 9 – Animation
To specify a trigger for the script, select an option from the Trigger Event: field.
Note:
If On condition is specified, a valid relational expression is required in the
Expression: field. The script is executed every time a variable included in the
expression changes value and the result of the expression is ‘TRUE’. For example,
the expression $Second executes every second except when $Second is zero;
whereas $Second >= 0 executes every second. If an invalid expression is entered,
an error message is displayed when the OK pushbutton is clicked.
Note:
If On Regular Interval is specified, a valid interval is required in the Interval Time:
field in units of milliseconds. The script is started at the interval specified by this
period. If an invalid time is entered, an error message is displayed when the OK
pushbutton is clicked.
Script Code
Script code is entered in the script code text field. To start a new line, press <Return>.
Refer to the Script Language Manual for explicit details regarding the construction and syntax of
script code.
Expressions consist of operators and operands:
♦
Operators are relational, arithmetic, logical and include many functions.
♦ Operands are constants or point variables.
The script language can also contain Java and Visual Basic script. Refer to the Script Language
Manual for details.
Scripts can be generated either by typing directly into the script code text field or by using the pull
down menu commands. When using the pull down menu commands the user is assisted in the
completion of the parameters to the command via a series of dialogs. The dialogs displayed vary
according to the type of command being entered.
Release 1.2
Page 131
CHAPTER 9 – Animation
OMRON
Points
A point may be inserted into the script code in a number of ways:
♦
Clicking the Browse pushbutton, picking the point off the list and clicking the OK pushbutton.
♦ Typing the name of the point
System points form part of the points list.
Undo Last Action
The last edit performed can be undone, if required, in a number of ways:
♦
Selecting Undo from the Edit menu.
♦
Pressing <Ctrl>+Z in the script code text field.
Cut to Clipboard
An area of script code can be moved to the Microsoft Windows Clipboard in a number of ways:
♦
Selecting the script code to cut, followed by Cut from the Edit menu.
♦
Selecting the script code to cut in the script code text field and pressing <Ctrl>+X.
Copy to Clipboard
An area of script code can be copied to the Clipboard, if required, in a number of ways:
♦
Selecting the script code to copy, followed by Copy from the Edit menu.
♦
Selecting the script code to copy from the script code text field and pressing <Ctrl>+C.
Paste from Clipboard
An area of script code can be copied from the Clipboard, if required, in a number of ways:
♦
Placing the I-beam cursor at the desired point in the script code field, followed by Paste from the
Edit menu.
♦
Placing the I-beam cursor at the desired point in the script code field and then pressing
<Ctrl>+V.
Insert Tab Code
A tab character can be inserted into the script code, if required, in a number of ways:
♦
Placing the I-beam cursor at the desired point in the script code field, followed by Tab from the
Edit menu.
♦
Placing the I-beam cursor at the desired point in the script code field and then pressing
<Ctrl>+<Tab>.
Page 132
Release 1.2
OMRON
CHAPTER 9 – Animation
Finding and Replacing Text
Text can be found and replaced within the current script as follows:
♦
Select Find/Replace from the Edit menu and type appropriate text in the Find what and Replace
with fields. Press the Find pushbutton to initiate the search and <Return> to execute text
replacement.
Clear Script Code Field
The script code field can be cleared, if required:
♦
Selecting Clear All from the Edit menu.
Script Completion
Once script entry or script modification is complete, click the OK pushbutton. To abort the Script
Editor prior to completing the task, click the Cancel pushbutton.
If there is an error in the script, the Compilation Error(s) dialog is displayed.
In this example, the error is caused by a spurious ‘ENDIF’.
This dialog informs the user where an error has occurred and its type. If necessary, use the scroll bars
to see the whole error message. Click the OK pushbutton to remove the Compilation Error(s) dialog
and return to the Script Editor to fix the error.
Horizontal Move
Objects can be animated by moving either left or right. This is specified using the Move (Horizontal)
dialog.
Release 1.2
Page 133
CHAPTER 9 – Animation
OMRON
To access the Move (Horizontal) dialog to add an action, select Move (Horizontal) from the
animation list and click the Add Action button on the toolbar. To access the Move (Horizontal)
dialog to modify an action, select Move (Horizontal) from the animation list and click the Modify
Action button on the toolbar. Refer to the Script Reference chapter 10, Objects, for a list of the
objects to which this action is applicable.
On selection of the Move (Horizontal) action, the Move (Horizontal) dialog is displayed:
To define the animation, an expression consisting of a number of operators and operands (which may
be based on the status of a point) must be entered in the Expression: field. The boundaries in which
the object moves are inserted into the Active Expression Range/Required Position: fields. The
Maximum Offset specifies the number of pixels to the right (from its initial position) that the object
moves when the result of the expression reaches the Maximum Value. The Minimum Offset specifies
the number of pixels to the left (from its initial position) that the object moves, when the result of the
expression reaches the Minimum Value. A value within the maximum and minimum values results in
a proportionate movement between the left and right positions.
To abort the Horizontal Move definition, click the Cancel pushbutton. By clicking the Browse
pushbutton, a point may be directly specified, as described in chapter 9, Runtime Actions. Once
completed, click the OK pushbutton. If invalid data has been inserted into any field, a descriptive
error message is displayed.
Vertical Move
Objects can be animated by moving either up or down. This can be specified via the Move (Vertical)
dialog.
To access the Move (Vertical) dialog to add an action, select Move (Vertical) from the animation list
and click the Add Action button on the toolbar. To access the Move (Vertical) dialog to modify an
action, select Move (Vertical) from the animation list and click the Modify Action button on the
toolbar. Refer to chapter 9, Objects, for a list of the objects to which this action is applicable.
On selection of the Move (Vertical) action, the Move (Vertical) dialog is displayed:
Page 134
Release 1.2
OMRON
CHAPTER 9 – Animation
To define the animation, an expression based on the status of a point must be entered in the
Expression: field. The boundaries in which the object moves are inserted into the Active Expression
Range/Required Position: fields. The Maximum Offset specifies the number of pixels upwards (from
its initial position) that the object moves, when the result of the expression reaches the Maximum
Value. The Minimum Offset specifies the number of pixels downwards (from its initial position) that
the object moves, when the result of the expression reaches the Minimum Value. A value within the
maximum and minimum values results in a proportionate movement between the top and bottom
positions.
To abort the Vertical Move definition, click the Cancel pushbutton. By clicking the Browse
pushbutton, a point may be directly specified, as described in chapter 9, Runtime Actions. Once
completed, click the OK pushbutton. If invalid data has been inserted into any field, a descriptive
error message is displayed.
Resize Width
Objects can be animated by shrinking or expanding horizontally. This can be specified via the Resize
(Width) dialog.
To access the Resize (Width) dialog to add an action, select Resize (Width) from the animation list
and click the Add Action button on the toolbar. To access the Resize (Width) dialog to modify an
action, select Resize (Width) from the animation list and click the Modify Action button on the
toolbar. Refer to chapter 9, Object, for a list of the objects to which this action is applicable.
On selection of the Resize (Width) action, the Resize (Width) dialog is displayed:
Release 1.2
Page 135
CHAPTER 9 – Animation
OMRON
To define the animation, an expression consisting of a number of operators and operands (which may
be based on the status of a point) must be entered in the Expression: field.
The boundaries in which the object moves are inserted into the Active Expression Range/Required
Width: fields. The Maximum Width specifies the required width in pixels of the object when the
result of the expression reaches the Maximum Value. The Minimum Width specifies the required
width in pixels of the object when the result of the expression reaches the Minimum Value. A value
within the maximum and minimum values results in a proportionate width between the minimum and
maximum widths. The resizing also requires an anchor and direction in which to stretch or shrink.
This can be specified as the left of the object, right of the object or centrally to the object, by
selecting the appropriate Justification: setting.
To abort the Resize Width definition, click the Cancel pushbutton. By clicking the Browse
pushbutton, a point may be directly specified, as described in chapter 9, Runtime Actions. Once
completed, click the OK pushbutton. If invalid data has been inserted into any field, a descriptive
error message is displayed.
Resize Height
Objects can be animated by shrinking or expanding vertically. This can be specified via the Resize
(Height) dialog.
To access the Resize (Height) dialog to add an action, select Resize (Height) from the animation list
and click the Add Action button on the toolbar. To access the Resize (Height) dialog to modify an
action, select Resize (Height) from the animation list and click the Modify Action button on the
toolbar. Refer to chapter 9, Objects, for a list of the objects to which this action is applicable.
On selection of the Resize (Height) action, the Resize (Height) dialog is displayed:
To define the animation, an expression consisting of a number of operators and operands (which may
be based on the status of a point) must be entered in the Expression: field.
The boundaries in which the object moves are inserted into the Active Expression Range/Required
Height: fields. The Maximum Height specifies the required height in pixels of the object when the
result of the expression reaches the Maximum Value. The Minimum Height specifies the required
height in pixels of the object when the result of the expression reaches the Minimum Value. A value
Page 136
Release 1.2
OMRON
CHAPTER 9 – Animation
within the maximum and minimum values results in a proportionate height between the minimum
and maximum heights The resizing also requires an anchor and direction in which to stretch or
shrink. This can be specified as the top of the object, bottom of the object or centrally to the object,
by selecting the appropriate Justification: setting.
To abort the Resize Height definition, click the Cancel pushbutton. By clicking the Browse
pushbutton, a point may be directly specified, as described in chapter 9, Runtime Actions. Once
completed, click the OK pushbutton. If invalid data has been inserted into any field, a descriptive
error message is displayed.
Horizontal Percentage Fill
Closed objects can be flood-filled along a horizontal axis. This can be specified via the Percentage
Fill (Horizontal) dialog.
To access the Percentage Fill (Horizontal) dialog to add an action, select Percentage Fill (Horizontal)
from the animation list and click the Add Action button on the toolbar. To access the Percentage Fill
(Horizontal) dialog to modify an action, select Percentage Fill (Horizontal) from the animation list
and click the Modify Action button on the toolbar. Refer to chapter 9, Objects, for a list of the
objects to which this action is applicable.
On selection of the Percentage Fill (Horizontal) action, the Percentage Fill (Horizontal) dialog is
displayed:
To define the animation, an expression consisting of a number of operators and operands (which may
be based on the status of a point) must be entered in the Expression: field.
The boundaries associated with the percentage fill are inserted into the Active Expression
Range/Required Percentage Fill: fields. The % Filled fields specify the percentage of the object to
fill when the expression reaches its maximum and minimum values. The flood-fill also requires a
direction. This can be specified as left to right or right to left, by selecting the appropriate Fill
Direction: setting.
Release 1.2
Page 137
CHAPTER 9 – Animation
OMRON
To abort the Horizontal Percentage Fill definition, click the Cancel pushbutton. By clicking the
Browse pushbutton, a point may be directly specified, as described in chapter 9, Runtime Actions.
Once completed, click the OK pushbutton. If invalid data has been inserted into any field, a
descriptive error message is displayed.
Vertical Percentage Fill
Closed objects can be flood-filled along a vertical axis. This can be specified via the Percentage Fill
(Vertical) dialog.
To access the Percentage Fill (Vertical) dialog to add an action, select Percentage Fill (Vertical) from
the animation list and click the Add Action button on the toolbar. To access the Percentage Fill
(Vertical) dialog to modify an action, select Percentage Fill (Vertical) from the animation list and
click the Modify Action button on the toolbar. Refer to chapter 9, Objects, for a list of the objects to
which this action is applicable.
On selection of the Percentage Fill (Vertical) action, the Percentage Fill (Vertical) dialog is
displayed:
To define the animation, an expression consisting of a number of operators and operands, which may
be based on the status of a point, must be entered in the Expression: field.
The boundaries in which the object moves are inserted into the Active Expression Range/Required
Percentage Fill: fields. The % Filled fields specify the percentage of the object to fill when the
expression reaches its maximum and minimum values. The flood-fill also requires a direction. This
can be specified as top to bottom or bottom to top, by selecting the appropriate Fill Direction: setting.
To abort the Vertical Percentage Fill definition, click the Cancel pushbutton. By clicking the
Browse pushbutton, a point may be directly specified, as described in chapter 9, Runtime Actions.
Once completed, click the OK pushbutton. If invalid data has been inserted into any field, a
descriptive error message is displayed.
Page 138
Release 1.2
OMRON
CHAPTER 9 – Animation
Display Page
CX-Supervisor allows the specification of pages within a project for display. This is set up using the
Display Page dialog.
To access the Display Page dialog to add an action, select Display Page from the animation list and
click the Add Action button on the toolbar. To access the Display Page dialog to modify an action,
select Display Page from the animation list and click the Modify Action button on the toolbar. Refer
to chapter 9, Objects, for a list of the objects to which this action is applicable.
On selection of the Display Page action, the Display Page dialog is displayed:
To specify a page for display, select a page from the Available Pages: list and click on the Add
pushbutton. The page entry now appears in the Pages to be Displayed: list. More than one page can
be selected for display. If a selected page is no longer required, select the entry from the Pages to be
Displayed: list, and click on the Remove pushbutton.
Once completed, click the OK pushbutton.
pushbutton.
To abort the Display Page edit, click the Cancel
Close Page
CX-Supervisor allows the specification of pages within a project to be removed from the display.
This is set up using the Close Page dialog.
To access the Close Page dialog, select Close Page from the animation list and click the Add Action
button on the toolbar. To access the Close Page dialog to modify an action, select Close Page from
the animation list and click the Modify Action button on the toolbar. Refer to chapter 9, Objects, for
a list of the objects to which this action is applicable.
Release 1.2
Page 139
CHAPTER 9 – Animation
OMRON
On selection of the Close Page action, the Close Page dialog is displayed:
To specify a page for removal, select a page from the Available Pages: list and click on the Add
pushbutton. The page now appears in the Pages to be Closed: list. Multiple pages can be selected
for removal. If a selected page for removal is no longer required for that purpose, select the page
from the Pages to be Closed: list, and click on the Remove pushbutton.
Once completed, click the OK pushbutton.
pushbutton.
To abort the Close Page edit, click the Cancel
Blink
Objects can be animated so that they blink. This is achieved using the Blink dialog.
To access the Blink dialog to add an action, select Blink from the animation list and click the Add
Action button on the toolbar. To access Blink dialog to modify an action, select Blink from the
animation list and click the Modify Action button on the toolbar. Refer to chapter 9, Objects, for a
list of the objects to which this action is applicable.
On selection of the Blink action, the Blink dialog is displayed:
Page 140
Release 1.2
OMRON
CHAPTER 9 – Animation
Enter a Boolean expression in the Digital Expression: field. Arithmetic, logical and relational
expressions may also be entered as long as the result of the expression is zero or non-zero, i.e. the
result equates to ‘TRUE’ or ‘FALSE’. When the result of the expression is ‘TRUE’ the object(s)
blinks.
To select a colour for the blink animation, click in the Blink Colour: field. The Colour Palette dialog
is displayed so that a colour can be supplied to the object. The object blinks between its current
colour and the chosen blink colour. The Colour Palette dialog is described in chapter 9, Common
Colour Palette.
Once completed, click the OK pushbutton. To abort the Blink operation, click the Cancel
pushbutton. By clicking the Browse pushbutton, a point may be directly specified, as described in
chapter 9, Runtime Actions.
Colour Change (Analogue)
Objects can be animated so they change between a variety of colours at a variety of intervals. This is
achieved using the Colour Change (Analogue) dialog.
To access the Colour Change (Analogue) dialog to add an action, select Colour Change (Analogue)
from the animation list and click the Add Action button on the toolbar. To access the Colour Change
(Analogue) dialog to modify an action, select Colour Change (Analogue) from the animation list and
click the Modify Action button on the toolbar. Refer to chapter 9, Objects, for a list of the objects to
which this action is applicable.
On selection of the Colour Change (Analogue) action, the Colour Change (Analogue) dialog is
displayed:
Enter an expression in the Analogue Expression: field which results in a real or integer value. Only
when the result of the expression reaches a value identified as a threshold does the object change
colour.
Release 1.2
Page 141
CHAPTER 9 – Animation
OMRON
The object can have one of five colours depending on the value of the expression. It changes
between these colours at the thresholds. For example, choose the colour blue for the first colour, and
the value 20 for the first threshold. The object then changes to blue until the value reaches 20, at
which point it changes to the second colour. To apply the change to the frame of the object, select
the Apply colour changes to object frame setting. To apply the change to the object background,
select the Apply colour changes to object background setting.
On selection of a colour in the Colour Change (Analogue) dialog, the Colour Palette dialog is
displayed. The Colour Palette dialog is described in chapter 9, Common Colour Palette.
Click the Clear pushbutton to reset all colours and re-start. To abort the Colour Change (Analogue)
edit, click the Cancel pushbutton. By clicking the Browse pushbutton, a point may be directly
specified, as described in chapter 9, Runtime Actions. Once completed, click the OK pushbutton. If
invalid data has been inserted into any field, a descriptive error message is displayed.
Colour Change (Digital)
Objects can be animated so they change between two colours. This is achieved using the Colour
Change (Digital) dialog.
To access the Colour Change (Digital) dialog to add an action, select Colour Change (Digital) from
the animation list and click the Add Action button on the toolbar. To access Colour Change (Digital)
dialog to modify an action, select Colour Change (Digital) from the animation list and click the
Modify Action button on the toolbar. For a list of the objects to which this action is applicable refer
to chapter 9, Objects.
On selection of the Colour Change (Digital) action, the Colour Change (Digital) dialog is displayed:
To specify a change in an object’s colour, enter a Boolean expression in the Digital Expression: field.
Non-Boolean expressions may be entered as long as the result is ‘TRUE’ or ‘FALSE’.
The colours are specified in the Colour Attributes: fields for Boolean State 0 and Boolean State 1. To
apply the change to the frame of the object, select the Apply colour changes to object frame setting.
To apply the change to the object background, select the Apply colour changes to object background
setting.
Page 142
Release 1.2
OMRON
CHAPTER 9 – Animation
On selection of a colour in the Colour Change (Digital) dialog, the Colour Palette dialog is displayed.
The Colour Palette dialog is described in chapter 9, Common Colour Palette.
To abort the Colour Change (Digital) edit, click the Cancel pushbutton. By clicking the Browse
pushbutton, a point may be directly specified, as described in chapter 9, Runtime Actions. Once
completed, click the OK pushbutton. If invalid data has been inserted into any field, a descriptive
error message is displayed.
Enable/Disable
Objects can be enabled or disabled. This is achieved using the Enable/Disable dialog.
To access the Enable/Disable dialog to add an action, select Enable/Disable from the animation list
and click the Add Action button on the toolbar. To access the Enable/Disable dialog to modify an
action, select Enable/Disable from the animation list and click the Modify Action button on the
toolbar. For a list of the objects to which this action is applicable refer to chapter 9, Objects.
On selection of the Enable/Disable action, the Enable/Disable dialog is displayed:
To specify a change in the enabled/disabled state of an object, enter a Boolean expression in the
Digital Expression: field. Non-Boolean expressions may be entered as long as the result is ‘TRUE’
or ‘FALSE’. Whether the object is enabled or disabled when the expression is ‘TRUE’ is chosen
with the Enable/Disable State settings.
Once completed, click the OK pushbutton. To abort the Enable/Disable operation, click the Cancel
pushbutton. If invalid data has been inserted into any field, a descriptive error message is displayed.
By clicking the Browse pushbutton, a point may be directly specified, as described in chapter 9,
Runtime Actions.
Rotate
An object can be rotated about its centre. Specify this using the Rotate dialog.
To access the Rotate dialog to add an action, select Rotate from the animation list and click the Add
Action button on the toolbar. To access the Rotate dialog to modify an action, select Rotate from the
animation list and click the Modify Action button on the toolbar. For a list of the objects to which
this action is applicable refer to chapter 9, Objects.
Release 1.2
Page 143
CHAPTER 9 – Animation
OMRON
On selection of the Rotate action, the Rotate dialog is displayed:
Enter an arithmetic expression in the Expression: field. The constraints of the rotation animation are
specified in the Active Expression Range/Required Rotation: fields. Rotation is clockwise and the
angle is specified in degrees..
Enabling the Fix point on screen option ensures that the rotation point remains at the same location
even if the object moves.
To abort the Rotate edit, click the Cancel pushbutton. By clicking the Browse pushbutton, a point
may be directly specified, as described in chapter 9, Runtime Actions. completed, click the OK
pushbutton. If invalid data has been inserted into any field, a descriptive error message is displayed.
Visibility
Objects can be rendered visible or invisible. Specify this using the Visibility dialog.
To access the Visibility dialog to add an action, select Visibility from the animation list and click the
Add Action button on the toolbar. To access the Visibility dialog to modify an action, select
Visibility from the animation list and click the Modify Action button on the toolbar. For a list of the
objects to which this action is applicable refer to chapter 9, Objects.
On execution of the Visibility action, the Visibility dialog is displayed:
Page 144
Release 1.2
OMRON
CHAPTER 9 – Animation
To specify a change in an objects’ visibility, enter a Boolean expression in the Digital Expression:
field. Non-Boolean expressions may be entered as long as the result is ‘TRUE’ or ‘FALSE’.
Whether the object is rendered visible or invisible when the expression is ‘TRUE’ is specified with
the Visibility State settings.
To abort the Visibility edit, click the Cancel pushbutton. By clicking the Browse pushbutton, a point
may be directly specified, as described in chapter 9, Runtime Actions. Once completed, click the OK
pushbutton. If invalid data has been inserted into any field, a descriptive error message is displayed.
Display Value (Digital)
The state of a Boolean point may be displayed using the Display Value (Digital) dialog.
To access the Display Value (Digital) dialog to add an action, select Display Status Text from the
animation list and click the Add Action button on the toolbar. To access the Display Value (Digital)
dialog to modify an action, select Display Status Text from the animation list and click the Modify
Action button on the toolbar. For a list of the objects to which this action is applicable refer to
chapter 9, Objects.
On selection of the Display Value (Digital) action, the Display Value (Digital) dialog is displayed:
An expression based on Boolean point must be entered. This expression is typed into the Digital
Expression: field. A text string to coincide with the display of a Boolean value can be entered in the
Displayed Text: field. The position of the displayed value within the text field is specified by
entering a ‘#’ character into the Displayed Text: field.
Release 1.2
Page 145
CHAPTER 9 – Animation
Note:
OMRON
To include a ‘#’ character as part of the text, insert it as an escape character. For
example, to display ‘Box # 1’ type ‘Box \# #’. Only hashes to be displayed to the
left of the # required for value display need escape characters, as the first hash
without a meta character is taken to be the point at which the value should be
displayed.
Text for Boolean State 0 and Boolean State 1 are entered in the State 0 Text: field and State 1 Text:
field.
To abort the Display Status Text edit, click the Cancel pushbutton. By clicking the Browse
pushbutton, a point may be directly specified, as described in chapter 9, Runtime Actions. Once
completed, click the OK pushbutton. If invalid data has been inserted into any field, a descriptive
error message is displayed.
Display Value (Analogue)
The state of a Real or Integer point may be displayed using the Display Value (Analogue) dialog.
To access the Display Value (Analogue) dialog to add an action, select Display Value from the
animation list and click the Add Action button on the toolbar. To access the Display Value
(Analogue) dialog to modify an action, select Display Value from the animation list and click the
Modify Action button on the toolbar. For a list of the objects to which this action is applicable refer
to chapter 9, Objects.
On selection of the Display Value action, the Display Value (Analogue) dialog is displayed:
An expression based on Real or Integer point must be entered. This expression is typed into the
Expression: field. A text string to coincide with the display of a Real or Integer value can be entered
in the Displayed Text field (this field can be updated using the Graphics Editor). The position of the
displayed value within the text field is specified by entering a “#” character into the Displayed Text:
field. The value can be displayed in its decimal form, in scientific notation, or in hexadecimal, by
selecting a Format: settings.
Page 146
Release 1.2
OMRON
CHAPTER 9 – Animation
The number of decimal places displayed can be specified by adding a “#” character for each required
place after a decimal point, e.g. #.## indicates 2 decimal places.
The text can also be left justified by setting the Left Justified setting.
Note:
To include a ‘#’ character as part of the text, insert it as an escape character. For
example, to display ‘Box # 1’ type ‘Box \# #’. Only hashes typed to the left of the #
required for value display need escape characters, since the first hash without an
escape character is taken to be the point at which the value should be displayed.
To abort the Display Value edit, click the Cancel pushbutton. By clicking the Browse pushbutton, a
point may be directly specified, as described in chapter 9, Runtime Actions. Once completed, click
the OK pushbutton. If invalid data has been inserted into any field, a descriptive error message is
displayed.
Display Value (Text)
Text may be displayed using the Display Value (Text) dialog.
To access the Display Value (Text) dialog to add an action, select Display Text Point from the
animation list and click the Add Action button on the toolbar. To access the Display Value (Text)
dialog to modify an action, select Display Text Point from the animation list and click the Modify
Action button on the toolbar. For a list of the objects to which this action is applicable refer to
chapter 9, Objects.
On selection of the Display Text Point action, the Display Value (Text) dialog is displayed:
An expression based on a text point must be entered. This expression is typed into the Text Point:
field. A text string to be displayed can be entered in the Displayed Text: field (this field can be
updated using the Graphics Editor). The position of the displayed text within the text field is
specified by entering a “#” character into the Displayed Text: field.
Note:
Release 1.2
To include a ‘#’ character as part of the text, insert it as an escape character. For
example, to display ‘Box # 1’ type ‘Box \# #’. Only hashes typed to the left of the #
required for value display need escape characters, since the first hash without an
escape character is taken to be the point at which the value should be displayed.
Page 147
CHAPTER 9 – Animation
OMRON
To abort the Display Text Value edit, click the Cancel pushbutton. By clicking the Browse
pushbutton, a point may be directly specified, as described in chapter 9, Runtime Actions. Once
completed, click the OK pushbutton. If invalid data has been inserted into any field, a descriptive
error message is displayed.
Edit Point Value (Digital)
The value of a Boolean point may be issued to the user for amendment during runtime, defined using
the User Input (Digital) dialog.
To access the User Input (Digital) dialog to add an action, select Edit Point Value (Digital) from the
animation list and click the Add Action button on the toolbar. To access the User Input (Digital)
dialog to modify an action, select Edit Point Value (Digital) from the animation list and click the
Modify Action button on the toolbar. For a list of the objects to which this action is applicable refer
to chapter 9, Objects.
On selection of the Edit Point Value (Digital) action, the dialog is displayed:
A Boolean point must be entered. This is typed into the Boolean Point: field. A text string to use as
the caption of a user dialog can be entered in the Caption: field. The range of input for the value, and
the representations of Boolean State 0 and Boolean State 1 are specified in the State 0 Text: field and
State 1 Text: field. If In Place Edit is not checked a popup dialog performs the edit. If it is checked,
the option is edited on the page with the options in a dropdown listbox.
To abort the Edit Point Value (Digital) edit, click the Cancel pushbutton. By clicking the Browse
pushbutton, a point may be directly specified, as described in chapter 9, Runtime Actions. Once
completed, click the OK pushbutton. If invalid data has been inserted into any field, a descriptive
error message is displayed.
During runtime, selecting the user input object by clicking the left mouse button results in the digital
value being edit either with the runtime User Input (Digital) dialog being displayed or the in place
listbox, based on the contents of the development version.
Page 148
Release 1.2
OMRON
CHAPTER 9 – Animation
The user is provided with an instruction, based on the Runtime Display Attributes: field (in this
example ‘Select New State’), and On and Off settings, based on the State 0 Text: and State 1 Text:
fields. The user clicks the Cancel pushbutton to abort the operation.
Edit Point Value (Analogue)
The value of a Real or Integer point may be issued to the user for amendment during runtime, defined
using the User Input (Analogue) dialog.
To access the User Input (Analogue) dialog to add an action, select Edit Point Value (Analogue) from
the animation list and click the Add Action button on the toolbar. To access the User Input
(Analogue) dialog to modify an action, select Edit Point Value (Analogue) from the animation list
and click the Modify Action button on the toolbar. For a list of the objects to which this action is
applicable refer to chapter 9, Objects.
On selection of the Edit Point Value (Analogue) action, the dialog is displayed:
Release 1.2
Page 149
CHAPTER 9 – Animation
OMRON
A Real or Integer point must be entered. This is typed into the Integer/Real Point: field. A text
string for the caption of a user dialog can be entered in the Runtime Display Attributes: field. The
limits imposed on the user for the value of the input are specified in the User Input Limits: fields.
The Display Numeric Keypad option is useful if the runtime system does not have a keyboard, i.e. it
is controlled by a touch screen or tracker ball. When a value is edited, a Numeric Keypad dialog is
displayed which allows editing by clicking on screen.
If the In Place Edit option is checked, instead of the popup editing dialog, the value can be edited on
the page in a standard Windows edit box.
To abort the Edit Point Value (Analogue) edit, click the Cancel pushbutton. By clicking the Browse
pushbutton, a point may be directly specified, as described in chapter 9, Runtime Actions. Once
completed, click the OK pushbutton. If invalid data has been inserted into any field, a descriptive
error message is displayed.
During runtime, selecting the user input object by clicking the left mouse button results in the in
place edit box or runtime User Input (Analogue) dialog being displayed, based on the contents of the
development version.
Page 150
Release 1.2
OMRON
CHAPTER 9 – Animation
CX-Supervisor provides an instruction based on the Runtime Display Attributes: field, the minimum
and maximum values allowed, based on the User Input Limits: fields, and a New Value: field, in
which the user types the desired Real or Integer value. Click the OK pushbutton to accept the value,
or the Cancel pushbutton to abort the operation. An invalid entry in the New Value field is exposed
as an error once the OK pushbutton has been clicked.
Edit Point Value (Text)
A text point may be issued to the user for amendment during runtime, defined using the User Input
(Text) dialog.
To access the User Input (Text) dialog to add an action, select Edit Point Value (Text) from the
animation list and click the Add Action button on the toolbar. To access the User Input (Text) dialog
to modify an action, select Edit Point Value (Text) from the animation list and click the Modify
Action button on the toolbar. For a list of the objects to which this action is applicable refer to
chapter 9, Objects.
On selection of the Edit Point Value (Text) action, dialog is displayed:
A text point must be entered. This is typed into the Text Point: field. A text string to use as the
caption of a user dialog can be entered in the Caption: field. Selecting the Echo Off setting ensures
that text typed at runtime appears hidden as asterisks.
The Display Keyboard option is useful if the runtime system does not have a keyboard, i.e. it is
controlled by a touch screen or tracker ball. When a value is edited, a Keyboard dialog is displayed
which allows editing by clicking on screen.
If the In Place Edit option is checked, instead of the popup editing dialog, the value can be edited on
the page in a standard Windows edit box.
Release 1.2
Page 151
CHAPTER 9 – Animation
OMRON
To abort the Edit Point Value (Text) edit, click the Cancel pushbutton. By clicking the Browse
pushbutton, a point may be directly specified, as described in chapter 9, Runtime Actions. Once
completed, click the OK pushbutton. If invalid data has been inserted into any field, a descriptive
error message is displayed.
During runtime, selecting the user input object by clicking the left mouse button results in the in
place edit box or runtime User Input (Text) dialog being displayed, based on the contents of the
development version.
The user is provided with an instruction based on the Runtime Display Attributes: field, and a field in
which the user enters the desired text. Click the OK pushbutton to accept the value, or the Cancel
pushbutton to abort the operation. An invalid entry typed in the editable field is exposed as an error
once the OK pushbutton has been clicked.
Common Colour Palette
If an object or action has a colour associated with it, the colour can be changed by clicking on the
sample of the colour in the dialog which describes the object or action. The Colour Palette dialog is
displayed so that a new colour can be specified.
Page 152
Release 1.2
OMRON
CHAPTER 9 – Animation
A colour can be selected by clicking on one of the palette colours. This becomes the selected colour,
and is denoted as such in the Selected Colour: field. Alternatively, a colour can be selected by
specifying a colour name or number in the Colour Name: field. The selected colour within the
palette can be mixed by using the red, blue and green scroll bars to the right of the palette.
Each colour in the colour palette is numbered from 0 to 65, number 0 located in the top-left position
of the palette, with numbers reading consecutively across, then down, with colour number 65 in the
bottom-right position of the palette. Additionally, colour numbers 0 to 19 are named — for instance,
colour number 0 is named “black”.
Colours 0 to 15 inclusive are system colours and cannot be mixed. Although it is possible to mix
new colours using the scroll bars, it is not possible to save such changes from this palette. To ensure
new colours are saved, use General Settings from the Project menu.
Note:
Release 1.2
Using a 16 colour-based screen resolution (consult the Microsoft Windows
documentation for further information) colours 16 to 65 are dithered from the
sixteen base colours. Higher colour-based resolutions are not dithered.
Page 153
CHAPTER 9 – Animation
Page 154
OMRON
Release 1.2
OMRON
CHAPTER 10 – Recipes
CHAPTER 10
Recipes
This chapter describes CX-Supervisor recipes and the procedures associated with the creation,
amendment and removal of recipes using the Recipe Editing facility. The use of recipes during the
running of a project is also described.
What is a Recipe?
A recipe is a means of preparing a sequence of steps which can be repeated verbatim as and when
required. A typical use for a recipe is to initialise some point data values prior to the commencement
of a particular operation under the control of a CX-Supervisor project.
A CX-Supervisor recipe consists of one or more ingredients, each of which relates to a point. Each
ingredient assigns a value to a point by means of a target value.
A suite of CX-Supervisor recipes may be created for any project. In runtime, the recipes are a great
time-saver that eliminate mistakes that may otherwise be made were the repetitive tasks they perform
left to human endeavour.
It is possible to achieve simple point initialisation using the CX-Supervisor script language. This
approach works perfectly well for relatively straight-forward applications. However, further
functionality is provided using the recipe system, such as the ability to modify a recipe while the CXSupervisor project is being executed in runtime.
Recipe Components
Before proceeding any further with the description of recipes, some basic recipe terminology must be
introduced:
♦
Recipe. A recipe is a set of pre-defined steps used to perform a particular task. A CXSupervisor project may contain none or many. Recipes are defined in the development
environment and executed, or downloaded, in the runtime environment.
♦
Ingredient. Each recipe consists of at least one ingredient. Each ingredient must be related to an
existing point.
♦
Target Value. An ingredient must specify a target value for its related point. This is the value to
which the point is set in runtime when the recipe is downloaded.
♦
Validation Code. Recipe validation code is CX-Supervisor script code which is used to check
point values before downloading a recipe.
♦
Download. A recipe is downloaded during runtime. This process involves identifying the
appropriate recipe and executing the validation code, if any exists. The download is complete
when each ingredient has set its point to the target value.
Release 1.2
Page 155
CHAPTER 10 – Recipes
OMRON
Viewing Recipes in the Recipe Editor
The Recipe Editor allows the creation, editing, copying and deletion of recipe definitions. To use the
Recipe Editor, CX-Supervisor must currently have a project open. If no project is currently open,
select Open from the Project menu to open a previously saved project, or select New from the Project
menu to create a new project.
To open the Recipe Editor dialog, click the Recipe Editor button on the toolbar.
Display the Recipe Editor as described in the previous chapter. An example of the Recipe Editor
dialog is shown below:
Recipes are displayed in three columns: Recipe, Access Level and Validation Script. Recipes are
usually listed in alphabetical order by recipe name, although the ordering can be changed so that the
entries are listed according to any of the three column titles.
For example, to see the recipes listed alphabetically by security access level, simply click on the
Access Level field.
The widths of the recipe fields can be widened or narrowed as required using the
mouse to drag the column boundaries.
Select the Large Icons button to view details with large icons.
Select the Small Icons button to view details with normal icons.
Select the List button to view details as a list.
Select the Details button to view details as a list including recipe, access level and validation
script. The details can be sorted in ascending order by clicking once or in descending order
by clicking twice, in the appropriate field.
A summary of recipe information is available by selecting the Recipe Information button
from the toolbar.
The resultant dialog shows the overall number of recipes in the project. To exit the dialog click the
Close pushbutton. The Recipe Information dialog is shown as follows:
Page 156
Release 1.2
OMRON
CHAPTER 10 – Recipes
Creating a New Recipe
Open the Recipe Editor as described in chapter 10, Viewing Recipes in the Recipe Editor.
To add a new recipe, select the Add Recipe button from the toolbar. This results in the Add
Recipe dialog being displayed.
Once all the information has been provided for the new recipe, selecting the OK pushbutton adds the
new recipe definition to the project, whilst the Cancel pushbutton aborts this add operation.
Note:
Release 1.2
The short-cut keyboard combinations for Cut, Copy and Paste operations are valid
within the Add Recipe dialog. Highlight part or all of a field and type <Ctrl>+X to
cut the text or <Ctrl>+C to copy the text; insert the cursor at the desired field and
type <Ctrl>+V to paste the text. Since the cut and copy operations store the
information in the Windows Clipboard, they may be pasted to another dialog or
application.
Page 157
CHAPTER 10 – Recipes
OMRON
Recipe Configuration Attributes
The name of the recipe is entered in the Recipe Name: field. The recipe name can be constructed
using any alphanumeric characters. This field is visible from the Recipe Editor dialog.
A recipe description may be inserted in the Description: field. To start a new line, press
<Ctrl>+<Return>. Any characters are valid and up to 255 characters may be entered in the text field.
This field is also visible from the Recipe Editor dialog.
Recipe Ingredients
The recipe ingredients are added using the Add Ingredient pushbutton in the Add Recipe dialog to
display the Add Ingredient dialog, as follows:
Enter a suitable ingredient name in the Ingredient Name: field. This name should be unique and
meaningful and identify the particular ingredient being added to the recipe.
Enter the name of a point which is initialised by this ingredient in the Link to Point: field. The
adjacent Browse pushbutton may be used to display the Select Required Item dialog, which provides
a list of points from which the selection may be made. The Select Required Item dialog also provides
an Add Point pushbutton which allows a new point to be added. See also chapter 3, Points. The
Quantity/Expression field is used to define the value which is assigned to the point by this ingredient.
This may be a fixed value, such as 50 as in the above expression, or it may be any valid CXSupervisor script language expression featuring one or more point names.
Page 158
Release 1.2
OMRON
CHAPTER 10 – Recipes
The Editable Value at Runtime setting determines whether the target expression may be changed at
runtime when the recipe is downloaded. Only expressions featuring a fixed value may be edited in
this way; expressions featuring point names may not be edited at runtime.
Select the OK pushbutton to add the ingredient to the recipe, or the Cancel pushbutton to abort this
part of the operation.
Recipe Validation
Recipe validation is an optional safety check which may be made in runtime as the recipe is about to
be downloaded. If the validation fails, the recipe is not downloaded.
If no validation is required, make sure the Validate Recipe Before Download setting is set to ‘OFF’.
If validation is required, check this box and then click the Validation Code pushbutton to display the
Script Editor dialog:
Release 1.2
Page 159
CHAPTER 10 – Recipes
OMRON
Enter the recipe validation code using any standard CX-Supervisor script language constructs. The
validation code should check any possible invalid point value or error condition. The point value
being checked is the value of the ingredient about to be downloaded, or the current point value if the
point is not an ingredient of the recipe being downloaded.
In the event of a failure, the script language should perform a premature <Return>. This has the
effect of failing the recipe validation check and abort the attempt to download the recipe.
The recipe validation code should not contain any command which requires user input (e.g. a
Message command). This is because the validation script would not have been completed (and
appropriate action taken) at the time that user input is requested. Instead, if a message box is
required, then a point should be used as an error status value, and set to an appropriate value. This
point can then be checked in an ‘on condition’ script and the appropriate message displayed from
there.
If the validation code exits normally, the recipe is downloaded in the normal way.
Updating an Existing Recipe
Open the Recipe Editor dialog as described in chapter 10, Viewing Recipes in the Recipe Editor.
Page 160
Release 1.2
OMRON
CHAPTER 10 – Recipes
To modify an existing recipe, highlight the recipe entry from the recipe list and select the
Modify Recipe button from the toolbar.
This results in the Modify Recipe dialog being displayed, a dialog based on the Add Recipe dialog, as
shown below:
The selected recipe can be redefined as described in chapter 10, Creating a New Recipe.
The Modify Ingredient and Delete Ingredient pushbuttons on this dialog respectively allow the
highlighted ingredient to be modified, or deleted (following confirmation).
Once all the information has been provided for the updated recipe, clicking the OK pushbutton saves
the recipe details, whilst the Cancel pushbutton aborts this modify operation.
Release 1.2
Page 161
CHAPTER 10 – Recipes
OMRON
Copying an Existing Recipe Definition
Open the Recipe Editor dialog, as described in chapter 10, Viewing Recipes in the Recipe Editor.
To copy an existing recipe, highlight the recipe from the recipe list and then type <Ctrl>+C. This
creates a copy of the recipe definition on the clipboard. To paste the recipe definition back in to the
current project, type <Ctrl>+V. The cut, copy and paste operations in the Edit menu may also be
used. The Recipe Editor ensures the name of the recipe is unique by appending a number to the
name. For example, if the original recipe name was “Recipe”, the name of the pasted recipe is
“Recipe1”. All other properties of the pasted recipe remain the same as the original recipe definition.
It is possible to copy many recipes at once by highlighting all the desired recipes in the recipe list.
Press and hold the <Ctrl> key and use the mouse to select recipe definitions one by one, or press and
hold the <Shift> key and use the mouse to select blocks of recipe definitions. Once the desired
recipes have been highlighted, the recipe definitions may be copied and pasted in the usual way.
Deleting an Existing Recipe
Open the Recipe Editor dialog, as described in chapter 10, Viewing Recipes in the Recipe Editor.
To remove an existing recipe, highlight the recipe from the recipe list and select the Delete
Recipe button from the toolbar.
A confirmation dialog is displayed. Click the Yes pushbutton to remove the definition, or the No
pushbutton to abort the delete operation.
Recipe Security Levels
A recipe may be assigned a security level governing which level of users are allowed to download the
recipe in runtime. The available security levels are shown below in descending order:
♦
Designer;
♦
Manager;
♦
Supervisor;
♦
Operator;
Page 162
Release 1.2
OMRON
CHAPTER 10 – Recipes
♦ All Users.
To assign a security level to a recipe, display the Recipe Editor dialog. Then select the recipe to
which the security level is applied. With the recipe highlighted from the list, click the Security Level
field on the toolbar.
Select the required security level from the list. The selected security level is then applied to the
recipe. To change the security level, click the Security Level field again and choose a different
security level from the list.
Printing Recipes
Print Setup
The Recipe Editor can be printed in the same way pages can. Before printing, ensure that the printer
has been set up correctly. To check the printer settings, refer to chapter 2, Pages.
Print Preview
To preview the page before printing, select Print Preview from the File menu.
Refer to chapter 2, Pages regarding the use of the Print preview display.
Printing
To print the contents of the Recipe Editor, select the Print button from the toolbar.
Refer to chapter 2, Pages regarding the use of the Print dialog.
It is possible to print the details of a recipe including a list of all the ingredients, points and
expressions which comprise the recipe. To do this, display the Recipe Editor dialog as described
earlier and then highlight the appropriate recipe from the list of recipes. Click the Print Recipe
button on the toolbar to send a copy of the recipe to the printer. The recipe is formatted similar to the
following example:
Recipe: Coffee(British)
Description: Makes weak, washy, British style coffee.
Access Level: All Users
Ingredient
milk(ml)
coffee(g)
sugar(g)
water(ml)
Release 1.2
Point
milk
coffee
sugar
water
Expression
50
3
0
250
Editable
Yes
Yes
Yes
Yes
Page 163
CHAPTER 10 – Recipes
OMRON
Using Recipes in Runtime
Recipes defined using the Recipe Editor in the development environment can be accessed in runtime
using the Recipe Viewer. Recipes may be downloaded using the Recipe Viewer.
Recipe Viewer
The Recipe Viewer can be displayed in one of two ways in the runtime environment. It may be
displayed by any CX-Supervisor script code attached, for example, to a pushbutton. The function
call is simply ‘DisplayRecipes()’.
The Recipe Viewer may also be displayed using the floating menu. The floating menu needs to be
configured to display the Recipes option. This is done in the development environment and
explained in chapter 6, Projects.
The Recipes dialog is displayed as follows:
The Recipe Viewer is similar to the Recipe Editor, however there are some differences in
functionality and appearance:
To remove an existing recipe, highlight the recipe from the recipe list and select the Delete
Recipe button on the toolbar. A confirmation dialog is displayed. Click the Yes pushbutton
to remove the definition, or the No pushbutton to abort the delete operation. Note that
recipes created in the development environment may not be deleted in the runtime
environment. The delete operation only affects recipes copied and saved in the runtime
environment.
To modify an existing recipe, highlight the recipe from the recipe list and select the Modify
Recipe button from the toolbar. The Modify Recipe dialog is displayed as follows:
Page 164
Release 1.2
OMRON
CHAPTER 10 – Recipes
This runtime version of the dialog is rather more limited in the power it offers than the equivalent
dialog in the development environment; this is so that recipes which have been painstakingly created
in the development environment cannot be accidentally overwritten or destroyed in the runtime
environment. The two pushbuttons unique to the Runtime of the dialog are Modify Target and Save
Recipe As.
With the appropriate ingredient selected from the list, clicking the Modify Target pushbutton allows
the target value to be modified by means of the Modify Ingredient dialog, shown below:
The target value for this ingredient may be changed by entering the new value in the New Target:
field. Selecting the OK pushbutton accepts the change, choosing the Cancel pushbutton aborts the
change.
Note:
Release 1.2
The new target value is applied only to this recipe download. No permanent change
is made to the recipe definition itself.
Page 165
CHAPTER 10 – Recipes
OMRON
The Save Recipe As pushbutton displays a simple dialog prompting for a name to use for the new
recipe.
Clicking the OK pushbutton creates a new recipe with the name specified. Choosing the Cancel
pushbutton aborts the save operation. A recipe created using this dialog is added to the available list
of entries displayed in the recipe dialog. The newly saved recipe is also available in the development
environment using the Recipe Editor.
Note that it is possible to change the name of an existing recipe in runtime simply by typing a new
name in the Recipe Name: field of the Modify Recipe dialog and then clicking the OK pushbutton.
The re-named recipe appears in the available list of entries displayed in the Recipes dialog and is also
available in the development environment using the Recipe Editor.
To download an existing recipe, highlight the recipe from the recipe list and select the
Download Recipe button from the toolbar. See chapter 10, Downloading a Recipe for more
information.
To upload an existing recipe, highlight the recipe from the recipe list and select the Upload
Recipe button from the toolbar. See chapter 10, Uploading a Recipe for more information.
Click the Print Recipe toolbar button to send a copy of the recipe to the printer. See chapter
10, Printing Recipes for a typical example of the formatted output.
A summary of recipe information is available by selecting the Recipe Information button
from the toolbar. The Recipe Information dialog is displayed (see chapter 10, Viewing
Recipes in the Recipe Editor for an example).
Downloading a Recipe
There are two ways of downloading a recipe definition in runtime. The first method is to use a CXSupervisor script function attached to a graphical object on a page, such as a push button. The
function call is:
DownLoadRecipe(“<NameOfRecipe>“)
The other way to download a recipe, is to display the Recipe Viewer as described in the
previous chapter. Highlight the desired recipe from the recipe list and click the Download
Recipe pushbutton. The Download Recipe dialog is displayed as follows:
Page 166
Release 1.2
OMRON
CHAPTER 10 – Recipes
The Modify Target pushbutton allows the target value for an ingredient to be modified by means of
the Modify Ingredient dialog (shown above). An ingredient must already be selected from the list of
ingredients for this recipe. Any change to the target value is of a temporary nature and is not
permanently changed in the recipe definition. Any number of ingredients may be modified in this
way before the recipe is downloaded.
Selecting the OK pushbutton attempts to download the recipe. If for some reason the recipe
definition can’t be found, the following error message appears: “Unable to find recipe”.
One recipe download must be completed before another recipe download is started. If a recipe
download is already in progress when another is started, the following error message appears: “A
recipe download is currently in progress”.
If any validation code has been entered for this recipe, the validation is conducted first. If the
validation is successful, the recipe is downloaded. If the validation fails, the recipe is not
downloaded and the following error message appears: “Unable to download selected recipe”.
If there is no validation code to execute, the recipe is downloaded anyway. The download process
consists of setting each ingredient to its specified target value.
The download may fail at this stage if there are problems communicating with a PLC. A
communications failure results in the error message “Downloading recipe failed”. A delay in
response from the PLC of more than one minute results in the error message “Recipe transfer timed
out”.
When the recipe download is complete, all the ingredients are saved and the CX-Supervisor runtime
environment continues to run in the normal manner. An event is logged stating that the recipe was
successfully downloaded.
Uploading a Recipe
There are two ways of uploading a recipe definition in runtime. The first method is to use a CXSupervisor script function attached to a graphical object on a page, such as a push button. The
function call is:
UpLoadRecipe(“<NameOfRecipe>“)
Release 1.2
Page 167
CHAPTER 10 – Recipes
OMRON
The other way to upload a recipe, is to display the Recipe Viewer as described in the
previous chapter. Highlight the desired recipe from the recipe list and click the Upload
Recipe pushbutton. The Modify/Save Upload Recipe dialog is displayed as follows:
The Modify Target pushbutton allows the target value for an ingredient to be modified by means of
the Modify Ingredient dialog. An ingredient must already be selected from the list of ingredients for
this recipe. Any change to the target value is saved in the recipe definition. Any number of
ingredients may be modified in this way when the recipe is uploaded.
Selecting the OK pushbutton will upload the recipe. If for some reason the recipe definition can’t be
found, the following error message appears: “The recipe failed its validation checks. Upload
aborted”.
Each recipe upload must be completed before another can be started. If a recipe upload is already in
progress when another is started, the following error message appears: “A recipe Upload or
Download is currently in progress”.
The upload may fail at this stage if there are problems communicating with a PLC. A
communications failure results in the error message “Uploading recipe failed”. A delay in response
from the PLC of more than one minute results in the error message “Recipe transfer timed out”.
When the recipe upload is complete, all the ingredients are saved and the CX-Supervisor runtime
environment continues to run in the normal manner. An event is logged stating that the recipe was
successfully uploaded.
Page 168
Release 1.2
OMRON
CHAPTER 11 – Data Logging
CHAPTER 11
Data Logging
This chapter describes the CX-Supervisor data logging facilities including how to configure items to
be logged, the logging of data and the viewing and exporting of recorded data.
What is Data Logging
The concept of the Data Logger is the ability to define a number of points and expressions during
development which may be recorded while the CX-Supervisor project is being executed in runtime.
These events may be viewed at runtime and recorded for future evaluation. They may also be
exported to other programs such as Microsoft Excel.
The recorded events are stored in one or more Data Sets, which can then be viewed using the Data
Log Viewer. The events to be recorded are defined by the developer and any number of Data Sets
may be used to record specific areas or types of events either automatically at runtime or as specified
by the developer.
As an aid to viewing a number of particular events in isolation Data Sets can be subdivided into data
Groups. Specific areas of related data can then be stored in these groups which can then be viewed
either singly or with other groups within a Data Set.
The main elements of the CX-Supervisor Data Logger are:
♦
Data Logger Editor: used to configure items to be logged
♦
Data Logging at Runtime: the actual logging of the data
♦
Data Log Viewer: used to view the logged data
♦
Remote Data Viewer: enables viewing separately from the runtime system
♦
Data Log Export facility: enables export to other programs (e.g. MS Excel)
♦
Script Functions: gives full control over the logging process
Data Log Editor
Configuring Data Sets and Logging Settings
The Data Sets, data Groups and Items to log are configured from the Logging Tab on the
bottom of the Development Workspace editor. Items are edited using a right mouse-button
context sensitive menu. The option available from the menu are:
♦
Edit: enable the parameters of the selected Data Set, Group or Item to be edited.
♦
Cut, Copy, and Paste: enables the selected Item to be cut or copied and then pasted into a Data
Set or Group.
♦
Delete: will delete the selected entry.
Release 1.2
Page 169
CHAPTER 11 – Data Logging
♦
OMRON
Add DataSet, Add Group and Add Item: enables new Data Sets, Groups and Items to be added
to the selected entry.
The functionality of the Items is determined by their expression. If the expression is a single point
name, the item is shown as the same type as the point as configured in the point editor, i.e. memory,
input, output or input/output. If the expression contains calculations, constants and/or multiple point
names, the item is shown as a script calculation.
Adding/Editing Data Set Properties
The Add/Modify Data Set properties dialog is displayed when either the Add Data Set or the Edit
(an existing Data Set) option is selected from the menu.
Page 170
Release 1.2
OMRON
CHAPTER 11 – Data Logging
Data Set Properties
The Data Set Name field enables the Data Set to be referenced with a meaningful description both in
the Workspace view, and also from the script language. It also forms the prefix for the file name. A
maximum of 26 characters is allowed.
The Period fields allow a period to be entered in Hours, Days, or Months and defines the period of
data to be grouped into a single file. For example, if the Period is set to 1 month, any data logged for
the current month is saved to the same data file, even when the system is stopped and restarted.
When logging spans a Month boundary the data file is closed, and a new file started and given
sequential file name. This allows easy archiving and backup of the logged data. The start of a new
data file is always synchronised to a natural boundary, e.g. for months - the 1st of the month, for days
– 24.00 hours and for hours - on the hour.
The No. Of Files to Keep entry determines the maximum number of data files that are to be kept.
Once the number of files kept has reached the value entered, as each new file is created the oldest file
is deleted. For example, to keep process data for 2 years, you could keep 24 files of 1 month period.
The file names are generated automatically based on the Data Set name, plus a suffix which is
incremented by one as each new file is generated.
If the Keep all Files option is checked the data files management is disabled and no files will be
deleted.
The Start Logging on Application Startup checkbox controls the logging of the Data Set. When
selected, all the Items in the Data Set start logging when the system is started, and stop logging when
the system is stopped. If this option is not selected, then logging must be controlled by the Start/Stop
logging script functions as required by the developer.
Editing Item Properties
The Add/Modify Item properties dialog is shown when adding a new Item, or editing an existing
one.
Release 1.2
Page 171
CHAPTER 11 – Data Logging
OMRON
Item Properties
These options enable an items name and associated expression to be entered. Its data type can be
selected and if required a deadband value can be applied to the measured value.
The Item Name field allows the Item to be given a meaningful name. The entry should be kept short
but also be logical for clarification. A maximum of 26 characters is allowed.
The Expression field defines the point name or expression that will be logged. The Browse button
allows easy point selection. For details on how expressions or points are formulated Refer to chapter
3, Points.
The Data Type field determines the type of data to be logged. Select either Boolean, Integer or Real.
For points, this is automatically picked up from the points database. For expressions, the required
type must be selected.
The Deadband field enables a percentage limit or ‘Deadband’ to be applied to the logging expression.
This allows the value of the expression to change within the percentage limit without being logged.
This is particularly useful when logging analogue values which are subject to noise. Each sample is
checked (when the value changes for ‘On Change’ sampling, or every log period for ‘On Interval’)
against the last logged value. While the value varies within the deadband, the values are ignored.
Immediately the value exceeds the deadband limits the new value will be logged. This may
dramatically reduce file size, and ease analysis.
Entering a value of 0%, i.e. no deadband, will cause every sample to be logged.
Page 172
Release 1.2
OMRON
CHAPTER 11 – Data Logging
Sample Rate
The sample rate options are used to determine how data will be recorded, select either on change or
on interval. The default is interval.
When the On Change option is selected data will be logged only when the value actually changes.
This ensures all transient information is logged - even if changes occur faster than maximum sample
rate, and also ensures periods of inactivity do not generate duplicated data.
The On Interval sample rate option enables the data values to be logged at regular intervals. Enter
the interval as a number and from the pick list select the form, e.g. ‘5 Second’. This method
guarantees the value is checked and recorded at every interval. However transients occurring
between sample periods are not recorded, which depending on the application may be a benefit.
Scale
The scale fields enable the graph upper and lower limits to be set and a scale label entered for the
selected item.
Enter the Minimum value as the lower limit to be shown on the graph for this item.
Enter the Maximum value as the upper limit to be shown on the graph for this item.
Enter the Scale Label to be displayed. This is a text field the contents of which are displayed by the
Y scale of the graph. The entry should be kept short but also be logical for clarification.
Editing Items
Copy, Cut, Paste Options
The Copy, Cut and Paste options follow the windows convention and enable a selected Item to be
copied or cut from one Data Set Group and then pasted into another. As Item names within a Data
Set must be unique, when a copied Item is pasted back into the same Data Set the name is given a
numerical suffix.
New or existing Items can be renamed and have their parameters edited by high lighting the Item and
then selecting the Edit option from the popup menu. When the Modify Item dialog appears edit the
appropriate parameters in the normal way.
Adding/Renaming Groups
The adding or renaming of Data Set groups follows the windows convention. New Groups are added
by selecting the Data Set to which the group is to be added and then selecting the Add Group option
from the popup menu. The new Group is automatically placed in the correct position in the Data Set
and given a default group number. New or existing Groups can be renamed by first high lighting the
current group name and then selecting the Edit option from the popup menu. When the edit box is
displayed the name can then be edited in the normal way. A maximum of 26 characters is allowed.
Unwanted groups can only be Deleted, they can not be cut and pasted.
Release 1.2
Page 173
CHAPTER 11 – Data Logging
OMRON
Data Logging at Runtime
Overview
All data logging is performed on Items, which are stored in a Data Set. The System can contain
many Data Sets and each Data Set can contain many Items. Each Data Set will have its own set of
files when the System is run (see the chapter 11, File Management). The amount of data that is
stored in a single Data Set file is determined by the specified period when the Data Set is created.
File Management
Data Logging Directory
All data log files are stored in the directory “Data Logging” separate from the CX-Supervisor files.
This directory is created automatically when the project runs for the first time. A sub-directory is
used as a safeguard against the accidental deletion of important files by the automatic purge
mechanism and to prevent the project directory from becoming cluttered with data files.
For example, if the CX-Supervisor project is in a directory called C:\CX-Supervisor\Project then,
when the project runs for the first time a new directory called C:\CX-Supervisor\Project\Data Logging
will be created to hold the data log files.
Data Logging Files
Each Data Set has its own set of files. The following conventions have been adopted in order to
identify the various files and add time and date information.
Data Log files are assigned the file extension .dlv “Data Log Values” and the format of the filename
is:
<Data Set Name><Time Stamp>.dlv
The Time Stamp is in the format: [YYYY MM DD HH]”
where
YYYY = Year in the form 1999
MM = Month in the form 01 (January)
DD = Day of the month in the form 01 – 31
HH = Hours in the form 00 –23
Daylight time saving is automatic.
For example:
Data Set 1 Miller[1999012015].dlv
A new log file will be created automatically whenever the preceding file has expired the timestamp.
The timestamp is also used to distinguish between files in the same Data Set. The time period for
each file is determined by the options selected when the Data Set was created. The minimum time
period for a Data Set file is one hour commencing on the hour.
Page 174
Release 1.2
OMRON
CHAPTER 11 – Data Logging
Note:
Do not rename any log files while they are in the Data Logging directory or the File
Management System will not work correctly. The File Management System relies
on the strict format of the Data Log files to determine which file to open as Live
and which file(s) to delete during purging and also for performing ‘previous/next’
file searches in the Data Log Viewer.
Note:
Additional files should never be copied into the Data Logging directory as the
automatic purging mechanism may delete all the log files.
Number of files in a Data Set
When a Data Set starts logging a file will be created to hold the logged items, this file is known as a
‘Live’ or ‘Active’ log file (There is only one Live file in a Data Set file set). When the time period
for a Data Set log file expires a new file is created with a more recent Timestamp, this file then
becomes the ‘Live’ file and the previous file is now known as a ‘Dead’ log file. Over a period of
time there can be many ‘Dead’ files in a Data Set but only one live one. If a limit has been set on the
number of dead files to be kept when this number is reached the oldest file will be purged
automatically as each new file is created.
The number of dead files to be kept for a particular Data Set is managed automatically by specifying
the ‘Number of Files to Keep’ from the Data Set Properties Parameters when a Data Set is created.
This field is only enabled when the ‘Keep all files’ check box is ‘unchecked’.
Note:
There will always be one Live file for each Data Set.
For example, if the number of files to keep is set to 24 then there the system will keep 24 Dead files
and one Live file, i.e. 25 files in total.
WARNING: No backups are taken when a file is purged. If you wish to keep any data you
must ensure that backups are taken before purging occurs.
If the ‘Keep all files’ check box is checked no automatic purging will take place and the System will
store all the Dead files created until the disk is full.
Dead files can be copied, moved, deleted etc. as they will not be written to again by the System.
Live files may be copied (i.e. backed up to another directory) while the Log file is open but they
cannot be moved or deleted as they are locked by the System. In order to delete or move a live file it
must first be closed. See Opening and Closing Log Files.
Invalid Data Log Files
Data log files generated during one project sessions will continue to be used in subsequent sessions, if
they are still live. For example, if a system runs during the day and is shut down at night, then a Data
Set with a duration of 7 days will use the same file for the whole 7 days.
Release 1.2
Page 175
CHAPTER 11 – Data Logging
OMRON
If a session is halted and Data Set Items changed, deleted or new ones added it is not valid to
continue using the existing file. When the session is restarted and Data Set file opened CXSupervisor checks to see if there are any differences between the current Data Set and the Data Set
stored in the file. If any differences are detected the System will mark the existing file as invalid by
altering the Timestamp brackets from “[ ]” to “{{ }}” and create a new file.
For example, if a file Batch1[2000032922].dlv is detected as being invalid it will be
renamed Batch1{{2000032922}}.dlv. A new Batch1[2000032922].dlv file will
then be created to log the new data.
If the file Batch1{{2000032922}}.dlv already exists then the current invalid file will be
renamed Batch1{{2000032922}}_1.dlv and so on.
This is most likely to occur during the development of an application when Data items are
continually being amended and tested.
Invalid files are not part of the Data Set files and can not be purged or found by the File Management
‘next’ or ‘previous’ searches. The data recorded in these files is not lost and can be viewed using the
Data Log Viewer and exported from them using Export Log. Invalid files can only be deleted using
Windows explorer.
Data Set Period Examples
The following examples show how the specified period (Hour(s), Day(s), Month(s)) is implemented
while the System is running:
1) Data Set period = Hours
If a Data Set named CV500 starts logging at 12:30 on the 7th March 1999 with a period of 6 hours,
the following files will be created:
CV500[1999030712].dlv
If the s7stem is left running the Data Logging directory will contain the following files:
CV500[1999030712].dlv
CV500[1999030718].dlv
CV500[1999030800].dlv
CV500[1999030806].dlv
....
....
The first file will only contain 5.5 hours of Data because the minimum resolution is one hour and the
file was created on the half-hour, all subsequent files will contain the full six hours of data.
2) Data Set period = Days
If a Data Set named Batch1 starts logging at 23:00 on the 29th December 1999 with a period of 1 Day,
the following files will be created:
Page 176
Release 1.2
OMRON
CHAPTER 11 – Data Logging
Batch1[1999122923].dlv
If the system is left running the Data Logging directory will contain the following files:
Batch1[1999122923].dlv
Batch1[1999123000].dlv
Batch1[1999123100].dlv
Batch1[2000010100].dlv
....
....
The first file will only contain 1 hour of data, all subsequent files contain the full 24 hours of data.
3) Data Set period = Months
If a Data Set named Shifts starts logging at 22:00 on 29th February 2000 with a period of 2 Months,
the following file will created:
Shifts1[2000032922].dlv
If the system is left running the Data Logging directory will contain the following files:
Shifts[2000050100].dlv
Shifts[2000070100].dlv
....
....
The first file will only contain 1 month and 2 hours of data, all subsequent files contain the full 2
Months of data.
Data Records
There are two types of records that are stored in a Data Log file for each Item logged these are
Events (or breaks) and the Actual Data.
Event/Break Records
Event records currently consist of the following fields:
Event, Date, Time
Event = Open | Close | Clear | Start | Stop
Events have no associated data
Data Records
Data records currently consist of the following fields:
Type, Date, Time, Milliseconds, Data
Type = Normal | Error
Data = Boolean | Integer | Real
Release 1.2
Page 177
CHAPTER 11 – Data Logging
OMRON
Data Log Viewer Component
Invoking the Data Log Viewer
The Data Log Viewer can be invoked by
Selecting Data Log Viewer from the popup menu (if privileged) in the runtime.
From script function ‘OpenLogView’ with the Data Set and Traces to show as arguments, and also
closed by ‘CloseLogView’ script function.
From an external program.
Viewing Logged Files
The Data Log Viewer looks like this:
The window shows a graphical representation of the recorded data.
Page 178
Release 1.2
OMRON
CHAPTER 11 – Data Logging
Features:
♦
The Data Set viewed is the name passed as an argument with the script function, or a userselected Data Set.
♦
On start-up, a dialog allowing selection of traces to view from the Data Set will be shown. Up to
10 analogue traces and 50 digital traces may be shown at once. Alternatively, script parameters
can be used to automatically select the traces to show.
♦
On display, the viewer displays:
™ the latest data file for this Data Set
™ the X axis set to the Data Set’s period
™ Y Axis set to full scale for the first trace.
♦
The selected analogue traces are shown overlaid.
♦
Boolean points are displayed in a separate view
♦
The X Axis shows true Date and Time, as the local time on the logging system. Remote analysis
within different time zones will show the same dates and times. Logging of local time means
adjustment of PC time and daylight saving are handled.
♦
Key shows trace colour, name, and value at the cursor. Selected trace has a “>” before the name.
Clicking on other trace details selects other traces.
♦
Scale shows Minimum value, Maximum value and scale label of selected trace, with
intermediate scales.
♦
A cursor allows data to be read off the graph. Pressing Ctrl and cursor keys allows moving
between logged data.
♦
A Zoom In and Zoom Out facility (Time and Range), plus X & Y axis scrolling, are available.
♦
‘Previous’ (
♦
The ‘Refresh’ button reloads the file from disk.
♦
A ‘Live’ option is used to show the latest data, and keep it up to date.
♦
Data can be exported to CSV files or to text.
♦
The current screen can be printed, or print previewed, in colour.
♦
The traces shown using trace selection dialog as shown initially can be changed using the “Select
item” facility.
) and ‘Next’ (
) buttons load data files for the previous and next time period.
Remote Data Log Viewer
Data log files are not restricted to a machine that has CX-Supervisor installed on it. CX-Supervisor is
supplied with a “Data Log Viewer” application that enables all the View and Export facilities (with
the exception of Live updates) to be carried out on .dlv files that have been transferred to a stand
alone machine.
Release 1.2
Page 179
CHAPTER 11 – Data Logging
OMRON
Data Log Export Facilities
Exporting Data via the Export Dialog
All the export facilities described in the ExportLog function can be carried out from the Export
dialog, which can be invoked from the CX-Supervisor right menu, script or the Data Log Viewer:
Options include the following:
USE GENERATED FILES
If this option is checked, then filenames will be automatically created, otherwise a “Save File As”
dialog will be displayed.
EXPORT TYPE
Controls whether export should be as comma-separated values files or as text.
ADDITIONAL INFORMATION TO EXPORT
Controls whether breaks, date, time and milliseconds are exported.
Generation of Comma Separated (CSV) Files
Both the ExportLog script function and the Export Dialog use the following conventions for
automatically generating comma-separated values files for export:
Page 180
Release 1.2
OMRON
CHAPTER 11 – Data Logging
All generated CSV filenames will contain at least the <Data Set name> + <timestamp> and a
.CSV extension. CSV is a format that is recognised directly by spreadsheet packages such as Excel
and can therefore be opened and viewed with this application.
e.g.
MyData Set1999011214.csv
No [ ] characters are used in the timestamp. This is for two reasons:
A. Applications like Excel seem to complain about them being there.
B. Less likely to be confused will .dlv files during searches/purges
During the generation of files then obviously duplication of names can occur. To avoid this the
following convention is used:
“_nnn” will be appended to any duplicate filenames, to make them unique, where nnn = 1 to 999. (If
you run out numbers the export will fail, tidying up will remedy the problem).
Generated names depend on whether a single item, or multiple items, are selected for export:
Single Selections
If a single item is selected for export i.e. “Item3” in the root directory of “MyData Set” then the
following file will be generated:
MyData Set1999011214Item3.csv
Multiple Selections
On Interval Items
If a multiple selection of “on interval” items with the same interval is made then the name of the
parent directory will be used e.g. if the items live in “Group1” the following file will be generated:
MyData Set1999011214Group1.csv
The file will contain a column for each item selected and they will share the Date and Time fields.
Note:
The milliseconds field will only be valid for one of the Items, and should therefore
be filtered out for this type of grouping.
If a multiple selection of “on interval” items, with different intervals is made then any items with the
same interval will be grouped together in the same file. The same convention will be used as above
except using the duplicate filenames rules described above. If an item does not share any interval
with any other Item then its name will be used in the filename.
For example:
If Items “I1”, “I2”, “I3”, “I4”, “I5”, “I6” are selected from Group1 of Data Set MyData Set and
Items “I1”, “I3” & “I6” share intervals and “I2” and “I5” share a different interval then the following
files will be generated.
Release 1.2
MyData Set1999011210Group1.csv
contains “I1”, “I3” & “I6”
MyData Set1999011210Group1_1.csv
contains “I2” & “I5”
Page 181
CHAPTER 11 – Data Logging
MyData Set1999011210I4.csv
OMRON
contains “I4”
On Change Items
All on change items will have their own filename generated regardless of any multiple selections
made, because it is not possible to determine any common time interval with these type of Items.
If a multiple selection of ‘On Interval’ and ‘On Change’ Items is made then the above conventions
still apply.
Generation of Text Files
Whereas CSV files only contain limited information e.g. Breaks, Date, Time, Milliseconds and
Value, Text files contains all the information stored on selected Items/Groups i.e. the expression,
label, deadband etc. The multiple selection rules apply as described in the previous paragraph, with
the exception that On Change items can be grouped together.
Data Logging
Overview
As well as the inbuilt datalogging features, it is also possible to log data directly to an existing
Database. This provides direct storage of data in third party format, allowing for easy analysis using
familiar tools, and there is no need for scripts to export data. However slower speed means logging
to a database may be unsuitable for tasks with large data throughput or high logging speed. Also,
unlike the standard Datalog files, there is no standalone viewer for instant viewing. The ADO
interface used to access Data Sources does not provide any mechanism for creating Databases or
Tables, therefore, it is not possible to automatically create a data source. Unpopulated data sources
for use in Database Logging, must first be created using the specific software for your choice of data
source e.g. "MS-Access".
To configure CX-Supervisor to log to a database:
♦
Create an ‘unpopulated’ data source or ‘template’ for use in Database logging.
♦
Create a Database connection in the Workspace Database editor to the database created above.
Add a recordset with a read/write lock, and fields with 'Field Property' configured as 'Add' so
records can be added.
♦
Create a Database Link in the Workspace Logging editor, by selecting 'Add Db Link...' from the
popup menu to show the Add Database Link dialog.
♦
Create Field Links for each field to log by selecting 'Add Db Field...' from the popup menu to
show the Add Field Link dialog.
Page 182
Release 1.2
OMRON
CHAPTER 11 – Data Logging
Add Database Link Dialog
The Add Database Link dialog show below is show when the 'Add Db Link...' menu option is
selected from the Data Log editor, and the identical Modify Database Link dialog when the 'Edit'
menu is selected.
Link Name
For convenience, a unique Database Link name is created automatically. This can be changed to give
a more meaningful description, if required.
Connection
Select the Database Connection to link to from the list showing configured Database connections.
Recordset
Select the Recordset to create a link to from the list showing Recordsets configured in the selected
Connection.
Sample Rate
Select whether field links defined within this Database Link are logged when their expression
changes or on a regular interval, for example every 30 seconds.
Start Logging on Application Startup
When unchecked, logging must be started and stopped using script commands. When checked, the
logging of all associated fields starts automatically when the application is started.
Release 1.2
Page 183
CHAPTER 11 – Data Logging
OMRON
Add Field Link Dialog
The Add Field Link dialog show below is show when the 'Add Field Link...' menu option is selected
from the Data Log editor, and the identical Modify Field Link dialog when the 'Edit' menu is
selected.
Name
For convenience, a unique Field Link name is created automatically. This can be changed to give a
more meaningful description, if required.
Field Link
Select the Field to link to from the list showing fields configured in the chosen Recordset.
Expression
Enter the point name or expression that will be logged. The Browse button allows easy point
selection.
Data Type
Set the type of the data to be stored. For a point, this is automatically set to the same as the point type
when selected using the Browse button. However, for an expression this must be specified, for
example, an expression $Second / 3 will create a Real value, but the required data may be just the
integer part, so the Data Type would be set to Integer.
Deadband
This allows the value of the expression to change within the percentage limit without being logged.
This is particularly useful when logging analogue values that are subject to noise. Each sample is
checked (when the value changes for ‘On Change’ sampling, or every log period for ‘On Interval’)
against the last logged value. While the value varies within the deadband, the values are ignored.
When the value exceeds the deadband limits the new value will be logged. This may dramatically
reduce file size, and ease analysis.
Page 184
Release 1.2
OMRON
CHAPTER 11 – Data Logging
Entering a value of 0%, i.e. no dead band, will cause every sample to be logged.
Trigger on change of value
This option is only used when the Sample Rate is set to 'On Change'. When unchecked, every time
the expression changes a new record is written. If a record consists of many fields that may be read
or calculated at different times, a new record is written every time any one field changes. However,
the desired action may be to change several fields, and then log the new values to a single record. To
achieve this action, the 'Trigger on change of value' should be checked for all fields within a record
that may be read or calculated at different times. Only when all checked fields have been changed is
the record logged. If however, while waiting for remaining fields to change before writing, a field is
changed for a second time, the record is written with all current field values including unchanged
fields, before the field value is changed for a second time.
Note:
Release 1.2
There is a risk when using fields with 'Trigger on change of value' checked that the
new value of a field may not actually change its value i.e. the new value happens to
be the same as the old value. Because the field has not changed, the record is not
written until the value is changed again. This can produce unexpected results as
fields with 'Trigger on change of value' unchecked are written with their current
values at the time of writing, not the value at the time of initial change. This may
also occur when a Deadband is used.
Page 185
OMRON
CHAPTER 12 – Databases
CHAPTER 12
Databases
Overview
CX-Supervisor Database facilities provide fast, transparent access to many different data sources, via
a database technology called ADO. Database design is not covered here, as it is a large subject
explained fully in any of the many books available. It is assumed that developers using these
database facilities have a working knowledge of databases. Comprehensive Database Script
Functions allow complete database access.
The data sources which can be accessed depends on the Data Providers installed, but may include:
♦
MS-Access
♦
MS-Excel
♦
Visual FoxPro
♦
dBase
♦
ODBC for Oracle
♦
Paradox
♦
SQL Server
♦
Text files (in TXT and CSV format)
Database Connection Editor
The Database connection editor in the Development Workspace, enables users to create Connections,
Recordsets, Field association, Parameter association and Schema objects in a familiar Tree View
(hierarchical) format, using the popup menu.
Release 1.2
Page 187
CHAPTER 12 – Databases
OMRON
This editor is unique in CX-Supervisor, in that actual database connections can be tested online in the
Development Environment. The ability to connect online also has the added benefit of providing
assistance in creating objects lower down in the hierarchy. This editor has been designed to enable a
large proportion of the database functionality, to be performed automatically (i.e. without the need for
Script functions), although a comprehensive set of Database Script functions are available.
Configuring a Connection
Connections to existing databases are added to the Workspace by using a right mouse-button context
sensitive menu option ‘Add Connection...’ which invokes the Add/Modify Database connection
dialog. They can be modified later by selecting the 'Edit...' option from the menu.
Add/Modify Database connection dialog
The Add Connection dialog show below is show when the 'Add Connection...' menu option is
selected from the Database connection editor, and the identical Modify Connection dialog when the
'Edit' menu is selected.
Page 188
Release 1.2
OMRON
CHAPTER 12 – Databases
Name
For convenience, a unique Connection name is created automatically. This can be changed to give a
more meaningful description of the connection, if required.
Data Source
Enter the database file to be used as a Data Source, or locate using the Browse button. The following
data source file types are supported:
♦
MS-Access Files (*.mdb)
♦
MS-Excel Files (*.xls)
♦
Text Files (*.txt, *.csv)
♦
FoxPro Files (*.dbf)
♦
Data Source Names (*.dsn)
A Data Source Name file stores information about a database connection in a file. See Creating a
Data Source Name file for more information.
Note:
Connecting to CSV or Text files is slightly different from an actual Database
connection. Only the ‘Directory’ that contains the required files should be supplied
as a Data Source - if a file is selected, the connection will fail. The actual file to be
used is specified later when configuring the Recordset. For example, if a collection
of text or csv files are contained in the directory C:\Text then a valid connection
‘Data Source’ is "C:\Text\".
Note:
Connections to CSV or Text files using the Provider installed with ADO version
2.0 are read only. Records can not be added or amended. To create a read/write
connection to a CSV or Text file see chapter 12, Creating a Read/Write connection
to CSV/Text file.
Note:
Connections to Excel files using the Provider installed with ADO version 2.0 are
read only. Records can not be added or amended. To create a read/write connection
to an Excel file see chapter 12, Creating a Read/Write connection to an Excel file.
Connect on Application Start-up
The checkbox ‘Connect on Application Start-up’ provides the option of automatically connecting to
the Database when the Runtime application is started.
Advanced
Shows the Connection String dialog, allowing the automatically generated connection string to be
manually edited.
Release 1.2
Page 189
CHAPTER 12 – Databases
OMRON
Testing Connections in the Development Environment
A connection to a Database can be made in the Development Environment by selecting the required
Connection in the Tree View and then selecting the right-menu option ‘Connect’. If a Connection
contains Recordsets that are set to auto open, these will also be opened by the ‘Connect’ option. If all
goes well and a valid connection is made, the Database Connection Icon will be adorned with a
‘lightning bolt’. If not, then this is probably due to an error in the ‘Connection String’.
Database Errors
A detailed description of what type of error occurred (supplied by the underlying Data Provider) can
be viewed, by ensuring that the right-menu option ‘Show Error’ is ‘checked’. Whenever an error is
generated by a Data Provider a description of the error and its source will be displayed in a Dialog.
The ‘Show Error’ option is specific to each Connection.
Example: The following error was generated by the ‘Jet Database Engine’ (due to a typo in the
Database name):
Database Connection String dialog
Connection to a Database is performed by means of a ‘Connection String’. Because different Data
Providers require different information to connect you to a data store, these strings can be quite
complex and cumbersome. For this reason CX-Supervisor will automatically create a valid
connection string for your selected data source (if it’s supported). This string can be viewed and
modified via the Connection String dialog shown below, when ‘Advanced’ is pressed on the
Add/Modify Database Connection dialog.
Page 190
Release 1.2
OMRON
CHAPTER 12 – Databases
If your data source is not supported, or you have your own drivers for a particular database, the
‘Connection String’ can be modified using this dialog (consult your database documentation for the
required connection string).
User Id and Passwords
If a connection to a database requires a user id or password, this can be supplied by means of the
connection string, which can be modified via the Advanced Dialog as follows:
If you make a mistake while editing the ‘connection string’, the original string can be restored by
selecting the ‘Build Connection String’ button. A new connection string will also be built
automatically each time a change of Data Source is made.
Example Connection Strings
Listed below are some example connections strings for the listed providers:
Release 1.2
Jet
"Provider=Microsoft.Jet.OLEDB.3.5.1; Data Source=c:\dbname.mdb"
SQL Server
"Provider=SQLOLEDB; Data Source=server_name; Initial Catalog=dbname;
User Id=user_id; Password=user_password"
Index Server
"Provider=MSIDXS; Data Source=catalog_name"
DSN
"DSN=data_source_name"
FILEDSN
"FILEDSN=filename.dsn"
MSDASQL
"Driver={Microsoft Excel Driver (*.xls)}; DBQ=c:\Database\Invdb.xls"
Page 191
CHAPTER 12 – Databases
OMRON
Data providers installed with ADO V2.0
Type
Jet 3.51
Provider Name
Microsoft.Jet.OLEDB.3.51
Description
For Microsoft Access databases
Directory Services
ADSDSOObject
For resource data stored, such as Active
Directory, this will become more
important when NT5.0 is available.
Index Server
MSIDXS
ODBC Drivers
MSDASQL
For existing ODBC Drivers, this ensures
that legacy data is not omitted.
Oracle
MSDAORA
Native Oracle driver simplifies access to
existing Oracle data stores.
SQL Server
SQLOLEDB
For Microsoft SQL Server.
Data Shape
MSDataShape
Persisted Records
MSPersist
For locally saved recordsets.
Simple Provider
MSDAOSP
For creating your own providers for
simple text data.
For Microsoft Index Server.
For hierarchical recordsets, this allows
the creation of master/detail type
recordsets, which allow drilling down into
detailed data.
The above is just the list of standard providers supplied by Microsoft. Other vendors are actively
creating their own.
Creating a Data Source Name file
A Data Source Name file (or DSN for short) stores information about a database connection in a file.
The file has the extension .DSN and by default is stored in the "$\Program Files\Common
Files\ODBC\Data Sources" directory. This type of file can be viewed with a suitable text editor e.g.
"Notepad". One advantage of using a DSN file over specifying the full path of the database is that
the DSN file remains unchanged while its contents can be re-configured to reflect any changes in
directory or database file name etc.
Creating a New DSN
♦
For Windows 95, 98, ME and NT: From your Windows ‘Control Panel’, select the ODBC Data
Sources icon. This will show the ODBC Data Source Administrator dialog box. For Windows
2000 and XP: From the ‘Programs’ folder, select ‘Administrative tools’ and ‘Data Sources
(ODBC) icon (note this is only available if the logged in user has administrative rights, and the
Taskbar properties “Display Administrative Tools’ option is checked). This will show the
ODBC Data Source Administrator dialog box.
♦
Click on the 'File DSN' tab. Any Data Source Names already defined will be listed.
Page 192
Release 1.2
OMRON
CHAPTER 12 – Databases
♦
Click on 'Add' to create a new Data Source Name file. This will invoke the Create New Data
Source dialog box with a list of available drivers (only drivers that are installed on your machine
will be shown).
♦
Choose the driver to access the data source and select ‘Next >’.
♦
You will then be prompted to name your Data Source. Type a suitable name and select ‘Next >’
♦
Verify the information shown and select 'Finish' to complete this part of the operation.
♦
Depending on the driver selected, you may be prompted for details of the database you wish to
connect to.
♦
A new DSN file will now exist which can be used by CX-Supervisor to Create a Connection.
Creating a Read/Write connection to an Excel file
Connections to Excel files using the Provider installed with ADO version 2.0 are read only hence
Records can not be added or amended. However, Excel files can be updated accessing the file via the
ODBC DSN driver. This is achieved by carrying out the following steps:
♦
Create a File DSN for the required Excel file with the following options (see Chapter 12,
Creating a Data Source Name file)
♦
Select the Microsoft Excel Driver (*.xls). If this option does not exist, you will need to install
the Microsoft ODBC driver for Excel from the Excel setup.
♦
Ensure that the "Read Only" check box is clear.
♦
Load the Excel spreadsheet and create a table to access the data by creating a Named Range as
follows:
♦
Highlight the row(s) and column(s) area where your data resides (including the header row).
♦
On the ‘Insert’ menu, point to ‘Name’, click ‘Define’ and enter a name for your range.
♦
Create a connection in the CX-Supervisor Workspace specifying the File DSN as its source.
♦
Add a Recordset to the connection and select the Named Range (which will appear in the list of
available tables, if the connection is live) as the Table name. Records in this table can now be
added or modified as with any other database table (Note: If records are added to this type of
table the Named Range will increase in size accordingly automatically).
The example below demonstrates a valid range selection named: "CustomerInvoice" (note the name
displayed just above column A):
Release 1.2
Page 193
CHAPTER 12 – Databases
OMRON
Note:
The first row of the range is assumed to contain the Column Headings.
Note:
When updating files the column headings cannot contain numbers or spaces, for
example "Column1" or "Invoice Total" is invalid. Also some words are reserved
and can not be used, for example a column heading of "Number" will cause an
error. These restrictions do not apply when only reading these files.
Note:
Make sure that all the cells in a column are of the same data type. The Excel
ODBC driver cannot correctly interpret which data type the column should be if a
column is not of the same type, or you have types mixed between "text" and
"general".
Note:
This type of querying and updating information in an Excel Spreadsheet does not
support multi-user concurrent access.
Creating a Read/Write connection to CSV/Text file
Connections to CSV or Text files using the Provider installed with ADO version 2.0, like Excel files,
are also read only hence Records can not be added or amended. However, CSV and Text files can be
updated by converting the data into an Excel spreadsheet and accessing the file via the ODBC DSN
driver. This is achieved by carrying out the steps as above using the CSV/Text file instead. Note the
Excel provider is still used, and a named range in Excel must still be created.
Page 194
Release 1.2
OMRON
CHAPTER 12 – Databases
Configuring Recordsets
The Recordset is the heart of the Database facility, it contains all of the columns and rows returned
from a specific action. The Recordset is used to navigate a collection of records, and update, add,
delete or modify records. Once a Connection has been added to the Workspace, the right menu
option ‘Add Recordset...’ will be enabled. Selecting this option will invoke the following dialog:
Name
A unique Recordset name will be automatically provided. This can be modified to provide a more
meaningful name if required.
Recordset Type
The Recordset can be 1 of 3 types:
Table Name
The Recordset is the name of an actual table in the Database.
Server Query
The Recordset is the results of a pre-defined Server Query stored in the database.
SQL Text
The Recordset is the results of an SQL query executed when the Recordset is
opened.
Release 1.2
Note:
It is more efficient to run a Server Query than an SQL query.
Note:
For Database connections all three of the above options are available, but for Text
or CSV connections only one option is available, namely ‘SQL Text’. For
convenience, a facility is provided for automatically building the required SQL
Text for this type of connection. This facility is invoked from the ‘Build SQL...’
button shown below:
Page 195
CHAPTER 12 – Databases
OMRON
This will bring up a dialog with a list of all valid files in the ‘Directory’ specified for the Connection.
After choosing a file and exiting from the ‘Build SQL’ dialog the required SQL Text is built. In the
above example, the file ‘Tables.txt’ was chosen, but this will be written as Tables#txt in the SQL
Text as most Providers will not accept the ‘.’ character, because it is used as a delimiter.
Source
The source field shows the Table name, Server Query or SQL text as selected above which the
Recordset is linked to.
Automatically open on connection
If this checkbox is ticked the Recordset will be automatically opened when the Connection is opened.
If this is unchecked, the Recordset must be open with a script command.
Lock
The lock option enables the Recordset to be opened in either read only or read/write modes, there are
two type of read/write locks as defined below:
Read Only
The default lock is read only i.e. data cannot be changed.
Pessimistic
Locks records when you start editing and releases the lock when Update() (or
Cancel()) is called, no need to worry about a conflict with other users, but can cause
records to be locked for long periods of time preventing other users from accessing
the same records.
Optimistic
Locked only when the Update() method is called, therefore changes can be made to
records without creating a lock, conflicts have to be catered for because someone else
might have changed the record between the time you started editing and the time you
called Update().
Page 196
Release 1.2
OMRON
CHAPTER 12 – Databases
Note:
If the Connection is open when a Recordset is added the Combo boxes for ‘Table
Name’ and ‘Server Query’ will be automatically populated with valid entries for
the selected Database. When the ‘Add Recordset...’ dialog is closed an attempt will
be made to open the newly configured Recordset.
Configuring Field Associations
Field associations provide a means of connecting CX-Supervisor Points with fields (i.e. columns of
data) in a Recordset, thus enabling data transfers to be made between Points and Records. By
creating a Field Association for each field in a record, data can easily be read from a record in the
database to its associated points, and written from the points to the current record in the database.
Once a Recordset has been added to a Connection in the Workspace, the right menu option ‘Add
Field...’ will be enabled. Selecting this option will invoke the following dialog:
Name
A unique Field name will be automatically provided. This can be modified to provide a more
meaningful name if required.
Point
The name of the point that will be used in data transfers. The Browse button may be used to select a
current point, or add a new one.
Field
The name of the Recordset field to be associated with the above point. If the Recordset is open, this
list will automatically show all available fields.
Release 1.2
Page 197
CHAPTER 12 – Databases
OMRON
Field Property
The type of information from the field to be transferred, the following options are available:
Value
default - the assigned value of the field
Name
the name of the field / column title
Type
the fields Data Type
Size
the maximum width of the field
Add
used to add new fields to a record
Note:
The Name, Type and Size properties are fixed for all entries of the column, whereas
the field value depends on the current position of the Recordset.
Note:
The ‘Add’ property is specifically designed to enable fields to be added together to
create new records. They are not involved in any read operations, as with the other
field property types. For this reason, the ‘Automatically read on open’ checkbox is
disabled when this type is applied. When creating configurations to add new
records you will need to create a ‘Add’ association for every field required to
‘create’ a valid record i.e. primary keys, non-null values etc. need to be catered for.
See DBAddNew() for more details.
Access field by index
When checked, a numeric index is used to identify a particular field instead of its name. This is
useful if you want to configure generic field associations.
Automatically read on open
When checked, the data is transferred from the Recordset field to the associated point, when the
Recordset is opened.
Field Paging
You can work with a single record at a time by associating points with the required fields, and
process the data one record at a time. However, if the point specified is an Array point the whole
array will be processed i.e. multiple fields will be read, written or added. This concept is called
Paging. Paging is supported by the Database script functions, enabling you to manipulate and
navigate the database a page at a time. CX-Supervisor determines the page size, by using the number
of elements in the Array point used in Field Associations, i.e. if an array point with 10 elements is
used then a page size of 10 will be used. In order for paging to work sensibly, you should ensure that
all array points used in multiple field associations for a particular Recordset are of the same size. If
arrays, of differing length are used, the smallest array size will be adopted as the page size.
Note:
Page 198
Paging only operates on Field Associations that have the Property Type ‘Value’
selected, this enables you to have Field Associations with a Property Type of
‘Name’ or ‘Add’ associated with single points in the same Recordset, without
effecting the page size determined by the array points.
Release 1.2
OMRON
CHAPTER 12 – Databases
Note:
Paging is designed to operate at the Recordset level (the concept of levels is
explained in the chapter on DB Script functions). If you perform a Read operation
on a recordset that has paging in force, then a ‘page’ of records will be read into all
the Field Associations connected to the Recordset. In contrast to performing a read
operation at the Field level which will override the page size and use the individual
fields length.
Configuring Parameter Associations
When a Recordset which is defined as a Server Query is opened, the query is executed, and the set of
records produced. The Server Query may be defined in the database as requiring parameters to be
passed which allow criteria to be passed to the query. Recordsets defined in CX-Supervisor as Server
Queries may have Parameter Associations added to the recordset. Recordsets defined as a Table
Name or SQL Text do not use parameters, hence any Parameter Associations are ignored.
Parameter associations provide a means of supplying values to parameters whenever a Server Query
is run. Each required parameter defined within the query is associated with a point or constant value.
At the time the Query is run, the current value of the point (or the constant value) is passed to the
query. Under the Development Environment the points default value is used.
Parameter Associations are added by right-clicking the Recordset and selecting 'Add Parameter...'
from the popup menu. The following dialog is shown:
Name
A unique Parameter Association name will be automatically provided. This can be modified to
provide a more meaningful name if required. By convention, this is made the same as the name of
the parameter defined within the database but this is not essential.
Index
The index is used to determine which parameter in the Query to associate the value with. The index
is automatically incremented for each parameter that is added to the Recordset.
Release 1.2
Page 199
CHAPTER 12 – Databases
OMRON
Data Type
The Data Type list will be populated with a selection of available data types. The correct data type
for the parameter being configured must be selected, otherwise the Recordset will fail to open.
Use point to hold parameter value
When unchecked, the constant Value specified is passed as the parameter to the query. When
checked, the current value of the point is passed as the parameter.
Point
The name of the point to be used. The Browse button may be used to select a current point, or add a
new one.
Value
The constant value to be used.
Configuring Schemas
Schemas enable information about a Database to be obtained from a Provider. There are a large
number of Schema Types available. The most useful feature of schemas is the ability to obtain Table
and Query names from the Database, in fact schemas are used by the Development Environment to
populate the Combo boxes when working with ‘live’ connections.
The information to be returned from the Provider is determined by specifying a Schema Type and a
Criteria. The Criteria argument is an array of values that can be used to limit the results of a schema
query. Each Schema type has a different set of Criteria that it supports.
A Schema is configured by selecting the desired Connection and choosing the right menu option
‘Add Schema...’ to invoke the following dialog:
Page 200
Release 1.2
OMRON
CHAPTER 12 – Databases
Name
A unique Schema name will be automatically provided. This can be modified to provide a more
meaningful name if required.
Point
The name of an array point which will hold the results of the schema request. The Browse button
may be used to select a current point, or add a new one.
Type
The Type list will be populated with a selection of available Schema Types.
Criteria
The Criteria list shows the available Criteria for the given Schema Type.
Filter
The Filter list is used with certain Schema types to reduce the information returned.
Read on Connection
If checked, the Schema results are automatically obtained when successful connection to the database
is achieved.
Preview
If the Connection is live, then the Preview button will be enabled on the dialog, which allows you to
view the results of the configured Schema.
The Schema ‘Type’, ‘Criteria’ and ‘Filter’ values can be modified at Runtime via the DBSchema()
function.
Database Schema Types
The Database Schema types supported in ADO are:
Schema Type values
Release 1.2
Criteria Values
Schema Asserts
CONSTRAINT_CATALOG
CONSTRAINT_SCHEMA
CONSTRAINT_NAME
Schema Catalogs
CATALOG_NAME
Schema Character Sets
CHARACTER_SET_CATALOG
CHARACTER_SET_SCHEMA
CHARACTER_SET_NAME
Page 201
CHAPTER 12 – Databases
Schema Type values
Page 202
OMRON
Criteria Values
Schema Check Constraints
CONSTRAINT_CATALOG
CONSTRAINT_SCHEMA
CONSTRAINT_NAME
Schema Collations
COLLATION_CATALOG
COLLATION_SCHEMA
COLLATION_NAME
Schema Column Domain Usage
DOMAIN_CATALOG
DOMAIN_SCHEMA
DOMAIN_NAME
COLUMN_NAME
Schema Column Privileges
TABLE_CATALOG
TABLE_SCHEMA
TABLE_NAME
COLUMN_NAME
GRANTOR
GRANTEE
Schema Columns
TABLE_CATALOG
TABLE_SCHEMA
TABLE_NAME
COLUMN_NAME
Schema Constraint Column Usage
TABLE_CATALOG
TABLE_SCHEMA
TABLE_NAME
COLUMN_NAME
Schema Constraint Table Usage
TABLE_CATALOG
TABLE_SCHEMA
TABLE_NAME
Schema Foreign Keys
PK_TABLE_CATALOG
PK_TABLE_SCHEMA
PK_TABLE_NAMEFK_TABLE_CATALOG
FK_TABLE_SCHEMA
FK_TABLE_NAME
Schema Indexes
TABLE_CATALOG
TABLE_SCHEMA
INDEX_NAME
TYPE
TABLE_NAME
Schema Key Column Usage
CONSTRAINT_CATALOG
CONSTRAINT_SCHEMA
CONSTRAINT_NAME
TABLE_CATALOG
TABLE_SCHEMA
TABLE_NAME
COLUMN_NAME
Release 1.2
OMRON
CHAPTER 12 – Databases
Schema Type values
Release 1.2
Criteria Values
Schema Primary Keys
PK_TABLE_CATALOG
PK_TABLE_SCHEMA
PK_TABLE_NAME
Schema Procedure Columns
PROCEDURE_CATALOG
PROCEDURE_SCHEMA
PROCEDURE_NAME
COLUMN_NAME
Schema Procedure Parameters
PROCEDURE_CATALOG
PROCEDURE_SCHEMA
PROCEDURE_NAME
PARAMTER_NAME
Schema Procedures
PROCEDURE_CATALOG
PROCEDURE_SCHEMA
PROCEDURE_NAME
PROCEDURE_TYPE
Schema Provider Specific
See Remarks
Schema Provider Types
DATA_TYPE
BEST_MATCH
Schema Referential Constraints
CONSTRAINT_CATALOG
CONSTRAINT_SCHEMA
CONSTRAINT_NAME
Schema Schemata
CATALOG_NAME
SCHEMA_NAME
SCHEMA_OWNER
Schema SQL Languages
<none>
Schema Table Constraints
CONSTRAINT_CATALOG
CONSTRAINT_SCHEMA
CONSTRAINT_NAME
TABLE_CATALOG
TABLE_SCHEMA
TABLE_NAME
CONSTRAINT_TYPE
Schema Table Privileges
TABLE_CATALOG
TABLE_SCHEMA
TABLE_NAME
GRANTOR
GRANTEE
Schema Tables
TABLE_CATALOG
TABLE_SCHEMA
TABLE_NAME
TABLE_TYPE
Page 203
CHAPTER 12 – Databases
Schema Type values
OMRON
Criteria Values
Schema Translations
TRANSLATION_CATALOG
TRANSLATION_SCHEMA
TRANSLATION_NAME
Schema Usage Privileges
OBJECT_CATALOG
OBJECT_SCHEMA
OBJECT_NAME
OBJECT_TYPE
GRANTOR
GRANTEE
Schema View Column Usage
VIEW_CATALOG
VIEW_SCHEMA
VIEW_NAME
Schema View Table Usage
VIEW_CATALOG
VIEW_SCHEMA
VIEW_NAME
Schema Views
TABLE_CATALOG
TABLE_SCHEMA
TABLE_NAME
Note:
The actual schemas are defined by the OLE DB specification and Providers are not
required to support all of the OLE DB standard schema queries. Specifically, only
‘Schema Tables’, ‘Schema Columns’, and ‘Schema Provider Types’ are required
by the OLE DB specification. However, the provider is not required to support the
Criteria constraints listed above for those schema queries.
Using Transactions
Modifications of data in the database i.e. adding, modifying and deleting records, can be grouped so
that all modifications take place at the same time. This group of modifications is called a
Transaction. A Transaction includes any modifications to data in a connection, regardless of the
Recordset. A transaction is started by calling DBExecute with the 'BeginTrans' command. From that
point, any request to add, modify or delete records are stored instead of being immediately processed.
The Transaction is completed either by calling DBExecute with the 'CommitTrans' command, which
processes all the stored requests in one go, or by calling DBExecute with the 'RollbackTrans'
command, which discards all the stored requests leaving the database as it was when the Transaction
started.
Nested Transactions
Transactions may be nested, that is a new transaction may be started before the preceding transaction
has been completed. In this case, any 'CommitTrans' or 'RollbackTrans' commands relate to the most
recently started transaction, and any further 'CommitTrans or 'RollbackTrans' commands relate to the
transaction begun before it.
Page 204
Release 1.2
OMRON
CHAPTER 12 – Databases
Note:
Care should be taken to ensure that each 'BeginTrans' is matched with a
'CommitTrans' or 'RollbackTrans' to ensure that your work is saved or discarded as
required. If there are any pending transactions when a connection is closed, the
user will be prompted to either commit or rollback these outstanding transactions.
A DBExecute command 'TransCount' is available which returns the number of
pending transactions.
Note:
Not all Providers support use of Transactions.
Saving Recordsets as XML
Using the DBExecute() 'Save' command any Recordset may be saved as an XML file, to be imported
in to another application. XML resembles and complements HTML. XML describes data, such as
city name, temperature and barometric pressure, and HTML defines tags that describe how the data
should be displayed, such as with a bulleted list or a table. XML, however, allows developers to
define an unlimited set of tags, bringing great flexibility to authors, who can decide which data to use
and determine its appropriate standard or custom tags.
Example: XML is used to describe an Employees phone list:
<EmployeeList>
<Entry>
<Employee>John Jones</Employee>
<Phone>555-1213</Phone>
<Type>Mobile</Type>
</Entry>
<Entry>
<Employee>Sally Mae</Employee>
<Phone>555-1217</Phone>
<Type>Business Fax</Type>
</Entry>
</EmployeeList>
You can use an application with a built in XML parser, such as Microsoft® Internet Explorer 5 to
view XML documents in the browser just as you would view HTML pages.
Datashaping
The ADO SHAPE command can be used to produce hierarchical recordsets i.e. where a value within
the current record is used to access another Recordset. For example, a record showing Customer
Details might contain a field for Customer ID. Every time the record position is changed, a child
Recordset showing Orders for that Customer ID could be recreated.
Release 1.2
Page 205
CHAPTER 12 – Databases
OMRON
Hierarchical recordsets present an alternative to using JOIN syntax when accessing parent-child data.
Hierarchical recordsets differ from a JOIN in that with a JOIN, both the parent table fields and child
table fields are represented in the same recordset. With a hierarchical recordset, the recordset
contains only fields from the parent table. In addition, the recordset contains an extra field that
represents the related child data, which you can assign to a second recordset variable and traverse.
Hierarchical recordsets are made available via the MSDataShape provider, which is implemented by
the client cursor engine.
A new clause, SHAPE, is provided to relate SELECT statements in a hierarchical fashion. The
syntax is summarized below:
SHAPE {parent-command} [[AS] name]
APPEND ({child-command} [[AS] name] RELATE parent-field TO childfield)
[,({child2-command} ...)]
Note:
By default, the child recordsets in the parent recordset will be called Chapter 1,
Chapter 2, etc., unless you use the optional [[AS] name] clause to name the child
recordset.
Note: You can nest the SHAPE command. The {parent-command} and/or {childcommand} can contain another SHAPE statement.
Note: The {parent-command} and {child-command} do not have to be SQL SELECT
statements. They can use whatever syntax is supported by data provider.
Note: A child recordset will be automatically opened/closed whenever its Parent recordset
is opened/closed. A child recordset is effectively a field of its parent recordset
therefore whenever a new record is selected in the parent a new child recordset will
be generated.
Creating a Datashape connection.
♦
Create DSN file specifying the required database as the Data Source
♦
Configure a Connection to the DSN file. In the connection string type
Provider=MSDataShape;
FILEDSN=<your file name>.dsn
♦
Configure a Recordset as SQL Text and enter the required shape command as the Source. (See
Datashape Source examples).
♦
After successfully adding a Datashape Recordset it is now possible to add a Child Recordset to
the existing Recordset by selecting the right menu option ‘Add Recordset’ which will now be
enabled. If the Connection is ‘Live’ a list of valid child recordset names will be entered in the
Source ComboBox
♦ Field associations can be added to Child recordsets in the normal manner.
Child recordsets can be accessed via Script command in a similar manner to normal recordsets
bResult = DBState( "DataShape.Customers.Orders.Details", "Open" )
Note:
Page 206
Child recordsets are not supported in the Database function dialog
Release 1.2
OMRON
CHAPTER 12 – Databases
Simple Relation Hierarchy example:
SHAPE {select * from customers}
APPEND ({select * from orders} AS rsOrders
RELATE customerid TO customerid)
The parent recordset contains all fields from the Customers table and a field called rsOrders.
rsOrders provides a reference to the child recordset, and contains all the fields from the Orders table.
The other examples use a similar notation.
Compound Relation Hierarchy example:
This sample illustrates a three-level hierarchy of customers, orders, and order details:
SHAPE {SELECT * from customers}
APPEND ((SHAPE {select * from orders}
APPEND ({select * from [order details]} AS rsDetails
RELATE orderid TO orderid)) AS rsOrders
RELATE customerid TO customerid)
In addition to the Simple Relation Hierarchy example, the Order ID is now used to create a recordset
containing the order details for the shown order.
Hierarchy with Aggregate example:
SHAPE (select * from orders}
APPEND ({select od.orderid, od.UnitPrice * od.quantity as
ExtendedPrice
from [order details] As od}
RELATE orderid TO orderid) As rsDetails,
SUM(ExtendedPrice) AS OrderTotal
This example creates a Recordset of all the orders and their details, and adds a field called
ExtendedPrice to store the total order value for each record, and sums all the ExtendedPrice values
which is stored in Order Total.
Group Hierarchy example:
SHAPE {select customers.customerid AS cust_id, orders.*
from customers inner join orders on customers.customerid =
orders.customerid} AS rsOrders
COMPUTE rsOrders BY cust_id
Release 1.2
Page 207
CHAPTER 12 – Databases
OMRON
Group Hierarchy with Aggregate example:
SHAPE
(SHAPE {select customers.*, orders.orderid, orders.orderdate from
customers inner join orders on customers.customerid =
orders.customerid}
APPEND ({select od.orderid,
od.unitprice * od.quantity as ExtendedPrice from [order details]
as od} AS rsDetails
RELATE orderid TO orderid),
SUM(rsDetails.ExtendedPrice) AS OrderTotal) AS rsOrders
COMPUTE rsOrders,
SUM(rsOrders.OrderTotal) AS CustTotal,
ANY(rsOrders.contactname) AS Contact
BY customerid
Note:
The inner SHAPE clause in this example is identical to the statement used in the
Hierarchy with Aggregate example.
Multiple Groupings example:
SHAPE
(SHAPE {select customers.*,
od.unitprice * od.quantity as ExtendedPrice from (customers
inner join orders
on customers.customerid = orders.customerid) inner join
[order details] as od on orders.orderid = od.orderid}
AS rsDetail
COMPUTE ANY(rsDetail.contactname) AS Contact,
ANY(rsDetail.region) AS Region,
SUM(rsDetail.ExtendedPrice) AS CustTotal,
rsDetail
BY customerid) AS rsCustSummary
COMPUTE rsCustSummary
BY
Region
Grand Total example:
SHAPE
(SHAPE {select customers.*,
od.unitprice * od.quantity as ExtendedPrice from (customers inner
join orders on customers.customerid = orders.customerid) inner
join
[order details] as od on orders.orderid = od.orderid}
Page 208
Release 1.2
OMRON
CHAPTER 12 – Databases
AS rsDetail
COMPUTE ANY(rsDetail.contactname) AS Contact,
SUM(rsDetail.ExtendedPrice) AS CustTotal,
rsDetail
BY customerid) AS rsCustSummary
COMPUTE SUM(rsCustSummary.CustTotal) As GrandTotal,
rsCustSummary
Note:
The missing BY clause in the outer summary. This defines the Grand Total
because the parent rowset contains a single record with the grand total and a pointer
to the child recordset.
Grouped Parent Related to Grouped Child example:
SHAPE
(SHAPE {select * from customers}
APPEND ((SHAPE {select orders.*, year(orderdate) as OrderYear,
month(orderdate) as OrderMonth from orders} AS rsOrders
COMPUTE rsOrders
BY customerid, OrderYear, OrderMonth)
RELATE customerid TO customerid) AS rsOrdByMonth )
AS rsCustomers
COMPUTE rsCustomers
BY region
Release 1.2
Page 209
CHAPTER 12 – Databases
Page 210
OMRON
Release 1.2
OMRON
CHAPTER 13 – Multilingual Features
Chapter 13
Multilingual Features
This chapter introduces CX-Supervisor’s Multilingual features to a new user, and explains how to
develop in, and create applications in languages other than the default English, for example:
• How a non-English designer can run the development tools in their native language,
even if they are creating an application in another language
•
How non-English applications can be developed
•
How applications can be developed where the end users with different nationalities can
switch between 2 languages (i.e. Bilingual) or more i.e. Multilingual
•
How applications can be developed for export, where the developers can work in their
native language and switch language before export, and maintenance engineers onsite
can switch back
Multilingual issues can be very complex, but like most areas CX-Supervisor provides this
functionality in an easy to use way, with a few simple dialogs.
The CX-Supervisor Multilingual features can easily be divided into two clear sections: Development
and Runtime. Users of each section has different needs and so these sections function completely
separately. For example, it is possible to develop an application in any language, but this does not
affect which language the user must use at runtime.
Note:
This distinction between development and runtime and their users is very important to
understand, and will help you understand the following sections.
Note:
CX-Supervisor is designed and tested for use with European versions of Microsoft Windows
and is not expected to operate with other versions like Russian, Japanese or Chinese etc.
Ensure your translated application can be correctly deployed before starting development.
Note:
The formatting of character tables used by CX-Supervisor for multilingual features is
Microsoft’s Double Byte Character Sets known as DBCS. This is not the same as Unicode
which is not yet supported on all operating systems. For this reason, to ensure text is
correctly displayed, ensure it is entered in DBCS format. Do not use a Unicode IME
(Windows NT and 2000) and do not paste from a Word document saved as Unicode format.
Development Features
For the benefit of the application developer the CX-Supervisor Development application may be run
in any major European language i.e. English, Spanish, Italian, German and French. This means all
menus, dialogs and error messages are shown in this language which should provide a more
comfortable and more efficient development experience.
Release 1.2
Page 211
CHAPTER 13 – Multilingual Features
OMRON
To choose between languages, at the beginning of the installation select the required language. Note
the installation runs in your selected language, and also the Development application resources are
installed in this language. If you ever need to change your language selection, simply uninstall CXSupervisor in the normal manner, and then reinstall, selecting the desired language.
Of course page names, on screen text, button captions etc are entered by the designer and all form
part of the runtime application. Translation of the runtime application is covered in the next section.
Note:
Remember the choice of development language is entirely separate to the language the end
user will use and has absolutely no impact on the runtime application.
Runtime Multilingual Features
The developer will be required to create the runtime application to run in at least 1 language. This is
often English but does not have to be. User defined text entered at development time, like button
captions, static text like “Value =”, graph titles etc can be exported to a text file for easy translation
into as many additional languages as required. At runtime the user can then change languages
dynamically i.e. without having to exit and restart the application. The translated system text and user
defined text is automatically loaded and displayed.
To support the diversity of end users, the Runtime features come translated in 13 languages
(including English) and can easily be extended by the developer. Applications supporting more than
one language can be very useful, for example for general use in countries with more than one national
language, or where a plant has a specific mix of personnel. This can also prove valuable when
developers and on-site maintenance engineers native language is different to the customers. The
system can be switched to a comfortable language during work, and easily switched back to the
customer’s requirement prior to hand over.
Note:
Page 212
Remember that the choice of runtime language is in no way connected to the language of the
installed Developer application.
Release 1.2
OMRON
CHAPTER 13 – Multilingual Features
Setting the Default language
The Runtime application first starts up in the preferred default language. Set this language during
development from the Language Settings dialog (select menu Project|Runtime Settings…|Language
Settings):
After setting, when the application is next run it will start in the selected language
Note:
In this context for this dialog only, “<Default>” means no language file will be loaded so the
default text compiled in the executable, i.e. English, will be used. This is the initial setting,
and can be useful if no Multilingual features are being used.
Changing language at Runtime
The user, if permitted, may change the language at runtime. The user may right-click the application
and select the “Language Settings…” option (see Chapter 6 Projects Menu Option Access Levels for
details of the right-click menu and setting access permissions).
Release 1.2
Page 213
CHAPTER 13 – Multilingual Features
Note:
OMRON
In this context, “<Default>” means the language selected as the default startup language
during development, in the above case Español (Spanish).
In addition, the developer may call the “SetLanguage” script function (see the CX-Supervisor Script
Language Reference Manual for details) for example behind a button to allow the user to
automatically switch languages.
User Defined text
While the Runtime system is shipped with full translations, any “user defined text” added by the
developer must be translated and these translations incorporated into the application. Examples of
user-defined text are:
•
Button captions, like “Open Page”
•
Text in Text objects, like “Value =”
•
Default values of Text Points
The system always loads user defined text from files with the file name exactly the same as the
language selection, and extension “.USL”. The file names for installed languages are: English, Czech,
Danish, Deutsch, Español, Finnish, French, Italiano, Nederlands (België), Norwegian, Português,
Slovenija and Swedish.
Note:
User defined text is specific to each application, and therefore is located in the application
project directory i.e. alongside the <project>.SCS file.
To get the user defined text translated and incorporated follow these steps:
1, 2, 3…
Page 214
1.
Develop your application completely. It is easier (and more effective) to
perform these steps just once. However if further development is required,
repeat these steps and use a development tool like WinGrep, Visual Sourcesafe
or other version control software which should easily show the changes that
have been made
Release 1.2
OMRON
CHAPTER 13 – Multilingual Features
2.
Export the user defined text by selecting menu Project|Create User Language
File. This will create a file in the project directory called “default.usl”
3.
Copy this file for as many translations as are required. Name each copy
<language>.usl using exactly the same text, especially with accents, as appears
in the Language Settings dialog. If the filename prefix is not exactly the same
the file will not be loaded. The format of these files is:
“development text”,”translated text”,optional object ID
The object ID (e.g. “Text_1”) is optional but can be supplied if specific text
requires different translations for different objects. For example “Run” in
English could be used as a verb on a button, and as static text for a run
number. In this case different translations can be supplied depending on the
object.
4.
Get these files translated. An editor like Notepad can be used to enter the
translated text in-between the quotes after the first comma.
5.
Copy the translated files back to the application directory. The runtime should
now automatically use these files.
Note:
Titles of pages titles cannot be translated. If necessary the page title can be hidden in the
Page Properties dialog, and custom title as static text added which does support automatic
translation.
Note:
User Aliases and System Aliases are exported for translation automatically however the
following System Aliases do not normally require any translation and can be left blank:
• “ExecuteJScript({”
• “ExecuteVBScript({”
• “)}”
Data Log Viewer
The Data Log Viewer is also supplied with translations for the 13 runtime languages. If launched
from the Runtime application, it automatically starts in the same language as the runtime application.
If it is started from the “Start” button, it always starts in English. The language can be selected from
the standard dialog from the menu “Options|Language Settings”.
Adding unsupported runtime languages
Although an impressive13 runtime languages are supported, you may require a language not listed. A
developer can easily add support for further languages:
1, 2, 3…
Release 1.2
1.
Copy the file “English.lng” in the installed application folder (“C:\Program
Files\Omron\CX-Supervisor”) and rename the copy with the language name,
e.g. “American.lng”.
Page 215
CHAPTER 13 – Multilingual Features
OMRON
2.
Translate the text between quotes. Note that formatting characters like %s or
%d indicate a position for inserted text or numbers so should be left in the
relevant place. Also the ‘&’ character used in menus signifies the keyboard
shortcut for the item so select an appropriate character in the translated
language
3.
The Runtime will now automatically show any new files with .LNG extension
in the “Language Settings” dialog.
4.
Repeat steps 1 and 2 above for the same file with the .LND extension. This
provides the translations for the Data Log Viewer.
5.
Create a new language file for the user defined text as described in the section
User Defined Text above.
To deploy this language to a new machine, just install CX-Supervisor as normal, and then copy the
.LNG and .LND file to the installed application folder (“C:\Program Files\Omron\CX-Supervisor”).
Note these are available for all applications run on this machine.
Page 216
Release 1.2
OMRON
CHAPTER 14 – Using CX-Supervisor as an OPC Client
Chapter 14
Using CX-Supervisor as an OPC Client
This chapter introduces OPC Server to a new user, and explains how to use CX-Supervisor as an
OPC Client.
What is OPC?
OPC stands for OLE for Process Control, and is a standard published by the OPC Foundation.
The basic aim of the OPC standard is to allow hardware vendors to produce software drivers (called
OPC Servers) and for software vendors to produce applications (called OPC Clients) which use a
standard method for data interchange. This allows software and hardware from different vendors to
be used together.
The latest version of the OPC standard is version 2. This replaces the earlier version 1 standard.
CX-Supervisor uses an OPC version 2 interface to connect to an OPC Server which is version 2
compliant. Note that the OPC version 1 interface has been superseded, and is not supported.
Users of CX-Supervisor may need some basic understanding of OPC. For more information on OPC,
see the OPC Foundation web site at www.opcfoundation.org.
For instructions on configuring your DCOM settings for connection to remote PCs, see Appendix A.
Using CX-Supervisor with Omron’s OPC Server
Omron supply a version 2 compliant server as part of the CX-Server OPC product.
Start the Omron OPC Server and configure as described in the CX-Server OPC manual and note that
the CX logo is displayed in the system tray.
1, 2, 3…
6.
Start CX-Supervisor and open your application.
7.
Open the Point Editor by selecting the Point Editor option from the Utilities menu
or by clicking the toolbar button.
8.
In the Point Editor dialog click the Add Point button in the toolbar to open the Add
Point dialog.
9.
In the Add Point dialog move to the I/O Type: options and select the Input, Output
or Input / Output option as appropriate. Note that the I/O Update Rate: and I/O
Attributes: options and displayed.
10. In the I/O Attributes: options select OPC/Other and click the Setup button. This
will open the Communications Control Attributes dialog.
11. In the Communications Control Attributes dialog enter the appropriate parameters
as follows:
Release 1.2
Page 217
CHAPTER 14 – Using CX-Supervisor as an OPC Client
OMRON
Communications Control Attributes
Server: This shows the name of the communications object to connect to the
server i.e. OMRONCXOPCCommunicationsControl. If you wish to use a
different object make your selection from the drop down list. To Add, Modify or
Delete an object click the Info button.
Selecting the Add option will open the Communications Control dialog. From the
list of control objects select the one to be added and click the OK button.
Clicking the OK button in the Communications Control dialog will open the
Communications Control Properties dialog from where the server details can be
added or updated. To edit these properties later select Modify from the Info menu.
Group: Select the Group containing the required item from the dropdown list. To
Add, Modify or Delete a Group click the Info button.
Items: The Items within the selected Group are listed. The Item Attributes dialog
can be used to add or edit the items. To Add, Modify or Delete an Item click the
Info button. Selecting the Add or Modify option will open the Items Attributes
window from where the item details can be added or updated.
Page 218
Release 1.2
OMRON
CHAPTER 14 – Using CX-Supervisor as an OPC Client
Array Size: Enter the number of array elements in the CX-Supervisor point that
this item should have. If not an array, enter 1.
1)
OPC COMMUNICATIONS CONTROL PROPERTIES
a) Server Tab The options in this window allow you to select the correct
name of the computer with the OPC Server and select the appropriate
server, i.e. Omron.OpenDataServer.1.
OPC Communication Control Settings
Name: – This is the name of the selected communications control. The
default
name
for
the
first
control
is
OMRONCXOPCCommunicationsControl. For each additional control
added the number increments by one.
Computer Name: – This shows the system name for the computer with
the OPC server. If the server is on the same computer as CX-Supervisor,
set to ‘(Local)’. If the OPC server is on a remote computer click the
Show All button and select the correct name from the list. If you can not
identify the PC in the list contact your system administrator.
Server Name: – This shows the names of the OPC Version 2 compliant
servers installed on the specified computer. Make your selection from the
drop down list. Clicking the Info button opens the Server Status
Information dialog for the selected server, check the information is
correct and click the OK button.
Project File
This is the name of the current Project file which stores the setup of the
Release 1.2
Page 219
CHAPTER 14 – Using CX-Supervisor as an OPC Client
OMRON
OPC items. If no name is shown or it is incorrect click the New or Open
button as appropriate.
Clicking the Open… button opens the Open Project dialog from where
you can navigate to the project file you wish to open. If you want to
create a new file click the New… button to open the Create Project
dialog. In the Create Project dialog navigate to the directory in which you
want to create your new file and enter your File Name. Select the
appropriate file type (Save as type – i.e. File Name.opc) and click the
Save button.
Note that a Project File name can not be entered from the keyboard, files
names can only be entered by using the New or Open buttons.
b)
Groups Tab The groups within the selected project file are listed. A
Group is made up of one or more items (data points) that share a common
update, rate enabling them to be controlled as a single entity. For
example you could create any number of groups each containing Items
that have the same update rate.
There is no limit to the number of groups you can have in a Project File
and each group can contain any number or type of Items (data points)
provided they have the same update rate.
Note that this dialog can not be opened until a valid project file exists in
which to create the groups.
Groups: – Use the Add, Edit and Delete buttons to show the Group
Attributes dialog and update the list of groups. For identification
purposes groups should be given logical names. The defaults are Group1,
Group2 etc.
i)
GROUP ATTRIBUTES
Name: – This is the name of the selected group. If you are editing an
existing group name or creating a new one the current or default
name is overwritten. The default name for new groups are Group1,
Group2 etc.
Page 220
Release 1.2
OMRON
CHAPTER 14 – Using CX-Supervisor as an OPC Client
Update Rate: – This is the rate at which the Items (data points) in
the group will be interrogated and new data entered if it is a readout,
or read from if it’s a control. Enter the rate as a numerical value and
select the units from the drop down list. The minimum value is
100msec; the maximum is 99999Sec i.e. over 27 hours.
Active On Startup: – Checking this option will make the Group
active when the OPC server is started. This means the items
contained within will be able to read and write data. The default is
checked.
c)
Items Tab The Items within the selected group are listed. Items are data
points of information stored in the OPC Server. The Item Attributes
dialog can be used to add or edit the items.
Note that this dialog can not be opened until at least one group is added.
i)
ITEM ATTRIBUTES
The Item Attributes dialog enables you to define the attributes of
each Item (data point) in the selected group.
Name: – This is the client name for an Item i.e. a point of data. If the
name is not known click browse button to open the Workspace
Browser dialog.
Item ID: – This is the OPC Servers name for the data. Consult the
documentation for the server to determine the correct format. For the
server included with CX-Server OPC, this should be the name of the
point in the CX-Server project (.CDM) file configured in the server.
Access Path: – This is the full path name for the data point. Consult
the documentation for the server to determine the correct format. For
the server included with CX-Server OPC this field is not used, and
may be left blank.
Data Type: – From the drop down menu select the format used to
Release 1.2
Page 221
CHAPTER 14 – Using CX-Supervisor as an OPC Client
OMRON
record the data point information.
Active On Startup: – Checking this option will ensure the Item is
active when the OPC server is started. The default is checked.
7.
Having checked that all the parameters are correct bring control back to the
Point Editor window by closing any attributes window that may be open.
The application can now be run by clicking on the Run Project button in the
toolbar. Note that the OPC Server logo is displayed momentarily as the server
starts. The CX-Supervisor Point will now be connected to the OPC Server
and can be used like all other CX-Supervisor points, i.e. to drive animations,
in alarm expressed, in recipes, for data logging etc.
Using with Third Party OPC Servers
The exact procedure for connecting CX-Supervisor to Third Party OPC Servers will depend on the
server being used. Consult your server documentation for full details. However, the following is a
basic overview:
1, 2, 3…
1.
Start and configure the OPC Server as appropriate.
2.
Start CX-Supervisor and follow steps 2 – 6 above as for connecting to Omron’s
OPC Server, but select the required OPC Server name or type the name
directly into the Server Name field.
Note: If the server is not shown in the drop down list, the server may not be
fully OPC version 2 compliant. Check the server documentation.
Create an OPC Group as described in ‘1-b-i’ Group Attributes’ above.
3.
4.
Page 222
Create an OPC Item as described in ‘1-c-i’ Item Attributes’ above. If the
server supports OPC item browsing facilities, click Browse to browse the OPC
Server to list the namespace groups and items to create the OPC Item ID.
Otherwise, type the OPC Item ID in the format specified in the server
documentation.
Release 1.2
OMRON
CHAPTER 15 – Connecting to a remote CX-Supervisor application
Chapter 15
Connecting to a remote CX-Supervisor application
This chapter explains how to connect multiple CX-Supervisor applications together to form a
distributed solution. Point data from one application can be 'shared' directly with other CXSupervisor applications across the PC network. Depending on the requirements, there are many
reasons and topographies for interconnecting CX-Supervisor applications.
Two Tier, Client - Server or Master - Slave
One application is configured as a Server application or Master. The Server is often the main station,
and is permanently switched on, and often used locally for HMI for example but could have no
graphical element, which is termed a Blind Server. It has direct access to the Devices or Device
network and is responsible for collecting the data from the devices.
Other applications may connect to the Server to read and even control values in the Server. These
applications are called Client applications or Slaves. Clients are often used remotely and therefore are
often configured 'display-only' applications, transferring the data from the Server using the corporate
PC network. The Clients do not talk directly to the devices, and often only connect when required.
Release 1.2
Page 223
CHAPTER 15 – Connecting to a remote CX-Supervisor application
OMRON
Peer to Peer
Several applications are written to share data with each other. Actually, an application is written as a Server to
connect directly to a device, but is also a Client using other Servers to connect to other devices through the
corporate network.
Distributed Server
Several applications are configured as Servers for direct connection, so the data for the system is 'distributed'
across several machines. One or more Client applications collect the data from the distributed servers. This
can be useful to help performance, by distributing the communication on the device connections, and server
processing. It can also provide different security for different clients and offers limited protect against
failures, as remaining servers still function.
Page 224
Release 1.2
OMRON
CHAPTER 15 – Connecting to a remote CX-Supervisor application
Redundant Server
Several applications are configured as Servers for direct connection to the same Devices or Device network.
The same data is collected by all Servers. One or more clients can collect the data from any single Server, and
in the event of a Server failure, can be written to switch to data from an alternative Server.
A distributed solution may be any of the above, or a combination of the ideas. Once your topography
is defined, the steps to connect each Client or Server are the same.
Creating a CX-Supervisor Server application
A Server application must collect device data, and allow clients to access it. It may also have other
elements like graphics, control or logging. To create your application:
♦ Create Device points for every data value required by the Server application and any
required by any client. See Chapter 3 - Points for more details.
♦ Configure DCOM on the server machine, to allow access from the client machines. See
Appendix A for further details.
♦ Add any other elements required by the Server application e.g. Graphics, Control, Logging,
Alarms etc.
Be sure to note the computer name of the server machine.
Note:
Release 1.2
A quick way to display the computer name is to right-click the 'Network
Neighbourhood' icon on the Windows Desktop and select 'Properties'.
Page 225
CHAPTER 15 – Connecting to a remote CX-Supervisor application
OMRON
Creating a CX-Supervisor Client application
The client must retrieve the data, and process it. To create your application:
♦ Add any elements required by the Client application e.g. Graphics, Control, Logging,
Alarms etc.
♦ Configure DCOM on the client machine, to allow access from the server machines. See
Appendix A for further details.
♦ Create points for every data value required by the Client application following these steps:
1, 2, 3…
1.
Start CX-Supervisor Development and open your application, or start a new
application.
2.
Open the Point Editor by selecting the Point Editor option from the Utilities
menu or by clicking the toolbar button.
3.
In the Point Editor dialog click the Add Point button in the toolbar to open the
Add Point dialog.
4.
In the Add Point dialog move to the I/O Type: options and select the Input,
Output or Input / Output option as appropriate. Note that the I/O Update Rate:
and I/O Attributes: options and displayed.
5.
In the I/O Attributes: options select OPC/Other and click the Setup button.
This will open the Communications Control Attributes dialog.
6.
In the Communications Control Attributes dialog enter the appropriate
parameters as follows:
Communications Control Attributes
Server: This shows the name of the communications object to connect to the
server i.e. OMRONCXSupervisorCommunicationsControl. If you wish to use a
different object make your selection from the drop down list. To Add, Modify
or Delete an object click the Info button.
Selecting the Add option will open the Communications Control dialog. From
the list of control objects select 'OMRON CX-Supervisor Communications
Page 226
Release 1.2
OMRON
CHAPTER 15 – Connecting to a remote CX-Supervisor application
Control' and click the OK button.
Clicking the OK button in the Communications Controls dialog will open the
Communications Control Properties dialog from where the server details can be
added or updated. Click 'Show All' and select the computer name of the server
machine from the list. To edit these properties later select Modify… from the
Info menu.
Group: Select the Group containing the required item from the dropdown list.
To Add, Modify or Delete a Group click the Info button.
Items: The Items within the selected Group are listed. The Item Attributes
dialog can be used to add or edit the items. To Add, Modify or Delete an Item
click the Info button. Selecting the Add or Modify option will open the Items
Attributes window from where the item details can be added or updated.
Array Size: Enter the number of array elements in the CX-Supervisor point that
this item should have. If not an array, enter 1.
7.
Having checked that all the parameters are correct return to the Point Editor
window by closing any attributes window that may be open.
The application can now be run by clicking on the Run Project button in the
toolbar. The CX-Supervisor Point will now be connected to Remote CXSupervisor application and can be used like all other CX-Supervisor points, i.e.
to drive animations, in alarm expressed, in recipes, for data logging etc.
Release 1.2
Page 227
CHAPTER 15 – Connecting to a remote CX-Supervisor application
Page 228
OMRON
Release 1.2
OMRON
CHAPTER 16 – Connecting to Omron Industrial Components
CHAPTER 16
Connecting to Omron Industrial Components
This chapter details connecting CX-Supervisor to Omron's Industrial Components, like Temperature
Controllers, Digital Panel Meters and Timer/Counters. Any process value or parameter from these
devices can be monitored or written. See the device documentation for available parameters and their
description.
This is achieved in CX-Supervisor by creating a point and linking it to the required parameter.
Adding a point linked to a parameter
1, 2, 3…
1.
Start CX-Supervisor Development and open your project.
2.
Open the Point Editor by selecting the Point Editor option from the Utilities
menu or by clicking the toolbar button.
3.
In the Point Editor dialog click the Add Point button in the toolbar to open the
Add Point dialog.
4.
In the Add Point dialog move to the I/O Type: options and select the Input,
Output or Input / Output option as appropriate. Note that the I/O Update Rate:
and I/O Attributes: options and displayed.
5.
In the I/O Attributes: options select OPC/Other and click the Setup button.
This will open the Communications Control Attributes dialog.
6.
In the Communications Control Attributes dialog enter the appropriate
parameters as follows:
Communications Control Attributes
Server: This shows the name of the communications object to connect to the
server i.e. OMRONCXICCommunicationsControl. If you wish to use a
Release 1.2
Page 229
CHAPTER 16 – Connecting to Omron Industrial Components
OMRON
different object make your selection from the drop down list. To Add, Modify
or Delete an object click the Info button.
Selecting the Add option will open the Communications Control dialog. From
the list of control objects select the one to be added and click the OK button.
Clicking the OK button in the Communications Controls dialog will open the
Communications Control Properties dialog from where the details can be added
or updated. To edit these properties later select Modify from the Info menu.
CX IC COMMUNICATIONS CONTROL PROPERTIES
Page 230
Release 1.2
OMRON
CHAPTER 16 – Connecting to Omron Industrial Components
Name: – This is the name of the selected communications control. The default
name for the first control is OMRONCXICCommunicationsControl. For each
additional control added the number increments by one.
Project File: - This is the name of the current Project file that stores the setup
of the items. If no name is shown or it is incorrect click the Info button and
select Create… or Open… as appropriate.
Clicking the Open… button opens the Open Project dialog from where you can
navigate to the project file you wish to open. If you want to create a new file
click the Create… option to open the Create Project dialog. In the Create
Project dialog navigate to the directory in which you want to create your new
file and enter your File Name. Select the appropriate file type (Save as type –
i.e. File Name.msc) and click the Save button.
Note that a Project File name can not be entered from the keyboard, files names
can only be entered by using the Create or Open options.
Device: Select the Device containing the required item from the dropdown list.
To Add, Modify or Delete a Device click the Info button.
Items: The Items within the selected Device are listed. The Item Attributes
dialog can be used to add or edit the items. To Add, Modify or Delete an Item
click the Info button. Selecting the Add or Modify option will open the Items
Attributes window from where the item details can be added or updated.
Array Size: Enter the number of array elements in the CX-Supervisor point
that this item should have. If not an array, enter 1.
7.
Having checked that all the parameters are correct bring return to the Point
Editor window by closing any attributes window that may be open.
The CX-Supervisor Point will now be connected to Device parameter and can
be used like all other CX-Supervisor points, i.e. to drive animations, in alarm
expressions, in recipes, for data logging etc. The application can now be run by
clicking on the Run Project button in the toolbar.
Release 1.2
Page 231
CHAPTER 16 – Connecting to Omron Industrial Components
Page 232
OMRON
Release 1.2
OMRON
APPENDIX A – Configuring a PC for remote connection
APPENDIX A
Configuring a PC for remote connection
The OPC interface and CX-Supervisor Communications Control use a Microsoft technology called
DCOM. This allows the Clients and Servers to be seamlessly ‘Distributed’ over a PC network. The
Server should be running on the PC with direct connection to the Device or Device network.
However, the Client, or indeed multiple Clients, can be run on different networked PCs and will
automatically read and write data over the PC network. To do this, the PC running the Server must
be correctly configured. If necessary refer to your OPC server documentation. For full details of
DCOM configuration and security issues see your Microsoft documentation. The following is a
quick guide:
Note:
Although DCOM connections can be achieved using Windows 95, 98 and ME they
are more difficult to configure, and offer less functionality. For best results always
use Windows NT or Windows 2000.
Configuring a Client PC running Windows NT or 2000
1, 2, 3…
1.
Start DCOMCNFG.EXE e.g. by selecting RUN from the start button. The
default location is C:\WINDOWS\SYSTEM.
2.
View the Default Properties tab. Ensure that the Enable Distributed COM
on this computer is checked.
Configuring a Client PC running Windows XP
1, 2, 3…
1.
Start Component Services e.g. by running DCOMCNFG.EXE by selecting
RUN from the start button. The default location is C:\WINDOWS\SYSTEM.
2.
Select Component Services followed by Computers.
3.
Right click My Computer and select Properties
4.
View the Default Properties tab. Ensure that the Enable Distributed COM
on this computer is checked.
Configuring a Client PC running Windows 95, 98 or Me
1, 2, 3…
1.
2.
Release 1.2
Ensure File and Printer sharing is enabled by selecting Network from the
Control Panel. Add a service and click either “File and print sharing for
Microsoft Networks” or “File and print sharing for Netware Networks” as
appropriate.
Start DCOMCNFG.EXE e.g. by selecting RUN from the Start button. The
default location is C:\WINDOWS\SYSTEM.
Page 233
APPENDIX A – Configuring a PC for remote connection
3.
OMRON
View the Default Properties tab. Ensure that the Enable Distributed COM
on this computer is checked.
A CX-Supervisor Client running on Windows 95, 98 or ME also requires the Microsoft Remote
Registry network service to be installed with the operating system and correctly configured on both
the server and client machine. To check: start the Control Panel and view the Network settings. In
the list of network components, look for Microsoft Remote Registry. If it does not exist, follow
these steps to add it.
1, 2, 3…
1.
4.
In the Network settings, ensure User-level access control is selected on the
Access Control tab.
From the Configuration tab, click Add to add a Network component. Choose
Service from the type list and click Add.
Click Have Disk… and browse your Windows CD. Select the path
(\Admin\Nettods\remotReg) for Win95 or
(\Tools\ResKit\NetAdmin\RemotReg) for Win98 and select regsrv.inf.
Follow the screen prompts to complete installation and reboot if necessary.
5.
6.
7.
On the server machine, select Passwords from the Control Panel.
Ensure the Enable remote administration of this server option is checked
Add all required user ids to the Administrators list by clicking Add…
2.
3.
Note: Windows ME no longer includes the Microsoft Remote Registry network service on
the product CD but this can still be installed and used from any Windows 95 or
Windows 98 CD ROM using the above steps.
Configuring a Server PC running Windows NT or 2000
1, 2, 3…
1.
Start DCOMCNFG.EXE e.g. by selecting RUN from the Start button. The
default location is C:\WINDOWS\SYSTEM.
2.
View the Default Properties tab. Ensure that the Enable Distributed COM on
this computer is checked.
From the Default Properties tab, configure the Default Authentication Level
to Connect and the Default Impersonation Level to Identify. Setup the access
permissions by either:
a) On the Default Security tab, adding the user to the Access, Launch and
Configuration lists by clicking the Edit Default… button in each case.
b) From the Applications tab, configure the properties for required
applications e.g. SCS, OpenDataServer and OpcEnum. On the Security
tab, add the required users to each of the Custom Permissions.
3.
Page 234
Release 1.2
OMRON
APPENDIX A – Configuring a PC for remote connection
Configuring a Server PC running Windows XP
1, 2, 3…
1.
Start Component Services e.g. by running DCOMCNFG.EXE by selecting
RUN from the start button. The default location is C:\WINDOWS\SYSTEM.
2.
Select Component Services followed by Computers.
3.
Right click My Computer and select Properties
5.
View the Default Properties tab. Ensure that the Enable Distributed COM
on this computer is checked.
From the Default Properties tab, configure the Default Authentication Level
to Connect and the Default Impersonation Level to Identify. Setup the access
permissions by either:
a) On the Default COM Security tab, adding the user to the Access,
Launch and Configuration lists by clicking the Edit Default… button in
each case.
b) From the My Computer item in Component Services, select DCOM
Config and configure the properties for required applications e.g. SCS,
OpenDataServer and OpcEnum. On the Security tab, add the required
users to each of the Custom Permissions.
4.
Configuring a Server PC running Windows 95, 98 or Me
1, 2, 3…
1.
2.
3.
4.
5.
Release 1.2
Ensure File and Printer sharing is enabled by selecting Network from the
Control Panel. Add a service and click either “File and print sharing for
Microsoft Networks” or “File and print sharing for Netware Networks” as
appropriate.
Start DCOMCNFG.EXE e.g. by selecting RUN from the Start button. The
default location is C:\WINDOWS\SYSTEM.
View the Default Properties tab. Ensure that the Enable Distributed COM on
this computer is checked.
View the Default Security tab and check the Enable remote connection check
box.
From the Default Properties tab, configure the Default Authentication Level
to Connect and the Default Impersonation Level to Identify. Setup the access
permissions by either:
a) On the Default Security tab, adding the user to the Access list by clicking
the Edit Default… button in each case.
b) From the Applications tab, configure the properties for OPC Server and
OPC ServerList Class. On the Security tab, add the required users to each
of the Custom Permissions.
Page 235
APPENDIX A – Configuring a PC for remote connection
OMRON
Third party servers and clients running on Windows 95, 98 or ME may require the Microsoft
Remote Registry network service to be installed with the operating system and correctly configured
on both the server and client machine. To check: start the Control Panel and view the Network
settings. In the list of network components, look for Microsoft Remote Registry. If it does not exist,
follow these steps to add it.
1, 2, 3…
1.
4.
In the Network settings, ensure User-level access control is selected on the
Access Control tab.
From the Configuration tab, click Add to add a Network component. Choose
Service from the type list and click Add.
Click Have Disk… and browse your Windows CD. Select the path
(\Admin\Nettods\remotReg) for Win95 or
(\Tools\ResKit\NetAdmin\RemotReg) for Win98 and select regsrv.inf.
Follow screen prompts to complete installation and reboot if necessary.
5.
On the server machine, select Passwords from the Control Panel.
6.
Ensure the Enable remote administration of this server option is checked.
7.
Add all required user ids to the Administrators list by clicking Add….
2.
3.
Note: Windows ME no longer includes the Microsoft Remote Registry network service on
the product CD but this can still be installed and used from any Windows 95 or
Windows 98 CD ROM using the above steps.
Page 236
Release 1.2
OMRON
APPENDIX B – Obsolete Features
APPENDIX B
Obsolete Features
This appendix provides a summary of features that are obsolete and have been removed from the
standard documentation. Details are included here to assist maintaining old projects still using these
features. These features should not be used in development of new solutions as it is likely support for
the following features may and will be removed from the next or future releases.
Windows 95
This product is no longer tested under Windows 95, so Omron cannot guarantee correct operation. It
is recommended to upgrade to Windows NT or an NT successor.
System Points
The following System Points are obsolete and are no longer updated. Scripts and expressions will
currently still compile, but their value at Runtime will always be 0.
$GDIResources
Integer
0-100
Percentage of GDI resources free.
$SystemResources
Integer
0-100
Percentage of system resources free.
$UserResources
Integer
0-100
Percentage of user resources free.
DDE
Overview
CX-Supervisor supports Dynamic Data Exchange (DDE), which is a method of communication
between Windows programs. DDE uses messages to exchange data between applications and a
protocol to synchronise the passing of data. DDE applications fall into four categories client, server,
client/server and monitor. A client application requests data or services from a server application. A
server application responds to a client applications requests for data or services. Monitor applications
can intercept DDE messages but cannot act on them, they are therefore useful for debugging
purposes. CX-Supervisor is a client/server application, which is both a client application and a server
application, thus requesting and providing information.
All CX-Supervisor DDE data transfers are carried out on points and are asynchronous transfers.
There are two types of DDE points that can be created, namely ‘DDE Client Points’ and ‘DDE Server
Points’.
With ‘DDE Client Points’ all data transfers or conversations are initiated by CX-Supervisor either
sending data to or requesting data from external DDE Server Application(s). For example, a CXSupervisor point could be linked to update a cell on a Microsoft Excel worksheet.
Release 1.2
Page 237
APPENDIX B – Obsolete Features
OMRON
With ‘DDE Server Points’ all data transfers are initiated by external DDE Client Application(s) either
requesting or sending point values. For example, a value could be entered into a cell in Microsoft
Excel which would update a CX-Supervisor point.
DDE Client Points
A DDE client point sends data to or requests data from an external server application. This chapter
explains how to create points that make use of the CX-Supervisor DDE Client capabilities. In order
for data to be transferred between a point and a server application the point must uniquely identify the
application and the data that is to be used in the transfer. DDE applications use a three-tiered
identification system to distinguish themselves from other DDE applications. An application name is
at the top of the hierarchy, the application name refers to a server application e.g. “EXCEL”. A topic
name further defines a server application e.g. for Microsoft Excel the topic would define the
worksheet to be used e.g. “SHEET1.XLS”, a server can support one or more topics. Finally each
topic can have one or more item names, which uniquely identifies a data item within a topic, i.e.
“R1C1” or a cell name reference identifies a single cell within a Microsoft Excel worksheet.
Example
A DDE Client point named “DDE1” that connects to Microsoft Excel, worksheet – “Sheet1.xls” and
cell “R1C1”, is created.
1, 2, 3…
Page 238
1.
Select the Add Point button from the Point Editor toolbar. The Add Point
dialog is displayed.
2.
Enter “DDE1” in the Point Name: field.
3.
Set the I/O Attributes setting to DDE and click on the Setup pushbutton.
The DDE attributes dialog is displayed.
4.
Enter “Excel” in the Server Name: field. This is the name of the external
DDE server application.
Release 1.2
OMRON
APPENDIX B – Obsolete Features
Note:
5.
Enter “Sheet1.xls” in the Topic Name: field. This is the required topic, in
this case it is a Microsoft Excel worksheet named ‘Sheet1.xls’. It is
possible to specify a specific topic: for instance, in Microsoft Excel, to
specify a sheet within a book a colon is used to delimit the information, e.g.
‘Book1:sheet3.xls’.
6.
Enter “R1C1” in the Item Name: field. This refers to the item name.
7.
Enter “1” in the Array Size: field.
8.
Click the OK pushbutton to accept the settings in both the DDE Attributes
dialog and the Add Point dialog.
It is not necessary to give ‘DDE Client Points’ DDE access via the Advanced dialog
- this field is only used in the creation of ‘DDE Server Points’. If the DDE Access
Read/Write setting is set ‘ON’, this point’s value would then be ‘exposed’ to change
by external DDE server application(s) which may not always be desirable.
This process is repeated for any further DDE data transfers that are required.
DDE Server Points
A DDE server point receives data from or receives a request for data from an external Client
application. This chapter explains how to create “DDE Server Points”, these points are exposed to
DDE Client applications either for “Read/Only” or “Read/Write” access. In order for a point to take
part in a conversation with a DDE Client, it must be given ‘DDE Access’. The following dialog
demonstrates how to give a Real memory point, DDE Read/Write access:
A DDE Server point is created as follows:
1, 2, 3…
Release 1.2
1.
Select the Add Point button from the Point Editor toolbar. The Add Point
dialog is displayed.
2.
Enter a meaningful name for the DDE Server point in the Point Name:
field.
3.
Click on the Advanced pushbutton. The Advanced Point Settings dialog is
displayed.
Page 239
APPENDIX B – Obsolete Features
OMRON
4.
Ensure the DDE Access Read/Write setting is set to ‘ON.
5.
Click the OK pushbutton to accept the settings in both the Advanced Point
Settings dialog and the Add Point dialog.
Note:
The DDE Access group’s Read/Write box in the Advanced Point Settings dialog is
checked, this is the only action required to expose “DDESVR3” to a DDE Client
application for read/write access.
Note:
Any CX-Supervisor point can be given DDE Access, even DDE Client points.
DDE Array Points
CX-Supervisor supports arrays in DDE, for both ‘Client’ and ‘Server’ transactions. DDE Client data
transfers are initiated by CX-Supervisor, either sending or requesting data from external DDE
Applications (such as Microsoft Excel). DDE Server data transfers are initiated by external DDE
Applications either sending or requesting data to or from CX-Supervisor.
Refer to the CX-Supervisor Script Language Reference Manual for further details.
DDE Client Array Points
This chapter explains how to create DDE Client Array points. This is similar to the way normal DDE
Client points are created, except extra information is required to specify the range of the array and
also whether it is to be stored as a row or column in the Server application.
1, 2, 3…
1.
Select the Add Point button from the Point Editor toolbar. The Add Point
dialog is displayed.
2.
Enter a meaningful name in the Point Name: field.
3.
Set the I/O Attributes setting to DDE and click on the Setup pushbutton.
The DDE attributes dialog is displayed.
4.
Enter an application in the Server Name: field.
5.
Enter a topic in the Topic Name: field.
6.
Enter the item in the Item Name: field. It is also necessary to specify how
the array is to be transferred. For instance, in Microsoft Excel, this is either
as a ‘[row]’ or ‘[column]’, the default is as a row which can be omitted.
The following are valid array item names: “R1C1:R3C1[col]”,
“first:last[c]”, “R5C2:R5C5”, “r1c1:r3c1[column]”.
7.
Enter the number of elements in the array in the Array Size: field. This
must match with the specified range in the Item Name field
In the CX-Supervisor Runtime environment, the above DDE Client array transactions are initiated by
means of script in the same way as single DDE Client points. The CX-Supervisor script below gives
examples of the facilities available with DDE Client array points:
Page 240
Release 1.2
OMRON
APPENDIX B – Obsolete Features
1) Example CX-Supervisor Script demonstrating client array points
chan = DDEInitiate(“Excel”, “Book1.xls”)
IF chan > 0 THEN
‘Establish data transfers between point ‘DDEArray’ and Excel
‘the initial values of DDEArray is sent to Excel
DDEOpenLinks(chan)
‘The array is initialised with the value 5 and sent to Excel in
one
operation.
InitArray(DDEArray, 5)
‘The contents of ‘MemoryArray’ are copied into ‘DDEArray’ and the
‘array are sent to Excel in one operation.
MemoryArray[0] = 100
MemoryArray[1] = 34
MemoryArray[2] = 89 * 6
CopyArray(MemoryArray, DDEArray)
‘Sets element 2 of the array to 6 and sends the whole array to
Excel
‘Note: Use ‘On Request’ option and ‘OutputPoint’ to send the array
‘after ‘setting several elements of a large array.
DDEArray[2] = 6
ENDIF
DDE Script Functions
The existing DDE Script functions DDEPoke() and DDERequest() can be used with any array points
as the following example CX-Supervisor Scripts show:
1) Example CX-Supervisor Script demonstrating DDEPoke() with arrays
chan = DDEInitiate(“Excel”, “Book1:Sheet2”)
IF chan > 0 THEN
‘Send element 1 of ‘RealArray’ to Excel
DDEPoke(chan, "R16C1", RealArray[1])
‘Send IntegerArray to Excel as a column (note: range and column
must
‘be ‘specified)
DDEPoke(chan, "R1C1:R3C1[column]", IntegerArray)
‘Send TextArray to Excel as a row (default only range required)
DDEPoke(chan, "R1C2:R1C4", TextArray)
ENDIF
Release 1.2
Page 241
APPENDIX B – Obsolete Features
OMRON
2) Example CX-Supervisor Script demonstrating DDERequest() with arrays
chan = DDEInitiate(“Excel”, “Book1:Sheet3”)
IF chan > 0 THEN
‘Request a row of cells from Excel and copy into ‘Array1
Array1 = DDERequest(chan, "R1C1:R1C3")
‘Request a column of cells from Excel and copy into Array2, using
‘the return ‘flag
Array2 = DDERequest(chan, "R1C2:R3C2", bReturnFlag)
‘Request a cell value from Excel and copy into element 2 of
‘Array1’
Array1[2] = DDERequest(chan, "R3C2")
ENDIF
Note:
All the above points must have DDE Read/Write access set.
DDE Server Array Points
The value of an array point named ‘ddearray’ in a CX-Supervisor project called ‘ddetest.srt’ can be
read from a Microsoft Excel worksheet by entering the following formula format into a cell.
=<Server>|<Topic>!<item>.<index>
Example
=SCS|Point!ddearray.3
‘access ddearray[3] using ‘Point’ topic
=SCS|ddetest.srt|ddearray.0
topic
‘access ddearray[0] using ‘Project’
or
Note:
Microsoft Excel accepts the square brackets ‘[ ]’ used in CX-Supervisor to
reference an array index in a formula; use ‘.’ instead.
Note:
The index must always be specified if an individual array element is required.
Note:
CX-Supervisor supports ‘Hot’ DDE links, if Microsoft Excel has the link option
automatic set, then the value in Microsoft Excel are updated whenever
ddearray[index] changes.
The above example is the simplest way to access/read single elements of an array from Microsoft
Excel, to read/write whole arrays, it is necessary to use macros (Microsoft Excel Visual Basic
scripts).
The example scripts that follow have all been created using Microsoft Excel and are working
examples. They contain the minimum amount of information required to demonstrate the particular
facility being described; i.e. they do not contain any error-checking code.
Page 242
Release 1.2
OMRON
APPENDIX B – Obsolete Features
Sending Arrays to CX-Supervisor via DDEPoke()
In order to write to an CX-Supervisor array point using the DDEPoke() function, it must first be
given DDE Read/Write access, via the Advanced Point Settings dialog when adding or modifying the
point. The following script shows how to send arrays of values from Microsoft Excel to CXSupervisor via DDEPoke().
1) Example sending array values from Microsoft Excel to CX-Supervisor
Sub SendArrayValues()
Dim chan As Integer
chan = DDEInitiate(“SCS”, “Point”)
If chan <> 0 Then
‘Send a row of data to an array point named “Array1”
DDEPoke chan, “Array1”, Range(Cells(1,1), Cells(1,3))
‘Send a column of data to an array point named “Array2”
DDEPoke chan, “Array2”, Range(Cells(2,1), Cells(4,1))
‘Send individual array element values to “Array3”
‘The ‘[ ]’ or ‘.’ format can be used to delimit the array index
DDEPoke chan, “Array3[0]”, Cells(1,1)
DDEPoke chan, “Array3.1”, Cells(1,2)
DDEPoke chan, “Array3[2]”, Cells(1,3)
End If
End Sub
Requesting Arrays from CX-Supervisor via DDERequest()
Requesting arrays from CX-Supervisor and storing them in Microsoft Excel is a little more
complicated than sending, in that both CX-Supervisor and Microsoft Excel need to know if the array
is to be stored in rows or columns. CX-Supervisor is informed of the row/col requirement by
specifying either ‘row’ or ‘column’ after the array points name. The default is ‘row’ if nothing is
specified. The following are all valid examples of specifying names for “Array1” in a
DDERequest():
“Array1”, “Array1:Row”, Array1:r”
‘Valid ways to specify a row
“Array1:Column”, “Array1:col”, Array1:C” ‘Valid ways to specify a
‘column
Microsoft Excel is informed of the row/col requirement by specifying a Range of cells in either row
or column format. Both the Microsoft Excel and CX-Supervisor specifications must match in order
for the call to be successful. It is not necessary to specify rows or columns if a single element of an
array is required.
Note:
DDE Requests are one-shot request, i.e. they are not part of a ‘Hot’ link.
1) Example requesting CX-Supervisor array values from Microsoft Excel
Sub RequestingArrayValues()
Dim chan As Integer
Release 1.2
Page 243
APPENDIX B – Obsolete Features
OMRON
chan = DDEInitiate(“SCS”, “Point”)
If chan <> 0 Then
‘Request “Array1” from CX-Supervisor and store in a row starting
at R1C1
Range(Cells(1,1), Cells(1,3)) = DDERequest(chan, “Array1”)
‘Request “Array2” from CX-Supervisor and store in a column
starting at R2C1
Range(Cells(2,1), Cells(4,1)) = DDERequest(chan, “Array2:col”)
‘Request elements [2] and [3] from “Array2” and store in R3C1 &
‘R3C2
‘The ‘[ ]’ or ‘.’ format can be used to delimit the array index
Cells(3,1) = DDERequest(chan, “Array2[2]”)
Cells(3,2) = DDERequest(chan, “Array2.3”)
End If
End Sub
OLE Automation
OLE Automation provides a mechanism whereby one application can control another. In order to
access a CX-Supervisor points value via OLE Automation, it must be given either OLE Read or OLE
Write access. This can be achieved by checking the appropriate box in the Advanced Point Settings
dialog when the point is created or modified.
Note:
All CX-Supervisor System points are given OLE2 read access by default.
CX-Supervisor exposes the following Runtime functions via OLE2 Automation:
♦ SetValue(stringPointName,Value). Enables any point with OLE Read/Write access to be
modified (value may be Boolean, integer, long or string).
♦
GetValue(stringPointName,&Value). Enables any point with OLE Read access to be monitored
(value may be Boolean, integer, long or string).
♦
QueryCount(). Returns the total number of points in the CX-Supervisor database.
♦
QueryId(stringPointName), Returns the WORD id of a given point name. The id is an integer in
the range between 1 and the total number of points in the CX-Supervisor database.
♦
QueryOLE(wordID). Returns the Read/Write access rights of a point as an integer. 0 represents
no access type; 1 represents Read Only; 2 represents Read/Write; 3 represents an invalid access
type.
♦
QueryType(wordID). Returns the points data type as an integer from a given id. 0 represents a
void datatype; 1 represents a digital datatype; 2 represents an integer datatype; 3 represents a real
datatype; 4 represents a text datatype; 5 represents an invalid datatype.
QueryName(wordID). Returns the points name string from a given identity. CX-Supervisor provides OLE
Automation helper routines and code examples in the OLE2AUTO subdirectory. Refer to the file
OLE2AUTO.WRI in that subdirectory for more information.
Page 244
Release 1.2
OMRON
APPENDIX B – Obsolete Features
OLE Overview
The Microsoft Windows operating environment allows the transfer and sharing of information
between applications by using a technique known as Object Linking & Embedding, or OLE
(pronounced olé). Embedding allows drawings, sounds or almost any objects to be created within an
application, and then inserted (embedded or linked) within another file or document. The embedded
object can then be edited (or activated) by merely double clicking on it. Linking allows an object to
be shared by several documents by forging links between the destination documents and the source
object, e.g. a company logo may appear in several word processor documents by linking to a graphics
object rather than embedding.
Embedding and Linking Objects within the CX-Supervisor application can either be achieved by
using the Object Packager, or by embedding or linking objects directly within a page.
Note:
Packages may only be embedded or linked into CX-Supervisor pages if they are
created using OLE-compliant applications. This applies to objects either directly
linked or embedded within CX-Supervisor, and those inserted using the Object
Packager.
Object Packager
The Object Packager is a Windows application which enables objects to be “wrapped” for insertion
into documents. It can be used to either create a link to a file held on disk or to embed an object into
a page. Once embedded or linked, the object can be moved and positioned in a similar way to any
other object created within CX-Supervisor.
To use the Object Packager, select Package from the list of objects displayed in the Insert Object
dialog shown later in this chapter. An example of a typical Object Packager window is as follows:
For the remainder of this chapter only the direct insertion of objects using the CX-Supervisor built-in
functions are detailed. For further details of using the Object Packager refer to the Windows User
Guide, or the Object Packager On-line Help.
Whether using the Windows Object Packager or embedding or linking objects directly, proceed as
follows:
Release 1.2
Page 245
APPENDIX B – Obsolete Features
1, 2, 3…
OMRON
1.
Click on the page in which the object is to be inserted.
2.
Click the Insert OLE Object button.
displayed:
The Insert Object dialog is
Creating an Object From New
To create an object from new, proceed as follows:
1, 2, 3…
1.
Scroll through the list of object types presented in the list box until the
desired type is highlighted.
2.
Click the OK pushbutton to insert the object into the current page and
display it as it would look from within the application in which the object
was created.
To display the object as an icon, click on the Display As Icon setting.
The icon displayed is the first one which is stored in the icon resource table for
the application which created the object (in the case of the example shown, a
Paintbrush icon). If another icon is required, clicking the Change Icon
pushbutton displays the following dialog:
Page 246
Release 1.2
OMRON
APPENDIX B – Obsolete Features
1, 2, 3…
1.
Select either the current or default icon by clicking either the Current: or
Default: setting; and click the OK pushbutton to return to the Insert Object
dialog. Should a different label be required to display beneath the inserted
icon, delete the contents of the Label: field and type in a new label (the
default label offered is the filename of the file containing the inserted
object).
2.
Type the full path of the target application or DLL ending with the
application or DLL name, into the From File: field. To locate an existing
file name or a different path, click the Browse pushbutton to display the
Browse dialog.
An example of the Browse dialog is shown as follows:
Release 1.2
Page 247
APPENDIX B – Obsolete Features
OMRON
Both programs (extension .EXE) or Dynamic Link Libraries (extension .DLL) are listed in the Files
of Type field.
The Browse dialog functions identically to the File Open dialog described in chapter 6, Projects
except the file list offered shows icons as opposed to pages.
1, 2, 3…
1.
On return to the Change Icon dialog, select the required icon from those
presented.
2.
Change the icon’s label (if required).
3.
Click the Open pushbutton to return to the Insert Object dialog.
4.
On return to the Insert Object dialog click the OK pushbutton to return to
the current page and embed the selected object into it at the current insertion
point.
Creating an Object From a File
Creating an object from a file allows linking or embedding of objects created at sometime in the past.
As before, select Insert New Object from the Edit menu, and the Insert Object dialog is displayed.
Click the Create From File: setting and the dialog changes to a format similar to that of the
following:
Type the full path of the file containing the object to be inserted, ending with the full file name, into
the Create from File: field. To locate an existing file name or a different path, click the Browse
pushbutton to display the Browse dialog.
A Browse dialog similar to that used for changing an object’s icon is displayed, the difference being
that the List Files of Type field has a single entry of All Files (extension .*).
1, 2, 3…
Page 248
1.
Use the Look in: field to navigate to the appropriate location.
Release 1.2
OMRON
APPENDIX B – Obsolete Features
2.
Select the file from the list offered and click the Open pushbutton to return
to the Insert Object dialog.
3.
On return to the Insert Object dialog click the OK pushbutton to return to
the current page and embed the selected object into it at the current
insertion point.
To display the object as an icon, follow the procedure detailed in the previous chapter and click the
OK pushbutton to return to the current page and embed the selected object, in icon form, into it at the
current insertion point.
It is often more appropriate to link to an object rather than embedding it in the current page. By
linking to an object rather than embedding it CX-Supervisor always has access to the most up-to-date
copy of the object every time the page containing it is opened.
Placing a check mark in the Link field forges a link between the page and the file containing the
object.
All other activities are carried out in an identical manner to those explained previously.
The following illustrates a Microsoft Excel Chart object which has been inserted in a page:
Release 1.2
Page 249
APPENDIX B – Obsolete Features
OMRON
Activating an Object
To activate an embedded or linked object, merely double click using the left mouse button on the
object’s graphical representation on the page (either a true representation of the object or an icon). If
the object is a document or image, Windows activates the application that created the object and
places it, ready to be edited.
In the following example, the bitmap image when activated launches the Format Chart Area
application to allow editing:
When editing is complete, select Update and Exit from the application’s File menu to return to CXSupervisor.
Note:
The Update and Exit command varies from application to application.
If the object is an animation or sound file, when activated it is played through until it ends, at which
point control is returned to CX-Supervisor.
Note:
Page 250
If the application which created the object no longer be available, CX-Supervisor
reports an error.
Release 1.2
OMRON
APPENDIX B – Obsolete Features
Converting a Package Object
Certain types of object may be converted from one form to another. To initiate conversion:
1, 2, 3…
Note:
Release 1.2
1.
Select the object on the page.
2.
Activate the Edit menu and select Package Object (displayed as the last
item on the Edit menu).
3.
Select Convert from the sub-menu displayed.
The menu item name varies from application to application but always references
the inserted object.
Page 251
GLOSSARY OF TERMS – CX-Supervisor User Manual
OMRON
GLOSSARY OF TERMS
ADO
AND
Application
Arguments
ASCII
Bitmap
Boolean type
COM
Communications Driver
Page 252
ADO stands for Active Data Objects and is data access technology which
uses OLE-DB to access data sources in a uniform way e.g. MS-Access
databases, MS-Excel spreadsheets and Comma Separated Variable files.
A logic operator used to interrogate Boolean type points. AND returns
‘TRUE’ if all arguments are ‘TRUE’. An example of AND is that if a is a
statement and b is a statement, AND returns ‘TRUE’ if both a and b are
‘TRUE’. If one or both statements return ‘FALSE’ then AND returns
‘FALSE’.
A software program that accomplishes a specific task. Examples of
applications are CX-Supervisor, CX-Server and Microsoft Excel. CXSupervisor and its development environment allows the creation and
testing of new applications through a Graphical User Interface (GUI).
Words, phrases, or numbers that can be entered on the same line as a
command or statement to expand or modify the command or statement
within the CX-Supervisor script language. The command acts on the
argument. In essence the command is a verb, and the argument is the
object of the verb. An example of an argument in CX-Supervisor is
“DDETerminate(channel)” where DDETerminate is a command
within the script language, and channel is the argument upon which the
command will act.
An old standard, defining a set of characters. Officially using only 7 bits
allows definitions for only 127 characters, and does not include any
accented characters.
The representation of an image stored in a computer’s memory. Each
picture element (pixel) is represented by bits stored in the memory. In CXSupervisor a bitmap image can be installed as a single object.
A type of point where the value of the point can be one of two states.
Essentially the two states are ‘0’ and ‘1’, but these states can be assigned a
meaningful designation. Examples are:
State
Example
Example
Example
Example
0
‘OFF’
‘FALSE’
‘OUT’
‘CLOSED’
1
‘ON’
‘TRUE’
‘IN’
‘OPEN’
See also: AND, NOT and OR.
COM is a Microsoft technology that allows components used to interact.
The relevant communications management system for OMRON PLCs in
conjunction with Microsoft Windows, providing facilities for other
SYSMAC software to maintain PLC device and address information and to
communicate with OMRON PLCs and their supported network types.
Release 1.2
OMRON
GLOSSARY OF TERMS - CX-Supervisor User Manual
Constant
Within CX-Supervisor, a constant is a point within the script language that
takes only one specific value.
In CX-Supervisor, a control object is applied in the development
environment and can be a pushbutton, a toggle button, a slider, a trend
graph, a rotational gauge or a linear gauge. Essentially a control object can
be a complex graphic object consisting of a number of primitive graphic
objects, which provides user interaction.
An advanced communications management system for OMRON PLCs
providing facilities for software to maintain PLC device and address
information and to communicate with OMRON PLCs and their supported
network types. CX-Server supports CS-Series PLCs.
A Database connection (or Connection for short) contains the details used
to access a data source. This can either be via Data Source Name (DSN),
filename or directory.
A Database Connection Level is a string which determines what level in
the database tree hierarchy is to be operated on. Some examples are listed
below:
"Northwind"
Connectionlevel
"CSV.Result"
Recordset level
"Northwind.Order Details.OrderID"
Field level
"Invoice.Data Types"
Schema level
A Database recordset (or Recordset for short) is a set of records. This
could either be an actual Table in the database, or a table that has been
generated as a consequence of running a Query.
A Database Schema (or Schema for short) obtains database schema
information from a Provider.
A Database Server Query (or Server Query for short) is a query that is
stored in the actual Database. They are pre-defined and added by the
database designer which means they are 'fixed' for the duration of a project.
Server Queries may have pre-defined 'Parameters', which allow criteria to
be passed to the query at runtime e.g. values to filter, allowing one query to
be used to produce different results. Each pre-defined parameter must
have a Parameter Association defined. Because these queries are stored in
a compiled and tested form they are more efficient and therefore
preferential to running a SQL Query.
A Database SQL Query (or SQL Query for short) is interpreted
dynamically at runtime. The SQL Text can be modified at runtime,
enabling different Queries to be run for varying situations however, the
SQL Text has to be compiled on the fly every time it is executed and
consequently is less efficient than a Server Query.
Control Object
CX-Server
Database connection
Database Connection Level
Database Recordset
Database Schema
Database Server Query
Database SQL Query
Release 1.2
Page 253
GLOSSARY OF TERMS – CX-Supervisor User Manual
DBCS
DCOM
DDE
Development Environment
DLL
Download
Executable
Expressions
Field association
Page 254
OMRON
DBCS stands for Double Byte Character Set and is a Microsoft extension
of ASCII which uses 2 bytes (16 bits) to define character codes. With this
larger range it can include accented characters, extended ASCII characters,
Nordic characters and symbols.
DCOM is a distributed version of COM that allows components on
different PCs to interact over a network.
Dynamic Data Exchange. A channel through which correctly prepared
programs can actively exchange data and controls other applications within
Microsoft Windows. CX-Supervisor, through the use of its script
language, allows extensive use of DDE functionality.
See also Item, Server, server application and Topic.
SCADA applications are created and tested using the development
environment within CX-Supervisor.
On completion, the finished
application can be delivered as a final customer application to be run by
the run-time environment.
Dynamic Link Library. A program file that although cannot be run standalone as an executable, can be utilised by one or more applications or
programs as a common service. DLL files have a *.DLL extension.
DLL’s comprise a number of stand-alone functions. In CX-Supervisor, a
DLL containing icons can be accessed to represent the display part of an
OLE object. One such DLL, ‘MORICONS.DLL’, is provided in the
standard Microsoft Windows installation.
A recipe is downloaded during runtime. This process involves identifying
the appropriate recipe and executing the validation code, if any exists. The
download is complete when each ingredient has set its point to the target
value.
A file that contains programs or commands of an application that can be
executed by a user or another application. Executable files have a *.EXE
file extension. CX-Supervisor provides two executable files, one for the
development environment (CXSUPERVISORDEV.EXE), and one for the
run-time environment (SCS.EXE).
In the CX-Supervisor script language, expressions are a construct for
computing a value from one or more operands. For instance, in the
example “lift = height + rate”, the expression is “height +
rate” where the result yielded from the expression is used for the value
of “lift”.
Outside of the script language, expressions consisting of operators and
operands can be used to control objects, through actions.
A field association enables a link to be made between a CX-Supervisor
Point and a particular field (i.e. column) within a recordset.
Release 1.2
OMRON
Graphic Object
GUI
I/O type
Icon
Ingredient
Integer type
Item
JScript
JVM
Microsoft Excel
Microsoft Windows
Microsoft Word for Windows
Nesting
Network
Release 1.2
GLOSSARY OF TERMS - CX-Supervisor User Manual
In CX-Supervisor, a graphic object is created in the development
environment, and can be a line, an arc, a polygon (including a square and
rectangle), a round rectangle, an ellipse (including a circle), or a polyline.
A complex object can exist as a combination of two or more graphic
objects.
Graphical User Interface. Part of a program that interacts with the user and
takes full advantage of the graphics displays of computers. A GUI
employs pull-down menus and dialog boxes for ease of use. Like all
Microsoft Windows based applications, CX-Supervisor has a GUI.
Input/Output type. An attribute of a point that defines the origin and
destination of the data for that point. The data for a point can originate (be
input from) and is destined (is output to) to the internal computer memory
or PLC.
Pictorial representations of computer resources and functions. The CXSupervisor development environment and run-time environment are run
from icons.
Each recipe consists of at least one ingredient. Each ingredient must be
related to an existing point.
A type of point where the value of the point can only be a whole positive
or negative number.
Within the CX-Supervisor script language, Item is a generic term for a
point, OPC item or Temperature Controller item.
A Java style scripting language supported by Microsoft’s Windows
Scripting Host.
Java Virtual Machine.
A spreadsheet application.
A windowing environment that is noted for its GUI, and for features such
as multiple typefaces, desk accessories (such as a clock, calculator,
calendar and notepad), and the capability of moving text and graphics from
one application to another via a clipboard.
CX-Supervisor will run only under Microsoft Windows. DDE functions
communicating with other applications supported by CX-Supervisor use
Microsoft Windows as a basis.
A word processing application.
To incorporate one or more IF THEN ELSE/ELSEIF ENDIF statements
inside a structure of the same kind.
1. Part of the PLC configuration, based on the device type. The number
of Networks available is dependant on the device type.
Page 255
GLOSSARY OF TERMS – CX-Supervisor User Manual
Non-Volatile
NOT
Object
OLE-DB
Operand
Operator
OR
Pages
Parameter Association
Pixel
Page 256
OMRON
2. A number of computers linked together with a central processing point
known as a Server which is accessible to all computers. Networks
affect CX-Supervisor in that further Network associated options are
available if the computer is Network connected.
A point that is designated as ‘non-volatile’ is a point whose value is saved
on disk and automatically reloaded when CX-Supervisor resumes
execution.
A logic operator used to interrogate Boolean type points which produces
the Boolean inverse of the supplied argument. An example of NOT is that
if a is a statement and is ‘FALSE’, then NOT returns ‘TRUE’. If a is a
statement and is ‘TRUE’, then NOT returns ‘FALSE’.
In CX-Supervisor, an object can be text, graphics, a control, a bitmap, or
ActiveX object as created in the development environment. A complex
object can exist as a combination of two or more objects of any of the
above types. Specifically, graphical objects can be categorised as a line, an
arc, a polygon (including a square and rectangle), a round rectangle, an
ellipse (including a circle), or a polyline. A control is essentially a
complex graphic object and is specifically either a pushbutton, a toggle
button, a slider, a trend graph, a rotational gauge or a linear gauge.
OLE-DB is the underlying database technology, on which ADO relies.
OLE-BD is designed to be the successor to ODBC.
The term used for constants or point variables.
A symbol used as a function, with infix syntax if it has two arguments (e.g.
“+”) or prefix syntax if it has only one argument (e.g. NOT). The CXSupervisor script language uses operators for built-in functions such as
arithmetic and logic.
A logic operator used to interrogate Boolean type points. OR returns
‘TRUE’ if any of the supplied arguments are ‘TRUE’. An example of OR
is that if a is a statement and b is a statement, OR will return ‘TRUE’ if
either a and b are ‘TRUE’. If both statements return ‘FALSE’ then OR
will return ‘FALSE’.
The combination and manipulation of pages containing objects within
projects forms the basis of CX-Supervisor. More than one page can exist
for each project. The pages in a project provide the visual aspect of CXSupervisor corresponding to a display with the objects contained in each
page providing a graphical representation of the system being monitored.
A Parameter Association enables values, either constant or stored in a
point, to be passed to a Server Query.
A single displayable point on the screen from which a displayed image is
constructed. The screen resolution of the computer’s Visual Display Unit
(VDU) is defined by the number of pixels across and the number of pixels
down (e.g. 1024 x 768).
Release 1.2
OMRON
PLC
Point variable
Point
Project
Real type
Recipe
Run-Time Environment
SCADA
Server
Server Application
Statement
String
Release 1.2
GLOSSARY OF TERMS - CX-Supervisor User Manual
See also SVGA mode and VGA mode.
Programmable Logic Controller.
A point within the CX-Supervisor script language that stores a value or
string assigned to that point.
A point is used to hold a value of a predefined type - Boolean, Integer,
Text, etc. The contents of a point may be controlled by an object or I/O
mechanism such as PLC communication. The contents of a point may
control the action or appearance of an object, or be used for output via an
I/O mechanism.
See also Boolean type, Integer type, point variable, Real type and Text
type.
A CX-Supervisor application will consist of one or a number of pages
linked together. The pages may contain passive or active graphics, text or
animations, and may be grouped together logically to form a project. A
project may consist of many pages, or simply a single page. Projects may
be built and tested within the CX-Supervisor development environment,
and run stand-alone under the CX-Supervisor run-time environment.
Only one project at a time may be open for editing within the CXSupervisor development environment.
A type of point where the value of the point can be any number, including
those containing a decimal point.
A recipe is a set of pre-defined steps used to perform a particular task. A
CX-Supervisor project may contain zero or more number of recipes.
Recipes are defined in the development environment and executed, or
downloaded, in the run-time environment.
SCADA applications are run using the run-time environment of CXSupervisor, following creation of the application in the CX-Supervisor
development environment.
Supervisory Control and Data Acquisition.
A Server is the central processing point of a Network that is accessible to
all computers. Networks affect CX-Supervisor in that further associated
options are available if the computer Network is connected.
An application that can be used to view or interact with, whilst currently
within CX-Supervisor.
Within the CX-Supervisor script language, a statement is a command
understood by the run-time environment. Statements are constructed of
commands and arguments, which when combined, help to formulate a
finished application to be used in the run-time environment.
The contents of a Text type point that can only contain literal alphanumeric
characters. A string starts following an opening quotation mark, and ends
before a closing question mark; in the example “name = "spot"”, the
point “name” holds the string spot.
Page 257
GLOSSARY OF TERMS – CX-Supervisor User Manual
SVGA mode
CX-Supervisor
Target Value
Taskbar
Text Object
Text Type
Unicode
Validation Code
VBScript
VGA mode
Windows Desktop
Windows Scripting Host
Wizard
Page 258
OMRON
A mode of video display that provides 800 × 600 pixel resolution (or
higher) with 16 or more colours and is supported on Super Video Graphics
Adapter systems.
A SCADA software application which creates and maintains graphical user
interfaces and communicates with PLCs and other I/O mechanisms.
An ingredient must specify a target value for its related point. This is the
value to which the point will be set in runtime when the recipe is
downloaded.
An integral part of Microsoft Windows which allows Microsoft Windows
based applications to be started. CX-Supervisor is run from the Taskbar.
In CX-Supervisor, a text object is a string on a page. Attributes such as
typeface, point size, embolden, italicise, underline, left justify, flush right,
and centre can be applied to enhance its presentation.
A type of point that holds a string.
A Multi-Byte Character Set, which not only includes European Characters
like DBCS, but can also include global support including for Japanese,
Chinese and Cyrillic fonts. However, Unicode is not supported on all
Windows platforms.
Recipe validation code is CX-Supervisor script language which is used to
check point values before downloading a recipe.
A Visual Basic style scripting language supported by Microsoft’s
Windows Scripting Host.
A mode of video display that provides 640 × 480 pixel resolution with 16
colours and is supported on Video Graphics Adapter systems.
An integral part of Microsoft Windows which allows Microsoft Windows
based applications to be started from icons and for all applications to be
organised. CX-Supervisor can be run from Windows Desktop.
A scripting engine supplied by Microsoft to run VBScript or JScript. See
http://msdn.microsoft.com/scripting
Wizards are dialogs used by the CX-Supervisor development environment
to take the user through complex operations in a simplified step-by-step
process.
Release 1.2
OMRON
Release 1.2
GLOSSARY OF TERMS - CX-Supervisor User Manual
Page 259
INDEX – CX-Supervisor User Manual
OMRON
INDEX
A
About CX-Supervisor · 258
About the Point Editor · 23
About the Project Editor – Project Editor · 99
Access
Alarm Editor · 98, 109, 111, 119, 120
Animation Editor · 122
Graphics Editor · 1
Graphics Library · 103
Point Editor · 23
Project Editor · 98
Project Workspace · 98
Recipe Editor · 98, 156
Accessing PLC Connection in Runtime – Device
Configuration · 79
Activating Graphics Library - Graphics Library · 103
ActiveX Objects
Editing · 68
Events · 70
Inserting · 67
Methods · 70
Overview · 67
Properties · 70
Adding Pages to a Project – Project Editor · 99
Advanced Point Settings– Creating Points: · 32
Alarm Editor · 109–11
About · 109–11
Access · 98, 109, 111, 119, 120
Delete alarm · 117
Modify alarm · 33–34, 33–34
Viewing contents · 111
Alarm Objects - Control Objects · 46
Alarm Points - Point Import: · 40
Alarms
Alarm Editor · See Alarm Editor
Current status · 119
Customise settings · 85
Deadband · 114
Editor, Alarms · See Alarm Editor
Groups · 111, 113
History · 119
Information · 112
Page 260
Print alarms · See also Page, Preview page; Page,
Print page; Page, Setup page for printing
Rate of change · 114
Simple · 114
Workspace · 98
Alias Definitions · 96
Alignment - Manipulating objects · 64
Alignment Toolbox - Manipulating objects · 64
Amending a Page · 14
Amending a Project · 74
Amending an Existing Point · 33
Animation Editor
About · 121
Access · 122
Alias definitions · 96, 130
Analogue Colour Change · 126, 141–42
Analogue Display Value · 126, 146–47
Analogue Edit Point Value · 126, 149–51
Analogue User Input · 126, 149–51
Blink · 126, 140–41
Browse · 127–52
Close Page · 126, 20
Colour Change (Analogue) · 126, 141–42
Colour Change (Digital) · 126, 142–43
Colour palette · 153
Create animation · 127–53
Delete animation · 123
Digital Colour Change · 126
Digital Colour Change · 142–43
Digital Display Value · 126, 145–46
Digital Edit Point Value · 126, 148–49
Digital User Input · 126, 148–49
Disable · 126, 143
Display Page · 126, 139
Display Status Text · 126, 145–46
Display Text Point · 126, 147–48
Display Value · 126
Display Value (Analogue) · 126, 146–47
Display Value (Digital) · 126, 145–46
Display Value (Text) · 126, 147–48
Edit Point Value (Analogue) · 126, 149–51
Edit Point Value (Digital) · 126, 148–49
Edit Point Value (Text) · 126, 151–52
Enable · 126, 143
Execute Script · 126. See also Script Editor
Expression dialog · 129
Expressions · 254
Release 1.2
OMRON
Height, Resize · 126, 136–37
Horizontal Move · 126, 133
Horizontal Percentage Fill · 126
Invisible · 126, 144–45
Modify animation · 127–53, 128
Move, Horizontal · 133
Move, Horizontal · 126
Move, Vertical · 126, 134–35
Object selection dialog · 130
Percentage Fill (Horizontal) · 126
Percentage Fill (Vertical) · 126, 138
Resize Height · 126, 136–37
Resize Width · 126, 135–36
Rotate · 126
Runtime · 127
Script, Execute · 126. See also Script Editor
Show Page · 126, 139
Text Display Value · 126, 147–48
Text Edit Point Value · 126, 151–52
Text User Input · 126, 151–52
Vertical Move · 126, 134–35
Vertical Percentage Fill · 126, 138
View · 122
Visible · 126, 144–45
Width, Resize · 126, 135–36
Animations
Aliases · 96, 130
Object animations · 127
Page animations · 124–25
Points · 121
Project animations · 123–24
Runtime · 127
Script · See Script Editor
Appendix D
Obsolete Features · 237
Application · 252
Applying Tooltips - Manipulating objects · 66
Arc - Creating/Editing Graphic Objects · 44
B
Bar Chart - Control Objects · 48
Bitmap · 252
Opening an existing bitmap · 50
Pixel · 256
Bitmap - Control Objects · 50
Block - Creating/Editing Graphic Objects · 44
Release 1.2
INDEX - CX-Supervisor User Manual
Boolean Point · 57
C
Changing the View Mode – Project Editor · 100
Changing the Viewing Mode - Point Editor · 25
Closing a Page - Saving a Page to a Project: · 20
Colour Palette - Graphics Editor: · 2
COM · 252
Communications Comtrol Properties · 219, 231
Communications Drive · 252
Compiling and Running a Project · 95
Configured Users - Runtime Security · 91
Configuring a Client PC under Win 95/98/Me
Running Windows 95/98 · 233
Configuring a client PC under Win NT/2000
Running Windows NT/2000 · 233
Configuring a PC for remote connection · 233
Configuring a Server PC under Win 95/98/Me
Running Windows 95/98 · 235
Configuring a Server PC under Win NT/2000
Running Windows NT/2000 · 234, 235
Connecting to a remote CX-Supervisor application · 223
Control Bar
Horizontal Mirror · 7
Lower Down One · 6
Object Identification · 5
Raise Up One · 5
Rotate · 6
Transparency On/Off · 7
Vertical Mirror · 7
Control Objects
Alarm Objects · 46
Bar Chart · 48
Bitmap · 50
Linear Gauge · 51
Pushbutton · 52
Rotary Gauge · 53
Scatter Graph · 54
Slider · 56
Toggle Button · 57
Trend Graph · 59
Control Tool Bar · 4
Conversation Attributes – Creating Points: · 32
Copy - Manipulating Objects · 62
Create Runtime Install Disc · 95
Creating a CX-Supervisor Client application · 226
Page 261
INDEX – CX-Supervisor User Manual
Creating a CX-Supervisor Server application · 225
Creating a Page · 13
Creating a PLC Connection – Device Configuration · 75
Creating a Point · 27
Advanced Point Setting · 32
Conversion Attributes · 32
Data Transfer Actions Update · 32
General Attributes · 27
I/O Attributes · 30
I/O Types · 29
I/O Update Rate · 30
Memory Attributes · 29
PLC Attributes · 31
Point Types · 27
Creating a project · 73
Creating and Editing Graphic Objects · 44
Creating Graphics Library - Graphics Library · 103
Creating/Editing Control Objects · 46
Creating/Editing Graphic Objects
Arc · 44
Block · 44
Ellipse · 44
Line · 45
Polygon · 45
Polyline · 45
Rectangle · 45
Round Rectangles · 45
Text · 46
Customising · 84
Customising CX-Supervisor · 2, 5
Cut - Manipulating Objects · 62
CX-Server · 253
CX-Supervisor customising · 2, 5, 84
CX-Supervisor Preferences · 20
D
Data Transfer Actions– Creating Points: · 32
Date Points - Point Import: · 39
DBCS · 211, 254
DCOM · 254
DDE · 237, 254
Server application · 257
Defining Properties of a Page · 14
Delete - Manipulating objects · 63
Deleting an Existing Point · 34
Device Configuration · 75
Page 262
OMRON
Display Points - Point Import: · 40
Distributed Server · 224
DLL · 254
Double Byte Character Set · See DBCS
Drop and Drag of Points - Point Editor · 25
Dynamic Data Exchange · See DDE
Dynamic Link Library · See DLL
E
Editing Objects · 43
Re-shaping · 43
Re-sizing · 43
Wozards · 44
Editing Preferences · 21
Ellipse - Creating/Editing Graphic Objects · 44
Error Logging Points - Point Import: · 40
Event/Error messages · 86–89
Column sorting · 88
Disable updates · 88
Display · 87
Enable updates · 88
Events · 88, 89
High priority errors · 88
Information · 89
Low priority errors · 88
Medium priority errors · 88
Show all events and errors · 88
Exit Level · 94
Extended Style Palettes - Graphics Editor: · 3
F
Fill Pattern Palette - Graphics Editor: · 3
Filtering Points in the View via Group - Point Editor ·
24
Filtering Points in the View via Point Type - Point
Editor · 24
Find Points · 96
Floating menu
Runtime environment · 84
Floating Menu - Manipulating objects · 66
Font
Alarms · 48
Release 1.2
OMRON
Charts · 49
Default button · 82
Gauges · 52, 54
Name · 10
Pushbutton · 52
Scatter graph · 55
Size · 10
Toggle button · 57
Trend graph · 60
Font Name – Text Bar: · 9
Font Size – Text Bar: · 10
G
Gauge
Wizard · See Wizard
General Attributes – Creating Points: · 27
General Preferences · 22
General settings · See Customising CX-Supervisor
General Settings
Runtime Settings · 82
Settings · 81
General Settings - Settings · 81
Graphical User Interface · See GUI
Graphics Editor · 1–11
About · 1
Access · 1
Bold · 11
Colour Palette · 2
Control Bar · 4–11
Extended Selection · 3
Fonts · 5–10
Grid · 11
Italics · 11
Justification · 11
Library, using the Graphics · 106
Lower down one · 6
Mirroring · 7
Object identity · 5
Object identity, modify · 5
Objects · 1, 2, 3, 4, 5, 6, 7, 11
Overview · 1
Palette · 1
Palettes, extending choice from · 3
Raise up one · 6
Status Bar · 11
Text · 5–11
Release 1.2
INDEX - CX-Supervisor User Manual
Text, bold · 11
Text, italics · 11
Text, underline · 11
Tool Box · 1–4
Tools Palette · 4
Transparency · 8
Underline · 11
Graphics Library · See Library
Activating the Library · 103
Creating Library · 103
Modify a Library · 104
Opening a Library · 104
Graphics Objects Tool Bar · 4
Graphs · See Trend Graph
Grid - Graphics Editor · 11
Group - Manipulating objects · 63
Group Attributes · 220
GUI · 255
H
Horizontal Mirror – Control Bar: · 7
I
I/O Attributes – Creating Points: · 30
I/O Types – Creating Points: · 29
I/O Update Rate – Creating Points: · 30
Icon · 255
Internal Points - Point Import: · 39
Item · 255
Item Attributes · 221
J
Java Script · See JScript
JScript · 255
JVM · 255
Page 263
INDEX – CX-Supervisor User Manual
K
Keyboard only control · 83, 150, 151
L
Language settings · 89
Library
About · 103
Access · 103
Adding a new object · 105
Copying an object from a library · 105
Creating a library · 103
Creating a new library file · 104
Default objects · 107
Editing library attributes · 104
Graphics Editor, using the · 106
Icon · 103
Print Graphics Library · See also Page, Preview
page; Page, Print page; Page, Setup page for
printing
Sharing · 107
View · 103
Line - Creating/Editing Graphic Objects · 45
Line Style Palette - Graphics Editor: · 2
Linear Gauge - Control Objects · 51
Linking Pages in a Project – Project Editor · 100
Lower Down One – Control Bar: · 6
M
Manipulating object
Alignment · 64
Alignment Toolbox · 64
Applying Tooltips · 66
Delete · 63
Floating Menu · 66
Group · 63
Mirror Image · 63
Orientation · 63
Paste · 62
Raise/Lower · 64
Transparency · 63
Page 264
OMRON
Undo · 63
Zoom · 65
Manipulating objects · 61
Manipulating Objects
Copy · 62
Cut · 62
Move · 62
Select · 61
Memory Attributes – Creating Points: · 29
Menu Option Access Levels - Runtime Security · 93
Microsoft
Word for Windows · 255
Mirror Image - Manipulating objects · 63
Modify Graphics Library - Graphics Library · 104
Modifying a PLC Connection – Device Configuration ·
78
Mouse Points - Point Import: · 40
Move - Manipulating Objects · 62
Multiple Selection – Project Editor · 101
N
Navigating Projects with the Workspace · 98
O
Object
About · 256
ActiveX Objects: · 67
Attributes · 105
Control object · 253
Control objects · 1, 46–61
Edit definition of an object · 106
Embedded objects · 1
Grab handles · 43–46
Graphic objects · 1, 44–46, 255
Manipulating an object · 61
Re-shaping an object · 43
Re-sizing an object · 43
Snapping objects to grid · 64
Text · 258
Text object · 1
Wizards · See Wizard
Object Identification – Control Bar: · 5
Release 1.2
OMRON
Objects · 43
Obsolete Features · 237
OLE Automation · 244
OPC
Foundation web site · 217
What is it? · 211, 212, 213, 214, 215, 217
Opening a Page via the Project Editor – Project Editor ·
99
Opening Graphics Library - Graphics Library · 104
Optimisation of PLC Communications – Device
Configuration · 37
Orientation - Manipulating objects · 63
Output workspace · 98
P
Page
About · 256
Access · 13
Attributes · 14–16, 14–16
Modify page · 13–14
Preview page · 17–18
Print page · 18–19. See also Page, Preview page;
Page, Setup page for printing; Print
Properties · 14–16, 14–16
Save page · 20, 74
Save page as a different identity · 20
Palette
Extended Palettes · 3
Fill Pattern Palette · 3
Line Style Palette · 2
Palette
Colour Palette · 2
Palette - Graphics Editor: · 1
Paste - Manipulating objects · 62
Peer to Peer · 224
PLC · 30, 31, 32, 75, 78, 79, 257
Accessing connection in runtime · 79
Attributes · 30
Configuration · 75
Creating a connection · 75
Deleting a connection · 79
Device type · 77
Modifying a connection · 78
Network · 77, 255
Optimising connections · 37
PLC Attributes – Creating Points: · 31
Release 1.2
INDEX - CX-Supervisor User Manual
PLC Communication Points - Point Import: · 41
Point Import · 37
Alarm Points · 40
Date Points · 39
Display Points · 40
Error Logging Points · 40
Internal Points · 39
Mouse Points · 40
PLC Communication Points · 41
Security Points · 41
Time Points · 38
Point Attributes
General Attributes · 28
Point Attributes – Creating Points: · 28
Point Editor · 23–25, 23–25, 23–25
About · 23
Access · 23
Changing the Viewing Mode · 25
Create point · 25–33
Delete point · 34
Dragging from · 25–26
Drop and Drag · 25
Filtering Points-via Group · 24
Filtering Points-via Point Type · 24
Modify point · 33
Sorting Points in the View · 24
Sorting Points-View by I/O Type · 24
Summary of Point Information · 25
View · 23–25, 23–25, 23–25
Point Types – Creating Points: · 27
Points
About · 23, 257
Alias definitions · 96, 130
Animation · 121, 128, 132
Boolean · 24, 27, 28, 38, 142, 145, 146, 148, 252
Constant · 253
Editor, Point · 23–25, 23–25, 23–25
Find · 96
Groups · 24, 27, 38
I/O type · 255
Information · 25
Integer · 24, 27, 28, 38, 146, 149, 150, 151, 255
Maintenance · 36
Non-volitile points · 256
Non-volitile rate · 84
Point Editor · 23–25, 23–25, 23–25
Print points · See also Page, Preview page; Page,
Print page; Page, Setup page for printing
Real · 24, 27, 28, 38, 146, 149, 150, 151, 257
Page 265
INDEX – CX-Supervisor User Manual
Runtime maintenance · 36
Script Editor · 132
Search · 96
Sort · 24
String · 257
System · 132
Text · 24, 29, 38, 147, 148, 258
Variable · 257
Polygon - Creating/Editing Graphic Objects · 45
Polyline - Creating/Editing Graphic Objects · 45
Print
Access · 18
Advanced options · 17, 19
Alarm/Message settings · 86
Alarms · 120
Collate copies · 19
Copies, number of · 19
Landscape orientation · 17
Number of copies · 19
Page preview · 17–18
Page print · 18–19
Paper size · 17
Paper source · 17
Portrait orientation · 17
Range · 19
Specific printer · 17
Print Preview
Printing a Page · 17
Print Preview - Printing Points: · 41
Print Preview – Printing from Project Editor · 101
Print Setup
Printing a Page · 16
Print Setup - Printing Points: · 41
Print Setup – Printing from Project Editor · 101
Printing
Printing a Page · 18
Printing - Printing Points: · 41
Printing – Printing from Project Editor · 101
Printing a Project · 75
Printing from Project Editor
Print Preview · 101
Print Setup · 101
Printing · 101
Printing Points
Print Preview · 41
Print Setup · 41
Printing · 41
Project
About · 73, 257
Page 266
OMRON
Adding pages to a project · 99
Advanced settings · 90
Alarm settings · 85
Alarm/Message printer settings · 86
Alias definitions · 130
Alias definitions · 96
Amending a Project · 74
Animations · 123
Colour palette · 81
Compiling a project · 95
Create runtime installation · 95
Creating a new project · 73
Creating a project · 73
Deleting pages from a project · 100
Editor, Project · See Project Editor
Event/Error messages · 87
Exit privilege · 94
Find points · 96
Font, default button · 82
Information · 74, 95, 100
Language settings · 89
Linking pages in a project · 100
Menu option access levels · 94
Modify a project · 74
Non-volatile rate · 84
Non-volitile point rate settings · 84
Opening a project · 74
Point substitution settings · 90
Printing · 75
Project Editor · See Project Editor
Running a project · 95
Saving a project · 74
Saving a Project · 74
Saving a runtime project · 95
Screen size · 85
Search for points · 96
Security · 91
Startup conditions · 82
Workspace · 98
Project Editor · 98
About · 99
Access · 98
Adding Pages · 99
Changing View Mode · 100
Linking Pages · 100
Multiple Selection · 101
Opening a Page · 99
Printing from · See also Page, Preview page; Page,
Print page; Page, Setup page for printing
Release 1.2
OMRON
Removing Pages · 100
Selecting Pages for Display · 100
View · 99
Viewing Project Details · 100
Viewing the Contents · 99
Project Information · 95
Project Workspace
Access · 98
Alarms view · 98
Project view · 98
Recipe view · 98
Pushbutton
Inserting a pushbutton · 52
Wizard · See Wizard
Pushbutton - Control Objects: · 52
R
Raise Up One – Control Bar: · 5
Raise/Lower - Manipulating objects · 64
Recipe Editor
About · 155
Access · 98, 156
Configuration attributes · 158
Copying recipe definition · 162
Create a recipe · 157
Create ingredient · 158
Delete ingredient · 161
Delete recipe · 162
Download recipes at runtime · 166
Information · 156
Ingredients · 158
Modify a recipe · 160
Modify ingredient · 161
Print recipes · See also Page, Preview page; Page,
Print page; Page, Setup page for printing
Runtime · 164
Security levels · 162
Terminology · 155
Validation · 159
View · 156
Recipes · See also Recipe Editor
About · 257
Download recipe · 254, 258
Download recipes · 166
Ingredients · 158, 255
Release 1.2
INDEX - CX-Supervisor User Manual
Print recipes · See also Page, preview page; Page,
print page; Page, setup page for printing
Runtime · 164
Security levels · 162
Validation · 159
Workspace · 98
Rectangle - Creating/Editing Graphic Objects · 45
Redundant Server · 225
Removing a PLC Connection – Device Configuration ·
79
Removing Pages from a Project – Project Editor · 100
Re-shaping Objects - Editing Objects · 43
Re-sizing Objects - Editing Objects · 43
Rotary Gauge - Control Objects · 53
Rotate – Control Bar: · 6
Round Rectangles - Creating/Editing Graphic Objects ·
45
Rremote connection to a CX-Supervisor application ·
223
Rubber Band · 61
Runtime
About · 257
Access PLC connection · 79
Advanced settings · 90
Alarm history · 119
Alarm reporting · 118
Alarm settings · 85
Alarm, acknowledge · 118
Alarm/Message printer settings · 86
Alarms, current · 119
Alarms, print · 120
Animations and scripts · 127–53
Create installation disc · 95
Event/Error messages · 87
Exit privilege · 94
Floating menu · 84
Language settings · 89
Menu option access levels · 94
Non-volitile point rate settings · 84
Point substitution settings · 90
Points maintenance · 36
Recipes · 164
Saving a project · 95
Screen size · 15, 85
Security · 91
Starting an application · 95
Startup conditions · 82
User configuration · 91
Viewing recipes · 164
Page 267
INDEX – CX-Supervisor User Manual
Runtime Point Maintenance · 36
Runtime Security
Access Levels · 93
Configured Users · 91
Runtime settings · See Customising CX-Supervisor
Runtime Settings - Settings · 82
S
Save Page As - Saving a Page to a Project: · 20
Save Runtime As · 95
Saving a Page to a Project · 20
Closing a Page · 20
Save Page As · 20
Saving a Project · 74
SCADA · 254, 257
Scatter Graph - Control Objects · 54
Screen size · 85
Script Editor · 127–33
About · 127
Alias definitions · 96, 130
AND statement · 252
Arguments · 252
Clear · 133
Compilation errors · 133
Completion · 133
Copy · 132
Cut · 132
Executable files, use of · 254
Execution attributes · 130
Expression dialog · 129
Nesting · 255
NOT statement · 256
Object selection dialog · 130
Operator and operand · 256
OR statement · 256
Paste · 132
Points · 132
Statements · 257
Tabulate · 132
Undo · 132
View · 128
Security · 91–94
Add a new user · 92
Designer user privilege · 91
Development environment user configuration · 91
Keyboard · 93
Page 268
OMRON
Login · 92
Logout · 93
Manager user privilege · 91
Menu option access levels · 94
Modify an existing user · 92
Operator user privilege · 91
Recipe levels · 162
Remove an existing user · 92
Required privilege for exit · 94
Runtime · 91
Runtime environment user configuration · 93
Supervisor user privilege · 91
User configuration, development environment · 91
User configuration, runtime environment · 93
Security Points - Point Import: · 41
Select - Manipulating Objects · 61
Selecting Pages for Display on Run – Project Editor ·
100
Settings · 81
Saving a Project · 81
Settings, general and runtime · See Customising CXSupervisor
Slider - Control Objects · 56
Sorting Points in the View - Point Editor · 24
Sorting Points in the View by I/O Type - Point Editor ·
24
Startup Preferences · 21
Status Bar · 8
Summary of Point Information - Point Editor · 25
Super Video Graphics Adapter · See SVGA
SVGA · 258
System points · 132
$12Hour · 38
$ActiveAlarms · 40
$AlarmCount · 40
$AMPM · 38
$AvailableMemory · 39
$Date · 39
$DayOfMonth · 39
$DayOfYear · 39
$DemoMode · 39
$DiskSpace · 39, 40
$HighAlarms · 40
$HighErrors · 41
$HighestAlarms · 40
$Hour · 38
$LowAlarms · 40
$LowErrors · 41
$LowestAlarms · 40
Release 1.2
OMRON
$MediumAlarms · 40
$MediumErrors · 41
$Millisecond · 38
$Minute · 38
$Month · 39
$MonthName · 39
$MouseX · 40
$MouseY · 40
$PLCBusy · 41
$PLCFailures · 41
$ScreenSizeX · 40
$ScreenSizeY · 40
$Second · 39
$SecurityLevel · 41
$SecurityName · 41
$ShortMonthName · 39
$ShortWeekDayName · 39
$ShortYear · 39
$Time · 39
$UnacknowledgedAlarms · 40
$UserName · 41
$WeekDay · 39
$WeekDayName · 39
$WeekOfYear · 39
$Year · 39
Description of · 38
System Points · 38
T
Text - Creating/Editing Graphic Objects · 46
Text - Editing text on a page · 44, 46
Text Bar · 9
Font Name · 9, 11
Font Size · 10
Text Bold On/Off · 11
Text Centered · 11
Text Italic On/Off · 11
Text Justified · 11
Text Underline On/Off · 11
Text Bold – Text Bar: · 11
Text Centered – Text Bar: · 11
Text Italics – Text Bar: · 11
Text Left Aligned – Text Bar: · 11
Text Right Aligned – Text Bar: · 11
Text Underline – Text Bar: · 11
Time Points - Point Import: · 38
Release 1.2
INDEX - CX-Supervisor User Manual
Toggle Button
Wizard · See Wizard
Toggle Button - Control Objects · 57
Transparency - Manipulating objects · 63
Transparency On/Off– Control Bar: · 7
Trend Graph
Inserting a trend graph · 59
Wizard · See Wizard
Trend Graph - Control Objects · 59
Two Tier, Client/Server or Master/Slave · 223
U
Undo - Manipulating objects · 63
Unicode · 211, 258
Using CX-Supervisor · 211, 217
Communications Control Properties · 219, 231
Group Attributes · 220
Item Attributes · 221
With Omrons OPC Server · 217, 229
V
VBScript · 258
Vertical Mirror – Control Bar: · 7
VGA · 258
Video Graphics Adapter · 258
Viewing Points · 24
Viewing Project Details – Project Editor · 100
Viewing the Contents of a Project – Project Editor · 99
Views
Details view · 25, 100, 111, 123, 156
Large icon view · 25, 100, 111, 123, 156
List view · 25, 100, 111, 123, 156
Small icon view · 25, 100, 111, 123, 156
Visual Basic · See VBScript
W
What is a Point · 23
What is OPC? · 211, 212, 213, 214, 215, 217
Windows Desktop · 258
Page 269
INDEX – CX-Supervisor User Manual
Windows Scripting Host · 258
Windows Taskbar · 258
Wizard · 258
Gauge Wizard · 52, 53
Pushbutton Wizard · 52
Slider Wizard · 56
Toggle Button Wizard · 57
Trend Graph · 59
Wizards - Editing Objects · 44
Page 270
OMRON
WSH · See Windows Scripting Host
Z
Zoom - Manipulating objects · 65
Release 1.2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement