2.4GHz Digital Wireless Rearview Camera with 7

2.4GHz Digital Wireless Rearview Camera with 7
USER MANUAL Model: VTC700R
Packing List
2.4GHz Digital Wireless Rearview
Camera with 7” Color LCD Monitor
Rearview Camera
TFT-LCD Monitor
Video Cable
Antenna for
Camera and
Monitor
Suction Holder
Stamping Mount
Holder
Monitor Power Supply
Cable
FOREWORD
In-Line Wire
Connectors
Congratulation. The Rearview Camera, when used as
described, will give you years of dependable service in
your car, truck, RV, or mini-van. We have taken numerous
measures in quality control to ensure that your product
arrives in top condition, and will perform to your
satisfaction.
Cigarette Lighter
Adapter
Grommet
The picture are for reference only, please refer to real subjects
For Sales Information Please Contact
Model: VTC700R
1
RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.
Wilmington, NC 28411
(800) 507-0482 / (910) 686-4281
Screw
STRUCTURE
For Sales Information Please Contact
RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.
Wilmington, NC 28411
(800) 507-0482 / (910) 686-4281
2
INSTALLATION
These installation instructions do not apply to all
vehicles. They are meant as only a general guide to big
vehicle makes & models. For specific questions, contact
your vehicle manufacturer. Consult your local motor
vehicle laws on the use of this product. Do not attempt
this if you are not knowledgeable with electrical
installation practices.
3. Insert the power
wire of the camera
into the supplied
grommet and then pass
the power wire into
the vehicle.
CAMERA INSTALLATION
1. You may mount the
camera near the top of
the license plate with
screws.
Notice
• The product is not suitable for mini vehicles.
• For specific vehicle such as container car or
container truck, please consult your local vehicle
garage for installation.
• Some vehicle may have a hole available to pass the
wire through, so you do not need to drill a hole.
• Before drilling those holes, you must check and make
sure no other components are in the way. Before
drilling, we strongly recommend you check carefully
for any possible interference to avoid unexpected
damages.
2. Drill six holes:
one hole for the
camera’s power wire
and five holes for
installation of the
camera.
For Sales Information Please Contact
RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.
Wilmington, NC 28411
(800) 507-0482 / (910) 686-4281
4. Install the camera
with five screws
supplied and adjust
the camera to a proper
angle.
3
CAMERA POWER WIRE CONNECTION
Insert the
existing wire to
be tapped.
1. Once you have located the reverse light circuit, you
need to route the power wire to that location. You
must securely fasten the power wire to prevent it
from being caught on a vehicle component such as the
trunk hinge. Never route the cable outside the
vehicle.
Insert the wire
to be attached.
Crimp tap and
then close lock
3. Wrap In-Line wire connectors over the camera power
wire.
For Sales Information Please Contact
2.
RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.
Wilmington, NC 28411
(800) 507-0482 / (910) 686-4281
The camera is equipped with Reverse Voltage
Protection. Please make sure that the RED wire is
connected to positive (+) and the Black wire is
connected to negative (-). Test by having someone
place the vehicle in Reverse. The correct wires will
have a 12 Volt DC potential only when the vehicle is
in Reverse.
4
Monitor Installation:
b) Use the cigarette lighter adapter to connect the
power socket of the monitor into the 12 Volt socket
of the vehicle.
1. Fastening the
suction cup holder
to the back of the
monitor.
2. Peel off the
backing paper of the
suction holder and
press it on the front
window of the vehicle.
4. Power on and the power indicator lights blue. Adjust
brightness, contrast and orientation of image on the
monitor.
THE WHOLE DIAGRAM OF INSTALLATION POSITION:
3. Connect power to the monitor. There are two methods as
below:
For Sales Information Please Contact
a) Wire directly to the vehicle fuse box, paying
attention to the positive and negative polarity.
5
RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.
Wilmington, NC 28411
(800) 507-0482 / (910) 686-4281
OPERATIONS
3. If the image on the LCD is unclear, adjust the
contrast, brightness and mirror by toggling the
buttons on the monitor.
1. Press the POWER button on the monitor for 3 seconds,
the power indicator will illuminate.
o Contrast Control: the 5 levels of LCD contrast
can be adjusted by pressing the CONTRAST
button.
2. This equipment has been paired successfully from the
factory. If there is no display image, you will need
to pair again.
o Brightness Control: the 5 levels of LCD
brightness can be adjusted by pressing the
BRIGHTNESS button.
Pairing Method: On the back of the Camera, there are 2
threaded holes with a button screw in the lower hole.
Unscrew the metal button in the lower hole and screw
it into the upper hole. Then on the front of the
monitor, press and hold the PAIRING button for 3s to
pair the frequency signal in 30 seconds. If pairing is
successful, remove the button screw from the top hole
in the Camera and screw it back into the bottom hole.
o There are four different views for the monitor.
If the image is not oriented correctly, press
the MIRROR button on the monitor to change the
orientation until it is correct.
o These different views allow you to mount the
camera and/or monitor with either right side up
or upside down and still display the image
correctly on the monitor. The image displayed
should match your rear view mirror. After
testing the unit, fully tighten the Camera
bolts.
For Sales Information Please Contact
RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.
Wilmington, NC 28411
(800) 507-0482 / (910) 686-4281
Notice:
Press the CONTRAST button for 4 seconds to reset the
display to the factory default.
6
SPECIFICATION
4.
The VTC700R Monitor has a video output that can be used to display the
Camera input on a larger monitor or TV screen. Connect the included RCA
cable to the monitor and the other end into the AV input of the larger monitor
or TV.
When the connection is successful, the following message will display on the C
A
monitor.
M
E
R
A
If the image does not display on TV, check the video cable and make sure it
is fully inserted into the monitor
R
E
C
E
I
V
E
R
For Sales Information Please Contact
RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.
Wilmington, NC 28411
(800) 507-0482 / (910) 686-4281
Items
Imaging Sensor
Total Pixels
Horizontal View Angle
Transmission Frequency
Minimum Illumination
IR Night Range
Modulating/Demodulating
Power Supply
Consumption Current (Max.)
Dimensions (W x D x H)
Approx. Weight
LCD Screen Type
Transmission Frequency
Screen Resolution
Video System
Received Sensitivity
Consumption Current (Max.)
Dimensions (W x D x H)
Approx. Weight
Power supply Voltage
* Unobstructed Effective
Range (Matching
Operating Temperature
Storage Temperature
Operating Humidity (Max.)
Value
CMOS
640x480
85º
ISM 2,400 – 2.483MHz
0 Lux (IR ON)
3m
16QAM,QPSK,BPSK
+12/+24VDC
150mA (IR OFF) & 230mA (IR ON)
96x52x61 (mm) (Excluding Bracket)
440g (15.5 Oz)
7” TFT-LCD
ISM 2,400~2,483MHz
800 x 480
NTSC/PAL
[email protected], [email protected]
600mA
214 x 26 x 157 (mm)
518g (Excluding Bracket)
DC 10-32V
<130m
0ºC~+40ºC
-20ºC~+60ºC
15%-85%RH
* The actual transmission range may vary according to
the weather, location, interference and building
construction.
* All the specifications are subject to minor change
without prior notice.
7
FCC INFORMATION
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation. Changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
CAUTIONS
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
Turn off the camera/receiver if the system is not in
use
The Camera/receiver can only be completely
disconnected form the mains by unplugging the adapter.
Do not cut the DC power cable of the apparatus to fit
with another power source.
Attention should be drawn to the environment aspects
of battery disposal.
For Sales Information Please Contact
RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.
Wilmington, NC 28411
(800) 507-0482 / (910) 686-4281
EU ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for
recycling advice.
This manual has been updated by RoadTrucker Inc
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement