Untitled

Untitled
EN 60065:2002+A1: 2006
Clause
Requirement – Test
3
GENERAL REQUIREMENTS
P
Safety class of the apparatus ................................. : Class II equipment
P
4
GENERAL CONDITIONS OF TESTS
P
4.1.4
Ventilation instructions require the use of the test
box
5
MARKING
5.1
Result - Remark
Verdict
No, tested according to the
instruction in the user’s
manual
P
P
Comprehensible and easily discernible
The rating label is easily
discernible.
P
Permanent durability against water and petroleum
spirit
After rubbing test by water and
petroleum spirit, the label still
easily discernible, indelible and
legible.
P
Identification, maker, model ................................... : Trade mark: GIEC
P
Model number: GK-B001
Class II symbol if applicable
Marked on the rear enclosure
P
Rated supply voltage and symbol .......................... : 220V-240V
P
Frequency if safety dependant
P
50/60Hz
Rated current or power consumption .................... : 10W
P
Earth terminal
No earth terminal
N
Hazardous live terminals
No hazardous live terminal
N
Supply output terminals (other than mains)
No supply output terminal
N
5.3
Use of triangle with exclamation mark
Marked on the circuit diagram
near every critical components
P
5.4
Instructions for use
Instruction for use provided in
user’s manual in English
P
5.4.1
Mains powered equipment not exposed to dripping Stated in the user’s manual
or splashing. Warning concerning objects filled
with liquid, etc.
P
Hazardous live terminals, instructions for wiring
No hazardous live terminals
N
Instructions for replacing lithium battery
No battery
N
Instructions for modem if fitted
No modem provided
N
Class I earth connection warning
Not class I equipment
N
5.2
Instructions for multimedia system connection
N
Special stability warning for fixed installation
Not fixed installation
N
Warning: battery exposure to heat
No battery
N
Warning: protective film on CRT face
No CRT
N
Report reference No.: WT093001905
Page 4 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
5.4.2
Disconnect device: plug/coupler or all-pole mains
switch location, accessibility and markings
Power plug used as
disconnect device
P
Instructions for permanently connected equipment
Not permanently connected
equipment
N
6
HAZARDOUS RADIATION
6.1
Ionizing radiation < 36 pA/kg (0,5 mR/h)
6.1
European Council Directive 96/29/Euratom of 13
May 1996 10cm from outer surface of apparatus
<1µSv/h (0,1mR/h)
N
Laser radiation, emission limits to IEC 60825-1 .... : No laser radiation
N
Emission limits under fault conditions .................... :
N
7
HEATING UNDER NORMAL OPERATING CONDITIONS
P
7.1
Temperature rises not exceeding specified values, (see appended table)
no operation of fuse links
P
7.1.1
Temperature rise of accessible parts
(see appended table)
P
7.1.2
Temperature rise of parts providing electrical
insulation
(see appended table)
P
7.1.3
Temperature rise of parts acting as a support or as
a mechanical barrier
7.1.4
Temperature rise of windings
(see appended table)
P
7.1.5
Parts not subject to a limit under 7.1.1 to 7.1.4
(see appended table)
P
7.2
Softening temperature of insulating material
supporting parts conductively connected to the
mains carrying a current > 0,2 A at least 150 oC
The input current was less
than 0.2A
N
8
CONSTRUCTIONAL REQUIREMENTS WITH REGARD TO THE PROTECTION
AGAINST ELECTRIC SHOCK
P
8.1
Conductive parts covered by lacquer, paper,
untreated textile oxide films and beads etc.
considered to be bare
Compliance checked by
inspection
P
8.2
No shock hazard when changing voltage setting
device, fuse-links or handling drawers etc.
No voltage setting device. It is
not possible for user to access
fuse-links. No indicators and
drawers used.
N
8.3
Insulation of hazardous live parts not provided by
hygroscopic material
No hygroscopic material used
as insulation
P
8.4
No risk of electric shock following the removal of a
cover which can be removed by hand
There is no risk of an electric
shock from accessible parts
P
8.5
Class I equipment
Not class I equipment
N
EN 60065
6.2
Report reference No.: WT093001905
N
No ionizing radiation
N
N
Page 5 of 49
EN 60065:2002+A1: 2006
Clause
8.6
8.8
8.9
Requirement – Test
Result - Remark
Verdict
Basic insulation between hazardous live parts and
earthed accessible parts
N
Resistors bridging basic insulation complying with
14.1 a)
N
Class II equipment and Class II constructions
within Class I equipment
P
Reinforced or double insulation between
hazardous live parts and accessible parts
Reinforced or double insulation
between hazardous live part
and accessible parts
P
Components bridging reinforced or double
insulation complying with 14.1 a) or 14.3
Transformer T1 bridging
primary and secondary circuit
complying with 14.3
P
Basic and supplementary insulation each being
bridged by a capacitor complying with 14.2.1 a)
No such capacitor used
N
Reinforced or double insulation being bridged with
2 capacitors in series complying with 14.2.1 a)
No such capacitor used
N
Reinforced or double insulation being bridged with
a single capacitor complying with 14.2.1 b)
Y1 capacitor separately
approved used
P
Basic insulation bridged by components complying Not used
with 14.3.4.3
N
Basic or supplementary insulation > 0,4 mm (mm) : The insulation of the primary
wire: 0.4mm+0.42mm
P
Reinforced insulation > 0,4 mm (mm) .................... : Enclosure (plastic): 2.3mm min
P
Thin sheet insulation (excluding non-separable thin
sheet insulation. See 8.22)
N
Basic or supplementary insulation, at least two
layers, each meeting 10.3
N
Basic or supplementary insulation, three layers any
two of which meet 10.3
N
Reinforced insulation, two layers each of which
meet 10.3
N
Reinforced insulation, three layers any two which
meet 10.3
N
Adequate insulation between internal hazardous
live conductors and accessible parts
Primary internal wire separate
from accessible parts by
double insulation
P
Adequate insulation between internal hazardous
live parts and conductors connected to accessible
parts
Internal hazardous live parts
separate form conductors
connectors connected to
accessible part by double
insulation
P
Report reference No.: WT093001905
Page 6 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
8.10
Double insulation between conductors connected
to the mains and accessible parts.
Double insulation used
P
Wires are well secured. No
wire is likely to become
detached.
See above
P
Double insulation between internal hazardous live
parts and conductors connected to accessible
parts.
8.11
Detaching of wires
No undue reduction of creepages or clearance
distances if wires become detached
Vibration test carried out ........................................ : See 12.1.2
N
P
No such part
8.13
Adequate fastening of windows, lenses, lamp
covers etc. (pull test 20 N for 10 s)
N
8.14
Adequate fastening of covers (pull test 50 N for
10 s)
8.15
No risk of damage to the insulation of internal
wiring due to hot parts or sharp edges
Internal wire well secured and
not likely to touch the hot parts
or sharp edge
P
8.16
Only special supply equipment can be used
Not such equipment
N
8.17
Insulated winding wire without additional
interleaved insulation
Triple insulation wire used as
the secondary coil of the
transformer
P
8.18
Endurance test as required by 8.17
The triple insulation wire has
been separately approved
N
8.19
Disconnection from the mains
See below
P
8.19.1
Disconnect device
Power plug used as disconnect
device
P
All-pole switch or circuit breaker with >3mm
contact separation
No switch
N
P
8.19.2
Mains switch ON indication
N
8.20
Switch not fitted in the mains cord
N
8.21
Bridging components comply with clause 14
No such component used
N
8.22
Non-separable thin sheet material
No such material used
N
9
ELECTRIC SHOCK HAZARD UNDER NORMAL OPERATING CONDITIONS
P
9.1
Testing on the outside
P
9.1.1
For voltages >1000 V ac or >1500 V dc complies
with clause 13.3.1 for basic insulation
9.1.1.1
a) Open circuit voltages
P
b) Touch current measured from terminal devices Results in appended table
using the network in annex D ................................. : 9.1.1. The measuring network
P
No voltage >1000 V ac or
>1500 V dc
according to annex D.
Report reference No.: WT093001905
Page 7 of 49
N
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
c) Discharge not exceeding 45 µC
< 1µC
P
d) Energy of discharge not exceeding 350 mJ
No voltage exceeding 15 kV
dc.
N
9.1.1.2
Test with test finger and test probe
No hazard live parts accessible
P
9.1.2
No hazardous live shafts of knobs, handles or
levers
No hazardous live shafts
9.1.3
Ventilation holes and other holes tested by means
of 4 mm x 100 mm test pin
No openings on top enclosure
9.1.4
Terminal devices tested with 1 mm x 20 mm test
pin (10 N); test probe D of IEC 61032
No hazard live parts accessible
Terminal devices tested with 1 mm x 100 mm
straight wire (1 N); test probe D of IEC 61032
No hazard live parts accessible
P
N
P
P
9.1.5
Pre-set controls tested with 2.5 mm x 100 mm test
No pre-set controls
pin (10 N); test probe C of IEC 61032
N
9.1.6
0V under normal condition
No shock hazard due to stored charge on
withdrawal of the mains plug; voltage (V) after 2 s : 0V under single fault condition
P
If C is not greater than 0,1 µF no test needed
N
a) Enclosure sufficiently resistant to external force
P
9.1.7
Test probe 11 of IEC 61032 for 10 s (50 N)
No damage
P
b) Test hook of fig. 4 for 10 s (20 N)
No damage
P
c) 30 mm diameter test tool for 5 s (100 or 250 N) : No damage
P
9.2
No hazard after removing a cover by hand
N
10
INSULATION REQUIREMENTS
P
10.1
Insulation resistance (MΩ) at least 2 MΩ min. after Surge test with 50 discharges
at a rate of maximum 12/min
surge test for basic and 4 MΩ min. for reinforced
insulation ................................................................. : from a 1nF capacitor charged
to 10 kV performed. Measured
greater than 4M between the
circuit connect to hazards
parts and circuit not connect
to hazards parts.
P
10.2
Humidity treatment 48 h or 120 h ........................... : 48h
P
10.3
Insulation resistance and dielectric strength
between mains terminals
P
Insulation Resistance and dielectric strength
across BASIC or SUPPLEMENTARY insulation
(Class 1)
N
Insulation resistance and dielectric strength across (see appended table)
REINFORCED insulation (Class II)
P
Report reference No.: WT093001905
No removable cover by hand
Page 8 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
11
FAULT CONDITIONS
11.1
No shock hazard under fault condition
No electric shock during fault
operation.
P
11.2
Heating under fault condition
No excessive temperature
P
No hazard from softening solder
No solder softened during the
test.
N
Flames extinguish within 10 seconds
No flames in fault condition
tests
P
P
Soldered terminations not used as protective
mechanism
P
11.2.1
Measurement of temperature rises
(see appended table)
P
11.2.2
Temperature rise of accessible parts
(see appended table)
P
11.2.3
Temperature rise of parts, other than windings,
providing electrical insulation
(see appended table)
P
Temperature rise of printed circuit boards (PCB)
exceeding the limits of table 3 by max. 100 K for
max. 5 min
PCB temperature rise didn’t
exceed the limits of table 3.
N
a) Temperature rise of printed circuit boards (PCB)
to 20.1.3, exceeding the limits of table 3 by not
more than 100 K for an area not greater than 2 cm²
N
b) Temperature rise of printed circuit boards (PCB)
to 20.1.3 up to 300 K for an area not greater than
2 cm² for a maximum of 5 min
N
Meets all the special conditions if conductors on
printed circuit boards are interrupted
N
Class I protective earthing maintained
Not class I equipment
N
11.2.4
Temperature rise of parts acting as a support or
mechanical barrier
(see appended table)
P
11.2.5
Temperature rise of windings
(see appended table)
P
11.2.6
Temperature rise of parts not subject to the limits
of 11.2.1 to 11.2.5
(see appended table)
P
12
MECHANICAL STRENGTH
12.1.1
Bump test where mass >7 kg
Less than 7 kg
N
12.1.2
Vibration test
No damage
P
12.1.3
Impact hammer test
0.5J, three times. No damage
P
Steel ball test
2J on top, side back and front
enclosure. No damage.
P
12.1.4
Drop test for portable apparatus where mass < 7
kg
Not portable apparatus
N
12.1.5
Thermoplastic enclosures strain relief test
70℃ for 7h. No hazard live part
become accessible
P
Report reference No.: WT093001905
P
Page 9 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
12.2
Fixing of knobs, push buttons, keys and levers
12.3
Remote controls with hazardous live parts
No such remote controls
N
12.4
Drawers (pull test 50 N, 10 s)
No drawer
N
12.5
Antenna coaxial sockets providing isolation
No antenna coaxial socket
providing isolation
N
12.6
Telescoping or rod antennas construction
No such device
N
12.6.1
Telescoping or rod antennas securement
No such device
N
13
CLEARANCE AND CREEPAGE DISTANCES
P
13.1
Clearances in accordance with 13.3
P
Creepage distances in accordance with 13.4
P
N
13.2
Determination of operating voltage
Considered
P
13.3
Clearances
(see appended table)
P
13.3.1
General
P
13.3.2
Circuits conductively connected to the mains
comply with table 8 and, where applicable, table 9
P
13.3.3
Circuits not conductively connected to the mains
comply with table 10
P
13.3.4
Measurement of transient voltages
N
13.4
Creepage distances
(see appended table)
P
Creepage distances greater than table 11 minima
P
13.5
Printed boards
P
13.5.1
Clearances and creepage distances between
conductors on printed circuit boards, one of which
may be conductively connected to the mains, as in
fig. 10
P
13.5.2
Type B coated printed circuit boards complying
with IEC 60664-3 (basic insulation only)
No such printed board used
N
13.6
Conductive parts along uncemented joints
clearances and creepage distances comply with
13.3 and 13.4
No such part
N
Conductive parts along reliably cemented joints
comply with 8.8
N
Temperature cycle test and dielectric strength test
N
13.7
Enclosed, enveloped or hermetically sealed parts:
not conductively connected to the mains:
clearances and creepage distances as in table 12
N
13.8
Parts filled with insulating compound, meeting the
requirements of 8.8
Report reference No.: WT093001905
Optocoupler separately
approved
Page 10 of 49
P
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
14
COMPONENTS
P
14.1
Resistors
N
a) Resistors between hazardous live parts and
accessible metal parts
14.2
Verdict
No such component
N
b) Resistors, other than between hazardous live
parts and accessible parts
N
Resistors separately approved .............................. :
N
Capacitors and RC units
P
Capacitors separately approved
P
nd
14.2.1
Y capacitors tested to IEC 60384-14, 2 edition .. : Y capacitors separately
approved
P
14.2.2
X capacitors tested to IEC 60384-14, 2nd edition .. : X capacitors separately
approved
P
14.2.3
Capacitors operating at mains frequency but not
connected to the mains: tests for X2 ..................... :
N
14.2.5
Capacitors with volume exceeding 1750 mm³,
No such capacitor
where short-circuit current exceeds 0,2 A:
compliance with IEC60384-1, 4.38 category B or
better ....................................................................... :
N
Capacitors with volume exceeding 1750 mm³,
mounted closer to a potential ignition source than
table 5 permits: compliance with IEC 60 384-1,
4.38 category B or better ........................................ :
N
Shielded by a barrier acc. to 20.1.4/ table 21 or
metal ....................................................................... :
N
Inductors and windings
P
14.3
Comply with IEC 61558-1, IEC 61558-2
(as relevant) and clause 20.1.4
14.3.1
14.3.2
Tested with the equipment
N
Transformers and inductors marked with
Marked with the code
manufacturer's name and type .............................. :
P
Transformers and inductors separately approved : Tested in unit
N
General
P
Insulation material complies with clause 20.1.4
Refer to 20.1.4
P
14.3.3
Constructional requirements
14.3.3.1
Clearances and creepage distances comply with
clause 13
14.3.3.2
Transformers meet the constructional
requirements
P
14.3.4.1
Class II transformers have adequate separation
Primary separately from
between hazardous live parts and accessible parts secondary coil by reinforced
(double or reinforced insulation)
insulation
P
Report reference No.: WT093001905
P
See clause 13
P
Page 11 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Coil formers and partition walls > 0,4 mm
Bobbin of T1: > 0.9 mm
P
14.3.4.2
Class I transformers, with basic insulation and
protective screening only if all 7 conditions of
14.3.4.2 are met
Class II transformer
N
14.3.4.3
Separating transformers with at least basic
insulation
No separating transformer
N
14.3.5.1
Class II transformers have adequate insulation
Primary separately from
between hazardous live parts and accessible parts secondary coil by reinforced
(double or reinforced insulation)
insulation
P
Coil formers and partition walls > 0,4 mm
P
14.3.5.2
14.4
Verdict
Bobbin of T1: > 0.9 mm
Class I transformers have adequate insulation
between hazardous live parts and accessible
conductive parts or those conductive parts or
protective screens connected to a protective earth
terminal
N
Winding wires connected to protective earth have
adequate current-carrying capacity
N
High voltage components
No high voltage component
N
High-voltage components and assemblies:
U > 4 kV (peak) separately approved
N
Component meets category V-1 of IEC 60707
N
14.4.1
High voltage transformers and multipliers tested as
part of the submission
N
14.4.2
High voltage assemblies and other parts tested as
part of the submission
N
14.5
Protective devices
P
Protective devices used within their ratings
P
External clearances and creepage distances meet See clause 13
requirement of clause 13 for the voltage across the
device when opened
P
a) Thermal cut-outs separately approved
N
14.5.1.1
No thermal cut-out
b) Thermal cut-outs tested as part of the
submission
14.5.1.2
a) Thermal links separately approved
N
No thermal link
N
b) Thermal links tested as part of the submission
N
14.5.1.3
Thermal devices re-settable by soldering
No such device
N
14.5.2.1
Fuse-links in the mains circuit according to IEC
60127
Fuse link separately approved
P
14.5.2.2
Correct marking of fuse-links adjacent to holder ... : “T 630mAL250V” marked near
the fuse link on the PCB board
P
14.5.2.3
Not possible to connect fuses in parallel ............... :
P
Report reference No.: WT093001905
Page 12 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
14.5.2.4
Not possible to touch hazardous live parts when
Tools need to replace the fuse
replacing fuse-links without the use of a tool ......... : link
N
14.5.3
PTC-S thermistors comply with IEC 60730-1
N
No PTC-S thermistor
PTC-S devices (15 W) category V-1 or better
N
14.5.4
Circuit protectors have adequate breaking capacity
and their position is correctly marked
N
14.6
Switches
14.6.1 a)
Separate testing to IEC 61058 including:
No switch
N
N
10 000 operations
Normal pollution suitability
Resistance to heat and fire level 3
and
Make and break speed independent of speed of
actuation
V-0 compliance with annex G, G.1.1
14.6.1 b)
Tested in the apparatus:
N
Switch controlling > 0.2A with open contact
voltage > 35 V (peak)/24 V dc complying with
14.6.3, 14.6.4 and V-0 in annex G, G.1.1
N
Switch controlling > 0.2A with open contact
voltage < 35 V (peak)/24 V dc complying with
14.6.3 and V-0 in annex G, G.1.1
N
Switch controlling < 0.2A with open contact
voltage > 35 V (peak)/24 V dc complying with
14.6.4 and V-0 in annex G, G.1.1
N
14.6.2
Switch tested to 14.6.1 b) constructed to IEC
61058-1 subclause 13.1 and has making/breaking
action independent of speed of actuation
N
14.6.3
Switch tested to 14.6.1 b) compliant with IEC
61058-1 subclause 16.2.2 d) and m) not attaining
excessive temperatures in use
N
14.6.4
Switch tested to 14.6.1 b) has adequate dielectric
strength
N
14.6.5
Mains switch controlling mains socket outlets
additional tests to IEC 60058-1
N
14.7
Socket outlet current marking correct
No socket outlet
N
Safety interlocks
No such devices.
N
Safety interlocks to 2.8 of IEC 60950
14.8
Voltage setting devices and the like
Report reference No.: WT093001905
N
No such devices.
N
Page 13 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
Voltage setting device not likely to be changed
accidentally
N
No motor
14.9
Motors
14.9.1
Endurance test on motors
N
Motor start test
N
Dielectric strength test
N
14.9.2
Not adversely affected by oil or grease etc.
N
14.9.3
Protection against moving parts
N
14.9.4
Motors with phase-shifting capacitors, three-phase
motors and series motors meet clause. B.8, B.9
and B.10 of IEC 60950, Annex B
N
14.10
Batteries
14.10.1
Batteries mounted with no risk of accumulation of
flammable gases
N
14.10.2
No possibility of recharging non-rechargeable
batteries
N
14.10.3
Recharging currents and times within
manufacturers limits
N
Lithium batteries discharge and reverse currents
within the manufacturers limits
N
14.10.4
Battery mould stress relief
N
14.10.5
Battery drop test
N
14.11
Optocouplers
14.12
N
No battery used
N
Separately approved
P
Optocouplers comply with Cl. 8
P
Internal and external dimensions to 13.1. or
alternatively 13.6 (jointed insulation)
P
Surge suppression varistors
No surge suppression varistor
N
Comply with IEC 61051-2
N
Not connected between mains and accessible
parts except for earthed parts of permanently
connected apparatus
N
Complies with the current pulse, fire hazard and
thermal stress requirements of 14.12
N
15
TERMINALS
P
15.1.1
Mains plug, appliance inlet, interconnection
couplers and mains socket-outlet meet the
appropriate standard
Report reference No.: WT093001905
Mains plug separately
approved according to the
appropriate standard
Page 14 of 49
P
EN 60065:2002+A1: 2006
Clause
15.1.2
Requirement – Test
Result - Remark
Verdict
Overloading of plugs or appliance inlets prevented No mains socket outlet
if the apparatus has mains socket outlets
N
Overloading of internal wiring prevented if the
apparatus has mains socket outlets
N
No mains socket outlet
Connectors for antenna, earth, audio, video or data:
P
No risk of insertion in mains socket-outlets
None of mismatch of
connectors to AC mains
occurred.
P
No risk of insertion into audio or video: outlets
marked with the symbol of 5.2
No sockets indicated with the
symbol.
N
15.1.3
Output terminals of a.c. adaptors or similar devices No such device
not compatible with household mains socketoutlets
N
15.2
Provision for protective earthing
N
Accessible conductive parts of Class I equipment
reliably connected to earth terminal, within
equipment
Class II equipment
N
Protective earth conductors correctly coloured
N
Equipment with non-detachable mains cord
provided with separate protective earth terminal
near mains input
N
Protective earth terminal resistant to corrosion
N
Earth resistance test: < 0,1 Ω at 25 A ................... :
N
15.3
Terminals for external flexible cords and for
permanent connection to the mains supply
P
15.3.1
Adequate terminals for connection of permanent
wiring
15.3.2
Reliable connection of non-detachable cords:
P
Not soldered to conductors of a printed circuit
board
P
Adequate clearances and creepage distances
between connections should a wire break away
Not permanent connected
equipment
No wire is likely to break away
N
P
Wire secured by additional means to the conductor
P
15.3.3
Screws and nuts clamping conductors have
adequate threads: ISO 261, ISO 262 or similar
N
15.3.4
Soldered conductors wrapped around terminal
prior to soldering or held in place by additional
means
N
Clamping of conductor and insulation if not
soldered or held by screws
N
Report reference No.: WT093001905
Page 15 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
15.3.5
Terminals allow connection of appropriate crosssectional area of conductors, for the rated current
of the equipment
N
15.3.6
Terminals to 15.3.3 have sizes required by
table 16
N
15.3.7
Terminals clamp conductors between metal and
have adequate pressure
N
Terminals designed to avoid conductor slipping out
when tightened or loosened
N
Terminals adequately fixed to avoid loosening
when the clamping is tightened or loosened and
stress on internal wiring is avoided
N
15.3.8
Terminals carrying a current more than 0,2 A:
contact pressure not transmitted by insulating
material except ceramic
N
15.3.9
Termination of non-detachable cords: wires
terminated near to each other
P
Terminals located and shielded: test with 8 mm
strand
N
15.4
Devices forming a part of the mains plug
Not direct plug-in equipment
N
15.4.1
No undue strain on mains socket-outlets
15.4.2
Device complies with standard for dimensions of
mains plugs
15.4.3
Device has adequate mechanical strength (tests
a,b,c)
N
16
EXTERNAL FLEXIBLE CORDS
P
16.1
VDE approved IEC 60227
Mains cords sheathed type, complying with
PVC cord used
IEC 60227 for PVC or IEC 60245 for synthetic
rubber cords ............................................................ :
P
Non-detachable cords for Class I have
green/yellow core for protective earth
N
N
Class II equipment
16.2
Mains cords conductors have adequate cross0.5mm2, the length of the
sectional area for rated current consumption of the power supply cord is less than
equipment
2m
16.3
a) Flexible cords not complying with 16.1, used for
interconnections between separate units of
equipment used in combination and carrying
hazardous live voltages, have adequate dielectric
strength
No such flexible cords.
N
b) Flexible cords not complying with 16.1,
withstand bending and mechanical stress (3.2 of
IEC 60227-2)
No such flexible cords.
N
Report reference No.: WT093001905
Page 16 of 49
P
EN 60065:2002+A1: 2006
Clause
Requirement – Test
16.4
Flexible cords used for connection between
No such flexible cord
equipment have adequate cross-sectional areas to
avoid temperature rise under normal and fault
conditions
N
16.5
Adequate strain relief on external flexible cords
P
Not possible to push cord back into equipment
P
Strain relief device unlikely to damage flexible cord
P
For mains cords of Class I equipment, hazardous
live conductors become taut before earth
conductor
16.6
Apertures for external flexible cord: no risk of
damage to the cord during assembly or movement
in use
16.7
Transportable musical instruments and amplifiers
fitted with detachable cord set with appliance inlet
to IEC 60320-1
Result - Remark
Verdict
Class II equipment
N
P
Not transportable musical
instrument
N
Transportable musical instruments and amplifiers
fitted with detachable cord sets or with means of
stowage to protect the cord
N
17
ELECTRICAL CONNECTIONS AND MECHANICAL FIXINGS
P
17.1
Torque test to table 20:
P
- screws into metal: 5 times
Enclosure fixing and PCB
fixing screws: Φ3.0mm, tested
with 0.5Nm torque
P
- screws into non-metallic material: 10 times
N
17.2
Correct introduction into female threads in nonmetallic material
N
17.3
Cover fixing screws: captive
No captive screw used
N
Non-captive fixing screws: no hazard when
replaced by a screw whose length is 10 times its
diameter
No clearance and creepage
distance will reduce to below
the requirement.
P
17.4
No loosening of conductive parts carrying a current
> 0,2 A
N
17.5
Contact pressure not transmitted through plastic
other than ceramic for connections carrying a
current > 0,2 A
N
17.6
Stranded conductors of flexible supply cords
carrying a current > 0,2 A with screw terminals not
consolidated by solder
N
17.7
Cover fixing devices other than screws have
adequate strength and their positioning is
unambiguous
Report reference No.: WT093001905
No cover
N
Page 17 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
17.8
Fixing devices for detachable legs or stands
provided
No such device
N
17.9
Internal pluggable connections, affecting safety,
unlikely to become disconnected
N
18
MECHANICAL STRENGTH OF PICTURE TUBES AND PROTECTION AGAINST
THE EFFECTS OF IMPLOSION
N
Picture tube separately approved to IEC 61965:
N
No picture tube
Picture tube separately approved to 18.1 .............. :
N
Picture tubes > 16 cm intrinsically protected
N
Non-intrinsically protected tubes > 16 cm used with
protective screen
N
Protective film as part of implosion protection:
edges covered by enclosure
N
18.2
Intrinsically protected tubes: tests on 12 samples
N
18.2.1
Samples subject to ageing: 6
N
18.2.2
Samples subject to implosion test: 6
N
18.2.3
Samples subject to mechanical strength test (steel
ball): 6
N
18.3
Non-intrinsically protected tubes tested to 18.3
N
19
STABILITY AND MECHANICAL HAZARDS
P
Mass of the equipment exceeding 7 kg ................. : Less than 7 kg
N
Apparatus intended to be fastened in place –
suitable instructions
N
19.1
Test on a plane, inclined at 10o to the horizontal
N
19.2
100 N force applied vertically downwards
N
19.3
100 N force, or 13% of weight, applied horizontally
to point of least stability.
N
19.4
Edges or corners not hazardous
Edges and corners are
smoothed
P
19.5
Glass surfaces (exc.laminated) with an area
exceeding 0,1 m² or maximum dimension
> 450 mm, pass the test of 19.5.1
No glass surface
N
19.6
Wall or ceiling mountings adequate
N
20
RESISTANCE TO FIRE
P
20.1
Electrical components and mechanical parts
P
18.1
Report reference No.: WT093001905
Page 18 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
a) Exemption for components contained in an
enclosure of material V-0 to IEC 60707 with
openings not exceeding 1 mm in width
N
b) Exemption for small components as defined in
20.1
Some small components
mounted on UL listed PCB with
flammability of V-0.
P
20.1.1
Electrical components meet the requirements of
Clause 14 or 20.1.4
Considered complied for
adapter itself.
P
20.1.2
Insulation of internal wiring working at voltages
> 4 kV or leaving an internal fire enclosure, not
contributing to the spread of fire
Internal wiring working at
voltages not exceeding 4kV.
N
20.1.3
Material of printed circuit boards on which the
available power exceeds 15 W at a voltage
between 50 V and 400V (peak) a.c. or d.c. meets
V-1 or better to IEC60707, unless used in a fire
enclosure
V-0 PCB used
P
Material of printed circuit boards on which the
See above
available power exceeds 15 W at a voltage >400 V
(peak) a.c. or d.c. meets V-0 to IEC 60707
20.1.4
Components and parts not covered by 20.1.1,
20.1.2 and 20.1.3 (other than fire enclosures)
mounted nearer to a potential ignition source than
the distances in Table 21 comply with the relevant
flammability category in Table 21
P
See clause 14
P
Components and parts as above but shielded from
a potential ignition source, with the barrier area in
accordance with Table 21 and fig. 13
N
20.2
Fire enclosure
N
20.2.1
Potential ignition sources with open circuit voltage
> 4 kV (peak) a.c. or d.c. contained in a fire
enclosure to V-1
No voltage > 4 kV.
N
20.2.2
Internal fire enclosures with openings not
exceeding 1 mm in width and with openings for
wires completely filled
No internal fire enclosure
N
20.2.3
Requirements of 20.2.1 and 20.2.2 met by an
internal fire enclosure
Report reference No.: WT093001905
N
Page 19 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
A
APPENDIX A, ADDITIONAL REQUIREMENTS FOR APPARATUS WITH
PROTECTION AGAINST SPLASHING WATER
N
A.5.1
j) Marked with IPX4 (IEC 60529), 5.4.1 a) does not
apply
N
A.10.2.1
Enclosure provides protection against splashing
water
N
A.10.2.2
Humidity treatment carried out for 7 days
N
B
APPENDIX B, APPARATUS TO BE CONNECTED TO THE
TELECOMMUNICATION NETWORKS
N
Complies with IEC 62151 clause 1
N
Complies with IEC 62151 clause 2
N
Complies with IEC 62151 clause 3 but with 3.5.4
modified to 2.4.10 of this standard
N
Complies with IEC 62151 clause 4 but with 4.1.2,
4.1.3 and 4.2.1.2 modified in accordance with
annex B of this standard
N
Complies with IEC 62151 cause 5 but with 5.3.1
modified in accordance with annex B of this
standard
N
Complies with IEC 62151 clause 6
N
Complies with IEC 62151 clause 7
N
Complies with IEC 62151 annex A, B and C
N
L
APPENDIX L, ADDITIONAL REQUIREMENTS FOR ELECTRONIC FLASH
APPARATUS FOR PHOTOGRAPHIC PURPOSES.
N
L5.4
Marking and Instructions
N
L9.1.1
Terminals to connection to synchroniser not
HAZARDOUS LIVE
N
L7.1.5 &
Lithium batteries meet permissible temp rise in
Table 3, unless comply with 6.3.2 of IEC 60086-4
N
Mains switch characteristics appropriate to its
function under normal conditions
N
L11.2.6
L14.6.6
Report reference No.: WT093001905
Result - Remark
Verdict
Page 20 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
GROUP DIFFERENCES (CENELEC common modifications) and special national conditions
according to CB Bulletin No. 112A, December 2006
P
EN 60065:2002+A1:2006
(IEC Publication 60065:2001+A1:2005)
EXPLANATION FOR ABBREVIATIONS
C=CENELEC common modification, S=Special national conditon
P=Pass, F=Fail, N/A=Not applicable. Placed in the column to the right
CONTENT
Add the following annexes:
P
Annex ZA (normative) Other international publications quoted in this standard with
the references of the relevant European publications
Annex ZB (normative) Special national conditions
Annex ZC (informative) A-deviations
2.6.1
S(DK)
Class II equipment
P
The following is added:
Certain types of CLASS I apparatus, see 15.1.1, may be
provided with a plug not establishing earthing continuity
when inserted in Danish socket-outlets.
Justification:
Heavy Current Regulations, Section 107
3.1
N
C: Add the following indent at the end of the list:
exposure to excessive sound pressures from headphones or
earphones.
NOTE A new method of measurement is described in EN
50332-1, Sound system equipment: Headphones and
earphones associated with portable audio equipmentMaximum sound pressure level measurement methodology
and limit consideration- Part 1: General method for “one
package equipment”, and in EN 50032-2, Sound system
equipment:
Headphones and earphones associated with portable audio
equipment- Maximum sound pressure level measurement
methodology and limit considerations- Part 2: Gudielines to
associate sets with headphones coming from different
manufactures.
4.1.1
C: Replace the text of the note by:
N
NOTE For ROUTINE TEST reference is made to EN 50333
5
S(DE)
No cathode-ray tube
The following marking are required:
In case of intrinsically ionizing radiation safe cathode-ray
tubes with accelerating voltages betwwen 20kV and 30kV:
Report reference No.: WT093001905
Page 21 of 49
N
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
- On the cathode-ray tube itself the wording:
Eigensichere Kathodenstrahlröhre nach Anlage III Röntgenverordnung
- Inside the apparatus:
the maximum allowed accelerating voltage in kV, and the
maximum allowed beam current in mA.
- On the outer of the apparatus:
a notice in German language that produced X-rays are
sufficiently shielded
by the intrinsically safe cathode-ray tube.
In case of approval of the whole TV receiver with an
accelerating voltage exceeding 20 kV:
- On the outer of the apparatus:
the licence number .../.../.../Rö, and the following text:
Die in diesem Gerät entstehende Röntgenstrahlung ist
ausreichend abgeschirmt. Beschleunigungsspannung:
max: ... kV.
- Supplied with the apparatus:
a copy of the "Zulassungsschein", together with the notices
required there.
In case of TV receivers with accelerating voltages not
exceeding 20 kV:
Die in diesem Gerät entstehende Röntgenstrahlung ist
ausreichend abgeschirmt. Beschleunigungsspannung:
max: ... kV.
Justification:
German ministerial decree against ionizing radiation
( Röntgenverordnung), dated 1987-01-08.
NOTE The German ministerial decree (Röntgenverordnung)
is under revision.
S(DE)
No cathode-ray tube
Annex ZC
Delete the A-deviation for Clause 5 for Germany and add
the following new A-deviation:
Clause National deviation
Germany
Report reference No.: WT093001905
Page 22 of 49
N
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
6.1 The following requirement applies:
For the operation of the any cathode ray tube intended for
the display of visual images
Operating at an acceleration voltage exceeding 40kV,
authorization is required, or
Application of type approval (Bauartzulassung) and marking.
Justification:
German ministerial decree against ionizing radiation
(Röntgenverordnung), in force since 2002-07-01,
implementing the European Directive 96/29/EURATOM.
NOTE Contact address:
Physikalisch-Tchnische Bundesanstalt, Bundesallee 100, D38116 Braunschweig,
Tel.: Int+49-513-592-6320, Internet: http:// www.ptb.de
5.1
5.1.i)
IT: additional marking on the outside of the TV receiver in
Italian language
Not TV receiver
N
IT: user instructions in Italian language including a
conformity declaration
N
IT: certificatino number on the back cover
N
C: Replaced the note by:
N
NOTE For RATED POWER CONSUMPTION
measurements of TVs reference is made to EN 62087.
Measurements are done in the ON (play) operating mode.
5.4.1
C: Add the following indent:
Za) A warning that excessive sound pressure from
earphones and headphones can cause hearing loss
Report reference No.: WT093001905
No earphone or
headphone
Page 23 of 49
N
EN 60065:2002+A1: 2006
Clause
Requirement – Test
6.1
C: Replace the subclause by:
Result - Remark
Verdict
No ionizing radiation
N
6.1 Ionizing radiation
Equipment that might produce ionizing radiation is checked
by measuring the amount of radiation.
The amount of radiation is determined by means of a
radiation monitor of the ionizing chamber type with an
effective area of 1000m2 or by measuring equipment of
other types giving equivalent result.
Measurements are made with the equipment on test
operating at the most unfavourable supply voltage (see 4.2)
and with operator controls and service controls adjusted so
as to give maximum radiation whilst maintainning the
equipment operative for normal use.
Internal preset controls not intended to be adjusted during
the lifetime of the equipment are not considered to be
serivce controls.
At any point 100mm from the surface of the operator access
area, the dose-rate shall not exceed 1μSv/h (0.1 mR/h)
(see Note). Account shall be taken of the background level.
NOTE These values appear in Directive 96/29/Euratom
13.3.1
C: Delete note 4
13.3.1
S (NO)
P
Considered
P
To the second paragraph the following is added:
In Norway, due to the IT power distribution system used, the
a.c. MAINS supply voltage is considered to be equal to the
line-to-line voltage, and will remain 230V in case of a single
earth fault will remain 230V in case of a single earth fault.
Justification:
Based on a use in Norway of an IT power distribution
system where the neutral is not provided.
14
C: Delete not 4 and not 5.
P
15.1.1
C: Delete note 1 and note 2.
P
15.1.1
S (DK)
No socket outlet used
To the first paragraph the following is added:
In Denmark, supply cords of single phase appliances having
a rated current not exceeding 13A shall be provided with a
plug according to the Heavy Current Refulations Section
107-2-D1.
Appliances of CLASS I provided with socket-outlets with
earth contact or which are intended to be used in locations
where protection against indirect contact is required
according to the wiring rules shall be provided with a plug in
accordance with the Heavy Current Regulations, Section
Report reference No.: WT093001905
Page 24 of 49
N
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
107-2-D1 standard sheet DK 2-1a.
To the second paragraph the following is added:
Socket outlets intended for providing power to CLASS II
apparatus with a rated current of 2,5 A shall have the
following dimensions:
Dimensions in mm
Other dimensions shall be in compliance with the Heavy
Current Regulations, Section 107-2-D1, Standard Sheet
DKA 1-3 for portable socket-outlets. Shutters are not
required.
To the third paragraph the following is added:
Mains socket-outlets with earthing contact shall be in
compliance with Heavy Current Regulations Section 107-2D1, Standard sheet DK 1-3a, DK 1-5a or DK 1-7a
Justification:
Heavy Current Regulations, Section 107
Report reference No.: WT093001905
Page 25 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
15.1.1
S(NO)
Result - Remark
Verdict
No socket-outlets
N
Mains socket-outlets mounted on CLASS II apparatus shall
comply with the specifications given in CEE Publ. 7 as far as
applicable, with the following amendments:
§ 8 Dimensions
a 2,5 A 250 V two-pole socket-outlets for electronic
apparatus shall comply with the enclosed Standard Sheet I.
§ 24 Mechanical strength
a 2,5 A, 250 V socket-outlets for CLASS II electronic
apparatus are tested as specified in 12.1.3 of EN 60065.
Also the protecting rim shall be tested
Justification:
Act of 24 May 1929 relating to supervision of electrical
installation (TEA 1929/FEL 1998).
15.2
C: Delete note 2.
N
16.1
C: Delete note 1.
N
16.2
C: Delete the note.
N
20
C: Delete note 2.
N
Annex B
C: Replace not 1 by:
N
In the CENELEC countries listed in IEC 62151, special
national conditons apply.
Add the following:
All subclauses given below are subclauses of IEC 62151
Report reference No.: WT093001905
Page 26 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
(ref. corrigenda 1 and 2 to IEC 62151).
Subclause 4.1.1 (corrigendum 2):
Add after the first paragraph:
NOTE In Finland, Norway and Sweden, CLASS I equipment
which is intended for connection to the building installation
via a non-industrial plug or a non-industrial appliance
coupler, or both and in addition is intended for connection to
other equipment or a network shall, if safety relies on
connection to protective earth or if surge suppressors are
connected between the network terminals and
ACCESSIBLE parts, has a marking stating that the
equipment must be connected to an earthed mains socketoutlet.
The marking text in the applicable countries shall be as
follows:
In Finland: “Laite on liitettävä suojamaadoituskoskettimilla
varustettuun pistorasiaan”
In Norway: “Apparatet må tilkoples jordet stikkontakt”
In Sweden: "Apparaten skall anslutas till jordat uttag"
Subclause 4.1.4 (corrrigendum 1)
Add at the end of the subclause:
NOTE In Norway, for requirements see 4.1.1, note and
5.3.1, note 1.
Subclause 4.2.1.2 (corrigendum 1)
Add at the end of the subclause:
NOTE 3 In Norway, for requirements see 5.3.1, note 1.
Subclause 4.2.1.3 (corrigendum 2)
Add at the end of the subclause:
NOTE In Norway, for requirements see 4.1.1, note and
5.3.1, note 1.
Subclause 4.2.1.4 (corrigendum 1)
Number the existing note as NOTE 1 and add at the end of
the subclause the following NOTE 2:
NOTE 2 In Norway, for requirements see 4.1.1, note and
5.3.1, note 1.
Subclause 5.3.1 (corrigendum 1)
Add after the first test specifications paragraph:
NOTE 1 In Finland, Norway and Sweden, there are
additional requirements for the insulation.
Renumber the existing note as NOTE 2.
Report reference No.: WT093001905
Page 27 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
For additional requirements for the insulation in Finland,
Norway and Sweden in NOTE 1 the following text is added
between the first and the second paragraph (this text is
identical to the corresponding EN 60950-1:2001):
NOTE 1 In Finland, Norway and Sweden, if this insulation is
solid, including insulation forming part of a component, it
shall at least consist of either
• two layers of thin sheet material, each of which shall pass
the electric strength test below, or
• one layer having a distance through insulation of at least
0,4 mm, which shall pass the electric strength test below
If this insulation forms part of a semiconductor component
(e.g. an optocoupler), there is no distance through insulation
requirement for the insulation consisting of an insulating
compound completely filling the casing, so that
CLEARANCES and CREEPAGE DISTANCES do not exist,
if the component passes the electric strength test in the
accordance with the compliance clause below and in
addition:
• passes the test and inspection criteria of 13.6 with an
electric strength test of 10.3 using the test voltage of 1,5 kV
multiplied by 1,6, and
• is subject to routine testing for electric strength during
manufacturing, using a test voltage of 1,5 kV (for
performance of the test see N.2.1).
It is permitted to bridge this insulation with a capacitor
complying with EN 132400:1994, subclass Y2.
A capacitor classified Y3 according to EN 132400:1994, may
bridge this insulation under the following conditions:
• the insulation requirements are satisfied by having a
capacitor classified Y3 as defined by EN 132400, which in
addition to the Y3 testing, is tested with an impulse test of
2,5 kV defined in IEC 62151, Subclause 6.2.1;
• the additional testing shall be performed on all the test
specimens as described in EN 132400;
• the impulse test of 2,5 kV is to be performed before the
endurance test in EN 132400 in the sequence of tests as
described in EN 132400.
Subclause 5.3.2 (corrigendum 1)
Add after the fourth dash:
NOTE In Finland, Norway and Sweden, exclusions are
applicable for equipment which is intended for connection to
the building installation wiring using screw terminals or other
reliable means, and for equipment which is intended for
Report reference No.: WT093001905
Page 28 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
connection to the building installation wiring via an industrial
plug and socket -outlet or an appliance coupler, or both,
complying with EN 60309 or with a comparable national
standard.
S(SE)
N
14 The following is added:
Switches containing mercury such as thermostats, relays
and level controllers are not allowed.
Justification:
Ordinance (1990:944) on Prohibition in Connection with
Handling, Importation and Exportation of Chemical Products
(Certain Cases)
Annex G
C: Delete the note
N
Annex J.2
C: Delete the notes of Table J.1.
N
J.2
After Table J.1 the following is added:
N
In Norway, due to the IT power distribution system used, the
a.c. MAINS supply voltage is considered to be equal to the
line-to-line voltage, and will remain 230 V in case of a single
earth fault.
Justification:
Based on a use in Norway of an IT power distribution
system where the neutral is not provided
Annex N
C: Add after the introduction:
N
For ROUTINE TEST reference is made to EN 50333.
Bibliograph
y
C: Add the following standards:
P
EN 50332-1: 2000, Sound system equipment: Headphones
and earphones associated with portable audio equipmentMaximum sound pressure level measurement methodology
and limit considerations- Part 1: General method for “one
package equipment”.
EN 50332-2:2003, Sound system equiment: Headphones
and earphones associated with portable audio equipemntMaximum sound pressure level measurement method and
limit considerations-Part 1: General method for “one
package equipemnt”.
EN 50332-1: 2003, Sound system equipment: headphones
and earphones associated with portable audio equipmentMaximum sound pressure level measruement- Maximum
sound pressure level measurement methodology and limit
consideration- Part 2: Matching of sets with headphones if
either or both are offered separately
EN 60065:2002/A1:2006
Add the following notes for the standards indicated:
Report reference No.: WT093001905
Page 29 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Result - Remark
Verdict
IEC 60130 (all parts) NOTE: Parts 9 and 17:1998 are
harmonized as ENs (not modified).
IEC 60169 (all parts) NOTE: Partly harmonized in the EN
60169/HD 134 series (not modified).
IEC 60173:1964 NOTE: Harmonized as HD 27 S1:1978 (not
modified).
IEC 60335-2-56:1997 NOTE: Harmonized as EN 60335-256:1997 (not modified).
IEC 60335-2-82:1999 NOTE: Harmonized as EN 60335-282:2000 (not modified).
IEC 60410:1973 NOTE: Harmonized as EN 61040:1992 (not
modified).
IEC 60695 (all parts) NOTE: Harmonized as EN 60695
series (not modified).
IEC 61040:1990 NOTE: Harmonized as EN 61040: 1992
(not modified)
IEC 61558-2-1:1997 NOTE: Harmonized as EN 61558-21:1997 (not modified).
IEC 61558-2-4:1997 NOTE: Harmonized as EN 61558-24:1997 (not modified).
IEC 61558-2-6:1997 NOTE: Harmonized as EN 61558-26:1997 (not modified).
IEC 61558-2-9: NOTE: Hamonized as EN 60598-29:1989+A1:1994 (not modified)
IEC 61558-2-17 NOTE: Harmonized as EN 60598-2-17:
1989+A2:1991 (not modidied).
Annex ZA
P
C: other international plublications quoted in this standard
with the reference of the relevant European publications
This European Standard incorporateds by dated or undated
referenece. For dated references, subsequent amendments
to or revisions of any of these publications apply to this
European Standard only when iincorporated in it by
amendment or revision. For undated references the lasted
edition of the publication refered to applies (including
amendments).
NOTE When an international standard has been modified by
common modification, indicated by (mod), the relevant
EN/HD applies.
Report reference No.: WT093001905
Page 30 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Report reference No.: WT093001905
Result - Remark
Verdict
Page 31 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Report reference No.: WT093001905
Result - Remark
Verdict
Page 32 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Report reference No.: WT093001905
Result - Remark
Verdict
Page 33 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Report reference No.: WT093001905
Result - Remark
Verdict
Page 34 of 49
EN 60065:2002+A1: 2006
Clause
Requirement – Test
Report reference No.: WT093001905
Result - Remark
Verdict
Page 35 of 49
7.1
TABLE: temperature rise measurements
P
Power consumption in the OFF/Stand-by
2.43W
--
Position of the functional switch (W) ...................... : --
—
Operating conditions
Normal working
Un (V)
In (mA)
Pn (W)
Pout(W)
198V/50Hz
63.2
6.17
--
220V/50Hz
61.5
6.30
--
240V/50Hz
69.2
6.44
--
264V/50Hz
56.0
6.63
--
198V/60Hz
63.3
6.16
--
220V/60Hz
63.0
6.29
--
240V/60Hz
71.3
6.29
--
264V/60Hz
56.4
6.66
--
Loudspeaker impedance (Ω) ............ --
—
Several loudspeaker systems
--
--
Marking of loudspeaker terminals
--
Monitored point:
dT (K)
Limit dT (K)
198V/50Hz
264V/50Hz
Power cord insulation
15.0
14.0
60
Connector CN6
16.6
15.5
For reference
X2 cap C15
17.9
17.0
65
LF1 coil
21.9
21.2
75
PCB near D17
32.3
35.3
85
E-cap C123
34.7
38.2
70
PCB near U9
55.5
68.1
85
T1 coil
41.8
44.8
75
T1 bobbin
40.1
43.2
For reference
PCB near D19
36.3
36.3
85
Optocoupler U10
34.4
36.6
65
Y-cap C133
34.9
37.5
70
PCB near U3
38.7
36.6
85
Top enclosure (metal)
11.3
10.2
40
Front enclosure (plastic)
7.7
6.3
60
Key
6.2
4.3
50
Report reference No.: WT093001905
Page 36 of 49
Operating conditions
Winding temperature rise measurements
N
o
Ambient temperature t1 ( C) .................................. : 24.1(198V), 24.3(264V)
—
Ambient temperature t2 (oC) .................................. : 24.4(198V), 25.3(264V)
—
Temperature rise dT of winding:
R1 (Ω)
R2 (Ω)
dT (K)
Limit dT (K)
Insulation
class
Note:
7.2
TABLE: softening temperature of thermoplastics
Temperature T of part
9.1.1
N
T - normal conditions (oC)
T - fault conditions (oC)
T softening
(oC)
TABLE: Electric shock hazard under normal condition
Measured between:
P
U1 (V)
Required U1
(Vpk)
U2 (V)
Required U2
(Vpk)
L/N and metal enclosure
0.190
35
0.168
0.35
L/N and signal terminal
0.196
35
0.172
0.35
10.3
TABLE: insulation resistance measurements
P
Insulation resistance R between:
R (MΩ)
Required R (MΩ)
L and N (fuse open)
>100
≥2
L/N and signal terminal
>100
≥4
Primary and secondary coil of the T1
>100
≥4
Secondary coil and the core of the T1
>100
≥4
10.3
TABLE: electric strength measurements
Test voltage applied between:
P
Test voltage (V)
Breakdown
L and N (switch open)
1500
No
L/N and signal terminal
3000
No
Primary and secondary coil of the T1
3000
No
Secondary coil and the core of the T1
3000
No
Report reference No.: WT093001905
Page 37 of 49
11.2
TABLE: summary of fault condition tests
P
Voltage (V) 0,9 or 1,1 times rated voltage ............. :
See below
—
Ambient temperature (oC) ...................................... :
25 oC-27 oC
—
fault condition, state component short- or open
circuited and components whose temperature
rises are measured
supply
voltage
result, state effect of fault condition and the
duration of the test
264V/50Hz
Work until got steady state. No excessive
temperature rise. No hazard. Test last for 2h
264V/50Hz
Overload to 0.3A, input current: 76mA, input
power: 8.62W. Work until got steady state. No
excessive temperature rise. No hazard. Test
last for 1.5h
264V/50Hz
Input current: 55mA, input power: 6.17W.
Work until got steady state. No excessive
temperature rise. No hazard. Test last for 2h
E45 short circuit
264V/50Hz
Input current: 22-46mA, input power: 0.191.23W. Circuit protected. Unit shut down
immediately. No hazard. Test last for 15min
D19 short circuit
264V/50Hz
Input current: 22mA, input power: 0.32W.
Circuit protected. Unit shut down immediately.
No hazard. Test last for 15min
U10 pin3-4 short circuit
264V/50Hz
Input current: 22mA, input power: 0.29W.
Circuit protected. Unit shut down immediately.
No hazard. Test last for 15min
U10 pin1-2 short circuit
264V/50Hz
Input current: 22-41mA, input power: 0.321.27W. Circuit protected. Unit shut down
immediately. No hazard. Test last for 15min
U9 pin1-8 short circuit
264V/50Hz
Fuse opened immediately. Fuse current:
2.4A.
U9 pin1-8 short circuit
198V/50Hz
Fuse opened immediately. Fuse current:
2.6A.
C123 short circuit
264V/50Hz
Fuse opened immediately. Fuse current:
2.4A.
C123 short circuit
198V/50Hz
Fuse opened immediately. Fuse current:
2.6A.
Opening block
Transformer T1 coil: 52.2K
PCB: 75.4K
Enclosure (metal): 17.3K
Enclosure (plastic): 13.2K
USB overload
Transformer T1 coil: 52.5K
PCB: 85.2K
Enclosure (metal): 13.6K
Enclosure (plastic): 9.1K
USB short circuit
Transformer T1 coil: 40.6K
PCB: 64.3K
Enclosure (metal): 9.8K
Enclosure (plastic): 5.6K
Report reference No.: WT093001905
Page 38 of 49
D14 short circuit
264V/50Hz
Fuse opened immediately. Fuse current:
2.5A.
D14 short circuit
198V/50Hz
Fuse opened immediately. Fuse current:
2.5A.
Winding temperature rise measurements
N
o
Ambient temperature t1 ( C) .................................. :
--
—
Ambient temperature t2 (oC) .................................. :
--
—
Note(s): -Clause 13.3
Clause 13.4
TABLE: Creepage distance and clearance
Rated supply voltage:
220-240V
Pollution degree:
P
II
Material Group:
IIIb
30 N force on outside of conductive enclosure applied.......................:
Applied
30 N force on outside of conductive enclosure applied.......................:
Applied
Locations between:
Operating voltage
Clearance (mm)
Creepage (mm)
CTI
V peak
V rms
Min
Actual
Min
Actual
< 175
L and N (before the fuse)
339
240
2.0
4.2
2.5
4.2
< 175
L and N (under the fuse)
339
240
2.0
3.0
2.5
3.0
< 175
PCB trace between primary and
secondary circuit under T1
460
240
4.2
6.8
4.8
6.8
< 175
PCB trace between primary and
secondary circuit under U10
436
240
4.2
7.2
4.8
7.2
< 175
PCB trace between primary and
secondary circuit under C48
339
240
4.0
7.1
4.8
7.1
< 175
Primary and secondary of the T1
460
240
4.2
>6.0
4.8
>6.0
< 175
Core and secondary of the T1
460
240
4.2
4.6
4.8
>5.0
< 175
Transformer core and secondary of
C133
460
240
4.2
>4.4
4.8
>5.0
< 175
Primary and metal enclosure
339
240
4.0
7.0
4.8
8.0
< 175
Notes:
1. Secondary circuits of Class II apparatus which have connector terminals that could be earthed (e.g. antenna signal
input), are subjected to the requirements for circuits conductively connected to the mains in Tables 8 and 9.
2. Floating secondary circuits of Class I apparatus which have connector terminals that could be earthed (e.g. antenna
signal input), are subjected to the requirements for circuits conductively connected to the mains in Tables 8 and 9 unless
the floating secondary circuit is separated from the primary circuits by an earthed metal screen (e.g. in the power
transformer), or the floating secondary circuit is connected to earth via a component such as a capacitor.
3. For insufficient clearances and creepage distances from secondary to secondary circuits and from secondary circuits to
earth, see Cl.
4.3.1, 4.3.2 and 11.2.
4. If the minimum creepage distance in Table 11 is less than the minimum required clearance in Tables 8, 9 or 10 as
required, then the value for clearance is used as the minimum creepage distance.
"Min" = minimum required.
"Actual = Actual dimensions measured.
Report reference No.: WT093001905
Page 39 of 49
Report reference No.: WT093001905
Page 40 of 49
14
TABLE: list of critical components and materials
Component
Manufacturer/
Type/model
Value / rating
P
Standard
trademark
Approval/
Reference
Shenzhen
H03VVH2-F
Baohing Electric
Wire & Cable
Manufacture Co.,
Ltd.
2×0.5mm2
VDE 0281-5
VDE 103727
Ching Cheng
Wire Material
Co., Ltd.
EL-207
2.5A 250V
VDE 0620
VDE
40002990
(alt.)
Shenzhen Hong
Yun
HYP-201
2.5A/250V~
VDE 0620
VDE
40021944
Power cord
Phino Electric
Co., Ltd
H03VVH2-F
2×0.75mm2
VDE 0281-5
VDE 113841
Phino Electric
PHP-318
Company Limited
250V~, 13A
BS 1363: Part
1+A1+A2
KM 69214
Fuse in BS plug
Dongguan
Cooper
Electrionics Co.,
Limited
TDC 180
240V~, 3A
BS
1362+A1+A2
ASTA 658
(alt.)
Taller GmbH
ATLAS
240V~, 3A
BS
1362+A1+A2
KM70570
Connector (CN6)
Zhejiang Jinda
Electronics Co.,
Ltd
--
VH-3A2-7.8MM
UL 1977
UL E237523
X2 capacitor
(C15 & C49)
Tenta Electric
MEX
Industrial Co.,Ltd
IEC 60384-14
VDE 119119
(alt.)
Shenzhen
Shengxin
Capacitor Co.,
Ltd.
IEC 60384-14
VDE 123934
MEX-X2
0.1uF/280VAC
Y1 capacitor
(C31, C48 &
C33)
Hsuan Tai
Electronics
Co.,Ltd
1000pF, 400VAC,
Y1
IEC 60384-14
VDE118413
CY
1000pF, 400VAC,
Y1
IEC 60384-14
VDE118413
(alt.)
Shantou HighNew
Technology
CD
Dev. Zone
Songtian
Enterprise Co.,
Ltd.
XC
3T
Electronics(Shen
zhen) Corp Ltd
T630mA L250V
EN 60127-1
VDE
40019614
Power cord
(EU)
Power plug
(EU)
(BS)
Power plug
(BS)
Fuse
Report reference No.: WT093001905
0.1uF/275VAC
EN 60127-2
Page 41 of 49
Line filter (LF1)
Hua Yu Electrical UU9.8
Factory
85mH
EN 60065
Test in unit
Transformer T1
Hua Yu Electrical EE25
Factory
Class B
EN 60065
Test in unit
-Primary Wire
TAI-I ELECTRIC
WIRE & CABLE
CO LTD
UEW
130℃
UL 1446
UL E85640
-Bobbin
Chang Chun
Plastic Co., Ltd
T375J
150℃, V-0
UL 94
UL E59481
(alt.)
Various
Various
150℃, V-0
UL 94
UL
-Insulation tape
JINGJIANG
YAHUA
PRESSURE
SENSITIVE
GLUE CO LTD
CT280
130℃
UL 510
UL E165111
(alt.)
Various
Various
130℃
UL 510
UL
-Tube
Changyuan
Electronics
(Shenzhen) Co
Ltd
CB-TT-T
600V, 200℃
UL 224
UL E180908
-Triple insulated
wire
SHANGHAI
CHUANYE
ELECTRONIC
TECHNOLOGY
CO LTD
GPX-B
130℃
UL 60950-1
UL E243712
Optocoupler U10
Bright LED
Electronics Corp
BPC-817B
Reinforce
insulation
EN 60747-5-2
VDE
40007240
(alt.)
Sharp Corp
Electronics
Components
Group
Xing Da Printed
Circuit Board Mfr
Various
PC817
Reinforce
insulation
EN 60747-5-2
VDE
40008087
XD-105
V-0, 130℃
UL 94
UL E193079
Various
V-0, 130℃
UL 94
UL
Plastic enclosure
HB
UL 94
UL E162823
Heat
tube
300V, 125℃
UL 224
UL E180908
300V, 125℃
UL 224
UL
PCB
(alt.)
(alt.)
Formosa
AG15A1
Chemicals
&
Fibre
Corp
Plastics Div
shrinkable CHANGYUAN
CB-HFT
ELECTRONICS
(SHENZHEN) CO
LTD
Various
Various
Report reference No.: WT093001905
Page 42 of 49
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement