1 Parallel, 2 USB User`s Manual

1 Parallel, 2 USB User`s Manual
Wireless 802.11g Print Server
1 Parallel, 2 USB
User’s Manual
Rev. 01 (APR, 2004)
Made In Taiwan
TABLE OF C ONTENTS
ABOUT THIS GUIDE .................................................................................. 4
1. INTRODUCTION..................................................................................... 5
PACKAGE CONTENTS .................................................................................... 6
SYSTEM REQUIREMENTS ............................................................................... 6
GENERAL FEATURES ..................................................................................... 7
PRODUCT VIEW............................................................................................. 8
2. HARDWARE INSTALLATION ........................................................... 10
NETWORKING APPLICATION ....................................................................... 10
INSTALLING THE PRINT SERVER .................................................................. 11
3. USING THE UTILITIES ....................................................................... 12
AUTO-RUN INSTALLATION ......................................................................... 12
PS-UTILITY ................................................................................................. 14
Installing PS-Utility ................................................................................ 14
Using PS-Utility...................................................................................... 15
PS WIZARD ................................................................................................. 18
4. PRINTING IN MAC OS ........................................................................ 21
RENDEZVOUS USES IN MAC OS 10.2 ......................................................... 21
SETTING UP APPLE TALK/LPR PRINTING ................................................... 24
For MAC OS X User............................................................................... 24
For MAC OS 9 User ............................................................................... 27
-2-
5. WEB CONFIGURATION ......................................................................30
WEB CONFIGURATION UTILITY ...................................................................30
MANAGEMENT.............................................................................................31
Management J System ...........................................................................33
Management J Wireless.........................................................................33
Management J Network .........................................................................35
Management J User...............................................................................37
CONFIGURATION..........................................................................................38
Configuration J System..........................................................................38
Configuration J Wireless .......................................................................40
Configuration J Network .......................................................................42
Configuration J User .............................................................................44
Configuration J E-mail ..........................................................................45
Configuration J SNMP ..........................................................................47
TOOLS .........................................................................................................48
Tool J Print Test ....................................................................................48
Tool J E-mail .........................................................................................49
Tool J Reset ...........................................................................................50
Tool J Factory Reset..............................................................................51
Tool J Firmware Upgrade .....................................................................52
Tool J Backup ........................................................................................53
HELP............................................................................................................54
6. PRODUCT SPECIFICATIONS.............................................................55
-3-
A BOUT THIS G UIDE
This manual provides instructions and illustrations on how to use your
Wireless Print Server, including:
z
Chapter 1, Introduction, provides the general information on the
product.
z
Chapter 2, Hardware Installation, describes the hardware
installation procedure for the product.
z
Chapter 3, Using the Utilities, helps you to install and use the
software.
z
Chapter 4, Printing in MAC OS, lets you complete printing task
through your print server in MAC OS environment.
z
Chapter 5, Web Configuration, completes the configuration using
the web browser.
z
Chapter 6, Product Specification.
Please note that the illustrations or setting values in this manual are FOR
YOUR REFERENCE ONLY. The actual settings and values depend
on your system and network. If you are not sure about the respective
information, please ask your network administrator or MIS staff for help.
-4-
1
I NTRODUCTION
Congratulations on purchasing your Wireless Print Server, the easiest and
fastest way to deploy printers on your network.
This compact print server can connect your network through an Access
Point under the infrastructure mode, or can be used in ad-hoc mode for
direct communication between PC/Notebook and print server anywhere
you wish to locate wireless printer services. It manages the flow of print
files from your workstation or file server to its connected printers,
delivering print jobs to high-performance printers much faster than a file
server or a PC acting as a print server can.
The Wireless Print Server features a Web-based Configuration Utility,
which allows you to set up the print server through the web browser
easily and quickly. It also includes a powerful software utility PSUtility, a user-friendly program that allows you to complete further
settings for the print server.
-5-
Package Contents
Unpack the package and check all the items carefully, and be certain that
you have:
♦ One Wireless Print Server.
♦ One AC Power Adapter suitable for your country’s electric power
service.
♦ One Quick Installation Guide.
♦ One Installation CD-ROM containing the PS-Utility program and the
User’s Guide.
If any item contained is damaged or missing, please contact your local
dealer immediately. Also, keep the box and packing materials in case
you need to ship the unit in the future.
System Requirements
♦ Operating System:
Microsoft Windows 95/98/ME/NT/2000/XP/2003.
Apple Mac OS (with Apple Talk support).
♦ For Web Configuration:
Java-enabled web browser, such as Microsoft® Internet Explorer
5.0 and Netscape Navigator 6.0.
-6-
General Features
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
Equipped with 1 parallel port and 2 USB ports allows user to share
three printers on LAN simultaneously
Compliant with USB 2.0 Hi-speed printing
Equipped one 10/100 auto-MDIX Fast Ethernet LAN port
Multi protocol support is ideal for shared printing in mixed-LAN
environments
Windows-based administrative program makes it possible to set up in a
few minutes.
Latest MIB-II (RFC 1213) for SNMP standard management
Offer LPR program for Windows 95/98/Me TCP/IP printing
IP assignment support for DHCP, BOOTP and RARP
Support Web configuration
Provide Flash memory for easy firmware upgrade
Highly efficient design mechanism to provide unbeatable performance
achieving data rate up to 54Mbps for 802.11g and 11Mbps for 802.11b
with wide range coverage
Printing Access control and display
E-mail notification for printer error messages
Support E-Mail printing and FTP printing
Ability to save print server configuration into hard drive for easy
access and backup without the hassle to reconfigure if setting is altered
Support IPP for Windows 2000/XP
Support second http port for remote web configuration and IPP
printing.
Support UPnP(Universal Plug and Play) for Windows XP
Support Mac 10.2 “Rendezvous” zero-configuration function
-7-
Product View
This section describes the externally visible features of the print server.
Front View
LEDs*
Rear View
LPT Port – connect the print
server to a LPT printer.
LAN Connector –
plug your LAN cable
to this connector.
USB Port – connect the print
server to a USB printer.
-8-
DC Power Input –
plug the AC Power
Adapter to this jack.
Reset Button**
* There are six green LED indicators on the front panel:
LEDs
Description
Power
Steady light confirms that the Print Server is
powered on.
USB1
When it blinks, the printer connected is printing.
USB2
When it blinks, the printer connected is printing.
LPT
When it blinks, the printer connected is printing.
LAN
Steady light confirms that the print server has a
good connection to your network.
When it blinks (briefly dark), the print server is
receiving/ transmitting data from/to the network.
WLAN
Steady light confirms that the print server has a
good connection to your wireless network.
When it blinks (briefly dark), the print server is
receiving/ transmitting data from/to the wireless
network.
** 1) Press and release this button to reset the print server; or 2) Press
and hold this button for three seconds (the USB LED on the front panel
lights up) and then release it, the print server will resume the factory
default settings.
-9-
2
H ARDWARE
I NSTALLATION
Networking Application
The following diagram explains the application of your print server.
Wireless Print Server
- 10 -
Installing the Print Server
Follow these steps for a trouble-free start of print server operations with
your Wireless Print Server.
1. Confirm proper operation of the printer to be connected to the print
server.
2. When you have confirmed proper operation of the printer, turn off the
power.
3. Confirm that your network is operating normally.
4. Connect the print server to the network (through the RJ-45 connector
of the print server).
5. While the printer is powered off, connect the print server to the
printer’s USB or Parallel port.
6. Turn on the printer’s power.
7. Connect the DC end of the AC Power adapter to the DC power input
socket of the print server and the AC end to the wall outlet. This will
supply power to the print server immediately.
NOTE: This print server is built with a default IP Address. To prevent
from any conflict in your network, it is recommended to use the PSUtility program to change the IP setting when there is some other
device’s IP Address is the same as the print server’s default IP
Address.
- 11 -
3
U SING T HE U TILITIES
This chapter describes the software utilities for the print server, including
how to set up your print server with these utility. The PS-Utility and
PS Wizard are designed with a user-friendly interface that allows you to
set up and administer the print server easily.
Auto-Run Installation
Insert the Installation CD-ROM into your computer’s CD-ROM drive to
initiate the Auto-Run program, and the menu screen will appear as below.
- 12 -
• User's Guide – click to preview the User's Guide in PDF format for
detailed information of the Wireless Print Server.
• Install Utility – click to install PS-Utility. Please refer to the next
section for detailed information on installing the utility.
• PS Wizard – click to launch the Printer Wizard program, which is
helpful to set up the printer configuration easily and quickly.
• Browse CD – if you want to browse the contents of the Installation
CD-ROM, click this button and the contents of the CD will be
available for preview.
• Exit – click to close the Auto-Run program.
- 13 -
PS-Utility
To avoid the conflict in your network, you can use PS-Utility to change
the related settings of your print server (such as the IP address) after
finishing the installation.
Installing PS-Utility
1. Click Install Utility from the Auto-Run menu screen. Once
executed, the Setup program will extract files to launch the
InstallShield Wizard; then, click Next > in the welcome screen of
InstallShield Wizard.
2. Choose the destination location. If no specific requirement, leave
the default setting and click Next >.
- 14 -
3. The InstallShield Wizard starts to install the software, and the
Progress bar indicates the installation is proceeding.
4. When completed, click Finish.
After installing the utility, the application program for the print server is
automatically installed to your computer, and creates a folder in
Start\Programs\PS-Utility.
Using PS-Utility
This section describes the operation of PS-Utility.
To launch PS-Utility:
1. Click Start -> Programs -> PS-Utility, and then click the PS-Utility
v2.00 item.
- 15 -
2. The main screen will appear as below, and it starts to search the
connected print server within the network.
Your print server
Component Features:
1. Device List: Display the connected print server within the network.
2. Control Buttons
- Change IP Address: Click
this button to bring up the
following dialog box,
allowing you to change the
IP Address. In this dialog
box, you can select either
Manually Assign or DHCP
Assign Automatically.
When completed, click OK.
- Update Firmware: Click this button to update the firmware of
the selected print server.
- 16 -
-
-
Show Web Setup: Click this button to open your web browser
and launch the Configuration Utility. Alternately, you can
double-click the print server in the Device List to launch the
Configuration Utility.
Factory Reset: Click this button to reload the factory settings of
the print server.
Discover Device: Click this button to search the connected print
server again.
About: Click this button to bring up a window containing the
basic information of PS-Utility.
Close: Click this button to exit PS-Utility.
3. Information Field: Display the basic information of the selected
print server in the Device List.
4. Status Bar: Display the system status.
- 17 -
PS Wizard
PS Wizard is a convenient utility that allows you to set up the print
server’s port connection.
To launch PS Wizard:
1. Insert the Installation CD-ROM into your computer’s CD-ROM
drive, and click PS Wizard from the Auto-Run menu screen. The
welcome screen appears as below. Click Next >.
NOTE: For some specific printers, you may need to connect the
printer to the computer and install the driver. In this case, connect it
to the computer and install the driver first, and then connect it to the
print server.
- 18 -
2. In the following window, select one printer in the Printer List to set
up port connection, and then click Next >.
Choose one connected
printer within the network.
3. Select one printer port in the Print Server List, and click Next >.
Your print server name
Your printer port name
- 19 -
Choose one connected
printer port.
4. The configuration is completed, click Finish and then Yes to restart
the system.
After rebooting, PS Wizard will help you to complete the port
connection automatically. You can start your printing task without
any complex configuration.
TIP: If you use Windows 2000/XP, the system will not restart to
complete the installation.
- 20 -
4
P RINTING IN MAC OS
Rendezvous Uses in MAC OS 10.2
The latest version of MAC OS provides a new feature that is called
Rendezvous. Rendezvous is a revolutionary networking technology
standard that lets you create an instant network of computers and devices,
which can be used throughout Mac OS 10.2 to provide innovative ways
to share files and printers and even contact other people on the network.
For the printer connection, the Mac OS 10.2 Print Center application uses
Rendezvous to discover Rendezvous-enabled printers on the network.
When you add your computer to a network, Print Center automatically
discovers the available printers. All you have to do is selecting the one
you want to use and then start printing. You can add a new printer to
the network and all the users on the network will see the new printer
automatically appear in their Print Center, without any configuration.
The following instructions provide a common procedure of installing the
printer:
- 21 -
1. Launch Print Center.
button.
Press and hold the Option key, click the Add
2. Select Rendezvous from the pop-up menu.
3. When clicking the Rendezvous item, the following window appears
to display the connected Rendezvous-enabled printers.
Connected printer(s)
- 22 -
4. Select the desired printer, and the following pop-up menu displays
the printer’s manufacturer. Select Generic.
5. The printer is installed into the system successfully.
- 23 -
Setting Up Apple Talk/LPR Printing
For MAC OS X User
With MAC OS X, you can use AppleTalk or LPR printers to print
through the print server. Follow the instructions below for setting up
the print server:
1. After attaching the print server to your network, change the IP
Address of your Macintosh computer to access the print server’s web
configuration. The default IP Address of the print server is
192.168.0.1. Change your IP Address to 102.168.0.x, where x is
any number between 2 and 254.
2. Open the System Preference window and click Network. In the
Network window, select the AppleTalk tab and check the Make
AppleTalk Active option.
Check this option.
- 24 -
3. To print, open a document and select File > Print from the menu.
Select this option.
4. Select Edit Printer List from the Printer dialog box.
Select this option.
5. Click Add Printer. Then, select the desired printing protocol
(AppleTalk or LPR Printers using IP).
- 25 -
- AppleTalk: After selecting AppleTalk, the Port Name of the print
server will be displayed. Select the Port to which the post-script
printer is connected. Then, select the printer model from the
dialog box. Click Add Printer to complete the Printer Port
configuration. Select the Printer Port just configured in the
Print window. Click Print to print your document.
- LPR Printers using IP: When you select LPR Printers using IP
Protocol, type the IP Address of the print server into the LPR
Printer’s Address field of the following window. In the Queue
Name field, type in the Port Name of the post-script printer that
is connected to the Print Server. Select the printer model from
the dialog box, and select the printer model from the pull-down
menu. Click Add to complete the process. Close all Print
Center windows and select the Printer Port that was just selected.
Then, click Print to print the document.
Port Name of the connected printer.
- 26 -
For MAC OS 9 User
If you use MAC OS 9, you can use the AppleTalk network protocol for
network communications over standard Ethernet or Fast Ethernet using
the EtherTalk transport, or over a proprietary low-speed LocalTalk
transport. Your print server can be used for network printing to
PostScript printers. You can print from any MAC OS computer
connected to your Ethernet network, either directly using an EtherTalk
connection or indirectly through a LocalTalk-to-EtherTalk router.
To set up the print server to be used for AppleTalk printing:
1. Please confirm that the AppleTalk protocol is enabled in your
Macintosh computer.
2. Change the IP Address on one of the computers within your network
to 192.168.0.x (where x is any number between 2-254).
3. Type 192.168.0.1 (the default IP Address) into the address field of
your browser.
4. Select the Network tab and scroll to the AppleTalk protocol section.
5. If your AppleTalk network is divided into AppleTalk zones, you
have to specify which zone the Print Server should be in. You
should locate the print server in the same zone as most of the users
who will be using it. If your network is not divided into zones, it
should contain a single asterisk “*”.
- 27 -
To print from MAC OS Client Workstations:
The actual settings of selecting a PostScript printer connected to your
print server may be different from the instructions provided in this
section, depending on the devices and the software you are using.
1. To choose a printer connected to your print server as your MAC OS
workstation’s default printer, select Chooser from the Apple menu.
2. In the left column of Chooser window, select the desired item.
Please confirm that AppleTalk is set to Active. A list of all
networked PostScript printers will be displayed within the right
column.
Select
Check this option.
3. Double-click the name of the Printer Port you wish to use.
Printer Ports shown are examples only.
- 28 -
The
4. If you have not previously set this printer as the default, your
computer will prompt you for a PostScript Printer Description file.
Choose Select PPD.
5. Select the appropriate printer description file for your printer. Click
Open. (If your printer is not listed, click Generic to use a generic
printer description.)
The selected printer will become your computer’s default printer. You
may need to choose Page Setup in any applications you have open.
- 29 -
5
W EB C ONFIGURATION
You can access and manage the Wireless Print Server through: 1) the
enclosed software PS-Utility, and 2) a web browser. This chapter
describes the second method – the Web Configuration Utility, and
explains how to set up your print server with the web browser.
Web Configuration Utility
First, launch your web browser (such as the Internet Explorer 6.0 used in
this manual). Then, type http://192.168.0.1 (the default IP address) in
the Address bar and press [Enter] to enter the Management screen of the
Configuration Utility.
TIP: The computer’s IP address must correspond with the print
server’s IP address in the same segment for the two devices to
communicate.
Extensive knowledge of LAN will be helpful in
configuring the print server.
- 30 -
Management
- 31 -
The Management Screen of the Configuration Utility
The Management screen displays the basic information of the print
server, including the following four categories:
z System
z Wireless
z Network
z User
- 32 -
Management J System
As shown above, the System displays the status of your print server,
printer, and network. Clicking Refresh will update the information.
Device Status
The information about the print server, including the firmware version,
MAC/IP address, and up time, can be found in this field.
Printer Status
The items in this field display the information of the printer, such as the
given name for the printer, speed, printer status, and status of your
printing tasks, etc.
Ethernet Status
You can monitor the networking status in this field, including the
network connection, speed, and the packets status.
Management J Wireless
Click the Wireless item in the left column to display the information of
the wireless LAN. Clicking Refresh will update the information.
- 33 -
Wireless Status
The items in this field display the information of the wireless LAN, such
as the connection mode (Infrastructure or Ad-Hoc), SSID, channel, data
transfer rate, WEP encryption, and the packets status.
- 34 -
Management J Network
Click the Network item to display the information of the LAN. Clicking
Refresh will update the information.
- 35 -
Auto IP
This field contains the current settings of TCP/IP, including
DHCP/BOOTP, UPnP, and MAC Rendezvous. The items in this field
are configured in Configuration > Network > TCP/IP.
TCP/IP Printing
In this field, you can monitor the status of your printing tasks through
TCP/IP.
Microsoft Network Printing
In this field, you can monitor the status of your printing tasks through
Microsoft Network.
MAC AppleTalk Printing
In this field, you can monitor the status of your printing tasks through
MAC AppleTalk.
- 36 -
Management J User
Click the User item in the left column to display the user(s) information.
Users Printing Log
The items in this field display the user(s) information, which include the
user(s) MAC address, IP address, name, and status of printing tasks.
- 37 -
Configuration
Configuration J System
System Device
In this field, you can configure the basic information of your print server.
-
Server Name: Assign a name to the print server.
Location (optional): Assign a location for the print server
Admin Contact (optional): Assign the Admin Contact’s name for
the print server.
- 38 -
-
Password: Enter the Administrator password (3-8 characters). To
set up the password, please enter the password in the New Password
box, and then enter the same one again in the Confirm Again box.
Port Settings
In this field, you can assign the Port Name for the print server, and the
description for the USB port. It also allows you to select the PJL
Printer setting (Yes or No).
NOTE: PJL (Print Job Language) has certain job requirements that
must be met to work correctly. For more information, please refer to
your printer’s manual.
- 39 -
Configuration J Wireless
Wireless Interface
-
-
Connection Mode: Select one of the three connection modes.
• Infrastructure (default) - Connects to compatibly configured
wireless AP or router in a WLAN.
• Ad-Hoc - Connect to compatibly configured wireless clients in
the peer-to-peer mode.
SSID: Assign the SSID in this box. You can manually input the
name or select one from the pull-down menu. To search the
available wireless AP within the network, click the Site Survey
button.
- 40 -
-
Wireless Channel: Select the channel from the pull-down menu.
The default setting is 11.
Transmission Rate: Select the data transmit rate from the pull-down
menu. The default setting is Fully Automatic.
WEP Encryption
This field allows you to configure the settings of data encryption.
Please remember that the WEP key must be set before the data encryption
is enforced.
-
WEP Encryption: This option allows you to select Disable, 64 bits,
and 128 bits for the encryption setting.
WEP Key Format: You can decide the network key to be encoded
by ASCII (ASCII characters) or HEX (hexadecimal digitals).
Then, enter the key(s) for the network in the Key box (1~4).
Advanced Setting
This field allows you to configure more settings, including:
- Beacon Interval: Enter the number of beacon interval time in
millisecond.
- Preamble: This option allows you to set the length of preamble.
Setting options are: Long - it is set to 144 bits; Short - it is set to 72
bits.
- Authentication Type: You can set the authentication type by
selecting the settings: Open System, Shared Key, and Both.
TIP: Once you have changed the settings in each option, click Save
to store the settings, or Cancel to abandon.
- 41 -
Configuration J Network
- 42 -
TCP/IP
This field contains three options that allow you to configure the TCP/IP
setting: IP Address, UPnP, and MAC Rendezvous.
-
-
IP Address: This option allows you to set the IP address manually or
automatically. When you choose Manually Assign, you should
enter the related information in the following boxes, including IP
Address, Subnet Mask, and Default Gateway.
UPnP: This option allows you to enable or disable UPnP mode.
MAC Rendezvous: This option allows you to enable or disable
MAC Rendezvous mode.
Microsoft Network
Enter the name of the Workgroup that you want the print server
associated with in this field.
AppleTalk
Enter the AppleTalk Zone name in the box. In the following options,
enter the related configuration, such as the printer type.
-
USB1,USB2,LPT3
• Chooser Name: Display the print server’s Port name.
• Printer Type: Enter the printer’s type in this box.
• PostScript Level: Select from the pull-down menu (Level 1 or
Level 2).
• Font Group: Select from the pull-down menu.
TIP: Once you have changed the settings in each option, click Save
to store the settings, or Cancel to abandon.
- 43 -
Configuration J User
Printing Control
By configuring the Enable User Printing Control option (Yes or No),
the user in the User List is permitted to access the print server or not.
For the user(s) who is not in the User List, you can also limit the access
right by setting the Allow Undefined Users Printing option to Yes or
No.
Define Users
You can add/delete the user(s) to/from the User List. The User List at
the bottom of the screen displays the current defined user and related
information for the print server.
TIP: Once you have changed the settings in each option, click Save
to store the settings, or Cancel to abandon.
- 44 -
Configuration J E-mail
E-mail Account
You can assign an E-mail address to the print server, so that your mail of
the account can be printed out directly through the printer (ASCII text
only). To enable this function, enter the E-mail account in the Print
Server E-mail Address box.
-
Incoming E-mail (POP3) Server Address: Enter the server address
that is used to receive your E-mail in this box.
Outgoing E-mail (SMTP) Server Address: Enter the server address
that is used to send your E-mail in this box.
If your mail server needs to verify the user when sending E-mail, you
have to input the Account Name and Password.
- 45 -
E-mail Notification
You can set the print server to send an alter message when the printer
status changes through E-mail. To enable this function, set the Enable
e-mail notification for printer status changing option to Yes. Then,
input the administrator’s E-mail address in the Admin E-mail Address
box.
E-mail Printing
-
E-mail Printing (ASCII Text Only): Select Enable to enable the Email printing function.
Receive E-mail Interval: Enter the number in this box to set up the
time (in minute) to check/receive E-mail regularly.
TIP: Once you have changed the settings in each option, click Save
to store the settings, or Cancel to abandon.
- 46 -
Configuration J SNMP
SNMP Management
SNMP (Simple Network Management Protocol) is a set of protocols for
managing complex networks
-
Community 1/2/3: Enter a name in the Name box, and configure the
Access Right by selecting Read Only or Read/Write from the pulldown menu.
TIP: Once you have changed the settings in each option, click Save
to store the settings, or Cancel to abandon.
- 47 -
Tools
Tool J Print Test
Print Test
Choose one of the print ports and Click Test to print a test page.
- 48 -
Tool J E-mail
Test E-mail Account
Click Test to send a test E-mail to the given administrator’s E-mail
address.
Receive E-mail
Click Yes to immediately check and receive E-mail, and then print out
the mail when available.
- 49 -
Tool J Reset
Reset
Click Yes to immediately reset the print server.
- 50 -
Tool J Factory Reset
Factory Reset
Click Yes to reload the factory settings of the print server.
- 51 -
Tool J Firmware Upgrade
Firmware Upgrade
When a new version of firmware is available (e.g. downloading from the
manufacturer’s website), you can upgrade the firmware of your print
server. Click Browse to point to the firmware file, and then click
Upgrade.
- 52 -
Tool J Backup
Backup Device Configuration to File
Click Backup to backup your current configuration of the print server to
file and then save in the computer.
Restore Device Configuration from File
You can reload a configuration that you saved before.
point to the backup file, and then click Restore.
- 53 -
Click Browse to
Help
This screen displays the information of the print server.
- 54 -
6
P RODUCT
S PECIFICATIONS
Printer Connection
Printer Interface: Two USB port, compliant with USB 2.0 Hi-speed
standard.
Network Connection
Wireless Networking
Network Standards: Wireless LAN standard IEEE802.11g.
Network Data Transfer Rate: 54Mbps with fallback to 48, 36, 24, 18,
12, 11, 9, 6, 5.5, 2, and 1Mbps.
Network Mode: Support both Infrastructure and Ad-hoc mode.
Wired Networking
Network Interface: One 10/100 Fast Ethernet port (RJ-45 connector).
Network Data Transfer Rate: 100Mbps.
- 55 -
Network Protocol Support
Transport Protocols: TCP/IP, SMB, NetBEUI, and AppleTalk.
TCP/IP Protocols Support: BOOTP, SNMP, Telnet, FTP, LPD, DHCP,
and IPP.
Hardware
SDRAM: 8MB.
Flash ROM: 2MB.
Operating System Support
- Windows 95/98/ME, Windows NT, Windows 2000/XP/2003;
- NetWare 5.x (NDPS LPR remote printing);
- HP-UX Unix, Sun O.S, Solaris, SCO Unix, AIX;
- Unixware and Linux;
- Mac OS, AppleTalk.
Management
Standard: SNMP
MIBs: MIB-II (RFC 1213).
Utilities: PS-Utility, PS Wizard.
- 56 -
LEDs
Power, LAN, WLAN, USB1 ,USB2, LPT
Environmental and Physical
Power Supply: 5VDC.
Operating Temperature: 0°C to 50°C.
Storage Temperature: -25°C to 55°C.
Humidity: 5% to 95%, non-condensing at 30°C.
EMI Compliance
FCC Class B, CE Class B, VCCI Class B
- 57 -
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement