Mitsubishi WD-65731 DLP Television Owner's Manual

Add to my manuals
100 Pages

advertisement

Mitsubishi WD-65731 DLP Television Owner's Manual | Manualzz
DIBITAL
TELEVISIONS"
DLP TM PROJECTION TELEVISION
MODELS
WD-52631
WD-57731
WD-65731
OWNER'S GUIDE
•
For questions:
Call Consumer Relations at 800-332-2119.
E-mail us at [email protected].
Visit our website at www.mitsubishitv.com.
•
For information on Demo Mode and System
Reset, please see the back cover.
•
To order replacement or additional remote
controls, lamp cartridges, or Owner's Guides,
visit our website at www.mitsuparts.com
or
call 800-553-7278.
Guidelines for setting up and using your new
widescreen TV start on page 13.
ViBwPOifll
QN SCR EN or>FHA
IG SYS_M
HIGH
DEFINHTION
MULTIMEDIA
INTERFACE
RISK OF ELECTRIC SHOCK
DO NOT OPEN
•
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the
presence of uninsulated "dangerous voltage" within the product's enclosure that may be sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
RAIN OR MOISTURE.
FCC Declaration
Product:
Projection
Models:
WD-52631,
Responsible
Telephone:
Party:
Television
TO
of Conformity
Receiver
WD-57731,
WD-65731
Mitsubishi Digital Electronics
9351 Jeronimo Road
Irvine, CA 92618-1904
America,
Inc.
(800) 332-2119
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
Changes or modifications
not expressly approved by Mitsubishi
void the user's authority to operate this equipment.
could cause harmful interference
and would
J
Our Thanks...
Thank you for choosing
Mitsubishi
as your premier
Home Entertainment
provider
This Owner's Guide describes the features and functions of your Mitsubishi
widescreen, high definition TV. We urge you to examine this Owner's Guide to
become familiar with the innovative features and operations this unique television
offers.
The very core of our corporate philosophy is to provide our customers with the
very best. Our development team at Mitsubishi has worked to provide you with
a television that defines "state=of-the=art," with the capability to meet your needs
now and in the future.
Whether this is your first Mitsubishi electronic product, or an addition to your
Mitsubishi collection, we believe you and your family will continue to enjoy your
Mitsubishi home theater for many years.
Thank you,
Mitsubishi
Digital Electronics
America,
Inc.
For Your Records
Record the model number, serial number, and purchase date of your TV. The model and serial numbers are on the
back of the TV. Refer to this page when requesting assistance with this TV.
MODEL NUMBER (check one}:
[_
SERIAL NUMBER
PURCHASE DATE
Retailer information
RETAILER NAME
LOCATION
WD-52631
[_
WD=57731
_
WD=65731
Contents
Important
information
About
Your TV
General Warnings and Cautions, Notes on Installation and Operation
Cleaning Recommendations
...........................
............................................................
Important Safeguards ..................................................................
Chapter
1: Television
6
7
8
Overview
Package Contents ....................................................................
12
Special Features of Your TV ............................................................
12
Guidelines for Setting Up and Using Your New Widescreen TV ................................
TV Front Panel
13
Control Panel ....................................................................
System Reset Button ...........................................................
A!V Reset ....................................................................
15
15
15
Input 3 ..........................................................................
Front-Panel Indicators .............................................................
15
16
CableCARD TM Technology .............................................................
TV Back Panel .......................................................................
17
18
Chapter
2:
TV Connections
Before You Begin
Choosing a Language for Menus .....................................................
22
ClearThought®
22
Easy Connect Auto Input Sensing .......................................
Digital Video and Home Recording ...................................................
23
Connection Types .................................................................
24
HDTV Cable Box or Satellite Receiver with Component Video ................................
25
Standard Cable Box, Satellite Receiver, or Other Device with S-Video ..........................
25
Wall Outlet Cable (no cable box) ........................................................
26
Antenna with a Single Lead ............................................................
27
Antennas with Separate UHF and VHF Leads ..............................................
27
VCR to an Antenna or Wall Outlet Cable ..................................................
28
VCR to a Cable Box (Audio & Video) .....................................................
29
HDMI Device (Cable Box, Satellite Receiver, DVD Player, or Other Device) ............................
30
DVI Video Device (Cable Box, Satellite Receiver, DVD Player, or Other Device) ...................
30
DVD Player with Component
31
Video ......................................................
A/V Receiver (Stereo System) ..........................................................
31
Older Cable Box .....................................................................
32
Camcorder ..........................................................................
32
Chapter
3:
TV Operation
Remote Control ......................................................................
34
Choosing a Program Source ...........................................................
36
ChannelView
36
TM
Channel Listings ........................................................
Status Display .......................................................................
37
TV Signals and Display Formats ........................................................
38
Split Screen .........................................................................
40
Chapter
4:
TV Menu Settings
3D Graphical !_VlBWPOiAI
® Menu System ....................................................
44
MainMenu..........................................................................
SetupMenu.........................................................................
InputNameMenu....................................................................
IconOrderMenu.....................................................................
ChannelMenu.......................................................................
CaptionsMenu......................................................................
ParentalLockMenu..................................................................
Settinga PassCode...............................................................
LockTVbyTimeandFront-Panel
Lock...............................................
RatingMenus....................................................................
Bypassing
the RatingsLockandLockbyTime.........................................
V-ChipSignalInformation
TVRatings
.......................................................................
MovieRatings....................................................................
Audio/VideoMenu...................................................................
AudioSettings...................................................................
VideoSettings....................................................................
Chapter
5: Operating
Other Devices
with
the Remote
45
46
48
48
49
51
53
53
53
53
55
56
56
57
58
59
Control
Functions Available for Other A/V Devices ................................................
62
Programming the Remote Control .......................................................
63
Programming
64
Chapter
Codes ..................................................................
6: Using
the TV with a Personal
Computer
Setup ..............................................................................
74
Video Adjustments
...................................................................
74
a Computer to the TV .......................................................
75
Connecting
Adjusting Image Resolution ............................................................
77
Computer Display Formats .............................................................
78
Chapter
7: Using IEEE 1394 Devices
Overview ...........................................................................
80
Recording to IEEE 1394 Recordable Devices ..............................................
82
The TV Remote Control and IEEE 1394 Devices ............................................
84
A/V Discs ...........................................................................
85
Switching Between Analog and Digital IEEE 1394 Outputs
...................................
86
Appendices
Appendix
A: Bypassing the Parental Lock ................................................
89
Appendix
B: Specifications
91
Appendix
C: Lamp Cartridge Replacement ...............................................
93
Appendix
D: Troubleshooting
95
............................................................
..........................................................
Trademark
and License
Information
Mitsubishi
TV Software
................................................................
Mitsubishi
DLP
Index
TM
Projection
...................................................
Television
Limited
...................................................................................
Warranty ..............................
101
102
103
105
6
important
information
About
Your TV
WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects or
other reproductive harm.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
TV WEIGHT: This TV is heavy! Exercise extreme care when lifting or moving it. Lift or move the TV with a minimum
of two adults. To prevent damage to the TV, avoid jarring or moving it while it is turned on. Always power off your TV
before moving it.
installation
Stand
Notes
Requirement
CAUTION: Use these Mitsubishi TV models only with the
Mitsubishi stand models shown here. Other stands can
result in instability and possibly cause injury.
Custom cabinet installation
must allow for proper air circulation around the television.
NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S
ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR THE PROPER GROUNDING AND,
IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF
THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL.
Operating
Standby
Notes
Fan
When the TV is off, you may hear a low-power standby
fan. This is normal operation. The fan cools advanced
circuitry in this TV that must continue to operate even
when the TV is turned off.
Demo
Mode
This TV has a demo mode for use in retail stores. To turn
off demo mode:
1.
Press MENU.
2.
When the Main menu appears with Setup highlighted,
press ENTER.
3.
When the Setup menu opens, press _ to highlight the
on-screen Demo Mode Off button.
4.
Press ENTER.
Lamp Replacement
The image on this TV is produced by a powerful lamp
that will operate for many hours. Eventually, however, this
lamp will need to be replaced. Order a new lamp when
you notice the TV image becoming dimmer.
Replace
the lamp yourself and save the cost of a service call.
Please see Appendix C for details on lamp replacement.
To Receive a Replacement
Lamp Under Warranty
serial number, and TV purchase date available.
553-7278.
Order lamp part number 915P049010.
important
Cleaning
information
About
Your TV
7
TV Software
Recommendations
Normally, light dusting with a dry, non-scratching duster
will keep your TV clean. If cleaning beyond this is needed,
please use the following guidelines:
Unauthorized
Software
Top and Sides of the TV
Do not attempt to update the software of this TV with
software or cards that are not provided by or authorized
by Mitsubishi Digital Electronics America, Inc. Non-authorized software may damage the TV and will not be covered
by the warranty.
•
Software
First, turn off the TV and unplug the power cord from the
power outlet.
Gently wipe down your TV with a soft, non-abrasive
cloth such as cotton flannel or a clean cloth diaper,
lightly moistened with water. Dry with a second dry,
soft, non-abrasive cloth.
For oily dirt, add a few drops of mild liquid detergent,
such as dishwashing detergent, to the water used to
moisten the cloth. Rinse with a second cloth moistened only with water. Dry with a third dry, soft, nonabrasive cloth.
Screen
•
Follow the instructions for the top and sides, wiping
gently in an up and down motion, following the
grooves in the screen.
Clean the entire screen evenly, not just sections of the
screen.
Do not allow liquid to drip down the grooves of the
screen, as some liquid may enter the TV through the
gap between the screen and screen frame.
You may purchase Mitsubishi Screen Cleaner, part
number CLEANER-VSS, by calling (800) 553-7278.
General
Cleaning
Warnings
DO NOT allow liquid to enter the TV through the ventilation slots or any crevice.
DO NOT use any strong or abrasive cleaners, as these
can scratch the surfaces.
DO NOT use any cleaners containing ammonia,
bleach, alcohol, benzene, or thinners, as these can
dull the surfaces.
DO NOT spray liquids or cleaners directly on the TV's
surfaces.
DO NOT scrub or rub the TV harshly. Wipe it gently.
___of
abrasive
face
of the TV screen.
cleaner
Updates
From time to time, Mitsubishi may offer software updates
to expand the features or operation of this TV. When
these updates are available they will be announced on our
web site, Mitsubishi-tv.com.
If you return your owner's
registration card, with your model and serial number,
you may receive written notification of available software
updates.
8
important
information
About
Your TV
Important Safeguards
Please read the following safeguards for your TV and retain for future reference.
tions marked on the television.
Always follow all warnings and instruc-
1.
Read, Retain and Follow All instructions
Read all safety and operating instructions before operating the TV. Retain the safety and operating instructions
for future reference. Follow all operating and use instructions.
2.
Heed Warnings
Adhere to all warnings on the appliance and in the operating instructions.
3.
Cleaning
Unplug the TV from the wall outlet before cleaning. Do not use liquid, abrasive or aerosol cleaners.
can permanently damage the cabinet and screen. Use a lightly dampened cloth for cleaning.
4.
5.
Attachments
and Equipment
Never add any attachments and/or equipment without approval of the manufacturer
result in the risk of fire, electric shock or other personal injury.
Water
as such additions may
and Moisture
Do not use the TV where contact with or immersion in water is possible.
bowls, kitchen sinks, laundry tubs, swimming pools, etc.
6.
Cleaners
Do not use near bath tubs, wash
Accessories
Do not place the TV on an unstable cart, stand, tripod, or table. The TV may fall,
causing serious injury to a child or adult and serious damage to the TV. Use only with a
cart, stand, tripod, bracket or table recommended by the manufacturer, or sold with the
TV. Any mounting of the TV should follow the manufacturer's instructions, and should
use mounting accessories recommended by the manufacturer.
An appliance and cart combination should be moved with care. Quick stops, excessive
force, and uneven surfaces may cause the appliance and cart combination to overturn.
=
=
Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the TV and to
protect it from overheating. Do not block these openings or allow them to be obstructed by placing the TV on
a bed, sofa, rug, or other similar surface. Nor should it be placed over a radiator or heat register. If the TV is to
be placed in a rack or bookcase, ensure that there is adequate ventilation and that the manufacturer's instructions have been adhered to.
Power Source
This TV should be operated only from the type of power source indicated on the marking label. If you are not
sure of the type of power supplied to your home, consult your appliance dealer or local power company.
g=
Grounding
or Polarization
This TV is equipped with a polarized alternating current line plug having one blade wider than the other. This
plug will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the polarized plug.
10. Power=Cord
Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the TV.
11. Lightning
For added protection for this TV during a lightning storm, or when it is left unattended and unused for long
period of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent
damage to the TV due to lightning and power-line surges.
important
Important Safeguards,
12. Power
information
About
Your TV
9
continued
Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or circuits as contact with them might be
fatal.
13. OveHoading
Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
14. Object and Liquid Entry
Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or
short-out parts that could result in fire or electric shock. Never spill liquid of any kind on or into the TV.
15. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the TV, be sure
the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.
EXAMPLE
OF
ANTENNA
GROUNDING
LEAD
GROUND
CLAMP
IN WIRE
ANTENNA
ANTENNA
DISCHARGE
Article 810 of the National Electric Code, ANSI/NFPA No. 70-2002,
provides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead in wire to an antenna
discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements
for the grounding electrode.
UNIT
GROUNDING
CONDUCTORS
(NEC
ARTICLE
OUND
CLAMPS
(NEC ARTICLE
810 21)
810
20)
POWER SERVICE
GROUNDING
ELECTRODE
SYSTEM
NEC
NATIONAL
E LECTRICAL
CODE
(NEC
ART
250,
PART
H/
16. Servicing
Do not attempt to service this TV yourself as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
17. Damage Requiring
Service
Unplug the TV from the wall outlet and refer servicing to qualified service personnel under the following conditions:
(a)
(b)
(c)
(d)
When the power-supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen into the TV.
If the TV has been exposed to rain or water.
If the TV does not operate normally by following the operating instructions, adjust only those controls that
are covered by the operating instructions as an improper adjustment of other controls may result in damage
and will often require extensive work by a qualified technician to restore the TV to its normal operation.
(e) If the TV has been dropped or the cabinet has been damaged.
(f) When the TV exhibits a distinct change in performance - this indicates a need for service.
18. Replacement
Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by
the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in
fire, electric shock or other hazards.
19. Safety Check
Upon completion of any service or repair to the TV, ask the service technician to perform safety checks to
determine that the TV is in safe operating condition.
20. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves or other products (including amplifiers) that produce heat.
Television Overview
Package Contents
..................................
Special Features of Your TV ............................
Guidelines for Setting Up and Using Your New Widescreen
TV Front Panel
Control
Panel
.....................................
input 3 .........................................
Front-Panel
indicators ................................
CabieCARD TM Technology .............................
TV Back Panel .....................................
TV . ..
12
12
13
15
15
16
17
18
12
Chapter
1. Television
Overview
Package Contents
1.
Remote Control
Please take a moment to review the following list of items to ensure
that you have received everything.
2.
Two AA Batteries
3.
Product registration
4.
Owner's
5.
Quick Reference
card (not pictured)
Guide (not pictured)
Guide (not pictured)
Special Features of Your TV
Your new high-definition widescreen television has many special features that make it the perfect center of your home
entertainment system, including:
High Definition
DLP
TM
Display System
Your widescreen Mitsubishi HDTV uses Texas Instruments most advanced Digital Light Processing TM technology for
rear-projection televisions. This TV is truly a high-performance multimedia monitor uniquely capable of both stunning
high-definition video images and clear, detailed, high-resolution images from a personal computer.
16:9 Widescreen
Picture
Format
Enjoy a full theatrical experience in the comfort of your home. View pictures as film directors
broadcasts, DVDs and newer video game consoles support this widescreen format.
integrated
intended them. Digital TV
HDTV Tuner
Your widescreen
Mitsubishi HDTV has an internal HDTV tuner able to receive both over-the-air
(received via an antenna) and non-scrambled
ming.
High=Definition
digital cable broadcasts,
including non-scrambled
HDTV broadcasts
HDTV cable program-
Video inputs
0
Two Component Video Inputs, also called Y/Pb/Pr inputs. These inputs receive standard analog video formats of
480i, 480p, 720p, 1080i, and 1080p high-definition signals. This provides a high level of flexibility when connecting
DVD players/recorders, cable boxes, and satellite receivers.
0
Two HDMI Inputs that accept digital 480i, 480p, 720p, 1080i, and 1080p video signals plus PCM digital stereo
signals. Used with an adapter, these inputs also accept compatible DVl video signals. HDMI inputs provide additional high-performance,
high-definition connections for maximum flexibility in your choice of home theater products. The HDMI inputs are HDCP copy-protection compatible.
0
Two iEEE 1394 Digital interfaces that receive and send compressed digital signals, including high-definition
signals, along with digital audio and control signals between devices such as the TV, digital cable boxes, and
D-VHS digital video recorders.
ClearThought®
Easy Connect
Auto input
Sensing
ClearThought® automatically recognizes when you plug in an input and prompts you to assign a name to it. The TV
ignores any unused inputs, so the result is an uncluttered Input Selection menu where you can easily find and select
connected devices by name.
Chapter
Digital Cable
Ready
(CableCARDTM),
Models
WD=57731
1. Television
Overview
13
and 65731
Your widescreen Mitsubishi HDTV is "Plug-and-Play" digital cable ready. It can descramble a cable provider's one-way
digital signals with the use of a CableCARD security module. The CableCARD is used in place of a traditional cable box
to access digital cable programming (including high definition). Contact your local cable provider for availability information and service details.
Guidelines for Setting Up and Using
Your New Widescreen TV
See "Setup
tings,"
Started
Read the section entitled "important
About Your TV" starting on page 5.
1.
2.
information
Choose a location for your TV.
•
Additional
Install the batteries in the remote control.
2.
Review chapter 4, "TV Menu Settings," to customize TV operation. Press the MENU
key to enter the menu
system. Some examples of settings you may wish to
change include:
Energy Mode. For
Energy Mode set to
power consumption
Low Power setting.
See
chapter 3, "TV Operation," for information on use
and care of the remote control.
4.
Plug your TV into a power outlet. The POWER
indicator
on the front of the TV will start blinking rapidly. After
the POWER
indicator stops blinking, press the POWER
key
to power on the TV.
5.
When the Welcome screen appears the first time you
power on the TV, select a language for TV menus.
You can later change the language through the Setup
menu.
.
active when you first turn on the TV:
a. Press MENU.
c.
d.
7.
8.
=
Icon Order. Rearrange the device icons in the
Input Selection menu to put frequently used icons
near the front. See "Icon Order Menu."
•
FAV. Create lists of your favorite channels so you
can find them quickly. See "Channel Menu."
=
Clock. If you wish to schedule future recordings
or use the Timer feature to have the TV come on
automatically, you must first set the TV clock to
the correct time. See "Setup Menu."
Parental Lock. You can restrict TV viewing by
program rating or by time of day. You can also
disable the front-panel buttons--useful if you have
small children. See "Parental Lock Menu."
When the Main menu appears with Setup highlighted, press ENTER.
When the Setup menu opens, press I_ to highlight
the on-screen Demo Mode Off button.
Press ENTER.
Video Settings.
Change the video adjustments
to get the best picture for your viewing conditions.
See "Audio/Video
Menu."
Connect your other A/V devices to the TV and assign
device names to the TV inputs when prompted.
See chapter 2, "TV Connections,"
for connection
diagrams. You can reassign device names later if
needed. See "input Name Menu" in chapter 4, "TV
Menu Settings."
Memorize channels if you plan to watch over-the-air
channels or programming over direct cable. Channel
memorization may take up to 15 minutes to complete.
faster power-on, keep the
Fast Power On. For lower
while the TV is off, use the
See "Setup Menu."
Input Name. Change the device names that
appear in the Input Selection menu. See "Input
Name Menu."
Some TVs are shipped from the factory with demo
mode active for use in retail stores. If demo mode is
b.
TV Setup
To program the remote control to operate your other
A/V devices, see chapter 5, "Operating Other
Devices with the Remote Control."
See the stand requirements under "Important
information About Your TV."
.
4, "TV Menu Set=
1.
Allow at least four inches of space on all sides of
the TV to help prevent overheating.
Avoid locations where light may reflect off the
screen.
in chapter
You can now start watching TV or you can perform
additional setup and customization through the TV
menus.
g.
Getting
Menu"
You may wish to change the Picture Mode from
the default Brilliant to either Bright or Natural,
which are suitable for most home viewing environments.
.
If you have IEEE 1394 A/V devices, see chapter 7,
"Using IEEE 1394 Devices," for details on operating
such devices and using the TV to control recording.
14
Chapter
1. Television
Overview
Guidelines for Setting Up and Using
Your New Widescreen TV, continued
TV Operation
Review chapter
including:
•
•
3, "TV Operation,"
for TV features
Input Selection (viewing source). Select a connected program source to watch, such as a VCR,
DVD player, or antenna. Press INPUT
on the remote
control to select from icons for the TV inputs. See
"input Selection Menu."
Channel Listings. Press GUIDE
to view
ChannelView TM channel listings. See
"ChannelView TM Channel Guide."
Picture Formats. Press FORMAT
to cycle through
the available picture sizes and shapes to find the
one best suited to the program you're watching.
See "TV Signals and Display Formats."
•
SPLIT. Press SPLIT
to view two programs at the
same time. See "Split Screen Mode."
TV Care
Caring for your TV:
Lamp Cartridge.
When the lamp cartridge needs
replacement, replace the lamp yourself and
save the cost of a service call. See Appendix
C for instructions.
General Cleaning. To keep your TV looking its
best, see the cleaning recommendations under
"Important
information About Your TV."
Assistance
If you need assistance with this TV:
For troubleshooting,
see Appendix D.
service, and product support,
For warranty information, see the TV warranty in
the back of this book.
Chapter
1. Television
Overview
15
TV Front Panel
s
\
Control
Panel
iNPUT 3
The shaded buttons on the front control panel duplicate keys on the remote control. The upper labels show
control functions when no TV menus are displayed;
the lower labels indicate functions when TV menus are
;-VIDEO
VIDE()
@
@
displayed or when a special function has been activated.
See "Remote Control Overview" in chapter 3, "TV Operation," for further details on the functions of these buttons.
System
Reset Button
If the TV does not respond to the
remote control, front panel controls,
or will not power on/off, press the
SYSTEM
RESET
button on the front panel
with a pointed object, such as the point
of a pencil or end tip of a paperclip.
The green LED will flash quickly for
about one minute. When the green LED stops flashing,
you may turn on the TV. The changes you made most
recently, before using SYSTEM
RESET,
may be lost. Changes
you made previously, however, are not lost.
A/V Reset
If you wish to reset the A!V (Audio/Video)
the factory defaults:
•
Above and Below:
1.
Shaded buttons are duplicates
remote control
of keys on the
2.
POWER/TIMER indicator--lit during normal
operation; flashing when auto-on TV Timer is set
3.
LAMP indicator shows lamp condition (usually
off during normal TV operation)
4.
STATUS indicator (off during normal TV operation)
5.
SYSTEM RESET (see description
this page)
settings back to
To reset all settings at once, press GUIDE
and FORMAT
on
the front panel at the same time.
Lift cover to use
the control panel
and INPUT3 front
A/V jacks.
To reset the defaults for individual devices, use the
A/V Memory Reset selection on the Audio/Video
menu.
input 3
iNPUT 3 provides an easily accessible set of standard
audio/video jacks. These jacks allow for convenient connection of a camcorder or other audio/video device. Note
that if you connect to the S=VIDEO
jack is deactivated.
VIDEO
jack, the VIDEO
L-AUDIO-R
@ @
I
N
P
U
T
3
iNPUT
3 and controls on front panel of WD-57731 and WD-65731
I_
STATUES
@
16
Chapter
Front=Panel
indicators
O Off
LAMP
Green
1. Television
O Steady On
Overview
qD Slow Blinking
(_ Fast Blinking
Indicator
_
TV just powered off and lamp is
cooling,
Starts to blink 30 seconds after turning off TV. TV can be turned
on before blinking starts or after blinking stops, but not while the
indicator is blinking. Normal operation.
Ye"ow
_ i: Eamp
ac_es_
doo;isopenoi .........
T_wiiinoiop_;aie
uni"ia_pac_ssdo_;issecuie:
Se_Appen:
2.
not secure,
dix C for installation
No namp nnstalleu.
......
_lon ,n_orma[_on.
information.
"
.................................................................................................
reached!h endo!!h !am#!!!e:
.........................................
!onge ! um!Pa!e Se A#Pend
! C1o!np!a!!a!!£
!P[trm
a!!£...............
STATUS Indicator
None
O
Normal TV on or standby condition.
Yellow
O
_oom temperature
Red
_
_D
TV may require service.
, ,
s too n gn
Normal operation.
TV w not operate when the amb ent room temperature s too
hugh. Turn off the TV and want until the room temperature drops.
Turn off the TV and unplug the set from the AC power source.
Wait one minute and then plug the set back in.
If the LED is still on, contact your dealer or a Mitsubishi Authorized
Service Center. See www.mitsubishi-tv.com
or call 1-800-3322119 to receive Authorized Service Center information.
POWER/TIMER
Green
_)
1.
Indicator
TVjust
plugged into AC outlet.
restored after power ........................................
failure.
Reset used.
4.
TV Rebooting after power
fluctuation or receiving abnormal digital signals from digital
channel, CableCARD TM, or
Wait until blinking stops before turning on (approximately
minute). Normal operation.
1
.............................
digital device _
5.
You have begun the procedure
to update software from an
authorized flash memory device,
For detailed information, see the instructions that accompany the
authorized software update. Important: Do not use unauthorized
software at any time.
:_
Chapter
CableCARD
TM
1. Television
Overview
17
Technology
(models WD=57731 and WD-65731)
CabieCARD
TM
Menu
CableCARD is a nationwide system standard that allows
your local cable TV provider to supply you with an access
card customized to your account. This card allows your
TV to receive, decode, and unscramble the premium
digital channels included in your cable TV subscription
without the use of a cable box. When you move to a
new cable provider's area, return the CableCARD to the
original cable provider and get a new card from your new
provider.
Please note that CableCARD is a relatively new technology
and your local cable provider may not currently be offering this service. As time passes, this system will become
broadly supported by most cable providers.
The CableCARD system is unidirectional, meaning your
cable provider can send updates to the TV, but the TV
cannot send signals back. As a result, certain advanced
and interactive digital cable services, such as requests for
video-on-demand
and pay-per-view programs, a cable
operator's enhanced program guide, and data-enhanced
television services may require use of a set-top box
instead. For more information, call your local cable operator.
Sample CableCARD menu
To display the CableCARD menu with links to applications
from your cable provider:
1.
While watching CableCARD, press INPUT
to open the
Input Selection menu.
2.
With the CableCARD icon highlighted, press MENU
to
open the CableCARD menu.
3.
Press A Y to highlight a link (blue text), then press
ENTER
to access the linked page.
4.
Digital cable channels authorized by the CableCARD are
available on the Firewire® IEEE 1394 network and can be
To redisplay the CableCARD menu, repeat steps 1 and
2.
5.
Press EXITto return to TV viewing.
shared by other products on the network. You may be
unable to record or copy some digital programs, however,
because of copy restrictions set by the content or copyright owners.
If there are technical problems with the CableCARD, an
error screen automatically displays with information that
may be needed by your cable provider when you call them
for assistance.
Using
a CabieCARD
TM
Power on the TV and insert the CabieCARD into the
CableCARD slot with the top of the card oriented as indicated by CARD TOP A. When the initial screen displays, write down the information that appears and have it
ready when calling your cable provider.
Moving Through Other CableCARD
In addition
application
additional
Mitsubishi
•
Screens
to CableCARD menus, other CableCARD
screens may display and require you to make
selections. When using these screens on your
television:
Blue text denotes a link to another screen. Press ENTER
to move to the next application. Screens without blue
text contain no links.
You cannot move backward through the links. To exit
the CableCARD system, press EXIT.The CANCEL
key may
not work with some CableCARD screens.
All information on these application screens is provided by
your local cable company. Contact your cable provider if
you have any problems with the application screen displays.
Sample CableCARD initial screen. Record the information
before contacting your cable provider.
To review the information later, press MENU
and when the
Main menu appears, press 9 9 9 to re-display the screen.
Note:
CableCARD TM requires the TV's Fast Power On
setting. If you insert a CableCARD TM, the TV will
automatically override a Low Power setting and
change to the Fast Power On setting.
18
Chapter
1. Television
Overview
TV Back Panel
ANT2 / AUX
@@
ANT1 I MAIN
H :3m|
HDMI
COMPATIBILITY
VIDEO:
480V480c
720cJ1080i/1
OS0c
/
ANT 1
on WD-52631
ANT 1/MAIN
1. ANT l/MAIN,
ANT 2/AUX
(Antenna)
If you are connecting an antenna, direct cable without
a cable box, or are using cable with a CableCARD TM,
connect the main antenna or cable source to
ANT l/MAIN.
ANT 1/iVlAIN and ANT 2/AUX can each receive both
digital and analog over-the-air channels from a VHF/UHF
antenna or non-scrambled digital/analog cable source.
ANT l/MAIN
WD-65731)
and CableCARD
TM
2. CabieCARD
TM
Slot
(models WD=57731 and WD=65731)
The CableCARD access card from your cable TV service
provider is inserted into this slot. When inserting, ensure
that the top of the card faces in the direction indicated by
CARD TOP A.
If your cable company is not currently offering CableCARD
access cards, use the cable box provided and authorized
by your local cable company to view scrambled channels.
(models WD=57731 and
Use ANT l/MAIN
to receive premium subscription cable
TV service authorized by the CableCARD TM access card.
The CableCARD access card is provided by your local
cable company. ANT 2/AUX can continue to receive
over-the-air or non-scrambled cable signals when ANT 1
is used for CableCARD TM service.
3. iNPUT 1 and 2 inputs
(Audio and Video)
iNPUT 1 and 2 can be used to connect a VCR, Super
VHS (S-VHS) VCR, DVD player, standard satellite receiver,
or other A/V device to the TV. INPUT 3 is a third set
of jacks located on or near the front of the TV for convenience. Please note that if S=VIDEO and VIDEO are
both available, you must choose to connect only one.
Chapter
1. Television
Overview
TV Back Panel, continued
8. PC=DVI AUDIO
4. COMPONENT
Use the PC=DVI AUDIO jacks in conjunction with the
PC=DVl video input from a personal computer. These
jacks allow you to send left and right analog audio from
your computer to the TV.
1 and 2 inputs
(Audio and Video)
Y Pb Pr (480i/480p/720p/1080i)
Use these jacks to connect devices with component video
outputs, such as DVD players, external HDTV receivers, or
compatible video game systems. Please see Appendix B
for signal compatibility.
5. HDMF M 1 and 2
The HDMI (High Definition Multimedia Interface) supports
uncompressed standard and high-definition digital video
formats and PCM digital audio format. For PC video, use
the PC=DVl input instead.
Do not connect
a computer
to either TV HDMI jack.
Use these inputs to connect to EIA/CEA-861 compliant
devices such as a high-definition receiver or DVD player.
These inputs support 480i, 480p, 720p, 1080i, and 1080p
video formats.
These inputs can also accept DVl video inputs. To connect
a DVl input, use an HDMI-to-DVl adapter or cable plus
analog audio cables. Connect the analog audio cables to
the HDMI/DVl
AUDIO inputs on the TV to receive left
and right stereo audio from your DVl device.
These inputs are HDCP (High-Bandwidth
tection compliant.
Digital Copy Pro-
9. DTVLINKTM/IEEE
6. HDMI/DVl
AUDIO
Use these analog audio inputs when connecting
devices to the TV's HDMI jacks. Unlike HDMI,
not carry audio information on the same cable.
analog audio from a personal computer, use
DVl AUDIO jacks instead.
DVI
DVl does
For
the PC=
7. PC=DVI
PC=DVI is a DVI-I input compatible with both DVI-A
(analog) and DVI-D (digital) inputs. Connect your personal
computer's HDMI, DVI, or VGA video output to this jack. An
adapter or converter cable may be required. Please see
Appendix B for signal compatibility. To hear audio from
the computer, connect analog audio cables from the computer to the PO=DVl AUDIO jacks.
1394
These jacks allow the TV to connect to external IEEE 1394
digital products by means of a single cable. See chapter
7, "Using IEEE 1394 Devices" for detailed information
regarding IEEE 1394 connections and recording.
10. MONITOR
OUT
Use these composite video and left/right audio jacks
to send analog video and audio signals to an external
recording device such as a VCR. The signals from these
jacks are from the program currently being viewed on the
TV screen. To make recordings from this output, the
TV must be in normal full=screen mode rather than in
mode.
=
From this output you can record audio and video
signals from ANT 1, ANT 2, iNPUT 1=3, and
IEEE 1394 devices.
•
Digital signals from ANT 1, ANT 2, and IEEE
1394 devices are converted to analog video and
audio signals.
Some signals cannot be recorded because of
copy-protection flags in the content.
11. AUDIO
These inputs are ._implay/-/D certified for proper interoperability with other products certified by Simplay TM.
19
OUT
LEFT/RIGHT
AUDIO
OUT LEFT/RIGHT
jacks send analog audio of
the program currently shown on the screen to an A/V surround sound receiver or stereo system. Digital audio from
digital channels, FireWire® (DTVLink/IEEE 1394) devices
and HDMI devices is converted to analog audio by the TV.
If using an analog A/V receiver or stereo system, this is
the only audio connection needed between it and the TV.
12. DiGiTAL AUDIO
OUT
This output sends Dolby Digital or PCM digital audio to your
digital A/V surround sound receiver. Analog audio from
analog channels and devices is converted by the TV to PCM
digital audio. If you have a digital A/V receiver, in most
cases this is the only audio connection needed between the
TV and your A/V receiver.
TV Connections
Before
You Begin
Choosing a Language for Menus ..........................
ClearThought®
Easy Connect Auto input Sensing
Digital Video and Home Recording
........................
Connection Types ...................................
...............
22
22
23
24
HDTV Cable Box or Satellite Receiver with Component Video ....
Standard Cable Box, Satellite Receiver, or Other Device with
S=Video ..........................................
25
Wall Outlet Cable (no cable box) ..........................
Antenna with a Single Lead ............................
Antennas with Separate UHF and VHF Leads ................
VCR to an Antenna or Wall Outlet Cable ...................
26
27
27
28
VCR to a Cable Box (Audio & Video) ......................
HDMI Device (Cable Box, Satellite Receiver, DVD Player, or
Other Device) .........................................
DVl Video Device (Cable Box, Satellite Receiver, DVD Player,
or Other Device) ....................................
DVD Player with Component Video .......................
A/V Receiver (Stereo System) ..........................
Older Cable Box ....................................
Camcorder ........................................
29
25
30
30
31
31
32
32
22
Chapter
2. TV Connections
Before You Begin
Choosing
a Language
3_
Press EXITto close the screen. If you connected
several devices at the same time, the screen for the
next connection will open.
for Menus
When you power on the TV for the first time, you can
select either English or Spanish for all menus. You can
later change the language through the Setup menu.
Figure 2. The Auto Input Sensing screen appears when a
device is first detected. Select a name for the connected
device in this screen.
Figure 1. The Welcome screen lets you change the menu
language when you first power on the TV.
ClearThought®
Sensing
Easy Connect
Auto
input
This TV's ClearThought® auto input sensing feature
allows it to detect most connections automatically. The
first time you connect each device you will be prompted
to identify it by selecting from a pre-set list of device
names. The table below defines how connections on
each TV jack are handled.
More
ANT
l/ANT
Auto
Input
Sensing
•
You can change the input name at a later time using
the Input Name menu.
•
If you disconnect a device and then later connect a
different device to the unused jack, open the Input
Name menu to update the device name.
•
Antenna inputs (ANT
never detected.
•
Be careful to choose different names for each input.
IEEE
INPUT 1, 2, 3 video jacks
About
l/ANT
2) and TV outputs are
1394 Connections
2
The screen in figure 3 appears when you make an IEEE
1394 connection,
......................................................................................................................................................................................................
MONITOR
OUT (all jaCKS)
iEEE 1394 Device with an Analog Connection.
IEEE 1394
*
If the device is powered off when connected, detection will occur when the device is next powered on.
Connect your devices to the TV.
The TV and the devices can be either on or off when
connecting. If the TV is powered off, the detection
process will occur the next time you turn on the TV.
When the Auto Input Sensing screen opens (figure
2), you can accept the default name or press A Y to
select from a list of device names (e.g., cable box,
DVD, Satellite, VCR).
Choose a name that will help you when selecting
inputs in the Input Selection menu.
Some IEEE 1394 devices have both digital and analog
outputs to the TV. If you have such a device, place a
check mark in the Analog Connection check box to:
•
Allow a cable box with both analog and digital outputs
to switch automatically between them.
•
Allow you to use a TV menu to select either the analog
or digital output from the device.
For instructions on switching between analog and digital
outputs, see chapter 7, "Using IEEE 1394 Devices."
Chapter
Before You Begin, continued
Name assigned
to the device
In the New 1394 Device screen, note the name
assigned to the device, as you will need to use the
same name in a later step. See figure 3.
4.
Complete setup for other devices through the Auto
Input Sensing screens.
5.
Display the Input Name menu. To do so, press MENU,
highlight the Input Name icon, and press ENTER.
6.
Highlight the analog input used for the analog connection to the IEEE 1394 device.
7.
Press A Y to scroll through the available names to
display the name you earlier noted for the IEEE 1394
device.
8.
Press EXIT.
Connect the device to the TV with an IEEE 1394 cable
and a supplemental
2.
analog connection.
at a Later Time (not
Disconnect the IEEE 1394 device from the TV.
2.
Reset all TV settings to their defaults using the TV
Reset service menu as follows:
a.
b.
c.
analog connection.
1.
Connection
1.
Figure 3. The ClearThought Auto Input Sensing screen for
IEEE 1394 devices includes a check box for an associated
to the
23
3.
To Add an Analog
recommended)
If your IEEE 1394 device has an analog connection
TV, follow the instructions below.
2. TV Connections
Press MENU
to display the Main menu.
Press 1 2 3 to open the Reset service menu.
Press ENTER.
3.
Reconnect the IEEE 1394 device to the TV.
4.
When the TV recognizes the device, place a check in
the Analog Connection check box.
5.
Press EXIT.
When the New 1394 Device screen appears, highlight
the Analog Connection check box and press ENTER
to
enter a check mark.
Note:
Digflal
it is important to check mark the box when
this screen appears upon first connecting the
device, as later changes can only be made after
returning all TV settings to their defaults.
Video and Home
Recording
The table below will help you decide which type of connection to use for digital video. Digital video comes to your
home in a compressed state, whether received on recorded media (e.g., disc) or broadcast over the air, over cable, or
via satellite. Some compressed digital video is available for recording as noted in the table.
HDMI or DVl
Compressed video is converted to
uncompressed form by an external device
such as a cable box, satellite receiver, or
DVD player before it is sent to the TV on an
HDMI or DVl cable.
You cannot record the resultant uncompressed
via HDMI or DVl.
video sent to the TV
IEEE 1394 (FireWire®} Connections
Your TV can receive and decode digital
channels, MPEG2 compressed digital audio,
and Dolby Digital audio.
You can record compressed digital video either
•
on compatible digital recorders as digital signals
•
as standard-definition
composite video from the MONITOR
OUT jack converted to analog signals
You may be unable to record some programming because of copy restric-
24
Chapter
2. 71/Connections
Connection Types
Video and Combined
These descriptions
Audio/Video
apply to TV video only and do not cover signals from personal computers.
Digital audio
and video
HDMI
Best
(carry highdefinition video
when available)
Good
Fair to Best
(depending on
source; carry
all qualities of
•
, ,
signals)
Note:
Carries uncompressed digital
video alone on a single one-wa_
DVl
Digital video
Component Video
Analog video
.___
S-V u_u
^ ....
._^^
,_._ uu v u_u
IEEE 1394
(FireWire®)
Digital audio
and video
,, ,
RF Coaxial vlueo
fig and
,
,
,
digital audio
and video
;
cable; requires separate audio
connections.
@@@
_
......
_
_
Carries analog high-definition
and standard-definition signals.
Y Pb Pr ROA-style connectors
are colored green, blue, and red.
_
_
t on s gna s Prov des better
"
quality video than composite or
RF coaxial video.
[_
video and audio as well as
device control signals on a
single two-way cable.
.......................................................................
i.............................................
i.........................
i....................................
_Jarr es aug o and v (::leo on a
.
_
_
_
single
CaDle,
Only some TV signals are high-definition signals. To view high-definition
programming from your cable or satellite provider, you must subscribe to
the provider's high-definition service. Some over-the-air broadcasts are in
high-definition and can be received with a high-quality antenna suited to
your location.
Audio=Only
Connections
There are two types of audio connections
Left/Right
i
Connections
used on this TV. Refer to the table below.
RCA-style connectors usually colored white for left and
red for right stereo audio. For monaural sound (all speakers playing the same sound), use only the white connector.
Analog
Stereo Audio
........
LJIglIal _ualo [L,oaxla U
_
_
RCA-style connector usually colored oiangel use to send
digital audio from the TV to your digital A/V receiver for
surround-sound effects. Usually the only audio connec-
i
Chapter
HDTV Cable Box or Satellite
Receiver with Component Video
25
trial antenna or cable service (not satellite) to ANT
l/MAIN
on the TV back panel. A coaxial splitter,
available at most electronics supply stores, may be
required to complete this installation.
If your cable box or satellite receiver has HDMI or DVI
outputs, use the connections for HDMI or DVI video
devices described later in this chapter.
Note:
Required: RCA component video cables, left/right
analog audio cables.
A coaxial splitter, available at most electronic supply
stores, may be required to complete this installation.
To receive the benefits of digital surround sound, connect the digital audio output from your cable box or
satellite receiver directly to your digital A/V receiver.
Standard Cable Box, Satellite
Receiver, or Other Device with
S=Video
Connect the cable from the outside cable or satellite service to CABLE iN or SATELLITE
iN on
the cable box or satellite receiver. See your device's
owner's guide for instructions and cable compatibility.
Required: S-Video cable and left/right analog stereo
audio cables.
SATELLITE iN
To
receiver
2. TV Connections
t.
1.
Connect the cable from the outside cable or satellite
service to CABLE iN or SATELLITE
IN on the
cable box or satellite receiver.
2.
Connect an S-Video cable from VIDEO OUT on the
cable box or satellite receiver back panel to INPUT
S=VIDEO on the TV back panel.
3.
Connect left (white) and right (red) audio cables from
AUDIO OUT on the cable box or satellite receiver to
INPUT/AUDIO
LEFT and AUDIO RIGHT on the
TV back panel.
Note:
Refer to the cable box or satellite receiver Owner's
Guide for cable or dish antenna connections to the
receiver.
!i¸
Figure 4. Connecting an external HDTV receiver with
component video connections
2.
Connect RCA-type cables from the Y Pb Pr outputs
on the HDTV cable box or satellite receiver to COM=
PONENT on the TV back panel, matching the
colored connections.
3.
Connect left (white) and right (red) audio cables from
the HDTV cable box or satellite receiver to COMPO=
NENT/AUDIO
LEFT and AUDIO RIGHT on the
TV back panel.
4.
Optional: To allow use of the Split Screen feature
with channels from ANT 1 and the cable box or
satellite receiver, connect the incoming terres-
Jill:
Figure 5. Connecting
I¸¸ i_i_ii!!iii!ii:!
¸¸I/:¸¸iiii_iiii!!iii
a device with S-Video
_!
ilili
26
Chapter
2. TV Connections
Wall Outlet Cable (no cable box)
(can be used with a CableCARD
and 65731)
TM,
models WD=57731
It is very important to connect the incoming cable for your
primary viewing source to ANT 1/MA|N,
especially for
CableCARD TM use.
1.
Connect the primary incoming coaxial lead cable to
ANT 1/MA|N
on the TV back panel.
2.
For an optional secondary antenna source, connect
an antenna (or cable) to ANT 2/AUX.
3.
If you have subscribed to a CableCARD TM service,
Insert the CableCARD into the CableCARD slot. The
top of the card must face in the direction indicated by
the CARD TOP arrow.
See chapter 1, "Television Overview," for additional
CableCARD information.
1. Primary Wall
Outlet Cable
To ANT I/MAIN
===
2.
Optional
Secondary
Antenna
or
Cable
3. CableCARD
l
i=
To ANT 2/AUX
ANT
2/AUX
ANT
CaI_AP,
TM
SLOT
TV back
Figure 6. Wall Outlet Cable
panel
detail
DTM_
...............
1/MAIN
_r
_¢_13
_
• C._RDTOPA
Chapter
Antenna with a Single Lead
A. For an antenna with fiat twin leads
A 300-ohm-to-75-ohm
transformer is required, This is not
included with the TV, but is available at most electronics
stores.
A1. For an antenna with flat twin leads, connect the 300ohm twin leads to the 300-ohm-to-75-ohm
transformer.
A2. Push the 75-ohm side of the transformer onto ANT
on the TV back panel.
B. For cable or antenna
with coaxial
1
2. TV Connections
Antennas with Separate
VHF Leads
27
UHF and
Required: UHF/VHF combiner
This is not included with the TV, but is available at most
electronics stores,
1,
Connect the UHF and VHF antenna leads to the UHF/
VHF combiner,
2,
Push the combiner onto ANT
1/MA|N
on the TV
back panel,
lead
Connect the coaxial lead directly to ANT
back panel,
1 on the TV
ANT
VHF
Antenna
(Channels
--
1/MAI[_
UHF Antenna
2-13)
(Channels
14-69)
Fiat Twin Lead_
External
Antenna
or Cable
[
3%°o%t°ornbiner
TV back panel
2,
To ANT 1/IVIAiN
i
Baek
Side
View
View
1.
Optional
300-Ohmto-75-Ohm
Matching
Transformer
Figure Z Connecting a Single Antenna
Figure 8. Connecting
separate UHF and VHF Antennas
i
28
Chapter
2. TV Connections
VCR to an Antenna or Wall Outlet
Cable
Required: Two-way RF splitter, 3 coaxial cables, right and
left analog audio cables, either S-video or video cable.
These are not included with the TV but are available at
most electronics stores.
1.
Connect the incoming cable or antenna to IN on the
RF splitter.
2.
Connect one coaxial cable from OUT on the RF splitter to ANTENNA
IN on the VCR back panel.
3.
Connect one coaxial cable from OUT on the RF splitter to ANT l/MAIN
on the TV back panel.
4.
To use the TV speakers with the VCR, connect left
(white) and right (red) audio cables from AUDIO
OUT on the VCR to INPUT/AUDIO
LEFT and
5.
Connect either an S-Video or composite video
cable from VIDEO OUT on the VCR back panel to
INPUT/VIDEO
or S=VlDEO on the TV back panel.
Connect only one type of video cable; S-Video is
recommended, if available.
Optional
To record high-definition digital channels converted
to analog standard-definition
video and analog stereo
audio, perform these two additional steps.
6.
Connect left (white) and right (red) audio cables
from AUDIO IN on the VCR to MONITOR
OUT
LEFT/RIGHT
on the TV back panel. If your VCR
is menu (non-stereo), connect only the white (left)
cable.
7.
Connect a composite video cable from VIDEO
IN on the VCR back panel to MONITOR
OUT/
VIDEO on the TV back panel.
AUDIO RIGHT on the TV back panel, If your VCR is
mono (non-stereo), connect only the white (left) cable,
VCR back panel
MONITOR
OUT
_.® 0to
Incoming
Cable
1.
RF Splitter
Figure 9. Connecting a VCR to an Antenna or Wall Outlet Cable
Chapter
1.
Connect the incoming cable to iN on the RF splitter.
2.
Connect one coaxial cable from OUT on the RF splitter to CABLE iN on the cable box.
3.
Connect one coaxial cable from OUT on the RF splitter to ANT l/MAIN
on the TV back panel.
Connect one coaxial cable from OUT on the cable
4.
box to ANTENNA
5.
Connect either an S-Video or composite video
cable from VIDEO OUT on the VCR back panel to
INPUT/VIDEO
or INPUT/S-VIDEO
on the TV
back panel. Connect only one type of video cable. SVideo is recommended, if available.
7.
Optional
8.
To allow recording from the TV to the VCR:
a.
Connect left (white) and right (red) audio cables
from AUDIO iN on the VCR back panel to
MONITOR
OUT/LEFT
and RIGHT on the TV
back panel.
b.
Connect a video cable from VIDEO iN on the
VCR back panel to MONITOR
OUT/VIDEO
on
the TV back panel.
iN on the VCR back panel.
Connect the cable box outputs to the TV as shown in
either figure 4 or figure 5, earlier in this chapter. This
connection allows the TV to receive the best available
signal directly from the cable box.
Figure 4: Component video output to the TV's
COMPONENT
Y Pb Pr jacks; analog stereo
audio to the associated AUDIO jacks.
Note:
Figure 5: S-Video output to the TV's
INPUT/S=VlDEO
jack; analog stereo audio to
the associated AUDIO jacks.
6.
When using this connection configuration with the
connections used in step 5, it is possible to view
live cable programs through the VCR Device. For
best picture quality always view live cable programs directly from the cable box device.
To use the TV speakers with the VCR, connect left
(white) and right (red) audio cables from AUDIO
7.
6.
of video cable.
m
Attach
only one type
7.
S-Video
Cable
Aodioo°dVidoo
5.
_===,,=,,=,,=,,=,,=Jfrom Cable Box
• to TV
Incoming
Cable
1.
RF Splitter
Figure 10. Connecting
3.
a VCR to a cable box
29
OUT on the VCR back panel to INPUT/AUDIO
LEFT and AUDIO RIGHT on the TV back panel.
If your VCR is mono (non-stereo), connect only the
white (left) cable.
VCR to a Cable Box (Audio & Video)
Required: Two-way RF splitter, 4 coaxial cables, right and
left audio cables, S-Video or composite video cable, plus
component or S-Video cables and audio cables required
to connect the TV to the cable box.
2. TV Connections
TV Back
Panel
30
Chapter
2. 71/Connections
HDMI Device (Cable Box, Satellite
Receiver, DVD Player, or Other Device)
Required: HDMI-to-HDMI
with the TV.
cable. This is not included
Connect an HDMI cable from the TV back panel to the
HDMI device output. HDMI devices provide video and
audio through this cable, so no other connection is
required. You can connect two HDMI devices to the TV
back panel through the HDMI connections.
DV! Video Device (Cable Box,
Satellite Receiver, DVD Player, or
Other Device)
Analog stereo audio cables and a DVI=to=HDMI cable or
DVl/HDMI adapter and HDMI cable are required. These
are not included with the TV. They may be available at
your local electronics retailer.
1.
Connect the DVI=to=HDMI cable (recommended) or
HDMI cable with DVl/HDMI adapter from the DVI
device's back panel to the TV back panel.
NOTE: If you are using a DVl/HDMI adapter, it is important to connect the adapter to the DVI device for
best performance.
2.
TV Back Panel
HDMI Device
NOTE: The HDMI connection
(HDCP).
Figure 11. Connecting an HDMI device.
Note:
Connect a set of audio cables from AUDIO OUT
on the DVI device back panel to the HDMI/DVl
AUDIO on the TV back panel. Connect the red
cable to the RIGHT jack and the white cable to the
LEFT jack.
supports copy protection
Some devices require connecting to an analog
input first, in order to view on-screen menus and
to select DVl as the ouput. Please review your
equipment instructions for DVl connectivity and
compatibility.
HDMI inputs are Simplay/-/z_ certified for proper
interoperability with other products certified by Simplay TM.
IMPORTANT
To connect a personal computer to the TV,
see chapter 6, "Using the TV with a Personal
Computer."
The NDIVll input processes signals as standard
motion video and is not designed to process
computer resolutions.
Figure 12. Connecting
a DVI device
Chapter
2. TV Connections
31
DVD Player with Component Video
A/V Receiver (Stereo System)
Component video cables and analog audio cables are
required. These are not included with the TV.
Most setups require either a digital audio cable or analog
stereo audio cables,
1.
Connect the component video cables from Y PB PR
VIDEO OUT on the back of the DVD player to the
COMPONENT
jacks on the TV back panel, matching the red, green, and blue colored connections.
2.
Connect left (white) and right (red) stereo audio
cables from AUDIO OUT on the back of the DVD
The TV makes all audio available in digital and analog
formats. Analog audio coming into the TV is available
in digital format on the DIGITAL AUDIO OUT jack.
Digital incoming audio is available in analog format on the
AUDIO OUT LEFT/RNGHTjacks.
Usually, only one of
the following connections is required:
player to COMPONENT/AUDIO
RIGHT on the TV back panel.
LEFT and
•
To connect an analog A/V receiver
Connect left (white) and right (red) audio cables from
AUDIO OUT/LEFT
and RIGHT on the TV back
panel to the TV AUDIO
iNPUT
on the A/V receiver.
To connect a digital A/V receiver with Dolby
Digital surround sound and PCM audio support
Connect one end of the digital audio cable to
DIGITAL AUDIO OUT on the back of the TV.
Connect the other end to the COAXIAL
DIGITAL
INPUT on the back of the A/V receiver.
AN
TV Back
Receiver
Panel
IN
Panel
i
DVD
Player
Back
Use if connecting
a
_,
Use if connecting an
Panel
Figure 13. Connecting a DVD player with component
video
I_
Figure 14. Connecting
receiver
audio from the TV to an A/V
Note:
[]
On rare occasions, an HDMI signal may be
copy-restricted and cannot be output from the TV
as a digital signal. To hear these copy-protected
signals through the A/V receiver, use connections
for analog A/V receivers.
Check the A/V receiver's Owner's Guide for
information concerning use of the digital input
and switching between digital sound and analog
stereo sound from the TV.
32
Chapter
2. TV Connections
Older Cable Box
Camcorder
Required: 3 coaxial cables, one two-way RF splitter.
These are not included with the TV.
Required: Analog stereo audio cables and either an SVideo or composite video cable.
When this setup is complete, you can use the TV remote
control, when programmed, to change channels on the
cable box.
NOTE: For IEEE 1394 camcorders, see also chapter 7,
"Using IEEE 1394 Devices."
Note:
This connection
is not recommended.
1.
Connect either an S-Video or composite video cable
from VIDEO OUT on the camcorder to iNPUT
3/VIDEO
or S=VIDEO on the TV. Connect only one
type of video cable; S-Video is recommended, if available.
2.
Connect left (white) and right (red) audio cables from
AUDIO OUT on the camcorder to iNPUT 3/
AUDIO L and AUDIO R on the TV.
The other
connections described in this chapter provide bet=
ter quality audio and video to the TV.
1.
Connect the incoming cable to iN on the RF splitter.
2.
Connect one coaxial cable from OUT on the RF split=
ter to ANT l/MAIN
on the TV back panel.
3.
Connect one coaxial cable from OUT on the RF split=
ter to IN on the standard cable box.
4.
Connect one coaxial cable from OUT on the cable
box to ANT 2/AUX
on the TV back panel.
S-Video
Cable
1.
omposite Video Cable
m
w
2.
Figure 15. Connecting
2
1.
an older cable box
Figure 16. Analog connections
for a camcorder
TV Operation
Remote Control
....................................
Choosing a Program Source ...........................
ChanneiView TM Channel Listings ........................
Status Display .....................................
TV Signals and Display Formats .........................
Split Screen .......................................
34
36
36
37
38
40
34
Chapter
3. TV Operation
Remote Control
12. FORMAT:
Changes the shape and size of the main TV
picture. When in Split Screen mode, changes the
size of the split images while maintaining their aspect
ratios.
Overview
Figure 1, next page
Slide Switch: Selects the A/V device to be controlled
by the remote control. Set the slide switch to TVfor
operation of the TV and IEEE 1394 devices. Control of
other device types requires programing (see chapter
3, "TV Operation").
2.
SLEEP:Sets the TV to turn off within 2 hours. See the
next page for instructions.
m
Digits/Letters:
Allow you to tune to a channel by
entering channel numbers; press ENTER
for faster
tuning. Use numbers and the CANCEL
key to enter digital
sub-channels. Also use for entering information into
menus.
To select letters when naming channels, repeatedly
press the associated number key. The following
special characters are available with the 1 and 0 keys:
13. INPUT:Displays the input Selection menu from which
you can select an input source to view, such as an
antenna input (ANT 1/2) or a connected device.
14. A Y 4 _ (Adjust Up/down/Left/Right):
menus and change settings.
Navigate
15. ENTER:Selects a channel number or menu item.
16. GUIDE:Displays or removes ChannelView
channel listing for ANT 1 and ANT 2.
TM
on-screen
17. INFO:Displays an on-screen summary of the current
device in use and any broadcast information available,
including current V-Chip information. See chapter 3,
"TV Operation," for details.
18. AUDIO:Selects individual audio settings for adjustment.
19. VIDEO:Selects individual video settings for adjustment.
20. MENU:Displays the main TV menu using the I/IBWPOilll
on-screen menu system. When a sub-menu is open,
backs up one level.
4m
=/CANCEL
(SUB-CHANNEL/CANCEL}:
When entering digital
channel numbers, adds a separator between main
and sub-channel numbers. Clears FAV and some
menu entries.
5.
POWER:
Turns TV power on and off.
6.
QV(QuickViewTM): Switches between the current
channel and the last channel viewed.
7.
MUTE:Turns TV sound off or on.
8.
SPLIT:Turns Split Screen mode on and off.
g.
VOLA/V
(Volume Up/Down):
Changes sound level.
10. CH/PAGE
A/V
(Channel or Page Up/Down):
Scans
up or down through memorized channels. Pages
up and down through screens when used with
ChannelView TM.
11 FAY(Favorites):
Scans through memorized lists of
favorite channels. See "Channel Menu" in chapter 4,
"TV Menu Settings," for more information.
21. EXIT:Closes all TV on-screen menus and displays and
returns to normal TV viewing.
22. F1-F4:When programmed, work like the A, B, C, D
buttons on some cable boxes and satellite receivers. Program the remote control for your equipment
and test the keys. See chapter 5, "Operating Other
Devices with the Remote Control."
24. (_ (PAUSE):
Freezes a broadcast TV picture when no
Split Screen image is displayed. When Split Screen is
displayed, freezes the sub-picture. See below for use
with recordable media.
Record/Playback
Keys
To enable the recording and playback functions, program
the remote for your VCR or DVD player/recorder and set
the slide switch to VOR
or DVD.See chapter 5 for instructions on programming the remote. If you have an IEEE
1394 device, see chapter 7 on IEEE 1394 devices.
23. (_
(RECORD):
Records with a VCR or DVD recorder.
24. (_ (PAUSE}:Pauses a VCR or DVD. See above for use
during TV viewing.
25. (_
(STOP):Stops play of a VCR or DVD.
26. (_
(REVERSE):
Rewinds a VCR. Reverse scans a DVD.
27. @
(PLAY):Plays a VCR or DVD.
28. _
(FAST
FORWARD}:
Fast forwards a VCR. Forward
scans a DVD.
Chapter
3. TV Operation
35
Remote Control, continued
®
Figure 2. The remote
batteries.
Sleep
control
requires
two AA alkaline
Timer
Setting the Sleep Timer
1. Press SLEEP
on the remote control.
2.
Press SLEEP
additional times to increase the time in 30minute increments up to the maximum of 120 minutes.
3.
Press EXITor wait five seconds without pressing any
buttons for the message to disappear.
4.
Press SLEEP
to view the time remaining before the sleep
timer turns off the TV.
Cancelling
the Sleep Timer
1.
Press SLEEP
to display the on-screen message.
2.
Press SLEEP
repeatedly until OFF is displayed.
Note:
After five seconds of inactivity, the message box
will disappear.
Care
For Best Results from the Remote
•
Control:
Use only alkaline batteries.
Be within 20 feet of the equipment.
=
Do not press two or more buttons at the same time
unless instructed to do so.
Do not allow unit to get wet or become heated.
Figure
Battery
1. Remote
Control
Avoid dropping on hard surfaces.
Overview
Do not use harsh chemicals to clean. Use only a soft,
lightly moistened cloth.
Installation
Do not mix old and new batteries.
Figure 2
1.
Remove the remote control's back cover by gently
pressing in the tab and lifting off the cover.
2.
Load the batteries, making sure the polarities (+) and
(-) are correct. For best results, insert the negative (-)
end first.
3.
Snap the cover back in place.
Do not heat, take apart, or throw batteries into fire.
Resetting
the Remote
Control
If the slide switch is set to TVand the TV does not respond
properly, do the following to reset the remote control.
1.
Press and hold POWER
for several seconds until the
2.
button blinks twice and goes off.
Release the POWER
button.
3.
Press keys 0 0 9 3 5 and the POWER
button will blink
twice when you finish entering the code.
36
Chapter
3. TV Operation
Choosing a Program Source
NOTE: If your only viewing sources are connected to the
ANT 1 and ANT 2 antenna jacks, you can switch
inputs without the Input Selection menu. Press
INPUT
to switch between ANT 1 and ANT 2. To
verify which is the current source while watching
TV, press INF0to see the on-screen status display.
ChanneIView
from Multiple
Menu
Sources:
The input
The Input Selection menu allows you to select an input to
watch on the TV. The current input appears as a goldcolored icon.
1.
Press INPUT
on the TV's remote control to display the
Input Selection menu (Figure 2).
2.
To select a different input, press A Y 4 _ on the TV's
remote control to move the highlight through icons in
the input section.
Press ENTER
to switch to the device and close the menu.
3.
More About the input Selection
•
Menu
To assign meaningful labels to the icons, such as
"VCR" or "DVD," see the "Input Name" section of
chapter 4, "TV Menu Settings."
Channel Listings
ChannelView provides listings, as sent by the broadcasters, for memorized channels on ANT 1 or ANT 2. Digital
channels are indicated with a "D" and analog channels
with an "A." Digital channels are shown with the major
channel and sub-channels (or bitstreams). Analog
channel information is displayed as sent.
Note:
Selecting
Selection
TM
If limited data is shown or no program data appears, it is because the broadcaster is not sending
the information. This is not a defect of your TV.
ChannelView
channels one by one.
Scan quickly through memodzed channels. ...............
View de{aiied infoima{ion foi
digital channels,
Press PAGE
A/V.
...............
Piess A or Y io highiighi
a channel and press I_.
To rearrange the icons, see the "Icon Order" section of
chapter 4, "TV Menu Settings."
To use with IEEE 1394 devices, see additional information in chapter 7, "Using IEEE 1394 Devices."
Figure 3. ChannelView screen, current programs. Use
to exchange displays for current and future programs.
Figure 2. Input Selection menu
Figure 4. ChannelView screen, future programs on the
selected channel (digital channels only)
Chapter
Status Display
The on-screen status display appears when you turn on
the TV, change inputs, change channels, or press the INF0
3. TV Operation
button on the remote control. The most common displays
are shown below. Seldom or never do all the status indicators appear at the same time.
Aoo,og.rogrom
1.
Source Antenna or Input
2.
Analog Channel being received (If an antenna
source)
Channel Name (if or named in the Channel menu)
Signal Type Being Received. Possible:
From ANT-l, ANT-2, or INPUT jacks: 480i
From COMPONENT
jacks: 480i, 480p, 720p,
1080i
Screen Format in use
Possible:
3.
4.
5.
6.
7.
8.
9.
Analog 480i/480p signals: Standard, Expand,
Zoom, Stretch, Stretch Plus, Narrow
720p/1080i signals: Standard, Wide Expand
Stereo and/or SAP being broadcast. In Split
Screen mode, the speaker icon is on the right to
indicate the sub-picture is the sound source.
V-Chip Ratings
Channel is in current FAV bank (FAV bank 2)
Day and Time
Digital
1.
2.
3.
4.
5.
6.
7.
3 XXXX
ANT-1 3
480i Standard -_
_ Stereo SAP
•TV-PG DLSV
'_
Copy Once
FAY2
-Monday 11:00 AM
- Sleep Timer: 30
@-- MUTE
10.
11.
12.
13.
Sleep Timer remaining time
Split Screen picture source and channel
Audio Mute on
Copy-Protection Status. Possible:
Copy Once
Copy Never
Program
Ant-1 42-1 XXXXXXX
- HD Standard
-_" English
TV-PG DLSV
Status of D-VHS VCR or IEEE 1394 device
Counter of D-VHS VCR
3.
Special message line (shows only when a special
message is needed; may be seen with analog
signals)
Copy-Protection Status. Possible:
Copy Once: Program can be recorded
Copy No More: Program can never be recorded;
program may be moveable.
Copy Never [Retention Period]: Program can never
be recorded; may display program retention period
XXXXXXXXXXXXXX
®
Copy Never: 3 Days
FAV2
"_)
Monday 11:00 AM
Sleep Timer: 30
DVCR
HD Standard
iEEE 1394 Device
1.
2.
4.
(l_'Ant=l
Digital Major and Sub-Channel Number
Digital Channel Name (only if broadcast)
Signal Type Being Received
Possible: SD 4:3, SD 16:9, HD
Screen Format in Use
Possible:
SD 4:3: Standard, Expand, Zoom, Stretch, Stretch
Plus, Narrow
SD 16:9 or HD: Standard, Wide Expand
Language(s) being broadcast
Program Name (if broadcast)
Copy-Protection Status. Possible:
Copy Once: Program can be recorded
Copy Never [Retention Period]: Program can never
be recorded; may display program retention period
Digital
37
(_
TV=PG DLSV
Copy No More
Play 01:20:15 -_
Monday 11:00 AM
Sleep Timer: 30
(,3,_
---_,2)
Special Message Line
38
Chapter
3. TV Operation
TV Signals and Display Formats
TV Display
This is a widescreen TV, also known as a 16:9 TV. This
shape reflects the new types of images available from
HDTV and many DVDs. There are still many older style
narrow-screen images (called 4:3 aspect ratio) you will
encounter. While there is no perfect solution for displaying a squarish, narrower image on a wide screen,
Mitsubishi offers several display formats from which you
can choose.
Standard:
This is the full-screen format. HDTV signals
use this format. This format is useful for displaying
Anamorphic DVDs that have 1.78:1 or 1.85:1 aspect
ratios. Anamorphic DVDs that have a 2.35:1 aspect ratio
are displayed with black bars at the top and bottom, but
show the entire image correctly. Narrow (4:3) images
are stretched evenly from side to side. Available for all
signals.
Press FORMAT
on the TV remote control to cycle through the
available display formats. The last-used format for each
device is used when you return to that device.
Expand: This enlarges the picture to fill the screen, cropping off some of the image at the top and bottom. This is
useful for reducing the letter box top and bottom bars of
non-anamorphic DVD images. Available for 480i, 480p,
and digital SD 4:3 signals only.
Note:
o
o
o
Only standard format is available for Split Screen.
PC formats vary depending on the PC signal.
For 1080p signals from an HDMI input, see "Computer Display Formats" in chapter 6, "Using the TV
with a Personal Computer."
DVD Definitions
Anamorphic (or Enhanced for WideScreen TV)
These DVDs are recorded in a special way to properly
show widescreen images on 16:9 TV sets using the
Standard format mode. This is the recommended viewing
choice.
Non=Anamorphic
(or 4:3, 1:33:1, Letter Box, or Full
Screen)
These DVDs are recorded for use with traditionally
shaped, squarish TVs. They may be full screen (4:3 or
1:33:1) which crops movies to fit the narrow TV, or letter
box, which adds black top and bottom bars.
This information may be listed on the DVD case. Some
DVDs support both types of recordings.
Signal Definitions
480i Signals: Traditional analog interlaced signals from
or through ANT=I and 2, INPUT 1-3, COMPONENT
1 and 2, HDMI 1 and 2.
480p Signals:
Progressive-scan
DVD signals
PONENT
inputs and HDMI
1 and 2.
on COM=
Format
Definitions
Zoom: This enlarges the picture, cropping off some of
the image at each side and top and bottom. This is usdul
for removing or reducing the black top and bottom bars
on anamorphic DVDs with a 2.35:1 aspect ratio. Available
for 480i, 480p, and SD 4:3 signals only.
Stretch: This format stretches a narrow (4:3) image
across the screen; there is less stretch in the center than
at the sides, however. This allows the entire narrow image
to be displayed across the screen with less distortion
than is seen in the Standard format. Available for 480i,
480p, and SD 4:3 signals only.
Stretch Plus: Similar to stretch mode, but to minimize
distortions on the side, the picture is expanded to crop off
portions of the top and bottom. Except when displaying
menus or Split Screen, press A V to adjust the position of
the picture vertically. Available for 480i, 480p, and SD 4:3
signals only.
Narrow: This format displays narrow (4:3) images in their
original shape, and adds stationary black side bars to fill
the screen. Available for 480i, 480p, and SD 4:3 signals
only.
Wide Expand: Enlarges the picture, cropping some of
the image on both sides. This Expand format is useful
to remove or reduce black side bars added to narrow
images that are converted to 16:9 signals for digital
broadcast. Available for 1080i, 720p, digital SD 16:9 and
digital HD signals.
720p and 1080i Signals: High-definition signals received
through COMPONENT
inputs and HDMI 1 and 2.
These signals are always 16:9 (widescreen).
SD 4:3: Standard-definition
narrow-screen
format
from digital channels and IEEE 1394 devices.
SD 16:9: Standard-definition
widescreen format
from digital channels and IEEE 1394 devices.
HD: High-definition
wide-screen
channels and IEEE-1394 devices.
16:9 (widescreen).
format signals
These signals
signals
signals
from digital
are always
Note:
All high-definition channels send widescreen (16:9)
signals, but not all programming sent on these
channels was created for this format. As a result,
the broadcaster must convert such programming
for broadcast, and may stretch the image or add
side bars to fill the widescreen area.
Chapter
TV Display
3. TV Operation
39
Formats
See descriptions
on the preceding page.
ORIGINAL SIGNAL
Anamorphic DVD
ORIGINAL
SIGNAL
Non-anamorphic
or SD 4:3
TV Display
TV Display
Standard
Standard
(not recommended,
distorted)
(recommended)
not available for
HD, SD 16:9 or
analog 720p, 1080i
Expand
(recommended
kJ
Expand© ©
for letterboxed)
(not recommended,
Zoom
_
(not recommended,
distorted)
HD, SD 16:9 or
analog
720p, for
1080i
not available
not available for
HD, SD 16:9 or
analog 720p, 1080i
distorted)
(recommended
Stitch
for anamorphic
for standard
not available for
HD, SD 16:9 or
analog 720p, 1080i
broadcast)
(not recommended,
Stretch Plus
HD, SD 16:9 or
analog
720p, for
1080i
not available
_O
(recommended
for standard
2.35:1)
notaaiaStretch
efo O
HD, SD 16:9 or
analog 720p, 1080i
(recommended
not available for
HD, SD 16:9 or
analog 720p, 1080i
distorted)
not available
Stretch Plus
for
HD, SD 16:9 or
analog 720p, 108gi
broadcast)
(not recommended,
distorted)
not available for
HD, SD 16:9 or
Narrow
Narrow
analog 720p, 1080i
(not recommended,
fl_
distorted)
m
.m.'6_
Standard
Original HD or SD
16:9, 720p or 108gi
aa
Wide Expand
(_(_
digital SD 16:9, HD,
analog
available 1080i
only or
for720p
(with side bars in broadcast)
(recommended
to remove side bars)
40
Chapter
3. TV Operation
Split Screen
Split Screen allows you to view pictures from two different
sources at the same time. Split Screen is available when
you have video sources connected to the TV in addition to
any connections to ANT 1 and ANT 2.
Operation
Turn Split Screen on or off
and sub-pictures.
Check which picture is the sound source.
cate the sound source,
Change the source of the sub-picture.
i
1.
Press l_ to make the sub-picture
2.
Press INPUT
and move the highlight to the icon for the input you wish
to view as the sub-picture (see figure 5).
Press ENTER
to make the change.
3.
the sound source.
Grayed-out input icons are unavailable as Split Screen sources or with
the current source.
Change channels (when the input source is
ANT 1 or ANT 2).
•
Change ihe size of ihe main and sub_pictures,
Repeaiediy press FORMAT
io cycie ihrough piciure siZes
ing page for sample displays.
...........
WlaKe me sub picture Till me screen.
"SPLIT" appears under the
Video icon to distinguish
this menu from the input
Selection menu.
With the main picture as the sound source, enter the channel
number and press ENTER.
See the ioiiow-
1.
Press _, to make the sub-picture the sound source.
.........
z. _'ress SPLIT
to close bplk bcreen mode.
Choice of Split Screen
sub=Picture Sources
iMPORTANT
}plit Screen is unavailable
i
if:
Your only inputs are ANT 1 and ANT 2.
Either picture source is a 1080p signal from
an HDMi jack.
Either picture source is from a personal
computer.
Figure 5. Change the source of the sub-picture
Split Screen Input Selection menu.
with the
Chapter 3.
Split Screen
TV Operation
41
Displays
Display choices. Press the FORMAT
key
repeatedly while in Split Screen mode to
view different displays.
TV inputs for Split
Screen
The available Split Screen picture sources are listed below.
Available
picture
as either main picture or sub=
Available
as main picture only
•
•
iii
Analog channels
Devices on VIDEO/S=VIDEO
Devices on COMPONENT
inputs
inputs
Digital channels received from CableCARD
TM
iNPUT
* Only when main picture and sub-picture
** Only when main picture and sub-picture
Combinations
combinations.
are from different INPUT jacks
are from different COMPONENT
jacks
of picture sources you can view with Split Screen. Check marks indicate available
or either Antenna input
TV Menu Settings
3D Graphical _
Menu System .....................
Main Menu ........................................
44
45
Setup Menu .......................................
input Name Menu ...................................
icon Order Menu ...................................
Channel Menu .....................................
46
48
48
49
Captions Menu .....................................
Parental Lock Menu .................................
51
53
Setting a Pass Code .................................
Lock TV by Time and Front-Panel
Lock ......................
Rating Menus .....................................
Bypassing the Ratings Lock and Lock by Time .................
53
53
53
55
V=Chip Signal information
TV Ratings .......................................
Movie Ratings .....................................
Audio/Video
Menu
Audio Settings
Video Settings
..................................
.....................................
.....................................
56
56
57
58
59
44
Chapter
4. TV Menu
3D Graphical
Settings
Menu System
3D Graphical ViSWPBiUP
on-screen
Your TV has Mitsubishi's exclusive
operating system, which provides on-screen
information for menu choices and changes using the TV's remote control.
® Menu Screens
The ViSWPBilII
®system includes the following special features:
A picture (icon) is highlighted on the menu
screen when selected with the directional
arrows A Y _ I_. You may then make
changes within the menu or access submenus, if available.
You can also open sub-menus from a
button. Sometimes when you select a
button, an automatic function begins.
_i_0_i
® Remote
Control
•
The currently selected icon or button is highlighted
with a yellow outline; the text color is yellow.
•
On-screen instructions, shown in the message line at
the bottom of the menu, provide feature selection and
adjustment information.
•
Some on-screen menu options must be set before
other options are available.
Buttons
The following buttons on the remote control help you navigate within the
_i8_P_I ® system:
[] MENU
Display or close the Main menu or move back
one menu screen at a time.
[]
Close all menus and return to TV viewing.
EXIT
[] 4 _
(Adjust Left/Right
_ I_ to select a menu item to change
Keys)
L_! A T
(Adjust Up/Down Keys)
•
to change the settings.
"
to scroll through pre=set text=box entries.
select a check box.
Chapter
4. TV Menu
Settings
45
Main Menu
Press MENU
on the remote control to open the Main menu,
figure 1. See below for an overview of the options available
through the Main menu.
Figure 1. Main menu.
Setup
Captions
.
•
•
•
.
•
.
Select English or Spanish for menus and
on-screen displays.
Memorize the available channels for the
antenna or cable service connected to the
ANT 1 and ANT 2 jacks.
Set the TV's internal clock either manually
or have the TV set the clock automatically.
Set the TV Timer to turn on the TV automatically at a designated time.
Set the energy mode for power consumption when the TV is powered off.
Turn off Demo Mode.
View the TV's software version.
.
Parental
•
•
Name
Assign useful names to TV inputs so that you
can easily find them in the Input Selection
menu.
Icon Order
Rearrange icons in the Input Selection menu to
put frequently used icons first.
Channel
•
.
•
Edit channels for the ANT 1 and ANT 2
inputs.
Manually add or delete channels from
memory, name analog channels, or add
your favorite channels to a FAV (Favorites)
list.
View signal strength of a currently tuned
digital channel.
Lock
Block or allow programming based on
rating signals sent by the broadcast station.
Lock the TV by time.
Lock the front-panel buttons.
Audio/Video
•
Input
Display closed captions (if sent by the
broadcaster).
Select settings for analog or digital captions.
_,
•
•
_,
Reset a selected device's A/V memory to
the original factory settings.
Customize individual audio and video settings.
Display a blue screen when viewing a
device with no video signal or a poor video
signal.
Enable/disable Film Mode.
Turn the TV speakers on or off.
46
Chapter
4. TV Menu
Settings
Setup Menu
channels from memory, naming channels, and saving
favorite channels in custom memory banks.
Note:
If using a CableCARD TM, the complete list of
available channels is provided through the
CableCARD and the ANT 1 option is grayed out.
Clock
(Setup
Menu)
Set the clock if you wish to use the TV's Timer function
or schedule delayed recordings. You can use either the
manual or auto method to set the clock.
Figure
2. Setup
Language
menu
(Setup
Menu)
Choose to display the on-screen menus in either English
or Spanish (EspaEol).
To listen to audio in other languages (when available), see
the "Audio Settings" section in this chapter and refer to
"SAP" (analog signal) or "Language" (digital signal).
Memorize
Channels
For ANT l/MAIN
(Setup
Menu)
and ANT 2/AUX
Setting
The memorization process performs two scans of all
possible channels on the selected ANT input. Analog
channels are scanned first, then the process is repeated
for digital channels. Channel memorization may take up
to 15 minutes to complete.
To start channel
1.
memorization
Highlight an input selection based on your connections:
Ant 1 Air,
Ant 2 Air
When connected
antenna
Figure 3. Clock submenu
to an indoor/outdoor
the Clock
Manually
Time
With the hour highlighted in yellow characters, press A Y
repeatedly to slowly increment the hour and associated
AM/PM indicator or press and hold to quickly increment
the hour. Press ENTER
to highlight the minutes in yellow.
Press A Y to set the minutes.
Date
With the month highlighted in yellow characters, press
A Y to select the correct month. Press ENTER
to highlight
the day. Press A V to select the correct day. Press ENTER
to highlight the year. Press ,& Y to select the current
year.
Time Zone
Ant 2 Cable
2.
cable box)
Press ENTER
to start automatic channel memorization.
To stop channel memorization
Press CANCEL.
before completion
Channels memorized before you pressed CANCEL
are
retained in memory. If you restart memorization, all previously memorized channels for the selected antenna input
are erased and the process starts over from the beginning.
After channel memorization, press OH/_/V to tune
to memorized channels. Select the Channel menu for
further channel editing, such as adding and deleting
Select your correct time zone. Press A or Y to select
the time zone for your area (Atlantic, Eastern, Central,
Mountain, Pacific, Alaska or Hawaii). Press _ to move
to the Daylight Savings option.
Daylight Savings
Press A or V to select either Applies or ignore, depending on whether or not daylight savings time is in effect.
This setting is used by ChannelView for channel listings
and does not cause the TV's clock to adjust to daylight
savings time; you must manually set the TV's clock
ahead or back each time the time change occurs.
Setting
the Clock Automatically
Select the Time Zone and the Daylight Savings (DST)
options for your state. Press A V to select Applies or
Ignore. You may then tune to a channel on ANT 1 or
Chapter
Setup Menu, continued
ANT 2 that uses Extended Data Service (XDS) time data,
typically a PBS channel. With Auto selected, the TV
automatically retrieves the correct time and date information from this channel.
Be aware that if a channel displays incorrect time information, it is because of information sent from the broadcaster and is not a defect of the TV.
Note:
You may find that some channels send the incorrect time and the TV clock is reset every time you
tune to those channels. To prevent unwanted
clock resets, first use the Auto method to set the
clock from a channel sending the correct time,
then change the method to Manual.
Timer (Setup
4. TV Menu
Settings
the hour. Press ENTER
to highlight the minutes.
to set the minutes.
47
Press A Y
Device
Press _, or Y to select the device to use when the Timer
turns on the TV. If the TV is already on at the selected
time, the Timer will switch the TV to this device.
Channel
When the selected device is an antenna, you can select a
channel for the TV to tune to when it comes on. Highlight
the Channel box and
•
press OH/_/",/or
channels.
A Y to choose from memorized
Enter a channel number from the remote control.
You can also enter sub-channel numbers for
digital channels.
Menu)
Energy
Mode (Setup
Menu)
The Energy Mode option lets you select the TV's level of
power consumption while the TV is turned off. Choose
either Low Power or Fast Power On. The Low Power
setting uses less energy, but TV power-on takes longer.
The default is Fast Power On. Keep this setting at Fast
Power On if you:
•
Need faster power on.
Wish to turn off the TV while recording to an IEEE
1394 device.
Wish to schedule future IEEE 1394 recordings for
a time when the TV will be off.
Figure 4. Timer submenu
The Timer feature allows you to set a day and time for the
TV to turn on automatically and the device and channel to
display when it switches on. If the TV is already on at the
requested time, the TV automatically tunes to the channel
you designated in the Timer menu.
When the Timer turns on the TV, the following message is
displayed: "Press a button for the TV to stay on." Press
any button on the remote control within five minutes if you
wish the TV to remain on.
Note:
The TV clock must be set before you can use the
Timer feature (see preceding page to set the clock).
•
Expect to use the TV Timer function to turn on the
TV at a preselected time.
Need the TV Clock to remain accurate for the TV
Timer and for scheduling recordings. With the
Low Power setting, you must reset the TV Clock if
the TV is left turned off for over 48 hours.
Wish to receive updates to the ChannelView
channel listings.
Note:
TM
CableCARD TM requires the Fast Power On setting.
If you insert a CableCARD TM, the TV will automatically override a Low Power setting and change to
the Fast Power On setting.
On/Off
Press A Y to enable or disable the Timer.
Demo Mode Off (Setup
Set Day
Some TVs are shipped from the factory with Demo Mode
active for use in retail stores. If Demo Mode is active,
highlight the Demo Mode Off button and press ENTER.
Select the day or days that the TV will turn on automatically. Press A or T to select Daily, Mon=Fri (Monday
through Friday), or individual days of the week.
Set Time
With the hour highlighted in yellow characters, press A V
repeatedly to slowly increment the hour and associated
AM/PM indicator or press and hold to quickly increment
Software
Version
(Setup
Menu)
Menu)
For servicing purposes it may be necessary to know the
software version in your TV. This information is displayed
at the right side of the Setup menu screen.
48
Chapter
4. TV Menu
Settings
input Name Menu
icon Order Menu
Use the Input Name menu to assign useful labels to the TV
inputs that appear in the Input Selection menu. Unused
inputs appear grayed out and unselectable.
The Icon Order menu allows you to rearrange the device
icons that appear in the Input Selection menu. Change
the sequence to put frequently used icons at the start of
the list.
Use the PC DVl option to specify the type of video signal
coming from your computer, either Analog or Digital. For
more about this option, see chapter 6, "Using the TV with
a Personal Computer."
I
Detected
Inputs that Can
Be Renamed
I
I
t
Type of Video Signal from
Personal Computer
an input
1.
If you are currently watching the input you wish to
rename, change to another input. To do so, press INPUT
to open the Input Selection menu, highlight a different
input, and press ENTER.
2.
With the Input Name menu displayed, press 4 I_ to
move the highlight to the box for the input you wish to
rename.
3.
Press A V to select from the following list.
Cable Box
Camcorder
DVD
DVD2
DVR (digital video recorder,
DVD)
Game
HD Disc
Satellite
VCR
recordable
Only one VCR label is available, so If you have a
second VCR connected, leave the name as the default
name.
tht
_mes
name1°r more
con ,!on,besure
for each input.
the icon order
1.
Press A V 4 I_ to highlight the icon to be moved and
then press ENTER.
2.
Press _. Y 4 1_ to drag the icon to the desired position. Press ENTER
to set the new position.
I
Figure 5. Input Name menu
To rename
To change
Figure 6. Icon Order menu
Chapter
Channel Menu
4. TV Menu
Settings
49
weaker channels or delete unwanted channels using this
option. For example, if you wish to see only digital channels listed, use this menu to delete analog channels from
memory.
Press CR/_/V
to review the channels in memory. Press
A 'V' to select Added or Deleted for the channel shown in
the Channel box.
Name
II
Settings
Number
for the Channel
Shown
IL
mory
Signal-Strength
indicator
(digital channels only}
(Channel
(Channel
Menu)
Select the channel number affected by this menu in any of
three ways:
•
Press _, Y to move through all channel numbers, one
at a time. If you also wish to tune to the channel,
highlight the channel number and press ENTER.
Press CB/x/V
to select from channels already in
memory. If you also wish to tune to the channel, highlight the channel number and press ENTER.
Enter the number directly and press ENTER.Note that
with this method, you must press ENTER
for the screen
to display settings for the selected channel.
Channel numbers can be one part, analog or digital (up to
the number 16383), or two part for digital channels. For
a two-part digital channel, press _
on the remote to
enter a separator after the first, second, or third number,
depending on the broadcaster's channel information.
For digital channels, when the broadcaster has sent a
virtual channel number, the virtual channel number is
shown in the text box and the original physical digital
channel is shown below on screen as a reference. One
original channel number can be associated with several
different virtual channels.
Memory
(Channel
2.
Press a number key repeatedly to cycle through the
characters associated with the key. You can also use
A V to change a highlighted character.
Press ENTER
to set the letter and move to the next letter
Press CANCEL
to move back one position.
Menu)
Select either 1 (ANT 1 MAIN) or 2 (ANT 2 AUX) as the
antenna source for the channels you wish to edit.
Channel
1.
position.
Figure 7. Channel menu
Antenna
Analog channels from ANT I and ANT 2 can be named
with up to four characters. The name you enter here will
appear on the TV screen as part of the on-screen status
display. Digital channels may already be named if the
broadcaster sends the information.
Menu)
After the available channels have been memorized with
Memorize Channels on the Setup menu, you can add
Signal
Strength
(Channel
Menu)
Displays the approximate signal strength of the currently
tuned digital channel. Use this indicator to help you
adjust the antenna direction for best signal reception.
The taller the bar, the stronger the signal. This indicator
applies only to digital channels.
To view the effects of antenna adjustments on digital
channels, tune to the digital channel you wish to measure
while remaining in this menu. To tune to a channel, either:
Highlight the channel box, press ON/%/V or A Y to
display the desired channel number, and press ENTER.
Enter the channel number on the remote control and
press ENTER.
50
Chapter
4. TV Menu
Settings
Channel Menu, continued
FAV {Channel
Menu)
The FAV feature allows you to put together lists of your
favorite channels available on the antenna inputs. You can
store channels in any of the nine different FAV memory
banks. You can also store the same channel in multiple
memory banks.
Once you have added a channel to FAV memory, FAY
and the memory bank number appear under the tuned
channel number on the TV screen. You can access the
FAV feature through the Channel menu or you can bypass
the menu and use only the remote control.
Adding FAV Channels
Menu
Removing
Using the
AVChannels
Using
the
Menu
1.
Select the channel using one of the methods described on the preceding
page.
2.
Highlight the desired bank (FAVl-FAV9).
3.
Press ENTER
to check mark the selected FAV memory bank.
4.
Repeat for additional channels or banks.
il
Wiih ihe channei
2.
Press ENTER
to remove the check mark.
seieciedl
high[ighi ihe box foi ihe FAV bank numbeil ..............
memory bank number appear under the channel number, the channel has
been successfully added.
Removing
FAV Channels
Viewing and Changing
FAV Banks
This procedure removes the channel only from the selected bank and leaves
the other banks unchanged.
1.
Press the FAYbutton and then the memory bank number.
2.
Press the FAYbutton repeatedly until you see the desired channel.
3.
While the channel number and FAY indicator (with correct bank number)
are still displayed on the screen, press CANCEL.For the channel to be
removed, you must press the CANCEL
button before the indicator disappears.
1.
Press the FAVbutton.
2.
To change memory banks, press a number button within one-half second
of pressing the FAYbutton.
3.
Press the FAYbutton repeatedly to cycle through the channels available in
that bank.
Chapter
4. TV Menu
Settings
51
Captions Menu
Digital
For analog channels, broadcasters can send either standard closed captions or text service. Standard closed
captions follow the dialogue of the characters on screen
and display in a small section of the screen. Text-service
closed captions often contain information such as
weather or news and cover a large portion of the screen.
The following display options are available for digital
sources:
For digital channels, broadcasters can send up to six different captioning selections or can send analog captions
that are the same as those sent by the analog station.
Each TV station may broadcast only one or two types of
captions or none at all. The TV cannot decode closed
captions received on component or HDMI inputs.
Captions
Captions 1-6:
Sent by broadcaster.
On if Mute: Closed captions are displayed when
audio is muted. When selected, press MUTE
on the TV
remote control to turn captioning on/off (Caption 1).
Off:
No closed captions.
Note: For digital programs, if the broadcaster is
sending only analog captions converted to digital
format, then the analog caption settings apply.
Appearance
The closed-captions provider selects the default options
when sending digital closed captions. Select Custom to
override defaults and customize the appearance of closed
captions. These settings do not apply to analog closed
captioning converted to digital.
Digital Settings
Figure
8. Captions
Analog
The Digital Settings menu allows you to customize the
appearance of the closed captions sent by the broadcaster. Digital settings do not apply to analog closed
captions converted to digital.
menu
To open the Digital Settings menu, select Custom for the
Appearance
option. Move the highlight to the Digital
Settings icon and press ENTER.
Captions
The TV can display one of the following captions for
analog sources:
•
CC1, 0C2,003,
signals
or 0C4:
standard closed-caption
o
Text1, Text2, Text3, or Text4: Text-service signals
o
On if mute: Closed captions appear when audio is
muted. When selected, press MUTE
on the TV remote
control to turn on/off the standard closed-caption
signal CCl.
•
Off:
No closed captions.
Figure 9. Closed Captions, Digital Settings sub-menu
Background
Font
To make the analog closed captions easier to read, you
can choose to display the background color as either
black or gray behind the text.
The available font options are as follows:
•
Default:
vider
1:
2:
3:
4:
5:
6:
Selected by the closed-captions
__ed
__ack
captioning
is
or gray box appears
Font
Font
Font
Font
Font
Font
_
signal is broadcast.
Font 7: Small capitals
pro-
Monospaced font with serifs
Proportionally spaced font with serifs
Monospaced font without serifs
Proportionally spaced without serifs
Casual font
Cursive font
52
Chapter
4. TV Menu
Settings
Captions Menu, continued
Opacity
(Font)
You can customize the visibility of your fonts using the following settings:
Size
•
Translucent:
Select the desired font size. Large is the recommended
font size.
Color
The available font colors are listed below. Text and background cannot be set to the same color.
White
Black
Magenta
Red
Yellow
Green
Cyan
Blue
•
Solid text blocks view of the TV program
Flashing:
Text flashes at intervals
Opacity
You can customize the background for digital captions
using the following settings:
Translucent:
background
Transparent:
the background color to make the digital
easier to read. The available background
below. Text and background cannot be
color.
White
Black
Yellow
Green
Magenta
Red
Cyan
Blue
Invisible text reveals the TV program
Opaque:
Background
Background
You can change
closed captions
colors are listed
set to the same
TV program is dimmed behind the text
Transparent:
behind.
Opaque:
•
TV program is dimmed behind the
No visible background
Solid background covers TV program
Flashing:
Background flashes at intervals
IMPORTANT
Mitsubishi recommends you use contrasting
colors for captions and background.
Black translucent
background
combined
with a white font makes an easy=to=read
combination.
The content
, broadcaster,
Use care when selecting custom colors. Your
choice may affect the readability of captions.
of captions is determined
by the
if your captions show strange
misspellings,
_
malfunction
or odd grammar,
of the TV.
it is
Chapter
Parental Lock Menu
Lock by Time (Parental
53
Lock
Lock Menu)
Lock by Time allows you to block all use of the TV during
specified hours. During the lock time, you must use your
pass code to view the TV. To lock the TV by time:
Ratings (U.S. Ratings/Other
Ratings)
V-Chip technology lets you restrict access to
programming based on program-rating signals sent
by the broadcaster. For U.S. ratings, you can also set
the time of day for these restrictions to be in effect.
1.
Press A Y to select On or Off for Lock by Time.
2.
Press _ to move to the Lock Time box.
Lock by Time
Lets you restrict TV use by time of day.
Front Panel Lock
=
Settings
Lock TV by Time and Front-Panel
The Parental Lock menu gives you control over three
different types of parental controls. You must use a
pass code to open this menu to enable/disable the lock
options. The three parental controls available are:
•
4. TV Menu
Lets you disable the controls on the front of the TV.
Use this option if there are small children near the TV
who may be tempted to press the buttons.
a.
With the hour number highlighted in yellow, press
A Y repeatedly to change the hour and associated AM/PM indicator. You can also just press
and hold to change the hour.
b.
Press ENTER
to move the highlight to the minutes.
c.
With the minutes number highlighted in yellow,
press A V repeatedly to change the minutes.
Just press and hold to move quickly through the
numbers.
d.
Press _ to move to the Unlock Time and set the
time as described above.
NOTE: To make Lock by Time active 24 hours a day, set
Lock and Unlock to the same time.
Front
Panel
Lock (Parental
Lock Menu)
Front Panel Lock lets you disable controls on the front
panel to prevent inadvertent changes to TV settings.
Select On to disable the buttons and select Off to restore
their operation.
I
II
I [
I
Figure 10. Parental Lock menu
To disable the front button lock without using the remote
control, press and hold the MENU
button on the front panel
for more than eight seconds. If the TV is on, a message
will display confirming release of the Front Panel Lock.
Setting
Rating
I
Access to
Ratings Menus
I
Lock TV by
Time
ITV Front Panel
Lock On/Off
a Pass Code
You are prompted to enter a pass code whenever you
select Parental Lock on the Main menu. To set a pass
code for the first time:
1.
Press MENU,
highlight Parental Lock, then press ENTER.
A screen prompting you for a pass code will display.
2.
Input a four-digit pass code using the number keys on
the remote control.
Press CANCEL
to delete a number and move
back one space.
Press MENU
or EXIT
to close the menu without
setting a pass code.
3.
Press ENTER
to set the pass code just input.
To reset the pass code, see the procedure in Appendix A.
Menus
The rating menus allow you to:
=
Turn rating restrictions on or off
Change the permitted rating level
Set the time of day to enforce rating restrictions
ratings only)
(U.S.
The TV comes from the factory with pre-set U.S. V-Chip
ratings and with the rating locks turned off. The pre-set
ratings are TV rating TV-PG and movie rating PG. If you
turn on V-Chip blocking, these presets allow only programs rated TV-PG/PG or lower until you change the
rating level.
After changing the channel or device, there may be a
delay of up to five seconds before the rating restrictions
take effect.
54
Chapter
4. TV Menu
Settings
Parental Lock Menu, continued
U.S. Ratings
8.
Menu
Use this menu to turn U.S. rating restrictions
to change the permitted rating levels.
on or off and
TV Content
Categories
9.
L
II
T
II
U.S. Restrictions On/Off
'
TV Rating and
Supplemental
Restrictions
I I
1
I
I
Restriction
Hours
Movie Rating
Figure 11. U.S. Ratings menu
Highlight the U.S. Ratings icon
on the Parental
Lock menu (figure 10) and press ENTER
to open the U.S.
Ratings menu (figure 11).
2.
Press A Y to select On or Off.
3.
If you selected On, press _ to move to the TV Rating
box.
4.
Press A V to select the TV rating level you want to
allow.
5.
Press _ to move to the TV content categories. This
section allows you to specify content blocking in addition to that blocked by the TV rating. See the section
on V-Chip ratings for an explanation of TV content
categories.
•
To set the time of day for these restrictions to be in
effect, press _- to move to the Start box. To make the
rating restrictions active twenty-four hours a day, set
Start and Stop to the same time. To set the time:
a.
With the hour number highlighted in yellow, press
J, V repeatedly to change the hour. You can also
just press and hold to change the hour.
b.
Press ENTER to move the highlight to the
minutes.
c.
With the minutes number highlighted in yellow,
press A Y repeatedly to change the minutes.
Just press and hold to move quickly through the
numbers.
d.
Repeat these steps for the Stop time.
Press MENU
to return to the Parental Lock menu or
press EXITto close all menus.
Other Ratings
Menu
This TV can recognize new rating systems that may come
into effect in the future. The Other Ratings menu allows
you to block digital programming based on such alternate
rating systems. The alternate rating systems will apply to
digital programming only.
Note:
The Other Ratings button remains inaccessible
until the TV receives signals for an alternate rating
system.
The first time you tune to a channel broadcasting an alternate rating system, the TV defaults to the most restrictive
setting. Use this menu to change the allowed rating if you
are unable to watch a program broadcast with an alternate
system.
Press A Y to move the highlight among the
categories.
Press ENTER
to add a check mark to each TV
content category you want to block.
6.
Press _ to move to the Programs Not Rated box.
Press ENTER
to add or remove a check mark to allow or
block programs that are not rated.
Note:
Use care when choosing to block unrated programming. News programs and emergency bulletins carry the "None" or "NR" (Not Rated) V-Chip
signal, and they are blocked with this option active.
Press _ to move to the Movie Rating box. Press A
Y to select the movie rating level you want to allow.
Detailed information on rating guidelines follows this
discussion of the Parental Lock menu.
Figure 12. The Other Ratings menu is available only if the
TV receives broadcast signals carrying an alternate rating
system.
Chapter
Parental Lock Menu, continued
1.
Highlight the button labelled Other Ratings on the
Parental Lock menu (figure 10) and press ENTER
to open
the Other Ratings menu (figure 12).
2.
Press A Y to select On or Off.
3.
If you selected On, press _- to move to the Rating
Group box.
Note that you can change settings only for the rating
system available on the currently tuned channel. In
the figure above, for example, the Canadian rating
system is in effect. To change settings at a later time
for the Canadian rating system, you must again tune
to a channel broadcasting the Canadian system.
4.
Press A V to select from the subgroups available for
the rating system--English
or French in this example.
5.
Press I_ to move to the Rating box.
6.
Press A Y to select the program rating level you want
to block.
7.
Press ENTER
to add a check mark to indicate blocking is
in effect for the rating. When a rating shows a check
mark, press ENTER
to remove the check mark and allow
programs with this rating.
8.
Repeat steps 3 through 7 for each additional
system you would like to set up.
9.
Press MENU
to return to the Parental Lock menu or
press EXITto close all menus.
Bypassing
Time
the Ratings
rating
Lock and Lock by
If you try to watch blocked programming, a notice appears
prompting you for a pass code. To use the TV:
=
Input your four-digit pass code and press ENTER.
=
Change to a channel airing an allowed program or
change to another device.
If you try to use the TV when it is locked by time, a similar
screen appears, prompting you for your pass code.
To reactivate the rating lock or TV Lock by Time after
using the pass code, power the TV off and then on.
4. TV Menu
Settings
55
56
Chapter
4. TV Menu
Settings
V=Chip Signal information
When provided by the broadcaster or program source,
V-Chip ratings let you control the types of programming
that can be viewed on the TV. When V-Chip ratings are
supplied, they are displayed when you change the channel
or press INF0on the remote control.
TV Ratings
TV ratings apply to TV programs and made-for-TV movies.
You can apply supplemental blocking to TV ratings based on
the TV content categories described below. TV ratings are:
TV-Y
TV=Y7
TV=G
TV=PG
Youth. For children under the age of 7.
Youth 7 and older.
General Audience. For the entire family to view.
Parental Guidance. Parental Guidance is
TV=14
recommended; may not be suitable for some
children.
Adolescent 14 and older. Not recommended for
TV=MA
children under the age of 14.
Mature Audience. For adults only.
TV Content
PG
Categories
FV Fantasy Violence.
Applies to TV-Y7 only.
D Sexual Dialog. Applies in different degrees to TV-PG
and TV-14.
L Adult Language. Applies in differing degrees to
TV-PG, TV-14, and TV-MA.
S Sexual Situations.
Applies in differing degrees to
TV-PG, TV-14, and TV-MA
V Violence (graphic or realistic). Applies in differing
degrees to TV-PG, TV-14, and TV-MA.
TV-Y7
X
X
X
X
X
X
TV content categories. Boxes marked with an "X" indicate
supplemental blocking you can apply to each rating level.
The TV rating you select is for the least-restrictive program
level allowed. For example, if you select TV-PG, programs rated TV-Y, TV-Y7, and TV-PG can be viewed, but
programs rated TV-14 and TV-MA are blocked.
When you select a TV content category to block, all TV
programs with the same content category listing are
blocked. For example, if you select to block V (Violence)
at the TV-14 level, any programs with the V category
listing rated TV-PG are also blocked.
Ratings
Movie ratings are the MPAA ratings used for theaterreleased and direct-to-video movies. Movie ratings are:
G
Used in association with the TV ratings above, TV content
categories allow you to apply supplemental blocking.
Apply supplemental blocking using the U.S. Ratings menu.
TV-MA
Movie
General Audience.
Designed for the entire family
to view.
Parental Guidance. Parental Guidance is
recommended,
children.
may not be suitable for some
PG-13 Parental Guidance, 13 and Older. Not
recommended for children under the age of 13.
R
Restricted.
Restricted in theaters to 17 years old
and older unless accompanied by an adult.
N0-17 No Children 17 or Under. Restricted in theaters
X
to 18 years old and older.
Adult. Designed for and restricted in theaters to
adult audiences only.
The movie rating you select is for the least-restrictive
program level that can be viewed. For example, if you
select the PG-13 rating, movies rated G, PG and PG-13
can be watched, but movies rated R, NC-17, and X are
blocked.
Programs Not Rated: This refers to programs that carry
no rating, such as news, sports, weather, emergency bulletins, or movies prior to or without MPAA ratings. This
does not include programs without V-Chip signals.
Chapter
Audio/Video Menu
4. TV Menu
Settings
57
When the original video was filmed on 30-frame-persecond cameras, the Auto setting automatically applies
video decoding, the same as used with the Off setting.
Film Mode is not effective for high-definition
signals.
TV Speakers
This selection turns the TV's internal speakers on or off.
Select Off when sending the sound through a separate
stereo system or surround sound A/V receiver.
Note:
Figure 13. Audio/Video
To prevent damage from a sudden increase in volume, turn the TV volume down low before changing this option to On.
Menu
Audio/Video
A/V Memory
Reset
A/V Memory Reset allows you to reset a specific input's
A/V settings to the original factory settings. Highlight the
box and press A. V to select the input name. Next press
ENTER.
The audio settings of Balance, Listen to, and Language
are general TV settings unaffected by A/V Memory Reset.
To reset all A/V settings at once, including the three
general settings, perform an A/V Reset by pressing the
front-panel buttons GUIDE
and FORMAT
simultaneously.
{Audio
and Video)
Each input or device has its own A!V memory. Press A
Y to select the input or device in the A/V Memory Reset
box, then select Audio or Video to adjust individual
settings. Press ENTER
to close the menu and display the
individual settings.
Use A V to cycle through the individual settings. Use
_ to change the setting values. Press EXITto return to
normal TV viewing. For descriptions of the individual A/V
settings, see the following pages.
Video
Mute
The default is On, which displays a blue background when
no signal is being received on the INPUT, COMPO=
NENT, or HDMI jacks.
Film Mode (480i signals
only)
Auto is the default setting. With Auto selected, the TV
automatically detects and applies film-decoding correction for images that originated on 24-frame-per-second
film cameras and were converted to 30-frame-per-second
video for broadcast (3:2 pulldown conversion). Try the
Off setting if the TV adds noticeable jagged edges to the
images.
Settings
and the Remote
Control
To adjust individual audio or video settings directly with
the remote control:
1.
Press AUDIO
or VIDEO
repeatedly to cycle through the
available settings.
2.
Press 4 _ to adjust the setting. The setting display
will disappear after five seconds of inactivity.
58
Chapter
Audio/Video
4. TV Menu
Settings
Stereo: Default setting. The TV plays stereo
broadcasts in stereo and mono broadcasts in
mono. The word Stereo is displayed when you
tune to a channel broadcasting in stereo.
Menu, continued
Audio Settings
Analog
and Digital
Audio
SAP (Second Audio Program): Additional monaural sound track that you cannot hear during
normal TV viewing. The SAP signal might be
related to the program you are watching, (such as
a sound track in a foreign language), or it might
be unrelated (such as a weather report). If an SAP
signal is broadcast, the letters SAP are displayed
when you tune to the channel.
Settings
Enter the audio adjustment mode using either the Audio/
Video menu or the AUDIO
key. Use _ _ to change settings.
The adjustable settings display a slider and corresponding
numeric value on screen. Values can be adjusted from 0
to 63, with 31 as the midpoint.
Note:
0
The effects of the audio settings of Bass, Treble,
Balance, and Surround affect only the sound
heard through the TV speakers.
Bass
Enhances or reduces low-pitched
0
Mono: Reduces background noise. Use when
receiving a weak stereo audio signal. All audio is
played mono with this setting.
sound.
Treble
Enhances or reduces high-pitched
sound.
Listen To is not available for 1394 devices or devices connected to the INPUT, COMPONENT
and HDMI jacks.
Digital=Only
Audio
Settings
0
Balance
Adjusts the level of sound between the left and right
TV speakers.
You can set digital-only audio settings while viewing either
analog or digital sources, but the settings affect only
broadcast digital content.
0
Surround
Creates simulated stereo and surround effects
0
through the TV speakers.
Your choices are:
•
Off:
=
Simulated Stereo: The TV creates a simulated
stereo effect when watching a non-stereo
program.
Surround Sound: The TV creates a simulated
=
No surround effects (default).
Language
Determines what possible language you can hear.
Your choices are:
English
Portuguese
French
German
Spanish
Other
Italian
surround effect when watching a stereo program.
0
Level Sound
When on, automatically equalizes the volume level
when there are significant sound-level differences
between program segments, such as between regular
programming and commercials.
•
To receive the best fidelity with music programs,
change this setting to Off.
•
When connecting to an A/V receiver, set Level
Sound to Off and turn off the TV speakers to
send full dynamics to the A/V receiver.
Analog-Only
Audio
Settings
IEEE ?394 Ampfifier
0
Balance
Adjusts the level of sound between the left and right
speakers. The slider range is 0-254, with 127 as the
midpoint.
0
Loudness
When on, makes the audio level more uniform.
0
Preset
Select the mode that matches the audio source.
Your choices are:
You can set analog-only audio settings while viewing
either analog or digital sources, but the settings affect
only broadcast analog content.
0
Listen To
Determines how your TV receives a broadcast audio
signal and plays the sound you hear.
Your choices are:
Settings
0
Off
Classical Music
Jazz
Movie
Rock
Speech
Equalizer
Equalizes the sound.
Chapter
Audio/Video
Video
0
Individual sliders for each color are displayed.
Highlighted text shows which slider you are adjusting.
Press CANCEL
while in the PerfectColor screen to reset
all colors to the default settings.
Settings
A slider displays on screen for some settings.
When the slider is displayed, it represents numeric
values, with 63 as the maximum, 31 as the midpoint, and 0 as the minimum.
Bright: Suited for most daytime viewing.
Natural: Suited for most nighttime viewing.
Brilliant:
The default setting. For use under
strong light.
Figure 14. Set PerfectColor
for each TV input.
0
Contrast (Bright/Natural/Brilliant):
Provides a slider
to adjust the white-to-black level. Low contrast
shows a variety of shades in darker images, while high
contrast shows darker images more uniformly black
and makes colors appear more vibrant. In most home
lighting situations, a medium contrast looks best.
High contrast is good for brightly lit environments.
Brightness (Bright/Natural/Brilliant):
Provides a slider
to adjust the overall brightness of the picture.
Tint: Provides a slider to adjust the red-to-green
Sharpness:
clarity.
Color Temperature (Bright/Natural/Brilliant):
you to adjust how white is displayed.
•
0
Allows
Low: White images have a warm cast. This
adjustment is an average and can vary due to
ambient room lighting, video scene brightness,
and the TV's age. Natural/Color Temp at the
low setting displays video at the 6500K industry
standard for NTSC pictures.
High: White images have a cool cast. This
setting may provide the most realistic picture
under bright lighting.
PerfectColorTM: Lets you adjust the intensity of
any or all of six colors (Magenta, Red, Yellow, Green,
Cyan and Blue) to create color balance for the current
image source. PerfectColor settings are memorized
independently
Computer
Video Settings
Video settings available for images from a personal computer are:
0
Contrast
Brightness
PerfectColor TM. The adjustment screen displays
without the vertical color bars when used for a com-
ratio.
Provides a slider to adjust the detail and
adjustments
Video Noise: Reduces minor noise (graininess) in
the picture. Use the Low setting with good-quality
signals. Use Medium or High with poor-quality
signals. Turn off to leave the picture unaltered.
Personal
Color: Provides a slider to adjust color intensity.
O
59
Picture Mode: Set the Picture Mode first before
adjusting other settings, as each Picture Mode stores
its own values for Contrast, Brightness, and Color
Temperature. Picture Modes allow you to optimize the
image for different lighting conditions. The Picture
Modes are:
•
•
•
0
Settings
for each TV input or device. Select the PerfectColor
option and press ENTER
to open the adjustment screen.
Menu, continued
Enter the video adjustment mode using either the Audio!
Video menu or the VIDEO
key. Press the VIDEO
key repeatedly
to cycle through the video options to the one you want to
change. Use 4 I1_to change settings.
Note:
4. TV Menu
puter image,
0
Auto Position: Press ENTER
to automatically
position of the PC video.
center the
0
HorizPosition
(Horizontal Position):
Manually
adjust the horizontal position of PC video. This selection overrides the Auto Position selection.
0
VertPosition
(Vertical Position):
Manually adjust the
vertical position of PC video. This selection overrides
the Auto Position selection.
0
Fine Detail: Manually adjust the picture quality of PC
video, analog signals only. This selection overrides
the Auto Position selection.
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
........ i_i__iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii__
¸;;i__i_i_i_i_i__iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
...............
Operating
Control
Other Devices with the Remote
Functions Available
for Other A/V Devices ..................
Programming
the Remote Control
.......................
Programming
Codes .................................
62
63
64
62
Chapter
5. Operating
Other
Devices
Functions Available for Other A/V
Devices
The TV's remote control can be programmed to operate
other types and brands of A/V products. To use the
remote when programmed, set the slide switch to the
position labelled for the product type. The functions performed in each switch position can vary depending on the
product. Not all functions work for all models. The most
common functions available are listed on this page.
with the Remote
+
ON/_./V
.
•
•
•
POWER
SLEEP
_ (FASTFORWARD)
•
_
(_
(PLAY)
(RECORD)
i"
_
(REVERSE)
•
_(PAUSE)
•
•
•
•
switch to the type of device you
wish to program for or control.
•
Mitsubishi VCRs are compatible
buttons.
•
•
Set the remote control's slide
Control
•
•
•
•
•
•
=
AUDIO
CANCEL
(on some
',
_ Number
(STOP) Buttons
0-9
with some additional
0=9Number Buttons (on
some models)
models)
•
FI=F4(A, B, C, D keys on
OH/_./V
some models)
ENTER
(on some
models)
The record/playback keys
(onsome models):
GUIDE
(on some models)
PG/x/V
•
(_ (FAST
FORWARD)
•
_ (PAUSE)
POWER
•
_ (PLAY}
AY _11I1, (on some
•
_(RECORD)
models)
•
_ (REVERSE)
VIDEO
•
_ (STOP)
MUTE
POWER
SLEEP
VOLUME
0-9 Number Buttons
Direct Input Selection
buttons: numbers,
FAV
and QV(on some
Mitsubishi models)
(not all functions for all models)
+
"
"
"
SLEEP
(_g_(FAST
FORWARD}
_ (PAUSE)
_ (PLAY)
(REVERSE)
(STOP)
0-9 Number Buttons
not all functions for all models)
•
•
•
•
"
•
models)
CNA/'-7(on
some
models)
ENTER
MENU
POWER
SLEEP
A Y 4 I_ (on some
models)
•
•
•
•
•
_ (PAUSE}
_ (PLAY)
_(RECORD)
_(REVERSE)
(_(STOP)
•
0-9Number Buttons (on
some models)
Chapter
Programming
Method
1.
1:
Code
5. Operating
the Remote Control
Other
6.
Devices
with the Remote
Control
63
Once you have found the correct code, write it in the
space below for future reference.
Entry
Move the slide switch at the top of the remote to the
position for the product you want to control. Refer to
the table below. Only one of each device type can be
controlled in each slide-switch position.
AUDIO
CABLE/SAT
VOR
Cable Box
DTV Receiver
Satellite Receiver
VCR
DVR
Laser Disc Player
DVD Player/Recorder
DVD
DVD Player/Recorder
DVR
Laser Disc Player
VCR
AUDIO
Press and hold POWER
on the remote control for several
3.
seconds until the button blinks twice and goes off.
Release the POWER
button.
4.
Enter the first five-digit code listed for your equipment.
The POWER
button blinks twice when you finish
entering a valid code.
Move the slide switch to another position if you
need to start over or wish to exit programming
mode.
5.
Point the remote control at the equipment and press
POWER.
If the product has no power on/off function,
press a different key, such as 1_ (PLAY),
(_ (STOP),
VOL/x or MUTE,
=
If the equipment responds, the remote control is
properly programmed to operate the equipment.
If the equipment does not respond, repeat steps
2-4 with the next five-digit code listed for your
equipment.
I:
__
_ging
Move the slide switch at the top of the remote control
to the correct position for the product. See the table
under "Method 1."
2.
Press and hold POWER
on the remote control for several
seconds until the button blinks twice and goes off.
3.
Press keys 9 9 1
4.
Press the number 1, 2, or 3 depending on the slideswitch position and the table below.
5.
Press OH/% and POWER
repeatedly until the product
responds by powering on or off. You can press CHV
to move backward through the code library if needed.
NOTE: If the product has no power on/off function, check
for a response using a different function. Press
1_ (PLAY),
(_ (STOP),
VOL/x, or MUTE
and then repeatedly press OHix/V
to check for a response.
6.
When the product responds, press ENTER
to set the
code.
Code
Verification
To determine the code programmed
the slide switch:
1.
2.
for any position of
Move the slide switch to the position you wish to
verify.
Press and hold POWER
on the remote control for several
seconds until the button blinks twice and goes off.
3.
Press keys 9 9 0
4.
Press 1 and count the blinks of the power button.
Write down the number of blinks as the first digit of
the code.
5.
Repeat step 4 for the second, third, fourth, and fifth
digits of the code.
iMPORTANT
to reprogra m the remote
the batteries.
Search
1.
The POWER
button blinks twice when you start to
enter the code and then once for each additional
keypress.
2: Code
In this method of programming, you step through the
remote control's internal code library to find the correct
code for your A/V product.
A/V Receiver
Audio Amplifier
CD Player*
2.
•
Method
64
Chapter
Audio Lock:
5. Operating
Universal
Other
A/V Receiver
Devices
Control
with the Remote
Control
Programming Codes
With Audio Lock active, the remote control operates
the volume and mute functions of the A!V receiver in all
positions of the slide switch. Activate Audio Lock if you
normally use an A/V receiver with your TV and other A/V
equipment.
1.
Program the AUDIO
position for your A/V receiver as
described earlier in this section.
2.
3.
Move the slide switch to the TVposition.
Press and hold POWER
on the remote control for several
Acurus
Adcom
AItec Lansinc
Bose
30674
......
Carver .........................................................................................................
30892
.....
_iasse...............................................................................
_
.......................................
seconds until the button blinks twice and goes off.
4.
Press keys0 9 3
The POWER
button will blink twice to indicate Audio Lock
is active.
To Reset the Remote Control to Operate
Volume and Mute for the TV Speakers
1.
Press and hold POWER
for several seconds until the
button blinks twice and goes off.
2.
Press keys9 9 3 V0L/X.
The POWER
button will blink four times to indicate Audio
Lock has cleared.
Durabrand
31561
....
E!an..............................................................................................................
3%47 ..............................................................
GE
Harman/Kardon
30892
JVC
30331
.......
Lenoxx
.................................................................................
30898....................................................
31561
......
Lex!con..........................................................................
Marantz
30892
......................................................................................................................
Mark Levinson
31483
.......
Mondia! .......................................................................................................
307_95...............................................................
30823 30395 30300
......
.......................................................................................................
3082330300
30257 30013
Polk Audio
30892
......
R#A .............................................................................................................
..................................................
Realistic
30395
Chapter
Programming
5. Operating
Other
Devices
with the Remote
Control
65
Codes, continued
RCA
31609, 31511, 31390, 31254,
31869
Audiotronic
....
Audiovox...........................
B&K
BK
.........................................................................................................
3!!89
...................................................
....................................................................................................................................
30840 30820 30701
..............................................
Sharper Image
....
3!80! ................................................................
31366 31361 ...................................................
31416, 31411,31410, 31409,
31622, 31558, 31529, 31503,
31458, 31441, 31406, 31382,
66
Chapter
Programming
Kenwood
5. Operating
Other
Devices
with the Remote
Control
Codes, continued
30826,
30072
30681, 30626, 30190,
KLH .......................................
3!7! 1 3!3-/3_ 3!3-72 313! _ ...........
30303
Technics
30029
ii130038 30029
....
Mc!ntosh .........................................................................................................
i306603029030256
................................................................................................
MCS
ii!30029
..................................................................................................................................................................
MGA
.............................................................................................................................................................................
.......................................................................................................................................................................
Miro
i36666 ....................................................................................................................................................................
....
Missio n .......................................................................................................
..............................................................................................................................................................................
ABC
10017,10014,10013,10011,
NAD
30299 30019
Optimus
31075, 31063, 30468, 30437,
30420,
30305,
30179,
30145,
30087, 30037 30032 30000
.................................................................................
....
_anasonic
..................................................................................................
6_ _6_ .......................................
_a_asoun_
_6
Cable Star
10056
Proton
Coolmax
10883
Director
10476
Eastern
10002
30305 30179 30053 30032
....................................................................................................................
...................................................................................................................................
......
_m_rson...................................................................................
....................................................
_rwoo8 ...................................................................................................
.........................................................................................................................
...............................................................................
......................................
............................................................................................................................................
....................................
10003
30490 30185 30100 30000
[
................................................................................................
..................................................
_6.............................
_
_6
_
]_
......
Chapter
Programming
5. Operating
Other
Devices
Hitachi
Micro
Jasco
Jerrold
Control
67
Codes, continued
'lvania
Hamlin
with the Remote
i10273,10259,10034,10020,
0009
10011
0007
!11602
i10315
10015
iiii10810,10476,10276,10024,
i10015,10014,10012,10011,
TeleCa
_Teleview
Texscan
TFC
Thomson
10001
'10258
10221
10040
i10001
10310
11256
.......
_3,_00!_
10003
..................................................
1020_ 10191,10153,10056,
_20872
68
Chapter
Programming
5. Operating
Other
Devices
with the Remote
Control
Codes, continued
Mclntosh
......
Memorex ....................................................................................................
_!2@ 2083! 20695 .....................................
Mathes
Gradiente
21087
Momitsu
21082
Pioneer
21571, 20632, 20631, 20571,
20490
20672
HarmaniKardon
Hitach! .......................................................................................................................
20664 20573
20522
Landel
Lecson
Lenoxx
LG
21533
21127
20869 20801 20741 20591
sonic B!ue
2!099 %%9
Sony
21533, 21431, 21033, 20864,
......................................................................................................................
20533
.....
_u_g_!_
Nagnavox...................................................................................................
Maata
21159
20782
::::
Chapter
Programming
5. Operating
Other
Devices
with the Remote
Control
69
Codes, continued
DirecTV
11856, 11749, 11640, 11639,
11609, 11444, 11443, 11442,
11414, 11392, 11377, 11142,
11109, 11108, 11076, 10819,
10749, 10724, 10639, 10566,
11535
....................................................................................
Jerrold
10869
10819,10749,10724,10722,
Polk Audio
20059 20023
20194
11749, 11285, 10819, 10790,
20451, 20217
U!tima teTv ..............................................................................
!!64
!!392 ...................................................
........................................................................................................
10724, 10722
......
11535....................................................
USDTV
11535
.....
%om........................................................................................
...................................................................................................................................................................................................................................................................
!
Zenith
11856
70
Chapter
Programming
5. Operating
Other
Devices
with the Remote
Control
Codes, continued
Harman/Kardon
Harwood
ABS
21972
20479 20209 20048
Hewlett Packard
21972
_i_acfii
.........................................................................
................
_iwa...............................................................................................
..............................
Alienware
Asha
HP
20041
21972
Humax
20000
21972
20739
_usB
........ ................................................
KEC
iiii20278 20037
20240
.... @@k .......................................................................................
.........................................
Carver
Cit!zen
Colt
Craig
9ydls ..............................................
.................................................
iii
20081
20278,20072 ...........................................................................................................................
LXI
i20037
20072
Daewoo
20020
21972
DirecTV
Durabrand
E!ectr0phonic
Emerex
20039
20038
MGA
ii 20307, 20240, 20209, 20162,
ii20104,20048,20047,20046,
i!!20039 20037 20035 20000 ....... i!
120240 20061 20043
_i21972
Mind
20037
.............................................................................................................................................................................
.................................................................................
....................
ii
.........
Emerson
................................................................................................................
....................................
20479, 20295, 20278, 20212,
20209, 20208, 20184, 20121,
20068, 20061, 20043, 20037,
ili¸F̧unai
....................................................................
20Q75 200672006!
....
Nikko
20037
20043
.....
i
Chapter
Programming
5. Operating
Other
Devices
with the Remote
Control
71
Codes, continued
Sine
20072
Sony
Optimus
21262, 21162, 21062, 21048,
Ph co
Philips
20035
;i21181,21081,20739,20618,
20110 20081 20062,20035
P!lot ...............................................................................................................................................
20037
Pioneer
....
............................................................................................................................................................................
....
20q6!..........................................................................................................................................
Portland
20020
.....................................................................................................
20240..............................................................................................
Unitech
Radix
Randex
Realistic
20037
20037
20202,20149,20106,20105,
20077 20060 20042
20104,20066,20062,20048,
20047,20046,20037,20035,
ii20479,20271,20209,20067,
Sanyo
:i20240,20159,20104,20047,
V[ew_!c ...............................................................................
' 21972..................................................
,
Voodoo .....................................................................................................
21972
Wards
.....
20081,20072,20062,20060,
20048,20047,20042,
20035,
Usin-i the TV with a Personal Computer
Setup ......................................
Video Adjustments
...........
Connecting a Computer to the TV
Adjusting image Resolution .....
Computer Display Formats .....
7,$
7,$
75
77
78
74
Chapter
6. Using the TV with a Personal
Setup
See the TV specifications in Appendix B to confirm
that your computer video signal is compatible with the
TV.
Note whether the computer supplies a digital or
analog video signal. You will need this information
during the setup procedure.
•
3.
Digital video signal: Comes from the computer's
DVl or HDMI output.
Analog video signal: Comes from the computer's
VGA 15-pin output and requires a VGA-to-DVl
cable or a VGA cable and VGA/DVl adapter.
Computer
Video Adjustments
1.
2.
Power on the computer if it is not already on.
3.
Change the resolution of the computer image. The
goal is to maximize the computer resolution while
maintaining a suitable aspect ratio for the image. See
the explanation later in this chapter.
4.
Perform TV video adjustments.
Press VIDEO
repeatedly to cycle through the video-adjustment options.
The following additional adjustments are available for
computer video:
Power on theTV.
Select PC from the Input Selection menu. To do this,
press INPUT
to open the Input Selection menu, move the
highlight to the PC icon, and press ENTER.
Auto Position. Press ENTER
to automatically
the position of the PC video.
center
HorizPosition (Horizontal Position). Manually
adjust the horizontal position of the PC. This
selection overrides the Auto Position selection.
VertPosition
(Vertical Position). Manually adjust
the vertical position of the PC. This selection
overrides the Auto Position selection.
4.
Press MENU
to open the Main menu, highlight the Input
Name icon and press ENTER.
5.
Highlight the PC=DVl text box and press Y to change
the setting to match your computer's video signal
type, either Digital or Analog.
Figure 1. Specify your computer's video signal type
(analog or digital) in the Input Name menu.
6. Press EXiTto close all menus.
7.
Connect the computer's video output to the TV's
PC-DVl jack. See the connection diagrams in this
chapter to find the method best suited to your equipment.
8.
Connect the computer's audio output using one of
these options:
Connect analog left/right audio to the TV's
PC =DVl AUDIO jack.
If your computer offers digital audio output,
connect it to a digital A/V receiver instead.
Fine Detail (analog DVI-A signals only). Manually
adjust the picture quality of the PC. This selection
overrides the Auto Position selection.
5_
Change the TV picture format to suit the image.
Press FORMAT
to cycle through the available picture
formats. See the chart later in this chapter showing
how various computer resolutions are displayed on
the TV.
Chapter
6. Using the TV with a Personal
Computer
75
Connecting a Computer to the TV
Computer
Computer
Required: HDMI-to-DVI cable or an HDMI cable with an
HDMI/DVl adapter, stereo audio cables
Required:
with DVl Monitor
Output
DVl-to-DVl cable, stereo audio cables
If the computer's audio output is a single mini jack, a mini
audio-to-RCA-male
"Y" adapter cable is also required.
1.
Connect the DVl-to-DVl cable from the computer DVi
output to the PC=DVI jack on the TV back panel.
2.
Connect the left (white) and right (red) audio cables
from AUDIO OUT on the PC back panel to PC=
DVi AUDIO on the TV back panel.
with HDMI Monitor Output
If the computer's audio output is a single mini jack, a mini
audio-to-RCA-male
"Y" adapter cable is also required.
1.
Connect the computer's HDIVI! output to the TV's
PC-DVl jack. Use either an HDMI-to-DVl cable or an
HDMI cable with an HDMI/DVl adapter.
2.
Connect the left (white) and right (red) audio cables
from the computer's AUDIO OUT to PC-DVI
AUDIO on the TV back panel.
t
iili
AUDIO OUT
iili
iiii!i
Figure 2. Connecting a personal computer with DVI Monitor
Output
Personal Computer
with HDMI Output
OUTPUT
Figure 3. Connecting
monitor output
a personal computer with an HDMI
76
Chapter
6. Using the TV with a Personal
Connecting a Computer to the TV,
continued
Computer
with VGA 15=Pin Monitor
(Analog Video)
Output
Required: 15-pin computer VGA-to-DVI cable or a VGA
computer cable and a DVl/VGA adapter, stereo audio
cable.
If the computer's audio output is a single mini jack, a mini
audio-to-RCA-male
"Y" adapter cable is also required.
__rst
__
_tion_
;;Name menu.
select the
PC DVl box of the input
See the "Setup" section forformore.more.
Connect the computer's PC MONITOR
OUT to
PC=DV| on the TV back panel. Use either a VGA-toDVl monitor cable or a VGA computer cable with a
VGA/DVl adapter.
Connect the left (white) and right (red) audio cables
from the computer's analog audio ouput to PC=DV|
AUDIO on the TV back panel.
Computer
with
VGA
Monitor
Output
Figure 4. Connecting a computer with a VGA 15-pin monitor
output.
Computer
Chapter 6.
Adjusting
image Resolution
Your Mitsubishi TV can display resolutions from standard
VGA (640 x 480) through 1920 x 1080 signals at a refresh
rate of 60 Hz. Note that 1280 x 1024 and 1920 x 1080
signals are supported only for digital computer signals,
and 1920 x 1080 at 24, 30, and 60 Hz. See Appendix B in
this book for more on compatible screen resolutions.
In most cases, the computer
match to display on the TV.
if you wish. The instructions
resolution on most personal
will select the best resolution
You can override this setting
below are for setting the
computers.
1.
2.
In the PC's Start menu, select Settings.
Select Control Panel.
3.
Select Display.
4.
Choose the Settings
5.
Change the resolution to the highest resolution with
the aspect ratio best suited for the image. See the
table on the next page showing possible PC formats.
Depending on your computer's operating system,
adjust the resolution with either:
= the Screen area slider.
•
the Screen Resolution slider
1.
tab.
2.
Figure 5. Computer resolution, XGA selection
3.
Using the TV with a Personal
Computer
77
6.
To change the refresh rate, click on the Advanced
button.
7.
On the Monitor tab, select a setting from the Screen
refresh rate drop-down list. The resolution of 1920 x
1080 is supported at 24, 30, and 60 Hz; other resolutions are supported at 60 Hz.
You may need to restart the computer for this change to
take effect.
NOTE: Whenever the TV is powered on, the lamp is in
use, even if the TV screen appears dark. As a
reminder that the TV is powered on and that time
is being added to the lamp's elapsed hours, set
the computer's screen saver to a pattern that will
display after several minutes of inactivity.
78
Chapter
6. Using the TV with a Personal
Computer Display
Formats
VGA
640 X 480
WVGA
848 X 480
WSVGA
1064 X 600
XGA
1024 X 768
1280 X 720
WXGA
1365 X 768
SXGA
1280 X 1024
Computer
Repeatedly press the FORMAT
key to cycle through the TV displays
available for your computer's video signal.
Ising IEEE 1394 Devices
Overview
.....................................
Recording to IEEE 1394 Recordable
Devices ............
The TV Remote Control and IEEE 1394 Devices ..........
A/V Discs .....................................
Switching
Between
Analog
and Digital IEEE 1394 Outputs
. .
8O
82
84
85
86
80
Chapter
7. Using IEEE 1394 Devices
Overview
Compatible
,: iiiii
liiiiiii, iiii i
IEEE 1394 Devices
Compatible A/V devices include some, but not all, cable
boxes, D-VHS VCRs, A/V discs, and future products.
Some devices may have IEEE 1394 connectors but are not
compatible with the TV. Areas of compatibility to consider
are:
4-pin connector
6-pin connector
6-pin-to-4-pin adapter
1. Digital Video Signals
The TV can decode MPEG2 video as provided by cable
boxes and some camcorders. Many camcorders provide
DV video, which the TV cannot decode. Connect a DV
camcorder to the TV using analog audio plus composite
video, S-video, or component video, or use HDMI audio/
video. Other types of digital video, such as PC video
provided by some computers, must be decoded by the
source device and sent to the TV as analog video, S-video,
or DVI/HDMI video.
If you wish to connect a 6-pin device to the TV (such as a
camcorder), and the device is designed to receive electrical power from another 6-pin device, there are several
ways to provide electrical power to the device:
2. Digital Audio Signals
When received with video signals, the TV can decode
Dolby Digital signals and MPEG audio signals. Other
types of digital audio as provided by some digital recording devices, such as MP3 audio and DTS audio, cannot be
decoded by the TV when received over IEEE 1394 connections.
There are two connection methods for IEEE1394 devices. Use
the method that fits your network of audio/video products.
The TV may not be able to pass incompatible digital audio
signals on the coaxial digital audio output. These signals
may pass to other devices, however, on the IEEE 1394 cable.
3. Digital Control Signal
The TV can serve as the control center for IEEE 1394
audio/video devices, such as VCRs, A/V Discs, tuners,
cable boxes, and amplifiers that are compatible with the
following IEEE 1394 control standards.
•
EIA-775. Designed for tuning devices such as cable
boxes, allowing the device to send simple graphics. This standard does not, however, allow the TV to
control the cable box by IEEE 1394.
AV/C (Audio Video Control). Designed to provide
basic controls such as play, stop, channel selection,
and volume, as appropriate for the device.
Four=Pin and 6=Pin Connections
There are two different types of connectors used for IEEE
1394 terminals and cables: a 4-pin and a 6-pin type.
Both types send the same digital audio, video, and control
signals, but the 6-pin connectors can also supply lowvoltage electrical power to connected devices. This TV
uses only 4-pin type connectors.
A 6-pin connector cannot be connected directly
jack, and vice versa. To connect a 6-pin device
device, use a 6-pin-to-4-pin adapter or adapter
These cables are available from electronics and
stores.
to a 4-pin
to a 4-pin
cable.
computer
Connect the camcorder directly to the household AC.
Use the camcorder's battery for power.
Connect the camcorder directly to another 6-pin
device in the network that can provide power.
Connection
Methods
Direct Device-To-Device
Method
The IEEE 1394 interface allows you to chain devices,
unlike audio and video connections that require you to
connect each individual device directly to the TV. For
example, you can connect your D-VHS to your 1394 A/V
disc and then connect the 1394 A/V disc to the TV. The
resulting IEEE 1394 chain allows you to add more devices
to the chain. You will see an icon for each device in the
TV's Input Selection menu and can also send information
from any IEEE 1394 device to other compatible devices.
A/V Disc
Digital
VCR
TV
Hub Connection
Method
The IEEE 1394 standard allows you to use the TV as a hub
within the audio/video network. Each device can send
information, which may include audio and video, to any
other device in the network.
A/V
Disc #1
Digital
VCR #2
1394
Monitor
TV
A/V Disc #2
Digital
VCR #1
Chapter
•
IEEE
1394 Devices
Do not loop the last
device in the chain back
to the TV. When the
device chain is looped,
the TV may not be able
to work with the other
devices.
D_g_a_
IEEE 1394 Amplifiers
You can use the TV to control switching between the TV
speakers and speakers connected to your IEEE 1394
amplifier.
1.
TV
Place devices with the slowest communication speed
at the end of the chain. Sometimes the communication speed is marked near the IEEE 1394 connector
with an "S" number. The higher the number, the faster
the communication speed. This TV has a communication speed of s400. Devices with slow communication speeds can interfere with IEEE 1394 signals from
faster devices. When setting up a digital recording
between a faster device and a slower device, make
the slower device the source and make the faster
device the recorder.
Use IEEE 1394 cables 15 feet or less in length
between devices.
This TV is an IEEE 1394a device.
Press INPUT
to open the Input Selection menu. The
screen will show an icon for a connected IEEE 1394
amplifier.
Place devices that have only a mechanical (two-position) power switch at the end of the chain or leave the
power switch in the on position. When turned off,
IEEE 1394 signals may not be able to pass through the
device to other devices.
It can be used with
an IEEE 1394b system when an IEEE-1394a-to-1394b
convertor is used. 1394b systems are capable of
greater distances and multi-room applications.
The TV can recognize a maximum of five IEEE 1394
devices.
IEEE 1394 Devices
Menu
81
that has sub-units, a pop-up menu will appear to allow
you to select the sub-unit you wish to use.
Overview, continued
Tips for Connecting
7. Using IEEE 1394 Devices
See the Input Selection menu, figure 3.
2.
Press AUDIO
to move the highlight to the audio section.
3.
Press 4 _ to select either the TV speakers or the IEEE
1394 amplifier.
Press ENTER
to select and hear the new audio source.
4.
IEEE 1394 Camcorders
Control
Functions.
Connect the camcorder to the
TV's IEEE 1394 jack on the rear of the TV and test
using the TV's remote control to operate the camcorder. If your model does not operate properly, use
the camcorder's control buttons instead.
MPEG Camcorder.
If you are unable to play back
over the IEEE 1394 interface, use the analog audio/
video connections described in chapter 2, "TV Connections."
DV Camcorder.
Connect the camcorder using the
analog audio and video connections described in
chapter 2, "TV Connections."
TV Back Panel
and the input Selection
Select an IEEE 1394 device to watch from the Input Selection menu just as you would any other device. See figure
3, Input Selection menu.
When you connect an IEEE 1394 device to the TV network
and power it on, the new device is automatically detected.
Some non-audio/video or incompatible IEEE 1394
devices, such as personal computers (PCs), may not be
detected by the TV and do not appear in the Input Selection menu. Such devices can, however, coexist and are
still available to other devices on the IEEE 1394 network
that are compatible with these non-audio/video devices.
You can connect an IEEE 1394 camcorder
Some devices may be a combination of two or more types
of devices, such as a recording device that is also a tuning
device. Each portion of the device is called a sub-unit.
When you select a device on the Input Selection menu
with an IEEE
1394 cable or with analog audio/video cables. In either
case, test using the TV's remote control to operate the
camcorder over the IEEE 1394 cable.
82
Chapter
7. Using IEEE 1394 Devices
Record To. If you have more than one recordable
IEEE 1394 device connected, use A Y to select it
from the list in the Record To box.
Duration.
Use A V to select a recording duration of from 30 minutes to six hours in 30-minute
increments. The default is one hour.
Recording to IEEE 1394 Recordable
Devices
You can use the TV to control recording to IEEE 1394
devices. While recording, you can view a program on a
different input or power off the TV. The following table
lets you see what signals can be recorded to an IEEE 1394
digital VCR or A/V disc.
Can be
recorded
Digital channels,
including high-definition channels
ANT
Digital signals, includ-
IEEE 1394 devices
3_
ANT
Summary of signal inputs and recording
digital VCR or A/V disc.
2.
Press (_
3.
Review the recording setup information. To change
the source, recording device, or duration, follow the
steps described above under "Recording Now."
4.
Specify when to start the recording.
Start Time
a. With the hour highlighted in gold characters,
press A Y to select the hour, including AM or
PM. Press ENTER
to move the highlight to the
minutes.
b. With the minutes highlighted, press A T to
select the minutes.
Day. Use A V to select a day of the week.
1
to an IEEE 1394
5_
There are two ways to record digital content to an IEEE
1394 recordable A/V disc or DVCR:
•
From the TV's Recording Setup menu
From the TV's ChannelView
immediate
Recording
Setup Menu
from
TM
channel guide
Now from
1.
{RECORD)
to open the Recording Setup menu.
Press (_
the Menu
{RECORD)
to open the Recording Setup menu.
Select Add and press ENTER
to add the recording to
the Record List. A confirmation message will be
displayed if your selection is successful. If you pick
overlapping times, day(s), or destination devices, you
will see a message stating there is a conflict.
6.
While the Recording Setup menu is displayed, press
GUIDE
to view a list of scheduled recordings and verify
the addition of the recording to the Record List, figure
2.
7.
From the Record List you can:
Press GUIDE
to return to the Recording Setup menu.
Press EXffto return to TV viewing,
the Recording
Recording
from the Menu
Ensure that TV Energy Mode is set to Fast Power On
and the TV clock is set to the correct time and day.
See "Setup Menu" to make changes.
1, ANT 2
iNPUT 1-3,
COMPONENT
and 2
Recording
1.
,i
Cannot be Analog channels
recorded
Analog signals
a second time to start recording.
Time=Delayed
1, ANT 2
ing high-definition
signals
Press _
Figure 1. The Recording Setup menu
Review the recording setup information. Move the
highlight to each box you need to change.
With the leftmost icon highlighted (the source),
press A Y to change the source input if needed.
Channel. If the source is an antenna, select a
memorized digital channel using A T, CHi_/V,
or
enter the channel number from the remote control.
Figure 2. Record List screen. From the Record menu,
press GUIDE to open the Record List to review or cancel
scheduled recordings.
Chapter
Recording to IEEE 1394 Recordable
Devices, continued
Recording
Guide
from
the ChannelView
TM
Channel
ChanneIView provides program listings, as sent by the
broadcasters, for memorized channels on ANT 1 and
ANT 2. Press the GUIDE
key while watching ANT I or
ANT 2 to view ChannelView listings and to set up immediate or future recordings as described here.
Immediate
Recording
from ChannelView
1.
Press INPUT
to open the Input Selection menu. Highlight an ANT 1 or ANT 2 program source and press
ENTER.
2.
Press GUIDE
to open the ChannelView channel guide for
the current input.
3.
Use A Y to highlight the channel and program you
wish to record from the list of channels.
4.
Press(_
(RECORD}.
A red "R" temporarily displays next to the program
listing to indicate the program will be recorded.
5.
Press EXITto return to TV viewing.
Time=Delayed
Recording
7. Using IEEE 1394 Devices
Cancelling
Recordings
To Cancel
a Recording
83
in Progress
1.
Press INPUT
to open the Input Selection menu.
2.
Move the highlight to the source input icon. There is
no need to press ENTER.
The Input Selection menu displays an icon for an
active recording connection to a recordable IEEE 1394
device. See the IEEE 1394 connection icon in figure 3.
3.
Press CANCEL.
The connection icon will disappear to
indicate termination of the recording connection.
4.
Press EXITtoreturn to TV viewing.
Connection
Icon
Audio
from ChannelView
Set Up the Recording
1.
Ensure that TV Energy Mode is set to Fast Power On
and the TV clock is set to the correct time and day.
See "Setup Menu" in chapter 4, "TV Menu Settings."
2.
Perform steps 1 and 2 described above.
3
Press A Y to highlight the source channel you wish to
record from.
4.
Press _" to view a list of future programs on that
channel.
5.
Press A. Y to highlight a future program.
6.
Press(_
(RECORD}.
A red "R" temporarily displays next to the program
listing to indicate the program will be recorded.
You can schedule a maximum of 32 recordings.
Press EXITto close the menu.
7.
Confirm the Recording Setup
1.
Press (_
(RECORD}
to open the Record menu.
2.
Press GUIDE
to open the Record List (figure 2) and view
all scheduled recordings. Press OHb,/V
to page
quickly through the list.
3.
Verify that the program you wish to record appears in
the list.
4.
Press EXITto close the menu.
Figure 3. The Input Selection menu displays specialized
icons for IEEE 1394 devices. The audio icons are
displayed only when an IEEE 1394 ampfifier is connected.
To Cancel
a Scheduled
Recording
1.
Press _
2.
Press GUIDE
to open the Record List (figure 2) and view
all scheduled recordings. Press ON/_/V to page
quickly through the list.
3.
Highlight the program you wish to remove from the
Record List and press CANCEL.
Press EXITto close the menu.
4.
(RECORD}
to open the Record menu.
84
Chapter
7. Using IEEE 1394 Devices
The TV Remote Control and IEEE
1394 Devices
•
To Power On or Off a Compatible
Device
For compatible satellite receivers and some cable
boxes, the TV remote control GUIDE
key displays the
on-screen programming guide for the receiver or cable
box. Press A Y 4 _" and ENTER
to navigate the displayed program guide.
IEEE 1394
1.
Press INPUT
to open the Input Selection menu.
2.
Move the highlight to the icon for the device.
no need to press ENTER.
3.
Press POWER.
4.
Press EXITto return to TV viewing.
For satellite receivers, you may also be able to use the
numbers or other additional buttons.
For an IEEE 1394 cable box or satellite receiver, you
can also try using the CABLE/SAT
position of the TV
remote control to see if it can operate the device. If
not, use the remote control that came with the device.
Operation
(slide switch
POWER
of IEEE 1394 Devices
with
the TV's Remote
Control
set to TV position)
Power the device on/off when highlighted
in the Input selection
menu. See the instructions
Mute On/Off
MUTE
when followed by ENTER)
EXiT
CANCEL
Exit menus/displays
Cancel function or counter
reset
Cancel function
Delete recording from Track List
Up/down/left/right
playback
Sktp Backwards 12 seconds dunng
playback
"
Up/down/left/right
Skip to end or beginning of program
Up/down in track list
GUIDE
A V 4 _
above.
PLAY
Play
Play
(_
REV
Reverse picture scan or Slow Play ' Reverse or Slow Play
(_
FFWD
Fast picture
(_
PAUSE
Pause
scan
or Fast Play
Fast
Play
Pause
There is
Chapter
A/V Discs
A/V Disc Track
Retention
List Screen
When viewing an A/V Disc:
•
•
•
=
7. Using IEEE 1394 Devices
Press GUIDE
to display its Track List (see figure below).
Press A or V to navigate through the Track List.
To play a track, select it on the list, then press ENTER.
Press INFO
to view details for a highlighted track.
To move through listings quickly, press PAGE/k/V.
To delete a track, highlight it and press CANCEL.
85
Period
Some COPY NEVER tracks have a retention period
assigned by the content provider. The retention period
is the length of time you can keep and view the recording. The initial retention period, if any, is shown next to
the copy status in the Track List INFO
display (see figure 4).
To check how much time remains of the retention period,
start viewing the recording and press INFO.
Note:
The retention period for all tracks on the disc
expires if there is any loss of power to the TV, even
momentary. For example, expiration of the retention period will occur if you:
Unplug the TV from the AC power source.
Experience a power outage or power
fluctuation.
Remember that you can safely turn off TV power
using the POWER
button without affecting the retention period.
To Copy a Track to Another
IEEE 1394 Device
1.
Press INPUT
on the remote control and press A Y 4 I_
to select the source A/V disc. Press ENTER
to open the
Track List.
Figure 4. A/V Disc Track List screen
2.
Press A or Y to select a track. Then press ENTER
to
start playback.
A/V Disc Search
3.
Press (_
4.
Press (_ (RECORD}
on the TV remote. The Record
menu will display.
5.
In the Record To section, review the destination
device (A/V Disc, DVCR). Change if necessary. If
moving, leave the other settings unchanged.
6.
Press _
by Time
While playing an IEEE 1394 A/V disc you can search to a
specific time in the recording.
1.
Start playing the desired track on the A/V disc.
2.
Use the number buttons to enter the time code position of hours followed by minutes. For example, to
enter one hour and twenty-two minutes (1:22) into the
track, enter 1, 2, 2.
3.
Press ENTER
to skip to the time code position. To
cancel the request or to start over, press CANCEL
instead of ENTER.
Copying
A/V Disc Recordings
Tracks you record to disc may have copy restrictions
assigned to them. To learn a track's copy status, highlight the track in the Track List and press INFO.Tracks are
assigned one of these ratings:
(or no status shown)
Copy Never
il
The track cannot be transferred to
another recording device. Tracks
of this type may have an assigned
retention period. See below for
more information.
i
(PAUSE}
to pause playback.
a second time to start recording.
86
Chapter
7. Using IEEE 1394 Devices
Switching Between Analog and
Digital IEEE 1394 Outputs
To enable switching between analog and digital outputs,
you must have check marked the Analog Connection
box when the New 1394 Device screen displayed when
you first connected the device. See the section "Before
You Begin" in chapter 2, "TV Connections."
Figure 5. The ClearThought Auto Input sensing screen
for IEEE 1394 devices. Place a check in the Analog
Connection box if your device has both analog and digital
outputs.
1.
Press INPUT
to display the Input Selection menu.
2.
Highlight the icon for the IEEE 1394 device.
3.
Press A Y to switch between icons representing the
analog and digital outputs of the device. See figure
6.
Figure 6. The Input Selection menu shows icons for the
analog and d_gital outputs of the IEEE 1394 device.
4.
Press ENTER
to select the device output.
Appendices
Appendix
Appendix
A: Bypassing the Parental Lock .................
B: Specifications ............................
89
91
Appendix
Appendix
C: Lamp Cartridge
D: Troubleshooting
93
95
Replacement .................
..........................
[
Appendices
89
|
Appendix A: Bypassing
Parental Lock
the
Bypassing
the Parental
Lock
After you set the lock, you must use your pass code to
view a locked program, view the locked TV, cancel the
lock, or enter the Parental Lock menus.
_F
If you forget your pass code, you can view the locked
TV without entering your pass code. When you are
prompted for your pass code, press the number 9 and OV
buttons on the TV remote control at the same time. This
c
0
o
W
process temporarily
0
When entering the Parental Lock menu, this process
deletes your old pass code and prompts you to enter a
new pass code. Press EXITto exit the menu.
•
unlocks the TV
0
0
C
0
_m
0
the Front
Button
Lock
Press and hold the MENUbutton on the TV front panel for
over eight seconds. If the TV is off, this action turns it on.
Z
<
0
W
0
0
mm
m
0
o_
0
F_
,.e an_il_ bypass
__
asafe
reference.
place for future
Appendices
91
Appendix B: Specifications
Projection System
DLP, 0.65" chip, 1920 x 1080 pixels with Smooth Picture
i
Channel
Frequency Reception
TM
150-watt VlP type
Over-the-Air: VHF 2-13, UHF 14-69
Analog Cable: 1-125
Over the Air:
Cable:
Analog NTSC, Digital ATSC with sub-channels
formats)
Analog NTSC (non-scrambled)
Digital QAM 64 and 256 with sub-channels
Channel Type*
(all 18 video
(non-scrambled)
CableCARDTM:
(WD-52731,
WD-65731)
i
Authorized scrambled
and non-scrambled
digital channels
* Note for Digital Channels: The channel numbers displayedon screen are determined by the broadcasteror cable company and can
vary from the standard frequency number. If there is no channel-numberinformation providedby the broadcaster or cable company,the
i
TV createsa channel number. The created channel number uses the frequency numberas the main channelnumber and the program
numberas the sub-channel number. When using an authorized CableCARD,the channelnumbers are determined by the cable company.
Antenna/Cable
input
2
RF
F connector, 75-ohm
...............................................................................................................................................
connector ....................................................
HDMI EIA-861B standard for digital audio
and video
Component
Video (WPr/Pb)
EIA-770.1 & EIA 770.2
480i, 480p, EIA 770.3
720p and 1080i (video
standards)
Video:
Audio:
60 Hz: 480i, 480p, 720p, 1080i
24 Hz, 30 Hz, 60 Hz: 1080p
PCM stereo
RCA Pin Plug (EIA-770.3 Standard Levels and
Timing)
Y:
1.0 Vp-p (includes sync), 75-ohm
Pr:
700 mV p-p, 75-ohm
Pb:
700 mV p-p, 75-ohm
92
Appendices
Appendix B: Specifications, continued
Video
Video: RCA Pin Plug 1.0 Vp-p, 75-ohm
ignal Type: NTSC 480i only
Vrms + 0.5 Vrms (full scale) for digital sources.
JEEE 1394 System Compatibility
•
This television is designed to conform to IEEE 1394 AV/C Software standards in effect at the time of development.
This networking and control technology is designed to provide high-performance digital connections and product
control, making the product easier to use.
Mitsubishi D-VHS VCRs are fully compatible with this TV in audio, video, and control.
As other manufacturers distribute products that use the IEEE 1394 AV/C standards, they will be responsible for
developing products that meet the standards of the technology, as well as compatibility testing with other products.
Mitsubishi cannot be responsible for their efforts, and therefore cannot promise compatibility with these other products. Any compatibility problems with other manufacturers' products should be brought to the attention of those
manufacturers.
HDMJ
The HDMI input is compliant with EIA-861B standards for standard, extended, and high-definition video; digital audio,
and HDCP copy protection. The HDMI inputs on this TV are not intended for use with personal computers or devices
outputting video signals with computer resolutions.
Appendices
93
Appendix C: Lamp Cartridge Replacement
A
BURN DANGER!
During normal operation, the surfaces
the TV near the lamp are extremely
inside
hot.
TOUCH THE LAMP CARTRIDGE BY THE HANDLE ONLY
Do not touch the glass parts of the lamp cartridge.
CAUTION:
if the television
is on, press POWER
it to cool for at least one hour before attempting
to turn it off. Unplug the television
to replace the lamp cartridge.
and allow
Lamp Life
The light source for this television is a lamp, which is part of a lamp cartridge assembly. The life of the lamp can vary,
based on the lamp itself, the air temperature around the TV while it is operating, and your viewing patterns. Warmer air
or poor ventilation shorten the lamp life, as does turning the television on and off frequently. Mitsubishi warrants the
lamp for one (1) year from the date of original purchase at retail. It is likely that the lamp will last much longer than this.
Order a new lamp when the TV picture becomes
hand before the existing lamp fails.
To Order
noticeably
dimmer.
It is best to have a replacement
lamp on
A New Lamp
While Under Warranty
After Warranty
Call (800) 553-7278. Please have model number, serial
number, and TV purchase date available,
Visit our website at www.mitsuparts.com
or
call (800) 553-7278. Order lamp part number
915P049010.
WARNING
=
Do not remove the lamp cartridge immediately after turning off the television. You may get burned because the
lamp is very hot. Allow the television to cool for at least one hour before replacing the lamp cartridge.
•
Do not remove the lamp cartridge except when replacing it. Careless treatment can result in injury or fire.
•
Do not touch the lamp glass element.
•
Be sure not to insert any metal or flammable object into the lamp cartridge opening, as it may cause fire or electrical shock. If a foreign object is inserted into the opening, unplug the AC cord of the TV and contact your dealer for
service.
•
Install the lamp cartridge securely.
•
Do not touch the lamp glass elements.
= MERCURY
It may be very hot and break, causing injuries or burns.
Failure to do so may cause a fire.
Oils from your fingers may cause premature lamp failure.
THE LAMP INSIDE THIS PRODUCT CONTAINS MERCURY AND MUST BE RECYCLED OR
DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance at
www.eiae.org
94
Appendices
Appendix C: Lamp Cartridge Replacement, continued
WARNING
THE COVER IS PROVIDED WITH AN INTERLOCK TO
REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET
RADIATION. DO NOT DEFEAT ITS PURPOSE
OR ATTEMPT TO SERVICE THE TV WITHOUT
REMOVING THE COVER COMPLETELY.
Removing
Figure 1.
Handle
(step 5)
the Old Lamp Cartridge
1. Turn off TV power and allow the lamp to cool at least
one hour before proceeding.
After the lamp has cooled, remove the cover. Refer
to figure 1. Use a #2 (large) Phillips screwdriver to
remove the two screws securing the cover. Keep the
screws and cover for re-installation
3. With a large flat-blade screwdriver, loosen the two
shiny screws securing the lamp cartridge until they
disengage from the mating threads. These are captive
screws and cannot be separated from the lamp cartridge.
Figure 2
4. Fully open up the bag supplied with the replacement
lamp and set the opened bag aside.
5. Gently grasp the handle of the lamp cartridge and pull
the old cartridge straight out. See figures 1 and 2.
CAUTION: Do not tilt or rotate the cartridge, as
small glass fragments may fall out.
6. Without tilting or putting down the lamp cartridge,
insert it into the opened bag. Close the bag while
being careful not to let any glass particles fall out.
Installing
b.
Hold the lamp cartridge level with the lamp
compartment, oriented as shown in figure 5.
c.
Align the grooves on the cartridge with the top
and bottom guides in the lamp compartment.
See figure 5.
d.
Carefully push in the cartridge until it is fully
seated. If the cartridge does not slide in
smoothly, gently wiggle the handle from side to
side while pushing in.
--
the New Lamp Cartridge
Guide in lamp
compartment
1. Do not touch the glass parts of the new lamp cartridge. Insert the new cartridge into the TV using the
following guidelines:
a.
Refer to figures 3 and 4 and note the location of
the top and bottom guides inside the lamp compartment and the corresponding grooves on the
top and underside of the lamp.
Figure 5
2_
With either your fingers or the screwdriver, gently
tighten the two shiny screws. If using a screwdriver,
use only two fingers for final tightening. AVOID
OVERTIGHTENING!
3_
Replace the plastic cover and retaining screws.
Guides inside the
lamp compartment
4. WASH YOUR HANDS THOROUGHLY, AS THIS
LAMP CONTAINS MERCURY.
Disposal
Figure 4
.....y
Figure
3
Grooves are on the top and
underside of the lamp cartridge
of the Old Lamp Cartridge
Contact your local authorities or the Electronic Industries Alliance at www.eiae.com for lamp-disposal or
recycling instructions. Do not dispose of the old lamp
with common trash.
Appendices
Appendix
System
D: Troubleshooting
Reset Button
Service
If the TV does not respond to the remote control, front
panel controls, or will not power on/off, press the
SYSTEM
RESET
button on the front panel with a pointed object,
such as the point of a pencil or end tip of a paperclip.
Service
The green LED will flash quickly for about one minute.
When the green LED stops flashing, you may turn on the
TV. The changes you made most recently, before using
SYSTEM
RESET,
may be lost. Changes you made previously,
however, are not lost.
•
TV Reset Menu
1.
Select any device from the Input Selection menu.
2.
Press MENU
followed by 123 to open the Reset Service
Menu. CAUTION: All settings except V-Chip will be
reset to the original factory defaults
Read on-screen
warnings
before proceeding, as some user data or settings
may be
erased.
3.
Press ENTER
to reset TV defaults.
Demo
Mode
This TV has a demo mode for use in retail stores. To turn
off demo mode:
1.
Press MENU.
2.
When the Main menu appears with Setup highlighted,
press ENTER.
When the Setup menu opens, press b"to highlight the
on-screen Demo Mode Off button.
Press ENTER.
3.
4.
95
and Support
If you are unable to correct a problem with your TV,
consult your Mitsubishi dealer or a Mitsubishi Authorized
Warranty Service Center.
DO NOT adjust any controls other than those
described in this Owner's Guide.
DO NOT remove the protective back cover of your TV.
Menus not described and shown in this Owner's Guide
are designed for factory use and for authorized service
personnel. Damage caused to the TV by unauthorized
changes or changes to these menus made by unauthorized persons are not covered under warranty.
Support
To order replacement or additional remote controls,
lamp cartridges, or Owner's Guides, visit our website
at www.mitsuparts.com
or call (800) 553-7278.
For questions:
•
call Consumer Relations at 800-332-2119.
•
E-mail:
[email protected]
•
Website: www.mitsubishi-tv.com
96
Appendices
Appendix
D:
Troubleshooting,
continued
General TV Operation
Symptom
Remarks
1.
A fan is running even while the TV is powered
off.
Normal TV operation. When the TV is off, internal components
continue to draw power and must be cooled by the fan.
2.
The TV remote control does not work.
•
3.
TV does not respond to the remote control or
to front panel control and TV will not power
on or off.
Use the System Reset button.
4.
When a device is selected from the Input
Selection menu, the screen is blue (no signal
•
=
Check that the batteries are installed correctly.
Check that the slide switch is set to TV.
Be no more than 20 feet from the TV when using the remote control.
Program the remote control to operate the TV or other device
(see chapter 5).
Make sure the selected device is turned on.
Begin play of the VCR.
source).
5.
Devices are grayed out in the Input Selection menu or the Split Screen Input Selection
A recording is in progress.
device.
Cancel the recording to select the
menu.
Digital channels, IEEE 1394 digital devices, and PCs cannot
display in the Split Screen sub-picture.
6.
You have forgotten your Parental Lock pass code. See Appendix A, Bypassing the Parental Lock.
7.
Rating restrictions are not working.
Open the Parental Lock menu and:
Verify that the U.S. Ratings or Other Ratings setting is On.
Check the Lock Time/Unlock Time to check if rating restrictions are disabled.
Rating restrictions apply only to content on ANT 1 and ANT 2,
INPUT 1-3, and IEEE 1394 inputs.
8.
On-screen displays appear each time you
change a function.
Normal TV operation.
9.
Cable provider needs information to start
CableCARD TM service.
On the remote control, press MENU and then enter the numbers
999 to display the Host ID and CableCARD TM ID information.
TV Channels
Symptom
Remarks
1.
The TV takes several seconds to respond to
channel changes.
•
2.
You cannot access a channel.
It is normal for digital channels to take longer to tune in.
Press ENTER after a channel number to avoid delays.
Use a 4-digit number for an over-the-air digital channel.
Use a 6-digit number for digital cable channels if your cable
service is able to recognize 6-digit channel numbers.
Use number keys instead of CH/_/V.
Be sure the channel you want to view is in memory. See
"Channel Menu" in chapter 4, "TV Menu Settings."
Check that the TV is turned to the correct device or antenna
for that channel by pressing the INPUT button.
Make sure the Parental Lock is off.
If you cannot tune to a virtual digital channel even though
the TV has already memorized digital channels, tune to the
actual channel number used by the broadcaster. The virtual
channel will then be automatically added to memory.
3.
Name options are not available for some
channels.
Only memorized analog channels can be named.
4.
When ChannelView TM list is displayed, information appears incomplete
Available information is sent from the broadcaster or cable provider. No other data is available.
Appendices
Appendix
D:
Troubleshooting,
97
continued
TV Power On/Off
1.
Symptom
Remarks
TV takes an excessively long time to power
•
On.
•
When switched on, the TV needs time to boot up, just as a
computer does. The TV's lamp also requires a few moments
to heat up to full brightness.
TV Energy Mode is set to Low Power. To change TV Energy
Mode to Fast Power On: Press MENU, open the Setup menu,
highlight the Fast Power On radio button, press ENTER.
You cannot program the TV to turn on automatically (Timer function)
•
3_
The TV will not turn on after being plugged
in.
If green light on front panel is blinking, wait for at least one minute
for the light to turn off, then press POWER again.
4.
TV turned itself off and the light on the front
panel started to blink.
•
TheTV may be locked.
The clock may not be set.
A time-delayed recording may have started.
TV Energy Mode is set to Low Power. Change to Fast Power
On in Setup menu.
Momentary power fluctuation caused the TV to turn off to
prevent damage. Wait for the green light to stop flashing and
turn on again.
If the TV does not stay turned on, use the System Reset
button on the front panel. If this happens frequently, obtain
an AC line power conditioner/surge
protector.
An unusual digital signal may have been received, triggering a
protection circuit. Wait for the light to stop flashing and turn TV
On.
5
TV will not power off.
Use the System Reset button.
Picture
Symptom
Remarks
1.
Picture does not look like a high-definition
picture,
Not all signals are high-definition signals. To receive high-definition programming from your cable or satellite provider, you must
subscribe to the provider's high-definition service. Some overthe-air broadcasts are in high-definition and can be received with
a high-quality antenna suited to your location.
2.
Picture is getting dimmer over time.
The lamp is nearing the end of its life. Order a new lamp soon.
See Appendix C for ordering information and replacement
instructions.
3.
Split Screen does not display a sub-picture.
•
4.
CableCARD channel is not shown as Split
Screen sub-picture when CableCARD
channel is the main image.
CableCARD allows only one channel at a time to be used.
5.
There is a large black or gray rectangle on
the screen,
The TV's analog closed captioning has been set to "text" mode in
the Captions menu. Turn off because there is no text information
being broadcast.
6.
You cannot view a picture when playing a
VHS tape.
Check your VCR's owner's guide for further troubleshooting.
7.
VCR or DVD player's on-screen menus jitter
up and down.
Possible cause: Many VCRs and DVD players provide on-screen
menus at only half-resolution.
These lower-resolution graphics
may appear to jitter up and down when the TV converts them to
high-definition graphics.
Make sure the Parental Lock is off.
Not all inputs can be displayed as a sub-picture.
98
Appendices
Appendix
D:
Troubleshooting,
continued
Picture
Symptom
Remarks
8.
When viewing a stopped VCR, white lines
are rolling on the screen.
•
•
9.
Screen is black when trying to view digital
channels or IEEE 1394 device.
The PerfectColor TM color balance has been incorrectly set. Press
VIDEO repeatedly until you see the PerfectColor option and press
ENTER to open the PerfectColor TMmenu.
10.
DVCR analog/digital
If the tape is currently playing but no picture displays, there may
be a mismatch of the media with the display. Press INPUT to
display the Input Selection menu. Press ENTER for the DVCR
device. If digital is selected, try analog, or if analog is selected, try
digital.
problems.
Turn off video mute for the VCR.
Begin playing the tape.
Change the VCR input to the antenna input.
indicators
Symptom
Remarks
1.
Lamp indicator light is a constant red.
Turn the TV off for at least 2 minutes. Turn back on. If light is still
red, the lamp has failed. Replace it. See Appendix C for lamp
replacement information.
2.
Lamp indicator light is a flashing yellow.
Lamp cover door is open or lamp cartridge is not secure. See
Appendix C for lamp replacement information.
3.
Status indicator light is a steady yellow.
Room temperature
4.
Status indicator light is a steady/flashing
red.
Service is required. Contact your dealer or a Mitsubishi Authorized Service Center to arrange for a service evaluation. Listings
of Mitsubishi Authorized Service locations can be obtained from
our web site, www.mitsubishi-tv.com
or by calling 1-800-3322119.
has exceeded proper levels. Cool the room.
Sound
Symptom
Remarks
1.
There is no sound even when the
volume is turned up.
•
•
Check if the MUTE button is on.
The TV's "Listen to:" setting may be set to SAR
Check that the TV Speakers setting is On in the Audio/Video menu.
If using an IEEE 1394 amplifier, check audio source in Input Selection
menu.
2.
The sound does not match the screen
picture.
•
•
The TV's Listen to: setting may be set to SAP.
If using stereo or A/V receiver speakers, check their input selection.
If using stereo or A/V receiver, check that AUDIO OUT LEFT/
RIGHT on TV's back panel is connected to the A/V receiver.
Appendices
Appendix
D:
Troubleshooting,
99
continued
IEEE 1394 Recording
Symptom
Remarks
1.
Program to be recorded was correctly
selected from ChannelView, however, incorrect program was recorded.
The broadcaster supplied program information that was incorrect
and/or was changed after a recording was added to the Record
List.
2.
Incomplete ChannelView program recorded.
Recording device may lack sufficient blank space to make a full
recording.
3.
ChannelView program recording failed.
•
.
Cannot record to or from the IEEE 1394
device, including dubbed recordings.
Connection and compatibility issues with IEEE 1394
(FireWire®) digital devices. This may include too many
Firewire devices in use at one time, or the recording device
not understanding the record command.
Television lost power long enough to lose current clock time.
Analog VCR power was left off.
TV energy Mode was set to Low Power. Change TV Energy
mode to Fast Power On. Press MENU, open the Setup menu,
highlight the Fast Power On radio button, press ENTER.
To initiate a recording to IEEE 1394 device, press the _
(RECORD) key. The Record menu displays allowing setup of
the recording.
The source device for the recording is not powered on.
When dubbing, the destination device for the recording is not
powered on.
The wrong medium (analog tape for digital recording, or
digital tape for the analog recording) is in the device.
The program is copy protected.
The program has already been recorded once and the copy
protection only allows one recording.
Unapproved source device for copy protected material.
The recording device can not decode the copyright signal
included in the signal source (try another device if available).
The playing device (for dubbing) does not support copyrighted material.
Source for recording is copyrighted
Too many IEEE 1394 devices in network. Insufficient bandwidth available. Disconnect unused devices.
Source Device has higher speed (S 400) than record device.
If possible, reverse devices, play in the slower device and
record in the faster device.
IEEE 1394 Devices
Symptom
Remarks
1.
Excessive digital artifacts appear when
viewing an IEEE 1394 device,
•
2.
D-VHS recordings for digital cable have
drop-outs (loss of picture or sound), or no
playback.
Digital cable signals on IEEE 1394 can exceed the data rate standards supported by DVCR.
The IEEE 1394 cable is too long; 15 feet between devices is
the maximum.
There may be a slow device in the middle of the IEEE 1394
network. Move the slow devices to the end so that connections for faster devices do not pass through them.
1 O0
Appendices
Appendix D: Troubleshooting, continued
IEEE 1394 Devices
Symptom
Remarks
3.
There is no audio and video from the IEEE
1394 device.
=
•
4.
The IEEE 1394 Device is no longer listed in
the Input Selection menu.
5.
The IEEE 1394 device cannot be selected (is
grayed out).
The device may be busy with a recording.
6.
MENU button does not display a menu.
•
The IEEE 1394 device does not provide a menu.
The TV cannot support IEEE 1394 menus.
7.
All IEEE 1394 devices disappear.
•
The connected devices must not be in a loop that returns to
the TV. Make sure a device is connected at the end.
The device is not turned on. Turn the device power on.
No media (tape or disc) is inserted into the device.
The media is blank (has no recording).
The play command failed - Try pressing play again on the
device's remote control or front panel.
The device is already in use (for example, the device is currently recording).
The source is copy-protected or violates copy protection.
The device's digital video signal is not supported by the TV,
as may be the case with an IEEE 1394 signal from a computer. Use analog connections instead, if available.
The device is not an audio/video device.
Too many other devices are already communicating over IEEE
1394. Remove or stop some devices and try again.
The
The
The
The
IEEE 1394 plug is disconnected or loose.
IEEE 1394 device has not been powered on. Turn on.
device has not been discovered.
device is not an audio/video device
Cancel the recording.
Disconnect all the cables and devices from the TV. Replace
them one by one to locate the problem device or cable.
Use System Reset (front control panel).
8.
Cannot rediscover a deleted IEEE 1394
device.
9.
An IEEE 1394 device has been plugged in
but does not appear in the Input Selection
menu (not discovered).
10.
Cannot view video from an IEEE 1394 DV
camcorder.
11. An IEEE 1394 device is not responding
properly.
The device has been disconnected.
Plug it in.
The IEEE 1394 connection to the TV or another device is not
secure or is loose.
The IEEE 1394 device is not powered on.
A device in the IEEE 1394 chain is not powered on. Turn on
all the devices.
The device discovery can take as long as a minute to initiate.
IEEE 1394 cable is too long (maximum of 15 feet between
devices).
The IEEE 1394 device uses an incompatible protocol and will
not be discovered
Use analog connections for video and audio. You can still use the
IEEE 1394 connection for control functions, however.
Unplug the device's power cord. Wait at least ten seconds
and plug it in again.
Some IEEE 1394 devices are not supported by the TV
because of incompatible standards.
Trademark
and License
Information
101
Trademark and License information
LICENSOR'S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY EXPRESS,
IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS, INCLUDING, BUT
NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
CableCARD
is a trademark
TM
CompactFlash®
and CF are trademarks of the CompactFlash
DCR TM Certification
Inc.
Association.
Logo is a trademark of the Consumer Electronics Association.
Digital Light Processing
Manufactured
of Cable Television Laboratories,
TM
and DLP TM are trademarks
under license from Dolby Laboratories.
DTVLink TM Certification
Firewire® is a trademark
of Texas Instruments.
Dolby is a trademark of Dolby Laboratories.
Logo is a trademark of the Consumer Electronics Association.
of Apple Computer, Inc. registered in the U.S. and other countries.
HDMF Mthe HDMI logo and High-Definition
Licensing LLC.
Lifestyle® 28 is a trademark
Multimedia Interface are trademarks or registered trademarks of HDMI
of the Bose Corporation.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home
and other limited pay-per-view uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly prohibited.
This product includes technology
from Microsoft Licensing, Inc.
MultiMediaCard
Playstation®
TM
owned by Microsoft
Corporation and cannot be used or distributed
is trademark of Infineon Technologies and licensed to the MultiMediaCard
without a license
Association.
2 is a trademark of the Sony Corporation.
The Simplay/./D
logo and the words "Simplay TM''and "Simplay HD TM''are the trademarks of Silicon Image, Inc.
XBox TM iS a trademark of the Microsoft Corporation.
ChannelView TM, ClearThought®, Diamond Shield TM, MediaCommand TM, NetCommand®,
QuickView TM, ViewPoint® are trademarks of Mitsubishi Digital Electronics America, Inc.
MonitorLink
TM,
PerfectColor
TM,
102
Trademark
and License
Information
Mitsubishi TV Software
END-USER
LICENSE AGREEMENT
FOR EMBEDDED
SOFTWARE
iMPORTANT
- READ CAREFULLY:
This License Agreement
is a legal agreement between you (either an individual or an entity) and
Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television ("Software").
By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
The Software
and treaties.
1.
is protected
by United States copyright
The Software is licensed, not sold.
LICENSE
GRANT.
MDEA grants you a non-exclusive,
only with the Mitsubishi
television model that included
2.
RIGHTS AND LIMITATIONS.
Software
Software
laws and international
non-transferable,
this owner's
Not for Resale. You may not resell or otherwise
has been pre installed.
treaty
transfer
provisions,
as well as other intellectual
property
laws
limited right and license to use one copy of the Software
guide and owned
by you.
for value the Software,
except
in conjunction
with a sale of the TV that
Prohibition
on Reverse Engineering,
Decompilation
and Disassembly.
The Software contains trade secrets or other proprietary
material
in its human perceivable form and to protect them, you may not reverse engineer, decompile, or disassemble,
or otherwise reduce the
Software to any human perceivable form, except to the extent that the foregoing restriction
is expressly prohibited by applicable law.
Separation of Components.
than one TV.
No Rental.
Trademarks.
The Software
is licensed
You may not rent, lease, lend, or sublicense
This License Agreement
as a single product.
Its component
parts
may not be separated
for use on more
the Software.
does not grant you any rights to any trademarks
of MDEA.
3.
VIOLATIONS.
You understand
that any use, copying or transfer of the Software, except as permitted
pursuant to this License, may
subject you to serious criminal and civil penalties including damages and an award to MDEA of attorneys' fees in connection
with any
violation of this License. You further understand
that you may be held legally responsible
for any copyright infringement
or other violation
of intellectual
property rights that is caused, encouraged,
or induced by your failure to abide by the terms of the License. This license
is effective until terminated,
and will terminate immediately
without notice from MDEA or judicial resolution if you fail to comply with any
provision of this License.
4.
COPYRIGHT.
All title and intellectual
property rights in and to the Software (including but not limited to any images, photographs,
animations,
video, audio, music, text, and "applets" incorporated
into the Software), and any accompanying
printed materials are
owned by or licensed to MDEA. All title and intellectual property rights in and to the content which may be accessed through use of the
Software is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws
and treaties. This License Agreement
grants you no rights to use such content, except that you own the media on which the Software is
recorded, but MDEA and its licensors retain ownership of the Software itself. All rights not expressly granted are reserved by MDEA.
5.
EXPORT RESTRICTIONS.
MDEA is licensing the Software for use within the United States. You agree that you will not export
or re-export the Software.
You specifically
agree not to export or re-export the Software: (i) to any country to which the U.S. has
embargoed
or restricted the export of goods or services, which currently include, but are not necessarily limited to Cuba, Iran, Iraq,
Libya, North Korea, Sudan, and Syria, or to any national of any such country, wherever located, who intends to transmit or transport the
Software back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Software in the design,
development,
or production
of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from
participating
in U.S. export transactions
by any federal agency of the U.S. government.
You warrant and represent that neither the BXA
nor any other U.S. federal agency has suspended,
revoked, or denied your export privileges.
6.
DiSCLAiMER
OF WARRANTY.
EXCEPT
AS OTHERWmSE
PROVIDED
mNTHIS
LICENSE
OR IN THE LIMITED
WARRANTY
APPLICABLE
TO THE TV, MDEA MAKES NO OTHER WARRANTIES
OF ANY KIND WHATSOEVER
REGARDING
THE SOFTWARE
AND HEREBY EXPRESSLY
DISCLAIMS
ALL WARRANTIES
OF ANY KIND WHATSOEVER,
EXPRESS OR IMPLIED, WITH
RESPECT TO THE SOFTWARE.
ALL IMPLIED WARRANTIES,
INCLUDING,
WITHOUT LiMiTATiON,
THE IMPLIED WARRANTIES
OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR
PURPOSE ARE HEREBY EXPRESSLY
DISCLAIMED
BY MDEA. iN
NO EVENT SHALL MDEA BE LIABLE TO YOU OR ANY THIRD PARTIES, IN CONTRACT,
iN TORT OR OTHERWISE,
FOR ANY
DIRECT, iNDiRECT, SPECIAL, iNCiDENTAL
OR CONSEQUENTIAL
DAMAGES OFANY
KiND OR NATURE.
BECAUSE SOME
JURISDICTIONS
DO NOT ALLOW THE EXCLUSION
OR LIMITATION
OF iMPLiED WARRANTIES,
THE ABOVE LiMiTATiON
MAY
NOT APPLY TO YOU.
7.
LIMITATION
OF LIABILITY.
MDEA SHALL NOT, UNDER ANY CIRCUMSTANCES
BE LIABLE TO YOU OR ANY THIRD
PARTIES FOR ANY DAMAGES OF ANY NATURE, WHETHER
iNDIRECT, SPECIAL, iNCIDENTAL,
CONSEQUENTIAL
OR
OTHERWISE,
INCLUDING,
BUT NOT LIMITED TO, ANY CLAIMS FOR LOST PROFITS, LOSS OF GOOD WILL OR EXPENDITURES
MADE OR COMMITTED
FOR iN RELIANCE ON THE CONTiNUATiON
OF THIS LICENSE.
YOU AGREE THAT NEITHER MDEA'S
BREACH OF THIS LICENSE NOR ITS FAILURE TO REPAIR A DEFECT, ERROR OR BUG SHALL CONSTITUTE
A FAILURE OF THE
ESSENTIAL
PURPOSE OF THIS LICENSE.
BECAUSE SOME JURISDiCTiONS
DO NOT ALLOW THE EXCLUSION
OR LiMiTATiON
OF LIABILITY FOR CONSEQUENTIAL
OR INCIDENTAL
DAMAGES, THE ABOVE LIMITATIONS
MAY NOT APPLY TO YOU. MDEA's
liability to you for direct damages for any cause whatsoever
and regardless
of the form of the action, will be limited to the
money paid by you for the TV (based on fair market value of the TV) that caused the damages.
8.
GENERAL.
This License Agreement
will be governed
by the laws of the State of California.
WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects
or other reproductive harm.
103
Mitsubishi DLP TMProjection Television Limited Warranty
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. ("MDEA") warrants as follows to the original purchaser of this
television from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of against defects
arising from improper workmanship and/or material:
a. Parts. The lenticular (i.e. front picture) screen is warranted against defects in materials and workmanship for a
period of thirty (30) days from the date of the original purchase at retail. The lamp and all other parts (except any software incorporated into this television) are warranted for a period of one (1) year from the date of the original purchase at
retail. We will repair or replace, at our option, any defective part without charge for the part. Parts used for replacement
may be replaced with those of like kind and quality and may be new or remanufactured.
Parts used for replacement are
warranted for the remainder of the original warranty period.
b. Embedded Software.
MDEA warrants that all software incorporated into this television set (the "Embedded Software") will perform in accordance with the functional description of Embedded Software in all material respects, but
MDEA does not warrant that the Embedded Software is error-free. MDEA also does not warrant that the Embedded
Software will be compatible under IEEE 1394 AV/C and HAVi software standards with products produced by any other
manufacturer. The limited warranty contained in this section shall continue for a period of one (1) year from the date of
the original purchase at retail. If, after prompt notice within the warranty period, MDEA determines that the Embedded
Software has failed to perform in accordance with such functional description in all material respects and if such failure
is not due to accident, misuse, modification or misapplication of the Embedded Software, then MDEA shall modify or
replace the nonconforming Embedded Software at no charge to you, which at MDEA's sole discretion may be fulfilled
by means of modification or replacement software contained on a replacement memory card for Customer installation.
The foregoing shall be MDEA's sole obligation to you under this limited warranty. All rights under this limited warranty
on the Embedded Software also subject to your acceptance of and compliance with the terms of the Software License
Agreement applicable to this television, and this limited warranty on the Embedded Software shall be null and void if the
Embedded Software is modified or changed in any manner except as specifically authorized by MDEA.
c. Labor. For thirty (30) days after the original purchase at retail, we will repair or replace, at our option, the lenticular
screen if it proves defective. For certain items that are designed to be replaced by the consumer, including (but not
limited to) some Embedded Software, the consumer is solely responsible for any replacement labor. For all other parts,
we will provide the labor for a warranty repair by an authorized MITSUBISHI service center without charge for one (1)
year from the original date of purchase at retail.
d. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within
the applicable warranty time period.
e. This DLP Projection Television uses a single DLP chip to create the screen image. This technology creates the image
using small dots, or picture elements (pixels). Your DLP Projection TV is manufactured to a high level of performance
and quality, in fact, 99.99% perfect in the number of properly functioning pixels. As in other display technology, sometimes a pixel is continuously active, inactive or the incorrect color. Our standard is clear; MDEA warrants only that the
percentage of properly functioning pixels will be not less than 99.99% of all pixels.
BEFORE REQUESTING SERVICE, please review the instruction booklet to insure proper installation and correct
customer control adjustment,
if the problem persists please arrange for warranty service.
1. TO OBTAIN WARRANTY SERVICE:
a. Contact your nearest authorized MITSUBISHI service center, whose name and address can be obtained from your
MITSUBISHI dealer, by writing at the address provided below, calling MDEA at the 800-332-2119, or by using the
support feature of our website at www.Mitsubishi-tv.com.
b. Warranty service will be provided in your home or, if required, at an authorized service shop, provided that your
television is located within the geographic territory customarily covered by an authorized MITSUBISHI service center. If
not, you must either deliver your television to an authorized service location at your own expense, or pay for any travel
and/or transportation costs the service center may charge to and from your home. Actual service labor will be provided
without charge.
c. Proof of purchase date from an authorized MITSUBISHI dealer is required when requesting warranty service. Present
your sales receipt or other document which establishes proof and date of purchase. THE RETURN OF THE OWNER
REGISTRATION CARD IS NOT A CONDITION OF COVERAGE UNDER THIS LIMITED WARRANTY. However, please
return the Owner Registration Card so that we can contact you should a question of safety arise which could affect you.
I04
d. To obtain a replacement lamp during the warranty period, please contact the MDEA Consumer Relations Department
at (800) 332-2119. After the warranty period you may order the lamp directly from the MDEA Parts Department at (800)
553-7278.
2. THIS LIMITED WARRANTY DOES NOT COVER:
a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).
b. Damage to the lenticular screen or Fresnel lens, screen frame, cosmetic damage or to any other damage where such
damage is caused by unauthorized modification, alteration, repairs to or service of the product by anyone other than
an authorized MITSUBISHI service center; physical abuse to or misuse of the product (including any failure to carry
out any maintenance as described in the Owner's Guide including air filter cleaning or any product damaged by excessive physical or electrical stress); any products that have had a serial number or any part thereof altered, defaced or
removed; product use in any manner contrary to the Owner's Guide; freight damage; or any damage caused by acts
of God or other factors beyond the reasonable control of MDEA, such as power surge damage caused by electrical
system or lightning. This limited warranty also excludes service calls where no defect in the product covered under this
warranty is found, service calls related to unsatisfactory audio or visual reception or signal unless caused by a defect in
the product that is covered under this limited warranty, all costs, expenses or any other damages arising from product
installation, or set-ups, any adjustments of user controls (including contrast, brightness, color, tint, fine tuning, sharpness), other adjustment necessary to prepare the unit for display or use, connection with any external audio receiver,
antenna, cable or satellite systems, or service of products purchased or serviced outside the U.S.A. Please consult the
operating instructions contained in the Owner's Guide furnished with the product for information regarding user controls.
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION,
MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY
LIMITED TO A TERM OF ONE YEAR.
4. UNDER NO CIRCUMSTANCES SHALL MDEA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY,
BREACH OF CONTRACT, OR OTHERWISE.
5. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental,
special, or consequential damages, so the above limitations or exclusions may not apply to you.
6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
MITSUBISHI
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Road
Irvine, CA 92618-1904
index
105
index
A
D
A/V Discs 85
Date. See Clock
A/V Memory Reset. See Reset
A/V Receiver
Daylight Savings Time 46
Demo Mode 95
Connecting 31
A/V Reset. See Reset
Digital Audio Out 19
Display Format Definitions 38
Dolby Digital 19, 31, 92
and IEEE 1394 80
DTVLink TM 19
DV 81
DVDs
and the Remote Control 34, 62
and V-Chip Ratings 56
DVD Player with Component Video,
Connecting 31
DVl Device, Connecting 30
DVl Jack (for Personal Computer) 19
Adjust Keys (Up/Down/Left/Right)
34, 44
Anamorphic Picture Format
DVD Definnitions 38
Antenna
Adjusting and the Signal Strength
Meter 49
Connecting 27
Antenna Inputs (ANT l/MAIN, ANT
2/AUX) 18
Audio/Video Menu 45, 57
Audio Settings 58
Auto Input Sensing 22
B
Back Panel (illustrated) 18, 19
Batteries. See Remote Control
C
CableCARD
Cable Box
TM
13, 17, 18, 46
and the Remote Control 34, 62,
84
Connecting 25, 29, 32
IEEE 1394 80
Camcorder
Connecting (Analog) 32
DV (Digital Video) 81,100
IEEE 1394 Camcorders 81
Power 80
Captions Menu 45, 51
Channels. Seealso FAV
and TV Timer 47
Changing 14
Digital Channel Numbers 91
Memorizing 46
Naming 49
Status Display 37
ChannelView TM Channel Listings 36
Channel Menu 45, 49
Cleaning 7
ClearThought® Auto Input Sensing
22
Clock, Set Date and Time 46
Closed Captions. See Captions Menu
Color Adjustments 59
Component Inputs (Y Pb Pr) 19
Computer. See Personal Computer
Connection Types 23
Copy Restrictions 85
and Status Display 37
INFO Key Status Display 37
Input Jacks on TV (Standard Audio/
Video) 18
Input Name Menu 45, 48
L
Lamp Cartridge Replacement 93
LAMP Indicator. See LED Indicator
Lights
Language
Audio Setting (Digital Channels)
58
for TV Menus 46
LED Indicator Lights
LAMP Indicator 16
POWER/TIMER Indicator
STATUS Indicator 16
16
E
Troubleshooting
98
Lock TV. See Parental Lock
Energy Mode 47
Low Power (Energy Mode) 47
F
M
Fan Noise 6
Fast Power On (Energy Mode) 47
FAV 50
Film Mode 57
FireWire®. See IEEE 1394
Freeze Picture. See Pause
Front Panel Lock 53
Memorizing Channels 46
MONITOR OUT Jacks 19
MP3 Audio 80
Mute
Audio
and Closed Captions 51
and status Display 37
MUTE key 34
Video Mute 57
G
GUIDE Key (button) 34
H
N
Noise Reduction (Video) 59
HDMI
HDMI Device 30
HDMI Inputs 12
HDMI Jack, Description 19
Personal Computer with HDMI
Output 75
HDTV Receiver with Component
Video, Connecting 25
HD (High-Definition Signal) 38
I
Icon Order Menu 45, 48
IEEE 1394 Devices
Amplifier Settings 58
and Analog Outputs 22, 86
and Recording 82
and Status Display 37
Compatible IEEE 1394 Devices
80
Connecting
81
IEEE 1394 Devices
Inputs on TV 19
TV Connection Speed 81
P
Parental Lock
Bypassing 89
Front Panel Lock 53
V-Chip Ratings 56
Pass Code
Resetting 89
Setting 53
PAUSE Key 34
PerfectColor 59
Personal Computer 81
and Display Formats 38
Connecting 75
Setup 74
Picture Quality
and Connection Types 24
and Film Mode 57
Troubleshooting
97
Power Consumption 47, 92
Power On/Off 14, 97
Q
QV (QuickView
TM)
34
106
Index
R
Recording
and MONITOR OUT Jacks
19
and Split Screen 19
Cancelling Recordings
IEEE 1394 devices 83
Recording Setup Menu
and IEEE 1394 Devices 82
RECORD Button 99
Record List
and IEEE 1394 Devices 82
Signals Available for Recording
23
Remote Control
Batteries 35
Keys and Functions 34
Programming Codes (reference
chart) 64
Programming Instructions 63
Reset 35
Reset
A/V (all settings) 15
A/V Memory (for individual devices) 57
DVCR Counter 84
Pass Code 89
PerfectColor 59
Remote Control 35
System Reset Button 95
S
S-Video
Connecting 25
Connector Illustration
24
Safeguards 8
SAP (Second Audio Program) 58
Satellite Receiver
and the Remote Control 62
Connecting 25
IEEE 1394 84
SD (Standard-Definition
Signal) 38
Search A/V Disc. SeeA/V Discs
Service and Support 95
Setup Menu 45, 46
Signal Definitions 38
Sleep Timer 35
Software Updates 7
Speakers, Turning TV Speakers On or
Off 57
Specifications, TV 91
Split Screen
and Recording from MONITOR
OUT 19
Description
Stand, TV 6
40
Standard-Definition
Signal 38
Status Display 37
STATUS Indicator. See LED Indicator
Lights
Stereo System. SeeA!V Receiver
System Reset 95
T
3:2 pulldown 57
Time. See Clock
Timer (TV Timer) 47
Time Zone. See Clock
Troubleshooting 95
TV Reset Menu 95
V
VCR
Connecting 18, 28, 29
IEEE 1394 80
Troubleshooting
97
Video Noise Reduction 59
Video Settings 59
Viewing Device. See Input Selection
Menu
W
Wall Outlet Cable 26
MITSUBISHI
ELECTRIC
DIGITAL
TELEVISIONS"
Website:
www.mitsubishi-tv.com
E=mail:
[email protected]
For questions,
call Consumer
Relations
at
800=332=2119
To order replacement or additional
remote controls, lamp cartridges,
or Owner's
Visit our website
Guides
at www.mitsuparts.com
or call
800=553=7278
Demo Mode
This TV has a demo mode for use in retail stores.
Demo mode causes the TV to display a series of
screens outlining the TV's features.
To turn off demo mode:
1.
2.
3.
4.
Press MENU.
When the Main menu appears with Setup highlighted, press ENTER.
When the Setup menu opens, press I_ to highlight the on-screen Demo Mode Off button.
Press ENTER.
© 2006 Mitsubishi
853B542A10
Digital Electronics
America, Inc.
System Reset
If the TV does not respond to the remote control,
front panel controls, or will not power on/off, press
the SYSTEM
RESET
button on the front panel with a
pointed object, such as the point of a pencil or end
tip of a paperclip.
The green LED will flash quickly for about one
minute. When the green LED stops flashing, you
may turn on the TV. The changes you made most
recently, before using SYSTEM
RESET,
may be lost.
Changes you made previously, however, are not lost.
Written and Printed in U.S.A.
V33

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement