User Manual - TPC Advanced Technology

User Manual - TPC Advanced Technology
TPC
User Manual
LED 70N
Cordless LED Curing Light
• All instructions in this USER’S MANUAL must be completely read before installation or operation.
REV. 1-1-13
Table Of Contents
1. INTRODUCTION
1
1.1 TECHNICAL INFORMATION
1
2. FEATURES
2
3. ACCESSORIES
3
4. INSTALLATION
3-4
5. OPERATION
4-5
6. MAINTENANCE
6
8. WARRANTY 7
9. TROUBLESHOOTING
7
1.INTRODUCTION
Thank you for purchasing the LED 70N curing light . The LED 70N
is a dental curing light which uses the latest
LED technology to polymerize composite resin
Caution
Attention: Important information is being presented. Refer to the Operator’s Manual for more informa
tion.
High intensity Light: Protect your eyes from the light generated by this product
Shock Hazard: Beware of electrical shock or injury. Type B Applied Part
Class II Medical Equipment
Electronics Waste: Properly dispose of when use is discontinued.
1.1 Technical Information
Range of Light (in nm)
Light Intensity at the Tip (mW/cm2)
Battery Life
Charging Time to Complete
Battery Type
Cradle Battery
Operating Temperature
Power Input, Curing Light
Power Input, Power Supply
Pulse Rate
Pulse Duty Cycle
Storage and Transport Conditions
430 - 490 nm
2,200 mW
200 cycles at STANDARD mode, 10 seconds per cycle;
135 cycles at STANDARD mode, 20 seconds per cycle.
5 Hours
Lithium Ion 7.4V dc 2500mAh
Rechargeable
15 - 30°C (60 - 86°F); Unit turns off automatically when
the temperature at the wand tip reaches 48° C
9.0 VDC @ 1.6 A
100 - 240 VAC @ 50 - 60 Hz
10 Hz
50%
0 - 40°C (32 - 104°F)
0 - 100% RH
-1000 to + 9000 meters elevation
1
2.FEATURES
1. Latest LED technology.
2. Low heat output.
3. Easy operating with LCD Display.
4. Three preset programs
FAST : Full power output all time.
PULSE : 0.5 second interval after full power output for
Time (sec) 2.0
P : PULSE
Time (sec) 0.5
Light Intensity
(mW/cm2)
F : FAST
Light Intensity
(mW/cm2)
RAMP : Gradually increasing output in first half curing cycle , then Full power output till end.
Light Intensity
(mW/cm2)
S : STEP
Time (sec) 0.25
• Follow the manufacturer’s instruction to adjust the curing time for better curing performance.
5. Timer: Five preset curing time from 5, 10, 20, 30, and 40 seconds.
6. Low Battery Signal
When
is blinking on the LCD Display or there is a triple beep tone alarmed every 20 seconds , the battery needs to be charged for at least 4 hours.
7. Sleeping Mode
If the LED 70N is unused for a period of 3 minutes the curing light will convert to “Sleep Mode” to
conserve the battery.
8. Auto Memory
LED 70N will remain in previous settings. Including the curing time and the curing program.
9. Cord/Cordless Interchangeable
The LED 70N may be operated directly using AC power supply connected to the base of the handpiece.
This will allow users to operate the curing light while simultaneously charging the battery.
10. Build-in LCD Radiometer
User can monitor LED output by reading the radiometer which is located on the charging base.
2
3. Accessories
1. Curing Light Handpiece
2. Charging Base
3. Oval Protector
4. Light guide
5. Switching Power Adapter
6. Funchion Switch
7. Curing Switch
4. Installation
Step 1: Remove the battery cover located on the side of the handpiece. Connect the battery terminals and install the side cover.
Step 2: Connect the power adaptor to the charging base.
Step 3 : Directly insert the Light Guide into the curing light handpiece. Verify it has been completely inserted into handpiece. Light guide may be rotated to achieve best angle on tooth structure.
3
4. Installation
Step 4 : Install the eye Protector.
Step 5: Charge Lithium battery
For the best performance. Charge curing light handpiece continuously for 4 hours (charge battery at least 8
hours prior to initial use). The battery symbol on the LCD panel will show the sign of “full power” when battery
is completely charged. A flashing battery symbol indicates the battery should be recharged or user can directly
connect it to the power supply for uninterupted use.
LED 70N will detect the charging automatically. There will be one short beep tone generated when it has been
properly put on to the Charging Base.
5. Operation
A. Set Curing Program
Press and hold the function switch for two seconds and you will see the modes change every second. To stop on
the desired mode simply let go of the depressed button for the selected mode.
(1)
FAST
(2)
PULSE
(3)
RAMP
Indications on LCD Panel
1.Curing Time
2.Battery Sign
3.Curing Program
4
B. Set Timer
Press function switch to select curing time between 5, 10, 20, 30, and 40 seconds.
• When choosing PULSE or RAMP, the curing time will start at 10 seconds automatically.
C. Start to Operate
Press curing switch to begin curing program. To interrupt a program, just press curing switch again. When the
curing program is complete the curing light handpiece will beep and then turn off the light immediately.
D. Wake Up from Sleeping Mode
The curing light will turn into sleeping mode automatically when it is no longer in using for 3 minutes. Press
function switch or curing switch once to activate curing light.
E. Low Battery Sign
When the
is blinking, the curing light handpiece should be recharged immediately or directly connected to
the power sypply for continued use.
F. Turn off the Power
The curing light handpiece will achieve sleeping mode automatically. This will shut down all the curing function
to save the power. User may de-activate curing light by disconnecting the battery terminals from the battery.
G. Radiometer
Place the light guide against the detective spot on the radiometer. The meter will measure the intensity of LED
curing light and display the intensity on the LCD display.
• The output reading from the radiometer is a reference for the user to adjust to appropriate curing time. The radiometer is designed to test LED output only.
5
6. MAINTENANCE
1. Be sure there is no resin or material sticking to the surface of the light guide.
2. If materials are sticking on the light guide immediately clean it with soft cloth. Keep light guide clean for better light intensity and curing performance.
3. The light guide should be sterilized after each use. It can be safely autoclaved at 121 °C. For no more then 15 minutes. Let cool before handling.
4. The other accessories such as curing light hadpiece and eye protector should be scrubbed with pure water and sheathed in accordance with standard disinfection procedures.
5. Keep curing light handpiece in charging station while not in use.
6. Dispose Lithium battery according to the federal and state laws.
7. The User should wear colored protection glasses to avoid eyes injury due to LED light.
Warranty Information
All of our products sold are guaranteed to be free from defects in workmanship and materials for a 1 year from
date of purchase, unless otherwise stated. TPC will repair or replace any defective part at no charge. During the
warranty period. TPC will not be responsible for labor charges or shipping charges to / from the TPC facility.
This guarantee does not cover normal wear or stains on surface finish. The guarantee does not cover damage
resulting from improper installation or misuse. All claims against the freight carrier must be initiated at the time
the damaged items are received. The claim is the responsibility of the customer. We are improving our products
on a continuous basis. We reserve the right to make modifications without the need for prior notification and
are not obligated to modify previously manufactured items. Light guides and batteries are not covered under any
type of warranty.
6
7. Trouble Shooting
Fault Display is not functioning on the
curing light
When i press the function button
the mode does not change
When i use the light it over heats
Battery drains very quickly
The light does not functon after
charging but it will function when
the power supply is attached to the
bottom of the light.
There is no light emitting from the
light but the display functions.
When i place the curing light on
the charging base the battery does
not charge
Light intensity is reading low
Light guide does not fit properly in
the end of the curing light
Possible Cause Battery drained.
Button Is stuck
Fan not functioning
Battery is near end of life
Battery is exhausted
Solution
Charge Battery
Connect to power supply
Veryify the button depresses in and
pops back out.
Send to TPC for service
Charge battery
Verify charging cycle is complete
Replace battery
Temporarly use with power supply
Replace battery
Damaged LED
Send to TPC for service
Light not seated in base correctly
Dirty Contacts
Battery is exhausted
light guide is dirty or damaged
Battery is low
LED is burning out
O-ring is damaged
Reseat light in charging base
Clean Contacts
Repalce battery
Clean / repalce light guide
Charge battery
Return to TPC for service
Repalce O-ring
Warranty Card
Name:____________________________________________________
Address:__________________________________________________
City:_____________________State:______Zip___________________
Phone Number:(____)______-________FAX:(____)______-________
Email Address_____________________________________________
Model: LED 70N
Handpiece: SN________________
Base: SN_____________________
Please complete this card and return it to TPC. Include a copy of your invoice or packing slip.
Return to:
TPC Advanced Technology
851 S. Lawson St
City Of Industry, CA 91748
Or Email a scaned copy to [email protected]
7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement