User manual

Add to my manuals
24 Pages

advertisement

User manual | Manualzz

INSTRUCTIONS FOR USE &

MANUAL DAILY MAINTENANCE

VENTO CLASSIC SMALL

Gas fi re with closed combustion system

Bellfi res wishes you many cosy evenings with your new Bellfi res gas fi re

This document is an essential part of your gas fi re.

Read it carefully before use of the gas fi re and keep it in a safe place!

Serial number:

Production date:

Bellfi res

BELLFIRES GAS FIRE WITH CLOSED COMBUSTION SYSTEM:

Vento Classic Small (VCS)

English

Instructions for use

3

Bellfi res

English

4

Instructions for use

Bellfi res

English

CONTENTS

Page

1. WARRANTY TERMS ................................................................................. 7

2. INSTRUCTIONS FOR USE ....................................................................... 9

3. USING THE APPLIANCE FOR THE FIRST TIME ..................................... 20

4. DAILY MAINTENANCE .............................................................................. 20

5. ANNUAL MAINTENANCE .......................................................................... 21

Instructions for use

5

Bellfi res

English

6

Instructions for use

Bellfi res

1 WARRANTY TERMS

English

Interfocos

Warranty terms

Interfocos B.V. guarantees the quality of the supplied Bellfi res hearth and the quality of the materials used. All Bellfi res hearths are developed and manufactured according to the highest possible quality standards. If, despite all this, something should prove amiss with the Bellfi res hearth you have purchased, Interfocos B.V. offers the following manufacturer’s warranty.

Article 1: Warranty

1.1. If Interfocos B.V. determines that the Bellfi res hearth you have purchased is defective as a result of a fl aw in the construction or material, Interfocos B.V. guarantees to repair or replace the hearth free of charge, without charging any costs for labour or spare parts.

1.2. Repair or replacement of the Bellfi res hearth will be undertaken by Interfocos B.V. or by a Bellfi res dealer as designated by Interfocos B.V.

1.3. This warranty is supplementary to the existing legal national warranty of Bellfi res dealers and Interfocos B.V. in the country of purchase and is not intended to restrict your rights and claims based on the applicable legal provisions.

Article 2: Warranty conditions

2.1. Should you wish to claim under the warranty, please contact your Bellfi res dealer.

2.2. Complaints should be reported as quickly as possible after they have manifested themselves.

2.3. Complaints will only be accepted if they are reported to the Bellfi res dealer, together with the serial number of the Bellfi res hearth which is stated on the front of the instructions for use.

2.4. In addition, the original receipt (invoice, receipt, cash receipt) showing the date of purchase must also be submitted.

2.5. Repairs and replacements during the warranty period do not give any entitlement to an extension of the warranty period. After a repair or replacement of warranty parts, the warranty period shall be deemed to have started on the date of purchasing the Bellfi res hearth.

2.6. If a certain part is eligible for the warranty and the original part is no longer available, Interfocos B.V. shall ensure that an alternative part of at least the same quality shall be provided.

Article 3: Warranty exclusions

3.1. The warranty on the Bellfi res hearth ceases to be in effect if: a. it is not installed according to the supplied installation instructions, and to national and/or local regulations; b. it has been installed, connected or repaired by a non-Bellfi res dealer;

Instructions for use

7

Bellfi res

English c. it has not be used or maintained according to the instructions for use; d. it has been changed, neglected or roughly treated; e. it has been damaged as a result of external causes (outside the hearth itself), for example, lightning strike, water damage or fi re;

3.2. In addition, the warranty lapses if the original purchase receipt shows any change, deletion, removal or if it is illegible.

Article 4: Warranty area

4.1. The warranty is only valid in those countries where Bellfi res hearths are sold through an offi cial dealer network.

Article 5: Warranty period

5.1. This warranty will only be granted during the warranty period.

5.2. The body of the Bellfi res hearth is guaranteed for a period of 10 years against construction and/or material faults, starting from the moment of purchase.

5.3. For other parts of the Bellfi res hearth, a similar warranty applies from the moment of purchase for a period of one year.

5.4. For user parts such as glass, glass (cord), thermocouple and the interior of the combustion chamber, a similar guarantee is given until after the fi rst burning.

Article 6: Liability

6.1. A claim granted by Interfocos B.V. under this warranty does not automatically imply that Interfocos B.V. also accepts liability for any possible damage.

The liability of Interfocos B.V. never extends further than that stated in these warranty conditions. Any liability of Interfocos B.V. for consequential damage is expressly excluded.

6.2. That stated in this provision is not valid if and to the extent that is derives from a mandatory provision.

6.3. All agreements entered into by Interfocos B.V. are, unless specifi cally stated otherwise in writing and to the extent that they are permitted based on applicable law, subject to the Conditions of the Dutch Metal and Engineering Association

(METAALUNIEVOORWAARDEN), as fi led with the registrar of the Court of

Rotterdam on 1 January 2008.

Interfocos B.V.

Hallenstraat 17

5531 AB Bladel

The Netherlands

Tel: +31-497339200

Email: info@Bellfi res.com

Carefully retain the instructions for use; they show the serial number of the hearth.

You will need this if you wish to claim under the warranty.

8

Instructions for use

Bellfi res

English

2 INSTRUCTIONS FOR USE

2.1 INTRODUCTION

Congratulations on your purchase of this modern Bellfi res gas fi re. This quality product will provide you with many years of enjoyment due to the fl ame effect and warmth that it provides. Please read the instructions for use carefully before using the appliance for the fi rst time. Keep this booklet in a safe place.

2.2 BUILT-IN PROTECTION OF THE APPLIANCE

The appliance is fully protected by means of a thermo-electric pilot light shut off in the event of a gas escape from the main burner.

2.2.1 Safety

Do not place embers, vermiculite granules, wood logs or pebbles against the pilot light burner. Make sure that the pilot fl ame can burn at all times freely over the main burner. Only in this way is proper ignition of the main burner ensured.

Ignoring these directions could lead to a dangerous situation.

Do not place fl ammable objects within 100 cm of the appliance. Pay special attention to furnishings and ornaments around the fi re.

When igniting the pilot light and burner, always keep a minimum distance of 100 cm from the front of the appliance.

If the pilot fl ame goes out for any reason, wait for 5 minutes before attempting to re-light it.

It is essential that the appliance, the complete concentric fl ue system and the outlet are cleaned and inspected annually by a recognised fi tter/gas specialist. The safe operation of the appliance will thus remain guaranteed.

For this, please refer to the Installation instructions (Chapter 2:

Maintenance), that are supplied separately with each appliance.

The gas fi re must never be used with the door open or the door glass removed.

Instructions for use

9

Bellfi res

Never place fl ammable material on the ceramic log set.

English

The fi lling of the main burner with embers, vermiculite granules, wood logs or pebbles may not under any circumstances be changed or added to.

Do not place easily-fl ammable materials, such as nylon clothing or fl ammable liquids, in the vicinity of the gas fi re.

Ensure at all times that children and other people who are not aware of the operation of the gas appliance are only in the vicinity of the appliance exclusively under supervision.

Use a fi reguard to protect the people and children mentioned above against possible burns.

2.3 OPERATION: REMOTE CONTROL

10

Instructions for use

Bellfi res

English

2.3.1 General

Read these instructions carefully before lighting the fi re !!

The appliance is opperated by radio remote control. This comprises a hand-held transmitter and a receiver. The receiver is part of the gas control block assembly.

The receiver and the gas control block are behind the (white) panel door (operating unit) next to the appliance. Press the door inwards to open; this will release the catch and the door will spring out.

The hand-held transmitter and receiver are powered by batteries.

Hand-held transmitter : 1x 9V battery.

Receiver : 4x 1.5V battery type LR6 or AA.

Option: 6V adapter (230 VAC). Available from your fi tter.

Note: Hand-held transmitter and receiver are not interchangeable with previous models.

The pilot light is situated in the front of the burner, behind a cowl. Should the pilot light

go out, you must wait fi ve (5) minutes before attempting to re-ignite the fi re.

Important

Once the fi re is lit, it must burn at maximum for approx. 10 minutes to allow the chimney to come up to temperature!

2.3.2 Hand-held transmitter

The remote control works by radio signal. The hand-held transmitter is confi gured in the factory with a unique signal code.

Figure 1: Hand-held transmitter

Instructions for use

11

Bellfi res

English

Set the display

• Connect the batteries. By simultaneously pressing OFF and (small fl ame), can be

switched from °F (and 12 hour clock) to °C (and 24 hour clock), or vice versa.

• The display will automatically return to mode after some time, but you may

immediately return to mode by pressing the OFF button.

Set the current time

• By simultaneously pressing (large fl ame) and (small fl ame), the display fl ashes.

You are in SET mode.

• While the screen is fl ashing, you can adjust the time.

• Press (large fl ame) to set the hour and (small fl ame) to set the minute.

• Wait or press OFF to return to mode.

Important: Setting up signal code before using the appliance for the fi rst time.

Before the appliance can be used, the receiver must fi rst learn the hand-held transmitter’s signal code.

• Press the “RESET” button on the receiver, and keep this pressed until 2 audio signals

are heard. See fi gure 2.

Release the “RESET” button after the second (somewhat longer) audio signal.

• Press, within 20 seconds, the (small fl ame) button on the hand-held transmitter,

until 2 short signals are heard. The signal code has now been set up on the receiver .

If, however, a single long sound is heard, this means that setting the signal code has

failed or that the wiring has been connected incorrectly.

You only need to set up the signal code once. It is not necessary when changing the batteries of the hand-held transmitter or receiver.

Figure 2: Receiver “RESET” button

12

Instructions for use

Bellfi res

English

Operating possibilities

It is possible to use the remote control in 3 ways to operate the appliance:

1 :

2 : and

3 :

You can cycle through the menu with operating possibilities by repeatedly depressing the SET button.

At the selected starting time (P1 or P2 ) or stopping time (P1 or P2 ) is also shown.

Returning to is also possible by pressing the (small fl ame) or (large fl ame) button.

Manual operation

Here you can turn the burner on and off, and adjust the height of the fl ames.

• Press (large fl ame) to turn on the burner and to increase the fl ame

height.

• Press (small fl ame) decrease the fl ame height to turn the burner off.

The pilot light will keep burning. (Stand-by position)

• The appliance will automatically revert to stand-by if:

° the hand-held transmitter is outside the range of the receiver for more

than 6 hours.

° the batteries in the hand-held transmitter are almost depleted.

° the batteries in the receiver are fully depleted. (The pilot light will also

be turned off.)

This also applies to the Thermostat and Timer operation.

• When one of the buttons on the hand-held transmitter is pressed (except

the SET button), the transmission symbol appears on the screen.

The receiver confi rms the transmission with an audio signal.

Operating day temperature thermostat

(Appliance is in the stand-by position and the pilot light is burning.)

Automatic temperature regulation of the pre-set day temperature.

The room temperature is measured and compared with the pre-set day temperature. The fl ame height is automatically regulated so as to reach the pre-set day temperature.

Also see: Setting the desired temperature.

Instructions for use

13

Bellfi res

English

Operating the night temperature thermostat

(Appliance is in the stand-by position and the pilot light is burning.)

Automatic temperature regulation of the pre-set night temperature.

The room temperature is measured and compared with the pre-set night temperature. The fl ame height is automatically regulated so as to reach the pre-set night temperature.

Also see: Setting the desired temperature.

Timer operation

(Appliance is in the stand-by position and the pilot light is burning.)

Appliance functions automatically according to the two pre-set heating periods;

P1 and P2. These heating periods repeat automatically every 24 hours.

Also see: Programming the timer: P1 and P2.

The appliance works thermostatically at the pre-set starting times P1 and

P2 and the room temperature is automatically regulated to the pre-set day temperature .

The appliance works thermostatically at the pre-set stopping times P1 and

P2 and the room temperature is automatically regulated to the pre-set night temperature .

In order to allow the appliance to regulate the temperature at night, the night temperature must be set to at least 5°C.

If the setting is lowered to , the appliance will switch to stand-by at night. The appliance will automatically operate at the following day cycle

.

N.B.: The pre-set temperature is shown on the screen every 30 seconds.

Setting the desired temperature

• Select the desired mode of operation or by pressing the SET button

briefl y.

• Press the SET button until the temperature indication on the display begins to fl ash.

• Set the temperature with (large fl ame) or (small fl ame).

• Wait or press the OFF button briefl y to go to mode.

• If the temperature control in should be off (lower battery consumption),

decrease the night temperature until appears on the display.

Important: Place the hand-held transmitter in a place that is not infl uenced by direct sunlight, draught, heat from the appliance and other heat sources.

14

Instructions for use

Bellfi res

English

Programming the timer: P1 and P2

• Select the desired mode of operation by pressing the SET button briefl y.

• Press the SET button until P1 (heating period 1) and the time appear in the

display. (The time indication fl ashes.)

• Set the time for the beginning of the fi rst heating period by pressing (large fl ame)

for houre and (small fl ame) for minute’setting.

• Press the SET button briefl y; P1 appears on the display. Set the time for the end

of the fi rst heating period.

• Press SET again to set the second heating period P2 (heat ON) and P2 (heat

OFF).

• Wait a moment or press OFF to switch back to mode.

2.3.3 Operation (Remote Control)

Igniting the fi re

• Open the gas supply valve in the gas pipe to the fi re.

• Press the “O I” switch on the gas control block to the “I” position.

• Turn the operating knob on the gas control block to the ON position.

• Switch the hand-held transmitter to the position.

• On the hand-held transmitter, press the OFF and (large fl ame) buttons

simultaneously. A short tone will signal the start. Release the buttons. Short beeps

will then follow until the pilot light and main burner are ignited. Once the main burner

has been ignited, the fl ame height will automatically rise to the maximum position.

Important: • If the pilot fl ame goes out for any reason, wait for 5 minutes

• before attempting to re-light it.

If the pilot light does not ignite after 3 ignition attempts; close the gas tap and warn the fi tter.

Once the pilot light is burning, the main burner must ignite within 10 seconds automatically.

If this does not happen, immediately close the gas tap and warn the fi tter.

If the main burner ignites with a pop; immediately close the gas tap and warn the fi tter.

Instructions for use

15

Bellfi res

English

ON/OFF Switch

8-wire

Receiver Jack

Microswitch

Connection Piezo Igniter

(only for MANual control)

Operating Knob

Motor-Knob

(in maximum position)

Figure 3: Gas regulating block; Operating Knob in ON-position

• Possible error messages:

* 3x short audio signal, audible when the motor-knob operates:

Receiver batteries need changing soon (having heard this signal, the

appliance can be ignited another ten times approximately).

* 5 second unbroken tone:

Error. For example, one of the cables may not be properly connected,

the “O I” switch is not in the “I” position.

* 5 short beeps:

Ignition of the pilot light and main burner failed. Possible cause: air in

the pilot light pipe.

Important: If the pilot fl ame goes out, then wait for at least 5 minutes before repeating the above procedure.

Setting the fl ame height / extinguishing the fi re

• After ignition, the burner automatically sets the fl ames to the maximum height.

• Press button (small fl ame) to lower the fl ames and to turn off the main burner

(Extinguishing the fi re: small fl ame button: pilot light remains burning (stand-by position)!)

(Pressing briefl y the (small fl ame) button gradually lowers the fl ames to the low position.)

Pressing the (small fl ame) button twice automatically lowers the fl ames to the low position. (When this happens, the fl ames will fi rst automatically go to maximum!)

This is indicated by “LO” on the display.

16

Instructions for use

Bellfi res

English

• Press button (large fl ame) to increase the fl ame level and to turn on the burner from the stand-by position.

(Pressing briefl y the (large fl ame) button gradually increases the fl ames to the

high position.)

Pressing the (large fl ame) button twice automatically increases the fl ames to the high position. This is indicated by “HI” on the display.

Important: • If you turn on the main burner by pressing the (large fl ame) button, it must ignite within 10 seconds.

If this does not happen, immediately close the gas tap and warn the fi tter.

• If the main burner ignites with a pop; immediately close the gas tap and warn the fi tter.

Switching off the appliance

• Press the (small fl ame) button to lower the fl ames or to switch off the main burner.

• Then press the OFF button to switch off the appliance, including the pilot light.

• Press the “O I” switch (on the gas control block) to the “O” position. This conserves battery life.

• If the appliance is not to be used for some time, please close the gas supply valve in the gas pipe.

Important: If the pilot fl ame goes out for any reason, wait for 5 minutes before attempting to re-light it.

Faults

• If the signals from the hand-held transmitter do not seem to be reaching the receiver, the cause may be:

* Spent batteries: replace the batteries.

* An electronic problem: press the “RESET” button on the receiver.

• If the appliance regularly switches itself off, please contact your installer.

Replacing the batteries

• The hand-held transmitter/receiver batteries have a service life of approx. one year.

We recommend you use alkaline batteries.

Rechargeable batteries are not permitted.

• The batteries must be replaced whenever:

1 Hand-held transmitter : The battery symbol indicates this in the display.

: Battery fully charged

: Battery empty

2 Receiver: 3x short audio signal, audible when the motor-knob operates.

Instructions for use

17

Bellfi res

English

1 Hand-held transmitter:

* Open the cover on the back of the transmitter.

* Carefully remove the 9V battery and disconnect it from the contact.

Do not pull the wires!

* Connect the new battery and replace in the battery compartment. Close the cover.

2 Receiver:

* Carefully pull the receiver assembly out of the compartment behind the (white)

panel door.

* Open the cover.

* Remove the batteries from the battery compartment.

* Place four new 1.5V batteries (LR6 or AA type) as indicated in the battery

compartment. The negative end (-) of the battery must always be at the contact

spring end of the compartment.

* Close the cover and place the receiver back in its holder.

• If the batteries are inserted incorrectly, the electronics or drive may be irreparably damaged.

• Only replace the batteries when the appliance has been completely switched off.

2.3.4 Operation (Hand control)

In an emergency it is possible to operate the appliance manually. To do so, the ignition

(piezo) cable must fi rst be removed and transferred carefully to the piezo connector on the gas control block.

Piezo button

(only for MANual control)

ON/OFF Switch

8 Wire

Receiver Jack

Connection Piezo Igniter

(only for MANual control)

Metallic Core for Manual

Ignition (recessed switch)

Operating Knob

(in Position for

Manual Ignition)

Microswitch

Motor-Knob

(in maximum position)

Figure 4: Gas regulating block; Operating Knob in MAN-position

18

Instructions for use

Bellfi res

English

Igniting the fi re

• Open the gas supply valve in the gas pipe to the fi re.

• Switch the “O I” switch on the gas regulating block to the “I” position.

• Turn the motor-knob on the gas regulating block completely to the right, in the OFF position. The switch will audibly ‘click’.

• Turn the operating knob on the gas control block to the MAN position. A recessed switch within the knob will become visible.

• Press the recessed switch. Use a pen or similar instrument to do this.

Gas will now fl ow to the pilot light.

• While holding down the recessed switch, press the (square) piezo button several times (the piezo button is alongside the “O I” switch) to ignite the pilot light.

Check whether the pilot light has been lit through the glass.

l

Once the pilot light is lit, the recessed switch must be kept down for a further ten seconds, after which it can be released.

Important: If the pilot fl ame goes out, then wait for at least 5 minutes before repeating the above procedure.

• Move the operating knob to the ON position. Depending on the position of the motorknob, the burner will either ignite or not.

• By turning the motor-knob anti-clockwise to the desired position, the burner will ignite and the fl ame height can be controlled.

Important: • When the main burner is switched on by turning

the motor knob to the left, the burner must

ignite within 10 seconds.

If this does not happen, immediately close the

gas tap and warn the fi tter.

• If the main burner ignites with a pop; immediately

close the gas tap and warn the fi tter.

Extinguishing the fi re

• Turn the motor-knob on the gas regulating block as far as it will go in a clockwise direction. The knob will audibly ‘click’. The burner is now switched off. The pilot light will remain lit.

Switching off the appliance

• Press the “O I” switch on the gas regulating block to the “O” position.

The pilot light will be extinguished.

• If the gas fi re is not going to be used for a long period of time, it is

recommended to close the gas supply valve to the fi re.

Important: If the pilot fl ame goes out for any reason, wait for 5 minutes before attempting to re-light it.

Instructions for use

19

Bellfi res

English

3 USING THE APPLIANCE FOR THE FIRST TIME

The gas fi re is coated with a lacquer layer resistant to high temperature. During the fi rst hours of operation, the burning in of the lacquer may result in an unpleasant smell. This is harmless, however. Operating the gas fi re at full capacity for a few hours, while ventilating the room, will eliminate the smell.

After using your gas fi re for the fi rst few times, you may be aware of a light deposit on the inside off the glass. This is caused by the paint curing. Once your fi replace has cooled down, this deposit can be removed with glass cleaner or ceramic hob cleaner.

4 DAILY MAINTENANCE

• Ensure that as little dust, and as few particles of cigarette smoke, candles and oil

lamps as possible pollute the air in the room in which the appliance is used. Heating

of these particles by the convection system of the appliance could lead to

discoloration of the walls and ceiling. It is therefore very important to ensure that the

room in which the appliance is located is suffi ciently ventilated. Regularly remove

any dust deposits from behind the (white) panel door (operating unit) by means of a

vacuum cleaner.

Important: • Regularly clean the glass on the inside of the appliance with

glass spray or ceramic hob cleaner.

Attention!! If the glass is not cleaned on time, this can result in becoming dull and diffi cult, if not impossible, to clean.

(See installation instructions for dismantling/assembling the glass.)

• If the glass is broken or cracked, it must be

immediately replaced before operating the

gas fi re again.

Ceramic heat-resistant glass may not be placed in the glass container, but must be included in normal household waste.

• If anything is spilt on the fi re, switch it off immediately and wait for it to cool

down suffi ciently before cleaning. Never use scouring powder, aggressive

cleaners or fi re polish on the gas fi re. Use only a dry lint free cloth.

• Heat resistant lacquer in aerosols can be obtained from your distributor. During the yearly maintenance, the lacquer can be used to repair small areas of damage.

20

Instructions for use

Bellfi res

English

5 ANNUAL MAINTENANCE

It is essential that the appliance, the complete concentric fl ue system (where possible) and the outlet are cleaned and inspected annually by a recognised fi tter/gas specialist.

The safe operation of the appliance will thus remain guaranteed.

Please refer also to the Installation instructions that are supplied separately with each appliance.

Instructions for use

21

Bellfi res

English

22

Instructions for use

Your Bellfi res dealer

02 - 011112 - 331775

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement