16-Port 10/100Base Fast Ethernet PoE Ethernet Switch FCC Warning Package Contents Front Panel (LEDs) This device has been tested and found to comply with limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates and radiates radio frequency energy and, if not installed and used in accordance with the user’s manual, it may cause interference in which case users will be required to correct interference at their own expenses. Before you start to install this switch, please verify your package that contains the following items: LED Indicators of 16 Port PoE 10/100M Switch z One PoE Fast Ethernet Switch z One Power Cord z One User’s Manual LED Power Status On Off LINK/ACT On Off Flashing PoE On Off CE Warning User’s Manual This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. Connections Switch/Hub to this 16 Port PoE Fast Ethernet Switch Introduction This switch provides 16 10/100M ports. It was designed for easy installation and high performance in an environment where traffic is on the network and the number of users increases continuously. It consists of 16 PSE/PoE ports. That can solve the limitation of the power outlet location and offer the system designer a flexible solution to locate the network device everywhere. The rack-mount size was specifically designed for medium to large workgroups. The Switch can be installed where space is limited; moreover it provides smooth network migration and easy upgrade to network capacity. The 19” size can be rack-mount on 19” cabinet. Description Power is on. Power is off. Port is for connection. No connection. Data is transmitting or receiving Port is linked to Power Device No Power Device is connected Note: If any of these items is found missing or damaged, please contact your local supplier for replacement. Key Features z 16 Port 10/100M Nway (Auto-negotiation) Switch z 16 PSE/PoE function ports z Supporting the power Max. 15.4 W for each PSE/PoE port z 19” rack-mount size z Auto-learn of networking configurations z Auto-detect full/half-duplex modes for any port z Dedicated full-duplex 200Mbps bandwidth z Store-and-Forward switching methods z IEEE 802.3x flow control for full-duplex and back-pressure flow control for half-duplex z Non-blocking & Non-head-of-line blocking full wire speed forwarding z Auto-MDI/MDI-X function for any port z Smart plug & play This switch provides automatic crossover detection functionality for any port. It is simple and friendly to up-link to another switch without crossover cable. PC/Other devices to this 16 Ports Fast Ethernet Switch Via a twisted pair cable straight through, this switch can be connected to PCs, servers and other network devices. Technical Specifications Standards Features Filtering/ Forwarding Rates Transmission Media Power Device to this 16 Port PoE Fast Ethernet Switch and getting 48V power source through Cat. 5 cables Using Cat. 5 twisted-pair cable to connect Power Device to the port 1~16 of this switch, and then this switch will supply 48V power to Power Device over Cat. 5 twisted-pair cable. Please be noted Power Device should also comply with IEEE 802.3af. Rear Panel (Power) AC input AC input (90~260V/AC, 50~60Hz) UL Safety LED Indicators Power Input IEEE 802.3af IEEE 802.3 10Base-T IEEE 802.3u 100Base-TX IEEE 802.3x Flow control Number of Ports: 16 PSE/PoE Ports MAC Address: 4K Buffer Memory: 1.625 Mb Method: Store and Forward 100Mbps port – 148,800pps 10Mbps – 14,880pps 10Base-T Cat. 3, 4, 5 UTP/STP 100Base-TX Cat. 5 UTP/STP Per Port: LINK/ACT, PoE ACT/Status Per Unit: Power 100~240V/AC, 50~60Hz 48V/DC Per Port Output – Power Output Power Consumption Dimensions Weight Operating Temperature Storage Temperature Humidity Certifications Rack-mount Kits 15.4 W Max Per Port 16 Ports at Full 15.4 W Output Supported 260 Watts (Max) 440 × 220 × 44 mm (L x W x H) 3.8 kg 0 to 55℃ -20 to 90℃ 10 to 90% RH (non-condensing) FCC Class A, CE z Install the rack-mount kits with eight screws. z Use four screws to install the unit in a 19” cabinet. We suggest using two screws per ear to install in a 19” cabinet. z The heads of the screws should be less than 5 mm in diameter, and the shafts should be less than 2.93 mm in diameter, as show in the figure above.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project