Untitled

Untitled
Page 2 of 109
Report No.:
11015280 001
Copy of marking plate:
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 3 of 109
Report No.:
11015280 001
Copy of marking plate:
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 4 of 109
Report No.:
11015280 001
Copy of marking plate:
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 5 of 109
Report No.:
11015280 001
Copy of marking plate:
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 6 of 109
Report No.:
11015280 001
Copy of marking plate:
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 7 of 109
Report No.:
11015280 001
Copy of marking plate:
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 8 of 109
Report No.:
11015280 001
Copy of marking plate:
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 9 of 109
Report No.:
11015280 001
Copy of marking plate:
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 10 of 109
Report No.:
11015280 001
Copy of marking plate:
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 11 of 109
Report No.:
11015280 001
Copy of marking plate:
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 12 of 109
Report No.:
11015280 001
Summary of testing:
•
The max. ambient temperature is depend on the different adapter source used, detailed information similar
to below table are given in the user’s manual to guide the user to use suitable adapter.
Model
MS-163Axx
Max. ambient
temperature
Applicable adapter
40°C
Delta / ADP-120ZB BB
(manufacturer/ type designation)
Lite-On / PA-1121-04
MS-163Gxxx, MS163Pxxxx,
M655xxxxx, MS1039xxxxx, MS1636xx, LGE50,
E500, ED500, MS163Nxxx
1) 40°C
MS-1637xx, MS1613-xxxxx, MS1034xxxxx, MS163Cxx,
M662xxxxx,
M660xxxxx, F1,
LGF1
1) 40°C
2) 25°C
1) Li shin / LSE0202D1990; LSE0202C1990
Lite-on / PA-1900-04; PA-1121-04
EPS / D10903-A
EDAC / EA10953
Delta / ADP-120ZB BB, ADP-90SB BB
2) FSP / FSP090-1ADC21XX
2) 25°C
3) 35°C
1) Li shin / LSE0202D1990; LSE0202C1990
Lite-on / PA-1900-04; PA-1121-04
EPS / D10903-A
EDAC / EA10953
Delta / ADP-120ZB BB, ADP-90SB BB
2) FSP / FSP090-1ADC21XX
3) Lite-on / PA-1650-02XX
•
Perform test under highest load for this equipment as reading/writing between HDD and playing optical
drives, Max. brightness and contrast for LCD panel, the dummy loads of 2.5W for each USB, IEEE1394
ports and RJ45 transmission signal to other PC or server, charging to an empty battery pack. The operator
can connect additional options like a parallel printer or a serial device.
•
CPU: Intel, 2.16GHz for models MS-1034xxxxx, M660xxxxx, M662xxxxx, LGF1, F1 and Intel, 2.2GHz
for models MS-1039xxxxx and M655xxxxx.
CPU: Intel PBGA (478pin), 2.2GHz for models MS-1637xx, MS-163Nxxx, MS-1636xx, MS-163Cxx,
M163Axx, LGE50, E500 and ED500.
CPU: Intel / Celeron 530, 1.73GHz for model MS-163Pxxxx
Unless otherwise indicated, all tests are conducted to model MS-1039xxxxx, MS-1636xx and MS1637xx, M163Axx, MS-163Gxxx, MS-1034xxxxx, MS-163Nxxx, MS-163Pxxxx to represent all other
models.
The TV tuner design for model MS-163Axx was evaluated according to clause 7 of IEC 60950-1:2005,
CB countries should investigate this matter during national mark approval.
•
•
•
•
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 13 of 109
Report No.:
11015280 001
.
Model
DC Fan used under Test
Mainboard/TNV
board
Bottom enclosure
MS-1039xxxxx
Mfr. Forcecon, type
451005M10T (5.1CFM)
Mainboard
A/TNV board (a)
Bottom Enclosure (A)
M655xxxxx
Mainboard B/
TNV board (a)
MS-1034xxxxx
LGF1, F1, MS-1613xxxxx, M662xxxxx,
M660xxxxx
MS-163Nxxx
Mfr. Forcecon, type
DFS450805M10T (3CFM)
Mainboard G/
TNV board (b)
MS-163Pxxxx
Mfr. Forcecon, type
DFS451205M10T (4.5CFM)
Mainboard H/
TNV board (c)
LGE50, E500, ED500
Mfr. Forcecon, type
DFS450805M10T (3CFM)
Mainboard C, F/
TNV board (a)
MS-163Gxxx
Mfr. Forcecon, type
DFS451205M10T (4.5CFM)
Mainboard F/
TNV board (a)
MS-163Axx
Mfr. Forcecon, type
DFS450805M10T (3CFM)
Mainboard E/
TNV board (a)
MS-1637xx, MS163Cxx
Mfr. Forcecon, type
DFS450805M10T (3CFM)
Mainboard C
TNV board (b)
MS-1636xx
Mfr. Forcecon, type
DFS450805M10T (3CFM)
Mainboard D/
TNV board (b)
Bottom Enclosure (B)
Particulars: test item vs. test requirements
Equipment mobility .......................................: Transportable equipment
Operating condition .......................................: Continuous
Mains supply tolerance (%) ...........................: No direct mains connection
Tested for IT power systems ........................: No
IT testing, phase-phase voltage (V) .............: N/A
Class of equipment .......................................: III
Mass of equipment (kg).................................: 2.8
Protection against ingress of water ..............: IPX0
Test case verdicts
Test case does not apply to the test object ..: N/A
Test item does meet the requirement ..........: P(ass)
Test item does not meet the requirement ....: F(ail)
Testing
Date of receipt of test item ...........................: Nov., 2008
Date(s) of performance of test .....................: Nov.-Dec., 2008
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 14 of 109
Report No.:
11015280 001
General remarks
”This report is not valid as a CB Test Report unless appended by an approved CB Testing
Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02”.
The test result presented in this report relate only to the object(s) tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
”(see Enclosure #)" refers to additional information appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a point is used as the decimal separator.
Comments:
For all models except for MS-163Axx:
Summary of compliance with National Differences (for explanation of codes see below):
EU Group Differences, EU Special National Conditions, EU A-Deviations, AR, AT, AU, BE, CA, CH, CN,
DE, DK, FI, FR, GB, GR, HU, IL, IN, IT, KE, KR, MY, NL, PL, SG, SI, SK, US
AR=Argentina, AT=Austria, AU=Australia, BE=Belgium, CA=Canada, CH=Switzerland, CN=China,
CZ=Czech Republic, DE=Germany, DK=Denmark, FI=Finland, FR=France, GB=United Kingdom,
GR=Greece, HU=Hungary, IL=Israel, IN=India, IT=Italy, KE=Kenya, KR=Korea, MY=Malaysia, NL=The
Netherlands, NO=Norway, PL=Poland, SE=Sweden, SG=Singapore, SI=Slovenia, SK=Slovakia, US=United
States of America.
For National Differences see end of this test report.
For model MS-163Axx only:
Summary of compliance with National Differences (for explanation of codes see below):
EU Group Differences, EU Special National Conditions, EU A-Deviations, AR, AT, AU, BE, CA, CH, CN,
DE, DK, FR, GB, GR, HU, IL, IN, IT, KE, KR, MY, NL, PL, SE, SG, SI, SK, US
AR=Argentina, AT=Austria, AU=Australia, BE=Belgium, CA=Canada, CH=Switzerland, CN=China,
CZ=Czech Republic, DE=Germany, DK=Denmark, FI=Finland, FR=France, GB=United Kingdom,
GR=Greece, HU=Hungary, IL=Israel, IN=India, IT=Italy, KE=Kenya, KR=Korea, MY=Malaysia, NL=The
Netherlands, NO=Norway, PL=Poland, SE=Sweden, SG=Singapore, SI=Slovenia, SK=Slovakia, US=United
States of America.
For National Differences see end of this test report.
Factories:
1. MSI Computer (Shenzhen) Co., Ltd.
Longma Information Technology Industrial Park, Tangtou Village, Shiyan Town, Baoan District,
Shenzhen, Guangdong 518108, P.R. China
2. MSI ELECTRONICS (KUNSHAN) CO., LTD.
88E QIANJIN Rd., Kunshan City, Jiangsu 215300, P.R. China
3. LG Electronics de Sao Paulo Ltda.
Avenida Dom Pedro 1, W-7777 Distrito Ind. Piracangagua II Taubate, SP Brazil
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 15 of 109
Report No.:
11015280 001
Definition of variables:
Variable:
Range of variable:
Content:
x
(for models
MS1034xxxxx,
MS-1637xx,
MS-163Cxx,
MS-1636xx,
MS1613xxxxx,
MS-163Axx,
MS163Nxxx,M6
60xxxxx,
M662xxxxx,
MS1039xxxxx,
M655xxxxx)
0-9, A-Z or blank
Marketing purpose, no technical differences
x
(for model
MS163Gxxx,
MS163Pxxxx)
0-9, a-z, A-Z or blank
Marketing purpose, no technical differences
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 16 of 109
Report No.:
11015280 001
General product information:
The equipment is Notebook PC intended for general office use.
The external power adapters (SPS) which used in final system are CB scheme tested according to IEC
60950-1: 2001, see appended table 1.5.1 for detail information.
This equipment model MS-163Axx provide an TV card which intended to be connected to the cable
distribution system and which has been evaluated according to clause 7 of IEC 60950-1:2005, CB countries
should investigate this matter during national mark approval.
This report contains all national deviation as the class III equipment itself is subject of this CB report, but CB
countries using for external power adapter should investigate while the equipment under test is submitted
for national approval.
Model Differences:
Model MS-1034xxxxx is similar to model MS-1039xxxxx except for design of motherboard, maximum
ambient temperature, input current rating, sources of power adaptor and model designation.
Models M662xxxxx and M660xxxxx are similar to model MS-1034xxxxx except for type of keyboard,
camera and model designation.
Model M655xxxxx is identical to model MS-1039xxxxx except for model designation.
Models LGF1 and F1 (LG) are identical to model MS-1034xxxxx, except for model designation and
trademark.
Models MS-1613-xxxxx (x=0-9, A-Z or blank) which is similar to model MS-1034xxxxx (x=0-9, A-Z or blank)
except for the model designation.
Models MS-1637xx (x = 0-9, A-Z or blank), which is similar to previous model MS-1034xxxxx except model
name, main board and TNV board, DC fan source, bottom openings.
Models MS-1636xx (x = 0-9, A-Z or blank), which is similar to previous model MS-1637xx except model name,
main board, DC fan source, current rating as 4.74A
Models MS-163Nxxx (x = 0-9, A-Z or blank), which is similar to previous model MS-1636xx except model
name, main board, input rating
Models MS-163Pxxxx (x = 0-9, a-z, A-Z or blank), which is similar to previous model MS-163Gxx except for
model name, main board, CPU source, additional dummy card provided, TNV-board and PTC sources.
Models LGE50, E500, ED500 (LG), that are similar to previous models MS-1637xx except for trademark,
model name, white color enclosure and 4.74A current rating only.
Models MS-163Cxx (x=0-9, A-Z or blank) which is similar to previous model MS-1637xx (x=0-9, A-Z or
blank) except for model designation.
Model MS-163Axx is similar to previous model MS-1637xx except for mainboard, electric rating and model
designation.
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 17 of 109
Report No.:
11015280 001
Model MS-163Gxxx is similar to previous model MS-1636xx except for mainboard and model designation.
Model
Mainboard
TNV board
Bottom enclosure
MS-1039xxxxx
Mainboard A
TNV board (a)
Bottom Enclosure (A)
M655xxxxx
MS-1034xxxxx
Mainboard B
LGF1, F1, MS-1613xxxxx, M662xxxxx,
M660xxxxx
LGE50, E500, ED500
Mainboard C, F
Bottom Enclosure (B)
MS-163Gxxx
Mainboard F
MS-163Axx
Mainboard E
MS-163Pxxxx
Mainboard H
TNV board (c)
MS-1637, MS-163Cxx
Mainboard C
TNV board (b)
MS-1636
Mainboard D
MS-163Nxxx
Mainboard G
Model
DC Fan source
MS-1637xx, MS163Cxx
Mfr. LG, type MFNC-C537F (4.5CFM)
Mfr. LG, type MFNC-C537A (5.0CFM)
Mfr. LG, type MFNC-C537D (3.6CFM)
Mfr. Forcecon, type DFB450805M10T(5.01CFM)
Mfr. Forcecon, type DFS450805M10T (3CFM)
Mfr. Forcecon, type 451005M10T (5.1CFM)
Mfr. Tranyoung, type 6010H05F PF3 (7.08CFM)
MS-1636xx, MS163Nxxx
Mfr. LG, type MFNC-C537F (4.5CFM)
Mfr. LG, type MFNC-C537A (5.0CFM)
Mfr. Forcecon, type DFB450805M10T(5.01CFM)
Mfr. Forcecon, type 451005M10T (5.1CFM)
Mfr. Tranyoung, type 6010H05F PF3 (7.08CFM)
Mfr. Forcecon, type DFS450805M10T (3CFM)
MS-163Axx, LGE50,
E500, ED500
Mfr. Forcecon, type 451005M10T (5.1CFM)
Mfr. Forcecon, type DFS450805M10T (3CFM)
Mfr. Tranyoung, type 6010H05F PF3 (7.08CFM)
MS-163Gxxx, MS163Pxxxx
Mfr. Forcecon, type DFS451205M10T (4.5CFM)
Mfr. Forcecon, type 451005M10T (5.1CFM)
Mfr. Tranyoung, type 6010H05F PF3 (7.08CFM)
MS-1034xxxxx,
M660xxxxx,
M662xxxxx, F1, MS1613xxxxx, MS1039xxxxx,
M655xxxxx, LGF1
Mfr. Forcecon, type 451005M10T (5.1CFM)
Mfr. Tranyoung, type 6010H05F PF3 (7.08CFM)
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 18 of 109
Report No.:
11015280 001
Other Remarks:
•
The model MS-163Axx provides one TV tuner card that can be considered as multimedia equipment
under the Guide 112 © IEC:2000. Therefore, the surge test, insulation resistance test and dielectric
strength test were performed according to sub clause 10.1 and 10.3 of IEC 60065 as following test
condition:
- Surge test performed from AC mains of building-in switch power supply to antenna connector of tuner
with 50 discharges at a maximum rate of 12 per minute, from a 1nF capacitor charged to 10kV.
- After the test, the insulation resistance greater then 4 MΩ at 500Vdc and subjected to dielectric strength
test at test voltage 4240 V d.c.
•
Due to fulfilled the following considerations for the equipment, the separation requirements and test of
6.2 are not apply to cable distribution system.
- The circuit of cable distribution system under consideration is TNV-1 circuit.
- The common sides or earthed side of the circuit are connected to the screen of the coaxial cable
through an antenna connector of tuner and to all accessible parts and circuits (SELV and accessible
metal parts).
- The screen of the coaxial cable is intended to be connected to earth in the building installation.
• The similar approach for CB-Scheme testing according to IEC 60950-1:2001, covering German,
USA and Canada. However, in compliance with this requirement for other CB countries verified
during national mark approval.
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 19 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
1
GENERAL
P
1.5
Components
P
1.5.1
General
See below.
P
Comply with IEC 60950 or relevant component
standard
Components, which were found
to affect safety aspects, comply
with the requirements of this
standard or within the safety
aspects of the relevant IEC
component standards (see
appended table 1.5.1).
P
1.5.2
Evaluation and testing of components
Components, which are
certified to IEC and/or national
standards, are used correctly
within their ratings.
Components not covered by
IEC standards are tested under
the conditions present in the
equipment.
P
1.5.3
Thermal controls
No thermal control.
1.5.4
Transformers
Transformers used are suitable
for their intended application
and comply with the relevant
requirements of the standard.
1.5.5
Interconnecting cables
No interconnection cable.
1.5.6
Capacitors in primary circuits ...............................: Equipment is not directly
connected to the AC mains
supply.
N/A
1.5.7
Double insulation or reinforced insulation bridged
by components
N/A
1.5.7.1
General
N/A
1.5.7.2
Bridging capacitors
N/A
1.5.7.3
Bridging resistors
N/A
1.5.7.4
Accessible parts
N/A
1.5.8
Components in equipment for IT power systems
1.6
Power interface
1.6.1
AC power distribution systems
TRF No.:IECEN60950_1B
Result – Remark
No such components.
Equipment is not directly
connected to the AC mains
supply.
Verdict
N/A
P
N/A
N/A
P
Equipment is not directly
connected to the AC mains
supply.
N/A
TRF originator: SGS Fimko
Page 20 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
1.6.2
Input current
Highest load according to
1.2.2.1 for this equipment which
its contains max. rating of the
optional optical drives and HDD
permanently access, brightness
and contrast for LCD back light
circuit and charged with empty
battery pack. Dummy load of
2.5W in connection to represent
the each USB load. The
operator can connect additional
options like a parallel printer or
a serial device. See appended
table 1.6.2. See summary of
testing and appended table.
1.6.3
Voltage limit of hand-held equipment
This appliance is a not hand
held equipment.
N/A
1.6.4
Neutral conductor
Equipment is not directly
connected to the AC mains
supply.
N/A
1.7
Marking and instructions
1.7.1
Power rating
P
P
Marking label is located on
bottom of enclosure.
P
Rated voltage(s) or voltage range(s) (V) .............: See copy of marking plate. (no
direct connection to mains
supply)
N/A
Symbol for nature of supply, for d.c. only .............: D.C. symbol used.
N/A
Rated frequency or rated frequency range (Hz) ..: No direct connection to the AC
mains supply.
N/A
Rated current (mA or A) ......................................: See copy of marking plate. (no
direct connection to mains
supply)
N/A
Manufacturer’s name or trademark or identification See copy of marking plate.
mark .....................................................................:
P
Type/model or type reference...............................: See copy of marking plate.
P
Symbol for Class II equipment only .....................: Class III equipment.
N/A
Other symbols ......................................................: Additional symbols or markings
do not give rise to
misunderstanding.
P
Certification marks ...............................................: See copy of the marking plate.
N/A
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 21 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
1.7.2
Safety instructions
The user’s manual provided
including:
Verdict
P
Operating temperature, adapter
source and
“CAUTION
Danger of explosion if battery is
incorrectly replaced. Replace
only with the same or
equivalent type recommended
by the manufacturer. Dispose
of used batteries according to
the manufacturer’s instruction.”
1.7.3
Short duty cycles
1.7.4
Supply voltage adjustment ...................................: No voltage / Frequency setting.
N/A
Methods and means of adjustment; reference to No outlet.
installation instructions .........................................:
N/A
1.7.5
Power outlets on the equipment ..........................: No outlet.
N/A
1.7.6
Fuse identification (marking, special fusing
Fuse not located in operator
characteristics, cross-reference) .........................: access areas, unambiguous
fuse cross-reference provided.
1.7.7
Wiring terminals
1.7.7.1
Protective earthing and bonding terminals ..........: No direct connection to AC
mains supply.
N/A
1.7.7.2
Terminal for a.c. mains supply conductors
No direct connection to the AC
mains supply.
N/A
1.7.7.3
Terminals for d.c. mains supply conductors
No direct connection to the DC
mains supply.
N/A
1.7.8
Controls and indicators
See below.
1.7.8.1
Identification, location and marking .....................: The marking of the stand-by
switch or functional switch or
indicators were located that
indication of function clearly.
1.7.8.2
Colours ...............................................................: No safety relevant control and
indicator.
1.7.8.3
Symbols according to IEC 60417 .........................: Marking for stand-by type switch
according IEC 60417, No. 5009
(line half inside circle) was
marked on stand-by type switch
button.
1.7.8.4
Markings using figures ........................................:
N/A
1.7.9
Isolation of multiple power sources .....................: No direct connection to AC
mains supply.
N/A
TRF No.:IECEN60950_1B
Equipment designed for
continuous operation.
See below.
N/A
P
N/A
P
P
N/A
P
TRF originator: SGS Fimko
Page 22 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
1.7.10
IT power distribution systems
No direct connection to AC
mains supply.
N/A
1.7.11
Thermostats and other regulating devices
No such devices.
N/A
1.7.12
Language(s) .........................................................: Marking label and operation
manual are in English.

Versions in other languages will
be provided when national
certificate approval.
1.7.13
Durability
The label was subjected to the
permanence of marking test.
The label was rubbed with cloth
soaked with water for 15 s and
then again for 15 s with the
cloth soaked with petroleum
spirit.
P
After this test there was no
damage to the label. The
marking on the label did not
fade. There was neither curling
nor lifting of the label edge.
1.7.14
Removable parts
No required markings placed
on removable parts.
P
1.7.15
Replaceable batteries
The Lithium type RTC battery
and battery pack are
exchangeable. The warning
text provided in user’s manual.
P
Language(s)..........................................................: English.

1.7.16
Operator access with a tool ..................................: No user access area.
N/A
1.7.17
Equipment for restricted access locations ............: Use of equipment not limited to
restricted access locations.
N/A
2
PROTECTION FROM HAZARDS
P
2.1
Protection from electric shock and energy hazards
P
2.1.1
Protection in operator access areas
See below.
P
2.1.1.1
Access to energized parts
See below.
P
Test by inspection ................................................: The notebook PC is supplied
from an approved SPS adaptor
or battery pack that provides
only SELV.
P
Test with test finger ..............................................: No access with test finger to any
parts with only basic insulation
to TNV-3.
P
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 23 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
Test with test pin ..................................................: The test pin can not touch TNV3 circuit through any seams
within the appliance.
P
Test with test probe .............................................: The test probe cannot touch
pins of connector of TNV-3
circuit through any seams within
the appliance.
P
2.1.1.2
Battery compartments .........................................: TNV circuits are not accessible
when replacing battery pack.
P
2.1.1.3
Access to ELV wiring
The Lithium type RTC battery
and battery pack are
exchangeable. The warning
text provided in user’s manual.
Working voltage (Vpeak or Vrms); minimum
distance (mm) through insulation

2.1.1.4
Access to hazardous voltage circuit wiring
2.1.1.5
Energy hazards ....................................................: No energy hazard in operator
access area. The connectors on
the backside of the equipment
below 240VA.
2.1.1.6
Manual controls
2.1.1.7
Discharge of capacitors in equipment
No hazardous voltage wiring in
operator accessible area.
No conductive shafts of
operating knobs and handles.
Protection in service access areas
2.1.3
Protection in restricted access locations
2.2
SELV circuits
N/A
P
N/A
N/A
Time-constant (s); measured voltage (V) .............:
2.1.2
N/A

N/A
The unit not intended to be used
in restricted locations.
N/A
P
Supply from an approved SPS adapter was considered to carry SELV at below
240VA only. No higher voltages generated.
2.2.1
General requirements
2.2.2
Voltages under normal conditions (V) ..................: 42.4V peak or 60Vd.c. are not
exceeded in SELV circuit under
normal operation.
TRF No.:IECEN60950_1B
The secondary circuits were
tested as SELV. See 2.2.1 to
2.2.4.
P
P
TRF originator: SGS Fimko
Page 24 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
2.2.3
Voltages under fault conditions (V).......................: Single fault did not cause
excessive voltage in accessible
SELV circuits. Limits of 71V
peak and 120Vd.c. were not
exceeded within 0.2 s and
limits 42.4V peak and 60Vd.c.
were not exceeded for longer
than 0.2 seconds.
2.2.3.1
Separation by double insulation or reinforced
insulation (method 1)
2.2.3.2
Separation by earthed screen (method 2)
N/A
2.2.3.3
Protection by earthing of the SELV circuit
(method 3)
N/A
2.2.4
Connection of SELV circuits to other circuits........: See 2.2.2, 2.2.3 and 2.4.3.
P
2.3
TNV circuits
P
Class III equipment.
Verdict
P
N/A
The Cable distribution system consider to comply with TNV-1 circuit.
2.3.1
2.3.2
2.3.3
2.3.4
Limits
The modem module is an
approved component that
generates only signals within the
limits of SELV circuits. The
telecommunication network is
considered to be TNV-3 circuit.
Type of TNV circuits .............................................: Same above.

Separation from other circuits and from accessible Supplementary insulation
parts
between TNV and SELV
provided. Requirements of 6.2.2
are applicable.
P
Insulation employed..............................................: Same above.

Separation from hazardous voltages
Both TNV separated to primary
by reinforced or double
insulation by the certified power
adapter. TNV circuit only
connected to SELV circuit.
N/A
Insulation employed..............................................: Same above.

Connection of TNV circuits to other circuits
P
Both TNV separated to primary
by reinforced or double
insulation by the certified power
adapter. TNV circuit only
connected to SELV circuit.
Insulation employed..............................................: Same above.
2.3.5
P
Test for operating voltages generated externally
TRF No.:IECEN60950_1B

Supplementary insulation
provided. No test for this clause.
N/A
TRF originator: SGS Fimko
Page 25 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
2.4
Limited current circuits
2.4.1
General requirements
Considered.
P
2.4.2
Limit values
See below.
P
P
Frequency (Hz) .....................................................: (Refer to the appended table)

Measured current (mA).........................................: (Refer to the appended table)

Measured voltage (V) ...........................................: 1.34kV max.

Measured capacitance (µF) ..................................: For Sample/YIVNMS0018D11-and YIVNMS0020D11-- =
270pF

For Mitac/DA-1A08-MS02L---,
Mitac/DA-1A08-MS01L--- and
DA-1A08-MS01 L= 100pF
For Sample/YIVNMS0018D11B = 150pF
For Sample/YIVNMS0018D11A and YIVNMS0020D11-A =
180pF
For others Max. 68pF
2.4.3
Connection of limited current circuits to other
circuits
2.5
Limited power sources
Limited current circuits are
supplied from SELV and meet
2.4.1 to 2.4.2 under normal and
single fault condition.
P
P
Test for output of USB ports.
Inherently limited output
Impedance limited output
2.6
N/A
Results see appended table
2.5.
P
Overcurrent protective device limited output
N/A
Regulating network limited output under normal
operating and single fault condition
N/A
Regulating network limited output under normal
operating conditions and overcurrent protective
device limited output under single fault condition
N/A
Output voltage (V), output current (A), apparent
Results see appended table
power (VA)............................................................: 2.5.

Current rating of overcurrent protective device (A)

Provisions for earthing and bonding
N/A
Class III equipment
2.6.1
Protective earthing
TRF No.:IECEN60950_1B
N/A
TRF originator: SGS Fimko
Page 26 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
2.6.2
Functional earthing
N/A
2.6.3
Protective earthing and protective bonding
conductors
N/A
2.6.3.1
General
N/A
2.6.3.2
Size of protective earthing conductors
N/A
2
Rated current (A), cross-sectional area (mm ),
AWG .....................................................................:
2.6.3.3
Verdict

Size of protective bonding conductors
N/A
2
Rated current (A), cross-sectional area (mm ),
AWG .....................................................................:

2.6.3.4
Resistance (Ω) of earthing conductors and their
terminations, test current (A) ................................:
N/A
2.6.3.5
Colour of insulation ...............................................:
N/A
2.6.4
Terminals
N/A
2.6.4.1
General
N/A
2.6.4.2
Protective earthing and bonding terminals
N/A
Rated current (A), type and nominal thread
diameter (mm) ......................................................:

2.6.4.3
Separation of the protective earthing conductor
from protective bonding conductors
N/A
2.6.5
Integrity of protective earthing
N/A
2.6.5.1
Interconnection of equipment
N/A
2.6.5.2
Components in protective earthing conductors
and protective bonding conductors
N/A
2.6.5.3
Disconnection of protective earth
N/A
2.6.5.4
Parts that can be removed by an operator
N/A
2.6.5.5
Parts removed during servicing
N/A
2.6.5.6
Corrosion resistance
N/A
2.6.5.7
Screws for protective bonding
N/A
2.6.5.8
Reliance on telecommunication network or cable
distribution system
N/A
2.7
Overcurrent and earth fault protection in primary circuits
N/A
With SELV supply from approved AC adapter or battery pack, no primary circuits
inside.
2.7.1
Basic requirements
N/A
Instructions when protection relies on building
installation
N/A
2.7.2
Faults not covered in 5.3
N/A
2.7.3
Short-circuit backup protection
N/A
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 27 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
2.7.4
Number and location of protective devices ..........:
N/A
2.7.5
Protection by several devices
N/A
2.7.6
Warning to service personnel ...............................:
N/A
2.8
Safety interlocks
N/A
2.8.1
General principles
N/A
2.8.2
Protection requirements
N/A
2.8.3
Inadvertent reactivation
N/A
2.8.4
Fail-safe operation
N/A
2.8.5
Moving parts
N/A
2.8.6
Overriding
N/A
2.8.7
Switches and relays
N/A
2.8.7.1
Contact gaps (mm) ..............................................:
N/A
2.8.7.2
Overload test
N/A
2.8.7.3
Endurance test
N/A
2.8.7.4
Electric strength test
N/A
2.8.8
Mechanical actuators
N/A
2.9
Electrical insulation
P
The unit is supplied from an approved power supply or battery pack that provides
SELV. Only SELV, limited current circuit and approved modem module with TNV
inside the unit.
2.9.1
Properties of insulating materials
Natural rubber, asbestos or
hygroscopic material is not
used.
P
2.9.2
Humidity conditioning
120 hours
P
Humidity (%) ........................................................: 95% R.H.

Temperature (°C) .................................................: 40°C

2.9.3
Grade of insulation
P
2.10
Clearances, creepage distances and distances through insulation
The adequate levels of safety
insulation is provided and
maintained to comply with the
requirements of this standard.
P
The unit is supplied from an approved power supply or battery pack that provides
SELV. Only SELV, limited current circuit and approved modem module with TNV
inside the unit.
2.10.1
General
TRF No.:IECEN60950_1B
See 2.10.3, 2.10.4 and 2.10.5.
P
TRF originator: SGS Fimko
Page 28 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
2.10.2
Determination of working voltage
Working voltage is considered
to be within the TNV-3
parameters with Udc≤120V,
Uac≤70.7Vpk.
Verdict
P
Therefore the following values
have been used for tables 2K
and 2L:
Udc≤125V used in table 2L,
Udc≤140V used in table 2K.
2.10.3
Clearances
See below and advantage of
annex G is not considered.
P
2.10.3.1
General
See below.
P
2.10.3.2
Clearances in primary circuits
No primary circuit.
2.10.3.3
Clearances in secondary circuits
Considered.
2.10.3.4
Measurement of transient voltage levels
No transient voltage across the
clearance lower than due or
normal.
N/A
2.10.4
Creepage distances
See appended table 2.10.3 and
2.10.4.
P
N/A
P
CTI tests ...............................................................: CTI rating for all materials of
min. 100.

2.10.5
Solid insulation
See below.
P
2.10.5.1
Minimum distance through insulation
See appended table 2.10.5.
P
2.10.5.2
Thin sheet material
The modem card was covered
completely by mylar sheet.
P
2.10.5.3
Number of layers (pcs) .........................................: 2 layers

Electric strength test

1500Va.c. at each layer
Printed boards
N/A
Distance through insulation
N/A
Electric strength test for thin sheet insulating
material

Number of layers (pcs) .........................................:
N/A
Wound components
N/A
Number of layers (pcs) .........................................:
N/A
Two wires in contact inside wound component;
angle between 45° and 90° ..................................:
N/A
2.10.6
Coated printed boards
N/A
2.10.6.1
General
N/A
2.10.6.2
Sample preparation and preliminary inspection
N/A
2.10.5.4
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 29 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
2.10.6.3
Thermal cycling
N/A
2.10.6.4
Thermal ageing (°C) .............................................:
N/A
2.10.6.5
Electric strength test
2.10.6.6
Abrasion resistance test

N/A
Electric strength test
2.10.7
2.10.8
Verdict

Enclosed and sealed parts ...................................:
N/A
Temperature T1=T2 + Tma – Tamb +10K (°C)....:
N/A
Spacings filled by insulating compound................:
N/A
Electric strength test

2.10.9
Component external terminations
N/A
2.10.10
Insulation with varying dimensions
N/A
3
WIRING, CONNECTIONS AND SUPPLY
P
3.1
General
P
3.1.1
Current rating and overcurrent protection
All internal wires are UL
recognized wiring which is PVC
insulated, rated VW-1, min.
80°C. Internal wiring gauge is
suitable for current intended to
be carried
P
3.1.2
Protection against mechanical damage
Wires do not touch sharp
edges and heatsinks which
could damage the insulation
and cause hazard.
P
3.1.3
Securing of internal wiring
The wires are secured by
soldering and quick connector
so that a loosening of the
terminal connection is unlikely.
P
3.1.4
Insulation of conductors
The insulation of the individual
conductors is suitable for the
application and the working
voltage. For the insulation
material see 3.1.1.
P
3.1.5
Beads and ceramic insulators
Not used.
N/A
3.1.6
Screws for electrical contact pressure
No such screws.
N/A
3.1.7
Insulating materials in electrical connections
3.1.8
Self-tapping and spaced thread screws
No self- tapping or spaced
thread screws used.
N/A
3.1.9
Termination of conductors
All conductors are reliably
secured.
P
10 N pull test
Applied and passed.
P
TRF No.:IECEN60950_1B
N/A
TRF originator: SGS Fimko
Page 30 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
3.1.10
Sleeving on wiring
Heatshrinkable tube used as
supplementary insulation on
wiring to RJ-11 connector.
3.2
Connection to an a.c. mains supply or a d.c. mains supply
Verdict
P
N/A
No direct connection to the AC or DC mains supply.
3.2.1
Means of connection ............................................:
N/A
3.2.1.1
Connection to an a.c. mains supply
N/A
3.2.1.2
Connection to a d.c. mains supply
N/A
3.2.2
Multiple supply connections
N/A
3.2.3
Permanently connected equipment
N/A
Number of conductors, diameter (mm) of cable
and conduits ........................................................:

3.2.4
Appliance inlets
N/A
3.2.5
Power supply cords
N/A
3.2.5.1
AC power supply cords
N/A
Type......................................................................:
2
Rated current (A), cross-sectional area (mm ),
AWG .....................................................................:


3.2.5.2
DC power supply cords
N/A
3.2.6
Cord anchorages and strain relief
N/A
Mass of equipment (kg), pull (N) ........................:

Longitudinal displacement (mm) ..........................:

3.2.7
Protection against mechanical damage
N/A
3.2.8
Cord guards
N/A
D (mm); test mass (g) ..........................................:

Radius of curvature of cord (mm).........................:

3.2.9
Supply wiring space
N/A
3.3
Wiring terminals for connection of external conductors
N/A
Class III equipment.
3.3.1
Wiring terminals
N/A
3.3.2
Connection of non-detachable power supply
cords
N/A
3.3.3
Screw terminals
N/A
3.3.4
Conductor sizes to be connected
N/A
Rated current (A), cord/cable type, cross-sectional
2
area (mm )............................................................:
TRF No.:IECEN60950_1B

TRF originator: SGS Fimko
Page 31 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
3.3.5
Wiring terminal sizes
Result – Remark
Verdict
N/A
Rated current (A), type and nominal thread
diameter (mm) .....................................................:

3.3.6
Wiring terminals design
N/A
3.3.7
Grouping of wiring terminals
N/A
3.3.8
Stranded wire
N/A
3.4
Disconnection from the mains supply
N/A
No direct connection to the AC or DC mains supply.
3.4.1
General requirement
N/A
3.4.2
Disconnect devices
N/A
3.4.3
Permanently connected equipment
N/A
3.4.4
Parts which remain energized
N/A
3.4.5
Switches in flexible cords
N/A
3.4.6
Single-phase equipment and d.c. equipment
N/A
3.4.7
Three-phase equipment
N/A
3.4.8
Switches as disconnect devices
N/A
3.4.9
Plugs as disconnect devices
N/A
3.4.10
Interconnected equipment
N/A
3.4.11
Multiple power sources
N/A
3.5
Interconnection of equipment
3.5.1
General requirements
3.5.2
Types of interconnection circuits ..........................: Interconnection circuits of
SELV, LCC and TNV through
the connectors.
3.5.3
ELV circuits as interconnection circuits
4
PHYSICAL REQUIREMENTS
P
4.1
Stability
P
Angle of 10°
P
See below.
P
N/A
This appliance is of a stable
mechanical construction and
does not overbalance when
tilted to an angle of 10° from
its normal upright position with
and without LCD screen open
conditions.
Test: force (N).......................................................: Equipment is not a
floorstanding unit.
TRF No.:IECEN60950_1B
P
P
N/A
TRF originator: SGS Fimko
Page 32 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
4.2
Mechanical strength
4.2.1
General
See below. After tests, unit
comply with 2.1.1, 2.10 and
4.4.1.
P
4.2.2
Steady force test, 10 N
10N applied to components
other than parts serving as an
enclosure.
P
4.2.3
Steady force test, 30 N
30N applied to internal
enclosure when removed
battery pack. No energy or other
hazards.
P
4.2.4
Steady force test, 250 N
250N applied to outer enclosure
of notebook PC and battery
pack. No energy or other
hazards.
P
4.2.5
Impact test
Transportable equipment.
N/A
Fall test
Transportable equipment.
N/A
Swing test
Transportable equipment.
N/A
4.2.6
Drop test
After the test, no hazards.
P
4.2.7
Stress relief test
After 7hrs for Notebook PC and
battery pack enclosure at 79°C
cooling down to room
temperature, no shrinkage,
distortion or loosing of enclosure
of battery pack and notebook
PC was noticeable on this
equipment.
P
4.2.8
Cathode ray tubes
No CRT.
P
N/A
Picture tube separately certified ...........................:
N/A
4.2.9
High pressure lamps
4.2.10
Wall or ceiling mounted equipment; force (N) .....:
4.3
Design and construction
4.3.1
Edges and corners
4.3.2
Handles and manual controls; force (N) ...............:
N/A
4.3.3
Adjustable controls
N/A
4.3.4
Securing of parts
TRF No.:IECEN60950_1B
No high pressure lamp.
N/A
N/A
P
Edges and corners of the
enclosure are rounded.
Electrical and mechanical
connections can be expected
to withstand usual mechanical
stress. For the protection
solder pins are used.
P
P
TRF originator: SGS Fimko
Page 33 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
4.3.5
Connection of plugs and sockets
Mismatch of connectors were
prevented by incompatible form
or location.
4.3.6
Direct plug-in equipment
Not direct plug-in type.
N/A
Dimensions (mm) of mains plug for direct plug-in : Not direct plug-in type.
N/A
Torque and pull test of mains plug for direct
Not direct plug-in type.
plug-in; torque (Nm); pull (N) ................................:
N/A
4.3.7
Heating elements in earthed equipment
N/A
4.3.8
Batteries
Battery packs are approved
components and used within
their specified rating and no
reverse polarity installation could
happen due to design of pack.
Verdict
P
P
For non-rechargable lithium type
RTC battery:
•
There is no reverse polarity
installation possible due to
design of socket.
•
The battery is protected
from reverse charging by
diode and resistor.
Results see appended table
5.3.
4.3.9
Oil and grease
No oil or grease.
N/A
4.3.10
Dust, powders, liquids and gases
The equipment is intended use
not considered to be exposed to
dust, powers, liquids and gases.
N/A
4.3.11
Containers for liquids or gases
No container for liquid or gas.
N/A
4.3.12
Flammable liquids.................................................: No flammable liquid.
N/A
Quantity of liquid (l) ...............................................:
N/A
Flash point (°C).....................................................:
N/A
4.3.13
Radiation; type of radiation ..................................: See below.
P
4.3.13.1
General
See below.
P
4.3.13.2
Ionizing radiation
No ionizing radiation.
4.3.13.3
N/A
Measured radiation (pA/kg) .................................:

Measured high-voltage (kV) ................................:

Measured focus voltage (kV) ...............................:

CRT markings .....................................................:

Effect of ultraviolet (UV) radiation on materials
TRF No.:IECEN60950_1B
No UV radiation.
N/A
TRF originator: SGS Fimko
Page 34 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
Part, property, retention after test, flammability
classification ........................................................:
N/A
4.3.13.4
Human exposure to ultraviolet (UV) radiation ......:
N/A
4.3.13.5
Laser (including LEDs)
LED power is far below LED
Class 1 limit.
P
All optional optical drives were
evaluated according to relevant
standard for laser product.
Therefore, complied with this
clause without further test.
Class 1 laser symbol appeared
on all optional optical drives and
in user’s manual.
Laser class ...........................................................: Laser Class 1 for all optional
optical drives.

4.3.13.6
Other types ..........................................................: No other types radiation.
4.4
Protection against hazardous moving parts
4.4.1
General
DC fan is protected by
enclosure. Other motors are
used in the certified HDD and all
optional optical drives.
P
4.4.2
Protection in operator access areas
No hazardous moving parts
within operator access areas.
P
4.4.3
Protection in restricted access locations
Not limited for restricted access
locations.
4.4.4
Protection in service access areas
4.5
Thermal requirements
4.5.1
Maximum temperatures
P
Resistance to abnormal heat
4.6
Openings in enclosures
4.6.1
Top and side openings
P
See appended table 4.5.1.
Bottoms of fire enclosures
N/A
P
Transportable equipment.
Same as above.
Construction of the bottom ...................................: Same as above.
4.6.3
Doors or covers in fire enclosures
TRF No.:IECEN60950_1B
P
P
Dimensions (mm) ................................................: Same as above.
4.6.2
N/A
N/A
Normal load condition per Annex L.......................: See 1.6.2.
4.5.2
N/A
No doors or covers which
leading to an operator access
area.
N/A

N/A

N/A
TRF originator: SGS Fimko
Page 35 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
4.6.4
Openings in transportable equipment
See appended table 4.6.1 and
4.6.2.
P
4.6.5
Adhesives for constructional purposes
No barrier secured by adhesive
inside enclosure.
N/A
Conditioning temperature (°C)/time (weeks) ........: No barrier secured by adhesive
inside encloure

4.7
Resistance to fire
P
4.7.1
Reducing the risk of ignition and spread of flame
See below.
P
Method 1, selection and application of
components wiring and materials
Use of materials with the
required flammability classes.
P
Method 2, application of all of simulated fault
condition tests
N/A
4.7.2
Conditions for a fire enclosure
See below.
P
4.7.2.1
Parts requiring a fire enclosure
With having the following parts:
P
•
Components in secondary
(not supplied by LPS)
•
Insulated wiring
The fire enclosure is required.
4.7.2.2
Parts not requiring a fire enclosure
4.7.3
Materials
4.7.3.1
General
See appended table 1.5.1 for
PCB material.
P
4.7.3.2
Materials for fire enclosures
See appended table 1.5.1 for
enclosure material.
P
4.7.3.3
Materials for components and other parts outside
fire enclosures
4.7.3.4
Materials for components and other parts inside
fire enclosures
Internal components except
small parts are V-2, HF-2 or
better.
4.7.3.5
Materials for air filter assemblies
No air filter assemblies.
N/A
4.7.3.6
Materials used in high-voltage components
No high voltage component.
N/A
5
ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS
P
5.1
Touch current and protective conductor current
P
5.1.1
General
5.1.2
Equipment under test (EUT)
5.1.3
Test circuit
5.1.4
Application of measuring instrument
TRF No.:IECEN60950_1B
See clasue 4.7.2.1.
N/A
P
N/A
See below.
P
P
N/A
Using figure 5A.
P
N/A
TRF originator: SGS Fimko
Page 36 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
5.1.5
Test procedure
Approved adapter used.
N/A
5.1.6
Test measurements
Approved adapter used.
N/A
Test voltage (V) ...................................................: See 5.1.8.1.

Measured touch current (mA) ..............................: See 5.1.8.1.

Max. allowed touch current (mA) .........................: See 5.1.8.1.

Measured protective conductor current (mA) ......:

Max. allowed protective conductor current (mA) .:

5.1.7
Equipment with touch current exceeding 3.5 mA :
N/A
5.1.8
Touch currents to and from telecommunication
See below.
networks and cable distribution systems and from
telecommunication networks
P
5.1.8.1
Limitation of the touch current to a
telecommunication network and a cable
distribution system
P
See below
Test voltage (V) ...................................................: 264V for adapter

19V for notebook PC
Measured touch current (mA) ..............................: See appended table.

Max. allowed touch current (mA) .........................: 0.25

5.1.8.2
Summation of touch currents from
telecommunication networks ................................:
N/A
5.2
Electric strength
N/A
Class III equipment.
5.2.1
General
N/A
5.2.2
Test procedure
N/A
5.3
Abnormal operating and fault conditions
5.3.1
Protection against overload and abnormal
operation
See below.
P
5.3.2
Motors
Certified DC fans used, see
table 1.5.1 for detail.
P
P
Other motors are used in the
appliances that are certified
HDD and all optional optical
drives, see appended table
1.5.1.
5.3.3
Transformers
5.3.4
Functional insulation .............................................: Method c). Results see
appended table 5.3.
TRF No.:IECEN60950_1B
No safety isolation transformer.
N/A
P
TRF originator: SGS Fimko
Page 37 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
5.3.5
Electromechanical components
No electromechanical
component.
5.3.6
Simulation of faults
See appended table.
5.3.7
Unattended equipment
None of the listed components
was provided.
5.3.8
Compliance criteria for abnormal operating and
fault conditions
No fire occurred. No molten
metal was emitted.
6
CONNECTION TO TELECOMMUNICATION NETWORKS
P
6.1
Protection of telecommunication network service persons, and users of other
equipment connected to the network, from hazards in the equipment
P
6.1.1
Protection from hazardous voltages
P
6.1.2
Separation of the telecommunication network from earth
N/A
6.1.2.1
Requirements
N/A
Supplementary insulation
provided between TNV-3 circuit
and SELV circuit.
Verdict
N/A
P
N/A
P
Test voltage (V) ...................................................: Results see appended table
6.2.2.2.

Current in the test circuit (mA) ............................:

6.1.2.2
Exclusions.............................................................:
N/A
6.2
Protection of equipment users from overvoltages on telecommunication networks
P
6.2.1
Separation requirements
P
Adequate electrical separation
between TNV-3 to
-
Keyboard or external
enclosure
-
User accessible connectors
-
SELV circuits
6.2.2
Electric strength test procedure
6.2.2.1
Impulse test
P
6.2.2.2
Steady-state test
P
6.2.2.3
Compliance criteria
6.3
Protection of the telecommunication wiring system from overheating
7
See appended table.
Complied.
P
P
N/A
Max. output current (A) .........................................:

Current limiting method ........................................:

CONNECTION TO CABLE DISTRIBUTION SYSTEMS
P
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 38 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
7.1
Protection of cable distribution system service
persons, and users of other equipment
connected to the system, from hazardous
voltages in the equipment
Circuits in the equipment
intended to be directly connect
to a cable distribution system
which consider to comply with
requirements for TNV-1 circuit
P
7.2
Protection of equipment users from overvoltages
on the cable distribution system
See the page 15, 17
P
7.3
Insulation between primary circuits and cable
distribution systems
See below.
P
7.3.1
General
See below
P
7.3.2
Voltage surge test
Test applied between the AC
mains and the antenna
connection points of TV card
(without earthed connection).
P
After the test, the insulation in
comply with the electric
strength test requirement of
5.2.2.
7.3.3
Impulse test
4 kV of test voltage applied
between the AC mains and the
antenna connection points of
TV card (without earthed
connection).
P
After the test, the insulation in
comply with the electric
strength test requirement of
5.2.2.
A
ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE
A.1
Flammability test for fire enclosures of movable equipment having a total mass
exceeding 18 kg, and of stationary equipment (see 4.7.3.2)
A.1.1
Samples................................................................:

Wall thickness (mm) .............................................:

A.1.2
Conditioning of samples; temperature (°C) ..........:
N/A
A.1.3
Mounting of samples ............................................:
N/A
A.1.4
Test flame (see IEC 60695-11-3)
N/A
Flame A, B, C or D ...............................................:
P
N/A

A.1.5
Test procedure
N/A
A.1.6
Compliance criteria
N/A
Sample 1 burning time (s) ....................................:

Sample 2 burning time (s) ....................................:

Sample 3 burning time (s) ....................................:

TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 39 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
A.2
Flammability test for fire enclosures of movable equipment having a total mass not
exceeding 18 kg, and for material and components located inside fire enclosures
(see 4.7.3.2 and 4.7.3.4)
P
A.2.1
Samples, material.................................................:

Wall thickness (mm) .............................................:

A.2.2
Conditioning of samples
N/A
A.2.3
Mounting of samples ...........................................:
N/A
A.2.4
Test flame (see IEC 60695-11-4)
N/A
Flame A, B or C ...................................................:

A.2.5
Test procedure
N/A
A.2.6
Compliance criteria
N/A
A.2.7
Sample 1 burning time (s) ....................................:

Sample 2 burning time (s) ....................................:

Sample 3 burning time (s) ....................................:

Alternative test acc. to IEC 60695-2-2, cl. 4 and 8
N/A
Sample 1 burning time (s) ....................................:

Sample 2 burning time (s) ....................................:

Sample 3 burning time (s) ....................................:

A.3
Hot flaming oil test (see 4.6.2)
N/A
A.3.1
Mounting of samples
N/A
A.3.2
Test procedure
N/A
A.3.3
Compliance criterion
N/A
B
ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see 4.7.2.2 and
5.3.2)
N/A
B.1
General requirements
N/A
Approved DC Fan, all optional
optical drives and HDD used.
Position ................................................................:

Manufacturer ........................................................:

Type .....................................................................:

Rated values .......................................................:

B.2
Test conditions
N/A
B.3
Maximum temperatures
N/A
B.4
Running overload test
N/A
B.5
Locked-rotor overload test
N/A
Test duration (days) .............................................:

Electric strength test: test voltage (V) ..................:

TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 40 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
B.6
Running overload test for d.c. motors in
secondary circuits
N/A
B.7
Locked-rotor overload test for d.c. motors in secondary circuits
N/A
B.7.1
Test procedure
N/A
B.7.2
Alternative test procedure; test time (h)................:
N/A
B.7.3
Electric strength test
N/A
B.8
Test for motors with capacitors
N/A
B.9
Test for three-phase motors
N/A
B.10
Test for series motors
N/A
Operating voltage (V) ...........................................:
C
Verdict

ANNEX C, TRANSFORMERS (see 1.5.4 and 5.3.3)
N/A
Position ................................................................:

Manufacturer ........................................................:

Type .....................................................................:

Rated values .......................................................:

Method of protection .............................................:

C.1
Overload test
N/A
C.2
Insulation
N/A
Protection from displacement of windings ............:
N/A
D
ANNEX D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS
(see 5.1.4)
P
D.1
Measuring instrument
P
D.2
Alternative measuring instrument
N/A
E
ANNEX E, TEMPERATURE RISE OF A WINDING (see 1.4.13)
N/A
F
ANNEX F, MEASUREMENT OF CLEARANCES AND CREEPAGE DISTANCES
(see 2.10)
G
ANNEX G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM
CLEARANCES
N/A
G.1
Summary of the procedure for determining
minimum clearances
N/A
G.2
Determination of mains transient voltage (V) .......:
N/A
G.2.1
AC mains supply
N/A
TRF No.:IECEN60950_1B
Complied.
P
TRF originator: SGS Fimko
Page 41 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
G.2.2
DC mains supply
N/A
G.3
Determination of telecommunication network
transient voltage (V)..............................................:
N/A
G.4
Determination of required withstand voltage (V)...:
N/A
G.5
Measurement of transient levels (V).....................:
N/A
G.6
Determination of minimum clearances .................:
N/A
H
ANNEX H, IONIZING RADIATION (see 4.3.13)
N/A
J
ANNEX J, TABLE OF ELECTROCHEMICAL POTENTIALS (see 2.6.5.6)
N/A
Metal used ...........................................................:
Verdict

K
ANNEX K, THERMAL CONTROLS (see 1.5.3 and 5.3.7)
N/A
K.1
Making and breaking capacity
N/A
K.2
Thermostat reliability; operating voltage (V) .........:
N/A
K.3
Thermostat endurance test; operating voltage
(V) .......................................................................:
N/A
K.4
Temperature limiter endurance; operating voltage
(V) ........................................................................:
N/A
K.5
Thermal cut-out reliability
N/A
K.6
Stability of operation
N/A
L
ANNEX L, NORMAL LOAD CONDITIONS FOR SOME TYPES OF ELECTRICAL
BUSINESS EQUIPMENT (see 1.2.2.1 and 4.5.1)
L.1
Typewriters
N/A
L.2
Adding machines and cash registers
N/A
L.3
Erasers
N/A
L.4
Pencil sharpeners
N/A
L.5
Duplicators and copy machines
N/A
L.6
Motor-operated files
N/A
L.7
Other business equipment
M
ANNEX M, CRITERIA FOR TELEPHONE RINGING SIGNALS (see 2.3.1)
N/A
M.1
Introduction
N/A
M.2
Method A
N/A
M.3
Method B
N/A
M.3.1
Ringing signal
N/A
TRF No.:IECEN60950_1B
See 1.6.2.
P
P
TRF originator: SGS Fimko
Page 42 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
M.3.1.1
Frequency (Hz) ....................................................:

M.3.1.2
Voltage (V) ...........................................................:

M.3.1.3
Cadence; time (s), voltage (V) .............................:

M.3.1.4
Single fault current (mA) .......................................:

M.3.2
Tripping device and monitoring voltage ................:
N/A
M.3.2.1
Conditions for use of a tripping device or a
monitoring voltage
N/A
M.3.2.2
Tripping device
N/A
M.3.2.3
Monitoring voltage (V)...........................................:
N/A
N
ANNEX N, IMPULSE TEST GENERATORS (see 2.10.3.4, 6.2.2.1, 7.3.2 and
clause G.5)
P
N.1
ITU-T impulse test generators
P
N.2
IEC 60065 impulse test generator
P
ANNEX P, NORMATIVE REFERENCES
P
Q
ANNEX Q, BIBLIOGRAPHY
P
R
ANNEX R, EXAMPLES OF REQUIREMENTS FOR QUALITY CONTROL
PROGRAMMES
N/A
R.1
Minimum separation distances for unpopulated
coated printed boards (see 2.10.6)
N/A
R.2
Reduced clearances (see 2.10.3)
N/A
S
ANNEX S, PROCEDURE FOR IMPULSE TESTING (see 6.2.2.3)
N/A
S.1
Test equipment
N/A
S.2
Test procedure
N/A
S.3
Examples of waveforms during impulse testing
N/A
T
ANNEX T, GUIDANCE ON PROTECTION AGAINST INGRESS OF WATER
(see 1.1.2)
N/A
N/A

U
ANNEX U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED
INSULATION (see 2.10.5.4)
N/A

TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 43 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
V
ANNEX V, AC POWER DISTRIBUTION SYSTEMS (see 1.6.1)
N/A
V.1
Introduction
N/A
V.2
TN power distribution systems
N/A
V.3
TT power systems
N/A
V.4
IT power systems
N/A
W
ANNEX W, SUMMATION OF TOUCH CURRENTS
N/A
W.1
Touch current from electronic circuits
N/A
W.1.2
Earthed circuits
N/A
W.2
Interconnection of several equipments
N/A
W.2.1
Isolation
N/A
W.2.2
Common return, isolated from earth
N/A
W.2.3
Common return, connected to protective earth
N/A
X
ANNEX X, MAXIMUM HEATING EFFECT IN TRANSFORMER TESTS
(see clause C.1)
N/A
X.1
Determination of maximum input current
N/A
X.2
Overload test procedure
N/A
Y
ANNEX Y, ULTRAVIOLET LIGHT CONDITIONING TEST (see 4.3.13.3)
N/A
Y.1
Test apparatus .....................................................:
N/A
Y.2
Mounting of test samples .....................................:
N/A
Y.3
Carbon-arc light-exposure apparatus ..................:
N/A
Y.4
Xenon-arc light exposure apparatus ....................:
N/A
TRF No.:IECEN60950_1B
Result – Remark
Verdict
TRF originator: SGS Fimko
Page 44 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
CENELEC COMMON MODIFICATIONS [C],
SPECIAL NATIONAL CONDITIONS [S] AND A-DEVIATIONS (NATIONAL DEVIATIONS) [A]
(EN 60950-1:2001, Annex ZB and Annex ZC)
General
C: Delete all the "country" notes in the reference
document according to the following list:
1.1.5
Note 2
1.7.2
Note 4
2.2.3
Note
2.3.3
Note 1, 2
2.10.3.1 Note 4
3.2.5.1 Note 2
4.7.3.1 Note 2
6.2.2
Note
7
Note 4
G2.1
Note 1, 2
1.5.8
1.7.12
2.2.4
2.3.4
3.2.1.1
4.3.6
6.1.2.1
6.2.2.1
7.1
Annex H
Note 2
Note 2
Note
Note 2,3
Note
Note 1,2
Note
Note 2
Note
Note 2
1.6.1
2.6
2.3.2
2.7.1
3.2.3
4.7.2.2
6.1.2.2
6.2.2.2
Deleted.
Verdict
P
P
Note
Note
Note 2, 7, 8
Note
Note 1, 2
Note
Note
Note
1.2.4.1
S (DK): Certain types of Class I appliances (see
3.2.1.1) may be provided with a plug not
establishing earthing conditions when inserted
into Danish socket-outlets.
No direct connection to the AC
mains supply.
N/A
1.5.1
A (SE, Ordinance 1990:944 and
CH, Ordinance on environmentally hazardous
substances SR 814.013, Annex 3.2, Mercury):
Add NOTE – Switches containing mercury such as
No such switch.
N/A
thermostats, relays and level controllers are not allowed.
1.5.8
S (NO): Due to the IT power system used (see
annex V, Fig. V.7), capacitors are required to be
rated for the applicable line-to-line voltage
(230 V).
Class III equipment.
N/A
1.7.2
S (FI, NO, SE): CLASS I PLUGGABLE EQUIPMENT
intended for connection to other
equipment or a network shall, if safety relies on
connection to protective earth or if surge
suppressors are connected between the network
terminals and accessible parts, have a marking
stating that the equipment must be connected to
an earthed mains socket-outlet.
Class III equipment. (for all
models except for MS-163Axx)
N/A
TYPE A
Not applied for. (for model: MS163Axx only)
The marking text in the applicable countries shall
be as follows:
FI: "Laite on liitettävä suojamaadoituskoskettimilla Class III equipment. (for all
varustettuun pistorasiaan"
models except for MS-163Axx)
N/A
Not applied for. (for model: MS163Axx only)
NO: "Apparatet må tilkoples jordet stikkontakt"
Class III equipment. (for all
models except for MS-163Axx)
N/A
Not applied for. (for model: MS163Axx only)
SE: "Apparaten skall anslutas till jordat uttag"
Class III equipment. (for all
models except for MS-163Axx)
N/A
Not applied for. (for model: MS163Axx only)
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 45 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
A (DK, Heavy Current Regulations): Supply cords Class III equipment.
of class I equipment, which is delivered without a
plug, must be provided with a visible tag with the
following text:
Verdict
N/A
Vigtigt!
Lederen med grøn/gul isolation må kun tilsluttes
en klemme mærket
eller
If essential for the safety of the equipment, the
tag must in addition be provided with a diagram
which shows the connection of the other
conductors, or be provided with the following text:
"For tilslutning af de øvrige ledere, se
medfølgende instalationsvejledning."
1.7.5
S (DK): Socket-outlets for providing power to
other equipment shall be in accordance with the
Heavy Current Regulations, Section 107-2-D1,
Standard Sheet DK 1-3a, DK 1-5a or DK 1-7a,
when used on Class I equipment. For stationary
equipment the socket-outlet shall be in accordance with Standard Sheet DK 1-1b or DK 1-5a.
1.7.5
A (DK, Heavy Current Regulations):
Class III equipment.
CLASS II EQUIPMENT shall not be fitted with socketoutlets for providing power to other equipment.
N/A
1.7.12
A (DE, Gesetz über technische Arbeitsmittel
Not such equipment
(Gerätesicherheitsgesetz) [Law on technical
rd
labour equipment {Equipment safety law}], of 23
rd
nd
October 1992, Article 3, 3 paragraph, 2
sentence, together with the "Allgemeine
Verwaltungsvorschrift zur Durchführung des
Zweiten Abschnitts des Gerätesicherheitsgesetzes" [General administrative regulation on
the execution of the Second Section of the
th
Equipment safety law], of 10 January 1996,
th
article 2, 4 paragraph item 2):
Directions for use with rules to prevent certain
hazards for (among others) maintenance of the
technical labour equipment, also for imported
technical labour equipment shall be written in the
German language.
N/A
Class III equipment, no socketoutlet.
N/A
NOTE: Of this requirement, rules for use even only by service
personnel are not exempted.
1.7.15
A (CH, Ordinance on environmentally hazardous
substances SR 814.013):
Annex 4.10 of SR 814.013 applies for batteries.
Battery Pack in compliance with
requirements of IEC 60950-1.
Overall compliance needs to be
evaluated during the national
approval process.
A (DE, Regulation on protection against hazards This national difference was
th
by X-ray, of 8 January 1987, Article 5 [Operation deleted by A11 of EN60950-1.
of X-ray emission source], clauses 1 to 4):
a) A licence is required by those who operate an
TRF No.:IECEN60950_1B
N/A
N/A
TRF originator: SGS Fimko
Page 46 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
X-ray emission source.
b) A licence in accordance with Cl. 1 is not
required by those who operate an X-ray emission
source on which the electron acceleration voltage
does not exceed 20 kV if
1) the local dose rate at a distance of 0,1 m from
the surface does not exceed 1 µSv/h and
2) it is adequately indicated on the X-ray emission
source that
i) X-rays are generated and
ii) the electron acceleration voltage must not
exceed the maximum value stipulated by
the manufacturer or importer.
c) A licence in accordance with Cl. 1 is also not
required by persons who operate an X-ray
emission source on which the electron
acceleration voltage exceeds 20 kV if
1) the X-ray emission source has been granted a
type approval and
2) it is adequately indicated on the X-ray emission
source that
i) X-rays are generated
ii) the device stipulated by the manufacturer or
importer guarantees that the maximum
permissible local dose rate in accordance
with the type approval is not exceeded and
iii) the electron acceleration voltage must not
exceed the maximum value stipulated by the
manufacturer or importer.
d) Furthermore, a licence in accordance with
Cl. 1 is also not required by persons who operate
X-ray emission sources on which the electron
acceleration voltage does not exceed 30 kV if
1) the X-rays are generated only by intrinsically
safe CRTs complying with Enclosure III, No. 6,
2) the values stipulated in accordance with
Enclosure III, No. 6.2 are limited by technical
measures and specified in the device and
3) it is adequately indicated on the X-ray emission
source that the X-rays generated are adequately screened by the intrinsically safe CRT.
2.2.4
S (NO): Requirements according to this annex,
1.7.2 and 6.1.2.1 apply.
See IEC 60950-1 report. (for all
models except for MS-163Axx)
P
Not applied for. (for model: MS163Axx only)
2.3.2
S (NO): Requirements according to this annex,
6.1.2.1 apply.
See IEC 60950-1 report. (for all
models except for MS-163Axx)
P
Not applied for. (for model: MS163Axx only)
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 47 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
2.3.3 and
2.3.4
S (NO): Requirements according to this annex,
1.7.2 and 6.1.2.1 apply.
See IEC 60950-1 report. (for all
models except for MS-163Axx)
Verdict
P
Not applied for. (for model: MS163Axx only)
2.6.3.3
S (GB): The current rating of the circuit shall be
taken as 13 A, not 16 A.
Class III equipment.
N/A
2.7.1
C: Replace the subclause as follows:
Replaced.
N/A
Basic requirements
To protect against excessive current, shortcircuits and earth faults in PRIMARY CIRCUITS,
protective devices shall be included either as
integral parts of the equipment or as parts of the
building installation, subject to the following, a), b)
and c):
a) except as detailed in b) and c), protective
devices necessary to comply with the
requirements of 5.3 shall be included as parts of
the equipment;
b) for components in series with the mains input
to the equipment such as the supply cord,
appliance coupler, r.f.i. filter and switch, shortcircuit and earth fault protection may be provided
by protective devices in the building installation;
c) it is permitted for PLUGGABLE EQUIPMENT TYPE B
or PERMANENTLY CONNECTED EQUIPMENT, to rely
on dedicated overcurrent and short-circuit
protection in the building installation, provided
that the means of protection, e.g. fuses or circuit
breakers, is fully specified in the installation
instructions.
If reliance is placed on protection in the building
installation, the installation instructions shall so
state, except that for PLUGGABLE EQUIPMENT TYPE
A the building installation shall be regarded as
providing protection in accordance with the rating
of the wall socket outlet.
S (GB): To protect against excessive currents
Not direct plug-in equipment.
and short-circuits in the PRIMARY CIRCUIT OF
DIRECT PLUG-IN EQUIPMENT, protective device shall
be included as integral parts of the DIRECT PLUGIN EQUIPMENT.
N/A
2.7.2
C: Void.
Void.
N/A
2.10.2
C: Replace in the first line "(see also 1.4.7)" by
"(see also 1.4.8)".
Replaced.
N/A
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 48 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
2.10.3.1
S (NO): Due to the IT power distribution system
used (see annex V, Fig. V.7), the A.C. MAINS
SUPPLY voltage is considered to be equal to the
line-to-line voltage and will remain at 230 V in
case of a single earth fault
No direct connection to the AC
mains supply (for all models
except for MS-163Axx)
S (CH): Supply cords of equipment having a
not exceeding 10 A shall be
provided with a plug complying with SEV 1011 or
IEC 60884-1 and one of the following dimension
sheets:
No power supply cord provided.
N/A
No power supply cord provided.
N/A
3.2.1.1
Verdict
N/A
Not applied for. (for model: MS163Axx only)
RATED CURRENT
SEV 6532-2.1991, Plug type 15, 3P+N+PE 250/400 V, 10 A
SEV 6533-2.1991, Plug type 11, L+N
250 V, 10 A
SEV 6534-2.1991, Plug type 12, L+N+PE 250 V, 10 A
In general, EN 60309 applies for plugs for
currents exceeding 10 A. However, a 16 A plug
and socket-outlet system is being introduced in
Switzerland, the plugs of which are according to
the following dimension sheets, published in
February 1998:
SEV 5932-2.1998, Plug type 25, 3L+N+PE 230/400 V, 16 A
SEV 5933-2.1998, Plug type 21, L+N
250 V, 16 A
SEV 5934-2.1998, Plug type 23, L+N+PE 250 V, 16 A
S (DK): Supply cords of single-phase equipment
having a rated current not exceeding 13 A shall
be provided with a plug according to the Heavy
Current Regulations, Section 107-2-D1.
CLASS I EQUIPMENT provided with socket-outlets
with earth contacts or which are intended to be
used in locations where protection against
indirect contact is required according to the wiring
rules shall be provided with a plug in accordance
with standard sheet DK 2-1a or DK 2-5a.
If ply-phase equipment and single-phase
equipment having a RATED CURRENT exceeding
13 A is provided with a supply cord with a plug,
this plug shall be in accordance with the Heavy
Current Regulations, Section 107-2-D1 or
EN 60309-2.
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 49 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
S (ES): Supply cords of single-phase equipment
having a rated current not exceeding 10 A shall
be provided with a plug according to
UNE 20315:1994.
No power supply cord provided.
N/A
No power supply cord provided.
N/A
S (IE): Apparatus which is fitted with a flexible
cable or cord and is designed to be connected to
a mains socket conforming to I.S. 411 by means
of that flexible cable or cord and plug, shall be
fitted with a 13 A plug in accordance with
Statutory Instrument 525:1997 – National
Standards Authority of Ireland (section 28) (13 A
Plugs and Conversion Adaptors for Domestic
Use) Regulations 1997.
No power supply cord provided.
N/A
C: Delete Note 1 and in Table 3A, delete the
conduit sizes in parentheses.
Deleted.
N/A
Supply cords of single-phase equipment having a
rated current not exceeding 2,5 A shall be
provided with a plug according to
UNE-EN 50075:1993.
CLASS I EQUIPMENT provided with socket-outlets
with earth contacts or which are intended to be
used in locations where protection against
indirect contact is required according to the wiring
rules, shall be provided with a plug in accordance
with standard UNE 20315:1994.
If poly-phase equipment is provided with a supply
cord with a plug, this plug shall be in accordance
with UNE-EN 60309-2.
S (GB): Apparatus which is fitted with a flexible
cable or cord and is designed to be connected to
a mains socket conforming to BS 1363 by means
of that flexible cable or cord and plug, shall be
fitted with a 'standard plug' in accordance with
Statutory Instrument 1768:1994 – The Plugs and
Socket etc. (Safety) Regulations 1994, unless
exempted by those regulations.
NOTE – 'Standard plug' is defined in SI 1768:1994 and
essentially means an approved plug conforming to BS 1363
or an approved conversion plug.
3.2.3
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 50 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Verdict
3.2.5.1
C: Replace
Replaced.
N/A
"60245 IEC 53" by "H05 RR-F";
"60227 IEC 52" by "H03 VV-F or H03 VVH2-F";
"60227 IEC 53" by "H05 VV-F or H05 VVH2-F2".
In Table 3B, replace the first four lines by the
following:
Up to and including 6
2)
Over 6 up to and including 10 (0,75)
3)
Over 10 up to and including 16 (1,0)
1)
0,75
1,0
1,5
In the Conditions applicable to Table 3B delete
1)
the words "in some countries" in condition .
In Note 1, applicable to Table 3B, delete the
second sentence.
3.2.5.1
S (GB): A power supply cord with conductor of
2
1,25 mm is allowed for equipment with a rated
current over 10 A and up to and including 13 A.
No power cord provided.
N/A
3.3.4
C: In table 3D, delete the fourth line: conductor
sizes for 10 to 13 A, and replace with the
following:
Deleted.
N/A
"Over 10 up to and including 16
1,5 to 2,5
1,5 to 4"
Delete the fifth line: conductor sizes for 13 to
16 A.
3.3.4
S (GB): The range of conductor sizes of flexible
cords to be accepted by terminals for equipment
with a RATED CURRENT of over 10 A up to and
including 13 A is:
2
2
- 1,25 mm to 1,5 mm nominal cross-sectional
area.
No power supply cord provided.
N/A
4.3.6
S (GB): The torque test is performed using a
socket outlet complying with BS 1363 and the
plug part of DIRECT PLUG-IN EQUIPMENT shall be
assessed to BS 1363: Part 1, 12.1, 12.2, 12.3,
12.9, 12.11, 12.12, 12.16 and 12.17, except that
the test of 12.17 is performed at not less than
125 °C.
Not direct plug-in equipment.
N/A
S (IE): DIRECT PLUG-IN EQUIPMENT is known as
Not direct plug-in equipment.
plug similar devices. Such devices shall comply
with Statutory Instrument 526:1997 – National
Standards Authority of Ireland (Section 28)
(Electrical plugs, plug similar devices and sockets
for domestic use) Regulations, 1997.
N/A
C: Add the following note:
N/A
4.3.13.6
Added.
NOTE Attention is drawn to 1999/519/EC: Council
Recommendation on the limitation of exposure of the general
public to electromagnetic fields 0 Hz to 300 GHz. Standards
taking into account this recommendation are currently under
development.
6.1.2.1
S (FI, NO, SE): Add the following text between
the first and second paragraph:
TRF No.:IECEN60950_1B
Considered(for all models
except for MS-163Axx)
P
TRF originator: SGS Fimko
Page 51 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
If this insulation is solid, including insulation
forming part of a component, it shall at least
consist of either
Not applied for. (for model: MS163Axx only)
Verdict
- two layers of thin sheet material, each of which
shall pass the electric strength test below, or
- one layer having a distance through insulation of
at least 0,4 mm, which shall pass the electric
strength test below.
If this insulation forms part of a semiconductor
component (e.g. an optocoupler), there is no
distance through insulation requirement for the
insulation consisting of an insulating compound
completely filling the casing, so that CLEARANCES
AND CREEPAGE DISTANCES do not exist, if the
component passes the electric strength test in
accordance with the compliance clause below
and in addition
- passes the tests and inspection criteria of 2.10.8
with an electric strength test of 1,5 kV multiplied
by 1,6 (the electric strength test of 2.10.7 shall be
performed using 1,5 kV), and
- is subject to ROUTINGE TESTING for electric
strength during manufacturing, using a test
voltage of 1,5 kV.
It is permitted to bridge this insulation with a
capacitor complying with EN 132400:1994,
subclass Y2.
A capacitor classified Y3 according to
EN 132400:1994, may bridge this insulation
under the following conditions:
- the insulation requirements are satisfied by
having a capacitor classified Y3 as defined by
EN 132400, which in addition to the Y3 testing, is
tested with an impulse test of 2,5 kV defined in
EN 60950:2000, 6.2.2.1;
- the additional testing shall be performed on all
the test specimens as described in EN 132400;
- the impulse test of 2,5 kV is to be performed
before the endurance test in EN 132400, in the
sequence of tests as described in EN 132400.
6.1.2.2
S (FI, NO, SE): The exclusions are applicable for
PERMANENTLY CONNECTED EQUIPMENT and
PLUGGABLE EQUIPMENT TYPE B and equipment
intended to be used in a RESTRICTED ACCESS
LOCATION where equipotential bonding has been
Not such equipment (for all
models except for MS-163Axx)
N/A
Not applied for. (for model: MS163Axx only)
applied, e.g. in a telecommunication centre, and
which has provision for a permanently connected
PROTECTIVE EARTHING CONDUCTOR and is provided
with instructions for the installation of that
conductor by a service person.
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 52 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
7.1
S (FI, NO, SE): Requirements according to this
Not connected to cable
annex, 6.1.2.1 and 6.1.2.2 apply with the term
distribution system (for all
TELECOMMUNICATION NETWORK in 6.1.2 being
models except for MS-163Axx)
replaced by the term CABLE DISTRIBUTION SYSTEM.
Not applied for. (for model: MS163Axx only)
N/A
G.2.1
S (NO): Due to the IT power distribution system
used (see annex V, Fig. V.7), the A.C. MAINS
SUPPLY voltage is considered to be equal to the
line-to-line voltage, and will remain at 230 V in
case of a single earth fault.
Not such equipment (for all
models except for MS-163Axx)
N/A
C: Replace the last paragraph of this annex by:
No CRT.
N/A
Replaced.
P
Annex H
Result – Remark
Verdict
Not applied for. (for model: MS163Axx only)
At any point 10 cm from the surface of the
operator access area, the dose rate shall not
exceed 1 µSv/h (0,1 mR/h) (see note). Account is
taken of the background level.
Replace the notes as follows:
NOTE These values appear in Directive 96/29/Euratom.
Delete Note 2.
Annex P
C: Replace the text of this annex by:
See annex ZA.
Annex Q
C: Replace the title of IEC 61032 by "Protection of persons and equipment by
enclosures – Probes for verification".
P
Add the following notes for the standards indicated:
IEC 60127
NOTE Harmonized as EN 60127 (Series) (not modified)
IEC 60269-2-1 NOTE Harmonized as HD 630.2.1 S4:2000 (modified)
IEC 60529
NOTE Harmonized as EN 60529:1991 (not modified)
IEC 61032
NOTE Harmonized as EN 61032:1998 (not modified)
IEC 61140
NOTE Harmonized as EN 61140:2001 (not modified)
ITU-T Recommendation K.31
NOTE in Europe, the suggested document is EN 50083-1.
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 53 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
Result – Remark
Annex ZA
C: NORMATIVE REFERENCES TO INTERNATIONAL PUBLICATIONS WITH
THEIR RELEVANT EUROPEAN PUBLICATIONS
Verdict
P
This European Standard incorporates, by dated or undated reference, provisions
from other publications. These normative references are cited at the appropriate
places in the text and the publications are listed hereafter. For dated references,
subsequent amendments to or revisions of any of these publications apply to this
European Standard only when incorporated in it by amendment or revision. For
undated references, the latest edition of the publication referred to applies
(including amendments).
NOTE When an international publication has been modified by common modifications, indicated by
(mod), the relevant EN/HD applies.


EN 60065:1998 + corr. June 1999
EN 60073:1996
HD 566 S1:1990
HD 214 S2:1980
HD 611.4.1.S1:1992
1)
HD 21 Series
2)
HD 22 Series
EN 60309 Series
EN 60317-43:1997
EN 60320 Series
HD 384.3 S2:1995
HD 384.4.41 S2:1996
4)
EN 132400:1994
+ A2:1998 + A3:1998 + A4:2001
EN 60417-1
HD 625.1 S1:1996 + corr. Nov. 1996
EN 60695-2-2:1994
EN 60695-2-11:2001




EN 60695-11-10:1999
EN 60695-11-20:1999
EN 60730-1:2000
EN 60825-1:1994 + corr. Febr. 1995 +
A11:1996 + corr. July 1997
EN 60825-2:2000

EN 60851-3:1996
EN 60851-5:1996
EN 60851-6:1996

EN 60990:1999

EN 61965:2001
EN ISO 178:1996
EN ISO 179 Series
EN ISO 180:2000


TRF No.:IECEN60950_1B
IEC 60050-151
IEC 60050-195
IEC 60065 (mod):1998
IEC 60073:1996
IEC 60085:1984
IEC 60112:1979
IEC 60216-4-1:1990
IEC 60227 (mod) Series
IEC 60245 (mod) Series
IEC 60309 Series
IEC 60317-43:1997
IEC 60320 (mod) Series
IEC 60364-3 (mod):1993
3)
IEC 60364-4-41 (mod):1992
IEC 60384-14:1993
IEC 60417-1
IEC 60664-1 (mod):1992
IEC 60695-2-2:1991
IEC 60695-2-11:2000
IEC 60695-2-20:1995
IEC 60695-10-2:1995
IEC 60695-11-3:2000
IEC 60695-11-4:2000
IEC 60695-11-10:1999
IEC 60695-11-20:1999
IEC 60730-1:1999 (mod)
IEC 60825-1:1993
IEC 60825-2:2000
IEC 60825-9:1999
IEC 60851-3:1996
IEC 60825-5:1996
IEC 60851-6:1996
IEC 60885-1:1987
IEC 60990:1999
IEC 61058-1:2000
IEC 61965:2000
ISO 178:1993
ISO 179 Series
ISO 180:1993
ISO 261:1998
ISO 262:1998
TRF originator: SGS Fimko
Page 54 of 109
Report No.:
11015280 001
IEC 60950-1 / EN 60950-1
Clause
Requirement – Test
EN ISO 527 Series

EN ISO 4892 Series

EN ISO 8256:1996

EN ISO 9773:1998


Result – Remark
Verdict
ISO 527 Series
ISO 386:1984
ISO 4892 Series
ISO 7000:1989
ISO 8256:1990
ISO 9772:1994
ISO 9773:1998
ITU-T:1988 Recommendation K.17
ITU-T:2000 Recommendation K.21
1) The HD 21 series is related to, but not directly equivalent with the IEC 60227 series
2) The HD 22 series is related to, but not directly equivalent with the IEC 60245 series
3) IEC 60364-4-41:1992 is superseded by IEC 60364-4-41:2001
4) EN 132400, Sectional Specification: Fixed capacitors for electromagnetic interference suppression
and connection to the supply mains (Assessment level D), and its amendments are related to, but not
directly equivalent to IEC 60384-14
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 55 of 109
1.5.1
Report No.:
11015280 001
TABLE: list of critical components
Object/part no.
Manufacturer/
trademark
Type/model
Technical data
C7230
Min. V-1, 60°C,
UL 94
1.0mm thickness
UL
Sabic
C7230P
Min. V-0, 85°C,
UL 94
1.2mm thickness
UL
Li Shin
LSE0202D1990
I/P: 100-240Vac,
50/60Hz, 1.5A
O/P: 19Vdc,
4.74A, Class II,
40°C
IEC 60950-1: TÜV, UL, CB
2001, EN
60950-1: 2001
Li Shin
LSE0202C1990
I/P: 100-240Vac,
50-60Hz, 1.5A
O/P: 19Vdc,
4.74A, Class I,
40°C
IEC 60950-1:
2001, EN
60950-1:
2001
LITEON
PA-1900-04
I/P: 100IEC 60950-1: TÜV, UL, CB
240Vac,50-60Hz, 2001, EN
1.5A O/P: 19Vdc, 60950-1: 2001
4.74A, Class I,
40°C
EPS
F10903-A
I/P: 1.2A, 100IEC 60950-1: TÜV, UL, CB
240Vac, 502001, EN
(by TÜV /SÜD)
60Hz, O/P:
60950-1: 2001
19Vdc, 4.75A, Cl.
I, 40°C
EDAC
EA10953
I/P: 2.5A, 100IEC 60950-1: TÜV, UL, CB
240Vac, 502001, EN
(by ITS)
60Hz, O/P: 1860950-1: 2001
24Vdc, 4.75A, Cl.
I, 40°C
FSP
FSP0901ADC21XX (X
can be 0-9, A-Z
or blank for
marketing
purpose)
IEC 60950I/P: 1.6A, 100TÜV, UL, CB
240Vac, 501:2001, EN
(by NEMKO)
60950-1: 2001
60Hz, O/P:
19Vdc, 4.74A, Cl.
II, 25°C
Li Shin
0335A1965
I/P: 100-240Vac,
50-60Hz, 1.7A
O/P: 19Vdc,
3.42A, Class I,
40°C
Lite-On
(Gateway)
PA-1650-02XX
(X=0-9, A-Z or
blank for
marketing
purpose only)
I/P: 100-240Vac, IEC 60950-1: TÜV, UL, CB
50-60Hz, 1.6A
2001, EN
O/P: 19Vdc,
60950-1: 2001
3.42A, Class I,
35°C
FSP
FSP065-AAC
I/P: 100-240Vac, IEC 60950-1:
Plastic Enclosure Sabic
Power Adapter
(for all models
except for MS163Axx)
(for models with
3.42A input
current rating)
P
TRF No.:IECEN60950_1B
Standard
Mark(s) of
1.
conformity
TÜV, UL, CB
IEC 60950-1: TÜV, UL, CB
2001, EN
60950-1: 2001
TÜV, UL, CB
TRF originator: SGS Fimko
Page 56 of 109
Delta
Electronics
Inc.
ADP-65HB BB or
ADP-65HB B
Report No.:
11015280 001
50-60Hz, 1.5A
O/P: 19Vdc,
3.42A, Class II,
40°C
2001, EN
60950-1: 2001
I/P: 100-240Vac,
50-60Hz, 1.5A;
O/P: 19Vdc,
3.42A, 40°C,
Class I
IEC 60950-1:
2001, EN
60950-1:
2001+A11
TÜV
(for models with
3.42A or 4.74A
input current
rating)
Delta
ADP-90SB BB
Electronics Inc.
I/P: 100-240Vac,
50-60Hz, 1.5A;
O/P: 19Vdc,
4.74A, 40°C,
Class I
IEC 60950-1:
2001, EN
60950-1:
2001+A11
TÜV, CB
Only for model
MS-163Axx
Delta
Electronics
Inc.
ADP-120ZB BB
I/P: 100-240Vac,
50-60Hz, 2.0A;
O/P: 19Vdc,
6.32A, 40°C,
Class I
IEC 60950-1:
2001, EN
60950-1:
2001+A11
TÜV, CB
Only for model
MS-163Axx
Lite-On
Technology
Corporation
PA-1121-04
I/P: 100-240Vac,
50-60Hz, 2.0A;
O/P: 19Vdc,
6.3A, 40°C,
Class I
IEC 60950-1:
2001, EN
60950-1:
2001+A11
TÜV, CB (by
Nemko)
LCD panel
LG
LP154W01
15.4”, TFT type
--
--
LG
LP154WX4-TLC1 15.4” TFT type.
--
--
LG
LP154WX4-TLC3 15.4” TFT type.
--
--
LG
LP154WE2
15.4” TFT type.
--
--
Samsung
LTN154X3-L01
15.4”, TFT type
--
--
Samsung
LTN154X3-L01-G 15.4”, TFT type
--
--
Samsung
LTN154X3-L01-K 15.4”, TFT type
--
--
Samsung
LTN154X3-L01-H 15.4”, TFT type
--
--
Samsung
LTN154P1-L02
15.4”, TFT type
--
--
Samsung
LTN154X7-L03
15.4”, TFT type
--
--
Samsung
LTN154AT01-001 15.4”, TFT type
--
--
Samsung
LTN154AT01-A03 15.4”, TFT type
--
--
Sharp
LQ154K1LBxx
15.4“, TFT type
--
--
AUO
B154EW01 V1
15.4” TFT type.
--
--
AUO
B154EW01 V7
15.4“, TFT type
--
--
AUO
B154EW01 V9
15.4“, TFT type
--
--
AUO
B154EW02
15.4“, TFT type
--
--
AUO
B154EW02 V1
15.4”, TFT type
--
--
AUO
B154EW08 V1
15.4“, TFT type
--
--
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 57 of 109
Hard Disk Drive
(HDD) (optional)
Report No.:
11015280 001
Quanta
QD15AL0201
15.4“, TFT type
--
--
Quanta
QD15TL0206
15.4“, TFT type
--
--
Chi Mei
N154I2-L02
15.4” TFT type
--
--
Chi Mei
N154I2-L05
15.4” TFT type.
--
--
Chi Mei
N154I3-L03
15.4” TFT type.
--
--
CMO
N154I1-L0B
15.4“, TFT type
--
--
CPT
CLAA154WA05
15.4“, TFT type
--
--
QDI
QD15TL02
15.4“, TFT type
--
--
Seagate or
equivalent
ST9 (will be
5Vdc, 1.2A max.
followed by
suffixes indicated
storage capacity)
or equivalent
IEC/EN
TÜV, UL
60950-1:2001
Fujitsu Ltd. or
equivalent
MHV2xxxAz (x=
0-9, z=A, H, J, K
or S) or
equivalent
IEC/EN
TÜV, UL
60950-1: 2001
Fujitsu Ltd. or
equivalent
MHW2xxxBy
5Vdc, 0.6A.
(x=0-9, y=A, H, J,
K or S) or
equivalent
IEC/EN
TÜV
60950-1:2001
Fujitsu Ltd. or
equivalent
MHY2xxxBy (x=
5Vdc, 0.6A.
0-9, y = A, H or S)
or equivalent
IEC/EN
TÜV
60950-1:2001
Fujitsu Ltd. or
equivalent
MHZ2xxxBy (x=
5Vdc, 1.5A max.
0-9, A-Z or blank,
y = A, H or S) or
equivalent
IEC/EN
60950-1:
2001+A11
Hitachi Global
Storage
Technologies
Japan, Ltd. or
equivalent
HTS5410nnxG
9SA00 (n= 0-9,
x=0-9 or A-Z)
or equivalent
IEC/EN
TÜV, UL
60950-1:2001
Hitachi Global
Storage
Technologies
Japan, Ltd.
HTS7210nnG9SA 5Vdc, 1.1A
00 (n=0-9)
IEC/EN
TÜV
60950-1:2001
Hitachi Global
Storage
Technologies
Japan, Ltd. or
equivalent
HTS5425nnK9A3 5Vdc, 700mA.
n n (n = 0-9) or
equivalent
IEC/EN
TÜV
60950-1:2001
Hitachi Global
Storage
Technologies
Japan, Ltd. or
equivalent
HTS5416nnJ9SA 5Vdc, 700mA.
n n (n = 0-9) or
equivalent
IEC/EN
TÜV
60950-1:2001
TRF No.:IECEN60950_1B
5Vdc, 0.6A max.
5Vdc, 1A max.
TÜV, UL
TRF originator: SGS Fimko
Page 58 of 109
Report No.:
11015280 001
Toshiba Corp.
or equivalent
HDD2yyyx (x=AZ, y=0-9 or A-Z)
or equivalent
5Vdc, 1.1A max.
or 5/3.3Vdc,
0.7/0.5A max.
IEC/EN 60950- TÜV
1:2001
Western
Digital
Technologie,
Inc. or
equivalent
WD800BEVS
or equivalent
5/12Vdc,
1.0/0.95A max.
IEC/EN
TÜV
60950-1:2001
DVD RW/CD-RW Hitachi-LG Data GCC-4244N or
ROM (optional)
Storage or
equivalent
equivalent
5Vdc, 2.8A max.
Class 1 laser
product, Front
bezel rated V-1,
1.0mm min.
thickness.
IEC 60950-1:
2001, IEC
60825-1:
1993+A1+A2
Philips Optical
Storage or
equivalent
SCB5265 or
equivalent
5Vdc, 1.5A max.
Class 1 laser
product, Front
bezel rated V-1,
1.0mm min.
thickness.
IEC/EN 6050- TÜV, UL
1: 2001+A11,
IEC/EN
608251:1994+A1+A
2
Philips Optical
Storage or
equivalent
SDVD8821
or
equivalent
5Vdc, 1.5A max.
Class 1 laser
product, Front
bezel rated V-1,
1.0mm min.
thickness.
IEC/EN 6050- TÜV, UL
1: 2001+A11,
IEC/EN
60825-1:
1994+A1+A2
Sony NEC
Optiarc Inc. or
equivalent
AD-7530B
or
equivalent
5Vdc, 1.5A.
Class1 Laser
product, Front
bezel rated V-1,
1.0mm min.
thickness.
IEC/EN
TÜV, CB
60950-1
:2001, IEC/EN
608251+A1+A2
Sony NEC
Optiarc Inc. or
equivalent
AD-7560S
or
equivalent
5Vdc, 1.9A.
Class1 Laser
product, Front
bezel rated V-1,
1.0mm min.
thickness.
IEC/EN
TÜV, UL
60950-1
:2001, IEC/EN
608251+A1+A2
Sony NEC
Optiarc Inc. or
equivalent
AD-7580S or
equivalent
5Vdc, 1.9A.
Class1 Laser
product, Front
bezel rated V-1,
1.0mm min.
thickness.
IEC/EN
TÜV, UL
60950-1
:2001, IEC/EN
608251+A1+A2
Sony NEC
Optiarc Inc. or
equivalent
CRX880A or
equivalent
5Vdc, 1.5A.
Class1 Laser
product, Front
bezel rated V-1,
1.0 mm min.
thickness.
IEC/EN
TÜV
60950-1:
2001, IEC/EN
608251+A1+A2
Sony NEC
CRX880A or
5Vdc, 1.5A.
IEC/EN
TRF No.:IECEN60950_1B
TÜV, UL
TÜV
TRF originator: SGS Fimko
Page 59 of 109
Report No.:
11015280 001
Optiarc Inc.or
equivalent
equivalent
Class1 Laser
product, Front
bezel rated V-1,
1.0 mm min.
thickness.
60950-1:
2001, IEC/EN
608251+A1+A2
Sony NEC
Optiarc Inc. or
equivalent
BC-5500S or
equivalent
5Vdc, 2.0A.
Class1 Laser
product, Front
bezel rated V-1,
1.0 mm min.
thickness.
IEC/EN
60950-1:
2001, IEC/EN
608251+A1+A2
Toshiba
Samsung
Storage
Technology
Corporation
TS-L802# (# = A- 5Vdc, 1.9A max.
Z or blank)
Class1 Laser
product, Front
bezel rated V-1,
1.0mm min.
thickness.
IEC/EN
TÜV
60950-1
:2001, IEC/EN
608251+A1+A2
Toshiba
Samsung
Storage
Technology
Corporation
TS-L633A
5Vdc, 1.9A max.
Class1 Laser
product, Front
bezel rated V-1,
1.0mm min.
thickness.
IEC/EN
TÜV, UL
60950-1
:2001, IEC/EN
608251+A1+A2
Hitachi-LG Data GSA-T20N or
Storage or
equivalent
equivalent
5Vdc, 1.5A.
Class1 laser
product, Front
bezel rated V-1,
1.0mm min.
thickness.
IEC/EN
TÜV
60950-1:
2001, IEC/EN
608251+A1+A2
Hitachi-LG
Data Storage
or equivalent
GCC-T10N
or equivalent
5Vdc, 1.8A.
Class1 laser
product, Front
bezel rated V1, 1.0mm min.
thickness.
IEC/EN
TÜV
60950-1:
2001, IEC/EN
608251+A1+A2
Hitachi-LG
Data Storage
or equivalent
GT10N or
equivalent
5Vdc, 1.9A.
Class1 laser
product, Front
bezel rated V1, 1.0mm min.
thickness.
IEC/EN
TÜV, UL
60950-1:
2001, IEC/EN
608251+A1+A2
Toshiba or
equivalent
SD-L912A or
equivalent
5Vdc, 1.9A max.
Laser Class I,
Front bezel rated
V-1, 1.0mm min.
thickness.
IEC/EN
60950-1:
2001,
EN608251:1994
5Vdc, 1.8A.
Class1 Laser
product, Front
bezel rated V-1,
1.0mm min.
thickness.
IEC/EN
TÜV
60950-1:
2001, IEC/EN
608251+A1+A2
Hitachi-LG Data GCC-T20N or
Storage or
equivalent
equivalent
TRF No.:IECEN60950_1B
TÜV
TUV, CB by
TUV
TRF originator: SGS Fimko
Page 60 of 109
Report No.:
11015280 001
Hitachi-LG Data GSA-T50N or
Storage or
equivalent
equivalent
5Vdc, 1.5A.
Class1 Laser
product, Front
bezel rated V-1,
1.0mm min.
thickness.
IEC/EN
TÜV
60950-1:
2001, IEC/EN
608251+A1+A2
Philips & LiteOn Digital
Solutions
Corporation or
equivalent
5Vdc, 1.5A.
Class1 Laser
product, Front
bezel rated V-1,
1.0mm min.
thickness.
IEC/EN
TÜV
60950-1:
2001, IEC/EN
608251+A1+A2
DS-8A2S or
equivalent
DC/AC inverter
Taiwan Sumida TWS-400-9589
I/P: 14.4Vdc
max., 378mA
max. O/P:
1400Vrms min.,
6.4mA max.
--
--
- Transformer in
DC/AC inverter
(T1)
Taiwan Sumida CL-14080TAZ
105°C
--
--
DC/AC inverter
Sampo
Corporation
YIVNMS0018D11 I/P: 14.4Vdc max. -740mA max. O/P:
1600Vrms min.,
6.0mA max.
--
-Transformer
(PT1)
--
--
105°C
--
--
- PCB
--
--
Min. V-1, min.
105°C
--
--
DC/AC inverter
Sampo Corp.
YIVNMS0018D11 I/P: 20Vdc,
--740mA max. O/P:
850Vrms, 6.5mA
max.
--
- Transformer
(PT1)
Yao Sheng
Electronic Co.
Ltd.
YCVT-1619ID-ZA
105°C
--
--
Darfon
Electronics
Corp.
YCVT-1619ID-Z-F 105°C
--
--
--
--
Taiwan Thick- YCVT-1619ID-ZFilm Ind. Corp. E
105°C
- Capacitor (C13) --
--
Max. 270pF, min. -2KV
--
- PCB
--
--
Min. V-1, min.
105°C
--
--
DC/AC inverter
Sampo Corp.
YIVNMS0020D11 I/P: 20Vdc,
--740mA max. O/P:
1400Vrms,
6.5mA max.
--
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 61 of 109
- Transformer
(PT1)
Report No.:
11015280 001
Yao Sheng
Electronic Co.
Ltd.
YCVT-1619ID-ZA
105°C
--
--
Darfon
Electronics
Corp.
YCVT-1619ID-Z-F 105°C
--
--
--
--
Taiwan Thick- YCVT-1619ID-ZFilm Ind. Corp. E
105°C
- Capacitor (C13) --
--
Max. 270pF, min. -2KV
--
- PCB
--
--
Min. V-1, min.
105°C
--
--
DC/AC inverter
Taiwan Sumida IV14080/T-LF
Electronics Inc.
- Transformer
(T1)
Elytone
CL-14080TAZ-LF 105°C
--
--
- Capacitor (C24) --
--
Max. 68pF, min.
2KV
--
--
- PCB
--
--
Min. V-1, min.
105°C
--
--
DC/AC inverter
Taiwan Sumida TWS-400-9614
Electronics Inc.
I/P: 14.4Vdc,
-400mA max. O/P:
1600Vrms min.,
6.5mA max.
--
I/P: 14.4Vdc,
387mA. O/P:
1400Vrms,
6.4mA
- DC/AC Inverter Taiwan Sumida CL-14080TDZ-LF 105°C
Transformer (T1)
--
--
- Capacitor (C14) --
--
Max. 100pF, min. -2KV.
--
- PCB
--
--
Min. V-1, min.
105°C
UL
DC/AC inverter
Sampo Corp.
YIVNMS0018D11 I/P: 14.4Vdc,
--A
740mA max. O/P:
1400Vrms,
6.5mA max.
--
- DC/AC Inverter
Transformer
(PT1)
Yao Sheng
Electronic Co.
Ltd.
YCVT-1619ID-ZA
105°C.
--
--
Darfon
Electronics
Corp.
YCVT-1619ID-Z-F 105°C.
--
--
--
--
Max. 180pF, min. -2KV.
--
Taiwan Thick- YCVT-1619ID-ZFilm Ind. Corp. E
- Capacitor (C13) --
TRF No.:IECEN60950_1B
--
105°C.
UL 94
TRF originator: SGS Fimko
Page 62 of 109
11015280 001
- PCB
--
--
--
--
DC/AC inverter
Sampo Corp.
YIVNMS0020D11 I/P: 14.4Vdc,
--A
740mA max. O/P:
1400Vrms,
6.5mA max.
--
- DC/AC Inverter
Transformer
(PT1)
Yao Sheng
Electronic Co.
Ltd.
YCVT-1619ID-ZA
105°C.
--
--
Darfon
Electronics
Corp.
YCVT-1619ID-Z-F 105°C.
--
--
--
--
Taiwan Thick- YCVT-1619ID-ZFilm Ind. Corp. E
Min. V-1, min.
105°C.
Report No.:
105°C.
- Capacitor (C13) --
--
Max. 180pF, min. -2KV.
--
- PCB
--
--
Min. V-1, min.
105°C.
--
--
DC/AC inverter
Mitac
Technology
Corp.
DA-1A08-MS01 L I/P: 14.4Vdc,
0.85A max. O/P:
1400Vrms min.,
6.5mA max.
--
--
- DC/AC Inverter Yao Sheng
Transformer (T1) Electronic Co.
Ltd.
273001051551
105°C.
--
--
- Capacitor (C3)
--
--
Max. 100pF, min. -2KV.
--
- PCB
--
--
Min. V-1, min.
105°C.
UL
UL 94
DC/AC Inverter
Sampo
(For model MS163Cxx, MS1637xx, MS1636xx, MS163Gxxx, MS163Nxxx, LGE50,
E500, ED500,
MS-163Pxxxx)
YIVNMS0018D11 I/P: 20Vdc,
--B
740mA max. O/P:
850Vrms, 6.5mA
max.
--
- Transformer
(PT1)
Yao Sheng
YCVT-1619ID-ZA
105°C
--
--
Darfon
YCVT-1619D-Z-F 105°C
--
--
Taiwan Thick
YCVT-1619D-Z-E 105°C
--
--
- Capacitor (C13) --
--
Max. 150pF, min. -2KV
--
- PCB
--
Min. V-1, min.
105°C
--
--
TRF No.:IECEN60950_1B
--
TRF originator: SGS Fimko
Page 63 of 109
Report No.:
11015280 001
DC/AC inverter
Mitac
(Alternate) (For
model MS163Cxx, MS1637xx, MS1636xx, MS163Gxxx, MS163Nxxx, LGE50,
E500, ED500,
MS-163Pxxxx)
DA-1A08-MS01L-- (“-“ can be 0-9,
A- Z), DA-1A08MS02L--- (“-“ can
be 0-9, A- Z)
I/P: 20Vdc, 0.85A -max. O/P:
1400Vrms,
6.5mA max.
--
- Transformer
(T1)
Yao Sheng
Electronic Co.
Ltd.
273001051551
Min. 105°C
--
--
- Capacitor (C3)
--
--
Max. 100pF, min. -2KV
--
- PCB
--
--
Min. V-1, min.
105°C
--
--
Battery Pack
Celxpert
CBPILXX (X
can be A-Z, 0-9
or blank)
11.1Vdc,
4400mAh or
4800mAh, 45°C
IEC 60950-1:
2001 EN
60950-1:
2001+A11
TÜV, CB
Celxpert
CBPIL72
11.1 or 10.8Vdc,
7200mAh, 40°C
IEC 60950-1: TÜV, CB
2001 EN
60950-1: 2001
Celxpert
BTY-MXX
11.1Vdc,
4400mAh, 45°C
IEC/EN
TÜV/SÜD
60950-1: 2001
Celxpert
BTY- M66
11.1Vdc,
4400mAh, 45°C
IEC 60950-1: TÜV, UL
2001 EN
60950-1: 2001
MSI
BTY-M65
11.1Vdc or
10.8Vdc,
7200mAh, 45°C
IEC 60950-1: TÜV, UL
2001 EN
60950-1: 2001
MSI
BTY-M66
11.1Vdc or
10.8Vdc,
4800mAh or
4400mAh, 45°C
IEC 60950-1: TÜV, UL
2001 EN
60950-1: 2001
Simplo
SQU-524
11.1Vdc or
10.8Vdc,
4400mAh, 45°C
IEC 60950-1: TÜV, UL
2001 EN
60950-1: 2001
Simplo
SQU-528
11.1Vdc or
10.8Vdc,
4800mAh, 45°C
IEC 60950-1: TÜV, UL
2001 EN
60950-1: 2001
Simplo
SQU-529
11.1Vdc or
10.8Vdc,
7200mAh, 45°C
IEC 60950-1: TÜV, UL
2001 EN
60950-1: 2001
Simplo
SQU-706
10.8 or 11.1Vdc,
5200mAh, 45°C
IEC 60950-1:
2001 EN
60950-1:
TRF No.:IECEN60950_1B
TÜV, CB
TRF originator: SGS Fimko
Page 64 of 109
Report No.:
11015280 001
2001+A11
(For model MSSimplo
163Cxx, MS1637xx, MS1636xx, MS163Gxxx, MS163Nxxx, LGE50,
E500, ED500,
MS-163Pxxxx)
SQU-718
10.8 or 11.1Vdc,
7800mAh, 45°C
IEC 60950-1:
2001 EN
60950-1:
2001+A11
TÜV, CB
Welldone
BTY-M67
10.8Vdc,
4400mAh, 45°C,
IEC 60950-1:
2001 EN
60950-1:
2001+A11
TÜV, CB
Welldone
BTY-M67
10.8Vdc,
4800mAh, 45°C,
IEC 60950-1:
2001 EN
60950-1:
2001+A11
TÜV, CB
Welldone
BTY-M67
11.1Vdc,
5200mAh, 45°C,
IEC 60950-1:
2001 EN
60950-1:
2001+A11
TÜV, CB
STL
BTY-M66
10.8Vdc,
4800mAh, 50°C
IEC 60950-1:
2001 EN
60950-1:
2001+A11
TÜV
(For model MSSTL
163Cxx, MS1637xx, MS1636xx, MS163Gxxx, MS163Nxxx, LGE50,
E500, ED500,
MS-163Pxxxx)
BTY-M66
10.8Vdc,
5200mAh, 50°C
EN 60950-1
IEC 60950-1
TUV
(For model MSSTL
163Cxx, MS1637xx, MS1636xx, MS163Gxxx, MS163Nxxx, LGE50,
E500, ED500,
MS-163Pxxxx)
BTY-M66
10.8Vdc,
4400mAh, 50°C
EN 60950-1
IEC 60950-1
TUV
CPU Fan
Forcecon
DFB451005M10T 5Vdc, 0.33A
max., 5.1 CFM
IEC 60950-1:
2001
TÜV, UL
Tranyoung
6010H05F PF3
5Vdc, 0.55A
max., 7.08CFM
IEC 60950-1:
2001
TÜV
MFNC-C537F
5Vdc, 0.36A,
4.5CFM
IEC 60950-1:
2001
TÜV
(Only for models LG
MS-1637xx, MS1636xx, MS163Cxx, MS163Nxxx, LGE50,
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 65 of 109
Report No.:
11015280 001
E500, ED500)
IEC 60950-1:
2001
TÜV
DFB450805M10T 5Vdc, 0.4A,
5.01CFM
IEC 60950-1:
2001
TÜV
(Only for model
LG
MS-1637xx, MS163Cxx, MS163Nxxx, LGE50,
E500, ED500)
MFNC-C537D
5Vdc, 0.25A,
3.6CFM
IEC 60950-1:
2001
TÜV
LG
MFNC-C537A
5Vdc, 0.36A,
5.0CFM
IEC 60950-1:
2001
TÜV
Forcecon
DFB450805M10T 5Vdc, 0.4A,
5.01CFM
IEC 60950-1:
2001
TÜV
LG
MFNC-C537D
IEC 60950-1:
2001
TÜV
(Only for model
MS-1637xx and
MS-163Cxx)
LG
MFNC-C537A
Forcecon
5Vdc, 0.36A,
5.0CFM
5Vdc, 0.25A,
3.6CFM
(Only for model
Forcecon
MS-1637xx, MS1636xx, MS163Cxx, MS163Axx, MS163Nxxx LGE50,
E500, ED50)
DFS450805M10T 5Vdc, 0.4A max., IEC 60950-1:
3CFM.
2001 EN
60950-1:
2001+A11
TÜV, UL
(Only for model
MS-163Gxxx,
MS-163Pxxxx)
Forcecon
DFS451205M10T 5Vdc, 0.4A max., IEC 60950-1:
4.5CFM min.
2001 EN
60950-1:
2001+A11
TÜV
(Only for model
MS-1637xx, MS163Cxx, MS1636xx, MS163Axx, LGE50,
E500, ED500)
ADDA
AB0605HX-HE3
5Vdc, 0.25A
max., 4.0CFM
IEC/EN
TÜV, UL
60950-1: 2001
Modem Card
(optional) (for all
models except
MS-163Pxxxx)
Qcom
MD560(B)-01
3.3Vdc, 58mA
IEC 60950-1: TÜV, UL
2001, EN
60950-1:2001
Qcom
MD560LMI-2
3.8Vdc, 11mA
IEC 60950-1:
2001, EN
60950-1:
2001
Qcom
MD560(B)
3.3Vdc, 58mA
IEC 60950-1: TÜV, UL
2001, EN
60950-1:2001
LSI
Athens AM2
3.3Vdc.
IEC 60950-1: TÜV, UL, CB
2001, EN
60950-1:2001
TRF No.:IECEN60950_1B
TÜV, UL
TRF originator: SGS Fimko
Page 66 of 109
Report No.:
11015280 001
LSI
D40
3.3Vdc, 500mA.
IEC 60950-1: TÜV, UL
2001, EN
60950-1:2001
Motorola Inc.
ML3054
3.3Vdc.
IEC/EN
TÜV, CB, UL
60950-1:2001
Insulation Sheet
(around modem
card)
--
--
V-2 min.,
UL 94
thickness 0.4mm
min.
UL
Speakers (Two
provided)
--
--
Max. 3.5Ω, Max.
5W
--
Insulation sheet
SP Pacific
(covered the
inside of PCMCIA
slot, near PCB
side)
FR765
VTM-0, 80°C, 0.1 UL 94
mm thickness
UL
Mesh Screen
SABIC
INNOVATIVE
PLASTICS US
LLC
FR700
V-0, 125°C, 0.23
mm min.
thickness
UL 94
UL
TV-Tuner Card
(for model MS163Axx)
(Optional)
Pro-Nets
Technology
Corporation
HM100E
Rated 3.3Vdc
--
--
PCB
--
--
V-1 min. 105°C
UL 94
UL
RTC Battery
Panasonic
Corporation
(Matsushita)
CR2032
Max. abnormal
charge current
10mA.
UL 1642
UL
Sony Energy
CR2032
Max.abnormal
charge current
10mA.
UL 1642
UL
Toshiba
CR2032
Max.abnormal
charge current
10mA.
UL 1642
UL
Vic-Dawn
CR2032
Max. abnormal
charge current
10mA.
UL 1642
UL
miniSMDC150
series
1.5A, 6Vdc
IEC 60730-1
VDE, UL
Littelfuse
1812L150
1.5A, 6Vdc
IEC 60730-1
VDE, UL
Bourns
MF-MSMF150
1.5A, 6Vdc
IEC 60730-1
VDE, UL
Polytronics
SMD1812P150TF 1.5A, 6Vdc
IEC 60730-1
VDE, UL
Littelfuse
1812L150-C
IEC 60730-1
VDE, UL
Modem Card
(optional)
Polyswitch for all Raychem
USB ports (F1 for
mainboard A, B,
C, D, F, G, H and
TNV-board (a);
FC1 for TNVboard(b))
Polyswitch for all
TRF No.:IECEN60950_1B
1.5A, 8Vdc
--
TRF originator: SGS Fimko
Page 67 of 109
Report No.:
11015280 001
USB ports (F1 for
mainboard E and
FC7 for TNVboard (c) (for
model MS163Pxxxx use
only)
Dummy card of
PCMCIA
(for model MS163Pxxxx)
Sabic
C7230P
Min. V-0, 85°C,
UL 94
1.2mm thickness
UL
Note(s):
1. An asterisk indicates a mark that assures the agreed level of surveillance.
1.6.2
Fuse #
TABLE: electrical data (in normal conditions)
Irated (A)
U (Vdc)
P (W)
I (A)
P
Ifuse (A)
Condition/status
Model: MS-1039xxxxx with DC/AC inverter Taiwan Sumida, type TWS-400-9589 (Mainboard A)
--
4.74
19
78.9
4.15
--
Maximum normal load
Model: MS-1039xxxxx with DC/AC inverter: Sampo type YIVNMS0018D11 (Mainboad A)
--
3.42
19
60.0
3.16
--
Maximum normal load, test with
battery pack SQU-528
--
3.42
19
60.0
3.16
--
Maximum normal load, test with
battery pack SQU-529
--
3.42
19
60.0
3.16
--
Maximum normal load, test with
battery pack SQU-524
Model: MS-1034xxxxx with DC/AC inverter Taiwan Sumida, type TWS-400-9589 (Mainboard B)
--
3.42
19
60.4
3.18
--
Maximum normal load
Model: LGF1 with DC/AC inverter Taiwan Sumida, type TWS-400-9589 (Mainboard B)
--
4.74
19
62.7
3.33
--
Maximum normal load
63.27
3.33
--
Maximum normal load
80.18
4.22
--
Maximum normal load
Model: MS-1637xx (Mainboard C)
--
3.42
19
Model: MS-1636xx (Mainboard D)
--
4.74
19
Model: MS-163Axx with DC/AC inverter: Taiwan Sumida / TWS-400-9614 (Mainboard E)
--
6.3
19
106.1
5.58
--
Maximum normal load
Model: MS-163Gxxx with DC/AC inverter: Mitac / DA-1A08-MS01L (Mainboard F)
--
4.74
19
82.4
4.34
--
Maximum normal load
60.99
3.21
--
Maximum normal load
Model: MS-163Nxxx (Mainboard G)
--
3.42
TRF No.:IECEN60950_1B
19
TRF originator: SGS Fimko
Page 68 of 109
Report No.:
11015280 001
Model MS-163Pxxxx (Mainboard H), DC/AC Inverter: Mitac /DA-1A08-MS01L, Battery pack:
SIMPLO/SQU718 (7800mAh), CPU: Intel / Celeron 530, 1.73GHz, DC fan: Forcecon, type
DFS451205M10T (4.5CFM)
--
4.74
19Vdc
82.27
4.33
--
Maximum normal load
Note(s):
2.1.1.5
TABLE: max. V, A, VA test
Voltage (rated)
(V)
N/A
Current (rated)
(A)
Voltage (max.)
(V)
Current (max.)
(A)
VA (max.)
(VA)
Note(s):
2.1.1.7
TABLE: discharge test
Condition
N/A
τ calculated τ measured
(s)
(s)
t u→ 0V
(s)
Comments
Note(s):
2.2.2
TABLE: Hazardous voltage measurement
Transformer
N/A
Location
max. Voltage
V peak
V d.c.
Voltage Limitation
Component
Note(s):
2.2.3
TABLE: SEL voltage measurement
Location
N/A
Voltage measured (V)
Comments
Note(s):
2.4.2
TABLE: limited current circuit measurement
Location
Voltage
(V)
Current
(mA)
P
Freq.
(kHz)
Limit (mA) Comments
Test with DC/AC inverter Taiwan Sumida, type TWS-400-9589
Normal condition
CN2 pin 1 to GND
--
--
--
--
Unit shutdown
CN2 pin 2 to GND
--
--
--
--
Unit shutdown
CN2 pin 1 to CN2 pin 2
--
--
--
--
Unit shutdown
T1 pin 6 to GND
--
--
--
--
Unit shutdown
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 69 of 109
Report No.:
T1 pin 7 to GND
--
--
--
--
Unit shutdown
T1 pin 6 to pin 7
--
--
--
--
Unit shutdown
11015280 001
single fault condition (C24 short)
CN2 pin 1 to GND
--
--
--
--
Unit shutdown
CN2 pin 2 to GND
--
--
--
--
Unit shutdown
CN2 pin 1 to CN2 pin 2
--
--
--
--
Unit shutdown
T1 pin 6 to GND
--
--
--
--
Unit shutdown
T1 pin 7 to GND
--
--
--
--
Unit shutdown
T1 pin 6 to pin 7
--
--
--
--
Unit shutdown
single fault condition (C21 short)
CN2 pin 1 to GND
--
--
--
--
Unit shutdown
CN2 pin 2 to GND
--
--
--
--
Unit shutdown
CN2 pin 1 to CN2 pin 2
--
--
--
--
Unit shutdown
T1 pin 6 to GND
--
--
--
--
Unit shutdown
T1 pin 7 to GND
--
--
--
--
Unit shutdown
T1 pin 6 to pin 7
--
--
--
--
Unit shutdown
single fault condition (Q2 pin B-C short)
CN2 pin 1 to GND
--
--
--
--
Unit shutdown
CN2 pin 2 to GND
--
--
--
--
Unit shutdown
CN2 pin 1 to CN2 pin 2
--
--
--
--
Unit shutdown
T1 pin 6 to GND
--
--
--
--
Unit shutdown
T1 pin 7 to GND
--
--
--
--
Unit shutdown
T1 pin 6 to pin 7
--
--
--
--
Unit shutdown
single fault condition (U1 pin 7-8 short)
CN2 pin 1 to GND
--
--
--
--
Unit shutdown
CN2 pin 2 to GND
--
--
--
--
Unit shutdown
CN2 pin 1 to CN2 pin 2
--
--
--
--
Unit shutdown
T1 pin 6 to GND
--
--
--
--
Unit shutdown
T1 pin 7 to GND
--
--
--
--
Unit shutdown
T1 pin 6 to pin 7
--
--
--
--
Unit shutdown
single fault condition (U1 pin 17-18 short)
CN2 pin 1 to GND
--
--
--
--
Unit shutdown
CN2 pin 2 to GND
--
--
--
--
Unit shutdown
CN2 pin 1 to CN2 pin 2
--
--
--
--
Unit shutdown
T1 pin 6 to GND
--
--
--
--
Unit shutdown
T1 pin 7 to GND
--
--
--
--
Unit shutdown
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 70 of 109
T1 pin 6 to pin 7
--
--
Report No.:
--
--
Unit shutdown
11015280 001
single fault condition (C18 short)
CN2 pin 1 to GND
--
--
--
--
Unit shutdown
CN2 pin 2 to GND
--
--
--
--
Unit shutdown
CN2 pin 1 to CN2 pin 2
--
--
--
--
Unit shutdown
T1 pin 6 to GND
--
--
--
--
Unit shutdown
T1 pin 7 to GND
--
--
--
--
Unit shutdown
T1 pin 6 to pin 7
--
--
--
--
Unit shutdown
single fault condition (U1 pin 2 open)
CN2 pin 1 to GND
--
--
--
--
Unit shutdown
CN2 pin 2 to GND
--
--
--
--
Unit shutdown
CN2 pin 1 to CN2 pin 2
--
--
--
--
Unit shutdown
T1 pin 6 to GND
--
--
--
--
Unit shutdown
T1 pin 7 to GND
--
--
--
--
Unit shutdown
T1 pin 6 to pin 7
--
--
--
--
Unit shutdown
single fault condition (R23 open)
CN2 pin 1 to GND
--
--
--
--
Unit shutdown
CN2 pin 2 to GND
--
--
--
--
Unit shutdown
CN2 pin 1 to CN2 pin 2
--
--
--
--
Unit shutdown
T1 pin 6 to GND
--
--
--
--
Unit shutdown
T1 pin 7 to GND
--
--
--
--
Unit shutdown
T1 pin 6 to pin 7
--
--
--
--
Unit shutdown
Test with DC/AC inverter: Sampo type YIVNMS0018D11
normal condition
PT1 pin 6 to pin 5
--
--
--
--
Unit shutdown
PT1 pin 6 to earth
--
--
--
--
Unit shutdown
PT1 pin 5 to earth
4.4
2.2
63
44.1
CON2 pin 1 to 2
--
--
--
--
Unit shutdown
CON2 pin 1 to earth
--
--
--
--
Unit shutdown
CON2 pin 2 to earth
3.2
1.6
63
44.1
--
--
single fault condition (C13 short)
PT1 pin 6 to pin 5
--
--
--
--
Unit shutdown
PT1 pin 6 to earth
--
--
--
--
Unit shutdown
PT1 pin 5 to earth
4.4
2.2
63
44.1
CON2 pin 1 to 2
--
--
--
--
Unit shutdown
CON2 pin 1 to earth
--
--
--
--
Unit shutdown
TRF No.:IECEN60950_1B
--
TRF originator: SGS Fimko
Page 71 of 109
CON2 pin 2 to earth
3.2
1.6
63
Report No.:
44.1
11015280 001
--
single fault condition (C15 short)
PT1 pin 6 to pin 5
--
--
--
--
Unit shutdown
PT1 pin 6 to earth
--
--
--
--
Unit shutdown
PT1 pin 5 to earth
4.4
2.2
63
44.1
Unit shutdown
CON2 pin 1 to 2
--
--
--
--
Unit shutdown
CON2 pin 1 to earth
--
--
--
--
Unit shutdown
CON2 pin 2 to earth
3.2
1.6
63
44.1
Unit shutdown
single fault condition (Q2 pin 2-6 short)
PT1 pin 6 to pin 5
--
--
--
--
Unit shutdown
PT1 pin 6 to earth
--
--
--
--
Unit shutdown
PT1 pin 5 to earth
--
--
--
--
Unit shutdown
CON2 pin 1 to 2
--
--
--
--
Unit shutdown
CON2 pin 1 to earth
--
--
--
--
Unit shutdown
CON2 pin 2 to earth
--
--
--
--
Unit shutdown
Test with DC/AC inverter: Sampo type YIVNMS0018D11-Normal condition
CON2 pin 1 to pin2
--
--
--
--
Unit shutdown
CON2 pin 1 to earth
--
--
--
--
Unit shutdown
CON2 pin 2 to earth
3.44
1.72
61
42.7
PT1 pin 5 to pin 6
--
--
--
--
Unit shutdown
PT1 pin 5 to earth
--
--
--
--
Unit shutdown
PT1 pin 6 to earth
2.76
1.38
113
70
C13 shorted
CON2 pin 1 to pin2
--
--
--
--
Unit shutdown
CON2 pin 1 to earth
--
--
--
--
Unit shutdown
CON2 pin 2 to earth
3.28
1.64
61
42.7
PT1 pin 5 to pin 6
--
--
--
--
Unit shutdown
PT1 pin 5 to earth
--
--
--
--
Unit shutdown
PT1 pin 6 to earth
2.92
1.46
125
70
R8 shorted
CON2 pin 1 to pin2
--
--
--
--
Unit shutdown
CON2 pin 1 to earth
--
--
--
--
Unit shutdown
CON2 pin 2 to earth
3.44
1.72
61
42.7
PT1 pin 5 to pin 6
--
--
--
--
Unit shutdown
PT1 pin 5 to earth
--
--
--
--
Unit shutdown
PT1 pin 6 to earth
2.80
1.40
132
70
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 72 of 109
Report No.:
11015280 001
R9 shorted
CON2 pin 1 to pin2
--
--
--
--
Unit shutdown
CON2 pin 1 to earth
--
--
--
--
Unit shutdown
CON2 pin 2 to earth
--
--
--
--
Unit shutdown
PT1 pin 5 to pin 6
--
--
--
--
Unit shutdown
PT1 pin 5 to earth
--
--
--
--
Unit shutdown
PT1 pin 6 to earth
3.12
1.56
136
70
Q1 pin2-5 shorted
CON2 pin 1 to pin2
--
--
--
--
Unit shutdown
CON2 pin 1 to earth
--
--
--
--
Unit shutdown
CON2 pin 2 to earth
--
--
--
--
Unit shutdown
PT1 pin 5 to pin 6
--
--
--
--
Unit shutdown
PT1 pin 5 to earth
--
--
--
--
Unit shutdown
PT1 pin 6 to earth
4.88
2.44
107
70
Test with Sampo DC/AC inverter, type YIVNMS0020D11-Normal condition
CON2 pin 1 to pin2
--
--
--
--
Unit shutdown
CON2 pin 1 to earth
--
--
--
--
Unit shutdown
CON2 pin 2 to earth
5.28
26.4
133
70
PT1 pin 5 to pin 6
--
--
--
--
Unit shutdown
PT1 pin 5 to earth
--
--
--
--
Unit shutdown
PT1 pin 6 to earth
0.76
0.38
64
44.8
C13 shorted
CON2 pin 1 to pin2
--
--
--
--
Unit shutdown
CON2 pin 1 to earth
--
--
--
--
Unit shutdown
CON2 pin 2 to earth
5.44
2.27
140
70
PT1 pin 5 to pin 6
--
--
--
--
Unit shutdown
PT1 pin 5 to earth
--
--
--
--
Unit shutdown
PT1 pin 6 to earth
0.82
0.41
112
70
R8 shorted
CON2 pin 1 to pin2
--
--
--
--
Unit shutdown
CON2 pin 1 to earth
--
--
--
--
Unit shutdown
CON2 pin 2 to earth
5.68
2.84
422
70
PT1 pin 5 to pin 6
--
--
--
--
Unit shutdown
PT1 pin 5 to earth
--
--
--
--
Unit shutdown
PT1 pin 6 to earth
0.78
0.39
107
70
R9 shorted
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 73 of 109
Report No.:
CON2 pin 1 to pin2
--
--
--
--
Unit shutdown
CON2 pin 1 to earth
--
--
--
--
Unit shutdown
CON2 pin 2 to earth
--
--
--
--
Unit shutdown
PT1 pin 5 to pin 6
--
--
--
--
Unit shutdown
PT1 pin 5 to earth
--
--
--
--
Unit shutdown
PT1 pin 6 to earth
--
--
--
--
Unit shutdown
11015280 001
Q1 pin2-6 shorted
CON2 pin 1 to pin2
--
--
--
--
Unit shutdown
CON2 pin 1 to earth
--
--
--
--
Unit shutdown
CON2 pin 2 to earth
--
--
--
--
Unit shutdown
PT1 pin 5 to pin 6
--
--
--
--
Unit shutdown
PT1 pin 5 to earth
--
--
--
--
Unit shutdown
PT1 pin 6 to earth
--
--
--
--
Unit shutdown
Test with Sumida DC/AC inverter, type IV14080/T-LF
Normal condition
CN2 pin 1 to pin 2
--
--
--
--
Unit shutdown
CN2 pin 1 to earth
--
--
--
--
Unit shutdown
CN2 pin 2 to earth
2.40
1.20
56
39.2
T1 pin 7 to pin 8
--
--
--
--
Unit shutdown
T1 pin 7 to earth
--
--
--
--
Unit shutdown
T1 pin 8 to earth
0.92
0.46
58
40.6
C24 Shorted
CN2 pin 1 to pin 2
--
--
--
--
Unit shutdown
CN2 pin 1 to earth
--
--
--
--
Unit shutdown
CN2 pin 2 to earth
2.40
1.20
56
39.2
T1 pin 7 to pin 8
--
--
--
--
Unit shutdown
T1 pin 7 to earth
--
--
--
--
Unit shutdown
T1 pin 8 to earth
1.02
0.51
56
39.2
R20 Shorted
CN2 pin 1 to pin 2
--
--
--
--
Unit shutdown
CN2 pin 1 to earth
--
--
--
--
Unit shutdown
CN2 pin 2 to earth
--
--
--
--
Unit shutdown
T1 pin 7 to pin 8
--
--
--
--
Unit shutdown
T1 pin 7 to earth
--
--
--
--
Unit shutdown
T1 pin 8 to earth
--
--
--
--
Unit shutdown
--
Unit shutdown
C17 Shorted
CN2 pin 1 to pin 2
TRF No.:IECEN60950_1B
--
--
--
TRF originator: SGS Fimko
Page 74 of 109
Report No.:
CN2 pin 1 to earth
--
--
--
--
CN2 pin 2 to earth
2.68
1.34
58
40.6
T1 pin 7 to pin 8
--
--
--
--
Unit shutdown
T1 pin 7 to earth
--
--
--
--
Unit shutdown
T1 pin 8 to earth
1.04
0.52
114
70
11015280 001
Unit shutdown
C23 Shorted
T1 pin 7 to pin 8
--
--
--
--
Unit shutdown
T1 pin 7 to earth
--
--
--
--
Unit shutdown
T1 pin 8 to earth
--
--
--
--
Unit shutdown
Test with DC/AC inverter: Taiwan Sumida / TWS-400-9614
Normal condition
CN2 pin 1 to CN2 pin 2
20.6
10.3
56
39.2
CN2 pin 1 to GND
0
0
--
--
CN2 pin 2 to GND
3.52
1.76
55
38.5
T1 pin 5 to pin 4
0
0
--
--
Unit shutdown
T1 pin 5 to GND
0
0
--
--
Unit shutdown
T1 pin 4 to GND
2.30
1.15
54
37.8
Unit shutdown
Single fault condition (C14 short)
CN2 pin 1 to CN2 pin 2
20.4
10.2
56
39.2
CN2 pin 1 to GND
0
0
--
--
CN2 pin 2 to GND
3.44
1.72
56
39.2
T1 pin 5 to pin 4
0
0
--
--
Unit shutdown
T1 pin 5 to GND
0
0
--
--
Unit shutdown
T1 pin 4 to GND
2.48
1.24
56
39.2
Unit shutdown
Single fault condition (Q3 pin 2-6 short)
CN2 pin 1 to CN2 pin 2
19.8
9.9
56
39.2
CN2 pin 1 to GND
0
0
--
--
Unit shutdown
CN2 pin 2 to GND
0
0
--
--
Unit shutdown
T1 pin 5 to pin 4
0
0
--
--
Unit shutdown
T1 pin 5 to GND
0
0
--
--
Unit shutdown
T1 pin 4 to GND
0
0
--
--
Unit shutdown
Single fault condition (R9 short)
CN2 pin 1 to CN2 pin 2
21.0
10.5
55
38.5
CN2 pin 1 to GND
0
0
--
--
CN2 pin 2 to GND
3.52
1.76
56
39.2
0
0
--
--
T1 pin 5 to pin 4
TRF No.:IECEN60950_1B
Unit shutdown
Unit shutdown
TRF originator: SGS Fimko
Page 75 of 109
Report No.:
T1 pin 5 to GND
0
0
--
--
T1 pin 4 to GND
2.18
1.09
56
39.2
11015280 001
Unit shutdown
Single fault condition (R4 short)
CN2 pin 1 to CN2 pin 2
0
0
--
--
Unit shutdown
CN2 pin 1 to GND
0
0
--
--
Unit shutdown
T1 pin 5 to pin 4
0
0
--
--
Unit shutdown
T1 pin 5 to GND
0
0
--
--
Unit shutdown
T1 pin 4 to GND
0
0
--
--
Unit shutdown
Single fault condition (CR1 short)
CN2 pin 2 to GND
3.55
1.77
56
39.2
Test with DC/AC inverter: Mitac / DA-1A08-MS01 L
Normal condition
CN2 pin 1 to pin 2
0
0
--
--
Unit shutdown
CN2 pin 2 to GND
0
0
--
--
Unit shutdown
CN2 pin 1 to GND
0
0
--
--
Unit shutdown
T1 pin 4 to pin 3
0
0
--
--
Unit shutdown
T1 pin 3 to GND
0.6
0.3
58
40.6
T1 pin 4 to GND
0
0
--
--
Unit shutdown
Single fault condition (C3 short)
CN2 pin 1 to pin 2
0
0
--
--
Unit shutdown
CN2 pin 2 to GND
0
0
--
--
Unit shutdown
CN2 pin 1 to GND
3.2
1.6
56
39.2
T1 pin 4 to pin 3
0
0
--
--
T1 pin 3 to GND
0.6
0.3
57
39.9
T1 pin 4 to GND
0
0
--
--
Unit shutdown
Unit shutdown
Single fault condition (D2 pin 2-3 short)
CN2 pin 1 to pin 2
0
0
--
--
Unit shutdown
CN2 pin 2 to GND
0
0
--
--
Unit shutdown
CN2 pin 1 to GND
3.96
1.98
58
40.6
T1 pin 4 to pin 3
0
0
--
--
T1 pin 3 to GND
0.67
0.34
55
38.5
T1 pin 4 to GND
0
0
--
--
Unit shutdown
Unit shutdown
Single fault condition (R15 short)
CN2 pin 1 to pin 2
0
0
--
--
Unit shutdown
CN2 pin 2 to GND
0
0
--
--
Unit shutdown
CN2 pin 1 to GND
0
0
--
--
Unit shutdown
T1 pin 4 to pin 3
0
0
--
--
Unit shutdown
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 76 of 109
Report No.:
T1 pin 3 to GND
0
0
--
--
Unit shutdown
T1 pin 4 to GND
0
0
--
--
Unit shutdown
11015280 001
Single fault condition (U2 pin 4-13 short)
CN2 pin 1 to pin 2
0
0
--
--
Unit shutdown
CN2 pin 2 to GND
0
0
--
--
Unit shutdown
CN2 pin 1 to GND
0
0
--
--
Unit shutdown
T1 pin 4 to pin 3
0
0
--
--
Unit shutdown
T1 pin 3 to GND
0
0
--
--
Unit shutdown
T1 pin 4 to GND
0
0
--
--
Unit shutdown
Single fault condition (U2 pin 2-4 short)
CN2 pin 1 to pin 2
0
0
--
--
Unit shutdown
CN2 pin 2 to GND
0
0
--
--
Unit shutdown
CN2 pin 1 to GND
0
0
--
--
Unit shutdown
T1 pin 4 to pin 3
0
0
--
--
Unit shutdown
T1 pin 3 to GND
0
0
--
--
Unit shutdown
T1 pin 4 to GND
0
0
--
--
Unit shutdown
Test with Inverter Model: DA-1A08-MS01L---, DA-1A08-MS02L--Normal Condition
CN2 Pin1-2
--
--
--
--
The output shutdown
immediately
CN2 Pin1-Earth
--
--
--
--
The output shutdown
immediately
CN2 Pin2-Earth
3.4
1.7
55
38.5
T1 Pin3-4
--
--
--
--
The output shutdown
immediately
T1 Pin4-Earth
--
--
--
--
The output shutdown
immediately
T1 Pin3-Earth
0.8
0.4
55
38.5
C3Short
CN2 Pin1-2
--
--
--
--
The output shutdown
immediately
CN2 Pin1-Earth
--
--
--
--
The output shutdown
immediately
CN2 Pin2-Earth
--
--
--
--
The output shutdown
immediately
T1 Pin3-4
--
--
--
--
The output shutdown
immediately
T1 Pin4-Earth
--
--
--
--
The output shutdown
immediately
T1 Pin3-Earth
--
--
--
--
The output shutdown
immediately
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 77 of 109
Report No.:
11015280 001
U1 pin2-4 Short
CN2 Pin1-2
--
--
--
--
The output shutdown
immediately
CN2 Pin1-Earth
--
--
--
--
The output shutdown
immediately
CN2 Pin2-Earth
--
--
--
--
The output shutdown
immediately
T1 Pin3-4
--
--
--
--
The output shutdown
immediately
T1 Pin4-Earth
--
--
--
--
The output shutdown
immediately
T1 Pin3-Earth
--
--
--
--
The output shutdown
immediately
D1 pin2-3 Short
CN2 Pin1-2
--
--
--
--
The output shutdown
immediately
CN2 Pin1-Earth
--
--
--
--
The output shutdown
immediately
CN2 Pin2-Earth
--
--
--
--
The output shutdown
immediately
T1 Pin3-4
--
--
--
--
The output shutdown
immediately
T1 Pin4-Earth
--
--
--
--
The output shutdown
immediately
T1 Pin3-Earth
--
--
--
--
The output shutdown
immediately
Note(s):
1.
The DC/AC Inverter source of Sampo type YIVNMS0018D11-A is identical to model Sampo type
YIVNMS0018D11-- except for rating of C13 changed from max. 270pF to 180pF. (The measured voltage
of YIVNMS0018D11-A is 1.13kV, which is smaller than YIVNMS0018D11--), test were performed on
YIVNMS0018D11-- to represent YIVNMS0018D11-A.
2. The DC/AC Inverter source of Sampo type YIVNMS0020D11-A is identical to model Sampo type
YIVNMS0020D11-- except for rating of C13 changed from max. 270pF to 180pF. (The measured voltage
of YIVNMS0020D11-A is 1.15kV, which is smaller than YIVNMS0020D11--), test were performed on
YIVNMS0020D11-- to represent YIVNMS0020D11-A.
3. The DC/AC Inverter source of Sampo type YIVNMS0018D11-B is identical to model Sampo type
YIVNMS0018D11-- except for rating of C13 changed from max. 180pF to 150pF. (The measured voltage
of YIVNMS0020D11-A is 1.2kV, which is smaller than YIVNMS0020D11--) test were performed on
YIVNMS0018D11-- to represent YIVNMS0018D11-B.
2.5
TABLE: limited power source measurement
Limits
P
Measured
Verdict
2.7
Pass
For model MS-1039xxxxx (Mainboad A)
According to Table 2B (normal condition) – USB1, USB2 (Uoc = 5.04V)
current (in A)
TRF No.:IECEN60950_1B
8
TRF originator: SGS Fimko
apparent power (in VA)
Page 78 of 109
Report No.:
25.2
10.2
Pass
8
3.5
Pass
25.3
14.1
Pass
8
3.00
Pass
25.10
12.60
Pass
8
3.66
Pass
25.1
12.52
Pass
8
4.04
Pass
25.1
12.92
Pass
8
3.53
Pass
25.00
12.24
Pass
8
3.64
Pass
25.0
14.59
Pass
8
4.14
Pass
25.1
15.21
Pass
8
3.04
Pass
5*Uoc= 24.95
11.29
Pass
8
3.10
Pass
5*Uoc= 24.95
11.62
Pass
11015280 001
According to Table 2B (normal condition) – USBJ1, USBJ2 (Uoc = 5.05V)
current (in A)
apparent power (in VA)
For model MS-1637xx (Mainboard C)
Right side USB ports
1.
According to Table 2B (normal condition) Uoc=5.02V
current (in A)
apparent power (in VA)
Left side USB ports
According to Table 2B (normal condition) Uoc=5.02V
current (in A)
apparent power (in VA)
According to Table 2B (Q21 pin 1-8 shorted) Uoc=5.02V
current (in A)
apparent power (in VA)
For model MS-1636xx (Mainboard D)
Right side USB ports
1.
According to Table 2B (normal condition) Uoc=5.00V
current (in A)
apparent power (in VA)
Left side USB ports
According to Table 2B (normal condition) Uoc=5.00V
current (in A)
apparent power (in VA)
According to Table 2B (PQ32 pin 1-8 shorted) Uoc=5.02V
current (in A)
apparent power (in VA)
For model MS-163Axx(Mainboard E)
According to Table 2B (normal condition), USB1 port (Uoc = 4.99V)
current (in A)
apparent power (in VA)
According to Table 2B (normal condition), USB2 port (Uoc = 4.99V)
current (in A)
apparent power (in VA)
According to Table 2B (normal condition), USB3 port (Uoc = 4.99V)
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 79 of 109
current (in A)
apparent power (in VA)
Report No.:
11015280 001
8
3.35
Pass
5*Uoc= 24.95
13.16
Pass
8
3.47
Pass
5*Uoc= 24.95
13.19
Pass
8
3.03
Pass
5*Uoc= 25.05
11.31
Pass
8
3.03
Pass
5*Uoc= 25.05
11.31
Pass
8
2.91
Pass
5*Uoc= 25.05
11.12
Pass
8
2.91
Pass
5*Uoc= 25.05
11.12
Pass
8
3.5
Pass
25.4 (5 X Uoc)
13.19
Pass
8
3.5
Pass
25.4 (5 X Uoc)
14.10
Pass
8
3.0
Pass
5*Uoc= 25.25
13.14
Pass
8
2.9
Pass
5*Uoc= 25.2
12.56
Pass
8
3.0
Pass
5*Uoc= 25.25
12.51
Pass
According to Table 2B (normal condition), USB4 port (Uoc = 4.99V)
current (in A)
apparent power (in VA)
For model MS-163Gxxx(Mainboard F)
According to Table 2B (normal condition), USB1 port (Uoc = 5.01V)
current (in A)
apparent power (in VA)
According to Table 2B (normal condition), USB2 port (Uoc = 5.01V)
current (in A)
apparent power (in VA)
According to Table 2B (normal condition), USB3 port (Uoc = 5.01V)
current (in A)
apparent power (in VA)
According to Table 2B (normal condition), USB4 port (Uoc = 5.01V)
current (in A)
apparent power (in VA)
Model: MS-163Nxxx (Mainboard G)
According to Table 2B (normal condition), Left side USB port (Uoc = 5.04V)
current (in A)
apparent power (in VA)
According to Table 2B (normal condition), Right side USB port (Uoc = 5.04V)
current (in A)
apparent power (in VA)
Model: MS-163Pxxxx (Mainboard H)
According to Table 2B (normal condition), USB port (J38) (Uoc = 5.05V)
current (in A)
apparent power (in VA)
According to Table 2B (normal condition), USB port (J39) (Uoc = 5.04V)
current (in A)
apparent power (in VA)
According to Table 2B (normal condition), USB port (JC16) (Uoc = 5.04V)
current (in A)
apparent power (in VA)
According to Table 2B (normal condition), USB port (JC15) (Uoc = 5.05V)
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 80 of 109
current (in A)
apparent power (in VA)
Report No.:
11015280 001
8
2.8
Pass
5*Uoc= 25.25
11.7
Pass
Note(s):
1. Limited by polyswitch (F1).
2. The equipment provided an IEEE1394 port for data transmission only. No LPS test are considered to be
necessary
3. The USB port circuits of Mainboard B are identical to Mainboard A. Test were performed on Mainboard A to
represent Mainboard B.
2.6.3.4
TABLE: ground continue test
Location
N/A
Resistance measured (mΩ) Comments
Note(s):
2.10.2
Table: working voltage measurement
Location
N/A
RMS voltage (V)
Peak voltage (V) Comments
Note(s):
2.10.3 and
2.10.4
TABLE: clearance and creepage distance measurements
Clearance cl and creepage
distance dcr at/of:
Up
(V)
U r.m.s.
(V)
Required
cl (mm)
P
cl
(mm)
Required
dcr (mm)
dcr
(mm)
For model MS-1039xxxxx (TNV board (a))
SELV components (with 10N)
to TNV-3 components (with
10N)
140
125
1.0
2.0
1.5
2.5
SELV trace to TNV trace
140
125
1.0
2.5
1.5
2.5
For model MS-1636xx, MS-1637xx (TNV board (b))
SELV components (with 10N)
to TNV-3 components (with
10N)
140
125
1.0
2.0
1.5
2.0
SELV trace to TNV-3 trace (on
TNV board)
140
125
1.0
4.2
1.5
4.2
For model MS-163Pxxxx (TNV board (c))
SELV components (with 10N)
to TNV-3 components (with
10N)
140
125
1.0
2.0
1.5
2.0
SELV trace to TNV-3 trace (on
TNV board)
140
125
1.0
4.4
1.5
4.4
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 81 of 109
Report No.:
11015280 001
Note(s):
1.
An insulation sheet wrapped around modem card.
2.
The wire of RJ-11 connector was covered by heatshrunk tube.
2.10.5
TABLE: distance through insulation measurements
Distance through insulation di at/of:
P
U r.m.s.
(V)
Test voltage
(V)
Required di
(mm)
di
(mm)
Insulation sheet wrapped around modem card
(supplementary insulation)
125
AC 1500
0.4
0.4
Heatshrunk tube covered wire to RJ-11
connector (supplementary insulation)
125
AC 1500
0.4
0.4
Note(s):
4.5.1
TABLE: maximum temperatures
P
test voltage (V) .....................................................: a. DC 19

b. Power from battery pack
t1 (°C) ...................................................................: --

t2 (°C) ...................................................................: --

Maximum temperature T of part/at:
T (°C)
allowed Tmax
(°C)
Model: MS-1039xxxxx (Mainboard A, with DC Fan source of Forcecon, type 451005M10T (5.1CFM))
a.
--
PCB near U31 of mother board
82.2
105
PCB near CPU heatsink of mother board
60.5
105
PCB near U3 of mother board
76.8
105
PCB near U6 of mother board
70.9
105
PCB near PD5 of mother board
65.5
105
RTC battery of mother board
70.1
--
PCB near U1 of modem card
59.9
105
HDD
53.2
--
DVD RW/CD-RW ROM
53.8
--
Outside of Battery pack
40.9
95
T1 coil of DC/AC inverter
71.5
105
T1 core of DC/AC inverter
69.5
105
LCD panel
47.4
95
Enclosure inside near CPU heatsink
53.4
--
Enclosure outside near CPU heatsink
51.0
95
Test voltage
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 82 of 109
Report No.:
40.0
Max. ambient temperature Tma (°C):
11015280 001
--
Note: ambient air during test were Tamb=30.2°C
For model MS-1636xx with DC fan: LG, type MFNC-C537F
(with Mainboard D, DC fan source of Forcecon, type DFS450805M10T (3CFM))
Test condition
a.
b.
--
PCB near U27
71.5
67.4
105
PCB near U29
84.6
82.5
105
PCB near U25
75.4
75.0
105
PCB near U31
75.6
70.4
105
DDR CHIP
64.8
60.2
--
RTC Battery
67.4
67.5
--
PL9 Body
73.5
68.9
105
PL5 Body
67.7
70.6
105
H.D.D. Body
61.4
64.3
--
DVD ROM
52.8
52.2
--
PCB near U8
69.9
64.4
105
Enclosure inside near U27 (Plastic)
49.2
52.6
--
Enclosure outside near U27 (Plastic)
46.9
60.7
95
Battery pack outside
43.6
60.0
95
PT1 coil
74.4
71.2
105
Enclosure inside near PT1 (Plastic)
60.6
61.0
--
Enclosure outside near PT1 (Plastic)
53.1
76.5
95
Max. ambient temperature Tma (°C):
40.0
40.0
--
Note: ambient air during test were Tamb=23.3°C and 21.7°C
respectively
Test for model: MS-1637xx
(with Mainboard C, DC fan source of Forcecon, type DFS450805M10T (3CFM))
Test voltage
a.
b.
--
PCB near U21 (CPU)
82.1
80.1
105
PCB near U20
77.4
73.3
105
PCB near U25
67.9
68.2
105
PCB near U26
60.9
59.9
105
DDR chipset (touch PCB)
78.6
73.0
105
RTC battery
49.0
51.9
--
Enclosure inside near U21
52.1
54.7
--
Enclosure outside near U21
54.4
55.9
75
ODD body
52.3
54.1
--
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 83 of 109
Report No.:
11015280 001
HDD body
59.8
62.0
--
PCB near U11
50.8
54.0
105
PCB near U9
62.0
65.1
105
T1 coil (DC/AC inverter)
64.1
47.6
105
Enclosure inside near DC/AC inverter
54.9
45.2
--
Enclosure outside near DC/AC inverter
49.7
44.2
95
Battery pack enclosure outside
42.7
60.1
75
Max. ambient temperature Tma (°C):
40.0
40.0
--
Note: ambient air during test were Tamb=26.4°C and 24.1°C
respectively
Test for model: MS-163Axx
(with Mainboard E, DC fan source of Forcecon, type DFS450805M10T (3CFM))
Test voltage
a.
b.
--
PCB near U30 (CPU)
71.7
72.4
105
PCB near U27
73.4
73.6
105
PCB near U32
72.9
72.8
105
DDR chipset (touch PCB)
69.5
69.6
105
RTC battery
69.7
70.0
--
Choke 7 near U30
72.7
71.0
105
PCB near U14
67.2
66.8
105
HDD body
64.8
64.8
--
ODD body
59.8
59.6
--
Enclosure inside near U30
53.1
57.0
--
Enclosure outside near U30
52.1
55.1
75
T1 coil (DC/AC inverter)
72.0
72.3
105
Enclosure inside near DC/AC inverter
57.5
58.9
--
Enclosure outside near DC/AC inverter
52.3
53.1
95
Battery pack enclosure outside
52.8
67.2
75
Max. ambient temperature Tma (°C):
40.0
40.0
--
Note: ambient air during test were Tamb=24.0°C and 24.1°C
respectively
Test for model: MS-163Gxxx
(with Mainboard F, DC fan source of Forcecon, type DFS451205M10T (4.5CFM))
Test voltage
a.
b.
--
85.0
81.7
105
Test for unit
PCB near U27 (CPU)
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 84 of 109
Report No.:
11015280 001
PCB near U33
73.3
72.1
105
PCB near U28
69.2
69.3
105
Memory body (touch PCB)
66.0
65.5
105
RTC battery
70.9
69.2
--
HDD body
65.1
65.5
--
ODD body
55.6
54.8
--
Enclosure inside near U27
61.0
61.9
--
Enclosure outside near U27
57.1
58.4
75
Panel (glass)
50.3
52.4
80
Keyboard body
52.9
53.4
75
Battery pack enclosure outside
48.3
59.1
75
Max. ambient temperature Tma (°C):
40.0
40.0
--
T1 coil (DC/AC inverter)
82.2
--
105
Max. ambient temperature Tma (°C):
40.0
--
--
a.
b.
--
PT1 Coil
74.4
76.6
105
Max. ambient temperature Tma (°C):
40.0
40.0
--
T1 Coil
77.2
79.3
105
Max. ambient temperature Tma (°C):
40.0
40.0
--
Note: ambient air during test were Tamb=27.0°C and 25.7°C
respectively
Test for DC/AC inverter: Mitac / DA-1A08-MS01L
Note: ambient air during test were Tamb= 25.7°C
Test for DC/AC inverter: Sample / YIVNMS0018D11-B
Test Voltage
Note: ambient air during test were Tamb=27.0°C and 27.5°C
respectively
Test for DC/AC inverter: Mitac / DA-1A08-MS02L---
Note: ambient air during test were Tamb=27.0°C and 27.5°C
respectively
For model MS-163Nxxx with DC fan: LG, type MFNC-C537F
(with Mainboard G, DC fan source of Forcecon, type DFS450805M10T (3CFM))
Test condition
a.
b.
--
PT1 coil
82.1
77.6
105
PT1 core
74.1
71.1
105
PWB near IC1
68.9
66.8
105
PWB near U1
42.7
42.8
105
Enclosure inside near PT1
62.1
61.1
--
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 85 of 109
Report No.:
11015280 001
Enclosure outside near PT1
57.5
56.8
95
PWB near U17
69.2
66.1
105
PWB near U24
71.7
70.4
105
PWB near U22
77.2
75.6
105
PWB near U7
54.7
53.6
105
RTC battery body
59.6
58.7
105
DDR Ram board body
74.8
73.1
105
TNV card board body
55.6
54.8
105
DVD/RW ROM body
45.4
45.1
105
HDD body
57.6
59.3
105
Enclosure inside near U22
53.3
54.1
--
Enclosure outside near U22
49.7
49.1
95
Battery pack body
52.3
67.2
95
Max. ambient temperature Tma (°C):
40.0
40.0
--
(A)
(B)
--
PCB near U27 (CPU)
65.5
72.9
105
PCB near U33
65.2
73.1
105
PCB near U38
65.1
72.8
105
PCB near U32
63.8
68.1
105
RTC battery pack
57.8
61.9
100
HDD
53.0
55.7
--
ODD
47.1
46.8
--
PCB near U2 (for Inverter)
74.0
73.8
105
T1 coil (for Inverter)
89.8
88.9
105
Enclosure inside near Inverter transformer (T1)
58.6
58.9
--
Enclosure outside near Inverter transformer (T1)
52.7
53.8
75
Enclosure inside near U27 (CPU)
51.8
58.3
--
Enclosure outside near U27 (CPU)
51.1
55.9
75
Enclosure inside near Battery pack
48.3
66.4
--
Enclosure outside near Battery pack
47.6
65.1
75
Tma
40.0
40.0
--
Note: ambient air during test were Tamb = 26.7°C and 27.2°C
respectively
Test voltage
For mainboard MS-143P1
For DC/AC Inverter:
:Mitac/DA-1A08-MS01L
For Unit
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 86 of 109
Report No.:
11015280 001
Test with model MS-163Pxxxx (Mainboard H), DC/AC Inverter: Mitac /DA-1A08-MS01L, Battery pack:
SIMPLO/SQU-718 (7800mAh), CPU: Intel / Celeron 530, 1.73GHz, DC fan: Forcecon, type
DFS451205M10T (4.5CFM)
Test voltage
A)
B)
--
40.0 (23.3)
40.0 (25.2)
--
PCB near U27 (CPU)
65.5
72.9
105
PCB near U33
65.2
73.1
105
PCB near U38
65.1
72.8
105
PCB near U32
63.8
68.1
105
RTC battery
57.8
61.9
--
HDD body
53.0
55.7
--
ODD body
47.1
46.8
--
PWB near U2 (DC/AC Inverter)
74.0
73.8
105
T1 coil (DC/AC Inverter)
89.8
88.9
105
Enclosure inside near T1
58.6
58.9
--
Enclosure outside near T1
52.7
53.8
75
Enclosure inside near U27
51.8
58.3
--
Enclosure outside near U27
51.1
55.9
75
Enclosure inside near Battery pack
48.3
66.4
--
Enclosure outside near Battery pack
47.6
65.2
75
Test for unit
Tma (Tamb)
Temperature T of winding:
R1
(Ω)
R2
(Ω)
T
(°C)
allowed
Tmax (°C)
insulation
class
Note(s):
The temperatures were measured under worst case normal mode defined in 1.2.2.1 and as described in subclause 1.6.2 and at voltages as described above.
All values for T(°C) are re-calculated from Tamb respectively.
Using maximum ambient temperature of 40°C.
4.5.2
TABLE: ball pressure test of thermoplastic parts
N/A
allowed impression diameter (mm) .................. : ≤ 2 mm
Part

Test temperature
(°C)
Impression diameter
(mm)
Note(s):
4.6.1, 4.6.2 Table: enclosure openings
TRF No.:IECEN60950_1B
P
TRF originator: SGS Fimko
Page 87 of 109
Location
Size (mm)
Report No.:
11015280 001
Comments
For all models
Top
Max. 2.5 by 0.5
Numerous openings for speakers.
Front
Max. 24 by 4.2
One slot for MMC/SD/MS card, internal metal
housing and PCB as barrier.
Right
Max. 55.8 by 6.7
1) For all models except for MS-163Pxxxx:
One slot for PCM/CIA card, and one
plastic dummy card (rated V-1) provided
on the slot during normal operation.
2) For model MS-163Pxxxx only:
One slot for PCM/CIA card provided with
dummy card
Rear
Max. 8.8 by 3.0
Numerous openings which provide copper
heat sink for DC fan, which with width of
1.0mm max. as internal barrier.
For bottom enclosure A
Bottom
Min. 6.8 by 0.8
Numerous openings provided on HDD DOOR
under mesh like(∅1.0mm max, 1.3mm
between centre lines, 0.6 mm wire diameter,
0.45mm in thickness)
Bottom
Min. 3.5 by 1.9
Numerous openings provided on SYSTEM
DOOR under mesh like(∅1.0mm max,
1.3mm between centre lines, 0.6 mm wire
diameter, 0.45mm in thickness)
Bottom
Min. 8.0 by 2.5
Numerous openings provided on DC fan for
CPU used under mesh like(∅1.0mm max,
1.3mm between centre lines, 0.6 mm wire
diameter, 0.45mm in thickness)
For bottom enclosure B
Bottom (on HDD cover)
7.0 x 1.0
28 openings, with internal mesh (the wire
diameter= 0.6mm, between centre lines=
1.5mm, 0.45mm in thickness).
Bottom (on CPU cover)
4.5 x 5.0
Numerous openings, with internal metal
chassis. The internal metal chassis has
numerous openings which width is 0.9mm.
15.0 x 2.1
117.0 x 33.0
27.0 x 15.0
Note(s):
4.7
Table: resistance to fire
Part
P
Manufacturer of material
Type of material
Thickness
(mm)
Flammability
class
Plastic Enclosure
Sabic
C7230
1.0
V-1 min.
Plastic Enclosure
Sabic
C7230P
1.2
V-0 min.
--
--
--
V-1 min.
PCB
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 88 of 109
Report No.:
11015280 001
Note(s):
5.1.8.1
TABLE: TNV touch current measurement
Condition
L→ terminal A
(mA)
N → terminal A
(mA)
P
Limit
(mA)
Comments
Test with TNV board (a) with all adapter sources of DC 19V 4.74A
From L/N to Tip and
Ring
0.03
0.03
0.25
With switch “e” opened.
Test with TNV board (b) with all adapter sources of DC 19V 3.42A
From L/N to Tip and
Ring
0.02
0.02
0.25
With switch “e” opened.
Test with TNV board (b) with all adapter sources of DC 19V 4.74A
To RJ11 Tip & Ring
0.03
0.03
0.25
With switch “e” opened.
0.25
With switch “e” opened.
Test for TNV board (b) with adapter sources of DC 19V 6.3A
To RJ11 Tip & Ring
0.02
0.02
Note(s): Performed all sources of power adapter and modem card, only record the maximum test result.
Input voltage: 264V for adapter
Input frequency: 60Hz for adapter
Overall capacity: in approved adapter
The TNV board (c) does not with any Y-Cap. therefore, the touch current result can be covered by TNV
board (a) or TNV board (b) test with all adapter sources.
5.2
TABLE: electric strength tests and impulse tests
Test voltage applied between:
N/A
Test voltage (V)
Breakdown
Note(s):
5.3
TABLE: fault condition tests
P
ambient temperature (°C) ...................................: 25°C, if not otherwise stated.

model/type of power supply ................................: 2) LSE0202D1990 (used for
models MS-1039, MS-1636
and MS-163G)

2) 0335A1965 (used for
models MS-1637, MS-163C,
MS-163N)
3) ADP-120ZB BB
manufacturer of power supply .............................: 1), 2) Li-Shin

3) Delta
rated markings of power supply ..........................: See appended table 1.5.1
TRF No.:IECEN60950_1B

TRF originator: SGS Fimko
Page 89 of 109
No. Component
no.
Fault
Test voltage
(Vdc)
Test
time
Fuse
no.
Report No.:
11015280 001
Fuse
Result
current (A)
For model MS-1039xxxxx
1.
DC fan for
CPU
stalled
19
1.5 hr
--
--
EUT shutdown after 20 min.,
temperature: PCB under CPU =
o
76.6 C, T1 coil of DC/AC
o
inverter = 64.3 C, enclosure
outside near CPU heatsink =
o
o
52.8 C, ambient = 26.9 C, no
hazard.
2.
All ventilation
openings
blocked
19
2.4 hr
--
--
EUT shutdown after 15 min.,
Temperature: PCB under CPU =
o
70.1 C, T1 coil of DC/AC
o
inverter = 52.7 C, enclosure
outside near CPU heatsink =
o
o
48.2 C, ambient = 26.9 C, no
hazard.
3.
D10 pin 3-2
shorted
(for model MS1034xxxxx)
19
1s
--
--
Reverse current of RTC battery :
3mA.
4.
D2 pin 3-2 (for
model MS1039xxxxx)
shorted
19
1s
--
--
Reverse current of RTC battery :
0.65mA.
5.
CI242 to CN11
pin 1 (for
model MS1034xxxxx)
shorted
19
7 hr
--
--
Reverse current of RTC battery :
0.01mA. Test for all sources of
RTC battery, no hazard.
--
--
Unit shutdown, no hazards.
Test with DC/AC inverter Taiwan Sumida, type TWS-400-9589
6.
T1 pin 6-7 of
DC/AC
inverter
shorted
19
1s
Test with DC/AC inverter: Sampo type YIVNMS0018D11
7.
PT1 pin 5-6 of
DC/AC
inverter
shorted
19
1s
--
--
Unit shutdown, no hazards.
For models MS-1636xx
8.
Openings
Blocke
d
19
2 hr 59
mins.
--
--
Unit shutdown, Max temp:
U29=87.0°C, Ambient=22.3°C,
no hazards.
9.
Fan
Locked
19
13 hr 13
mins.
--
--
Unit shutdown, Max temp:
U29=85.3°C, Ambient=22.3°C,
no hazards.
10.
DT1 pin 1-3
(for RTC
Battery)
shorted
19
1s
--
--
Reverse current of RTC
battery=2.96mA, no hazard.
11.
R326 (for RTC shorted
Battery)
19
1s
--
--
Reverse current of RTC
battery=0A, no hazard.
For models MS-1637xx and MS-163Cxx
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 90 of 109
Report No.:
11015280 001
12.
Openings
Blocke
d
19
4 hr 23
mins.
--
--
Normal operation, Max temp:
PL9=70.6°C, Ambient=22.6°C,
no hazards.
13.
Fan
Locked
19
2 hr 32
mins.
--
--
Normal operation, Max temp:
PL9=72.1°C, Ambient=23.4°C,
no hazards.
14.
DT1 pin 1-3
(for RTC
Battery)
shorted
19
1s
--
--
Reverse current of RTC
battery=2.95mA, no hazard.
15.
R82 (for RTC
Battery)
shorted
19
1s
--
--
Reverse current of RTC
battery=0A, no hazard.
For model MS-1636xx
16.
All ventilation
openings
blocked
19
2 hr 22
mins
--
--
Unit shutdown after 1hr 10min,
max. temp. at PCB near U29=
o
o
78 C, ambient= 23.3 C, no
damaged, no hazard.
17
DC fan for
CPU
stalled
19
1 hr
31mins.
--
--
EUT shutdown after 45min,
max. temp. at PCB near U29=
o
o
73.6 C, ambient= 22.9 C, no
damaged, no hazard.
For model MS-1637xx
18.
All ventilation
openings
blocked
19
5 hr 44
mins.
--
--
Normal operation, max. temp. at
o
DDR chipset= 70.3 C, ambient=
o
26.9 C, no damaged, no hazard.
19.
DC fan for
CPU
stalled
19
1hr
31mins.
--
--
Normal operation, max. temp. at
o
PCB near U21= 84.6 C,
o
ambient= 26.3 C, no damaged,
no hazard.
For model MS-163Axx
20.
All ventilation
openings
blocked
19
2 hr 17
mins.
--
--
EUT shutdown after 50min,
max. temp. at PCB near U30=
o
o
89.3 C, ambient= 23.8 C, no
damaged, no hazard.
21.
DC fan for
CPU
stalled
19
35
mins.
--
--
EUT shutdown after 20min,
max. temp. at PCB near U30=
o
o
81.6 C, ambient= 23.9 C, no
damaged, no hazard.
22.
D24 pin 1-3
shorted
19
1s
--
--
Test for RTC battery, reverse
charging current= 3.19mA.
23.
R477
shorted
19
1s
--
--
Test for RTC battery, no reverse
charging current.
24.
Output ports
overloaded
19
1 min.
--
--
Test for VGA port, S-Video port,
IEEE 1394 port, RJ45 port,
RJ11port, speaker connector,
USB ports, HDMI port and tuner
connector. The energy of
connectors are below 240VA. No
damaged, no hazard.
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 91 of 109
Report No.:
11015280 001
For model MS-163Gxxx
25.
All ventilation
openings
blocked
19
4 hr
--
--
EUT normal operation, max.
o
temp. at PCB near U27= 82.6 C,
o
ambient= 26.8 C, no damaged,
no hazard.
26.
DC fan for
CPU
stalled
19
3 hr
--
--
Unit shutdown after 10mins,
max. temp. at PCB near U27=
o
o
95.0 C, ambient= 27.0 C, no
damaged, no hazard.
27.
DT1 pin 1-3
shorted
19
1s
--
--
Test for RTC battery, reverse
charging current= 3.02mA.
28.
R326
shorted
19
1s
--
--
Test for RTC battery, no reverse
charging current.
29.
Output ports
overloaded
19
1 min.
--
--
Test for VGA port, S-Video port,
IEEE 1394 port, RJ45 port,
audio connectors, USB ports.
The energy of connectors is
below 240VA. No damaged, no
hazard.
--
--
Unit operated normally, no
damaged, no hazards.
For model MS-163Nxxx
1
Ventilation
Blocked
19Vdc
3 hr
Measured max. temp for PWB
near U22: 69.2°C,
Ambient=27.1°C.
2
CPU Fan
Locked
19Vdc
2 hr 36
mins
--
--
Unit operated normally, no
damaged, no hazards.
Measured max. temp for PWB
near U22:80.1°C,
Ambient=26.9°C.
3
R226 of RTC
battery type
CR2032
short
19Vdc
10 mins --
--
Abnormal reverse current: 0A.
Not exceed the max. of
abnormal charging current
4
DT1(Pin 1-3)
of RTC battery
type CR2032
short
19Vdc
10 mins --
--
Abnormal reverse current:
3.0mA. Not exceed the max. of
abnormal charging current
For model MS-163Pxxxx
1
All ventilation
openings
blocked
19
2 hr
--
--
Unit shutdown. The max. temp.
at PCB near CPU (U27)=
o
85.2 C, DC/AC Inverter T1 coil=
o
o
75.1 C, ambient= 26.8 C, no
damaged, no hazard.
2
DC fan for
CPU
stalled
19
1.5 hr
--
--
Unit shutdown. The max. temp.
at PCB near CPU (U27)=
o
78.8 C, DC/AC Inverter T1 coil=
o
o
74.2 C, ambient= 24.4 C, no
damaged, no hazard.
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 92 of 109
Report No.:
11015280 001
3
DT1 pin X-Y
shorted
19
1s
--
--
Test for RTC battery, reverse
charging current= 3.27mA.
4
DT1 pin Z-Y
shorted
19
1s
--
--
Test for RTC battery, reverse
charging current= 3.02mA.
5
R326 of RTC
battery type
CR2032
short
19
10 mins
--
--
Abnormal reverse current: 0A.
Not exceed the max. of
abnormal charging current
Note(s):
6.2.2.1 and TABLE: electric strength tests and impulse tests
6.2.2.2
Test voltage applied between:
P
Test voltage (V)
Breakdown
TNV to keyboard with metal foil
AC 2500
No
TNV to accessible conductive part
AC 1500
No
TNV to SELV circuit
AC 1500
No
TNV to keyboard with metal foil
AC 3000
No
TNV to accessible conductive part
AC 1500
No
TNV to SELV circuit
AC 1500
No
Impulse test
Electric strength test
Note(s): Performed all sources of modem card.
TRF No.:IECEN60950_1B
TRF originator: SGS Fimko
Page 93 of 109
Report No.:
11015280 001
National Differences
Clause
Result – Remark
Requirement − Test
APPENDIX Australian National Differences according to CB Bulletin No. 112A, December
2006 (AS/NZS 60950.1:2003)
Verdict
P
(IEC Publication 60950-1:2001)
EXPLANATION FOR ABBREVIATIONS
P=Pass, F=Fail, N/A=Not applicable. Placed in the column to the right.
Annex ZZ Variations
1.2
Between the definitions for "Person, service" and
"Range, rated frequency" insert the following:
Potential ignition source
1.2.12.15
1.2.12.201
Class III equipment, no direct
connection to the AC mains
supply
After the definition of 1.2.12.15, add the following: Added.
N/A
N/A
1.2.12.201 Potential ignition source:
Possible fault which can start a fire if the opencircuit voltage measured across an interruption or
faulty contact exceeds a value of 50 V (peak) a.c.
or d.c. and the product of the peak value of this
voltage and the measured r.m.s. current under
normal operating conditions exceeds 15 VA.
Such a faulty contact or interruption in an
electrical connection includes those which may
occur in conductive patterns on printed boards.
NOTE 201: An electronic protection circuit may be
used to prevent such a fault from becoming a
potential ignition source.
NOTE 202: This definition is from AS/NZS
60065:2003.
1.5.1
Add the following to the end of first paragraph:
Added.
N/A
Add the following to the end of first and third dash Added.
items:
N/A
"or the relevant Australian/New Zealand
Standard."
1.5.2
"or the relevant Australian/New Zealand
Standard."
2.1
Delete the Note.
Deleted.
N/A
3.2.3
Delete Note 2.
Deleted.
N/A
3.2.5
Modify Table 3B as follows:
Modified.
N/A
Rated current of
equipment A
Over 0.2 up to
and including 3
Nominal
crosssectional
2
area mm
1)
0.5
AWG or kcmil
(cross-sectional
2
area in mm )
see note 2
18 [0.8]
Australian National Differences according to CB Bulletin No. 112A, December 2006
Page 94 of 109
Report No.:
11015280 001
National Differences
Clause
Result – Remark
Requirement − Test
Over 3 up to and
including 7.5
0.75
Over 7.5 up to
and including 10
(0.75) 1.00
Over 10 up to
and including 16
(1.0) 1.5
Verdict
16 [1.3]
2)
16 [1.3]
3)
14 [2]
Replace footnote 1) with the following:
1)
This nominal cross-sectional area is only
allowed for Class II appliances if the length of the
power supply cord, measured between the point
where the cord, or cord guard, enters the
appliances, and the entry to the plug does not
exceed 2 m (0.5 mm² three-core supply flexible
cords are not permitted; see AS/NZS 3191).
Delete Note 1.
4.3.6
Replace paragraph three with:
Replaced.
N/A
Equipment with a plug portion, suitable for
insertion into a 10 A 3-pin flat-pin socket-outlet
complying with AS/NZS 3112, shall comply with
the requirements in AS/NZS 3112 for equipment
with integral pins for insertion into socket-outlets.
4.3.13.5
Add the following to the end of the first paragraph: Added.
N/A
", or AS/NZS 2211.1"
4.7
Add the following paragraph:
See below.
N/A
Add the following after clause 4.7.3.6:
Added.
N/A
4.7.201 Resistance to fire - Alternative tests
However, equipment under
test used materials and
components in compliance
with requirements of IEC
60950-1. Alternative test
methods were not considered.
General
Alternative test methods were
not considered.
For alternative tests refer to clause 4.7.201.
4.7.201
4.7.201.1
Parts of non-metallic material shall be resistant to
ignition and spread of fire.
This requirement does not apply to decorative
trims, knobs and other parts unlikely to be ignited
or to propagate flames originating from inside the
apparatus, or the following:
Components that are contained in an enclosure
having a flammability category of FV-0 according
to AS/NSZ 4695.707 and having openings only for
the connecting wires filling the openings
completely, and for the ventilation not exceeding 1
mm in width regardless of the length.
Australian National Differences according to CB Bulletin No. 112A, December 2006
N/A
Page 95 of 109
Report No.:
11015280 001
National Differences
Clause
Requirement − Test
Result – Remark
Verdict
The following parts which would contribute
negligible fuel to a fire:
small mechanical parts, the mass of which does
not exceed 4 g, such as mounting parts, gears,
cams, belts and bearings;
small electrical components, such as capacitors
3
with a volume not exceeding 1750 mm ,
integrated circuits, transistors and optocoupler
packages, if these components are mounted on
material flammability category FV-1 or better
according to AS/NZS 4695.707
NOTE - In considering how to minimize
propagation of fire and what “small parts” are,
account should be taken of the cumulative effect
of small parts adjacent to each other for the
possible effect of propagating fire from one part to
another.
Compliance is checked by tests of 4.7.201.2,
4.7.201.3, 4.7.201.4 and 4.7.201.5.
For the base materials of printed boards,
compliance is checked by the test of 4.7.201.5.
The tests shall be carried out on parts of nonmetallic material, which have been removed from
the apparatus. When the glow-wire test is carried
out, the parts shall be placed in the same
orientation, as they would be in normal use.
These tests are not carried out on internal wiring.
4.7.201.2
Parts of non-metallic material are subjected to
glow wire test of AS/NZS 4695.2.11, which is
carried out at 550 °C.
Alternative test methods were
not considered.
N/A
Alternative test methods were
not considered.
N/A
Parts for which the glow-wire test cannot be
carried out, such as those made of soft or foamy
material, shall meet the requirements specified in
ISO 9772 for category FH-3 material. The glowwire test shall be not carried out on parts of
materials classified at least FH-3 according to
ISO 9772 provided that the sample was not
thicker than the relevant part.
4.7.201.3
Testing of insulating materials
Parts of insulating materials supporting potential
ignition sources shall be subject to the glow-wire
test of AN/NZS 4695.2.11, which is carried out at
750 °C.
The test shall be also carried out on other parts of
insulating material which are within a distance of
3 mm of the connection.
NOTE - Contacts in components such as switch
contacts are considered to be connections.
Australian National Differences according to CB Bulletin No. 112A, December 2006
Page 96 of 109
Report No.:
11015280 001
National Differences
Clause
Requirement − Test
Result – Remark
For parts, which withstand the glow-wire test but
produce a flame, other parts above the
connection within the envelope of a vertical
cylinder having a diameter of 20 mm and a height
of 50 mm shall be subjected to the needle-flame
test. However, parts shielded by a barrier which
meets the needle-flame test shall not be tested.
The needle-flame test shall be made in
accordance with AS/NZS 4695.2.2 with the
following modifications:
5 Severities
Replace with:
The duration of application of the test flame shall
be 30 s ± 1 s.
8 Test procedure
8.2 Modification:
Replace the first sentence with:
The specimen shall be arranged so that the flame
can be applied to a vertical or horizontal edge as
shown in the examples of figure 1.
8.4 Modification:
The first paragraph does not apply.
Addition:
If possible, the flame shall be applied at least
10 mm from a corner.
8.5 Replacement:
The test shall be made on one specimen. If the
specimen does not withstand the test, the test
may be repeated on two further specimens, both
of which shall then withstand the test.
10 Evaluation of test results
Replace with:
The duration of burning (tb) shall not exceed 30 s.
However, for printed circuit boards, it shall not
exceed 15 s.
The needle-flame test shall not be carried out on
parts of material classified as V-0 or V-1
according to IEC 60695-11-10, provided that the
sample tested was not thicker than the relevant
part.
Australian National Differences according to CB Bulletin No. 112A, December 2006
Verdict
Page 97 of 109
Report No.:
11015280 001
National Differences
Clause
Requirement − Test
Result – Remark
4.7.201.4
Testing in the event of non-extinguishing material Alternative test methods were
not considered.
If parts, other than enclosures, do not withstand
the glow-wire tests of 4.7.201.3, by failure to
extinguish within 30 s after the removal of the
glow-wire tip, the needle-flame test detailed in
4.7.201.3 is made on all parts of non-metallic
material which are within a distance of 50 mm or
which are likely to be impinged upon by flame
during the tests of 4.7.201.3. Parts shielded by a
separate barrier which meets the needle-flame
test need not to be tested.
Verdict
N/A
NOTE 1 - If the enclosure does not withstand the
glow-wire test the equipment is considered to
have failed to meet the requirement of clause
4.7.201 without the need for consequential
testing.
NOTE 2 - If other parts do not withstand the glowwire test due to ignition of the tissue paper and if
this indicates that burring or glowing particles can
fall onto an external surface underneath the
equipment, the equipment is considered to have
failed to meet the requirement of clause 4.7.201
without the need for consequential testing.
NOTE 3 - Parts likely to be impinged upon by the
flame are considered to be those within the
envelope of a vertical cylinder having a radius of
10 mm and a height equal to the height of the
flame, positioned above the point of the material
supporting in contact with or in close proximity to
connections.
4.7.201.5
Testing of printed boards
The base material of printed boards is subjected
to needle-flame test to Clause 4.7.201.3. The
flame is applied to the edge of the board where
the heat sink effect is lowest when the board is
positioned as in normal use. The flame shall not
be applied to an edge, consisting of broken
perforations, unless the edge is less than 3 mm
for a potential ignition source.
Alternative test methods were
not considered.
The test is not carried out if the –
Printed board does not carry any potential ignition
source;
Base material of printed boards, on which the
available apparent power at a connection
exceeds 15 VA operating at a voltage
exceeding 50 V and equal or less than 400 V
(peak) a.c. or d.c. under normal operating
conditions, is of flammability category FV-1 or
better according to AS/NZS 4695.707, or the
printed boards are protected by an enclosure
meeting the flammability category FV-0
Australian National Differences according to CB Bulletin No. 112A, December 2006
N/A
Page 98 of 109
Report No.:
11015280 001
National Differences
Clause
Requirement − Test
Result – Remark
Verdict
according to AS/NZS 4695.707, or made of
metal, having openings only for connecting
wires which fill the opening completely, or
Base material of printed boards, on which the
available apparatus power at a connection
exceeds 15 VA operating at a voltage
exceeding 400 V (peak) a.c. or d.c. under
normal operating conditions, and base material
printed boards supporting spark gaps which
provide protection against overvoltages, is of
flammability category FV-0 according to
AS/NSZ 4695.707 or the printed boards are
contained in a metal enclosure, having
openings only for connecting wires fill the
openings completely.
Compliance is determined using the smallest
thickness of the material.
NOTE - Available apparent power is the
maximum apparent power, which can be drawn
from the supplying circuit through a resistive load
whose value is chosen to maximise the apparent
power for more than 2 min when the circuit
supplied is disconnected.
6.2.2
Add the following after the first paragraph:
See IEC 60950-1 report.
P
See IEC 60950-1 report.
P
In Australia (this variation does not apply in New
Zealand), compliance with 6.2.2 is checked by the
tests of both 6.2.2.1 and 6.2.2.2.
Delete the note.
6.2.2.1
Delete Note 2.
Add the following after the first paragraph:
In Australia (this variation does not apply in New
Zealand), the electrical separation is subjected to
10 impulses of alternating polarity, using the
impulse test generator of annex N for 10/700 µs
impulses. The interval between successive
impulses is 60 s and the initial voltage, Uc, is:
- for 6.2.1 a):
7.0 kV for hand-held telephones and for
headsets and 2.5 kV for other equipment; and
- for 6.2.1b) and 6.2.1c):
1.5 kV.
NOTE 201 - The 7 kV impulse simulates lightning
surges on typical rural and semi-rural network
lines.
NOTE 202 – The 2.5 kV impulse for 6.2.1a) was
chosen to ensure adequacy of the insulation
concerned and does not necessarily simulate
Australian National Differences according to CB Bulletin No. 112A, December 2006
Page 99 of 109
Report No.:
11015280 001
National Differences
Clause
Result – Remark
Requirement − Test
Verdict
likely overvoltages.
6.2.2.2
Delete the note.
See IEC 60950-1 report.
P
Add the following after the second paragraph:
In Australia (this variation does not apply in New
Zealand), the a.c. test voltage is:
- for 6.2.1a):
3 kV; and
- for 6.2.1b) and 6.2.1c):
1.5 kV.
NOTE 201 – Where there are capacitors across
the insulation under test, it is recommended that
d.c. test voltages are used.
NOTE 202 – The 3 kV and 1.5 kV values have
been determined considering the low frequency
induced voltages from the power supply
distribution system.
Annex P
Add the following Normative References to Annex Added.
P:
IEC 60065, Audio, Video and similar electronic
apparatus - Safety requirements
AS/NZS 3112, Approval and test specification Plugs and socket-outlets
AS/NZS 3191, Approval and test specification Electric flexible cords
AS/NZS 4695.707, Fire hazard testing of
electrotechnical products - Methods of test for the
determination of the flammability of solid electrical
insulating materials when exposed to an igniting
source
Australian National Differences according to CB Bulletin No. 112A, December 2006
N/A
Page 100 of 109
Report No.:
11015280 001
National Differences
Clause
Result – Remark
Requirement − Test
APPENDIX Canadian National Differences according to CB Bulletin No. 112A, December
2006 (CAN/CSA C22.2 No. 60950-1/UL60950-1)
Verdict
P
(IEC Publication 60950-1:2001)
EXPLANATION FOR ABBREVIATIONS
P=Pass, F=Fail, N/A=Not applicable. Placed in the column to the right.
Special National Conditions
1.1.1
All equipment is to be designed to allow
installations in accordance with the National
Electrical Code (NEC), ANSI/NFPA 70,the
Canadian Electrical Code (CEC), Part I,
CAN/CSA C22.1, and when applicable, the
National Electrical Safety Code, IEEE C2. Also,
unless marked or otherwise identified, installation
is allowed per the Standard for the Protection of
Electronic Computer/Data-Processing Equipment,
ANSI/NFPA 75.
Unit was evaluated according
to IEC 60950-1.
1.4.14
For Pluggable Equipment Type A, the protection
in the installation is assumed to be 20A.
No direct mains connection.
N/A
1.5.5
For lengths exceeding 3.05 m, external
interconnecting flexible cord and cable
assemblies are required to be a suitable cable
type (e.g. DP, CL2) specified in the NEC.
No external interconnecting
cable provided.
N/A
Class III equipment.
N/A
N/A
The requirements have to be
checked during national
approval.
For lengths 3.05 m or less, external
interconnecting flexible cord and cable
assemblies that are not types specified in the
NEC are required to have special construction
features and identification markings.
1.7.1
Equipment for use on a.c. mains supply systems
with a neutral and more than one phase
conductor (e.g. 120/240 V, 3-wire) require a
special marking format for electrical ratings.
A voltage rating that exceeds an attachment plug
cap rating is only permitted if it does not exceed
the extreme operating conditions in Table 2 of
CAN/CSA C22.2 No. 235, and if it is part of a
range that extends into the Table 2 “Normal
Operating Conditions.” Likewise, a voltage rating
shall not be lower than the specified “Normal
Operating Conditions,” unless it is part of a range
that extends into the “Normal Operating
Conditions.”
2.5
Where a fuse is used to provide Class 2, Limited No applied for
Power Source, or TNV current limiting, it shall not
be operator-accessible unless it is not
interchangeable.
Canadian National Differences according to CB Bulletin No. 112A, December 2006
N/A
Page 101 of 109
Report No.:
11015280 001
National Differences
Clause
Requirement − Test
Result – Remark
2.7.1
Suitable NEC/CEC branch circuit protection rated Class III equipment.
at the maximum circuit rating is required for all
standard supply outlets, receptacles and mediumbase or smaller lampholders if the supply branch
circuit protection is not suitable.
Verdict
N/A
Power distribution transformers distributing power
at 100 volts or more, and rated 10 kVA or more,
require transformer overcurrent protection.
3.2
Wiring methods (terminals, leads, etc.) used for
the connection of the equipment to the mains
shall be in accordance with the NEC/CEC.
Class III equipment.
N/A
3.2.1
Power supply cords are required to have
attachment plugs rated not less than 125 percent
of the rated current of the equipment.
No power supply cord
provided.
N/A
3.2.3
Permanent connection of equipment to the mains Class III equipment. No direct
supply by a power supply cord is not permitted,
main connection.
except for certain equipment, such as ATMs.
N/A
3.2.5
Power supply cords are required to be no longer
than 4.5 m in length.
No power supply cord
provided.
N/A
Class III equipment. No direct
mains connection.
N/A
Flexible power supply cords are required to be
compatible with Article 400 of the NEC, and
Tables 11 and 12 of the CEC.
3.2.9
Permanently connected equipment is required to
have a suitable wiring compartment and wire
bending space.
3.3
Wiring terminals and associated spacings for field Class III equipment.
wiring connections shall comply with CSA C22.2
No. 0.
N/A
3.3.3
Wire binding screws are not permitted to attach
conductors larger than 10 AWG (5.3 mm²).
Class III equipment.
N/A
3.3.4
Terminals for permanent wiring, including
Class III equipment.
protective earthing terminals, are required to be
suitable for U.S./Canadian wire gauge sizes, rated
125 percent of the equipment rating, and be
specially marked when specified (1.7.7).
N/A
3.4.2
Motor control devices are required for cordNo motor control devices.
connected equipment with a motor if the
equipment is rated more than 12A, or if the motor
has a nominal voltage rating greater than 120V,
or is rated more than 1/3 hp (locked rotor current
over 43 A)
N/A
3.4.8
Vertically-mounted disconnect switches and
No such switch provided.
circuit breakers are required to have the ”on”
position indicated by the handle in the up position.
N/A
Canadian National Differences according to CB Bulletin No. 112A, December 2006
Page 102 of 109
Report No.:
11015280 001
National Differences
Clause
Requirement − Test
Result – Remark
3.4.11
For computer room applications, equipment with
battery systems capable of supplying 750 VA for
five minutes are required to have a battery
disconnect means that may be connected to the
computer room remote power-off circuit.
Not applicable.
4.3.12
The maximum quantify of flammable liquid stored No flammable liquid.
in equipment is required to comply with NFPA 30.
N/A
4.3.13
Equipment with lasers is required to meet Code of
Federal Regulations 21 CFR 1040 (and the
Canadian Radiation Emitting Devices Act, REDR
C1370).
N/A
Optical radiation in compliance
with requirements of IEC
60825-1 (see corresponding
sections of this test report).
Verdict
N/A
Overall compliance needs to
be evaluated during national
approval.
4.7
For computer room applications, automated
Not information storage
information storage systems with combustible
systems.
media greater than 27 cubic feet are required to
have a provision for connection of either
automatic sprinklers or a gaseous agent
extinguishing system with an extended discharge.
N/A
4.7.3.1
For computer room applications, enclosures with Not information storage
combustible material measuring greater than 0.9 systems.
m² or a single dimension greater than 1.8 m are
required to have a flame spread rating of 50 or
less. For other applications, enclosures with the
same dimensions require a flame spread rating of
200 or less.
N/A
Annex H
Equipment that produces ionizing radiation is
required to comply with the Code of Federal
Regulations, 21 CFR 1020 (and the Canadian
Radiation Emitting Devices Act, REDR C1370).
N/A
No ionizing radiation.
Other differences
1.5.1
Components of equipment must be suitable for
the application, and must comply with the
requirements of the equipment standard and the
applicable national (Canadian and/or U.S.)
component or material standards, as far as they
may apply.
Components are approved,
see component list 1.5.1.
The acceptance will be based on the following:
A component Certified by a Canadian or U.S.
National Certification Body (NCB) to a Canadian
or U.S. component standard will be checked for
correct application and use in accordance with its
specified rating. Where necessary, it will also be
subject to the applicable tests of the equipment
standard.
A component, which has a CB Test Certificate for
compliance with a relevant IEC component
standard, will be checked for correct application
Canadian National Differences according to CB Bulletin No. 112A, December 2006
P
Page 103 of 109
Report No.:
11015280 001
National Differences
Clause
Requirement − Test
Result – Remark
Verdict
and use in accordance with its specified ratings.
Where necessary, it will also be subject to the
applicable tests of the equipment standard, and to
the applicable tests of the Canadian and/or U.S.
component or material standard, under the
conditions occurring in the equipment.
A component, which has no approval as in A) or B)
above or which is used not in accordance with its
specified ratings, will be subject to the applicable
tests of the equipment standard, and to the
applicable tests of the Canadian and/or U.S.
component or material standard, under the
conditions occurring in the equipment.
Some components may require annual re-testing,
which may be carried out by the manufacturer,
CSA International or another laboratory
2.3.1
For TNV-2 and TNV-3 circuits with other than
TNV-3 circuits without other
ringing signals and with voltages exceeding
than ring signals.
42.4 Vpeak or 60 Vd.c., the maximum acceptable
current through a 2000 ohm resistor (or greater)
connected across the voltage source with other
loads disconnected is 7.1 mA peak or 30 mAd.c.
under normal operating conditions.
2.3.2
In the event of a single fault, the limits of 2.2.3
Complied.
apply to SELV Circuits and accessible conductive
parts.
2.6.3.3
When subject to impedance testing, protective
Class III equipment.
earthing and bonding are required to be subjected
to the additional test conditions specified.
N/A
3.2.1.2
Equipment connected to a centralized d.c. power No direct mains connection.
system, and having one pole of the DC mains
input terminal connected to the main protective
earthing terminal in the equipment, is required to
comply with special earthing, writing, marking and
installation instruction requirements.
N/A
4.2.8.1
Enclosures around CRTs with a face diameter of No CRT.
160mm or more are required to reduce the risk of
injury due to the implosion of the CRT.
N/A
4.3.2
Equipment with handles is required to comply with No handles
special loading tests.
N/A
5.1.8.3
Equipment intended to receive telecommunication Less than 0.25mA
ringing signals is required to comply with a special
touch current measurement tests.
6.2.1
Enamel coating on winding wire not considered
electrical separation unless subjected to special
investigation.
No used.
Canadian National Differences according to CB Bulletin No. 112A, December 2006
N/A
P
P
N/A
Page 104 of 109
Report No.:
11015280 001
National Differences
Clause
Requirement − Test
Result – Remark
6.4
Equipment intended for connection to
Shall be evaluated during
telecommunication network outside plant cable is national approval.
required to be protected against overvoltage from
power line crosses in accordance with 6.4 and
Annex NAC.
N/A
6.5
Equipment connected to a telecommunications
network and supplied with an earphone intended
to be held against, or in the ear is required to
comply with special acoustic pressure tests.
Shall be evaluated during
national approval.
N/A
M.2
Continuous ringing signals up to 16 mA only are
permitted if the equipment is subjected to special
installation and performance restrictions.
TNV-3 circuits without other
than ring signals.
N/A
Canadian National Differences according to CB Bulletin No. 112A, December 2006
Verdict
Page 105 of 109
Report No.:
11015280 001
National Differences
Clause
Requirement − Test
Result – Remark
APPENDIX Korean National Differences according to CB Bulletin No. 112A, December 2006
(K60950)
Verdict
P
(IEC Publication 60950-1:2001)
EXPLANATION FOR ABBREVIATIONS
P=Pass, F=Fail, N/A=Not applicable. Placed in the column to the right.
1.5.101
Addition:
No power cord provided.
N/A
The CISPR requirements have
to be considered during
national approval.
N/A
Plugs for the connection of the apparatus to the
supply mains shall comply with the Korean
requirement (KSC 8305).
7
Addition: EMC
The apparatus shall comply with the relevant
CISPR standards.
Korean National Differences according to CB Bulletin No. 112A, December 2006
Page 106 of 109
Report No.:
11015280 001
National Differences
Clause
Result – Remark
Requirement − Test
APPENDIX US National Differences according to CB Bulletin No. 112A, December 2006
(UL 60950-1)
Verdict
P
(IEC Publication 60950-1:2001)
EXPLANATION FOR ABBREVIATIONS
P=Pass, F=Fail, N/A=Not applicable. Placed in the column to the right.
Special National Conditions
1.1.1
All equipment is to be designed to allow
installations in accordance with the National
Electrical Code (NEC), ANSI/NFPA 70,the
Canadian Electrical Code (CEC), Part I,
CAN/CSA C22.1, and when applicable, the
National Electrical Safety Code, IEEE C2. Also,
unless marked or otherwise identified, installation
is allowed per the Standard for the Protection of
Electronic Computer/Data-Processing Equipment,
ANSI/NFPA 75.
Unit was evaluated according
to IEC 60950-1.
1.4.14
For Pluggable Equipment Type A, the protection
in the installation is assumed to be 20A.
No direct mains connection.
N/A
1.5.5
For lengths exceeding 3.05 m, external
interconnecting flexible cord and cable
assemblies are required to be a suitable cable
type (e.g. DP, CL2) specified in the NEC.
No external interconnecting
cable provided.
N/A
Class III equipment.
N/A
N/A
The requirements have to be
checked during national
approval.
For lengths 3.05 m or less, external
interconnecting flexible cord and cable
assemblies that are not types specified in the
NEC are required to have special construction
features and identification markings.
1.7.1
Equipment for use on a.c. mains supply systems
with a neutral and more than one phase
conductor (e.g. 120/240 V, 3-wire) require a
special marking format for electrical ratings.
A voltage rating that exceeds an attachment plug
cap rating is only permitted if it does not exceed
the extreme operating conditions in Table 2 of
CAN/CSA C22.2 No. 235, and if it is part of a
range that extends into the Table 2 “Normal
Operating Conditions.” Likewise, a voltage rating
shall not be lower than the specified “Normal
Operating Conditions,” unless it is part of a range
that extends into the “Normal Operating
Conditions.”
2.5
2.7.1
Where a fuse is used to provide Class 2, Limited No applied for
Power Source, or TNV current limiting, it shall not
be operator-accessible unless it is not
interchangeable.
Suitable NEC/CEC branch circuit protection rated Class III equipment.
at the maximum circuit rating is required for all
standard supply outlets, receptacles and mediumbase or smaller lampholders if the supply branch
US National Differences according to CB Bulletin No. 112A, December 2006
N/A
N/A
Page 107 of 109
Report No.:
11015280 001
National Differences
Clause
Requirement − Test
Result – Remark
Verdict
circuit protection is not suitable.
Power distribution transformers distributing power
at 100 volts or more, and rated 10 kVA or more,
require transformer overcurrent protection.
3.2
Wiring methods (terminals, leads, etc.) used for
the connection of the equipment to the mains
shall be in accordance with the NEC/CEC.
Class III equipment.
N/A
3.2.1
Power supply cords are required to have
attachment plugs rated not less than 125 percent
of the rated current of the equipment.
No power supply cord
provided.
N/A
3.2.3
Permanent connection of equipment to the mains Class III equipment. No direct
supply by a power supply cord is not permitted,
main connection.
except for certain equipment, such as ATMs.
N/A
3.2.5
Power supply cords are required to be no longer
than 4.5 m in length.
No power supply cord
provided.
N/A
Class III equipment. No direct
mains connection.
N/A
Flexible power supply cords are required to be
compatible with Article 400 of the NEC, and
Tables 11 and 12 of the CEC.
3.2.9
Permanently connected equipment is required to
have a suitable wiring compartment and wire
bending space.
3.3
Wiring terminals and associated spacings for field Class III equipment.
wiring connections shall comply with CSA C22.2
No. 0.
N/A
3.3.3
Wire binding screws are not permitted to attach
conductors larger than 10 AWG (5.3 mm²).
Class III equipment.
N/A
3.3.4
Terminals for permanent wiring, including
Class III equipment.
protective earthing terminals, are required to be
suitable for U.S./Canadian wire gauge sizes, rated
125 percent of the equipment rating, and be
specially marked when specified (1.7.7).
N/A
3.4.2
Motor control devices are required for cordNo motor control devices.
connected equipment with a motor if the
equipment is rated more than 12A, or if the motor
has a nominal voltage rating greater than 120V,
or is rated more than 1/3 hp (locked rotor current
over 43 A)
N/A
3.4.8
Vertically-mounted disconnect switches and
No such switch provided.
circuit breakers are required to have the ”on”
position indicated by the handle in the up position.
N/A
3.4.11
For computer room applications, equipment with
battery systems capable of supplying 750 VA for
five minutes are required to have a battery
disconnect means that may be connected to the
computer room remote power-off circuit.
N/A
4.3.12
The maximum quantify of flammable liquid stored No flammable liquid.
in equipment is required to comply with NFPA 30.
Not applicable.
US National Differences according to CB Bulletin No. 112A, December 2006
N/A
Page 108 of 109
Report No.:
11015280 001
National Differences
Clause
Requirement − Test
Result – Remark
4.3.13
Equipment with lasers is required to meet Code of
Federal Regulations 21 CFR 1040 (and the
Canadian Radiation Emitting Devices Act, REDR
C1370).
Optical radiation in compliance
with requirements of IEC
60825-1 (see corresponding
sections of this test report).
Verdict
N/A
Overall compliance needs to
be evaluated during national
approval.
4.7
For computer room applications, automated
Not information storage
information storage systems with combustible
systems.
media greater than 27 cubic feet are required to
have a provision for connection of either
automatic sprinklers or a gaseous agent
extinguishing system with an extended discharge.
N/A
4.7.3.1
For computer room applications, enclosures with Not information storage
combustible material measuring greater than 0.9 systems.
m² or a single dimension greater than 1.8 m are
required to have a flame spread rating of 50 or
less. For other applications, enclosures with the
same dimensions require a flame spread rating of
200 or less.
N/A
Annex H
Equipment that produces ionizing radiation is
required to comply with the Code of Federal
Regulations, 21 CFR 1020 (and the Canadian
Radiation Emitting Devices Act, REDR C1370).
N/A
No ionizing radiation.
Other differences
1.5.1
Some components and materials associated with
the risk of fire, electric shock, or personal injury
are required to have component or material
ratings in accordance with the applicable national
(U.S. and Canadian) component or material
requirements. These components include:
Components are approved,
see component list 1.5.1.
attachment plugs, battery packs (rechargeable
type, used with transportable equipment), cathode
ray tubes, circuit breakers, communication circuit
accessories, connectors (used for current
interruption of non-LPS circuits), cord sets and
power supply cords, direct plug-in equipment,
enclosures (outdoor), flexible cords and cables,
fuses (branch circuit), fuseholders, ground-fault
current interrupters, industrial control equipment,
insulating tape, interconnecting cables,
lampholders, limit controls, printed wiring,
protectors for communications circuits,
receptacles, solid state controls, supplementary
protectors, surge suppressors, switches
(including interlock switches), thermal cut-offs,
thermostats, multi-layer transformer winding wire,
tubing, wire connectors, and wire and cables.
US National Differences according to CB Bulletin No. 112A, December 2006
P
Page 109 of 109
Report No.:
11015280 001
National Differences
Clause
Requirement − Test
Result – Remark
2.3.1
For TNV-2 and TNV-3 circuits with other than
TNV-3 circuits without other
ringing signals and with voltages exceeding
than ring signals.
42.4 Vpeak or 60 Vd.c., the maximum acceptable
current through a 2000 ohm resistor (or greater)
connected across the voltage source with other
loads disconnected is 7.1 mA peak or 30 mA d.c.
under normal operating conditions.
2.3.2
In the event of a single fault, the limits of 2.2.3
Complied.
apply to SELV Circuits and accessible conductive
parts.
2.6.3.3
When subject to impedance testing, protective
Class III equipment.
earthing and bonding are required to be subjected
to the additional test conditions specified.
N/A
3.2.1.2
Equipment connected to a centralized d.c. power No direct mains connection.
system, and having one pole of the DC mains
input terminal connected to the main protective
earthing terminal in the equipment, is required to
comply with special earthing, writing, marking and
installation instruction requirements.
N/A
4.2.8.1
Enclosures around CRTs with a face diameter of No CRT.
160mm or more are required to reduce the risk of
injury due to the implosion of the CRT.
N/A
4.3.2
Equipment with handles is required to comply with No handles
special loading tests.
N/A
5.1.8.3
Equipment intended to receive telecommunication Less than 0.25mA
ringing signals is required to comply with a special
touch current measurement tests.
6.2.1
Enamel coating on winding wire not considered
electrical separation unless subjected to special
investigation.
6.4
Equipment intended for connection to
Shall be evaluated during
telecommunication network outside plant cable is national approval.
required to be protected against overvoltage from
power line crosses in accordance with 6.4 and
Annex NAC.
N/A
6.5
Equipment connected to a telecommunications
network and supplied with an earphone intended
to be held against, or in the ear is required to
comply with special acoustic pressure tests.
Shall be evaluated during
national approval.
N/A
M.2
Continuous ringing signals up to 16 mA only are
permitted if the equipment is subjected to special
installation and performance restrictions.
TNV-3 circuits without other
than ring signals.
N/A
No used.
US National Differences according to CB Bulletin No. 112A, December 2006
Verdict
N/A
P
P
N/A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement