SD-4980SU DVD Video Player User`s Manual

SD-4980SU DVD Video Player User`s Manual
Introduction
Connections
2
18
DIGITAL VIDEO
Basic playback
DVD VIDEO PLAYER
SD-4980SU
Advanced playback
Function setup
OWNER’S MANUAL
Others
© 2005 Toshiba Corporation
p.1-4980SU.pmd
1
6/10/2005, 10:30 AM
26
34
54
64
Introduction
SAFETY PRECAUTIONS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
The symbol for CLASS II (Double Insulation)
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT
INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO
QUALIFIED PERSONNEL ONLY.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION:
POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
CAUTION:
This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and
retain for future reference. Should the unit require maintenance, contact an authorized
service location.
Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure.
Visible and invisible laser radiation when open and interlocks defeated.
DO NOT STARE INTO BEAM.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rule. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications made to this equipment, not expressly approved by Toshiba, or
parties authorized by Toshiba, could void the user’s authority to operate the equipment.
2
p2-17-4980SU.pmd
2
6/10/2005, 10:31 AM
The instructions shall state that an ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm
in each pole shall be incorporated in the electrical installation of the building.
These servicing instructions are for use by qualified service personnel only. To reduce
the risk of electric shock do not perform any servicing other than that contained in the
operating instructions unless you are qualified to do so.
Introduction
CAUTION:
In the spaces provided below, record the Model and Serial No. located on the rear panel of your DVD
video player.
Model No.
Serial No.
Retain this information for future reference.
Location of the required label
MANUFACTURED
SERIAL NO.
Be aware that this equipment is still powered even after the ON/STANDBY indicator turns off (standby
mode) by pressing the ON/STANDBY button. To disconnect this equipment completely from the mains
power, pull out the power plug from the wall outlet.
3
p2-17-4980SU.pmd
3
6/10/2005, 10:31 AM
Introduction
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
4
p2-17-4980SU.pmd
4
6/10/2005, 10:31 AM
CTIONS
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Introduction
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12.Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
S3125A
5
p2-17-4980SU.pmd
5
6/10/2005, 10:31 AM
Introduction
IMPORTANT SAFETY INSTRUCTIONS
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
ADDITIONAL SAFETY INSTRUCTIONS
15. When you use headphones, keep the volume at a moderate level. If you use the headphones continuously
with high volume sound, it may cause hearing damage.
16. Do not overload wall outlets; extension cords, or integral convenience receptacles as this can result in a
risk of fire or electric shock.
17. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
6
p2-17-4980SU.pmd
6
6/10/2005, 10:31 AM
CTIONS
18. Keep your fingers well clear of the disc tray as it is closing. Neglecting to do so may cause serious
personal injury.
Introduction
19. Do not place a heavy object on or step on the apparatus. The object may fall, causing serious personal
injury and serious damage to the apparatus.
20. Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious
personal injury and apparatus malfunction.
21. If the apparatus should smoke or smell, immediately disconnect the power cord from the wall outlet. Wait
until the smoke or smell stops, then ask your dealer for a check and repair. Neglecting to do so may cause
fire.
22. While it is thundering, do not touch the connecting cables or the apparatus.
23. The apparatus includes lead, an ingredient of solder used on the PCB, which is a harmful substance to
human and the environment. When disposing of this apparatus, follow the rules and regulations in your
area.
7
p2-17-4980SU.pmd
7
6/10/2005, 10:31 AM
Introduction
Precautions
Notes on handling
Notes on moisture condensation
When shipping the DVD video player, the original
shipping carton and packing materials come in handy.
For maximum protection, repack the unit as it was
originally packed at the factory. Take care not to give
it a shock or shake when carrying.
Do not use volatile liquids, such as insect spray, near
the DVD video player. Do not leave rubber or plastic
products in contact with the DVD video player for a
long time. They will leave marks on the finish.
The top and rear panels of the DVD video player may
become warm after a long period of use. This is not a
malfunction.
When the DVD video player is not in use, be sure to
remove the disc and turn off the power.
If you do not use the DVD video player for a long
period, the unit may not function properly in the
future. Turn on and use the DVD video player
occasionally.
Notes on locating
Place the DVD video player on a level surface. Do not
use it on a shaky or unstable surface such as a
wobbling table or inclined stand. The loaded disc may
come off the proper position and cause damage to
the DVD video player.
When you place this DVD video player near a TV,
radio, or VCR, the playback picture may become poor
and the sound may be distorted. In this case, place
the DVD video player away from the TV, radio, or
VCR.
Moisture condensation damages the DVD video player.
Please read the following carefully.
Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the optical pick-up lens
inside this unit, one of the most crucial internal parts of
the DVD video player.
Moisture condensation occurs during the following
cases.
When you bring the DVD video player directly from a
cold place to a warm place.
When you use the DVD video player in a room where
you just turned on the heater, or a place where the
cold wind from the air conditioner directly hits the
unit.
In summer, when you use the DVD video player in a
hot and humid place just after you move the unit from
an air conditioned room.
When you use the DVD video player in a humid place.
Notes on cleaning
Use a soft, dry cloth for cleaning.
For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe
it dry.
Do not use any type of solvent, such as thinner and
benzine, as they may damage the surface of the DVD
video player.
If you use a chemical saturated cloth to clean the
unit, follow that product’s instructions.
Inspection and Maintenance
Do not use the DVD video player when moisture
condensation may occur.
If you use the DVD video player in such a situation, it
may damage discs and internal parts. Remove the
disc, connect the power cord of the DVD video player
to the wall outlet, turn on the DVD video player, and
leave it for two or three hours. After two or three
hours, the DVD video player will have warmed up and
evaporated any moisture. Keep the DVD video player
connected to the wall outlet and moisture
condensation will seldom occur.
This DVD video player is a high technology, precision
device. If the optical pick-up lens and disc drive parts
become dirty or worn down, the picture quality may be
reduced. To avoid reduction in picture quality, it is
recommended that regular inspection and maintenance
(cleaning or parts replacement) be performed every
1,000 hours of use. For further details, contact your
nearest consumer electronics dealer.
8
p2-17-4980SU.pmd
8
6/10/2005, 10:31 AM
Notes on Discs
Structure of disc contents
Do not touch the playback side of the disc.
Introduction
On handling discs
Normally, DVD video discs are divided into titles, and
the titles are sub-divided into chapters. VIDEO CDs and
audio CDs are divided into tracks.
DVD video disc
DVD video disc
Title 1
Playback side
Chapter 1
Title 2
Chapter 2
Chapter 1
Chapter 2
Chapter 3
Do not attach paper or tape to discs.
VIDEO CD/audio CD
VIDEO CD/audio CD
Track 1
Track 2
Track 3
Track 4
Track 5
On cleaning discs
Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc
clean.
Each title, chapter or track is assigned a number, which
is called “title number”, “chapter number” or “track
number” respectively.
There may be discs that do not have these numbers.
Notes on copyright
If you cannot wipe off the dust with a soft cloth, wipe
the disc lightly with a slightly moistened soft cloth and
finish with a dry cloth.
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or antistatic
spray for vinyl LPs. It may damage the disc.
On storing discs
Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.
The unauthorized recording, use, distribution, or
revision of copyrighted materials including, without
limitation, television programs, videotapes, and DVDs, is
prohibited under the Copyright Laws of the United
States and other countries, and may subject you to civil
and criminal liability.
This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is
prohibited.
9
p2-17-4980SU.pmd
9
6/10/2005, 10:31 AM
Introduction
Notes on Discs (continued)
About this owner’s manual
This owner’s manual explains the basic instructions of
this DVD video player. Some DVD video discs are
produced in a manner that allows specific or limited
operation during playback. As such, the DVD video
player may not respond to all operating commands. This
is not a defect in the DVD video player. Refer to
instruction notes of discs.
“
” may appear on the TV screen during operation.
” means that the operation is not permitted by the
A“
DVD video player or the disc.
Playable discs
This DVD video player can play the following discs.
Disc Mark
Contents
Disc
Size
Maximum
playback time
Approx. 4 hours
(single sided disc)
12 cm
Audio
+
video
(moving
pictures)
DVD
video
discs
Approx. 8 hours
(double sided disc)
Approx. 80 minutes
(single sided disc)
8 cm
Approx. 160 minutes
(double sided disc)
Notes on region numbers
The region number of this DVD video player is 1. If
region numbers, which stand for their playable area, are
printed on your DVD video disc and you do not find
or
, disc playback will not be allowed by the player.
(In this case, the DVD video player will display a
message on-screen.)
VIDEO
CDs
DIGITAL VIDEO
Audio
+
video
(moving
pictures)
Some DVDs that have no region code label may still be
subject to area restrictions and therefore not playable.
Audio
CDs
On VIDEO CDs
This DVD video player supports VIDEO CDs equipped
with the PBC (Version 2.0) function. (PBC is the
abbreviation of Playback Control.) You can enjoy two
playback variations depending on types of discs.
• VIDEO CD not equipped with PBC function
(Version 1.1)
Sound and movie can be played on this DVD video
player in the same way as an audio CD.
• VIDEO CD equipped with PBC function
(Version 2.0)
In addition to operation of a VIDEO CD not equipped
with the PBC function, you can enjoy playback of
interactive software with search function by using the
menu displayed on the TV screen (Menu Playback).
Some of the functions described in this owner’s
manual may not work with some discs.
12 cm
Approx. 74 minutes
8 cm
Approx. 20 minutes
12 cm
Approx. 74 minutes
8 cm
(CD
single)
Approx. 20 minutes
Audio
The following discs are also available.
DVD-R discs of DVD video format
CD-R/CD-RW discs of CD-DA, Video CD, MP3, WMA
or JPEG format
Some of these discs may be incompatible.
• You cannot play discs other than those listed above.
• You cannot play DVD-RAM discs or
non-standardized discs, etc., even if they may be
labeled as above.
• This DVD video player uses the NTSC color system,
and cannot play DVD video discs recorded in any
other color system (PAL, SECAM, etc.).
Because of problems and errors that can occur during
the creation of DVD and Video CD software and/or the
manufacture of DVD and Video CD discs, Toshiba
cannot guarantee that this DVD video player will play
every feature of every DVD bearing the DVD logo and/or
every Video CD bearing the CD logo. As one of the
creators of DVD technology, Toshiba DVD players are
manufactured using the highest standards of quality,
and as a result, such incompatibilities are rare. If you
happen to experience any difficulty playing a DVD on a
Toshiba DVD player, please feel free to call our Call
Centre (see page 67 ).
10
p2-17-4980SU.pmd
10
6/10/2005, 10:31 AM
Table of Contents
Advanced playback
SAFETY PRECAUTIONS .......................... 2
IMPORTANT SAFETY INSTRUCTIONS ... 4
Precautions .............................................. 8
Notes on Discs ......................................... 9
Notes on region numbers ............................... 10
Table of Contents ................................... 11
Identification of Controls ....................... 12
Front panel ..................................................... 12
Rear panel ...................................................... 12
DVD display .................................................... 13
Remote control ............................................... 14
Loading batteries ........................................... 15
Operating with the remote control .................. 15
Connections
Connecting to a TV ................................. 18
Connecting to a TV ......................................... 18
Connecting to an audio system and TV
equipped with component video inputs ....... 19
Connecting to a display
(Using a HDMI cable) ................................... 20
Connecting to Optional Equipment ...... 21
Connecting to an amplifier equipped with a
Dolby Digital decoder ................................... 22
Connecting to an amplifier equipped with
Dolby Surround Pro Logic ............................ 22
Connecting to an amplifier equipped with a
DTS decoder ................................................ 23
Connecting to an amplifier equipped with an
MPEG2 audio decoder ................................. 23
Connecting to an amplifier equipped with a
digital audio input ......................................... 24
Basic playback
Playing a Disc ......................................... 26
Basic playback ............................................... 26
Variable Speed Playback ....................... 28
Playing in fast reverse or fast forward
directions ...................................................... 28
Playing frame by frame .................................. 28
Playing in slow-motion ................................... 29
Resuming playback from the same location .. 29
Locating a Desired Section ................... 30
Locating a title using the top menu ................ 30
Locating a desired section by entering the
corresponding number ................................. 31
Locating a specific chapter or track ............... 31
Introduction
Introduction
Accessing a Specific Location Directly ... 34
Entering the time counter of the desired
location ......................................................... 34
Repeating a Specific Segment .............. 35
Repeating a specific segment ........................ 35
Playing in a Varied Order ....................... 36
Playing titles, chapters or tracks in a varied
order ............................................................. 36
Playing in a Favorite Order .................... 37
Setting titles, chapters, or tracks in a favorite
order ............................................................. 37
Zooming a Picture .................................. 38
Zooming a picture .......................................... 38
Selecting the Picture Enhancement
(E.P.M.) .................................................... 39
Selecting the picture enhancement ................ 39
Selecting the Sound Enhancement
(E.A.M.) ................................................... 40
Selecting the sound enhancement ................. 40
Selecting the Camera Angle .................. 41
Changing the camera angle ........................... 41
Selecting Subtitles ................................. 42
Selecting a subtitle language ......................... 42
Selecting a Language ............................ 43
Selecting a playback audio setting ................. 43
On-screen Display Operation ................ 44
On-screen display operation .......................... 44
Playing MP3/WMA Files ......................... 46
Playing MP3/WMA files .................................. 46
Viewing JPEG Files ................................ 48
Viewing JPEG files ......................................... 48
Viewing a thumbnail view ............................... 49
Playing DivX® MPEG-4 Files .................. 51
Playing DivX® MPEG-4 files ........................... 51
Function setup
Customizing the Function Settings ...... 54
Setting procedure ........................................... 54
Setting details ................................................. 56
Table of Languages ................................ 62
Others
Before Calling Service Personnel ......... 64
Specifications ......................................... 65
United States Warranty .......................... 66
11
p2-17-4980SU.pmd
11
6/10/2005, 10:31 AM
Introduction
Identification of Controls
See the page in
for details.
Front panel
26
26
13
HDMI button
20
26
26
HDMI indicator
20
15
27
Rear panel
18
HDMI OUT
jack 20
19
OPTICAL OUT
jack 22 23 24
22
18
23
24
19
S VIDEO OUT
jack 18
12
p2-17-4980SU.pmd
12
6/10/2005, 10:31 AM
Introduction
DVD display
DVD display and the blue dvd door brightness can
be set to 3 different mode: Normal - Dim - Off.
See settings in 60 .
Title number
indicator
Play mode
indicator
Memory playback
indicator
Chapter number
indicator
Total playing
time indicator
Track number
indicator
TOTAL
TITLE
GROUP
CHP
TRK
Shuffle playback
indicator
M R
A-B
DVD
VCD
Multifunctional indicator (indicates
operating status or messages, etc.
Angle icon
indicator
Repeat playback
indicator
DVD / VIDEO CD /
CD indicator
The indicators vary depending on the kinds of discs you play.
DVD video disc
VIDEO CD
• During playback:
• During playback:
Example
• During playback:
Example
TITLE
Audio CD
Example
TRK
CHP
TRK
DVD
VCD
Some discs may not display
chapter numbers or elapsed time.
CD
Some discs may not display
chapter numbers or elapsed time.
13
p2-17-4980SU.pmd
13
6/10/2005, 10:31 AM
Introduction
Identification of Controls (continued)
The instructions in this manual describe the functions on the remote control. See the page in
for details.
Remote control
26
26
HDMI button 20
45
38
44
43
41
/
26
30
30
42
30
54
31
27 28
26
27
31
31
28
29
39
28
19
40
31
31
35
54
37
36
* MENU/PBC button
Use the MENU/PBC button to display the menu
included on many DVD video discs. To operate a
menu, follow the instructions in “Locating a title using
the top menu.” 30
14
p2-17-4980SU.pmd
14
6/10/2005, 10:31 AM
1
Open the cover.
2
Insert batteries (AAA size).
Operating with the remote control
Introduction
Loading batteries
Point the remote control at the remote
sensor and press the buttons.
Distance: About 7 m (23 feet) from the front of the
remote sensor
Angle:
About 30° in each direction of the front of
the remote sensor
* Do not expose the remote sensor of the DVD video
player to a strong light source such as direct
sunlight or other illumination. If you do so, you may
not be able to operate the DVD video player via the
remote control.
Make sure to match the + and – on the batteries
to the marks inside the battery compartment.
Caution:
Never throw batteries into a fire.
Note:
• Be sure to use AAA size batteries.
• Dispose of batteries in a designated disposal area.
• Batteries should always be disposed of with the
environment in mind. Always dispose of batteries in
accordance with applicable laws and regulations.
• If the remote control does not operate correctly, or if the
operating range becomes reduced, replace batteries with
new ones.
• When necessary to replace batteries in the remote
control, always replace both batteries with new ones.
Never mix battery types or use new and used batteries in
combination.
• Always remove batteries from remote control if they are
dead or if the remote control is not to be used for an
extended period of time. This will prevent battery acid
from leaking into the battery compartment.
Notes on the remote control
• Direct the remote control at the remote sensor of the DVD
video player.
• When using the remote control, press the buttons at
intervals of about 1 second to ensure the correct mode of
operation.
• Do not drop or give the remote control a shock.
• Do not leave the remote control near an extremely hot or
humid place.
• Do not spill water or put anything wet on the remote
control.
• Do not open the remote control.
15
p2-17-4980SU.pmd
15
6/10/2005, 10:31 AM
p2-17-4980SU.pmd
16
6/10/2005, 10:31 AM
Connections
Read this chapter first to make all necessary
preparations.
Connecting to a TV
Connecting to an audio system
and TV equipped with
component video inputs
Connecting to a display (Using a
HDMI cable)
Connecting to an amplifier
equipped with a Dolby Digital
decoder
Connecting to an amplifier
equipped with Dolby Surround
Pro Logic
Connecting to an amplifier
equipped with a DTS decoder
Connecting to an amplifier
equipped with an MPEG2 audio
decoder
Connecting to an amplifier
equipped with a digital audio
input
p2-17-4980SU.pmd
17
6/10/2005, 10:31 AM
Connections
Connecting to a TV
Connect the DVD video player to your TV.
For details of output sound, see
43
.
Connecting to a TV
• Make the following setting.
On-screen display
Select:
“Digital Output”
“PCM” or
“Bitstream”
54
Page
59
“Video Output”
Composite
* Component
54
58
* Only for analog video out jack (yellow)
connection with progressive scan off.
Notes
• Refer to the owner’s manual of the connected TV as well.
• When you connect the DVD video player to your TV, be sure to turn off the power and unplug both units from the wall outlet
before making any connections.
• If your television set has one audio input, connect the left and right audio outputs of the DVD video player to a Y cable
adapter (not supplied) and then connect to your TV.
• Connect the DVD video player directly to your TV. If you connect the DVD video player to a VCR, TV/VCR combination or
video selector, the playback picture may be distorted as DVD video discs are copy protected.
• Analog audio out will not have sound if DTS playback is selected.
18
p18-24-4980SU.pmd
18
6/10/2005, 10:31 AM
Interlaced outputs (ColorStream®)
Some TVs or monitors are equipped with component video
inputs. Connecting to these inputs allows you to enjoy
higher quality picture playback.
Actual labels for component video inputs may vary
depending on the TV manufacturer. (ex. Y, R-Y, B-Y or Y,
CB, CR)
In some TVs or monitors, the color levels of the playback
picture may be reduced slightly or the tint may change. In
such a case, adjust the TV or monitor for optimum
performance.
Progressive outputs (ColorStream Pro®)
Some TVs or monitors are equipped with component video
inputs that are capable of reproducing a progressively
scanned video signal. Connecting to these inputs allows
you to view the highest quality pictures with less flicker.
Consumers should note that not all high definition
television sets are fully compatible with this product and
may cause artifacts to be displayed in the picture. In case
of 525 progressive scan picture problems, it is
recommended that the user switch the connection to the
“standard definition” output. If there are questions
regarding our TV set compatibility with this model 525p
DVD player, please contact our Customer Service Center.
Connections
Connecting to an audio system and TV equipped with component video inputs
Switching the output signal (interlaced/progressive)
using the remote control
You can temporarily switch the output signal for better picture
quality.
Press PROGRESSIVE on the remote control during stop mode.
Press PROGRESSIVE again to turn off progressive mode.
• Make the following setting.
On-screen display
Select:
“Digital Output”
“PCM” or
“Bitstream”
“Video Output”
Component
Page
54
59
54 58
Notes
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of the equipment
from the wall outlet before making any connections.
• If you place the DVD video player near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the
DVD video player away from the tuner and radio.
• The output sound of the DVD video player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, high volume sound may damage your hearing as well as the speakers.
• Turn off the amplifier before you connect or disconnect the DVD video player’s power cord. If you leave the amplifier power
on, the speakers may be damaged.
• Progressive can be on/off only when “Video Output” is set to Component 58 .
• In component connections, the screen might become pinkish in color when the “Video Output” is set to Composite. This is
not a defect of this unit 58 .
• When Progressive is on, only component video will be output.
• Analog audio out will not have sound if DTS playback is selected.
• When using component video cables, do not connect the S video cable.
ColorStream® and ColorStream Pro® are registered trademarks of Toshiba America Consumer Products, L.L.C.
19
p18-24-4980SU.pmd
19
6/10/2005, 10:31 AM
Connections
Connecting to a TV (Continued)
About HDMITM
HDMI stands for High Definition Multimedia Interface. HDMI
transfers digital audio and uncompressed digital video on a
single cable. As a result, audio cables and video cables
don’t need to be connected separately to a device. In
addition, HDMI is compatible with HDCP (High Bandwidth
Digital Content Protection).
HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
licensing LLC.
Connecting to a display (Using a HDMI cable)
To HDMI
Output
HDMI Cable
(not included)
Available output signals are below:
• 480p (progressive)
• 720p (progressive)
• 1080i (interlace)
HDMI-compatible
display
Set the output resolution for the HDMI output
that best matches your TV’s capabilities
Set an output signal from the HDMI terminal of the DVD
Player in accordance with your TV’s input signal.
Press HDMI button on the front panel or the remote
control changes output signals as below. See the HDMI
indicator and select the appropriate output signal.
Press
HDMI indicator
Video output signal
illuminates “ • 1080i”
1080i (interlace)
Press
illuminates “ • 720p”
720p (progressive)
Press
illuminates “ • 480p”
480p (progressive)
480p, 720p and 1080i are signals created with this
DVD Player from original 480i signal. The resolution of
the picture may not be increased even if they are
selected.
• Make the following setting.
On-screen display
Select:
“Digital Output”
“PCM” or
“Bitstream”
54
59
“Video Output”
Component
54
58
Notes
• Refer to the owner’s manual of the connected TV as well.
• When you connect the DVD video player to your TV, be sure to
turn off the power and unplug both units from the wall outlet
before making any connections.
• Select HDMI mode through the HDMI button of the front panel,
analog video out jack (yellow) will not have video signal.
• If you have a HDMI (with HDCP) equipped monitor or display,
you can connect it to this player using a HDMI cable.
• The HDMI connector outputs uncompressed digital video, as
well as almost every kind of digital audio that the player is
compatible with, including DVD-Video, Video CD/Super VCD,
CD and MP3.
• This unit has been designed to be compliant with HDMI (High
Definition Multimedia Interface) Version 1.1 depending on the
component you have connected. Using a HDMI connection
may result in unreliable signal transfers.
• When using HDMI cable, do not connect to other analog video
outputs.
• Becasue HDMI is an evolving technology, it is possible that
some devices with an HDMI input may not operate properly
with this DVD video player.
20
p18-24-4980SU.pmd
20
Page
6/10/2005, 10:31 AM
Connecting to Optional Equipment
You can enjoy high quality dynamic sounds by connecting the DVD video player
to optional audio equipment.
: Front speaker
: Rear speaker
: Sub woofer
: Center speaker
: Signal flow
Warning
• When you are connecting (via the OPTICAL or
COAXIAL DIGITAL AUDIO OUT jack) an AV decoder
that does not have Dolby Digital, Digital Theater
Systems (DTS) or MPEG2 decoding function, be sure
to set “Digital Output” to “PCM” from the on-screen
displays 54 59 . Otherwise, high volume sound may
damage your hearing as well as the speakers.
• When playing DTS-encoded discs (audio CDs),
excessive noise may be output from the analog audio
output jacks. To avoid possible damage to the audio
system, you should take proper precautions when the
analog audio output jacks of the DVD video player are
connected to an amplification system. To enjoy DTS
Digital Surround™ playback, an external 5.1 channel
DTS Digital Surround™ decoder system must be
connected to the OPTICAL or COAXIAL DIGITAL
AUDIO OUT jack of the DVD video player.
Connections
• For connection to your TV, see “Connecting to a TV”
18 19 20 .
• For details of output sound, see 43 .
• This section uses the following reference marks.
Notes
• DO NOT connect the OPTICAL or COAXIAL DIGITAL
AUDIO OUT jack of the DVD video player to the AC-3 RF
input of a Dolby Digital Receiver. This input on your A/V
Receiver is reserved for Laserdisc use only and is
incompatible with the OPTICAL or COAXIAL DIGITAL
AUDIO OUT jack of the DVD video player.
• Connect the COAXIAL DIGITAL AUDIO OUT jack of the
DVD video player to the “DIGITAL (COAXIAL)” input of a
Receiver or Processor.
• Connect the OPTICAL DIGITAL AUDIO OUT jack of the
DVD video player to the “DIGITAL (OPTICAL)” input of a
Receiver or Processor.
• Refer to the owner’s manual of the connected equipment
as well.
• When you connect the DVD video player to other
equipment, be sure to turn off the power and unplug all of
the equipment from the wall outlet before making any
connections.
• The output sound of the DVD video player has a wide
dynamic range. Be sure to adjust the receiver’s volume to
a moderate listening level. Otherwise, the speakers may
be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect
the DVD video player’s power cord. If you leave the
amplifier power on, the speakers may be damaged.
21
p18-24-4980SU.pmd
21
6/10/2005, 10:31 AM
Connections
Connecting to Optional Equipment
Connecting to an amplifier equipped with a Dolby Digital decoder
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing the
latest movies, and is now available to reproduce this realistic effect in the home.
You can enjoy motion picture and live concert DVD video discs with this dynamic
realistic sound by connecting the DVD video player to a 6 channel amplifier
equipped with a Dolby Digital decoder or Dolby Digital processor. If you have a
Dolby Surround Pro Logic decoder, you will obtain the full benefit of Pro Logic
from the same DVD movies that provide full 5.1-channel Dolby Digital
soundtracks, as well as from titles with the Dolby Surround mark.
Amplifier equipped with a
Dolby Digital decoder
To
COAXIAL
type digital
audio input
To OPTICAL
type digital
audio input
Connect
either.
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and the
double-D symbol are trademarks of Dolby
Laboratories. Confidential unpublished
works. Copyright 1992-1997 Dolby
Laboratories. All rights reserved.
• Use DVD video discs encoded via
the Dolby Digital recording
system.
• Make the following setting.
On-screen display
Select:
Page
“Digital Output”
“PCM” or
“Bitstream”
59
Recording system
D
54
43
Optical digital cable
75 Ω coaxial cable
Connecting to an amplifier equipped with Dolby Surround Pro Logic
Dolby Surround Pro Logic
You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by
connecting an amplifier and speaker system (right and left front speakers, a
center speaker, and one or two rear speakers).
• Make the following setting.
On-screen display
Select:
“Digital Output”
“PCM” or
“Bitstream”
With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an
amplifier equipped with a Dolby Digital decoder.” Refer to that amplifier’s
owner’s manual and set the amplifier so you can enjoy Dolby Surround Pro
Logic sound.
Page
54
59
With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.
*
* Connect one or two rear speakers.
The output sound from the rear speakers
will be monaural even if you connect two
rear speakers.
Amplifier equipped with
Dolby Surround Pro Logic
To audio input
To ANALOG
AUDIO OUT
Audio cable
22
p18-24-4980SU.pmd
22
6/10/2005, 10:31 AM
Connecting to an amplifier equipped with a DTS decoder
Connections
Digital Theater Systems (DTS)
“DTS” and “DTS Digital Out” are
trademarks of Digital Theater Systems,
DTS is a high quality surround technology used in theaters and now available for
Inc.
home use, on DVD video discs or audio CDs.
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1
• Use DVD video discs or audio
channel DTS encoded sound tracks on DVD video discs or audio CDs.
CDs encoded via the DTS
recording system.
• Make the following setting.
Amplifier equipped with
a DTS decoder
To
COAXIAL
type digital
audio input
To OPTICAL
type digital
audio input
Optical digital cable
Connect
either.
On-screen display
Select:
“Digital Output”
“Bitstream”
Recording system
DTS
Page
54
59
43
75 Ω coaxial cable
Connecting to an amplifier equipped with an MPEG2 audio decoder
MPEG2 sound
You can enjoy motion picture and live concert DVD video discs with
dynamic realistic sound by connecting an amplifier equipped with an
MPEG2 audio decoder or MPEG2 audio processor.
Amplifier equipped with an
MPEG2 audio decoder
To
COAXIAL
type digital
audio input
To OPTICAL
type digital
audio input
• Use DVD video discs encoded via
the MPEG2 recording system.
• Make the following setting.
On-screen display
Select:
Page
“Digital Output”
“PCM” or
“Bitstream”
59
Recording system
MPEG2
43
54
Connect
either.
Optical digital cable
75 Ω coaxial cable
23
p18-24-4980SU.pmd
23
6/10/2005, 10:31 AM
Connections
Connecting to Optional Equipment (Continued)
Connecting to an amplifier equipped with a digital audio input
2 channel digital stereo
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an
amplifier equipped with a digital audio input and speaker system (right and left
front speakers).
• Make the following setting.
On-screen display
Select:
“Digital Output”
“PCM”
Amplifier equipped with a
digital audio input
To
COAXIAL
type digital
audio input
To OPTICAL
type digital
audio input
Connect
either.
Optical digital cable
75 Ω coaxial cable
24
p18-24-4980SU.pmd
24
6/10/2005, 10:31 AM
Page
54
59
Basic playback
Begin your operation.
Playing a Disc
Variable Speed Playback
Locating a Desired Section
p25-32-4980.pmd
25
6/10/2005, 10:31 AM
Basic playback
Playing a Disc
This section shows you the basics on how to play a disc.
CAUTION
Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
Basic playback
Preparations
• When you want to view a disc, turn on the TV and select the video input connected to the DVD video player.
• When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the input connected
to the DVD video player.
1
2
Press the ON/STANDBY button.
The DVD video player turns on.
The blue light on the DVD tray door
of the player will light up.
4
Press OPEN/CLOSE to close the disc
tray.
Playback starts.
If you insert a DVD video disc that contains a
top menu, a menu may appear. Use the / /
/
to select the title you want to view, then
press ENTER to start playback. See “Locating a
title using the top menu.” 30
Press OPEN/CLOSE.
The disc tray opens.
• You may need to press the TOP MENU or MENU
button to display disc menu (depending on the
actual DVD video disc.)
3
Place the disc on the disc tray.
With the playback
side down
• There are two different disc sizes. Place the disc in
the correct guide on the disc tray. If the disc is out of
the guide, it may damage the disc and cause the
DVD video player to malfunction.
• Do not place a disc which is unplayable in this DVD
video player.
Notes
• If the disc tray is holding a disc you have already played,
playback will begin from the location where you last
stopped. For resuming playback, see 29 .
• Some video CD are recorded with PBC (Playback
Control), a menu with recorded contents may appear on
the TV if you have turned the PBC on. You can make your
selection according to its PBC menu. Press the MENU/PBC
button on the remote control to turn PBC on or off anytime
during Video CD playback. When switching from PBC off to
PBC on mode, playback will start from the beginning of the
disc.
To start playback in the stop mode
Press PLAY.
26
p25-32-4980.pmd
26
6/10/2005, 10:31 AM
2, 4
1
TOP MENU
To obtain a higher quality picture
Occasionally, some picture noise not usually visible during a normal broadcast
may appear on the TV screen while playing a DVD video disc because the high
resolution pictures on these discs include a lot of information. While the amount of
noise depends on the TV you use with this DVD video player, you should generally
reduce the sharpness adjustment on your TV when viewing DVD video discs.
MENU
About
ENTER
STOP
The
icons on the heading bar show the playable discs for the
function described under that heading.
DVD : You can use this function with DVD video discs.
: You can use this function with VIDEO CDs.
: You can use this function with audio CDs.
CD
PLAY
PAUSE
To turn the power off (To enter the standby
mode)
Press PAUSE/STEP during playback.
To resume normal playback, press
the PLAY button.
• The sound is muted during still
mode.
To stop playback
Press STOP.
Press ON/STANDBY to turn the unit to standby mode.
Note
Be aware that this equipment is still powered even after the
ON/STANDBY indicator turns off (standby mode) by pressing
the ON/STANDBY button. To disconnect this equipment
completely from the main power, pull out the power plug from
the wall outlet.
About the screen saver
When you leave the unit in DVD stop mode for
approximately 2 minutes, the screen saver of the DVD
video player automatically appears. To turn off the
screen saver, press the PLAY button.
To remove the disc
Press OPEN/CLOSE.
Remove the disc after the disc tray
opens completely.
Automatic Power Off function
If the DVD video player is stopped, or the screen saver
is engaged for approximately 20 minutes, the DVD
video player will automatically turn itself off.
Be sure to press the OPEN/CLOSE button to close
the disc tray after you remove the disc.
Notes
• Do not move the DVD video player during playback. Doing so may damage the disc.
• Use the OPEN/CLOSE button to open and close the disc tray. Do not push the disc tray while it is moving. Doing so may
cause the DVD video player to malfunction.
• Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the DVD video
player to malfunction.
• In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen
menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press the
STOP button on your remote control once the movie is completed.
27
p25-32-4980.pmd
27
6/10/2005, 10:31 AM
Basic playback
To pause playback (still mode)
Basic playback
Variable Speed Playback
You can play discs at various speeds, and resume playback from the location
where you stopped playback.
STOP
PAUSE
PLAY
REV
FWD
SLOW
Playing in fast reverse or fast forward directions
Press REV or FWD during playback.
To resume normal playback
Press PLAY.
REV: Fast reverse playback
FWD: Fast forward playback
Each time you press the REV or
FWD button, the playback speed
changes.
Notes
• The DVD video player mutes sound and subtitles during
reverse and forward scan of DVD video discs.
• The playback speed may differ depending on the disc.
Playing frame by frame
Press PAUSE/STEP during still playback.
To resume normal playback
Press PLAY.
Each time you press the PAUSE/
STEP button, the picture advances
one frame.
Note
The sound is muted during frame by frame playback.
28
p25-32-4980.pmd
28
6/10/2005, 10:31 AM
Playing in slow-motion
Basic playback
To resume normal playback
Press SLOW during playback.
Press PLAY.
Each time you press the SLOW
button, the slow-motion speed
changes in the following sequence:
4
8
Notes
• The sound is muted during slow-motion playback.
• 3 speeds are available.
Resuming playback from the same location
1
Press STOP at the location where you
want to interrupt playback.
To start playback from the beginning regardless
of the location where you stopped playback
1 Press STOP twice.
The DVD video player memorizes
the location where playback is
stopped.
2
The DVD video player deletes the
memory of the location.
2 Press PLAY.
Press PLAY.
DVD
The DVD video player resumes
playback from the location where
you stopped playback.
Playback starts from the
beginning of the current title.
Playback starts from the
beginning of the disc.
• If you want to return to the beginning of a DVD video
disc, open and close the disc tray once with the
OPEN/CLOSE button before pressing the PLAY
button.
Notes
• Resuming cannot function when:
– you play a PBC-featured VIDEO CD while “PBC” is set to
“On”.
– you open the disc tray.
– you disconnect the power plug of the DVD video player.
• There may be a difference in the location where playback
resumes depending on the disc.
• Settings you changed using the on-screen displays while
the DVD video player keeps a location in the memory may
function only after the memory is cleared.
29
p25-32-4980.pmd
29
6/10/2005, 10:31 AM
Basic playback
Locating a Desired Section
TOP MENU
ENTER
Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. VIDEO CDs and audio CDs are
divided into tracks. You can quickly locate any specific title, chapter, or track.
DVD video disc
Title 1
Chapter 1
DVD
1
Title 2
Chapter 2
Chapter 1
VIDEO CD/audio CD
Chapter 2
Chapter 3
Track 1
Track 2
Track 3
Track 4
Track 5
Locating a title using the top menu
Press TOP MENU.
The top menu appears on the TV
screen.
3
Press ENTER.
Playback starts from chapter 1 of
the selected title.
e.g.
2
Press
want.
/
/
/
to select the title you
If the titles in the top menu are
assigned a number, you can directly
locate a specific title by pressing its
designated number with the number
buttons.
Notes
• The instructions above describe basic procedures which
may vary depending on the contents of the DVD video disc.
If different instructions appear on the TV screen, follow
those instructions.
• If you display the top menu during playback and press the
TOP MENU button again without selecting any title, the DVD
video player may resume playback from the point where you
first pressed the TOP MENU button (depending on the
actual DVD video disc.)
• This method of locating a title is available only on a disc that
contains a top menu.
• Instruction notes of discs may refer to the button that
displays the top menu as TITLE button.
30
p25-32-4980.pmd
30
6/10/2005, 10:31 AM
CLEAR
ENTER
PLAY
SKIP
T
Number buttons
Locating a desired section by entering the corresponding number
Press T.
Press /
or Track.
to highlight the Title/Chapter
3
Press the number buttons to enter title,
chapter or track number.
4
Press ENTER.
Basic playback
1
If you are using a VIDEO CD/audio CD, skip step 2.
Then at step 3, enter the number for the track you
want using the number buttons.
e.g.
DVD
Search
Time
Title/Chapter
Search
Time
Track
2
Press /
to locate.
to select a section you want
e.g. When you want to locate a chapter.
DVD
Playback starts from the selected
section.
Accessing chapters/tracks using number
buttons:
You can play any chapter/track you want by pressing
the corresponding number button. For the chapters/
tracks number greater than “9”, use “+10” button.
Each press increases the number by 10. Then key in
the second digit of chapter/track number.
Notes
• Pressing the CLEAR button resets the numbers. To clear the
display, press the T button several times.
• This method of locating a title is available only on a disc that
contains title numbers.
Locating a specific chapter or track
Press SKIP
or
repeatedly to access
the chapter or track number you want.
Playback starts from the selected chapter or track.
To locate succeeding chapters or
tracks.
Playback starts from the beginning of
the current chapter or track.
When you press twice in quick
successions, playback starts from the
beginning of the preceding chapter or
track.
Notes
• Some titles may not display chapter numbers.
• If you press and hold the SKIP
or
button on the
front panel during playback, the DVD video player performs
fast reverse or fast forward playback. You can vary the
speed by pressing the button repeatedly.
To locate chapters or tracks during fast reverse or fast
forward playback, first press the PLAY button to resume
or
button.
normal playback, then use the SKIP
31
p25-32-4980.pmd
31
6/10/2005, 10:31 AM
p25-32-4980.pmd
32
6/10/2005, 10:31 AM
Advanced playback
Customizing the performance of your DVD video player.
Accessing a Specific Location
Directly
Repeating a Specific Segment
Playing in a Varied Order
Playing in a Favorite Order
Zooming a Picture
Selecting the Picture Enhancement
(E.P.M.)
Selecting the Sound Enhancement
(E.A.M.)
Selecting the Camera Angle
Selecting Subtitles
Selecting a Language
On-screen Display Operation
Playing MP3/WMA Files
Viewing JPEG Files
Viewing DivX® MPEG-4 Files
p.33-38-4980.pmd
33
6/10/2005, 10:31 AM
Advanced playback
CLEAR
Accessing a Specific Location Directly
The unit stores the points that you want to watch again up to 3 points.
You can resume playback from each scene.
ENTER
PLAY
T
Entering the time counter of the desired location
1
To set and play favourite bookmark during
playback
Press T.
Press / button to highlight the
time counter.
1. Press T twice, the display of Bookmark appears, then
press ENTER to mark the desired scene.
DVD
Track
2
Press the number buttons to enter the
time.
2. Press ENTER to play the favourite bookmark.
To set other bookmarks.
e.g.
Follow step 1 and move through the menu by pressing
the or button.
Press T again to remove this display.
• The first number you entered represents hours.
• The second two numbers you entered represent
minutes.
• The third two numbers you entered represent
seconds.
• If you input a wrong number, press CLEAR.
3
To cancel the Bookmark
Follow step 1, then press CLEAR to cancel the
bookmark. Move through the menu by pressing the
button to cancel other bookmarks.
Press ENTER.
Playback starts from the
desired location.
Notes
• Some discs may not respond to this process.
• Some scenes may not be located precisely as you
specified.
• This method for accessing specific locations is available
only within the current title of the DVD video disc or within
the current track of the VIDEO CD / audio CD.
Notes
• Some discs may not work with marking operation.
• The marking is cancelled when you open the disc tray or
turn the power off.
• Some subtitles recorded around the marker may fail to
appear.
34
p.33-38-4980.pmd
34
6/10/2005, 10:31 AM
or
Repeating a Specific Segment
You can specify a desired segment and repeat it.
A-B RPT
Repeating a specific segment
1
Press A-B RPT again at the end of the
segment (point B).
To resume normal playback
Press A-B RPT until Rep off is displayed.
Notes
• Some discs may not permit A-B repeat operation.
• You cannot set the A-B repeat function for a segment that
includes multiple camera angles 41 .
• You can specify a segment only within the current title or
track (VIDEO CD).
• There may be a slight difference between point A and the
location where playback actually resumes depending on the
disc.
Advanced playback
2
Press A-B RPT at the beginning of the
segment (point A) you want to play
repeatedly.
The DVD video player automatically
returns to point A and starts repeat
playback of the selected segment
(A-B).
35
p.33-38-4980.pmd
35
6/10/2005, 10:31 AM
Advanced playback
ENTER
Playing in a Varied Order
You can play titles, chapters within a title, or tracks in a varied order.
2
1
Playing titles, chapters or tracks in a varied order
1
Press PLAY MODE.
Press / button to select desired
features and then press ENTER
button to toggle desired mode.
e.g.
Play mode
Mode
Repeat
2
Press PLAY.
Press the PLAY button, the DVD
video player starts playback in the
selected mode.
Off
Off
To resume normal playback
Press ENTER until the Off is displayed.
Off
Shuffle
Note
Some discs may not permit these operations.
Off
Off
Chapter
Track
Title
All
Chapter:
Repeats the chapters within the current title.
Title:
Repeats the current title.
Track:
Repeats the current track.
All:
Repeats the entire disc.
Off:
Resumes normal playback.
36
p.33-38-4980.pmd
36
6/10/2005, 10:31 AM
CLEAR
Playing in a Favorite Order
You can combine your favorite titles, chapters, or tracks and play them in the
order you determine. You can program up to 12 selections into the memory.
(Memory playback)
3
2
1
Setting titles, chapters, or tracks in a favorite order
1
Insert a disc and press MEMORY during
stop.
The following display appears.
Memory
1 While the display appears on the TV screen, press
/ / / to move the highlighted bar to the item
you want to change.
2 Change the selection following the instructions in
step 2.
Advanced playback
e.g.
To change the programmed selections
To cancel the programmed selections
1 While the display appears on the TV screen, press
/ / / to move the highlighted bar to the item
you want to cancel.
2 Press CLEAR.
Program
To resume normal playback from memory
playback
Memory
Press MEMORY button.
Press / / / to move the highlighted bar to Clear
All, then press the ENTER. All the input programs will
be cleared.
Press PLAY button to resume normal playback.
Program
Normal playback will start from first
location.
2
Select the items in the order you want
by pressing the number buttons.
Each time you press the / / / button, the
space is highlighted in turn. Highlight where you
want to enter, then press the corresponding
number buttons.
To select another chapter in the same title, you do
not need to select the title number.
To select tracks from a VIDEO CD/audio CD in
order, press the number buttons for the track.
3
Press / / / to move the highlighted
bar to Play Program, then press the
ENTER.
To program during playback
If you press the MEMORY button during playback, a
programming display appears.
Follow steps 2 and 3.
Notes
• Some discs may not permit memory playback operation.
• If you select repeat 36 during memory playback, the DVD
video player repeats the current memory playback.
• If you press the MEMORY or RETURN button while the
display appears on the TV screen, the display disappears.
• The programmed selections will be cleared when you turn
off the DVD video player.
The DVD video player starts
memory playback.
37
p.33-38-4980.pmd
37
6/10/2005, 10:31 AM
Advanced playback
Zooming a Picture
ZOOM
You can magnify areas within a picture.
Zooming a picture
Press ZOOM during normal, slow or still
playback.
To resume normal playback
Press ZOOM repeatedly until the
Original picture is restored.
Off
is displayed.
The centre part of the image will be
zoomed in.
e.g.
2
Each time you press the ZOOM
button, the magnification level
changes as follows:
1
2
3
Notes
• Some discs may not respond to zoom feature.
• During some scenes, the buttons may not work as
described.
• Zooming does not work on subtitles or menus included on
DVD video discs.
• The magnification level varies depending on the picture size
you select. 58
Off
Press the ZOOM button to select the
magnificant level.
Press the / / / buttons to
view a different part of the image.
You may move the image from the
centre position to UP, DOWN, LEFT
and RIGHT direction.
When you reach the edge of the
image, the display will not shift
anymore in that direction.
Off
Press the ZOOM button repeatedly
until the
Off is displayed.
38
p.33-38-4980.pmd
38
6/10/2005, 10:31 AM
Selecting the Picture Enhancement (E.P.M.*)
You can easily select a preferred picture enhancement.
*E.P.M.: Enhanced Picture Mode
2
E.P.M.
Selecting the picture enhancement
1
To exit the picture enhancement selection
Press E.P.M.
Press E.P.M. again.
The picture enhancement menu
appears.
2
Advanced playback
Note
Actual effect to picture may vary depending on the TV. Make
selection according to your preference.
Select the picture enhancement by
pressing / , then press / to make
your selections.
Each time you press the
enhancement changes.
/
button, the picture
39
p.39-47-4980.pmd
39
6/10/2005, 10:32 AM
Advanced playback
Selecting the Sound Enhancement (E.A.M.*)
You can easily switch a preferred audio enhancement.
*E.A.M.: Enhanced Audio Mode
E.A.M.
Selecting the sound enhancement
1
To exit the audio enhancement selection
Press E.A.M.
The sound enhancement will
appear:
3D On
Press the E.A.M. button again, the sound
enhancement change to OFF.
Leave the DVD video player unattended for about 5
seconds after having made a selection.
Notes
• Actual effects to sounds may vary depending on the
speaker system. Make selection according to your
preference.
• Actual effects to sounds may vary depending on the disc.
• When the DVD video player is connected to an amplifier
equipped with Dolby Surround Pro Logic, select “3D off”.
Otherwise, Dolby Surround Pro Logic may function
differently than usual.
3D*:
To obtain expansive virtual surround sound effects
from two speakers.
To use this enhancement on sounds output from
the ANALOG AUDIO OUT jacks, be sure to set
“Digital Output” to “PCM”.
* Effective in playback of a DVD video disc or a
VIDEO CD.
40
p.39-47-4980.pmd
40
6/10/2005, 10:32 AM
Selecting the Camera Angle
If the scene was recorded from multiple angles, you can easily change
the camera angle of the scene you are watching.
DVD
1
ANGLE
Changing the camera angle
Press ANGLE while playing a scene
recorded with multiple angles.
e.g.
Press the ANGLE repeatedly until the “
displayed.
1/3
” is
Notes:
• This function can only be used for discs on which
scenes shot from multiple angles have been recorded.
• If only one angle is recorded, “
1/1 ” is displayed.
Advanced playback
While playing a scene recorded with
multiple angles, press the ANGLE
button.
To resume normal playback
Number changes to show the
number of the current angle. (The
maximum number of possible angles
is 9)
2
Press ANGLE while the angle number is
displayed on the TV screen.
Press the ANGLE button repeatedly
to change the scene to the next
angle in those recorded.
• About two seconds later, playback
continues from the new angle you
selected.
• If no button is pressed within 10
seconds, playback continues
without changing the current
angle.
41
p.39-47-4980.pmd
41
6/10/2005, 10:32 AM
Advanced playback
Selecting Subtitles
You can display subtitles on the TV screen and select a subtitle language
from those included on the DVD video disc.
DVD
1
Selecting a subtitle language
Press SUBTITLE during playback.
To turn subtitles on or off
1 Press SUBTITLE during playback.
The current subtitle setting is
displayed.
2 Press SUBTITLE repeatedly until the
displayed.
e.g.
2
SUBTITLE
Press SUBTITLE while the subtitle setting
is displayed on the TV screen.
Each time you press the SUBTITLE
button, the subtitle languages
included on the DVD video disc
change.
Notes
• Some DVD video discs are set to display subtitles
automatically, and you cannot turn them off even if you set
the subtitle function to off.
• During some scenes, the subtitles may not appear
immediately after you select your desired.
• Some DVD video discs will allow you to make subtitle
selections and turn subtitles on or off only via the disc
menu.
e.g.
To turn off the subtitle setting
display, press the SUBTITLE button
repeatedly until
is displayed.
Notes
• When you turn on the DVD video player or replace a disc, the player returns to the initial default setting 61 .
When you select a subtitle language which is not included on the disc, the DVD video player plays a prior language
programmed on the disc.
• During some scenes, the subtitles may not appear immediately after you change the subtitle language.
42
p.39-47-4980.pmd
42
is
6/10/2005, 10:32 AM
Selecting a Language
You can select a preferred language and sound recording system from those
included on the DVD video disc.
AUDIO
Selecting a playback audio setting
1
2
Press AUDIO during playback.
Each time you press the AUDIO
button, the audio settings included
on the DVD video disc change.
e.g.
To turn off the audio setting display, press the
AUDIO button.
Recorded audio format number
changes sequentially. (The
maximum number of possible audio
formats is 8)
The abbreviation of the language appears instead
of the language name. Refer to the list of
languages and their abbreviations. 62
Notes
• When you turn on the DVD video player or replace a disc,
player returns to the initial default setting 61 .
If you select a sound track which is not included on the disc,
the DVD video player plays a prior sound track programmed
on the disc.
• Some discs allow you to change audio selections only via
the disc menu. If this is the case, press the MENU button
and choose the appropriate language from the selections on
the disc menu.
Advanced playback
The current audio setting is
displayed.
Press AUDIO while the audio setting is
displayed on the TV screen.
Selecting sound channels of VIDEO CDs
Press AUDIO repeatedly during
playback to hear a different audio
channel (stereo, Left or Right).
Output sound conversion table
OPTICAL or COAXIAL DIGITAL AUDIO OUT jack
Digital Output
5450 5955
• Signals of 96kHz from the
OPTICAL or COAXIAL DIGITAL
AUDIO OUT jack are depressed to
48 kHz by down sampling process
when:
– “3D On” is selected. 40
– a copyright protected disc is
played.
• Quantization bit of signals of 20 bit
or higher which is output from the
OPTICAL or COAXIAL DIGITAL
AUDIO OUT jack is 16 bit if they
are in a copyright protected disc.
43
p.39-47-4980.pmd
43
6/10/2005, 10:32 AM
Advanced playback
On-screen Display Operation
NAVI
When you turn on the on-screen display, you can view information on
operational status and access features and settings.
ENTER
On-screen display operation
Press NAVI.
The following display appears.
See the pages in
for details on the features.
e.g. When playing a DVD video disc
1/3 1/16 00:02:30
Title number
Chapter number
Elapsed time
Features
:
Title number (Track number)
Locate a title or track using the number
buttons. 31
To stop playback.
:
27
Playback starts from the beginning of the
current chapter or track. 31
Chapter number
Locate a chapter using the number buttons.
:
31
Elapsed time of the current title or track
To enter the time to locate a desired location.
To start playback.
:
26
To locate succeeding chapters or tracks.
31
34
:
To pause playback.
27
44
p.39-47-4980.pmd
44
6/10/2005, 10:32 AM
On-screen Display Operation (Continued)
DISPLAY
On-screen display operation
Time counter
DVD
Elapsed time / remaining time of the current title
VCD
Elapsed time / remaining time of the current track
CD
Viewing the operational status
1 Press DISPLAY.
The following display appears.
Advanced playback
Chapter number 31
31 Title number
Audio Setting 43
42 Subtitle Setting
Bitrate
Off
5.888Mbps
Angle Setting 41
Bit Rate
2 To turn off the display, press DISPLAY again.
Bit rate (Mbit/s)
Amount of picture, sound and subtitle data in
the DVD video disc transferred per second.
The larger the value is, the more data
processed, but this does not necessarily insure
better picture quality.
45
p.39-47-4980.pmd
45
6/10/2005, 10:32 AM
Advanced playback
2
Playing MP3/WMA Files
You can play MP3/WMA files that have been recorded on a CD-R or CD-ROM
on the DVD video player.
ENTER
PLAY
PAUSE/STEP
3
T
Playing MP3/WMA files
Preparations
• Make sure that a disc you want to play is compatible with this DVD video player.
1
Place a CD that contains MP3/WMA files
on the disc tray.
2
Press OPEN/CLOSE to load the disc.
3
47
Selecting a track (file) in the disc
1 Press T.
2 Enter the track number to select a track you want
to play.
3 Press ENTER to begin playback of the selected
track.
The current track being played is highlighted in
green.
Playback starts.
To stop playback, press STOP.
Notes
• Letters of a file/folder name overflowing the given space
are not displayed.
• You can not play in Fast reverse or Fast forward during
MP3/WMA playback.
To pause playback
Press PAUSE/STEP during playback.
To resume normal playback, press
the PLAY button.
Notes
• Some discs may not permit this operation.
• WMA tracks copy-protected cannot be played.
• The OPTICAL or COAXIAL DIGITAL AUDIO OUT jack outputs MP3/WMA sounds in the linear PCM format regardless of
the current “Digital Output” selection 59 43 .
• If you stop playback by pressing the STOP button twice and then press the PLAY button, playback will start from the first
track of the disc.
• The SKIP 31 and PLAY MODE 36 functions are also available.
46
p.39-47-4980.pmd
46
6/10/2005, 10:32 AM
Playable files
Advanced playback
MP3/WMA disc compatibility with this player is limited as follows:
• Playable discs:
CD-ROM, CD-R (650MB / 74 min. only)
CD-RW is not recommendable.
• Sampling Frequency:
44.1 kHz only
• Bit rate:
WMA: 48 kbps - 192 kbps (CBR*)
MP3: 32 kbps - 320 kbps (CBR*)
• CD physical format:
Mode 1, Mode 2 XA Form 1
• File system:
ISO9660 Level 1, 2 or Joliet
• File name:
A file name should be in alphabet and numerals only, and must incorporate “MP3” or
“WMA” extension.
e.g.“********.MP3”, “********.WMA”
• Total number of folders:
Less than 256
• Total number of files:
Less than 1000
• WMA codec version:
V7 or V8 (Stereo sound only)
* CBR = Constant Bit Rate
This DVD video player requires discs/recordings to
meet certain technical standards in order to achieve
optimal playback quality. Pre-recorded DVDs are
automatically set to these standards. There are many
different types of recordable disc formats (including CDR containing MP3/WMA files). Because this area of
technology is still evolving, Toshiba cannot guarantee
that all recordable discs will produce optimal playback
quality. The technical criteria set forth in this owner’s
manual are meant only as a guide.
Please be advised that you must obtain permission
from the applicable copyright owners to download
copyrighted content, including music files, in any
format, including the MP3 and WMA formats, prior to
the downloading thereof. Toshiba has no right to grant
and does not grant permission to download any
copyrighted content.
Microsoft, Windows Media, and the Windows
Logo are either registered trademarks or
trademarks of Microsoft Corporation in the
United States and/or other countries.
Note
When the WMA or MP3 file is out of the above specifications,
the song may be skipped or muted with counter moving.
47
p.39-47-4980.pmd
47
6/10/2005, 10:32 AM
Advanced playback
Viewing JPEG Files
You can play JPEG files that have been recorded on a CD-R or
CD-ROM on the DVD video player.
You can select a preferred view: a page of 9 thumbnail images or
a single image view.
Also, rotating, enlarging and shifting of each image can be
possible.
TOP MENU
ENTER
PLAY
PAUSE/STEP
STOP
Viewing JPEG files
Preparations
• Prepare a disc that contains JPEG files you want to view. 50
• Make your TV shape conform to the 4:3 picture size. Only 4:3 pictures can be played regardless of the function
settings via the on-screen displays of the DVD video player. If the TV is adjusted to other sizes, e.g. “WIDE,”
images will appear to be horizontally expanded. For details, refer to the owner’s manual of your TV.
1
Press OPEN/CLOSE to open the disc
tray, place a disc that contains JPEG
files.
Press OPEN/CLOSE to close the
disc tray, after completion of reading,
playback automatically starts. The
next picture will automatically display
after a few seconds.
A view appears.
(Automatic mode)
e.g.
To quit the JPEG playback, press STOP.
• Pressing the OPEN/CLOSE button to
open the disc tray can also quit the
playback.
To pause playback
Press PAUSE/STEP during playback
To resume normal playback, press
PLAY.
To change the image
To view the succeeding image, press
.
SKIP
To view the previous image, press SKIP
.
A list of folders in
the disc appears.
(Selection mode)
e.g.
To magnify image
Flower
Press ZOOM repeatedly.
0001
0006
0002
0007
0003
0004
0008
0009
0005
0010
Press / / / to select your
desired file, and then press ENTER
or PLAY button to start playback.
Press STOP to display a folder list.
Press SEARCH and enter the track
number followed by ENTER button to
quickly select your image.
Search
Track
Each time you press the ZOOM button, the
magnification level changes as follows:
1
2
3
Off
Press the / / /
buttons to view a different part of
the image. You may move the image from the centre
position to UP, DOWN, LEFT and RIGHT direction. When
you reach the edge of the image, the display will not shift
anymore in that direction.
To rotate an image
Press the ANGLE repeatedly
The image rotates by clockwise 90degree.
To resume normal playback
Press the ZOOM repeatedly until the
Off
is displayed.
• Original picture is restored when the
Off appears.
• Depending on the file size, some files
may not display the entire image.
48
p48-53-4980.pmd
48
6/10/2005, 10:32 AM
Viewing a thumbnail view
To quit the JPEG playback, press STOP.
1
Press TOP MENU in full-screen review.
• Pressing the OPEN/CLOSE button
to open the disc tray can also quit
the playback.
Press PAUSE/STEP during playback
To resume normal playback, press
PLAY.
Prev
Advanced playback
To pause playback
Next
To view the
previous 9 images.
To view the
succeeding 9 images.
Press the / / / to select
an image, press PLAY to view
one image in full-screen and
automatically images will be
displayed one by one again in a
few seconds.
Turn the page if necessary
Press / / / to highlight the PREV
or
NEXT
and ENTER to review other thumbnail
screen.
Notes
• Depending on the file size, some files may not display the entire image.
• If you press the TOP MENU in full-screen review, the DVD video player will display a menu of 9 thumbnail images.
49
p48-53-4980.pmd
49
6/10/2005, 10:32 AM
Advanced playback
JPEG files compatibility
Discs whose compatibility with this DVD video player has been confirmed by TOSHIBA are as follows.
Many of these discs, when loaded, will make the DVD video player enter the automatic mode to play a prescribed
folder in the disc. To play other folders, display a folder list and select a folder.
CANON QuickCD
FUJICOLOR CD
Kodak Picture CD
NORITSU QSS CD
JPEG disc compatibility with this DVD video player is limited as follows:
• Playable discs:
CD-ROM, CD-R (650MB / 74 min. only)
CD-RW is not recommendable.
• CD physical format:
Mode 1, Mode 2 XA Form 1
• File system:
ISO9660 Level 1, 2 or Joliet
• File name:
A file name should be in alphabet and numerals only, and must incorporate “JPG”
extension.
e.g.“********.JPG” (Do not name the file with “JPE” or “JPEG” extension.)
• Total number of folders:
Less than 256
• Total number of files:
Less than 1000
Depending on the file size, some files may not display the entire image.
Some discs may not permit this operation. Especially, the following conditions of included files will increase the disc’s
disability.
1. Pixels over 3072 x 2048 in height and/or width
2. File format except Exif
50
p48-53-4980.pmd
50
6/10/2005, 10:32 AM
Playing DivX® MPEG-4 Files
You can play DivX® and MPEG-4 files that have been
recorded on a CD-R or CD-ROM on the DVD video
player.
Playing DivX® MPEG-4 files
1
Press OPEN/CLOSE to open the disc
tray, place a disc that contains DivX® or
MPEG-4 files.
Advanced playback
Press OPEN/CLOSE to close
the disc tray, after completion of
reading, playback of first movie
automatically starts.
Press STOP to display a folder
list.
A list of folders in the
disc appears.
CD-R
[Root]
e.g.
t01_t02_kids
u03_divx51_stret
t03_t04_kids
u04_divx1_smpte
t05_aes_encrypt
u05_divx1_smpte
u01_longflight_div
5
t01_t02_kids
Press / / / to select your
desired file, and then press
ENTER or PLAY button to start
playabck.
Notes
• It is recommended you record same kind of files in a CDROM or CD-R.
• Some DivX Video-On-Demand files may require registration
code of your DVD video player, you may get the code in
Rating settings 61 .
51
p48-53-4980.pmd
51
6/10/2005, 10:32 AM
Advanced playback
Playable files
DivX® MPEG-4 disc compatibility with this player is limited as follows:
• Playable discs:
•
•
•
•
•
•
•
DivX versions:
Audio format:
Enhance video:
Frame rate:
CD physical format:
File system:
File name:
• Total number of folders:
• Total number of files”
CD-ROM, CD-R (650MB / 74 min. only)
CD-RW is not recommendable.
DivX 3.11, 4.12, 5.0, 5.1
CBR MP3, VBR MP3, Mono MP3, DivX® AC3
GMC, Qpel, Progressive B-frames
8 to 25 fps
Mode 1, Mode 2 X A Form 1
ISO9660 Level 1, 2 or Joliet
A file name should be in alphabet and numerals only, and must incorporate
“MPG” or “AVI” extension.
e.g. “ *******.MPG ”, “ *******.AVI ”
Less than 256
Less than 1000
DivX, DivX Certified, and associated logos are
trademarks of DivX, Inc. and used under license.
52
p48-53-4980.pmd
52
6/10/2005, 10:32 AM
Function setup
Customizing the Function
Settings
Table of Languages
Advanced playback
You can change the default settings to customize
performance to your preference.
53
p48-53-4980.pmd
53
6/10/2005, 10:32 AM
Function setup
2
Customizing the Function Settings
RETURN
You can change the default settings to customize performance to your
preference.
ENTER
3, 4
1, 6
Setting procedure
1
2
Press SETUP during stop.
The following on-screen display
appears.
3
Press / to select the setting you
want to change, then press ENTER.
4
Change the selection by / buttons,
by referring to the corresponding
pages, then press ENTER.
5
Repeat steps 3 and 4 to change other
settings.
6
Press SETUP.
Press / to select an option for the
setting you want to change, then press
ENTER.
(See the next page.)
Language settings
To select another option, press RETURN to go
back to step 2.
The on-screen display disappears.
Video settings
Audio settings
To return to the previous display
Press RETURN.
Rating settings
Note
To quit the procedure, press the SETUP button to turn off the
on-screen display.
54
p54-63-4980SU.pmd
54
6/10/2005, 10:32 AM
Setting
Language
Video
Rating
OSD Menu
Page
To select a preferred language for on-screen
display.
56
Subtitle
DVD
To select a preferred language for subtitles.
56
Audio
DVD
To select a preferred language for the sound
track.
57
DVD Menu
DVD
To select a preferred language for disc menus.
57
DivX
DVD
To select a preferred language for your DivX
video disc.
57
TV Shape
DVD
To select a picture size according to aspect
ratio of your TV.
58
Video Output
To select whether you send Composite or
Component signals to the connected TV.
58
Digital Output
To select an output sound format corresponding 59
to your system connection.
Password
DVD
To create a personal security code.
59
Rating
DVD
To turn the parental lock function on or off.
59
FL. Dimmer
To adjust the DVD display and the blue DVD
door brightness.
60
Default
To return the initial settings such as Language, 61
Video, Audio and etc. to the factory default.
DivX registration
DVD
To get your DVD Video Player DivX registration
code.
Function setup
Audio
Details
61
55
p54-63-4980SU.pmd
55
6/10/2005, 10:32 AM
Function setup
Customizing the Function Settings (continued)
Setting details
Subtitle
Language
English:
Français:
Español:
Auto:
Off:
OSD Menu
English: To view on-screen displays in english.
Français: To view on-screen displays in french.
Español: To view on-screen displays in spanish.
DVD
To display subtitles in english.
To display subtitles in french.
To display subtitles in spanish.
To display subtitles in different
languages other than you selected.
To disable subtitles.
1) Press ENTER.
2) Press / to select the Subtitle.
3) Press ENTER button, then the /
and change the Language.
4) Press ENTER.
5) Press RETURN.
to shift
1) Press ENTER.
2) Press / to select the OSD Menu.
3) Press ENTER button, then the / to shift
and change the Language.
4) Press ENTER.
5) Press RETURN.
Note
Some DVD video discs may not include your preselected language. In this case, the DVD video player
automatically displays disc menus consistent with the
disc’s initial language setting.
Notes
• Some DVD video discs may be set to display subtitles
in a different language other than you selected. A prior
subtitle language may be programmed on the disc.
• Some DVD video discs allow you to change subtitle
selections only via the disc menu. If this is the case,
press the MENU button and choose the appropriate
subtitle language from the selection on the disc menu.
56
p54-63-4980SU.pmd
56
6/10/2005, 10:32 AM
Audio
DVD
DivX
English:
Français:
Español:
To play sound tracks in english.
To play sound tracks in french.
To play sound tracks in spanish.
If your DivX files include a subtitle file, then you may
select below 6 subtitles:
1) Press ENTER.
2) Press / to select the Audio.
3) Press ENTER button, then the /
and change the Language.
4) Press ENTER.
5) Press RETURN.
to shift
DVD
Western Europe
Central Europe
Slavonic Cyrillic
Greek
Turkish
Hebrew
Note
Some DVD video discs may not be played in a different
language than you selected. A prior language may be
programmed on the disc.
DVD Menu
English:
Français:
Español:
DivX
Function setup
1) Press ENTER.
2) Press / to select the DivX.
3) Press ENTER button again until your preferred
subtitle is displayed.
4) Press RETURN.
WesternEurope
DVD
To display DVD menus in english.
To display DVD menus in french.
To display DVD menus in spanish.
1) Press ENTER.
2) Press / to select the DVD menu.
3) Press ENTER button, then the / to shift
and change the Language.
4) Press ENTER.
5) Press RETURN.
Notes
• If your DivX files do not include the subtitle file, you
cannot use this selection.
• Supported subtitle file formats:
.srt, .sub, .txt, .smi, .ssa, .ass, .psb.
Note
Some DVD video discs may not include your preselected language. In this case, the DVD video player
automatically displays disc menus consistent with the
disc’s initial language setting.
57
p54-63-4980SU.pmd
57
6/10/2005, 10:32 AM
Function setup
Customizing the Function Settings (continued)
Setting details
Video Output
Video
TV Shape
1)
2)
3)
4)
Press /
to select the Video.
Press ENTER.
Press
/ to select the Video Output.
Press ENTER button, then press / to select
the output mode.
5) Press ENTER.
6) Press RETURN.
DVD
1) Press /
to select the Video.
2) Press ENTER.
3) Press ENTER button, then press the
shift and change the TV type
4) Press ENTER.
5) Press RETURN.
Composite: Select if you connect the DVD to TV via
composite video (yellow) input or
S-VIDEO input.
/
to
4:3 Pan Scan:
Select when a standard 4:3 TV is
connected.
Displays pictures cropped to fill
your TV screen. Either or both
sides of the picture are cut off.
4:3 Letter Box:
Select when a standard 4:3 TV is
connected.
Displays theatrical images with
masking bars above and below the
picture.
16:9 Wide:
Select when a 16:9 TV is
connected.
Component: Corresponding to your TV which has a
component video inputs. Progressive
mode can only be on when Component
is selected.
Note
At component mode, there is no S-VIDEO output.
Notes
• The displayable picture size is preset on the DVD
video disc. Therefore, the playback picture of some
DVD video discs may not conform to the picture size
you select.
• When you play DVD video discs recorded in the 4:3
picture size only, the playback picture always appears
in the 4:3 picture size regardless of the TV shape
setting.
• If you select “16:9 Wide” and you own a 4:3 TV set, the
DVD playback picture will be horizontally distorted
during playback. Images will appear to be horizontally
compressed. Always be sure that your TV shape
conforms to the actual TV in use.
58
p54-63-4980SU.pmd
58
6/10/2005, 10:32 AM
Audio
Rating
Digital Output
Password / Rating
Selected the output sound format corresponding to
your system connection.
DVD discs equipped with the password function are
rated according to their content. The contents
allowed by a parental lock level and the way a DVD
disc can be controlled may vary from disc to disc.
PCM:
Select when connected to a 2 channel
digital stereo amplifier.
The DVD video player outputs sounds in the
PCM 2 channel format when you play a
DVD video disc recorded on the Dolby
Digital, MPEG1 OR MPEG2 recording
system.
Bitstream:
Disc audio raw data will be output.
Note
When you make a connection to a TV, or Dolby Surround
Pro Logic or stereo system via the analog audio jacks,
select “PCM” or “Bitstream”.
Function setup
1) Press /
to select Audio.
2) Press ENTER.
3) Press ENTER button, then press / to shift
and change the output sound format.
4) Press ENTER.
5) Press RETURN.
DVD
For example, if the disc allowed, you could edit out
violent scenes unsuitable for children and replace
them with more suitable scenes, or you could lock
out playback of the disc altogether.
• DVD video discs may or may not respond to the
parental lock settings. This is not a defect in the
DVD video player. Make sure this function works
with your DVD video discs.
1) Press /
to select the Rating.
2) Press ENTER.
3) Press / to select Rating and then press
ENTER repeatedly to set the parental lock
level.
4) Press to the Password and enter your 4digits security code, then press ENTER button.
5) Press RETURN.
Password
----
Password
----
Rating
8. Adult
Rating
8. Adult
FL. Dimmer
Normal
FL. Dimmer
Normal
Default
No
Default
No
DivX registration
Display
DivX registration
Display
Notes
• If you make a mistake before pressing ENTER button,
press CLEAR button and enter your 4-digit security
code again.
• You cannot play DVD discs rated higher than the level
you selected unless you cancel the parental lock
function.
(continued)
59
p54-63-4980SU.pmd
59
6/10/2005, 10:32 AM
Function setup
Customizing the Function Settings (continued)
Setting details
(continued)
FL. Dimmer
The parental lock level is equivalent to the following
ratings:
Level 1: Kid Safe
DVD display can be adjusted, do the following to set
to the brightness you prefer:
1)
2)
3)
4)
5)
Level 2: G
Level 3: PG
Level 4: PG-13
Level 5: PG-R
Press / to select Rating.
Press ENTER.
Press / to select FL. Dimmer.
Press ENTER.
Press / to select Dim, then press ENTER
button.
Level 6: R
Level 7: NC-17
Level 8: Adult
Indicates Parental lock is not active.
The Parental lock is active.
If you forget the password, you can erase
your current password by pressing number
button 8 on the remote four times, then press
ENTER button to confirm the setting.
PASSWORD: 8888
Password
----
Rating
8. Adult
FL. Dimmer
Normal
Default
No
Dim
DivX registration
Display
Off
Normal
Note
Regardless the current setting, the DVD video player
will return to Normal brightness the next time when you
turn it on.
60
p54-63-4980SU.pmd
60
6/10/2005, 10:32 AM
Default
DivX registration
If you want to return the inital language setting such
as Language, Video, Audio and etc. to the factory
default, do the following:
Some DivX Video-On-Demand files required
registration code, please get the code of your DVD
video player as follow:
1)
2)
3)
4)
5)
1)
2)
3)
4)
5)
6)
Press / to select Rating.
Press ENTER.
Press / to select the Default.
Press ENTER.
Press / to select Yes, then press ENTER
button.
DVD
Press / to select Rating.
Press ENTER.
Press / to select the DivX registration.
Press ENTER.
Your registration code will be shown.
Press RETURN.
Function setup
Password
----
Rating
8. Adult
FL. Dimmer
Normal
Default
No
No
DivX registration
Display
Yes
Note
When you reset the DVD video player to the factory
default, the DVD video player will take 3-5 seconds to
reset.
Note
This registration code is for DivX Video-On-Demand
only, do not apply this code for other applications or
websites.
61
p54-63-4980SU.pmd
61
6/10/2005, 10:32 AM
Function setup
Table of Languages
Table of languages and their abbreviations
Abbreviation
–––
CHI (ZH)
DUT (NL)
ENG (EN)
FRE (FR)
GER (DE)
ITA (IT)
JPN (JA)
KOR (KO)
MAY (MS)
SPA (ES)
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DA
DZ
EL
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
GL
Language
Abbreviation
No alternate
language
Chinese
Dutch
English
French
German
Italian
Japanese
Korean
Malay
Spanish
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Belorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Irish
Scottish Gaelic
Galician
GN
GU
HA
HI
HR
HU
HY
IA
IE
IK
IN
IS
IW
JI
JW
KA
KK
KL
KM
KN
KS
KU
KY
LA
LN
LO
LT
LV
MG
MI
MK
ML
MN
MO
MR
MT
MY
NA
NE
NO
OC
OM
OR
PA
PL
PS
Language
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Hebrew
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laotian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Maltese
Burmese
Nauru
Nepali
Norwegian
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Abbreviation
PT
QU
RM
RN
RO
RU
RW
SA
SD
SG
SH
SI
SK
SL
SM
SN
SO
SQ
SR
SS
ST
SU
SV
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Language
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sango
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tongan
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
Xhosa
Yoruba
Zulu
62
p54-63-4980SU.pmd
62
6/10/2005, 10:32 AM
Others
Before Calling Service Personnel
Specifications
United States Warranty
p54-63-4980SU.pmd
63
6/10/2005, 10:32 AM
Others
Before Calling Service Personnel
Check the following guide for the possible cause of a problem before contacting service.
Symptoms and correction
Symptom
Cause
Correction
No power.
• The power plug is disconnected.
• Connect the power plug securely into the
wall outlet.
The DVD video player turned off
by itself.
• The automatic power off function turned the
unit off.
• Press the PLAY button.
27
No picture or abnormal colour
(pinkish, greenish, etc.).
• The TV is not set to receive DVD signal
output.
• Select the appropriate video input mode on
the TV so the picture from the DVD video
player appears on the TV screen.
26
• The video cable is not connected securely.
• Connect the video cable securely into the
appropriate jacks.
• Mismatch setting between TV and this unit.
• Select the correct Video Output setting.
• Wrong connection.
• Check the connection.
Scrolling, jumping or B/W
picture
• Incompatible TV system.
• Select the correct TV system
No sound.
• The equipment connected with the audio
cable is not set to receive DVD signal output.
• Select the correct input mode of the audio
receiver so you can listen to the sound from
the DVD video player.
• The audio cable is not connected securely.
• Connect the audio cable securely into the
appropriate jacks.
18-24
• The audio receiver or TV is turned off.
• Turn on the equipment connected with the
audio cable.
26
• The setting of output sound format is
incorrect.
• Select the proper audio setting.
The playback picture has
occasional distortion.
• The disc is dirty.
• Eject the disc and clean it.
9
• It is in fast forward or fast reverse playback.
• Sometimes a small amount of picture
distortion may appear. This is not a
malfunction.
-
Brightness is unstable or noises
are present in the playback
pictures.
• The effect of copy protection.
• Connect the DVD video player directly to the
TV. Avoid connecting the DVD video player
to a VCR or TV/VCR combination.
18
The DVD video player does not
start playback.
• No disc is inserted.
• Insert a disc.
26
• An unplayable disc is inserted.
• Insert a playable disc. (Check the disc type
and color system.)
12
• The disc is placed upside down.
• Place the disc with the playback side down.
26
• The disc is not placed within the guide.
• Place the disc correctly inside the guide on
the disc tray.
26
• The disc is dirty.
• Clean the disc.
• The parental lock function is set.
• Cancel the parental lock function or change
the parental lock level.
Playback does not follow the
course of the disc’s program.
• It is in the mode of repeat playback, memory
playback, etc.
• These operations may prevent a proper
progress of the contents.
Buttons do not work.
• Power supply fluctuations or other
abnormalities such as static electricity may
interrupt correct operations.
• Press and hold the ON/STANDBY button on
the front panel for more than about 3
seconds. The DVD video player turns off.
Press the button again to turn it on. If the
buttons still do not work, disconnect the
power plug and insert it into the wall outlet
again.
• The remote control is not pointed at the
remote sensor of the DVD video player.
• Point the remote control at the remote
sensor of the DVD video player.
• The remote control is too far from the DVD
video player.
• Operate the remote control within about 7 m.
• The batteries in the remote control are
exhausted.
• Replace the batteries with new ones.
The remote control does not
work properly.
Page
64
18,19,20
58
18,19,20
54,58
26
43,54,59
9
54,59
-
-
15
15
64
p64-68-4980SU.pmd
18,19,20
6/10/2005, 10:32 AM
15
Specifications
DVD video player / outputs / supplied accessories
DVD Video Player
Power supply
120 V AC, 60 Hz
Power consumption
14 W
Mass
1.6 kg
External dimensions
430 x 42 x 200 mm (W/H/D)
Signal system
Standard NTSC
Laser
Semiconductor laser, wavelength 650/780 nm
Frequency range
DVD linear sound :
Signal-to-noise ratio
More than 100 dB
Audio dynamic range
More than 93 dB
48 kHz sampling 4 Hz to 22 kHz
96 kHz sampling 4 Hz to 44 kHz
Less than 0.005 %
Wow and flutter
Below measurable level (less than ±0.001 % (W.PEAK))
Operating conditions
Temperature: 5 °C to 35 °C, Operation status: Horizontal
Others
Harmonic distortion
Outputs
Video output
1.0 V (p-p), 75 Ω, negative sync., pin jack x 1
S video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., Mini DIN 4-pin x 1
(C) 0.286 V (p-p), 75 Ω
Component video output
(Y) 1.0 V (p-p), 75 Ω, negative sync., pin jack x 1
(PB)/(PR) 0.7 V (p-p), 75 Ω, pin jack x 2
Audio output (COAXIAL DIGITAL)
0.5V (p-p), 75 Ω, pin jack x 1
Audio output (OPTICAL DIGITAL)
Optical connector x 1
Audio output (ANALOG)
2.0 V (rms), 680 Ω, pin jacks (L, R) x 1
HDMI output
19 pin
Supplied Accessories
Audio/video cable .................................................. 1
Remote control (SE-R0168) .................................. 1
Batteries (AAA) ...................................................... 2
• This model complies with the above specifications.
• Designs and specifications are subject to change without notice.
• This model may not be compatible with features and/or specifications that may be added in the future.
65
p64-68-4980SU.pmd
65
6/10/2005, 10:32 AM
Others
Limited United States Warranty
Digital Audio Video (“DAV”) Product - Exchange Warranty
Toshiba America Consumer Products, L.L.C. (“TACP”) makes the following limited warranties to original consumers in
the United States. THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY
PERSON RECEIVING THIS DAV PRODUCT AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO
NO OTHER PURCHASER OR TRANSFEREE.
DAV PRODUCTS PURCHASED IN THE U.S.A. AND USED ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING,
WITHOUT LIMITATION, CANADA AND MEXICO, ARE NOT COVERED BY THESE WARRANTIES.
DAV PRODUCTS PURCHASED ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT LIMITATION,
CANADA AND MEXICO, AND USED IN THE U.S.A., ARE NOT COVERED BY THESE WARRANTIES.
Limited Warranty
TACP warrants this DAV Product and its parts against
defects in materials or workmanship for a period of
ninety (90) days after the date of original retail purchase.
DURING THIS PERIOD, TACP WILL EXCHANGE A
DEFECTIVE DAV PRODUCT WITH A NEW OR
REFURBISHED DAV PRODUCT WITHOUT CHARGE
TO YOU. DURING THE PERIOD THAT COMMENCES
ON THE DATE THAT IS NINETY ONE (91) DAYS
AFTER THE DATE OF ORIGINAL RETAIL PURCHASE
AND ENDS ON THE DATE THAT IS THREE HUNDRED
SIXTY FIVE (365) DAYS AFTER THE DATE OF
ORIGINAL RETAIL PURCHASE, TACP WILL
EXCHANGE A DEFECTIVE DAV PRODUCT WITH A
NEW OR REFURBISHED DAV PRODUCT FOR A FEE.
Your Responsibility
Rental Units
The warranty for DAV Product rental units begins on the
date of the first rental or thirty (30) days after the date of
shipment to the rental firm, whichever comes first.
(4) Labor service charges for set installation, setup,
adjustment of customer controls, and installation or
repair of antenna systems are not covered by this
warranty. Reception problems caused by inadequate
antenna systems are your responsibility.
Commercial Units
DAV Products sold and used for commercial purposes
have a limited warranty for all parts and labor, which
warranty begins on the date of original retail purchase
and ends on the date that is ninety (90) days thereafter.
Owner’s Manual and Product Registration Card
Read this owner’s manual thoroughly before operating
this DAV Product.
Complete and mail the enclosed product registration
card or register your DAV Product on-line at
www.tacp.toshiba.com/service as soon as possible. By
registering your DAV Product you will enable TACP to
bring you new products specifically designed to meet
your needs and help us to contact you in the unlikely
event a safety notification is required under the U.S.
Consumer Product Safety Act. Failure to complete and
return the product registration card does not diminish
your warranty rights.
THE ABOVE WARRANTIES ARE SUBJECT TO THE
FOLLOWING CONDITIONS:
(1) You must retain your bill of sale or provide other proof
of purchase.
(2) All warranty servicing of this DAV Product must be
made pursuant to the TACP DAV Product Warranty
Exchange Program.
(3) The warranties from TACP are effective only if the DAV
Product is purchased and operated in the Continental
U.S.A. or Puerto Rico.
(5) Warranties extend only to defects in materials or
workmanship as limited above, and do not extend to
any DAV Product or parts that have been lost or
discarded by you or to damage to the DAV Product or
parts caused by fires, misuse, accident, Acts of God
(such as lightning or fluctuations in electric power),
improper installation, improper maintenance, or use in
violation of instructions furnished by TACP; use or
malfunction through simultaneous use of this DAV
Product and connected equipment; or to units that
have been modified or had the serial number removed,
altered, defaced, or rendered illegible.
66
p64-68-4980SU.pmd
66
6/10/2005, 10:32 AM
How to Obtain Warranty Services
If, after following all of the operating instructions in this
manual and checking the section “Troubleshooting,” you
find that service is needed:
(1) For instructions on how to obtain warranty service for
your DAV Product under the TACP DAV Product
Warranty Exchange Program, contact TACP’s
Consumer Solutions Center toll free at
1-800-631-3811.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH MAY VARY FROM STATE TO STATE IN THE
U.S.A. SOME STATES OF THE U.S.A. DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, WHEN AN ACTION MAY BE BROUGHT, OR THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE
PROVISIONS MAY NOT APPLY TO YOU UNDER SUCH
CIRCUMSTANCES.
(2) You must include the original bill of sale (or a copy of
the original bill of sale) or other proof of purchase
along with the entire DAV Product when sending the
DAV Product to the TACP Warranty Exchange Center
specified by TACP’s Consumer Solutions Center. You
are responsible for all inbound transportation and
insurance charges for the DAV Product to the TACP
Warranty Exchange Center.
For additional information, visit TACP’s website:
www.tacp.toshiba.com
Others
ALL WARRANTIES IMPLIED BY THE LAW OF ANY
STATE OF THE U.S.A., INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE EXPRESSLY
LIMITED TO THE DURATION OF THE LIMITED
WARRANTIES SET FORTH ABOVE. WITH THE
EXCEPTION OF ANY WARRANTIES IMPLIED BY THE
LAW OF ANY STATE OF THE U.S.A. AS HEREBY
LIMITED, THE FOREGOING WARRANTY IS EXCLUSIVE
AND IN LIEU OF ALL OTHER WARRANTIES,
GUARANTEES, AGREEMENTS, AND SIMILAR
OBLIGATIONS OF TACP WITH RESPECT TO THE
REPAIR OR REPLACEMENT OF ANY PARTS.
IN NO EVENT SHALL TACP BE LIABLE FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, LOST PROFITS,
BUSINESS INTERRUPTION, OR MODIFICATION OR
ERASURE OF RECORDED DATA CAUSED BY USE,
MISUSE OR INABILITY TO USE THIS DAV PRODUCT).
No person, agent, distributor, dealer, or company is
authorized to change, modify, or extend the terms of these
warranties in any manner whatsoever. The time within
which an action must be commenced to enforce any
obligation of TACP arising under the warranty or under any
statute or law of the United States or any state thereof is
hereby limited to ninety (90) days from the date you
discover, or should have discovered, the defect. This
limitation does not apply to implied warranties arising
under state law.
67
p64-68-4980SU.pmd
67
6/10/2005, 10:32 AM
Printed in China
811-498091-040
p64-68-4980SU.pmd
68
6/10/2005, 10:32 AM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement