Installation Instructions IN
Installation
“Allen-Bradley
1336 IMPACT
IP 20 (NEMA Type 1)
Enclosure Kit Installation
Cat. Nos. 1336E-AA2-AA7
1336E-AE2-AE7
This publication will guide you through installation of an IP 20
(NEMA Type 1) Enclosure Kit (1336E-AAx), or an IP 20
(NEMA Type 1) EMC Enclosure Kit (1336-AEx). For additional
information, refer to the 1336 IMPACT User Manual —
1336 IMPACT-5.0.
Discharge) sensitive parts and assemblies. Static control
precautions are required when installing, testing, servicing
or repairing this assembly. Component damage may result
if ESD control precautions are not followed. If you are not
familiar with static control procedures, reference AB
publication 8000-4.5.2, "Guarding Against Electrostatic
Damage" or any other applicable ESD protection handbook.
A ATTENTION: This drive contains ESD (Electrostatic
power to the drive has been removed before proceeding with
the following procedure. In addition, verify that the DC bus
has discharged by measuring across the "+DC" and "-DC"
terminals of TB1 with a voltmeter. The voltage should be
0.0V DC.
A ATTENTION: To avoid a shock hazard, assure that all
on enclosed IP 20 (NEMA Type 1) drives, the blank cover
plate (option HAB) must be installed to close the opening in
the front cover of the enclosure. Failure to install a blank
cover plate to close the enclosures front cover opening allows
access to live electrical parts which may result in personal
injury and/or equipment damage.
When a drive mounted HIM is supplied with enclosed IP 20
drives but has been removed from its mounting cradle for
remote operation, the blank cover plate must be installed in
place of the HIM.
A ATTENTION: When a drive mounted HIM is not supplied
1336 IMPACT-5.4 February 1997
2 1336 IMPACT NEMA Type 1 Enclosure Kits
1336 IMPACT-5.4 February 1997
Access to the top, bottom, and side of the drive chassis is required to
assemble the kit. If the open chassis drive is already installed, remove
& lock-out all power to the drive, then label & disconnect all wiring.
External wiring will have to be rerouted through enclosure knockouts
once the kit has been installed.
Figure 1 —
Enclosure Kits 1336E — AA2 & AA3
1. Mount the top, bottom & side plates to the chassis using the supplied
screws. Tighten all screws to 1.7N-m (151b.-in.).
2. Install the front cover by sliding it up then down to engage the slots
into the angled tabs. Swing the cover bottom in and secure it with
the captive screw. Tighten to 0.7N-m (6 Ib.-in.).
Figure 2 —
EMC Enclosure Kits 1336E — AE2 & AE3
1. Mount the bottom plate to the chassis using the supplied screws.
2. Slide the enclosure assembly over the chassis as shown.
3. Fasten the assembly to the chassis using the supplied screws.
Tighten all screws to 1.7N-m (151b.-in.).
Figure 3 —
Enclosure Kits 1336E — AA4 & AAS
1. Slide the side plates over the chassis tabs as shown.
2. Attach the top & bottom plates to the side plates by sliding the tabs
into the corresponding slots. Fasten the assembly to the chassis
using the supplied screws. Tighten all screws to 1.5N-m (131b.-in.).
3. Install the front cover by sliding it up then down to engage the slots
in the angled tabs. Swing the cover bottom in and secure it with the
captive screw. Tighten to 0.7N-m (6 1b.-in.).
Figure 4 —
EMC Enclosure Kits 1336E — AE4 & AES
1. Mount the bottom plate to the chassis using the supplied screws.
2. Slide the enclosure assembly over the chassis as shown.
3. Fasten the assembly to the chassis using the supplied screws.
Tighten all screws to 1.5N-m (131b.-in.).
1336 IMPACT NEMA Type 1 Enclosure Kits
)
Figure 2
® = = = = = = {= = = = = = = === не
/
`
`
x
`
`
ъ
`
\
>
`
`
/
%
\ N
\ v
\
>
Figure 1
AE2 & AE3
EMC Enclosure Kits 1336E -
AA2 & AA3
Enclosure Kits 1336E —
Figure 3
EMC Enclosure Kits 1336E-AE4 & AES
Enclosure Kits 1336E — AA4 & AAS
1336 IMPACT-5.4 February 1997
Figure 5 —
Enclosure Kits 1336E — AA6 & AA7
EMC Enclosure Kits 1336E — AEG & AE7
1. Slide the side plates over the chassis tabs as shown.
2. Attach the top & bottom plates to the side plates by
sliding the tabs into the corresponding slots. Fasten
— the assembly to the chassis using the supplied
IQ г screws. Tighten all screws to 1.5N-m (131b.-in.).
+ | Queso | 3. Install the door on the side plate hinge pins.
Q S
| 4. For EMC Enclosure Kits, locate the supplied
jumper wire and fasten one end to the chassis
o | ground stud. The other end must be fastened to the
x stud located in the lower corner of the door.
\ 1335 nme
far
W/o Door Grounding Jumper
N Jumper must be Installed
inside Enclosure between
Q Enclosure Door
(Grounding Stud) and
Chassis Grounding Stud.
O S
— | ©
0 С >
teca D
J
Figure 5
Enclosure Kits 1336E-AA6 & AA7
EMC Enclosure Kits 1336E-AE6 & AE7
oN ku ; Allen-Bradley, a Rockwell Automation Business, has been helping its customers improve
2 Roc ell Automation productivity and quality for more than 90 years. We design, manufacture and support a broad
Allen-Bradley range of automation products worldwide. They include logic processors, power and motion control
devices, operator interfaces, sensors and a variety of software. Rockwell is one of the world's
leading technology companies.
Worldwide representation.
Argentina * Australia * Austria * Bahrain * Belgium « Bolivia * Brazil * Bulgaria * Canada * Chile * China, PRC * Columbia e Costa Rica * Croatia * Cyprus * Czech Republic e Denmark
Ecuador * Egypt * El Salvador * Finland * France * Germany * Ghana * Greece * Guatemala * Honduras * Hong Kong * Hungary + Iceland * India * Indonesia * Iran * Ireland * Israel * Italy
Jamaica * Japan * Jordan * Korea * Kuwait * Lebanon * Malaysia * Mexico e Netherlands * New Zealand + Norway * Pakistan * Peru + Philippines * Poland * Portugal
Puerto Rico + Qatar * Romania * Russia—IS e Saudi Arabia * Singapore * Slovakia * Slovenia * South Africa, Republic * Spain * Sweden * Switzerland * Taiwan * Thailand
Turkey * United Arab Emirates * United Kingdom e United States * Uruguay * Venezuela
Allen-Bradley Headquarters, 1201 South Second Street, Milwaukee, WI 53204 USA, Tel: (1) 414 382-2000 Fax: (1) 414 382-4444
Publication 1336 IMPACT-5.4 — February 1997 P/N 74103-878-01 (A)
Copyright 1997 Allen-Bradley Company, Inc. Printed in USA
">