to the User Manual for the FS-01 safe

to the User Manual for the FS-01 safe
Berman Safes FS Series
Thank you for choosing a Berman Safe - FS Series. Before operating your new safe, please read the user manual to ensure optimum performance.
1. FIRST TIME OPENING THE SAFE 3. PROGRAMMING YOUR FINGER
a. Lift the bottom of the square
plate (plate P on Diagram 1 The safe can be opened by any
shown below - next to the finger that has previously been
fingerprint sensor), then the setup. To register your finger:
top, to remove plate.
a. With the door open, press the
b. Insert the key into the lock
green button located on the
and turn clockwise to open
top of the door. The front light
the door.
will turn yellow and the
fingerprint reader is ready to
capture.
b. Place your finger on the
fingerprint reader within 5
seconds. Please register the
same finger three times. When
the front light turns green,
your fingerprint has been
successfully registered.
2. INSTALLING THE BATTERIES
If the light turns red and you
hear 3 beeps, the registration
The safe requires 4 AA (1.5V/LR6)
failed. Please try again.
batteries (included). Remove the
battery cover (located on the inside IMPORTANT:
• To enhance the fingerprint
of the door) and install the batteries
into the compartment. Make sure
identification
rate,
we
that the batteries are fitted in the
recommend the same finger is
right position to match the polarity.
programmed 3 or more times,
Close the battery compartment.
from different positions, as
shown in Diagram 2 of the user
Use of alkaline batteries is recommended.
manual.
•
•
•
•
•
We also suggest that you NOTE:
The safe can record up to 100
register 2 fingers for each hand
fingerprints.
programmed.
To avoid fingerprint reading
failure,
we
recommend
cleaning your finger with a dry 4. USING THE SAFE
cloth before placing it on the
reader. Also, keep the reader To open the safe:
clean from grease
and
humidity.
a. Press the button located on
Always keep your finger steady
the right side of the
and press your fingertip when
fingerprint reader. The yellow
scanning.
light will turn on, indicating
The little finger is not
that the reader is ready to
recommended to be used for
operate.
fingerprint identification.
b. Place your registered fingertip
Avoid bright lighting exposure
on the fingerprint reader
on the top of the fingerprint
within 5 seconds. If the
reader.
fingerprint is valid, the light
will turn green and the door
will open automatically. If the
authentication fails, the light
will turn red and you will hear
3 beeps.
To close the safe:
Close the door and press the button
to the right side of the fingerprint
reader. The door will lock itself
automatically.
Berman Safes FS Series
IMPORTANT:
The safe can only be operated
using the same locking system.
For example, if you opened the
safe electronically, you need to
lock it the same way. And if you
opened the safe with the key, it
should be locked with the key as
well.
5. DELETING ALL FINGERPRINT
RECORDS
7. OVERRIDE INSTRUCTION TO
OPEN THE SAFE
For your convenience, we have
engineered a manual override
system to open the safe. In case of
emergency, remove the plate P
(Diagram 1) as explained on Step 1,
insert the key and turn clockwise.
This will manually open the safe.
CAUTION:
Do not keep the keys inside the safe.
While the safe door is open, press
the red button located on the top of
8. INSTALLING THE SAFE
the door 3 times in a row. If the light
on the front turns green, all the
To help reduce the risk of theft, we
fingerprint records have been
suggest that your safe is securely
deleted.
fixed to a wall or a floor. Please use
the provided bolts to fix the safe
horizontally.
6. REPLACING THE BATTERIES
9. CARE AND MAINTENANCE
The safe requires 4 AA (1.5V/LR6) For your convenience, the safe has
Keep the safe between 40°F and
batteries.
pre-drilled fixing holes at both the 110°F. Avoid using in damp
bottom and at the back. Please fix conditions.
Open the safe, remove the battery the safe according to the steps on
cover and replace the batteries Diagram 3.
inside.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement