Field Guide

Field Guide
2.1.3 Installing the Rubber Cover on CompM3 and ML3
NOTE: The Rubber Cover (10) shall be mounted to the CompM3 and ML3
after the sight has been installed in the ring.
a.Remove the lens covers (front and rear).
b.Put the front part of the sight into the lower opening of the Rubber Cover
(10) and pull it backwards over the rear part of the sight. Be careful not to
pull too hard and far, the Rubber cover (10) could be destroyed (fig. 4) .
c.Re-install the lens covers (8) and (9).
d.When removing the Rubber cover (10) from the sight, do the opposite:
Start by gripping the lower the rear part of the Rubber cover (10) and pull
it upwards and forward, off the sight.
2.2 OPERATING PROCEDURES
2.2.1 Zeroing
Aimpoint’s sights are delivered in a centered position. Normally this means
that only small adjustments are necessary, providing that the base(s) are
properly aligned.
CAUTION: Do not continue to adjust windage and elevation mechanisms if
you encounter resistance.
The elevation Adjustment screw is located on top of the sight, while the
windage screw is located on the right or left side, depending on how the
sight has been mounted on the weapon. Aimpoint sights can be installed to
support either right hand (fig. 2) or left hand (fig. 3) shooters.
a.Open Front and Rear Lens covers (9) and (8).
b.Turn the Rotary switch (4) clockwise until the red dot has a sufficient
intensity to contrast against target.
c.Insert adjustment tool (coin, screwdriver, knife) or cartridge casing in
Adjustment screw slot (7) and turn as follows:
NOTE: Each click of the Adjustment screws (7) corresponds to a 13 mm
movement of the point of impact at 80 meters, (4 mm at 25 meters, 16
mm at 100 meters and 32 mm at 200 meters or 1/4” at 50 yds, 1/2” at 100
yds and 1” at 200 yds)
• To move the point of impact to the right, turn windage adjustment screw
counter clockwise (clockwise if screw located on left side).
• To move the point of impact to the left, turn windage adjustment screw
clockwise (counter clockwise if screw located on left side).
• To move the point of impact up, turn elevation adjustment screw counter
clockwise.
• To move the point of impact down, turn elevation adjustment screw
clockwise.
d.Confirm zeroing by firing at least three shots at a zeroing target. Check
impact points on zeroing target to confirm accuracy and repeat above
procedure if required.
e.After initial firing, ensure that the mount and sight are secure.
f. Turn Rotary switch (4) to OFF position (counter clockwise).
g.Close front and rear Lens cover (9) and (8).
CHAPTER III – OPERATION UNDER EXTREME CONDITIONS
CHAPTER IV – TROUBLE SHOOTING PROCEDURES
a.Extreme heat (moist or dry): No special procedures required.
b.Extreme cold: Extreme cold might shorten battery life. Keep spare batteries
in your inner pockets to keep them warm.
c.Salt air: No special procedures required.
d.Sea spray, water, mud and snow: Ensure that the Battery cap (2) and the
two Adjustment screw caps (5) are tight before exposing the sight to sea
spray, mud, snow or before submersing the sight into water. Hand tighten
only. Keep Lens covers (8) and (9) closed when the sight is not being
used. Clean lenses with lens paper/cloth and wipe the sight dry as soon as
possible after exposure to water, sea spray, mud or snow.
e.Dust storms and sand storms: Keep Lens covers (8) and (9) closed when
the sight is not being used.
f. High altitudes: No special procedures required.
CAUTION: The lenses shall never be cleaned with fingers but with lens
paper/cloth. If lens paper/cloth is not available:
4.1 RED DOT DOES NOT APPEAR
–– To clear away debris (sand, grass etc): blow away the dirt or rinse with clear water.
–– To clean lenses: mist up the lenses or rinse with clear water and clean
them with a soft piece of cloth.
Discharged battery: Replace Battery (3)
Battery installed incorrectly: Remove and reinstall Battery (3)
with (+) toward Battery cap (2).
Battery is not making good contact: Clean contact surfaces and reinstall Battery (3).
Defective rotary switch: Notify dealer/armourer
User Manual for
Aimpoint CompM3™
and
Aimpoint CompML3™
4.2 IMPOSSIBLE TO ZERO
Adjustment screw is at its limit: Check alignment of mount to barrel
Impact point is moving: Check mount stability
CHAPTER V – MAINTENANCE
a.This reflex sight does not require any particular maintenance while used
under normal conditions.
b.Under severe weather conditions please refer to CHAPTER III.
c.Keep Lens covers (8) and (9) closed whenever the sight is not in use.
d.Warehouse storage: Remove Battery (3) and allow lens surfaces to dry
completely (if wet) before closing the Lens covers (8) and (9).
e.To clean lenses refer to CAUTION in CHAPTER III.
f. To reach maximum protection level for all weather conditions, wax is added
into the rubber mixture. The wax will slowly migrate to the surface of the
part. During frequent use this wax will be used up completely and not
noticed by he user. For long time storage, the wax will not be used up as
frequently and will be seen as a grey film on the surface. To restore to its
original condition, please hand wash in warm dishwater.
Aimpoint AB
Jägershillgatan 15
SE- 213 75 Malmö, Sweden
Phone +46 (0)40 671 50 20
Fax +46 (0)40 21 92 38
e-mail: [email protected]
www.aimpoint.com
Aimpoint Inc.
14103 Mariah Court
Chantilly, VA 20151-2113, USA
Phone +1 703-263-9795
Fax +1 703-263-9463
e-mail: [email protected]
www.aimpoint.com
© Copyright 2015 . Contents property of Aimpoint. All rights reserved. [11432-4]
CHAPTER I – PRESENTATION
1.2 SPECIFICATION
1.3 LOCATION AND DESCRIPTION OF MAJOR COMPONENTS
1.1 PRESENTATION
Material – housing: Extruded, high strength aluminum, anodized
Material – rubber cover: Chloroprene rubber (MIL-R-6855)
Material – lens covers: Thermoplastic elastomer, black, non-glare
Surface finish: Hard Anodized, Dark Graphite Grey, matte
Rubber cover: Black or Dark Earth Brown
Optical magnification: 1X
Eye relief: Unlimited, no centering required
Optical coating: Anti Reflex coating, all surfaces, Multi-layer coating for reflection, Band Pass coating for NVD* compatibility (CompM3)
Dot size: 2 and 4 MOA**
dot brightness: CompM3: 10 positions: 4 NVD, 6 daylight settings of which 1 Extra Bright
CompML3: 10 positions: 1 Off, 9 daylight of
which 1 Extra Bright
Battery: One 3V Lithium battery type 2L76 or DL1/3N
Battery life*** (hours): 50 000 h on setting 7 of 10,
Typically 500 000 h at NVD setting.
Length (incl. lens covers): 130 mm (5.1”)
Width: 62 mm (2.4”), incl rubber cover,
49 mm (1.9”) without
Height: 58 mm (2.3”), incl rubber cover,
49 mm (1.9”) without
Weight: 270 gram (9.5 oz), incl rubber cover,
220 gram (7.8 oz) without
Adjustment: Range ±2 m at 100 meters, in windage and
elevation 1 click = 13 mm at 80 meters =
16 mm at 100 meters = 1/2” at 100 yards.
Mounting: One wide ring, 30 mm, or Aimpoint QR Ring
Max temperature range: -45 ºC to +70 ºC (-50 ºF to +160 ºF)
Water resistance: Submersible to 45 m (135 ft) water depth
See Fig. 1
Aimpoint’s Reflex Sights are rugged precision electronic optical red dot sights
developed for civilian, military and law enforcement applications.
Aimpoint sights are designed for the ”two eyes open” method of sighting, which
greatly enhances situational awareness and target acquisition speed. Thanks
to the parallax-free design, the dot follows the movement of the user’s eye
while remaining fixed on the target, eliminating any need for centering. Further,
the sight allows for unlimited eye-relief.
The CompM3 is compatible with 1st , 2nd and 3rd generation night vision
devices, while the CompML3 is optimized for applications, which do not require
night vision compatibility.
The CompM3 and CompML3 sights are using the revolutionary Advanced
Circuit Efficiency Technology, ACET. ACET combines Aimpoint’s superior
accuracy and ease of use with significantly low power usage.
*NVD: Night Vision Device
**MOA: Minute Of Angle 1MOA ≈ 30 mm at 100 meters ≈ 1” at 100 yards
***Average values, depending on brightness setting
CHAPTER II – OPERATION UNDER NORMAL CONDITIONS
2.1 ASSEMBLY AND PREPARATION FOR USE
Comp M3/ML3
9
2
3
5
Right-handed shooter
configuration
Left-handed shooter
configuration
WARNING: Ensure that the weapon is unloaded and the safety selector
is in the ”safe” position before attempting to install, remove or perform
maintenance on the sight.
2.1.1 Installing Battery
8
a.Remove Battery cap (2) by turning it counter clockwise.
b.Insert Battery (3) with positive (+) end toward Battery cap (2).
CAUTION: When replacing battery check that the O-ring is present and not
damaged. Failure to do so could result in water leakage into the battery
compartment.
10
6
7
Fig. 2
1
7
4
Fig. 3
5
2.1.2 Installing Ring and Sight on the weapon
Aimpoint’s sights are designed for installation on most types of weapons.
If your weapon does not have or support an appropriate base(s), please
consult your dealer, gunsmith or other qualified source.
Installing the Rubber Cover
(RIGHT-HANDED SHOOTER CONFIGURATION ONLY!)
6
1. Sight
2. Battery Cap
3. Battery (DL1/3N or similar)
4. Rotary Switch
5. Cap Adjustment (2 pcs)
6. Rubber Strap (2 pcs)
7. Adjustment screws for elevation/windage (2 pcs)
8. Lens Cover, rear
9. Lens Cover, front
10. Rubber Cover
c.Install Battery cap (2) by turning clockwise until snug. Hand tighten only.
Using tools could damage equipment.
d.Verify that red dot is present by turning the Rotary switch (4) clockwise.
a.Assemble the sight to the weapon by using Aimpoint’s wide 30 mm ring
or QR-mount. If other standard 30 mm rings are used, make sure that the
ring(s) covers a length of minimum 25 mm or 1”.
b.Ensure that the sight is correctly positioned for right or left hand shooting.
See (fig 2) and (fig. 3).
NOTE: Installing the Rubber cover (10) requires right-handed shooter
configuration (fig. 2).
Fig. 1
c.When using lens covers, ensure that they are correctly positioned and can
be opened.
NOTE: make sure that you have space between the bottom front part of the
sight and the top of the base/weapon.
Fig. 4
Fig. 5
d.Finally, make sure that all screws are firmly tightened around the sight.
e.Complete zeroing according to (2.2.1).
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement