LVD Report__A2 2013_YS902672

LVD Report__A2 2013_YS902672
Report No.: T1505073-051
Particulars: test item vs. test requirements
Equipment mobility ....................................................: Transportable and movable
Connection to the mains............................................: non-detachable power supply cord
Operating condition ...................................................: Continuous
Access location .........................................................: Operator accessible
Over voltage category (OVC) ...................................: II
Mains supply tolerance (%) or absolute mains supply -10%, +10%
values .......................................................................:
Tested for IT power systems ....................................: N/A
IT testing, phase-phase voltage (V) .........................: N/A
Class of equipment ...................................................: Class II
Considered current rating (A) ...................................: 16A
Pollution degree (PD) ...............................................: PD2
IP protection class ....................................................: IPX0
Altitude during operation (m) ....................................: Up to 2000
Altitude of test laboratory (m) ...................................: Below 2000
Mass of equipment (kg) ............................................: Approx. 0.245
Possible test case verdicts:
- test case does not apply to the test object................. : N/A
- test object does meet the requirement....................... : P (Pass)
- test object does not meet the requirement................. : F (Fail)
Testing
Date of receipt of test item ............................................ : 2015-05-16
Date(s) of performance of tests .................................... : 2015-05-16 to 2015-05-20
Rev 2.0
Page 2 of 73
Report No.: T1505073-051
General remarks:
If any questions of the inspection report, please proposed with in 15 days from receiving the report,
deadline will not be accepted.
Report would be inefficiency if any scrawling or modification was made.
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(see Enclosure #)" refers to additional information appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a point is used as the decimal separator.
The instructions specified by the standard have to be in official language of each country, however, only
English is checked for this report. It is the applicant responsibility to provide instruction in each official
language of the EU.
This report is submitted for the exclusive use of the client to whom it is addressed. Its significance is
subject to the adequacy and representative character of the sample(s) and to the comprehensiveness of
the tests, examinations or surveys made.
This report justified only the submitted samples exclusively and not necessarily implies that all other
samples are also to be found in same result.
The CE marking may only be used if all relevant and effective EC directives are complied with.
Rev 2.0
Page 3 of 73
Report No.: T1505073-051
Factor(ies):
Yesa Technology Co., Ltd
No. 1504, Launch Industrail Zone, North Of Wuhe Rd, Bantian, Longgang, Shenzhen, China
General product information:
The equipment is transportable type Battery charger used for information technology equipment.
The equipment’s top enclosure is secured to bottom enclosure by screw.
The manufacturer declared that the maximum ambient temperature is 35°C.
Other comments:
None
Rev 2.0
Page 4 of 73
Report No.: T1505073-051
Copy of marking plate and summary of test results (information/comments):
Note(s): The above label is a draft of an artwork for marking plate pending approval by National
Certification Bodies and it shall not be affixed to products prior to such an approval.
Rev 2.0
Page 5 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
1
GENERAL
P
1.5
Components
P
1.5.1
General
See below.
P
Comply with IEC 60950-1 or relevant component
standard
(see appended tables 1.5.1)
P
1.5.2
Evaluation and testing of components
Components certified to IEC
standards and/or their
harmonized standards, are
used within their ratings and
are checked for correct
application. Components,
which no relevant IECStandard exists, are used
within their ratings and are
tested under the conditions
occurring in the equipment
P
1.5.3
Thermal controls
No thermal controls.
1.5.4
Transformers
Transformer used are suitable
for their intended application
and comply with the relevant
requirements of the standard
and particularly Annex C.
1.5.5
Interconnecting cables
Not such cables used.
N/A
1.5.6
Capacitors bridging insulation
No such components.
N/A
1.5.7
Resistors bridging insulation
No such components
N/A
1.5.7.1
Resistors bridging functional, basic or
supplementary insulation
1.5.7.2
Resistors bridging double or reinforced insulation
between a.c. mains and other circuits
No such components.
N/A
1.5.7.3
Resistors bridging double or reinforced insulation
between a.c. mains and antenna or coaxial cable
No such components.
N/A
1.5.8
Components in equipment for IT power systems
No such components.
N/A
1.5.9
Surge suppressors
No such components.
N/A
1.5.9.1
General
No such components.
N/A
1.5.9.2
Protection of VDRs
N/A
1.5.9.3
Bridging of functional insulation by a VDR
N/A
1.5.9.4
Bridging of basic insulation by a VDR
Rev 2.0
Result - Remark
Page 6 of 73
Verdict
N/A
P
N/A
No such components.
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
1.5.9.5
Bridging of supplementary, double or reinforced
insulation by a VDR
No such components.
1.6
Power interface
1.6.1
AC power distribution systems
TN power system.
P
1.6.2
Input current
Highest load according to
1.2.2.1 for this equipment is
the operation with the max.
specified DC-load.
(see appended table 1.6.2)
P
1.6.3
Voltage limit of hand-held equipment
Not hand-held equipment.
1.6.4
Neutral conductor
Class II equipment. The
neutral is not identified in the
equipment. Double or
reinforced insulation for rated
voltage between accessible
parts and primary phases.
1.7
Marking and instructions
P
1.7.1
Power rating and identification markings
P
1.7.1.1
Power rating marking
See below
N/A
P
P
N/A
Rated voltage(s) or voltage range(s) (V) ...............:
AC 220-240V
Symbol for nature of supply, for d.c. only...............:
Mains from AC source
Rated frequency or rated frequency range (Hz) ....:
50/60Hz
P
Rated current (mA or A) .........................................:
350mA
P
Identification markings
See below
P
P
N/A
P
Manufacturer’s name or trade-mark or identification
mark .......................................................................:
Rev 2.0
N/A
P
Multiple mains supply connections..........................: Only one mains supply
connections.
1.7.1.2
Verdict
Model identification or type reference ...................:
YS902672
P
Symbol for Class II equipment only .......................:
Double square symbol
provided.
P
Other markings and symbols ................................:
Additional symbols or marking
do not give rise to
misunderstanding.
P
Page 7 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
1.7.1.3
Use of graphical symbols
Graphical symbols are all
explained in the user’s
manual.
P
1.7.2
Safety instructions and marking
See below.
P
1.7.2.1
General
P
1.7.2.2
Disconnect devices
1.7.2.3
Overcurrent protective device
The user’s manual contains
information for operation,
installation, servicing,
transport, storage and
technical data. The operation
guide is provided to the user.
The mains plug is regarded
as disconnected device and it
is incorporated with
equipment during normal use.
Pluggable equipment type A
1.7.2.4
IT power distribution systems
It shall be evaluated when
submitted for Norway national
approval.
N/A
1.7.2.5
Operator access with a tool
No operator accessible area
that needs to be accessed by
the use of a tool.
N/A
1.7.2.6
Ozone
The equipment not containing
Ozone.
N/A
1.7.3
Short duty cycles
The equipment is intended for
continuous operation.
N/A
1.7.4
Supply voltage adjustment ...................................:
No voltage selector.
N/A
Methods and means of adjustment; reference to
installation instructions .........................................:
Verdict
P
N/A
N/A
1.7.5
Power outlets on the equipment ...........................:
No power outlets provided.
1.7.6
Fuse identification (marking, special fusing
characteristics, cross-reference) ..........................:
Current fuse (F1) used,
marking adjacent to it:
T1A/250Vac.
1.7.7
Wiring terminals
No such terminals
N/A
1.7.7.1
Protective earthing and bonding terminals ...........:
Class II equipment.
N/A
1.7.7.2
Terminals for a.c. mains supply conductors
No such terminals.
N/A
1.7.7.3
Terminals for d.c. mains supply conductors
AC mains supply only.
N/A
1.7.8
Controls and indicators
No safety relevant controls or
indicators
N/A
1.7.8.1
Identification, location and marking.......................:
N/A
1.7.8.2
Colours .................................................................:
N/A
Rev 2.0
Page 8 of 73
N/A
P
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
1.7.8.3
Symbols according to IEC 60417.........................:
There are no mains switches
in the equipment.
N/A
1.7.8.4
Markings using figures ........................................:
No controls affecting safety.
N/A
1.7.9
Isolation of multiple power sources ......................:
Only one supply from the
mains.
N/A
1.7.10
Thermostats and other regulating devices ..........:
No thermostats or other
regulating devices.
N/A
1.7.11
Durability
he label was subjected to the
permanence of marking test.
The label was rubbed with
cloth soaked with water for 15
s and then again for 15s with
the cloth soaked with
petroleum spirit.
P
After this test there was no
damage to the label. The
marking on the label did not
fade. There was neither
curling nor lifting of the label
edge
1.7.12
Removable parts
No removable parts provided.
N/A
1.7.13
Replaceable batteries ..........................................:
No battery provided.
N/A
⎯
Language(s) ........................................................ :
1.7.14
Equipment for restricted access locations ...........:
2
PROTECTION FROM HAZARDS
P
2.1
Protection from electric shock and energy hazards
P
2.1.1
Protection in operator access areas
See below
P
2.1.1.1
Access to energized parts
See below.
P
Test by inspection .................................................:
No access with test finger and
test pin to any parts with only
basic insulation to ELV or
hazardous voltage.
P
Test with test finger (Figure 2A) ............................:
See above.
P
Test with test pin (Figure 2B) ................................:
See above.
P
Test with test probe (Figure 2C) ............................:
No TNV circuits in the
equipment.
N/A
Battery compartments
No battery compartments
N/A
2.1.1.2
Rev 2.0
Page 9 of 73
No restricted access location.
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
2.1.1.3
Access to ELV wiring
No ELV wiring in operator
accessible area.
Working voltage (Vpeak or Vrms); minimum
distance through insulation (mm)
see appended tables 2.10.2
and 2.10.5
⎯
2.1.1.4
Access to hazardous voltage circuit wiring
No hazardous voltage wiring
in operator accessible area.
N/A
2.1.1.5
Energy hazards .....................................................:
Energy does not exceed
240VA between any two
points in accessible parts (o/p
connector of secondary
circuit). Results see
appended table 2.1.1.5. No
energy hazard in operator
access area.
P
2.1.1.6
Manual controls
Not connected to and
sufficiently separated from
hazardous voltages.
2.1.1.7
Discharge of capacitors in equipment
2.1.1.8
Verdict
N/A
N/A
P
Measured voltage (V); time-constant (s) ................:
(see appended table 2.1.1.7)
Energy hazards – d.c. mains supply
Connected to a.c. mains.
⎯
N/A
a) Capacitor connected to the d.c. mains supply ..:
N/A
b) Internal battery connected to the d.c. mains
supply ....................................................................:
N/A
2.1.1.9
Audio amplifiers .....................................................:
No Audio amplifiers.
N/A
2.1.2
Protection in service access areas
N/A
2.1.3
Protection in restricted access locations
No service access areas.
No restricted access
locations.
2.2
SELV circuits
2.2.1
General requirements
See below.
P
2.2.2
Voltages under normal conditions (V) ...................:
Between any conductors of
the SELV circuits 42.4 V peak
or 60 V d.c. are not exceeded.
(See appended table 2.2.2.)
P
Rev 2.0
N/A
P
Page 10 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
2.2.3
Voltages under fault conditions (V) .......................:
Single fault did not cause
excessive voltage in
accessible SELV circuits.
Limits of 71V peak and 120V
d.c. were not exceeded within
0.2 seconds and limits 42.4V
peak and 60V d.c. were not
exceeded for longer than 0.2
seconds.
P
2.2.4
Connection of SELV circuits to other circuits ......:
See above.
P
2.3
TNV circuits
2.3.1
Limits
See below.
Type of TNV circuits ...............................................:
No TNV circuits in the
equipment.
N/A
N/A
⎯
2.3.2
Separation from other circuits and from accessible
parts
N/A
2.3.2.1
General requirements
N/A
2.3.2.2
Protection by basic insulation
N/A
2.3.2.3
Protection by earthing
N/A
2.3.2.4
Protection by other constructions ..........................:
N/A
2.3.3
Separation from hazardous voltages
N/A
⎯
Insulation employed ...............................................:
2.3.4
Connection of TNV circuits to other circuits
N/A
⎯
Insulation employed ...............................................:
2.3.5
Test for operating voltages generated externally
2.4
Limited current circuits
P
2.4.1
General requirements
P
2.4.2
Limit values
See below
P
Frequency (Hz).......................................................:
(see appended table 2.4.2)
⎯
Measured current (mA) ..........................................:
(see appended table 2.4.2)
⎯
Measured voltage (V) .............................................:
(see appended table 2.4.2)
⎯
Measured circuit capacitance (nF or µF) ...............:
CY1=2200pF
⎯
Connection of limited current circuits to other
circuits
See 2.2.2 and 2.2.3. No direct
connection between SELV
and any primary circuits.
P
2.4.3
Rev 2.0
Page 11 of 73
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
2.5
Limited power sources
N/A
a) Inherently limited output
N/A
b) Impedance limited output
N/A
c) Regulating network limited output under normal
operating and single fault condition
Use of integrated circuit (IC) current limiters
N/A
d) Overcurrent protective device limited output
N/A
Max. output voltage (V), max. output current (A),
max. apparent power (VA) .....................................:
N/A
Current rating of overcurrent protective device (A) .: No such parts used.
N/A
2.6
Provisions for earthing and bonding
N/A
2.6.1
Protective earthing
2.6.2
Functional earthing
N/A
Use of symbol for functional earthing ...................:
N/A
N/A
Class II equipment.
N/A
2.6.3
Protective earthing and protective bonding
conductors
⎯
2.6.3.1
General
⎯
2.6.3.2
Size of protective earthing conductors
N/A
2
Rated current (A), cross-sectional area (mm ),
AWG .......................................................................:
2.6.3.3
Size of protective bonding conductors
⎯
N/A
2
Rated current (A), cross-sectional area (mm ),
AWG .......................................................................:
⎯
Protective current rating (A), cross-sectional area
(mm2), AWG ...........................................................:
⎯
2.6.3.4
Resistance of earthing conductors and their
terminations; resistance (Ω), voltage drop (V), test
current (A), duration (min) ......................................:
N/A
2.6.3.5
Colour of insulation.................................................:
N/A
2.6.4
Terminals
⎯
2.6.4.1
General
⎯
2.6.4.2
Protective earthing and bonding terminals
⎯
Rated current (A), type, nominal thread diameter
(mm) .......................................................................:
Rev 2.0
Page 12 of 73
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
2.6.4.3
Separation of the protective earthing conductor
from protective bonding conductors
2.6.5
Integrity of protective earthing
⎯
2.6.5.1
Interconnection of equipment
N/A
2.6.5.2
Components in protective earthing conductors and
protective bonding conductors
N/A
2.6.5.3
Disconnection of protective earth
N/A
2.6.5.4
Parts that can be removed by an operator
N/A
2.6.5.5
Parts removed during servicing
N/A
2.6.5.6
Corrosion resistance
N/A
2.6.5.7
Screws for protective bonding
N/A
2.6.5.8
Reliance on telecommunication network or cable
distribution system
N/A
2.7
Overcurrent and earth fault protection in primary circuits
P
2.7.1
Basic requirements
Equipment relies on 16A
rated fuse or circuit breaker of
the wall outlet installation
protection of the building
installation in regard to L to N
short circuit. Over-current
protection is provided by the
current fuse.
P
Instructions when protection relies on building
installation
The final system is
considered to be pluggable
equipment type A.
N/A
2.7.2
Faults not simulated in 5.3.7
The protection device is well
dimensioned and mounted.
P
2.7.3
Short-circuit backup protection
Pluggable equipment type A.
Building installation is
considered as providing shortcircuit backup protection.
P
2.7.4
Number and location of protective devices ............:
Over current protection by
one built-in current fuse.
P
2.7.5
Protection by several devices
Only one protective device.
See Sub-clause 2.7.4.
N/A
2.7.6
Warning to service personnel.................................:
N/A
2.8
Safety interlocks
N/A
Rev 2.0
Result - Remark
Page 13 of 73
Verdict
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
2.8.1
General principles
No safety interlock provided.
2.8.2
Protection requirements
N/A
2.8.3
Inadvertent reactivation
N/A
2.8.4
Fail-safe operation
N/A
Protection against extreme hazard
N/A
2.8.5
Moving parts
N/A
2.8.6
Overriding
N/A
2.8.7
Switches, relays and their related circuits
N/A
2.8.7.1
Separation distances for contact gaps and their
related circuits (mm)
:
N/A
2.8.7.2
Overload test
N/A
2.8.7.3
Endurance test
N/A
2.8.7.4
Electric strength test
N/A
2.8.8
Mechanical actuators
N/A
2.9
Electrical insulation
P
2.9.1
Properties of insulating materials
Natural rubber, asbestos or
hygroscopic material are not
used.
P
2.9.2
Humidity conditioning
Humidity treatment performed
at 120 h
P
Relative humidity (%), temperature (°C) ...............:
93%, 40°C
⎯
2.9.3
Grade of insulation
Please refer to 2.10, 4.5.1
and 5.2
P
2.9.4
Separation from hazardous voltages
The secondary circuit is
separated from hazardous
voltages by reinforce
insulation.
P
Method(s) used .....................................................:
Method 1 used
⎯
N/A
2.10
Clearances, creepage distances and distances through insulation
P
2.10.1
General
See below.
P
2.10.1.1
Frequency ..............................................................:
Considered.
P
2.10.1.2
Pollution degrees ...................................................:
2
P
2.10.1.3
Reduced values for functional insulation
The functional are comply
with 5.3.4 a) and c)
P
Rev 2.0
Page 14 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
2.10.1.4
Intervening unconnected conductive parts
No such part.
N/A
2.10.1.5
Insulation with varying dimensions
No such insulations.
N/A
2.10.1.6
Special separation requirements
Not used.
N/A
2.10.1.7
Insulation in circuits generating starting pulses
No such part.
N/A
2.10.2
Determination of working voltage
See below.
P
2.10.2.1
General
Considered.
P
2.10.2.2
RMS working voltage
(see appended table 2.10.2)
P
2.10.2.3
Peak working voltage
(see appended table 2.10.2)
P
2.10.3
Clearances
See below.
P
2.10.3.1
General
See below, Annex G was not
considered.
P
2.10.3.2
Mains transient voltages
See below.
P
a) AC mains supply ...............................................:
Normal transient voltage
considered (overvoltage
category II for primary circuit).
P
b) Earthed d.c. mains supplies ..............................:
Not intended for d.c.
N/A
c) Unearthed d.c. mains supplies ..........................:
Not intended for d.c.
N/A
d) Battery operation ...............................................:
Verdict
N/A
2.10.3.3
Clearances in primary circuits
Annex F and minimum
clearances considered. (see
appended table 2.10.3 and
2.10.4)
P
2.10.3.4
Clearances in secondary circuits
See 5.3.4.
P
2.10.3.5
Clearances in circuits having starting pulses
No such circuit.
2.10.3.6
Transients from a.c. mains supply ........................:
N/A
2.10.3.7
Transients from d.c. mains supply ........................:
N/A
2.10.3.8
Transients from telecommunication networks and
cable distribution systems .....................................:
2.10.3.9
Measurement of transient voltage levels
N/A
a) Transients from a mains suplply
N/A
For an a.c. mains supply .......................................:
N/A
For a d.c. mains supply .........................................:
N/A
b) Transients from a telecommunication network :
N/A
2.10.4
2.10.4.1
Rev 2.0
Creepage distances
General
Page 15 of 73
No TNV circuits in the
equipment.
N/A
N/A
(see appended table 2.10.3
and 2.10.4)
P
See below.
P
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
2.10.4.2
Material group and caomparative tracking index
Material group IIIb is assumed
to be used
P
CTI tests .................................................................:
CTI rating for all materials are
min. 100.
⎯
2.10.4.3
Minimum creepage distances
(see appended table 2.10.3
and 2.10.4)
P
2.10.5
Solid insulation
2.10.5.1
General
See below.
P
2.10.5.2
Distances through insulation
(see appended table 2.10.5)
P
2.10.5.3
Insulating compound as solid insulation
No such components.
2.10.5.4
Semiconductor devices
Approved optocoupler with
dti. ≥0.4mm used.
2.10.5.5.
Cemented joints
No cemented joints.
2.10.5.6
Thin sheet material – General
The thin sheet materials of
polyester tape used in
transformer T1.
P
2.10.5.7
Separable thin sheet material
Two layers of polyester tape
wrapped around the body of
transformer T1 were used as
reinforced insulation.
P
Number of layers (pcs) ...........................................:
2 layers.
⎯
2.10.5.8
Non-separable thin sheet material
Not applicable.
N/A
2.10.5.9
Thin sheet material – standard test procedure
Not applicable.
N/A
Electric strength test
Not applicable.
⎯
2.10.5.10
Verdict
P
Thin sheet material – alternative test procedure
N/A
P
N/A
P
Electric strength test
(See appended table 5.2)
P
2.10.5.11
Insulation in wound components
Approved source of triple
insulated wire used in T1
primary winding for reinforced
insulation.
P
2.10.5.12
Wire in wound components
See above.
P
Working voltage
See appended table C.2 in
Measurement Section.
P
:
a) Basic insulation not under stress ......................:
b) Basic, supplemetary, reinforced insulation .......:
Rev 2.0
Page 16 of 73
N/A
Reinforced insulation.
P
Report No.: T1505073-051
IEC 60950-1
Clause
2.10.5.13
2.10.5.14
Requirement + Test
Result - Remark
Verdict
c) Compliance with Annex U .................................:
Approved source of triple
insulated wire used in T1
primary winding for reinforced
insulation.
P
Two wires in contact inside wound component;
angle between 45° and 90° ...................................:
By tubing or insulation tape.
P
Wire with solvent-based enamel in wound
components
No such parts.
N/A
Electric strength test
⎯
Routine test
⎯
Additional insulation in wound components
No such construction.
N/A
Working voltage .....................................................:
N/A
- Basic insulation not under stress ........................:
N/A
- Supplemetary, reinforced insulation ....................:
N/A
2.10.6
Construction of printed boards
See below.
P
2.10.6.1
Uncoated printed boards
(see appended table 2.10.3
and 2.10.4)
P
2.10.6.2
Coated printed boards
No such parts.
N/A
2.10.6.3
Insulation between conductors on the same inner
surface of a printed board
No such parts.
N/A
2.10.6.4
Insulation between conductors on different layers
of a printed board
No such parts.
N/A
Distance through insulation
⎯
Number of insulation layers (pcs)...........................:
⎯
2.10.7
Component external terminations
No such parts.
N/A
2.10.8
Tests on coated printed boards and coated
components
No such parts.
N/A
2.10.8.1
Sample preparation and preliminary inspection
N/A
2.10.8.2
Thermal conditioning
N/A
2.10.8.3
Electric strength test
N/A
2.10.8.4
Abrasion resistance test
N/A
2.10.9
Thermal cycling
N/A
2.10.10
Test for Pollution Degree 1 environment and
insulating compound
2.10.11
Tests for semiconductor devices and cemented
joints
Rev 2.0
Page 17 of 73
No such components.
N/A
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
2.10.12
Enclosed and sealed parts
3
WIRING, CONNECTIONS AND SUPPLY
P
3.1
General
P
3.1.1
Current rating and overcurrent protection
All internal wires are UL
recognized wiring which is
PVC insulated, rated VW-1,
minimum 80°C. Internal wiring
gauge is suitable for current
intended to be carried.
P
3.1.2
Protection against mechanical damage
Wires do not touch sharp
edges, which could damage
the insulation.
P
3.1.3
Securing of internal wiring
Internal wiring is secured
reliable so that loosening of
terminal connections is
unlikely.
P
3.1.4
Insulation of conductors
Insulation of the conductor is
suitable for the application.
For insulation material see
subclause 3.1.1.
P
3.1.5
Beads and ceramic insulators
Not used.
N/A
3.1.6
Screws for electrical contact pressure
No such screws.
N/A
3.1.7
Insulating materials in electrical connections
All current carrying
connections are metal to
metal.
N/A
3.1.8
Self-tapping and spaced thread screws
No such part.
N/A
3.1.9
Termination of conductors
All conductors are reliably
secured by solder-pin or
glued or other mechanical
fixing means.
P
10 N pull test
Break away or pivot on its
terminal is unlikely.
P
3.1.10
Sleeving on wiring
No sleeving used to provide
supplementary insulation.
3.2
Connection to a mains supply
3.2.1
Means of connection
See below
P
3.2.1.1
Connection to an a.c. mains supply
Non-detachable power supply
cord with plug
P
Rev 2.0
Result - Remark
Verdict
N/A
N/A
P
Page 18 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
3.2.1.2
Connection to a d.c. mains supply
AC Source.
N/A
3.2.2
Multiple supply connections
Only one supply connection
N/A
3.2.3
Permanently connected equipment
The equipment is not
intended for permanent
connection to the mains.
N/A
⎯
Number of conductors, diameter of cable and
conduits (mm) ....................................................... :
3.2.4
Appliance inlets
N/A
3.2.5
Power supply cords
Non-detachable power supply
cord
P
3.2.5.1
AC power supply cords
(see appended table 1.5.1.)
P
Type ...................................................................... :
(see appended table 1.5.1.)
⎯
Rated current (A), cross-sectional area (mm ),
AWG ..................................................................... :
(see appended table 1.5.1.)
⎯
3.2.5.2
DC power supply cords
No connected to DC mains
N/A
3.2.6
Cord anchorages and strain relief
Test on non-detachable
power supply cords. After the
test, there was no indication
of damage and not displaced
more than 2mm. The
equipment complies with the
requirements of electric
strength test.
P
Mass of equipment (kg), pull (N) ......................... :
0.245, 30N
⎯
Longitudinal displacement (mm) .......................... :
0.12 max.
⎯
3.2.7
Protection against mechanical damage
No arts under this unit likely to
damage the power supply
cord. No sharp edges.
N/A
3.2.8
Cord guards
Integral cord guard is
provided on power supply
cord
N/A
2
3.2.9
Rev 2.0
Diameter or minor dimension D (mm); test mass (g) 3.5mm; 122.5g
............................................................................... :
⎯
Radius of curvature of cord (mm).......................... :
6.0mm
⎯
Supply wiring space
Cord guard is provided that
prevent the wiring not be
damaged and be free from its
terminal.
P
Page 19 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
3.3
Wiring terminals for connection of external conductors
P
3.3.1
Wiring terminals
P
3.3.2
Connection of non-detachable power supply cords
3.3.3
Screw terminals
3.3.4
Conductor sizes to be connected
See below.
P
Rated current (A), cord/cable type, cross-sectional
area (mm2)............................................................. :
(See appended table 1.5.1.)
⎯
Wiring terminal sizes
No such wiring terminal.
Supply cord is soldered on
PCB and additionally fixed by
glue.
N/A
3.3.5
Result - Remark
No special non-detachable
power supply cord used.
Verdict
N/A
N/A
⎯
Rated current (A), type, nominal thread diameter
(mm) ..................................................................... :
3.3.6
Wiring terminal design
N/A
3.3.7
Grouping of wiring terminals
N/A
3.3.8
Stranded wire
3.4
Disconnection from the mains supply
3.4.1
General requirement
See below.
P
3.4.2
Disconnect devices
The mains plug on the power
cord is regarded as
disconnected device and it is
incorporated with equipment
during normal use.
P
3.4.3
Permanently connected equipment
Not permanently connected
equipment.
3.4.4
Parts which remain energized
There is no parts remained
with hazardous voltage or
energy in the equipment when
SPS is separated from AC
mains.
3.4.5
Switches in flexible cords
3.4.6
Number of poles – single-phase and d.c.
equipment
See sub-clause 1.7.2.2.
The disconnected device
disconnects both poles
simultaneously.
3.4.7
Number of poles – three-phase equipment
Single phase.
Rev 2.0
The conductor is not subject
to contact pressure.
N/A
P
N/A
P
N/A
Page 20 of 73
P
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
3.4.8
Switches as disconnect devices
No switches provided.
N/A
3.4.9
Plugs as disconnect devices
(see sub-clause 3.4.2)
P
3.4.10
Interconnected equipment
No interconnections using
hazardous voltages.
N/A
3.4.11
Multiple power sources
Only one supply connection
provided.
N/A
3.5
Interconnection of equipment
3.5.1
General requirements
Considered.
P
3.5.2
Types of interconnection circuits .......................... :
SELV Circuit.
P
3.5.3
ELV circuits as interconnection circuits
No ELV interconnection.
N/A
3.5.4
Data ports for additional equipment
No data ports.
N/A
4
PHYSICAL REQUIREMENTS
P
4.1
Stability
P
P
Angle of 10
Less than 7kg.
Test force (N) ........................................................:
4.2
Mechanical strength
4.2.1
General
Steady force test, 10 N
4.2.3
Steady force test, 30 N
4.2.4
Steady force test, 250 N
4.2.5
Impact test
Rev 2.0
N/A
N/A
P
See below. After the tests, the
equipment complies with the
requirements of sub-clauses
2.1.1, 2.6.1, 2.10 and 4.4.1.
No such equipment
10 N applied to all
components other than the
parts serving as an enclosure.
No internal enclosure
Rack-mounted equipment.
4.2.2
Verdict
P
N/A
P
N/A
Fall test
250N applied to outer
enclosure. No energy or other
hazards.
Test was performed for all
sources of enclosure material.
Not applied for direct plug-in
equipment.
See above.
N/A
Swing test
See above.
N/A
Page 21 of 73
P
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
4.2.6
Drop test; height (mm) ...........................................:
4.2.7
Stress relief test
The equipment has been
subjected to three drops from
1m height on a hard wooden
surface.
No hazard as result from drop
test.
After 7 hours at temperature
of 85°C and cooling down to
room temperature, no
shrinkage, distortion or
loosening any enclosure part
was noticeable on the
equipment.
4.2.8
Cathode ray tubes
No cathode ray tube.
Picture tube separately certified ............................:
Verdict
P
P
N/A
N/A
4.2.9
High pressure lamps
No high pressure lamp.
N/A
4.2.10
Wall or ceiling mounted equipment; force (N) .......:
Not wall or ceiling mounted
equipment.
N/A
4.3
Design and construction
4.3.1
Edges and corners
All edges and corners are
rounded and/or smoothed
4.3.2
Handles and manual controls; force (N) ............ :
No handles or controls
provided.
N/A
4.3.3
Adjustable controls
No adjustable controls.
N/A
4.3.4
Securing of parts
No loosening of parts
impairing creepage distances
or clearances is likely to occur
P
4.3.5
Connection by plugs and sockets
No mismating of connectors,
plugs or sockets possible.
P
4.3.6
Direct plug-in equipment
Not direct plug-in equipment.
N/A
P
P
Torque ..................................................................:
N/A
Compliance with the relevant mains plug standard
...............................................................................:
N/A
4.3.7
Heating elements in earthed equipment
No heating elements provided
N/A
4.3.8
Batteries
No battery provided.
N/A
Rev 2.0
- Overcharging of a rechargeable battery
N/A
- Unintentional charging of a non-rechargeable
battery
N/A
Page 22 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
- Reverse charging of a rechargeable battery
N/A
- Excessive discharging rate for any battery
N/A
4.3.9
Oil and grease
Insulation is not exposed to oil
and grease etc
N/A
4.3.10
Dust, powders, liquids and gases
The equipment does not
contain flammable liquids or
gases
N/A
4.3.11
Containers for liquids or gases
No containers for liquids or
gases in the equipment
N/A
4.3.12
Flammable liquids ................................................:
The equipment does not
contain flammable liquid
N/A
Quantity of liquid (l) ..............................................:
N/A
Flash point (°C) ....................................................:
N/A
4.3.13
Radiation
4.3.13.1
General
4.3.13.2
Ionizing radiation
4.3.13.3
No radiation hazards.
N/A
⎯
No ionizing radiation or
flammable liquids present.
N/A
Measured radiation(pA/kg) ...................................:
⎯
Measured high-voltage (kV) ..................................:
⎯
Measured focus voltage (kV) ................................:
⎯
CRT markings .......................................................:
⎯
Effect of ultraviolet (UV) radiation on materials
No UV radiation.
N/A
Part, property, retention after test, flammability
classification .........................................................:
N/A
4.3.13.4
Human exposure to ultraviolet (UV) radiation ......:
N/A
4.3.13.5
Lasers (including laser diodes) and LEDs
4.3.13.5.1
Lasers (including laser laser diodes)
The LED is considered as
indicating light.
N/A
⎯
Laser class ...........................................................:
4.3.13.5.2
Light emitting diodes (LEDs)
The output radiation of the
LED indicator (optional) is far
less than the limit of laser
class 1.
4.3.13.6
Other types ...........................................................:
Not used.
4.4
Protection against hazardous moving parts
Rev 2.0
Page 23 of 73
P
P
N/A
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
4.4.1
General
No moving parts.
N/A
4.4.2
Protection in operator access areas ....................:
N/A
Household and home/office document/media
shredders
N/A
4.4.3
Protection in restricted access locations ..............:
N/A
4.4.4
Protection in service access areas
N/A
4.4.5
Protection against moving fan blades
N/A
4.4.5.1
General
N/A
Not considered to cause pain or injury.
a)………….:
N/A
Is considered to cause pain, not injury.
b) …………:
N/A
Considered to cause injury.
c) …………:
N/A
Protection for users
N/A
Use of symbol or
warning ……………………………:
N/A
Protection for service persons
N/A
Use of symbol or
warning ……………………………:
N/A
4.4.5.2
4.4.5.3
P
4.5
Thermal requirements
4.5.1
General
See below.
P
4.5.2
Temperature tests
(see appended table 4.5)
P
Normal load condition per Annex L ......................:
See Annex L.
⎯
4.5.3
Temperature limits for materials
(see appended table 4.5)
P
4.5.4
Touch temperature limits
(see appended table 4.5)
P
4.5.5
Resistance to abnormal heat .................................... Phenolic bobbin material used
in Transformer T1, which
acceptable without test. No
other parts to be tested.
4.6
Openings in enclosures
4.6.1
Top and side openings
P
No openings.
Rev 2.0
Bottoms of fire enclosures
(see appended table 4.6.1)
Page 24 of 73
N/A
⎯
Dimensions (mm) .................................................:
4.6.2
N/A
P
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
⎯
Construction of the bottomm, dimensions (mm) ..:
4.6.3
Doors or covers in fire enclosures
No doors or covers provided.
N/A
4.6.4
Openings in transportable equipment
Not applicable.
N/A
4.6.4.1
Constructional design measures
N/A
⎯
Dimensions (mm) .................................................:
4.6.4.2
Evaluation measures for larger openings
N/A
4.6.4.3
Use of metallized parts
N/A
4.6.5
Adhesives for constructional purposes
No adhesives for
constructional purposes.
N/A
Conditioning temperature (°C), time (weeks)........:
⎯
4.7
Resistance to fire
P
4.7.1
Reducing the risk of ignition and spread of flame
Use of materials with the
required flammability classes.
Method 1, selection and application of components (see appended table 4.7)
wiring and materials
Method 2, application of all of simulated fault
condition tests
P
P
N/A
4.7.2
Conditions for a fire enclosure
See below.
P
4.7.2.1
Parts requiring a fire enclosure
With having the following
parts:
P
-
Components in primary
-
Components in
secondary
-
Components having
unenclosed arcing parts
at hazardous voltage or
energy level.
-
Insulated wiring
The fire enclosure is required.
4.7.2.2
Parts not requiring a fire enclosure
4.7.3
Materials
4.7.3.1
General
Parts mounted on PCB of
flammability class V-1 or
better.
P
4.7.3.2
Materials for fire enclosures
V-1 or better.
P
Rev 2.0
All parts are located inside a
fire enclosure.
N/A
P
Page 25 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
4.7.3.3
Materials for components and other parts outside
fire enclosures
No such component.
4.7.3.4
Materials for components and other parts inside
fire enclosures
Other materials inside fire
enclosure are minimum V-2
material.
4.7.3.5
Materials for air filter assemblies
No air filter.
N/A
4.7.3.6
Materials used in high-voltage components
No high-voltage components.
N/A
5
ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS
P
5.1
Touch current and protective conductor current
P
5.1.1
General
5.1.2
Configuration of equipment under test (EUT)
P
5.1.2.1
Single connection to an a.c. mains supply
P
5.1.2.2
Redundant multiple connections to an a.c. mains
supply
N/A
5.1.2.3
Simultaneous multiple connections to an a.c. mains
supply
N/A
5.1.3
Test circuit
Equipment of figure 5A used.
P
5.1.4
Application of measuring instrument
Using measuring instrument
in annex D.
P
5.1.5
Test procedure
The touch current was
measured from mains to
secondary circuit and
enclosure.
P
5.1.6
Test measurements
See below.
P
Supply voltage (V) ................................................:
(see appended table 5.1.6)
⎯
Measured touch current (mA) ..............................:
(see appended table 5.1.6)
⎯
Max. allowed touch current (mA) .........................:
(see appended table 5.1.6)
⎯
See sub-clauses 5.1.2 to
5.1.6.
Verdict
N/A
P
P
Measured protective conductor current (mA) .......:
⎯
Max. allowed protective conductor current (mA)...:
⎯
5.1.7
Equipment with touch current exceeding 3,5 mA
N/A
5.1.7.1
General .................................................................:
⎯
5.1.7.2
Simultaneous multiple connections to the supply
⎯
5.1.8
Touch currents to telecommunication networks and Not connected to
cable distribution systems and from
telecommunication networks.
telecommunication networks
Rev 2.0
Page 26 of 73
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
5.1.8.1
Limitation of the touch current to a
telecommunication network or to a cable
distribution system
5.1.8.2
Result - Remark
Verdict
N/A
Supply voltage (V) ................................................:
⎯
Measured touch current (mA) ..............................:
⎯
Max. allowed touch current (mA) .........................:
⎯
Summation of touch currents from
telecommunication networks
Not connected to a
telecommunication network.
N/A
a) EUT with earthed telecommunication ports .....:
⎯
b) EUT whose telecommunication ports have no
reference to protective earth
⎯
5.2
Electric strength
P
5.2.1
General
(see appended table 5.2)
P
5.2.2
Test procedure
(see appended table 5.2)
P
5.3
Abnormal operating and fault conditions
5.3.1
Protection against overload and abnormal
operation
(see appended table 5.3)
5.3.2
Motors
No motors.
5.3.3
Transformers
With the shorted o/p of the
transformer, no high
temperature of the transformer
was recorded.
Results of the short-circuit
tests see appended table 5.3
and Annex C.
P
5.3.4
Functional insulation..............................................:
Method c). Test results see
appended table 5.3.
P
5.3.5
Electromechanical components
No electromechanical
components in secondary
circuits.
N/A
5.3.6
Audio amplifiers in ITE .........................................:
No audio amplifiers inside
equipment.
N/A
5.3.7
Simulation of faults
(see appended table 5.3)
P
5.3.8
Unattended equipment
No thermostats, temperature
limiters or thermal cut-outs
Rev 2.0
Page 27 of 73
P
P
N/A
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
5.3.9
Compliance criteria for abnormal operating and
fault conditions
5.3.9.1
During the tests
5.3.9.2
After the tests
No fire propagated beyond
the equipment. No molten
metal was emitted. Electric
strength test primary to SELV
was passed.
No fire occurred beyond the
equipment, no molten metal
emitted and no deformation of
enclosure.
Electric strength test primary to
SELV was passed.
6
CONNECTION TO TELECOMMUNICATION NETWORKS
N/A
6.1
Protection of telecommunication network service persons, and users of other
equipment connected to the network, from hazards in the equipment
N/A
6.1.1
Protection from hazardous voltages
N/A
6.1.2
Separation of the telecommunication network from earth
N/A
6.1.2.1
Requirements
N/A
P
P
P
Supply voltage (V) ................................................:
⎯
Current in the test circuit (mA) ...........................:
⎯
6.1.2.2
Exclusions ............................................................:
N/A
6.2
Protection of equipment users from overvoltages on telecommunication
networks
N/A
6.2.1
Separation requirements
N/A
6.2.2
Electric strength test procedure
N/A
6.2.2.1
Impulse test
N/A
6.2.2.2
Steady-state test
N/A
6.2.2.3
Compliance criteria
N/A
6.3
Protection of the telecommunication wiring system from overheating
N/A
6.2.1-6.2.2.3: No TNV circuits.
Max. output current (A) .........................................:
⎯
Current limiting method ........................................:
⎯
7
CONNECTION TO CABLE DISTRIBUTION SYSTEMS
N/A
7.1
General
N/A
Rev 2.0
7.1-7.4.3: Not connected to
cable distribution systems.
Page 28 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
7.2
Protection of cable distribution system service
persons, and users of other equipment connected
to the system, from hazardous voltages in the
equipment
N/A
7.3
Protection of equipment users from overvoltages
on the cable distribution system
N/A
7.4
Insulation between primary circuits and cable
distribution systems
N/A
7.4.1
General
N/A
7.4.2
Voltage surge test
N/A
7.4.3
Impulse test
N/A
A
ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE
N/A
A.1
Flammability test for fire enclosures of movable
equipment having a total mass exceeding 18kg,
and of stationary equipment (see 4.7.3.2)
Refer below:
N/A
A.1.1
Samples.................................................................:
Product mass <18kg
N/A
Wall thickness (mm) ..............................................:
⎯
A.1.2
Conditioning of samples; temperature (°C) ..........:
N/A
A.1.3
Mounting of samples ............................................:
N/A
A.1.4
Test flame (see IEC 60695-11-3)
N/A
Flame A, B, C or D ...............................................:
⎯
A.1.5
Test procedure
N/A
A.1.6
Compliance criteria
N/A
Sample 1 burning time (s) .....................................:
⎯
Sample 2 burning time (s) .....................................:
⎯
Sample 3 burning time (s) .....................................:
⎯
A.2
Flammability test for fire enclosures of movable equipment having a total mass not
exceeding 18 kg, and for material and components located inside fire enclosures
(see 4.7.3.2 and 4.7.3.4)
N/A
A.2.1
Samples, material..................................................:
N/A
Wall thickness (mm) ..............................................:
⎯
A.2.2
Conditioning of samples; temperature (°C) ..........:
N/A
A.2.3
Mounting of samples ............................................:
N/A
A.2.4
Test flame (see IEC 60695-11-4)
N/A
Rev 2.0
Page 29 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
⎯
Flame A, B or C ....................................................:
A.2.5
Test procedure
N/A
A.2.6
Compliance criteria
N/A
A.2.7
Sample 1 burning time (s) .....................................:
⎯
Sample 2 burning time (s) .....................................:
⎯
Sample 3 burning time (s) .....................................:
⎯
Alternative test acc. To IEC 60695-11-5, cl. 5 and 9
N/A
Sample 1 burning time (s) .....................................:
⎯
Sample 2 burning time (s) .....................................:
⎯
Sample 3 burning time (s) .....................................:
⎯
A.3
Hot flaming oil test (see 4.6.2)
N/A
A.3.1
Mounting of samples
N/A
A.3.2
Test procedure
N/A
A.3.3
Compliance criterion
N/A
B
ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see 4.7.2.2 and
5.3.2)
N/A
B.1
General requirements
N/A
No motor provided.
Position .................................................................:
⎯
Manufacturer ........................................................:
⎯
Type ......................................................................:
⎯
Rated values .......................................................:
⎯
B.2
Test conditions
N/A
B.3
Maximum temperatures
N/A
B.4
Running overload test
N/A
B.5
Locked-rotor overload test
N/A
Test duration (days) .............................................:
⎯
Electric strength test: test voltage (V) ..................:
⎯
B.6
Running overload test for d.c. motors in secondary
circuits
N/A
B.6.1
General
N/A
B.6.2
Test procedure
N/A
B.6.3
Alternative test procedure
N/A
Rev 2.0
Page 30 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
B.6.4
Electric strength test; test voltage (V) ..................:
N/A
B.7
Locked-rotor overload test for d.c. motors in
secondary circuits
N/A
B.7.1
General
N/A
B.7.2
Test procedure
N/A
B.7.3
Alternative test procedure
N/A
B.7.4
Electric strength test; test voltage (V) .................:
N/A
B.8
Test for motors with capacitors
N/A
B.9
Test for three-phase motors
N/A
B.10
Test for series motors
N/A
C
Result - Remark
Verdict
Operating voltage (V) ...........................................:
⎯
ANNEX C, TRANSFORMERS (see 1.5.4 and 5.3.3)
P
Position .................................................................:
T1
⎯
Manufacturer ........................................................:
(see appended table 1.5.1)
⎯
Type ......................................................................:
(see appended table 1.5.1)
⎯
Rated values .......................................................:
Class B
⎯
Method of protection..............................................:
By protection circuit design.
⎯
C.1
Overload test
(see appended table 5.3)
P
C.2
Insulation
(see appended table 5.2)
P
Protection from displacement of windings ............:
By tube or insulation tape.
P
D
ANNEX D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS (see
5.1.4)
P
D.1
Measuring instrument
P
D.2
Alternative measuring instrument
N/A
E
ANNEX E, TEMPERATURE RISE OF A WINDING (see 1.4.13)
N/A
F
ANNEX F, MEASUREMENT OF CLEARANCES AND CREEPAGE DISTANCES
(see 2.10 and Annex G)
G
ANNEX G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM
CLEARANCES
Rev 2.0
Page 31 of 73
P
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
G.1
Clearances
N/A
G.1.1
General
N/A
G.1.2
Summary of the procedure for determining
minimum clearances
N/A
G.2
Determination of mains transient voltage (V)
N/A
G.2.1
AC mains supply ..................................................:
N/A
G.2.2
Earthed d.c. mains supplies .................................:
N/A
G.2.3
Unearthed d.c. mains supplies .............................:
N/A
G.2.4
Battery operation ..................................................:
N/A
G.3
Determination of telecommunication network
transient voltage (V) .............................................:
N/A
G.4
Determination of required withstand voltage (V)
N/A
G.4.1
Mains transients and internal repetitive peaks .....:
N/A
G.4.2
Transients from telecommunication networks ......:
N/A
G.4.3
Combination of transients
N/A
G.4.4
Transients from cable distribution systems
N/A
G.5
Measurement of transient voltages (V)
N/A
a) Transients from a mains supply
N/A
For an a.c. mains supply
N/A
For a d.c. mains supply
N/A
b) Transients from a telecommunication network
N/A
G.6
Determination of minimum clearances .................:
N/A
H
ANNEX H, IONIZING RADIATION (see 4.3.13)
N/A
J
ANNEX J, TABLE OF ELECTROCHEMICAL
POTENTIALS (see 2.6.5.6)
N/A
Metal(s) used.........................................................:
Verdict
⎯
K
ANNEX K, THERMAL CONTROLS (see 1.5.3 and 5.3.8)
N/A
K.1
Making and breaking capacity
N/A
K.2
Thermostat reliability; operating voltage (V) ........:
N/A
K.3
Thermostat endurance test; operating voltage (V):
N/A
Rev 2.0
Page 32 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
K.4
Temperature limiter endurance; operating voltage
(V) .........................................................................:
N/A
K.5
Thermal cut-out reliability
N/A
K.6
Stability of operation
N/A
L
ANNEX L, NORMAL LOAD CONDITIONS FOR SOME TYPES OF ELECTRICAL
BUSINESS EQUIPMENT (see 1.2.2.1 and 4.5.2)
L.1
Typewriters
N/A
L.2
Adding machines and cash registers
N/A
L.3
Erasers
N/A
L.4
Pencil sharpeners
N/A
L.5
Duplicators and copy machines
N/A
L.6
Motor-operated files
N/A
L.7
Other business equipment
M
ANNEX M, CRITERIA FOR TELEPHONE RINGING SIGNALS (see 2.3.1)
N/A
M.1
Introduction
N/A
M.2
Method A
N/A
M.3
Method B
N/A
M.3.1
Ringing signal
N/A
M.3.1.1
Frequency (Hz) .....................................................:
⎯
M.3.1.2
Voltage (V) ............................................................:
⎯
M.3.1.3
Cadence; time (s), voltage (V) .............................:
⎯
M.3.1.4
Single fault current (mA) .......................................:
⎯
M.3.2
Tripping device and monitoring voltage ...............:
N/A
M.3.2.1
Conditions for use of a tripping device or a
monitoring voltage
N/A
M.3.2.2
Tripping device
N/A
M.3.2.3
Monitoring voltage (V) ..........................................:
N/A
N
ANNEX N, IMPULSE TEST GENERATORS (see 1.5.7.2, 1.5.7.3, 2.10.3.9,
6.2.2.1, 7.3.2, 7.4.3 and Clause G.5)
N/A
N.1
ITU-T impulse test generators
N/A
N.2
IEC 60065 impulse test generator
N/A
Rev 2.0
Result - Remark
Verdict
P
P
Page 33 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
P
ANNEX P, NORMATIVE REFERENCES
Q
ANNEX Q, Voltage dependent resistors (VDRs) (see 1.5.9.1)
N/A
- Preferred climatic categories .............................:
N/A
- Maximum continuous voltage ............................:
N/A
- Combination pulse current .................................:
N/A
Body of the VDR
Test according to IEC60695-11-5.........................:
N/A
Body of the VDR.
Flammability class of material ( min V-1)..............:
N/A
R
ANNEX R, EXAMPLES OF REQUIREMENTS FOR QUALITY CONTROL
PROGRAMMES
N/A
R.1
Minimum separation distances for unpopulated
coated printed boards (see 2.10.6.2)
N/A
R.2
Reduced clearances (see 2.10.3)
N/A
S
ANNEX S, PROCEDURE FOR IMPULSE TESTING (see 6.2.2.3)
N/A
S.1
Test equipment
N/A
S.2
Test procedure
N/A
S.3
Examples of waveforms during impulse testing
N/A
T
Annex T, GUIDANCE ON PROTECTION AGAINST INGRESS OF WATER (see
1.1.2)
N/A
⎯
⎯
U
Annex U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED
INSULATION (see 2.10.5.12)
P
(see appended table 1.5.1)
⎯
V
ANNEX V, AC POWER DISTRIBUTION SYSTEMS (see 1.6.1)
P
V.1
Introduction
P
V.2
TN power distribution systems
P
Rev 2.0
Page 34 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
W
ANNEX W, SUMMATION OF TOUCH CURRENTS
N/A
W.1
Touch current from electronic circuits
N/A
W.1.1
Floating circuits
N/A
W.1.2
Earthed circuits
N/A
W.2
Interconnection of several equipments
N/A
W.2.1
Isolation
N/A
W.2.2
Common return, isolated from earth
N/A
W.2.3
Common return, connected to protective earth
N/A
X
ANNEX X, MAXIMUM HEATING EFFECT IN TRANSFORMER TESTS (see
clause C.1)
N/A
X.1
Determination of maximum input current
N/A
X.2
Overload test procedure
N/A
Y
ANNEX Y, ULTRAVIOLET LIGHT CONDITIONING TEST (see 4.3.13.3)
N/A
Y.1
Test apparatus ..................................................... :
N/A
Y.2
Mounting of test samples ..................................... :
N/A
Y.3
Carbon-arc light-exposure apparatus .................. :
N/A
Y.4
Xenon-arc light exposure apparatus ................... :
N/A
Z
ANNEX Z, OVERVOLTAGE CATEGORIES (see 2.10.3.2 and Clause G.2)
AA
ANNEX AA, MANDREL TEST (see 2.10.5.8)
BB
ANNEX BB, CHANGES IN THE SECOND EDITION
CC
ANNEX CC, Evaluation of integrated circuit (IC) current limiters
N/A
CC.1
General
N/A
CC.2
Test program 1……………………………………….:
N/A
CC.3
Test program 2……………………………………….:
N/A
CC.4
Test program 3.....................................................:
N/A
CC.5
Compliance...........................................................:
N/A
Rev 2.0
Result - Remark
P
N/A
⎯
No provided.
Page 35 of 73
Verdict
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
DD
ANNEX DD, Requirements for the mounting means of rack-mounted
equipment
N/A
DD.1
General
N/A
DD.2
Mechanical strength test, variable N………………..:
N/A
DD.3
Mechanical strength test, 250N, including end
stops……………………………………………………:
N/A
DD.4
Compliance……………………………………………:
N/A
EE
ANNEX EE, Household and home/office document/media shredders
N/A
EE.1
General
N/A
EE.2
Markings and instructions
N/A
Use of markings or symbols…………………………:
N/A
Information of user instructions, maintenance and/or
servicing instructions…………………………:
N/A
EE.3
Inadvertent reactivation test…………………………:
N/A
EE.4
Disconnection of power to hazardous moving parts:
N/A
Use of markings or symbols…………………………:
N/A
Protection against hazardous moving parts
N/A
Test with test finger (Figure 2A) ……………………:
N/A
Test with wedge probe (Figure EE1 and EE2) ……:
N/A
EE.5
Rev 2.0
Result - Remark
The equipment is not such
equipment.
The equipment is not such
equipment.
Page 36 of 73
Verdict
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/A2:2013 – CENELEC COMMON MODIFICATIONS
Contents
(A2:2013)
General
Clauses, subclauses, notes, tables and figures which are additional to those in
IEC60950-1 and it´s amendmets are prefixed “Z”
P
Add the following annexes:
P
Annex ZA (normative)
Normative references to international
publications with their corresponding European
publications
Annex ZB (normative)
Annex ZD (informative)
Special national conditions
IEC and CENELEC code designations for
flexible cords
Delete all the “country” notes in the reference document (IEC 60950-1:2005)
according to the following list:
1.4.8 Note 2
1.5.8 Note 2
2.2.3 Note
2.3.2.1 Note 2
2.7.1 Note
3.2.1.1 Note
4.3.6 Note 1 & 2
4.7.3.1Note 2
6
Note 2 & 5
6.2.2 Note
7.1
Note 3
G.2.1 Note 2
General
(A1:2010)
General
(A2:2013)
1.5.1
1.5.9.4
2.2.4
2.3.4
2.10.3.2
3.2.4
4.7
5.1.7.1
6.1.2.1
6.2.2.1
7.2
Annex H
Note 2 & 3 1.5.7.1
Note
Note
1.7.2.1
Note 4, 5 & 6
Note
2.3.2
Note
Note 2
2.6.3.3
Note 2 & 3
Note 2
2.10.5.13
Note 3
Note 3.
2.5.1
Note 2
Note 4
4.7.2.2
Note
Note 3 & 4 5.3.7
Note 1
Note 2
6.1.2.2
Note
Note 2
6.2.2.2
Note
Note
7.3
Note 1 & 2
Note 2
Delete all the “country” notes in the reference document (IEC 609501:2005/A1:2010) according to the following list:
1.5.7.1
Note
6.2.2.1
Note 2
N/A
6.1.2.1
N/A
Note 2
EE.3
Note
Delete all the “country” notes in the reference document (IEC 609501:2005/A2:2013) according to the following list:
2.7.1
Note *
2.10.3.1
Note 2
N/A
6.2.2.
Note
* Note of secretary: Text of Common Modification remains unchanged.
1.1.1
(A1:2010)
Rev 2.0
Replace the text of NOTE 3 by the following.
NOTE 3 The requirements of EN 60065 may also be used to meet safety requirements for multimedia
equipment. See IEC Guide 112, Guide on the safety of multimedia equipment. For television sets EN
60065 applies.
Page 37 of 73
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
1.3.Z1
Add the following subclause:
Result - Remark
Verdict
N/A
1.3.Z1 Exposure to excessive sound pressure
The apparatus shall be so designed and constructed
as to present no danger when used for its intended
purpose, either in normal operating conditions or
under fault conditions, particularly providing
protection against exposure to excessive sound
pressures from headphones or earphones.
NOTE Z1 A new method of measurement is described in
EN 50332-1, Sound system equipment:
Headphones and earphones associated with portable
audio equipment - Maximum sound pressure level
measurement methodology and limit considerations - Part
1: General method for “one package equipment”, and in
EN 50332-2, Sound system equipment: Headphones and
earphones associated with portable audio equipment Maximum sound pressure level measurement
methodology and limit considerations - Part 2: Guidelines
to associate sets with headphones coming from different
manufacturers.
(A12:2011)
In EN 60950-1:2006/A12:2011
N/A
Delete the addition of 1.3.Z1 / EN 60950-1:2006
Delete the definition 1.2.3.Z1 / EN 60950-1:2006
/A1:2010
1.5.1
(Added
info*)
1.7.2.1
Add the following NOTE:
P
NOTE Z1 The use of certain substances in electrical and
electronic equipment is restricted within the EU: see
Directive 2002/95/EC.
New Directive 2011/65/11 *
N/A
(A1:2010)
In addition, for a PORTABLE SOUND SYSTEM, the
instructions shall include a warning that excessive
sound pressure from earphones and headphones can
cause hearing loss.
1.7.2.1
In EN 60950-1:2006/A12:2011
N/A
(A12.2011)
Delete NOTE Z1 and the addition for Portable Sound
System.
Add the following clause and annex to the existing
standard and amendments.
Zx Protection against excessive sound pressure from personal music
players
Rev 2.0
Page 38 of 73
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
N/A
Zx.1 General
This sub-clause specifies requirements for
protection against excessive sound pressure from
personal music players that are closely coupled to
the ear. It also specifies requirements for
earphones and headphones intended for use with
personal music players.
A personal music player is a portable equipment for
personal use, that:
is designed to allow the user to listen to
recorded or broadcast sound or video; and
primarily uses headphones or earphones that can
be worn in or on or around the ears; and
allows the user to walk around while in use.
NOTE 1 Examples are hand-held or body-worn portable CD
players, MP3 audio players, mobile phones with MP3 type
features, PDA’s or similar equipment.
A personal music player and earphones or
headphones intended to be used with personal
music players shall comply with the requirements of
this sub-clause.
The requirements in this sub-clause are valid for
music or video mode only.
The requirements do not apply:
while the personal music player is connected to
an external amplifier; or
while the headphones or earphones are not used.
NOTE 2 An external amplifier is an amplifier which is not part of
the personal music player or the listening device, but which is
intended to play the music as a standalone music player.
The requirements do not apply to:
hearing aid equipment and professional
equipment;
NOTE 3 Professional equipment is equipment sold through
special sales channels. All products sold through normal
electronics stores are considered not to be professional
equipment.
Rev 2.0
Verdict
Page 39 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
analogue personal music players (personal
music players without any kind of digital
processing of the sound signal) that are brought
to the market before the end of 2015.
Verdict
N/A
NOTE 4 This exemption has been allowed because this
technology is falling out of use and it is expected that within a
few years it will no longer exist. This exemption will not be
extended to other technologies.
For equipment which is clearly designed or
intended for use by young children, the limits of EN
71-1 apply.
N/A
Zx.2 Equipment requirements
No safety provision is required for equipment that
complies with the following:
equipment provided as a package (personal music
player with its listening device), where
the acoustic output LAeq,T is ≤ 85 dBA
measured while playing the fixed “programme
simulation noise” as described in EN 50332-1;
and
a personal music player provided with an
analogue electrical output socket for a listening
device, where the electrical output is ≤ 27 mV
measured as described in EN 50332-2, while
playing the fixed “programme simulation noise”
as described in EN 50332-1.
NOTE 1 Wherever the term acoustic output is used in this
clause, the 30 s A-weighted equivalent sound pressure level
LAeq,T is meant. See also Zx.5 and Annex Zx.
All other equipment shall:
a) protect the user from unintentional acoustic
outputs exceeding those mentioned above; and
b) have a standard acoustic output level not
exceeding those mentioned above, and
automatically return to an output level not
exceeding those mentioned above when the
power is switched off; and
Rev 2.0
Page 40 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
c) provide a means to actively inform the user of
the increased sound pressure when the
equipment is operated with an acoustic output
exceeding those mentioned above. Any means
used shall be acknowledged by the user before
activating a mode of operation which allows for
an acoustic output exceeding those mentioned
above. The acknowledgement does not need to
be repeated more than once every 20 h of
cumulative listening time; and
NOTE 2 Examples of means include visual or audible signals.
Action from the user is always required.
NOTE 3 The 20 h listening time is the accumulative listening
time, independent how often and how long the personal music
player has been switched off.
d) have a warning as specified in Zx.3; and
e) not exceed the following:
1) equipment provided as a package (player
with Its listening device), the acoustic output
shall be ≤ 100 dBA measured while playing the
fixed “programme simulation noise” described
in EN 50332-1; and
2) a personal music player provided with an
analogue electrical output socket for a listening
device, the electrical output shall be ≤ 150 mV
measured as described in EN 50332-2, while
playing the fixed “programme simulation noise”
described in EN 50332-1.
For music where the average sound pressure (long
term LAeq,T) measured over the duration of the
song is lower than the average produced by the
programme simulation noise, the warning does not
need to be given as long as the average sound
pressure of the song is below the basic limit of 85
dBA. In this case T becomes the duration of the
song.
NOTE 4 Classical music typically has an average sound
pressure (long term LAeq,T) which is much lower than the average
programme simulation noise. Therefore, if the player is capable
to analyse the song and compare it with the programme
simulation noise, the warning does not need to be given as long
as the average sound pressure of the song is below the basic
limit of 85 dBA.
For example, if the player is set with the programme simulation
noise to 85 dBA, but the average music level of the song is only
65 dBA, there is no need to give a warning or ask an
acknowledgement as long as the average sound level of the
song is not above the basic limit of 85 dBA.
Rev 2.0
Page 41 of 73
Verdict
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
N/A
Zx.3 Warning
The warning shall be placed on the equipment, or
on the packaging, or in the instruction manual and
shall consist of the following:
the symbol of Figure 1 with a minimum height of
5 mm; and
the following wording, or similar:
“To prevent possible hearing damage, do not listen
at high volume levels for long periods.”
Figure 1 – Warning label (IEC 60417-6044)
Alternatively, the entire warning may be given
through the equipment display during use, when
the user is asked to acknowledge activation of the
higher level.
Zx.4 Requirements for listening devices (headphones and earphones)
N/A
Zx.4.1 Wired listening devices with analogue
input
N/A
With 94 dBA sound pressure output LAeq,T, the input
voltage of the fixed “programme simulation noise”
described in EN 50332-2 shall be ≥ 75 mV.
This requirement is applicable in any mode where
the headphones can operate (active or
passive), including any available setting (for
example built-in volume level control).
NOTE The values of 94 dBA – 75 mV correspond with 85dBA –
27 mV and 100 dBA – 150 mV.
Rev 2.0
Page 42 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Zx.4.2 Wired listening devices with digital input
Verdict
N/A
With any playing device playing the fixed
“programme simulation noise” described in EN
50332-1 (and respecting the digital interface
standards, where a digital interface standard exists
that specifies the equivalent acoustic level), the
acoustic output LAeq,T of the listening device shall be
≤ 100 dBA.
This requirement is applicable in any mode where
the headphones can operate, including any
available setting (for example built-in volume level
control, additional sound feature like equalization,
etc.).
NOTE An example of a wired listening device with digital input is
a USB headphone.
Zx.4.3 Wireless listening devices
N/A
In wireless mode:
with any playing and transmitting device playing
the fixed programme simulation noise described
in EN 50332-1; and
respecting the wireless transmission standards,
where an air interface standard exists that
specifies the equivalent acoustic level; and
with volume and sound settings in the listening
device (for example built-in volume level control,
additional sound feature like equalization, etc.)
set to the combination of positions that
maximize the measured acoustic output for the
abovementioned programme simulation noise,
the acoustic output LAeq,T of the listening device
shall be ≤ 100 dBA.
NOTE An example of a wireless listening device is a Bluetooth
headphone.
N/A
Zx.5 Measurement methods
Measurements shall be made in accordance with
EN 50332-1 or EN 50332-2 as applicable. Unless
stated otherwise, the time interval T shall be 30 s.
NOTE Test method for wireless equipment provided without
listening device should be defined.
Rev 2.0
Page 43 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
2.7.1
Replace the subclause as follows:
Verdict
P
Basic requirements
To protect against excessive current, short-circuits
and earth faults in PRIMARY CIRCUITS, protective
devices shall be included either as integral parts of
the equipment or as parts of the building
installation, subject to the following, a), b) and c):
a) except as detailed in b) and c), protective
devices necessary to comply with the requirements
of 5.3 shall be included as parts of the equipment;
b) for components in series with the mains input to
the equipment such as the supply cord, appliance
coupler, r.f.i. filter and switch, short-circuit and
earth fault protection may be provided by protective
devices in the building installation;
c) it is permitted for PLUGGABLE EQUIPMENT
TYPE B or PERMANENTLY CONNECTED
EQUIPMENT, to rely on dedicated overcurrent and
short-circuit protection in the building installation,
provided that the means of protection, e.g. fuses or
circuit breakers, is fully specified in the installation
instructions.
N/A
If reliance is placed on protection in the building
installation, the installation instructions shall so
state, except that for PLUGGABLE EQUIPMENT
TYPE A the building installation shall be regarded
as providing protection in accordance with the
rating of the wall socket outlet.
2.7.2
This subclause has been declared ‘void’.
N/A
3.2.3
Delete the NOTE in Table 3A, and delete also in
this table the conduit sizes in parentheses.
N/A
Rev 2.0
Page 44 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
3.2.5.1
Replace
Result - Remark
“60245 IEC 53” by “H05 RR-F”;
“60227 IEC 52” by “H03 VV-F or
H03 VVH2-F”;
“60227 IEC 53” by “H05 VV-F or
H05 VVH2-F2”.
Verdict
N/A
In Table 3B, replace the first four lines by the
following:
Up to and including 6 |
0,75 a) |
b)
Over 6 up to and including 10| (0,75)
1,0 |
Over 10 up to and including 16| (1,0) c) 1,5
|
In the conditions applicable to Table 3B delete the
words “in some countries” in condition a).
In NOTE 1, applicable to Table 3B, delete the
second sentence.
3.2.5.1
(A2:2013)
3.3.4
NOTE Z1
The harmonised code designations
corresponding to the IEC cord types are given in Annex ZD
N/A
In Table 3D, delete the fourth line: conductor sizes
for 10 to 13 A, and replace with the following:
N/A
Over 10 up to and including 16 | 1,5 to 2,5 | 1,5 to 4
|
Delete the fifth line: conductor sizes for 13 to 16 A
4.3.13.6
Replace the existing NOTE by the following:
(A1:2010)
NOTE Z1 Attention is drawn to:
N/A
1999/519/EC: Council Recommendation on the limitation
of exposure of the general public to electromagnetic
fields 0 Hz to 300 GHz, and
2006/25/EC: Directive on the minimum health and safety
requirements regarding the exposure of workers to risks
arising from physical agents (artifical optical radiation).
Annex H
Standards taking into account mentioned
Recommendation and Directive which demonstrate
compliance with the applicable EU Directive are indicated
in the OJEC.
N/A
Replace the last paragraph of this annex by:
N/A
At any point 10 cm from the surface of the
OPERATOR ACCESS AREA, the dose rate shall
not exceed 1 μSv/h (0,1 mR/h) (see NOTE).
Account is taken of the background level.
Replace the notes as follows:
NOTE These values appear in Directive 96/29/Euratom.
Delete NOTE 2.
Rev 2.0
Page 45 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
Bibliograph Additional EN standards.
y
⎯
ZA
⎯
NORMATIVE REFERENCES TO INTERNATIONAL PUBLICATIONS WITH
THEIR CORRESPONDING EUROPEAN PUBLICATIONS
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause
Requirement + Test
1.2.4.1
In Denmark, certain types of Class I appliances
(see 3.2.1.1) may be provided with a plug not
establishing earthing conditions when inserted into
Danish socket-outlets.
N/A
1.2.13.14
In Norway and Sweden, for requirements see
1.7.2.1 and 7.3 of this annex.
N/A
In Finland, Norway and Sweden, resistors
bridging BASIC INSULATION in CLASS I PLUGGABLE
EQUIPMENT TYPE A must comply with the
requirements in 1.5.7.1. In addition when a single
resistor is used, the resistor must withstand the
resistor test in 1.5.7.2.
N/A
1.5.8
In Norway, due to the IT power system used (see
annex V, Figure V.7), capacitors are required to be
rated for the applicable line-to-line voltage (230 V).
N/A
1.5.9.4
In Finland, Norway and Sweden, the third dashed
sentence is applicable only to equipment as
defined in 6.1.2.2 of this annex.
N/A
(A11:2009)
1.5.7.1
(A11:2009)
Rev 2.0
Result - Remark
Page 46 of 73
Verdict
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause
Requirement + Test
1.7.2.1
In Finland, Norway and Sweden, CLASS I
PLUGGABLE EQUIPMENT TYPE A intended for
connection to other equipment or a network shall, if
safety relies on connection to protective earth or if
surge suppressors are connected between the
network terminals and accessible parts, have a
marking stating that the equipment must be
connected to an earthed mains socket-outlet.
The marking text in the applicable countries shall
be as follows:
In Finland: "Laite on liitettävä suojakoskettimilla
varustettuun pistorasiaan"
In Norway: “Apparatet må tilkoples jordet
stikkontakt”
In Sweden: “Apparaten skall anslutas till jordat
uttag”
1.7.2.1
(A11:2009)
In Norway and Sweden, the screen of the cable
distribution system is normally not earthed at the
entrance of the building and there is normally no
equipotential bonding system within the building.
Therefore the protective earthing of the building
installation need to be isolated from the screen of a
cable distribution system.
It is however accepted to provide the insulation
external to the equipment by an adapter or an
interconnection cable with galvanic isolator, which
may be provided by e.g. a retailer.
The user manual shall then have the following or
similar information in Norwegian and Swedish
language respectively, depending on in what
country the equipment is intended to be used in:
Rev 2.0
“Equipment connected to the protective earthing of
the building installation through the mains
connection or through other equipment with a
connection to protective earthing – and to a cable
distribution system using coaxial cable, may in
some circumstances create a fire hazard.
Connection to a cable distribution system has
therefore to be provided through a device providing
electrical isolation below a certain frequency range
(galvanic isolator, see EN 60728-11).”
Page 47 of 73
Result - Remark
Verdict
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause
Requirement + Test
Result - Remark
NOTE In Norway, due to regulation for installations of cable
distribution systems, and in Sweden, a galvanic isolator shall
provide electrical insulation below 5 MHz. The insulation shall
withstand a dielectric strength of 1,5 kV r.m.s., 50 Hz or 60 Hz,
for 1 min.
Verdict
N/A
Translation to Norwegian (the Swedish text will also
be accepted in Norway):
“Utstyr som er koplet til beskyttelsesjord via
nettplugg og/eller via annet jordtilkoplet
utstyr – og er tilkoplet et kabel-TV nett, kan
forårsake brannfare. For å unngå dette skal det ved
tilkopling av utstyret til kabel-TV nettet installeres
en galvanisk isolator mellom utstyret og kabel- TV
nettet.”
Translation to Swedish:
”Utrustning som är kopplad till skyddsjord via jordat
vägguttag och/eller via annan
utrustning och samtidigt är kopplad till kabel-TV nät
kan i vissa fall medfőra risk főr
brand. Főr att undvika detta skall vid anslutning av
utrustningen till kabel-TV nät
galvanisk isolator finnas mellan utrustningen och
kabel-TV nätet.”
1.7.2.1
(A2:2013)
In Denmark, CLASS I PLUGGABLE EQUIPMENT
TYPE A intended for connection to other equipment
or a network shall, if safety relies on connection to
protective earth or if surge suppressors are
connected between the network terminals and
accessible parts, have a marking stating that the
equipment must be connected to an earthed mains
socket-outlet.
The marking text in Denmark shall be as follows:
In Denmark: “Apparatets stikprop skal tilsluttes en
stikkontakt med jord, som giver forbindelse til
stikproppens jord.”
Rev 2.0
Page 48 of 73
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause
Requirement + Test
1.7.5
In Denmark, socket-outlets for providing power to
other equipment shall be in accordance with the
Heavy Current Regulations, Section 107-2-D1,
Standard Sheet DK 1-3a, DK 1-5a or DK 1-7a,
when used on Class I equipment. For
STATIONARY EQUIPMENT the socket-outlet shall
be in accordance with Standard Sheet DK 1-1b or
DK 1-5a.
1.7.5
(A11:2009)
1.7.5
(A2:2013)
Result - Remark
Verdict
N/A
For CLASS II EQUIPMENT the socket outlet shall be in
accordance with Standard Sheet DKA 1-4a.
In Denmark, socket-outlets for providing power to
other equipment shall be in accordance with the DS
60884-2-D1:2011.
N/A
For class I equipment the following Standard
Sheets are applicable: DK 1-3a, DK 1-1c,
DK 1-1d, DK 1-5a or DK 1-7a, with the exception
for STATIONARY EQUIPMENT where the socketoutlets shall be in accordance with Standard Sheet
DK 1-1b, DK 1-1c, DK 1-1d or DK 1-5a.
Socket outlets intended for providing power to
Class II apparatus with a rated current of 2,5 A
shall be in accordance with DS 60884-2-D1
standard sheet DKA 1-4a. Other current rating
socket outlets shall be in compliance with by DS
60884-2-D1 Standard Sheet DKA 1-3a or
DKA
1-3b.
Justification
the Heavy Current Regulations, 6c
2.2.4
In Norway, for requirements see 1.7.2.1, 6.1.2.1
and 6.1.2.2 of this annex.
N/A
2.3.2
In Finland, Norway and Sweden there are
additional requirements for the insulation. See
6.1.2.1 and 6.1.2.2 of this annex.
N/A
2.3.4
In Norway, for requirements see 1.7.2.1, 6.1.2.1
and 6.1.2.2 of this annex.
N/A
2.6.3.3
In the United Kingdom, the current rating of the
circuit shall be taken as 13 A, not 16 A.
N/A
Rev 2.0
Page 49 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause
Requirement + Test
Result - Remark
2.7.1
In the United Kingdom, to protect against
excessive currents and short-circuits in the
PRIMARY CIRCUIT of DIRECT PLUG-IN
EQUIPMENT, tests according to 5.3 shall be
conducted, using an external protective device
rated 30 A or 32 A. If these tests fail, suitable
protective devices shall be included as integral
parts of the DIRECT PLUG-IN EQUIPMENT, so
that the requirements of 5.3 are met.
2.10.5.13
In Finland, Norway and Sweden, there are
additional requirements for the insulation, see
6.1.2.1 and 6.1.2.2 of this annex.
N/A
3.2.1.1
In Switzerland, supply cords of equipment having
a RATED CURRENT not exceeding 10 A shall be
provided with a plug complying with SEV 1011 or
IEC 60884-1 and one of the following dimension
sheets:
N/A
SEV 6532-2.1991 Plug Type 15
250/400 V, 10 A
3P+N+PE
SEV 6533-2.1991 Plug Type 11
250 V, 10 A
L+N
SEV 6534-2.1991 Plug Type 12
250 V, 10 A
L+N+PE
In general, EN 60309 applies for plugs for currents
exceeding 10 A. However, a 16 A plug and socketoutlet system is being introduced in Switzerland,
the plugs of which are according to the following
dimension sheets, published in February 1998:
SEV 5932-2.1998: Plug Type 25 , 3L+N+PE
230/400 V, 16 A
SEV 5933-2.1998:Plug Type 21, L+N, 250 V, 16A
SEV 5934-2.1998: Plug Type 23, L+N+PE 250 V,
16 A
Rev 2.0
Page 50 of 73
Verdict
P
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause
Requirement + Test
Result - Remark
3.2.1.1
In Denmark, supply cords of single-phase
equipment having a rated current not exceeding13
A shall be provided with a plug according to the
Heavy Current Regulations, Section 107-2-D1.
Verdict
N/A
CLASS I EQUIPMENT provided with socket-outlets
with earth contacts or which are intended to be
used in locations where protection against indirect
contact is required according to the wiring rules
shall be provided with a plug in accordance with
standard sheet DK 2-1a or DK 2-5a.
If poly-phase equipment and single-phase
equipment having a RATED CURRENT exceeding
13 A is provided with a supply cord with a plug, this
plug shall be in accordance with the Heavy Current
Regulations, Section 107-2-D1 or EN 60309-2.
3.2.1.1
(A2:2013)
In Denmark, supply cords of single-phase
equipment having a rated current not exceeding 13
A shall be provided with a plug according to DS
60884-2-D1.
CLASS I EQUIPMENT provided with socket-outlets
with earth contacts or which are intended to be
used in locations where protection against indirect
contact is required according to the wiring rules
shall be provided with a plug in accordance with
standard sheet DK 2-1a or DK 2-5a.
If a single-phase equipment having a RATED
CURRENT exceeding 13 A or if a poly-phase
equipment is provided with a supply cord with a
plug, this plug shall be in accordance with the
standard sheets DK 6-1a in DS 60884-2-D1 or
EN 60309-2.
Justification
the Heavy Current Regulations, 6c
Rev 2.0
Page 51 of 73
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause
Requirement + Test
Result - Remark
3.2.1.1
In Spain, supply cords of single-phase equipment
having a rated current not exceeding 10 A shall be
provided with a plug according to UNE 20315:1994.
Verdict
N/A
Supply cords of single-phase equipment having a
rated current not exceeding 2,5 A shall be provided
with a plug according to UNE-EN 50075:1993.
CLASS I EQUIPMENT provided with socket-outlets
with earth contacts or which are intended to be
used in locations where protection against indirect
contact is required according to the wiring rules,
shall be provided with a plug in accordance with
standard UNE 20315:1994.
If poly-phase equipment is provided with a supply
cord with a plug, this plug shall be in accordance
with UNE-EN 60309-2.
3.2.1.1
In the United Kingdom, apparatus which is fitted
with a flexible cable or cord and is designed to be
connected to a mains socket conforming to BS
1363 by means of that flexible cable or cord and
plug, shall be fitted with a ‘standard plug’ in
accordance with Statutory Instrument 1768:1994 The Plugs and Sockets etc. (Safety) Regulations
1994, unless exempted by those regulations.
N/A
NOTE ‘Standard plug’ is defined in SI 1768:1994 and
essentially means an approved plug conforming to BS
1363 or an approved conversion plug.
3.2.1.1
In Ireland, apparatus which is fitted with a flexible
cable or cord and is designed to be connected to a
mains socket conforming to I.S. 411 by means of
that flexible cable or cord and plug, shall be fitted
with a 13 A plug in accordance with Statutory
Instrument 525:1997 - National Standards Authority
of Ireland (section 28) (13 A Plugs and Conversion
Adaptors for Domestic Use) Regulations 1997.
N/A
3.2.4
In Switzerland, for requirements see 3.2.1.1 of this
annex.
N/A
3.2.5.1
In the United Kingdom, a power supply cord with
conductor of 1,25 mm2 is allowed for equipment
with a rated current over 10 A and up to and
including 13 A.
N/A
Rev 2.0
Page 52 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause
Requirement + Test
Result - Remark
3.3.4
In the United Kingdom, the range of conductor
sizes of flexible cords to be accepted by terminals
for equipment with a RATED CURRENT of over 10
A up to and including 13 A is:
Verdict
N/A
• 1,25 mm2 to 1,5 mm2 nominal cross-sectional
area.
4.3.6
In the United Kingdom, the torque test is
performed using a socket outlet complying with BS
1363 part 1:1995, including Amendment 1:1997
and Amendment 2:2003 and the plug part of
DIRECT PLUG-IN EQUIPMENT shall be assessed
to BS 1363: Part 1, 12.1, 12.2, 12.3, 12.9, 12.11,
12.12, 12.13, 12.16 and 12.17, except that the test
of 12.17 is performed at not less than 125 °C.
Where the metal earth pin is replaced by an
Insulated Shutter Opening Device (ISOD), the
requirements of clauses 22.2 and 23 also apply.
N/A
4.3.6
In Ireland, DIRECT PLUG-IN EQUIPMENT is
known as plug similar devices. Such devices shall
comply with Statutory Instrument 526:1997 National Standards Authority of Ireland (Section 28)
(Electrical plugs, plug similar devices and sockets
for domestic use) Regulations, 1997.
N/A
Rev 2.0
Page 53 of 73
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause
Requirement + Test
Result - Remark
5.1.7.1
In Finland, Norway and Sweden TOUCH
CURRENT measurement results exceeding 3,5 mA
r.m.s. are permitted only for the following
equipment:
• STATIONARY PLUGGABLE EQUIPMENT TYPE
A that
is intended to be used in a RESTRICTED
ACCESS LOCATION where equipotential bonding
has been applied, for example, in a
telecommunication centre; and
has provision for a permanently connected
PROTECTIVE EARTHING CONDUCTOR; and
is provided with instructions for the
installation of that conductor by a SERVICE
PERSON;
• STATIONARY PLUGGABLE EQUIPMENT TYPE
B;
• STATIONARY PERMANENTLY CONNECTED
EQUIPMENT.
Rev 2.0
Page 54 of 73
Verdict
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause
Requirement + Test
6.1.2.1
In Finland, Norway and Sweden, add the
following text between the first and second
paragraph of the compliance clause:
(A1:2010)
Result - Remark
If this insulation is solid, including insulation forming
part of a component, it shall at least consist of
either
two layers of thin sheet material, each of
which shall pass the electric strength test below, or
one layer having a distance through
insulation of at least 0,4 mm, which shall pass the
electric strength test below.
Alternatively for components, there is no distance
through insulation requirements for the insulation
consisting of an insulating compound completely
filling the casing, so that CLEARANCES and
CREEPAGE DISTANCES do not exist, if the
component passes the electric strength test in
accordance with the compliance clause below and
in addition
passes the tests and inspection criteria of
2.10.11 with an electric strength test of 1,5 kV
multiplied by 1,6 (the electric strength test of
2.10.10 shall be performed using 1,5 kV), and
is subject to ROUTINE TESTING for electric
strength during manufacturing, using a test voltage
of 1,5 kV.
Rev 2.0
Page 55 of 73
Verdict
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause
Requirement + Test
Result - Remark
It is permitted to bridge this insulation with an
optocoupler complying with 2.10.5.4 b).
Verdict
N/A
It is permitted to bridge this insulation with a
capacitor complying with EN 60384-14:2005,
subclass Y2.
A capacitor classified Y3 according to
EN
60384-14:2005, may bridge this insulation under
the following conditions:
the insulation requirements are satisfied by
having a capacitor classified Y3 as defined by EN
60384-14, which in addition to the Y3 testing, is
tested with an impulse test of 2,5 kV defined in EN
60950-1:2006, 6.2.2.1;
the additional testing shall be performed on
all the test specimens as described in
EN
60384-14:
the impulse test of 2,5 kV is to be performed
before the endurance
test in EN 60384-14, in
the sequence of tests as described in EN 6038414.
6.1.2.2
In Finland, Norway and Sweden, the exclusions
are applicable for PERMANENTLY CONNECTED
EQUIPMENT, PLUGGABLE EQUIPMENT TYPE B
and equipment intended to be used in a
RESTRICTED ACCESS LOCATION where
equipotential bonding has been applied, e.g. in a
telecommunication centre, and which has provision
for a permanently connected PROTECTIVE
EARTHING CONDUCTOR and is provided with
instructions for the installation of that conductor by
a SERVICE PERSON.
N/A
7.2
In Finland, Norway and Sweden, for requirements
see 6.1.2.1 and 6.1.2.2 of this annex.
N/A
The term TELECOMMUNICATION NETWORK in
6.1.2 being replaced by the term CABLE
DISTRIBUTION SYSTEM.
7.3
(A11:2009)
Rev 2.0
In Norway and Sweden, for requirements see
1.2.13.14 and 1.7.2.1 of this annex.
Page 56 of 73
N/A
Report No.: T1505073-051
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
Annex ZD
(informative)
IEC and CENELEC code designations for flexible cords
Type of flexible cord
Code designations
IEC
CENELEC
PVC insulated cords
Flat twin tinsel cord
60227 IEC 41
H03VH-Y
Light polyvinyl chloride sheathed flexible cord
60227 IEC 52
H03VV-F
H03VVH2-F
Ordinary polyvinyl chloride sheathed flexible cord
60277 IEC 53
H05VV-F
H05VVH2-F
Braided cord
60245 IEC 51
H03RT-F
Ordinary tough rubber sheathed flexible cord
60245 IEC 53
H05RR-F
Ordinary polychloroprene sheathed flexible cord
60245 IEC 57
H05RN-F
Heavy polychloroprene sheathed flexible cord
60245 IEC 66
H07RN-F
Rubber insulated and sheathed cord
60245 IEC 86
H03RR-H
Rubber insulated, crosslinked PVC sheathed cord
60245 IEC 87
H03RV4-H
Crosslinked PVC insulated and sheathed cord
60245 IEC 88
H03V4V4-H
Rubber insulated cords
Cords having high flexibility
Rev 2.0
Page 57 of 73
Report No.: T1505073-051
1.5.1
P
TABLE: list of critical components
object/part No.
manufacturer/
trademark
type/model
technical data
standard
mark(s) of
conformity1)
Power plug
Shenzhen
HongPu
Electron Co.,
Ltd.
XTH-006
250Vac, 2.5A
EN 50075
VDE
Power cord
Shenzhen
Baohing
Electric Wrie &
Cable
Manufacture
Co., Ltd.
H03VVH2-F
2 x 0.75 mm²
IEC 60227
VDE
Power plug
Shenzhen
Wang Jing
Electrical Co.,
Ltd.
WJP-205
250Vac, 10A
AS/NZS 3112
N20410
Power cord
Shenzhen
Baohing
Electric Wrie &
Cable
Manufacture
Co., Ltd.
LTSA-2F
2 x 0.75 mm²
AS/NZS 4417
NSW14586
Plastic
Enclosure
SABIC
INNOVATIVE
PLASTICS US
L LC
C6200(GG)
V-0, 75°C, min. UL 94
thickness 1.5
mm
UL
PCB
Interchangeabl
e
Interchangeabl
e
V-1 or better
min. 130°C
UL 796
UL
Fuse (F1)
Dongguan
Better
Electronic
Technology
Co., Ltd
332
T1A, 250Vac
UL 248-1
UL
Shenzhen
3K
Lanson
Electronics Co.,
Ltd
T1A, 250Vac
IEC/EN 60127- VDE
1,
IEC/EN 601273
SHANTOU
MPX
HIGH-NEW
TECHNOLOGY
Max. 0.1μF,
min. 250Vac,
X2 type, min.
IEC/EN 60334- VDE
14
For EU plug
For AU plug
X –cap
Rev 2.0
Page 58 of 73
Report No.: T1505073-051
DEVELOPMNT
ZONE
SONGTIAN
ENTERPRISW
CO LTD
100°C
Shenzhen Su
MPX
Rong Electronic
Co., Ltd
Max. 0.1μF,
min. 250Vac,
X2 type, min.
100°C
IEC/EN 60334- VDE
14
Tenta Electric
Industrial Co.,
Ltd
MEX
Max. 0.1μF,
min. 250Vac,
X2 type, min.
100°C
IEC/EN 60334- VDE
14
Bleeder resistor Interchangeabl
(R1, R2)
e
Interchangeabl
e
Min. 1Mohm,
min. 1/2W
--
Tested with
appliance
Bridge diode
(D1, D2, D3,
D4)
Interchangeabl
e
Interchangeabl
e
Min. 0.5A, min.
500V
--
Tested with
appliance
Electrolytic
Interchangeabl
capacitors (C2) e
Interchangeabl
e
33μF, min.
400V, 105°C
--
Tested with
appliance
Chock (LF1)
UU9.8
Min. 130°C
--
Tested with
appliance
Transistor (Q1) Interchangeabl
e
Interchangeabl
e
Min. 0.8A, min.
500V
--
Tested with
appliance
Current sense
resistor (R12)
Interchangeabl
e
Interchangeabl
e
Min. 0.56ohm,
min. 1/2W
--
Tested with
appliance
Y-Capacitor
(CY1) Y1 type
Shantou HighNew
Technology
Developmnt
Zone Songtian
Enterprise
Co.,Ltd
CD Series
2200 pF, 400
Vac, min. 85°C
IEC/EN 60384- VDE
14
Current Sensor Shenzhen
Resistor (R23) Teruixiang
Electronic Co.,
Ltd
TY-Series
Current Sensor Interchangeabl
Resistor (R22) e
Interchangeabl
e
Min. 0.22ohm,
min. 1/2W
--
Opto-coupler
(U2)
PC817
Dti. =0.7mm,
Int. dcr.
>5.0mm, Ext.
dcr. = 8.0mm,
EN 60747-5-2, TUV
IEC/EN 609501
Rev 2.0
SHENZHEN
HSJ
ELECTRONIC
S CO.TLD
Sharp Corp
Y1 type.
2200pF, min.
400 Vac min.
85 °C.
IEC/EN 60384- VDE
14
Y1 type.
Page 59 of 73
Tested with
appliance
Report No.: T1505073-051
110°C
Transformer
(T1)
SHENZHEN
HSJ
ELECTRONIC
S CO.TLD
EE25
Pri. Winding:
--
Test with appliance
UL
N1(4-1)
Ф0.2mm*48Ts,
N3(1-5)
Ф0.2mm*48Ts
N4(2-3)
Ф0.15mm*19Ts
Sec. Winding:
N2(A-B)
Ф0.5mm*2P*13
Ts; Class B
- Bobbin
CHANG CHUN T375J
PLASTICS CO
LTD
Phenolic, V-0,
150°C, min.
thickness
0.71mm.
UL 94
- Triple
insulation wire
E&B
E&B-XXXB
TECHNOLOGY
CO LTD
130°C
IEC/EN 60950- VDE
1
- Insulation
Tape
JINGJIANG
YAHUA
PRESSURE
SENSITIVE
GLUE CO LTD
130°C
UL 510
UL
T1
Shenzhen Jun EE25
meijia
electronics co.,
LTD
Pri. Winding:
--
Test with appliance
UL
(Alternative)
CTI
N1(4-1)
Ф0.2mm*48Ts,
N3(1-5)
Ф0.2mm*48Ts
N4(2-3)
Ф0.15mm*19Ts
Sec. Winding:
N2(A-B)
Ф0.5mm*2P*13
Ts; Class B
- Bobbin
CHANG CHUN T375J
PLASTICS CO
LTD
Phenolic, V-0,
150°C, min.
thickness
0.71mm.
UL 94
- Triple
insulation wire
FURUKAWA
TEX-E
ELECTRIC CO
LTD
JINGJIANG
CTI
YAHUA
PRESSURE
130°C
IEC/EN 60950- VDE
1
130°C
UL 510
- Insulation
Tape
Rev 2.0
Page 60 of 73
UL
Report No.: T1505073-051
SENSITIVE
GLUE CO LTD
Note:
Rev 2.0
Page 61 of 73
Report No.: T1505073-051
1.6.2
P
TABLE: Electrical data (in normal conditions)
U (V/Hz)
I (A)
Irated (A)
P (W)
Fuse #
Ifuse (A)
198/50
--
0.166
19.17
F1
0.166
Maximum normal load(8.4Vdc,
2A)
198/60
--
0.164
19.14
F1
0.164
Maximum normal load(8.4Vdc,
2A)
220/50
0.35
0.156
19.18
F1
0.156
Maximum normal load(8.4Vdc,
2A)
220/60
0.35
0.153
19.12
F1
0.153
Maximum normal load(8.4Vdc,
2A)
240/50
0.35
0.146
19.17
F1
0.146
Maximum normal load(8.4Vdc,
2A)
240/60
0.35
0.139
19.06
F1
0.139
Maximum normal load(8.4Vdc,
2A)
254.4/50
--
0.135
18.94
F1
0.135
Maximum normal load(8.4Vdc,
2A)
254.4/60
--
0.131
18.90
F1
0.131
Maximum normal load(8.4Vdc,
2A)
264/50
--
0.131
18.64
F1
0.131
Maximum normal load(8.4Vdc,
2A)
264/60
--
0.125
18.57
F1
0.125
Maximum normal load(8.4Vdc,
2A)
Condition/status
Supplementary information:
2.1.1.5 c)
1)
N/A
TABLE: max. V, A, VA test
Voltage (rated)
(V)
Current (rated)
(A)
Voltage (max.)
(V)
Current (max.)
(A)
VA (max.)
(VA)
--
--
--
--
--
supplementary information:
Under highest Rated Voltage.
2.1.1.5 c)
2)
N/A
TABLE: stored energy
Capacitance C (µF)
Voltage U (V)
Energy E (J)
--
--
--
supplementary information:
Rev 2.0
Page 62 of 73
Report No.: T1505073-051
2.1.1.7
N/A
TABLE: discharge test
Condition
τ calculated
τ measured
(s)
(s)
t u→ 0V
(s)
--
--
--
--
Comments
--
supplementary information:
2.2
P
TABLE: evaluation of voltage limiting components in SELV circuits
Component (measured between)
max. voltage (V)
(normal operation)
V peak
V d.c.
59.2
--
--
8.1
T1 Pin A- Pin B
After D8 to Pin B
Fault test performed on voltage limiting components
D8 Shorted
Voltage Limiting Components
-D8
Voltage measured (V) in SELV circuits
(V peak or V d.c.)
0 (shut down immediately)
supplementary information:
2.4.2
P
TABLE: limited current circuit measurement
Location
CY1 Secondary pin to Earth
Voltage
(V)
Current
(mA)
Freq.
(Hz)
Limit
(mA)
0.18
0.36
--
0.7
Comments
CY1=2200pF
supplementary information:
Capacitance of CY1= 2200pF
2.5
N/A
TABLE: limited power sources
Circuit output tested:
Measured Uoc (V) with all load circuits
disconnected:
--
conditions
--
Isc (A)
Meas.
Limit
Meas.
Limit
--
--
--
--
supplementary information:
Rev 2.0
VA
Page 63 of 73
Report No.: T1505073-051
2.10.2
P
Table: working voltage measurement
Location
RMS voltage (V)
Peak voltage (V) Comments
T1 pin 2 – pin A
233
400
T1 pin 3 – pin A
249
480
T1 pin 4 – pin A
218
340
T1 pin 5 – pin A
217
392
T1 pin 2 – pin B
222
360
T1 pin 3 – pin B
257
482
T1 pin 4 – pin B
218
352
T1 pin 5 – pin B
220
440
U2 pin1 – pin 3
218
356
U2 pin1 – pin 4
216
360
U2 pin2 – pin 3
216
358
U2 pin2 – pin 4
215
365
CY1
220
368
--
Maximum Vpeak and Vrms of
T1
supplementary information:
Test voltage: 240 V
Test frequency: 60 Hz
P
2.10.3 and TABLE: Clearance and creepage distance measurements
2.10.4
U peak
(V)
U r.m.s.
(V)
Required cl
(mm)
cl
(mm)
Required cr
(mm)
cr
(mm)
L and N before fuse (FR1)
420
250
1.5
3.5
2.5
3.5
Poles of fuse (FR1)
420
250
1.5
3.5
2.5
3.5
U2 secondary pin (10N) to
core of T1
482
257
4.2
5.3
5.2
5.3
PCB trace under T1
482
257
4.2
7.5
5.2
7.5
PCB trace under CY1
420
250
4.0
6.4
5.0
6.4
PCB trace under U2
420
250
4.0
6.0
5.0
6.0
Primary component to User
accessible part
420
250
4.0
10.0
5.0
10.0
Clearance (cl) and creepage
distance (cr) at/of/between:
supplementary information:
1. Core of transformer T1 is considered as primary circuit.
Rev 2.0
Page 64 of 73
Report No.: T1505073-051
2.10.5
P
TABLE: Distance through insulation measurements
U peak
(V)
U rms
(V)
Test
voltage
(V)
Required DTI
(mm)
DTI
(mm)
Enclosure
420
250
3000
0.4
2.0
Opto-coupler
420
250
3000
0.4
0.4
Distance through insulation (DTI) at/of:
Supplementary information:
4.3.8
N/A
TABLE: Batteries
The tests of 4.3.8 are applicable only when appropriate battery
data is not available
--
N/A
Is it possible to install the battery in a reverse polarity position?
--
N/A
Non-rechargeable batteries
Discharging
Meas.
current
Manuf.
Specs.
Max.
current
during
normal
condition
--
--
Max.
current
during
fault
condition
--
--
Rechargeable batteries
Unintentional
charging
Charging
Discharging
Meas.
current
Manuf.
Specs.
Meas.
current
Manuf.
Specs.
--
--
--
--
--
--
--
--
Reversed
charging
Manuf.
Specs.
--
Meas.
current
--
--
--
--
--
Test results:
--
Verdict
- Chemical leaks
--
--
- Explosion of the battery
--
--
- Emission of flame or expulsion of molten metal
--
--
- Electric strength tests of equipment after completion of tests
--
--
Supplementary information:
4.3.8
N/A
TABLE: Batteries
Battery category .......................................... : (Lithium, NiMh, NiCad, Lithium Ion …)
Manufacturer ............................................... : -Type / model ............................................... : -Voltage ........................................................ : -Rev 2.0
Page 65 of 73
Report No.: T1505073-051
Capacity ...................................................... : -Tested and Certified by (incl. Ref. No.)....... : -Circuit protection diagram:
--
MARKINGS AND INSTRUCTIONS (1.7.2.1, 1.7.13)
--
Location of replaceable battery
Language(s) ……………………………………: -Close to the battery…………………………….: -In the servicing instructions……………………: -In the operating instructions…………………..: -4.5
P
TABLE: Thermal requirements
Supply voltage (V) ........................
198 V, 50 Hz
264 V, 50 Hz
⎯
Ambient Tmin (°C) ..........................
⎯
Ambient Tmax (°C).......................... --
⎯
Allowed
Tmax
(°C)
T (°C)
Maximum measured temperature T of
part/at::
Input wire
54.9
50.5
80
C1 body
64.9
53.9
100
FL1 body
74.7
56.3
130
PCB near D1
72.8
54.0
130
C2 body
76.0
62.6
105
T1 coil
88.0
73.0
90
T1 core
87.1
73.0
90
PCB near Q1
69.8
61.1
130
U2 body
78.9
66.8
100
PCB near D9
88.3
70.4
130
CY1 body
78.3
64.5
85
Feeling warm piece
65.2
50.8
--
Enclosure inside near T1
74.6
62.8
75
Rev 2.0
Page 66 of 73
Report No.: T1505073-051
Enclosure outside near T1
59.2
52.3
75
Ambient
35.0
35.0
--
Supplementary information:
Temperature T of winding:
t1 (°C)
R1 (Ω)
t2 (°C)
R2 (Ω)
T (°C)
Allowed
Tmax (°C)
Insulatio
n class
--
--
--
--
--
--
--
--
-Supplementary information:
--
--
--
--
--
--
--
4.5.5
N/A
TABLE: Ball pressure test of thermoplastic parts
Allowed impression diameter (mm) ......................: ≤ 2 mm
Part
⎯
Test temperature Impression diameter
(mm)
(°C)
--
--
--
Supplementary information: The bobbin of transformer material is phenolic, no test is needed.
P
4.6.1, 4.6.2 Table: enclosure openings
Location
Size (mm)
Comments
Bottom
Numerous rectangular
openings provided. Each
measured maximum
0.8mm x 5.0mm
--
Note(s): No openings.
4.7
P
TABLE: Resistance to fire
Part
Manufacturer of
material
Plastic Enclosure
SABIC
PCB
--
Type of material
C6200(GG)
--
Thickness Flammability
(mm)
class
Evidence
Min.
1.5mm
V-0
Yes
--
V-1 or better
Yes
Supplementary information:
5.1
P
TABLE: touch current measurement
Measured between:
Measured
(mA)
Limit
(mA)
Comments/conditions
L→Output connector
0.15
0.25
System ON
N→ Output connector
0.15
0.25
System ON
L→ Enclosure
0.01
0.25
System ON
Rev 2.0
Page 67 of 73
Report No.: T1505073-051
0.01
N→ Enclosure
0.25
System ON
supplementary information:
Test voltage: 264 V
Test frequency: 60 Hz, CY1=2200pF
5.2
P
TABLE: Electric strength tests, impulse tests and voltage surge tests
Voltage shape Test voltage Breakdown
(AC, DC,
(V)
Yes / No
impulse, surge)
Test voltage applied between:
L and N of input (without fuse)
AC
1500
No
Primary and secondary(for unit)
DC
4242
No
Primary and enclosure(cover with metal foil)
AC
3000
No
Transformer primary and secondary
AC
3000
No
Transformer primary with core to secondary
AC
3000
No
One layer insulation tape of T1 (all sources)
AC
3000
No
Supplementary information:
Core of transformer considered as primary part.
5.3
P
TABLE: Fault condition tests
Ambient temperature (°C).................................... :
25°C if not specified
⎯
Power source for EUT: Manufacturer, model/type,
output rating ........................................................ :
--
⎯
Component
No.
Fault
Supply
voltage
(V)
Test
time
Fuse #
Fuse
current
(A)
Observation
D1
s-c
240
1 sec
F1
0.139 Fuse open, D4 damage, no
-> 0
hazard.
C2
s-c
240
1 sec
F1
0.139 Fuse open, no hazard.
-> 0
Q1 pin G –
pin S
s-c
240
10 min
F1
0.139 >0.01
Q1 pin G –
pin D
s-c
240
1 sec
F1
0.139 -> Fuse open, Q1,D4, D1 damage,
0
no hazard.
Q1 pin D –
pin S
s-c
240
1 sec
F1
0.139 -> Fuse open, R12 damage, no
0
hazard.
R12
s-c
240
1 sec
F1
0.139 -> Fuse open, Q1 damage, no
0
hazard.
U1 pin 5 –pin
1
s-c
240
10 min
F1
0.139 >0.01
Rev 2.0
Page 68 of 73
Unit shut down immediately, no
hazard, no damage
Unit shut down immediately, no
hazard, no damage.
Report No.: T1505073-051
U1 pin 5 –pin
2
s-c
240
10 min
F1
0.139 >0.01
Unit shut down immediately, no
hazard, no damage.
U2 pin 3 –pin
4
s-c
240
10 min
F1
0.139 >0.01
Unit shut down immediately, no
hazard, no damage.
U2 pin 1 –pin
2
s-c
240
10 min
F1
0.139 >0.01
Unit shut down immediately, no
hazard, no damage.
U2 pin 3
o-c
240
10 min
F1
0.139 >0.01
Unit shut down immediately, no
hazard, no damage.
U2 pin 1
o-c
240
10 min
F1
0.139 >0.01
Unit shut down immediately, no
hazard, no damage.
T1 pin 1 to
pin 2
s-c
240
10 min
F1
0.139 >0.007
Unit shut down immediately, no
hazard, no damage.
T1 pin 3 – pin
4
s-c
240
10 min
F1
0.139 >0.01
Unit shut down immediately, no
hazard, no damage.
T1 pin 5 to
pin 6
s-c
240
10 min
F1
0.139 >0.01
Unit shut down immediately, no
hazard, no damage.
Output
s-c
240
10 min
F1
0.139 >0.01
Unit shut down immediately, no
damage, no hazard.
Supplementary information:
1) s-c = short circuit; o-l = overload.
Rev 2.0
Page 69 of 73
Report No.: T1505073-051
C.2
TABLE: transformers
Loc.
Tested insulation
P
Working
voltage
peak / V
Working
voltage
rms / V
Required
electric
strength
Required
clearance /
mm
(2.10.2)
(2.10.2)
(5.2)
(2.10.3)
Required
creepage
distance /
mm
(2.10.4)
Required
distance
thr. insul.
(2.10.5)
Primary
winding to
secondary
winding
RI
482
257
3000Vac 4.2
5.2
0.4
Core to
primary
winding
RI
482
257
3000Vac 4.2
5.2
0.4
Loc.
Tested insulation
Test
voltage/
V
Measured
creepage
dist./ mm
Measured
distance
thr. insul. /
mm;
number of
layers
Primary
winding to
secondary
winding
RI
3000Vac
6.0
6.0
TIW wire
and two
layers
insulation
tape used
Core to
primary
winding
RI
3000Vac
6.0
6.0
TIW wire
and two
layers
insulation
tape used
supplementary information:
Transformer core considered as primary.
Rev 2.0
Page 70 of 73
Measured
clearance /
mm
Report No.: T1505073-051
Photo(s)
Rev 2.0
Page 71 of 73
Report No.: T1505073-051
Photo(s)
Rev 2.0
Page 72 of 73
Report No.: T1505073-051
Photo(s)
END OF THIS REPORT
Rev 2.0
Page 73 of 73
Atttachment 1
National Differences
Report No.: T1505073-051
IEC60950_1F - ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
ATTACHMENT TO TEST REPORT IEC 60950-1
AUSTRALIA and NEW ZEALAND NATIONAL DIFFERENCES
Information technology equipment – Safety –
Part 1: General requirements
Differences according to................:
AS/NZS 60950.1:2011 Amendment 1:2012
Annex ZZ Variations
1.2
Between the definitions for "Person, service" and
"Range, rated frequency" insert the following:
Potential ignition source
Inserted.
P
1.2.12
1.2.12.201
Insert a new Clause 1.2.12.201 after Clause
Added.
1.2.12.15 as follows:
1.2.12.201
POTENTIAL IGNITION SOURCE
Possible fault which can start a fire if the opencircuit voltage measured across an interruption or
faulty contact exceeds a value of 50 V (peak) a.c.
or d.c. and the product of the peak value of this
voltage and the measured r.m.s. current under
normal operating conditions exceeds 15 VA.
Such a faulty contact or interruption in an
electrical connection includes those which may
occur in CONDUCTIVE PATTERNS on
PRINTED BOARDS.
NOTE 201 An electronic protection circuit may be
used to prevent such a fault from becoming a
POTENTIAL IGNITION SOURCE.
NOTE 202 This definition is from AS/NZS
60065:2003.
P
1.5.1
1. Add the following to the end of the first
paragraph:
‘or the relevant Australian/New Zealand
Standard.’
2. In NOTE 1, add the following after the word
‘standard’:
‘or an Australian/New Zealand Standard’
P
Page 1 of 10
Added.
Atttachment 1
National Differences
Report No.: T1505073-051
IEC60950_1F - ATTACHMENT
Clause
Requirement + Test
Result - Remark
1.5.2
Add the following to the end of first and third dash
items:
"or the relevant Australian/New Zealand
Standard."
3.2.5.1
Modify Table 3B as follows:
1. Delete the first four rows and replace with the
following:
Rated current
of equipment
A
Nominal
crosssectional
area mm2
AWG or kcmil
(cross-sectional
area in mm2)
see note 2
Over 0.2 up to
and including 3
0.5a
18 [0.8]
Over 3 up to
and including
7.5
0.75
16 [1.3]
Over 7.5 up to
and including
10
(0.75)b 1.00
16 [1.3]
Over 10 up to
and including
16
(1.0)c 1.5
14 [2]
2. Delete NOTE 1.
3. Delete Footnote a and replace with the
following:
a
This nominal cross-sectional area is only allowed
for Class II appliances if the length of the power
supply cord, measured between the point where
the cord, or cord guard, enters the appliance, and
the entry to the plug does not exceed 2 m (0,5
mm2 three-core supply flexible cords are not
permitted; see AS/NZS 3191).
Page 2 of 10
Verdict
N/A
Replaced.
Should be evaluated during
national approval.
P
Atttachment 1
National Differences
Report No.: T1505073-051
IEC60950_1F - ATTACHMENT
Clause
Requirement + Test
Result - Remark
4.1.201
Insert a new Clause 4.1.201 after Clause 4.1 as No such device.
follows:
4.1.201 Display devices used for television
purposes
Display devices which may be used for television
purposes, with a mass of 7 kg or more, shall
comply with the requirements for stability and
mechanical hazards, including the additional
stability requirements for television receivers,
specified in AS/NZS 60065.
N/A
4.3.6
Delete the third paragraph and replace with the
following:
Equipment with a plug portion, suitable for
insertion into a 10 A 3-pin flatpin socket-outlet
complying with AS/NZS 3112 shall comply with
the requirements in AS/NZS 3112 for equipment
with integral pins for insertion into socket-outlets.
No such device.
N/A
4.7
Add the following new paragraph to the end of
the clause:
For alternative tests refer to clause 4.7.201.
Added.
P
4.7.201
Insert a new Clause 4.7.201 after Clause 4.7.3.6
as follows:
4.7.201 Resistance to fire - Alternative tests
Added.
P
4.7.201.1
NOTE In considering how to minimize
propagation of fire and what ‘small parts’ are,
account should be taken of the cumulative effect
of small parts adjacent to each other for the
possible effect of propagating the fire from one
part to another.
Compliance shall be checked by the tests of
4.7.201.2, 4.7.201.3, 4.7.201.4 and 4.7.201.5.
For the base material of printed boards,
compliance shall be checked by the test of
4.7.201.5.
The tests shall be carried out on parts of nonmetallic material which have been removed from
the apparatus. When the glow-wire test is carried
out, the parts shall be placed in the same
orientation as they would be in normal use.
These tests are not carried out on internal wiring.
Page 3 of 10
Verdict
P
Atttachment 1
National Differences
Report No.: T1505073-051
IEC60950_1F - ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
General
Parts of non-metallic material shall be resistant to
ignition and spread of fire.
This requirement does not apply to decorative
trims, knobs and other parts unlikely to be ignited
or to propagate flames from inside the apparatus,
or the following:
(a) Components that are contained in an
enclosure having a flammability category of V-0
according to AS/NZS 60695.11.10 and having
openings only for the connecting wires filling the
openings completely, and for ventilation not
exceeding 1mm in width regardless of length.
(b) The following parts which would contribute
negligible fuel to a fire:
- small mechanical parts, the mass of which does
not exceed 4g, such as mounting parts, gears,
cams, belts and bearings;
- small electrical components, such as capacitors
with a volume not exceeding 1,750 mm3 ,
integrated circuits, transistors and optocoupler
packages, if these components are mounted on
material of flammability category V-1, or better,
according to AS/NZS 60695.11.10.
4.7.201.2
Testing of non-metallic materials
Parts of non-metallic material shall be subject to
the glow-wire test of AS/NZS 60695.2.11 which
shall be carried out at 550°C.
Parts for which the glow-wire test cannot be
carried out, such as those made of soft or foamy
material, shall meet the requirements specified in
ISO 9772 for category FH-3 material. The glowwire test shall be not carried out on parts of
material classified at least FH-3 according to ISO
9772 provided that the sample tested was not
thicker than the relevant part.
P
4.7.201.3
Testing of insulating materials
Parts of insulating material supporting
POTENTIAL IGNITION SOURCES shall be
subject to the glow-wire test of AS/NZS
60695.2.11 which shall be carried out at 750°C.
The test shall be also carried out on other parts
of insulating material which are within a distance
P
Page 4 of 10
Atttachment 1
National Differences
Report No.: T1505073-051
IEC60950_1F - ATTACHMENT
Clause
Requirement + Test
Result - Remark
of 3 mm of the connection.
NOTE Contacts in components such as switch
contacts are considered to be connections.
For parts which withstand the glow-wire test but
produce a flame, other parts above the
connection within the envelope of a vertical
cylinder having a diameter of 20 mm and a height
of 50 mm shall be subjected to the needle-flame
test. However, parts shielded by a barrier which
meets the needle-flame test shall not be tested.
The needle-flame test shall be made in
accordance with
Clause of AS /
NZS 60695.11.5
Change
9 Test procedure
9.2 Application
of needle flame
Replace the first paragraph
with:
The specimen shall be
arranged so that the flame
can be applied to a vertical
or horizontal edge as
shown in the examples of
figure 1. If possible the
flame shall be applied at
least 10 mm from a corner
Replace the second
paragraph with:
The duration of application
of the test flame shall be 30
s ±1 s.
9.3 Number of
test specimens
Replace with:
The test shall be made on
one specimen. If the
specimen does not
withstand the test, the test
may be repeated on two
further specimens, both of
which shall withstand the
test.
11 Evaluation of
test results
Replace with:
The duration of burning (tb)
shall not exceed 30 s.
However, for printed circuit
boards, it shall not exceed
Page 5 of 10
Verdict
Atttachment 1
National Differences
Report No.: T1505073-051
IEC60950_1F - ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
15 s.
The needle-flame test shall not be carried out on
parts of material classified as V-0 or V-1
according to AS/NZS 60695.11.10, provided that
the sample tested was not thicker than the
relevant part.
4.7.201.4
Testing in the event of non-extinguishing material Added.
If parts, other than enclosures, do not withstand
the glow-wire tests of 4.7.201.3, by failure to
extinguish within 30 s after the removal of the
glow-wire tip, the needle-flame test detailed in
4.7.201.3 is made on all parts of non-metallic
material which are within a distance of 50 mm or
which are likely to be impinged upon by flame
during the tests of 4.7.201.3. Parts shielded by a
separate barrier which meets the needle-flame
test need not to be tested.
NOTE 1 - If the enclosure does not withstand the
glow-wire test the equipment is considered to have
failed to meet the requirement of clause 4.7.201
without the need for consequential testing.
NOTE 2 - If other parts do not withstand the glowwire test due to ignition of the tissue paper and if
this indicates that burring or glowing particles can
fall onto an external surface underneath the
equipment, the equipment is considered to have
failed to meet the requirement of clause 4.7.201
without the need for consequential testing.
NOTE 3 - Parts likely to be impinged upon by the
flame are considered to be those within the
envelope of a vertical cylinder having a radius of
10 mm and a height equal to the height of the
flame, positioned above the point of the material
supporting in contact with or in close proximity to
connections.
Page 6 of 10
N/A
Atttachment 1
National Differences
Report No.: T1505073-051
IEC60950_1F - ATTACHMENT
Clause
Requirement + Test
Result - Remark
4.7.201.5
Added.
The base material of printed boards shall be
subjected to the needle-flame test of Clause
4.7.201.3. The flame shall be applied to the edge
of the board where the heat sink effect is lowest
when the board is positioned as in normal use.
The flame shall not be applied to an edge,
consisting of broken perforations, unless the
edge is less than 3 mm from a POTENTIAL
IGNITION SOURCE.
The test is not carried out if the —
- Printed board does not carry any POTENTIAL
IGNITION SOURCE;
- Base material of printed boards, on which the
available apparent power at a connection
exceeds 15 VA operating at a voltage exceeding
50 V and equal or less than 400 V (peak) a.c. or
d.c. under normal operating conditions, is of
flammability category V-1 or better according to
AS/NZS 60695.11.10, or the printed boards are
protected by an enclosure meeting the
flammability category V-0 according to AS/NZS
60695.11.10, or made of metal, having openings
only for connecting wires which fill the openings
completely; or
- Base material of printed boards, on which the
available apparatus power at a connection
exceeds 15 VA operating at a voltage exceeding
400 V(peak) a.c. or d.c. under normal operating
conditions, and base material of printed boards
supporting spark gaps which provides protection
against overvoltages, is of flammability category
V-0 according to AS/NZS 60695.11.10 or the
printed boards are contained in a metal
enclosure, having openings only for connecting
wires which fill the openings completely.
Compliance shall be determined using the
smallest thickness of the material.
NOTE Available apparent power is the maximum
apparent power which can be drawn from the
supplying circuit through a resistive load whose value
is chosen to maximise the apparent power for more
than 2 min when the circuit supplied is disconnected
Page 7 of 10
Verdict
N/A
Atttachment 1
National Differences
Report No.: T1505073-051
IEC60950_1F - ATTACHMENT
Clause
Requirement + Test
Result - Remark
6.2.2
For Australia only, delete the first paragraph and
Note, and replace with the following:
In Australia only, compliance with 6.2.2 shall be
checked by the tests of both 6.2.2.1 and 6.2.2.2.
No TNV.
N/A
6.2.2.1
No TNV.
For Australia only, delete the first paragraph
including the Notes, and replace with the
following:
In Australia only, the electrical separation is
subjected to 10 impulses of alternating polarity,
using the impulse test generator reference 1 of
Table
N.1. The interval between successive impulses is
60 s and the initial voltage, Uc, is:
(i) for 6.2.1 a): 7.0 kV for hand-held telephones
and for headsets and 2.5 kV for other equipment;
and
(ii) for 6.2.1 b) and 6.2.1 c): 1.5 kV.
NOTE 201 The 7 kV impulse simulates lightning
surges on typical rural and semi-rural network
lines.
NOTE 202 The value of 2.5 kV for 6.2.1 a) was
chosen to ensure the adequacy of the insulation
concerned and does not necessarily simulate
likely overvoltages.
N/A
6.2.2.2
For Australia only, delete the second paragraph
No TNV.
including the Note, and
replace with the following:
In Australia only, the a.c. test voltage is:
(i) for 6.2.1 a): 3 kV; and
(ii) for 6.2.1 b) and 6.2.1 c): 1.5 kV.
NOTE 201 Where there are capacitors across the
insulation under test, it is recommended that d.c.
test voltages are used.
NOTE 202 The 3 kV and 1.5 kV values have
been determined considering the lowfrequency
induced voltages from the power supply
distribution system.
N/A
Page 8 of 10
Verdict
Atttachment 1
National Differences
Report No.: T1505073-051
IEC60950_1F - ATTACHMENT
Clause
Requirement + Test
Result - Remark
7.3
Not connected to cable
Add the following before the first paragraph:
Equipment providing functions that fall only within distribution system.
the scope of AS/NZS 60065 and that incorporate
a PSTN interface, are not required to comply with
this Clause where the only ports provided on the
equipment, in addition to a coaxial cable
connection and a PSTN interface, are audio or
video ports and analogue or data ports not
intended to be used for telecommunications
purposes.
Annex P
Add the following Normative References:
AS/NZS 3191, Electric flexible cords
AS/NZS 3112, Approval and test specification—
Plugs and socket-outlets
Index
No asbestos be used.
1. Insert the following between ‘asbestos, not to
be used as insulation’ and ‘attitude see
orientation’:
AS/NZS
3112............................................................4.3.6
AS/NZS 3191................. ....... 3.2.5.1 (Table 3B)
AS/NZS
60064......................................................4.1.201
AS/NZS 60695.2.11........... 4.7.201.2, 4.7.201.3
AS/NZS 60695.11.10............ 4.7.201.1, 4.7.201.5
AS/NZS
60695.11.5....................................4.7.201.3
2. Insert the following between ‘positive
temperature coefficient (PTC) device’ and
‘powder’: potential ignition
source ......................................... 1.2.201,
4.7.201.3, 4.7.201.5
N/A
Appendix ZZ
(A1)
Delete the variation to Clause 4.3.13.5 and
replace with the following:
1 Add the following after each reference to ‘IEC
60825-1’:
‘or AS/NZS 60825.1’
2 Add the following after ‘IEC 60825-2’ in line two
of the first
paragraph:
‘or AS/NZS 60825.2’
N/A
Page 9 of 10
Added.
Verdict
N/A
P
Atttachment 1
National Differences
Report No.: T1505073-051
IEC60950_1F - ATTACHMENT
Clause
Requirement + Test
Result - Remark
Appendix ZZ, 1 Delete the following item from the ‘Index’
Index (A1)
clause:
AS/NZS 2211.1 ........ ............................. 4.3.13.5
2 Add the following two items after the item for
AS/NZS 60695.11.5:
AS/NZS 60825.1 .............. ................. 4.3.13.5.1
AS/NZS 60825.2 ......... ....................... 4.3.13.5.1
- End of National Difference -
Page 10 of 10
Verdict
N/A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement