HOMCOM 820-161CW 30" 1400W Freestanding Energy Efficient Electric Fireplace Heater User Guide

EN
N o
Icon
Popular Products for Home
Owner’s Manual
COMBINATION ELECTRIC FIREPLACE/HEATER
FOR RESIDENTIAL USE ONLY IN US & CA
WARRANTY VOID OUTSIDE US & CA
Table of Contents
Electric Firebox Instructions
Mantel Assembly Instructions
safety Information
IMPORTANT SAFETY INFORMATION
PLEASE READ ALL OF THE INFORMATION IN THIS OPERATING
MANUAL, INCLUDING ALL SAFETY, OPERATING, AND MAINTENANCE
INFORMATION. TO AVOID THE POTENTIAL RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, USERS SHOULD FOLLOW THE
DIRECTIONS AND WARNINGS IN THIS MANUAL.
1. Read all instructions before using this heater.
2. 00 not use this heater outdoors.
3. This heater is not intended for use in bathrooms, laundry areas
and similar indoor locations. Never locate the heater where it
may fall into a bathtub or other water container.
4. Do not run the power cord under carpeting. Do not cover the
power cord with throw rugs, runners, or the like. Arrange the
power cord away from traffic areas and where it will not be
tripped over.
5. To disconnect the heater, turn controls to off, then remove the
plug from the outlet.
6. Connect to properly grounded outlets only. Always plug heaters
directly into a wall outlet/receptacle. Never use with an
extension cord or reloadable power tap (outlet/power strip).
7. To prevent a possible fire, do not block firebox air intakes or
the exhaust in any manner. Do not operate the firebox on soft
surfaces, like a bed, where openings may become blocked.
8. There is a thermostat limiter inside the heater. When the inner
temperature over heats or abnormal heating occurs, the
thermostat protective device cuts off the power supply to avoid
fireplace damaged or risk of fire.
9. Use this heater only as described in this manual. Any other use
not recommended by the manufacturer may cause fire,
electrical shock, or injury to persons.
SAVE THESE INSTRUCTIONS
WARNING: There are no user serviceable parts inside the
fireplace/heater. If the unit appears to malfunction, turn the
unit off and unplug the unit from the wall immediately, and
contact Customer Service.
WARNING: This heater is hot when in use. To avoid burns, do
not let bare skin touch hot surfaces. If provided, use handles
when moving this heater. Keep combustible material, such as
furniture, pillows, bedding, papers, clothes and curtains at
least 3 ft. (0.9 meters) from the front of the heater and keep
them away from the sides and rear.
WARNING: Extreme caution is necessary when any heater is
used by or near children or invalids and whenever the heater
is left operating and unattended.
WARNING: Always unplug the heater when not in use.
WARNING: Do not operate any heater with a damaged cord or
plug or after the heater malfunctions, has been dropped or
damaged in any manner. Return the heater to an authorized
service facility for examination, electrical or mechanical
adjustment, or repair.
WARNING: Do not insert or allow foreign objects to enter any
ventilation or exhaust openings as this may cause an electric
shock or fire, or damage the heater.
PIP > PEP & Р
WARNING: A heater has hot and arching or sparking parts
inside. Do not use in areas where gasoline, paint, or
flammable liquids are used or stored.
>
CAUTION: While the heater is in use, the top center of the
fireplace can get hot to the touch, and may cause serious
injury or burns. Always supervise small children around the
fireplace/heater. Do not place any cloth or decorations over
the heater outlet of the fireplace, or otherwise obstruct the
heater outlet of the fireplace, as this may cause a fire and
serious injury may result.
safety Information (continued)
GROUNDING INSTRUCTIONS
DANGER: Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check with a
qualified electrician or serviceman if you are in doubt as to A
whether the product is properly grounded. Do not modify the
plug provided with the product. If it will not fit the outlet, have a
proper outlet installed by qualified electrician. O
This product must be grounded. If it should malfunction or Grounding Pin
breakdown, grounding provides a path of least resistance for Cover of Grounded Outlet Box——
electric current to reduce the risk of electric shock. This product is
equipped with a cord having an equipment-grounding conductor
and a grounding plug. The plug must be plugged into an appropriate ZA
outlet that is properly installed and grounded in accordance with all B
local codes and ordinances. Adapter 5,
This heater is for use on 120 volt circuits and has a grounded plug. : ñ 5
An adapter is available for connecting three-blade grounding type Grounding Lug = |
plugs to two-slot receptacles. The green grounding lug extending Metal Screw
from the adapter must be connected to a permanent ground such Cover of Grounded Outlet Bo—
as a properly grounded outlet box. The adapter should not be used
if a three-slot grounded receptacle is available.
Pre-installation
ELECTRICAL SPECIFICATIONS PACKAGE CONTENTS
o Voltage: 120 VAC, 60 Hz
o Watts: 1400 Watts
o PID: FP0089
TOOLS REQUIRED
Phillips
screwdriver
(not provided)
HARDWARE INCLUDED
A NOTE: Hardware not shown to actual size.
De y
Part Description Quantity
18 Screw 12 + 3 extra
Part Description Quantity
W Fireplace Insert 1
X Top Trim 1
Y Side Trim 2
This insert has front panel made of GLASS! ALWAYS use extreme caution when handling glass.
Failure to do so could result in personal injury or property damage.
A
Assembly
1 Attaching the metal trims
о Fasten the top trim (X) to the top of the fireplace insert (W) with two screws (18). Make sure that the right angle side points towards the front
of the unit.
o Align and attach two side trims (Y) to both sides of the fireplace insert (W) respectively with the right angle side facing the front of the unit,
using two screws (18) per trim.
_— 18
X | er:
183 >
—
gen y
18 — ‘ll!
|. = 18
y | -
18 N
> Installing the fireplace insert
o Carefully set the fireplace insert (W) into the back of the mantel and center it in the opening. Use care not to scratch the wood. Check the
alignment, and then attach the fireplace insert (W) to the mantel by inserting the screws (18) through the drilled holes on the trims (X and Y)
and securely screw into place using a Phillips screwdriver.
A NOTE: DO NOT attempt to install the insert from the front of the mantel - it will not fit.
Operation
о Read all instructions and warning prior to operating the appliance.
о Ensure that all controls are in the “OFF” position before plugging the appliance in to a properly grounded electrical outlet.
о The main control panel is located behind the cover at the top right corner on the front.
MI De
a
/{ [ioe NL
WEDD) EINEN (р)
N Right: Power ОМ / OFF
Left: Heater ON / OFF
Care and Maintenance
cleaning the heater. First turn off the main power. Then remove
N WARNING: Always disconnect from the power supply before
the electrical plug from the wall outlet.
WARNING: Do not use this fireplace insert if any part of it has
been under water. Immediately call a qualified service
technician to inspect the firebox and replace any part of the
electrical system which has been under water.
The blower motor and flame motor are pre-lubricated and need no further lubrication or maintenance. Use the soft brush attachment of a vacuum
cleaner to remove accumulation of dust or fluff from the outlet grille of the fan heater.
о Use a soft, clean cloth that will not scratch the surface when dusting.
Use a Clean soft cloth dampened with warm waiter to clean the fireplace surface. DO NOT use household or abrasive cleaners, as these
products may damage the surface.
a When cleaning the glass viewing screen use a non-abrasive damp cloth with liquid cleaner or soft soap if necessary; DO NOT use
cleaning powders or any other substance with abrasives since these substances will scratch glass.
Under no circumstances should this product be operated with a broken or chipped glass panel.
Do not strike or slam the glass.
о In the event that your appliance is stained or otherwise damaged during use, we recommend that you call a professional to repair your
furniture.
a When not in use please unplug the cord from the outlet to prevent any damage or accidental plug of the cord.
Troubleshooting
Problem
Solution
The unit does not turn on.
Check that the unit is plugged into a standard 120 V outlet.
Press the power button on the control panel.
The unit is on, but there is no flame effect.
Open the back panels to check if the flame spindle has fallen off
from the spindle motor.
There is a visible flame effect, but the heater does not blow warm
air.
Turn on/off the heater button several times to make sure it is in the
“ON” position.
The heater does not work, but the power and heater switches are
in the “ON” position.
Turn all switches to the “OFF” position and unplug the unit from the
wall outlet for 5 minutes. After 5 minutes plug the unit back into the
wall outlet, and operate as normal.
ASSEMBLY STEPS
PART IDENTIFICATION:
CODE DESCRIPTION QTY
1 Top Panel 1
2 Front Up Panel 1
3 Front Base Panel 1
4 Back Base Panel 1
5 Left Side Panel 1
6 Right Side Panel 1
/ Left Front Panel 1
8 Right Front Panel 1
9 Left Trim Panel 1
10 Right Trim Panel 1
11 Left Foot Panel 1
12 Right Foot Panel 1
13 Case Panel 2
Hardware Parts List:
CODE PICTURE DESCRIPTION QTY
A © Bolt 16
B Ly Plastic Connector 8
C o Metal Dowel 10
D Metal Cam 10
E XV, Wood Dowel 26
F “yp Screw 19
G % Metal Connector 2
H UD Plastic Cap 10
Touch-up pen
J = (Please use the enclosed touch-up pen 1
so instantly cover nicks and scratches
on the surface and edges.)
Assembly Tools Required:
OR
@
i. Ÿ
ш | nr A «=
Нех Кеу
Hand Drill (Included in the package)
|
z
Е
|
=>
у Е —-
2
o
Ч
Е
10
li
Th
11
001-877-644-9366
[email protected]