Scala Rider TeamSet Manual
SCALA RIDER® TeamSet™ |
1
English
User Guide
Gebrauchsanleitung
™
Guide d’Utilisation
Guida di Avvio
Guia de Usario
| SCALA RIDER® TeamSet™
2
SCALA RIDER® TeamSet™ |
CONTENTS OF RETAIL BOX
Congratulations, and thank you for choosing the SCALA RIDER
TeamSet Bluetooth® Headset package for Motorcycle helmets.
The retail box of the SCALA RIDER TeamSet contains two headset
units: one headset for the driver and a second headset for the
passenger:
The Driver’s unit includes a Bluetooth module that allows the
following uses:
1. Bluetooth headset for mobile phone communication*, supporting
Headset* and Handsfree* profiles (10m / 33 ft. range)
2. Transmitting GPS navigation instructions from a Bluetooth enabled
GPS device
3. Intercom communications Driver-Passenger – Full Duplex
(10m/33 ft. range)
4. MP3 Connectivity to an MP3 player
English
INTRODUCTION
Volume
Up
Two Headsets
Charging
Jack
Volume
Down
CTRL – Control Button
Intercom button
Left Speaker
(short cord)
Two Helmet Clamps
Right Speaker
(long cord)
The Passenger unit contains an intercom module and performs
the following uses only:
1. Intercom communications Passenger-Driver Full Duplex (10m/30 ft.
range)
2. MP3 connectivity to an MP3 player
Microphone
Tab
This manual will help you operate the headset, but you should first
familiarize yourself with the Bluetooth functionality of your mobile
phone and/or GPS device before using the Product.
Cardo wishes you an enjoyable and safe SCALA RIDER TeamSet
experience!
Back
Plate
Sliding Plate
NOTE: The use of
two speakers may be
illegal in certain jurisdictions. Please
check the local regulations and act
accordingly.
____________________
* Mobile phones that do not support the Bluetooth Handsfree profile may prevent you
from using the Redial and Call Reject features.
3
MP3
Jack
| SCALA RIDER® TeamSet™
SET UP AND CONFIGURATION
Wall Charger
Driver-to-Passenger
Full Duplex Intercom
Connection
(10 m/30 ft.)
2 Allen Wrenches
2 Sets of Velcro Pads
2 MP3 Cables
GPS
2 Glue Plates
Mobile Phone
2 Pre-moistened Towelettes
2 Carry-Pouches
MP3 Player
Driver and
Passenger
4 Microphone Sponges
Flat sponges for full-face helmets and round sponges for other helmet types
User Guide, including Warranty and Registration form
IMPORTANT:
SET UP FOR MOBILE PHONE CALLS
Your headsets are water-resistant devices, designed for use under
moderate rain or snow conditions. However, the headsets are not
waterproof and should not be used under severe weather conditions.
The cover tongue protecting the Charging Jack should be kept tightly
closed at all times to prevent moisture from entering the device.
If you have a Bluetooth enabled mobile phone and would like to
make and receive phone calls using the SCALA RIDER TeamSet
Driver’s unit, you must first pair your headset to the mobile phone.
Pairing is a one time process. Once the headset is paired to a
specific mobile phone during this Setup Procedure, they will
remain paired and automatically recognize each other whenever
they are within range. If the connection between the phone and
headset is lost, tap the CTRL button to reconnect the devices.
BEFORE USING (CHARGING THE
HEADSET)
Make sure that the headset is fully charged for at least four hours
before initial use.
1. Connect the wall charger to the headset’s Charging Jack (located
between the two Volume Buttons).
2. While charging, the Red Light turns on (it may take up to 15
seconds until the Red Light turns on). When charging is complete,
the Red Light will turn off.
TO PAIR THE SCALA RIDER TEAMSET TO A BLUETOOTH MOBILE
PHONE
1. Turn on your phone and make sure its Bluetooth function is
activated.
2. With the Driver’s unit headset turned OFF, press and hold
the CTRL Button until the Red and Blue Lights begin rapidly
alternating.
4
SCALA RIDER® TeamSet™ |
With some mobile phones, you may need to tap the CTRL button
to connect the headset to the phone after pairing is complete. The
SCALA RIDER TeamSet headset will automatically connect to the
last phone connected to the headset.
SET UP FOR BLUETOOTH GPS DEVICE
If you have a Bluetooth enabled GPS device and would
like to transmit navigation instructions and sounds
from the GPS device through the headset’s speakers,
please follow instructions described in section below
“TO PAIR THE SCALA RIDER TeamSet TO A Bluetooth GPS DEVICE”
If you want to use your mobile phone and your GPS device with the
SCALA RIDER TeamSet Driver’s unit headset, you should proceed as
follows:
1. Pair your GPS device to your mobile phone (Please consult your GPS
device’s User Manual for more information).
2. Pair your headset to the GPS device as described below.
PAIRING BETWEEN THE PASSENGER
AND DRIVER HEADSETS
The two headset units (Driver and Passenger units) are supplied factory paired. Therefore, you do not need to pair these devices. However,
if re-pairing is needed you may proceed as follows:
1. Make sure that both units are turned ON and close to each other.
2. Press the Intercom Buttons of both devices simultaneously for at least
10 seconds, the red Status Light of the passenger unit will light steadily.
3. If successful, the blue Status Light of the passenger unit will flash.
4. If pairing has failed, the red Status Light of the passenger unit will
turn off and you must repeat the procedure.
NOTE: Not all Bluetooth enabled GPS devices allow connections to
Bluetooth headsets like the SCALA RIDER TeamSet. Please consult
your GPS device’s User Manual for more information.
5
English
TO PAIR THE SCALA RIDER TEAMSET TO A BLUETOOTH GPS
DEVICE:
1. Turn on your GPS device.
2. With the Driver’s unit headset turned OFF, press and hold
the CTRL Button until the Red and Blue Lights begin rapidly
alternating.
3. Search for Bluetooth headsets on your GPS device by following
the device’s instructions. Please consult your GPS device’s User
Manual for more information.
4. If your GPS device prompts for a PIN or Passkey enter 0000
(four zeros).
5. Your GPS device will confirm that pairing has succeeded. The
headset will begin flashing slowly in Blue.
6. If you wish to use a Bluetooth mobile phone to make and
receive calls through the headset, you must now pair your
mobile phone to your GPS device by following your GPS and/
or mobile phone’s instructions.
NOTE: If the Pairing process is not completed within two
minutes the headset will return to Standby mode.
3. Search for Bluetooth devices on your phone by following the
phone’s instructions. Please consult your phone’s User Manual
for more information.
4. After a few seconds the phone will list the SCALA RIDER
TeamSet as a discovered device. Select it and follow your
phone’s instructions to accept the pairing.
5. When prompted enter 0000 (four zeros) as your PIN or passkey.
6. Your phone will confirm that pairing has succeeded and the
headset will begin flashing slowly in Blue.
NOTE: If the Pairing process is not completed within two minutes the
headset will return to Standby mode.
| SCALA RIDER® TeamSet™
ATTACHING THE CLAMP ON THE HELMET
NOTE: While we have no reason to believe that the gluing
option might negatively affect any helmet, Cardo
does not assume any responsibility to that affect, irrespective of its nature and circumstances. The Glue
Plate is offered as a free option that you may choose
to use at your own risk and subject to renouncement
of any future claims.
Perform this procedure for both the driver and the passenger helmets.
The Helmet Clamp must be attached to the left side of the helmet. Once
attached, the headset unit can be mounted or released from the Helmet
Clamp at any time.
There are two methods that can be used in order to attach the Clamp
onto the helmet:
Caution: This process can be done only once!
Standard Method: Recommended for most helmet types.
Glue Plate Method: Recommended for helmets to which the
standard method cannot be applied, using the Glue Plate included
in the box.
1. Use the enclosed Allen Wrench to remove both Allen screws
and release the Helmet Clamp’s back plate.
2. Determine the location on the helmet where the
Helmet Clamp must be attached.
Standard Method
1. Use the enclosed Allen Wrench to loosen the
two screws on the Back Plate.
3. Adjust the Helmet Clamp’s location on the Helmet so that
the microphone is located opposite the center of your mouth. You
may need to reposition the Clamp repeatedly until you identify the
best spot. The microphone must be positioned
vertically and not horizontally (Be sure to clean
the selected area prior to the gluing process as
described in # 4 below).
2. Slide the Back Plate between the internal padding
and the external shell of the helmet.
3. Adjust the clamp’s location so that the
microphone is located opposite center of
your mouth and then tighten the screws.
You may need to reposition the Clamp
repeatedly until you identify the best
spot. The microphone must be positioned
vertically and not horizontally.
4. Use the pre-moistened Towelette to clean the helmet area where
you want to install the Glue Plate. Allow to dry thoroughly.
5. Peel the foil cover from the Glue Plates’ adhesive pad.
6. Place the Glue Plate into position according to #3. Press firmly 15
seconds on all 3 parts of the Glue Plate.
7. The adhesive pad bonds to full strength over the next 24 hours.
Therefore it is recommended to not use the headset during this 24
hour period.
Glue Plate Method
You have the option to glue the Helmet Clamp onto your helmet, when
the above standard method cannot be used, or in case you prefer to
secure the Helmet Clamp with adhesive glue. This option has been
successfully used for a range of high end helmets.
8. Fasten the Clamp to the Glue Plate using the Allen screws that were
previously removed.
6
SCALA RIDER® TeamSet™ |
Attach the speakers to the Velcro
inside your helmet opposite your
ears (short speaker cord for the left
ear [A] and the long speaker cord [B]
for the right ear). You may want to
use the supplied Velcro pad.
Using two speakers inside the
helmet may be prohibited in certain
jurisdictions. If this is the case, you
should tuck away the long corded speaker
underneath the helmet padding as
follows: Lead the speaker cord [B]
alongside the rim of the padding to
the right side and then back to the left
side, near speaker [A]. Then place the
speaker [B] underneath the padding.
Speaker A
Speaker B
Press here
to remove
AUDIO SOURCES AND PRIORITIES
Cable
The different Audio Sources that are connected to the SCALA RIDER
TeamSet are prioritized as follows:
Highest: 1. Mobile phone audio (Incoming/outgoing calls) / GPS
device (GPS audio and navigation instructions)
2. Driver-to-Passenger Full Duplex Intercom Connection
Lowest 3. MP3 Connectivity
A high priority Audio Source will always interrupt any lower priority
Audio Source. i.e. Mobile phone call overrides Intercom calls.
Speaker
SpeakerA B
Speaker B
AUDIO SOURCES AND PRIORITIES – Passenger Unit
Passenger can also initiate intercom calls with drivers unit as well as
listen to music from his MP3 Player. Intercom call overrides the audio
from the MP3 player.
ATTACHING AND REMOVING THE
HEADSET FROM THE HELMET CLAMP
USING THE MP3 PLAYER WITH YOUR
HEADSET
ATTACHING:
Your SCALA RIDER headset can be connected to an MP3
player/audio device by simply plugging it to the Helmet
Clamp’s jack with the audio cable as follows:
Slide the headset downwards along
the sliding panel until a clicking sound
indicates that the headset is locked in
place.
7
English
REMOVING:
Your headset can be removed for
charging and storage by pressing your
finger gently against the tab and sliding
the headset up with the other hand.
We recommend that you remove the
headset from the helmet when not in
use.
POSITIONING THE SPEAKERS
| SCALA RIDER® TeamSet™
1. Power on the headset to have it on
Standby mode, flashing slowly in Blue.
2. Connect one side of the audio cable
to your MP3 player/audio device’s
jack and the other side to the helmet
Clamp’s jack as shown in the photo.
3. Operate the MP3 Player/audio device
by using its buttons (FF / REW / PLAY
/ PAUSE ).
INITIATING AND RECEIVING MOBILE
PHONE CALLS
Voice Recognition (VR)
The VR feature allows you to answer or reject incoming calls by voice
Control without having to remove your hands from the handlebars.
The default mode of this feature is ON (enabled).
Each time you switch off and turn on the headset, the VR feature will
be automatically enabled.
To disable / enable the VR feature see phone functions below.
Connect the audio cable to
the helmet Clamp’s jack
NOTE: Volume can only be adjusted through the MP3 Player. Any other
audio connection will automatically mute the MP3 Player. The
audio signal will return only when headset is once again in
Standby mode.
Note: The VR feature works well while driving up to 70km/h
or 44m/h with 3/4 helmet and up to 120km/h or 75m/h
with a closed full-faced helmet.
PHONE FUNCTIONS
DRIVER’S UNIT FUNCTIONS
USING THE HEADSET
G E N E R A L
DESIRED RESULT:
Turn on the
headset
Turn off the
headset
Increase volume
Decrease volume
F U N C T I O N S
REQUIRED ACTION:
Press the CTRL Button steadily for at least 6 seconds.
Led indication: three blue flashes.
Audio feedback: Ascending tone (low-high).
Press the CTRL Button steadily for at least 3 seconds.
Led indication: three red flashes.
Audio feedback: Descending tone (high-low).
Tap the Volume Up Button
Tap the Volume Down Button
Answer a call
Tap the CTRL Button or speak loudly any word of
your choice.
Reject a call
Tap the Intercom Button or remain silent for 15
seconds during an incoming call.
Terminate a call
Press and hold the Intercom Button for 3
seconds when a call is in progress. For some
mobile phones you may need to press the
Control button to end the call.
During Standby, tap the CTRL Button and state the
name of the person you wish to call. This feature
is supported only by mobile phones that support
the Voice Dial feature.
Voice Dial
Redial
Enable/Disable
voice command
feature
AGC (Automatic Gain Control): In addition to manual Volume Control,
the SCALA RIDER TeamSet will automatically increase and reduce its
volume according to ambient noise and driving speed.
8
During Standby, tap the Intercom Button
Long press the volume up and down buttons simultaneously until you hear a beep. The default status is
voice command enabled.
SCALA RIDER® TeamSet™ |
PASSENGER’S UNIT FUNCTIONS
USING THE HEADSET
INTERCOM FUNCTIONS–Driver’s Unit
G E N E R A L
DESIRED RESULT:
Start using the intercom
Terminate operation of
Intercom
Conference Call (add
passenger to an active call)
End Conference Call
(release passenger from a
conference call)
DESIRED RESULT:
Turn on the headset
F U N C T I O N S
REQUIRED ACTION:
During standby, start talking loudly to
activate the feature
Stop talking. The audio connection will be
terminated within 25 seconds.
During an active phone-call, tap the
intercom button.
During a conference call, tap the intercom
button.
Turn off the headset
Start using the Intercom
Terminate operation of
Intercom
Enable/disable Always-on
Intercom
Note: In case the person on the other side of the intercom is not responding and
you start talking, 2 beeps will alert you that the other side is not available
Increase Intercom volume
Decrease Intercom volume
STATUS LIGHTS
REQUIRED ACTION:
Press the CTRL Button steadily for at least 3
seconds. Led indication: three blue flashes.
Audio feedback: Ascending tone (low-high).
Press the CTRL Button steadily for at least 3
seconds. Led indication: three red flashes.
Audio feedback: Descending tone (high-low).
During standby, start talking loudly to
activate the Intercom
Stop talking. The audio connection will be
terminated within 25 seconds.
During standby tap the Control Button.
One tone = intercom enabled. Two tones =
intercom disabled.
Tap the Volume Up Button
Tap the Volume Down Button
Note: In case the person on the other side of the intercom is not responding and
you start talking, 2 beeps will alert you that the other side is not available
STATUS LIGHT
STATUS
None
Headset is off
Alternating Red/blue flashes
Mobile phone/GPS Pairing mode
1 blue flash every 3 seconds
Standby – No call is in progress
2 blue flashes every 3 seconds
Call is in progress
1 red flash every 3 seconds
STATUS LIGHTS
STATUS LIGHT
STATUS
None
Headset is off
One blue flash every 3 seconds
Headset is on
Battery is low
Steady red (Charger is connected)
Headset is being charged
2 red flashes every 3 seconds
Low battery while a call is in progress
Solid red
Charging
Steady red (Charger is not
connected)
Headset in Intercom pairing
mode
9
English
NOTE: If your Bluetooth mobile phone is paired to a Bluetooth GPS
device, not directly to the SCALA RIDER TeamSet, some of the above
Phone functions may not be compatible.
| SCALA RIDER® TeamSet™
Operation is subject to the following two conditions:
SUPPORT
1) this device may not cause interference and
For additional information please visit our website at
www.cardosystems.com
FAQ: www.cardosystems.com/faq
2) this device must accept any interference, including interference that may
cause undesired operation of the device.
or contact us at:
[email protected]
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must
not be co-located or operating in conjunction with any other antenna or
transmitter.
FCC RF Radiation Exposure Statement:
Phone: USA and Canada: + 1-800-488-0363
International: +4989 450 36819
Industry Canada (IC) Statement
NOTICES
15.21
You are cautioned that changes or modifications not expressly approved by
the part responsible for compliance could void the user’s authority to operate
the equipment.
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by
the part responsible for compliance could void the user’s authority to operate
the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the IC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may
cause undesired operation of the device.
15.105(b)
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
10
SCALA RIDER® TeamSet™ |
IC RF Radiation Exposure Statement:
European CE Notice 
The SCALA RIDER TeamSet headset (the “Product”) is in conformity with the
following essential requirements of Council Directive 1999/5/EC (referred to as
R&TTE Directive): Articles 3.1a, 3.1.b and 3.2. The Product is manufactured in
accordance with Annex II of the above directive.
Cardo hereby notifies you that using this Device may also be in contravention
to local, federal, state or national laws or regulations, and that any use of the
Device is entirely at your sole risk and responsibility.
Declaration of Conformity (DOC)
The SCALA RIDER TeamSet headset is compliant with and adopts the
Bluetooth® Specification 2.0 and has successfully passed all interoperability
tests that are specified in the Bluetooth® specification. However,
interoperability between the device and other Bluetooth®-enabled products is
not guaranteed.
1. You, your heirs, legal representatives, successors or assigns, hereby voluntarily and forever release, discharge, indemnify and hold harmless Cardo
from any and all litigation, claims, debts, demands, actions and liability which
may arise, directly or indirectly, from using the Device for any distress, pain,
suffering, discomfort, loss, injury, death, damages to or in respect to any person or property however caused, WHETHER ARISING FROM THE NEGLIGENCE OR OTHERWISE, and which may hereafter accrue to you on some
future date as a result of said use, to the fullest extent permitted by law.
WAIVER AND GENERAL RELEASE
By using the SCALA RIDER TeamSet headset(s) - hereafter referred to in
the singular - you will waive substantial legal rights including the right
to sue. Please read the following carefully before using the device. If
you do not accept all terms of this agreement, you should immediately
return the product for a full refund. By using the headset you agree to be
bound to this agreement and forfeit the right to sue.
2. You fully understand and assume the risks in using the Device, including
risk of negligent acts or omissions by others.
3. You confirm that you are physically capable to use the Device and that you
have no medical conditions or needs that may infringe upon your abilities to
do so in a safe manner. You confirm that you are at least eighteen (18) years
of age and that you have been advised of the risks associated with the use
of the Device. You further confirm that you will not consume any alcohol that
may affect your alertness or any mind-altering substance, and will not carry,
use or consume these substances before or during the use of the Device.
Using a communication device while riding a motorcycle, scooter, moped, ATV,
quad-bike or any other vehicle or equipment, whether on land, water or air
(jointly referred to as “Vehicle”) requires your complete and undivided attention.
Cardo Systems, Inc., including its Officers, Directors, Affiliates, Parent Company,
Representatives, Agents, Contractors, Sponsors, Employees, Suppliers and
Resellers (jointly referred to as the “Company” or “Cardo”) strongly advises
you to take all necessary precautions and remain alert to the traffic, weather
and road conditions if you choose to use the SCALA RIDER TeamSet headset,
including all derivative models irrespective of its commercial name or branding
(the “Device”), and stop your Vehicle on the roadside prior to initiating or
receiving calls. Any publications, advertisements, announcements or similar
notes that refer to using the Device while riding a Vehicle are solely intended
to address its technical capabilities and should not be misconstrued as if
encouraging users to operate the Device while actively involved in traffic.
4. You fully acknowledge our warnings and understand that: (a) risks and dangers exist in using the Device while in traffic, including but not limited to injury or illness, strains, fractures, partial and/or total paralysis, death or other
ailments that could cause serious disability; (b) these risks and dangers may
be caused by the negligence of the manufacturers or its agents or any third
party involved in designing or manufacturing the Device; (c) these risks and
dangers may arise from foreseeable or unforeseeable causes. You hereby
11
English
By way of purchasing this Device and not returning it for a full refund (see
below), you are irrevocably releasing, indemnifying from any liability, loss,
claim and expense (including attorneys fees) and holding Cardo harmless for
any bodily injuries, harm or death as well as losses or damages in goods, to
any Vehicles including your own, or to any property or asset that belong to you
or to third parties, any of which may result from using the Device under any
circumstances or conditions and irrespective of jurisdiction. Cardo will not be
responsible for any physical damages, irrespective of reasons, conditions or
circumstances, including malfunctioning of the Device, and all risks associated
with operating it rest solely and entirely with the user of this Device, irrespective of whether the Device is used by the original purchaser or any third party.
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must not
be co-located or operating in conjunction with any other antenna or transmitter.
| SCALA RIDER® TeamSet™
assume all risks and dangers and all responsibility for any losses and/or
damages, whether caused in whole or in part by the negligence or other
conduct of others, including the Company.
DEVICE, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING
NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. YOU ACKNOWLEDGE AND
AGREE THAT THE LIMITATIONS SET FORTH ABOVE ARE FUNDAMENTAL
ELEMENTS OF THIS AGREEMENT AND THE DEVICE WOULD NOT BE
PROVIDED TO YOU ABSENT SUCH LIMITATIONS. SOME STATE STATUTES
MIGHT APPLY REGARDING LIMITATION OF LIABILITY.
5. You confirm that you have read this release of liability and fully understand
its terms and that you have given up substantial rights by not returning the
Device for a full refund (see refund option below).
Disclaimer of Warranty
CARDO DISCLAIMS ALL EXPRESS AND IMPLIED WARR ANTIES
WITH REGARD TO THE ENCLOSED DEVICE, INCLUDING WITHOUT
LIMITATION ANY IMPLIED WARR ANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT.
THE DEVICE AND ITS ACCESSORIES ARE PROVIDED “AS
IS” AND “AS AVAILABLE” WITHOUT WARR ANTY OF ANY KIND
BEYOND THOSE ASSUMED IN THE ENCLOSED MANUAL.
RETURN FOR FULL REFUND
IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDITIONS, YOU MAY RETURN THIS DEVICE TO CARDO FOR A FULL REFUND,
PROVIDED THAT YOU DO SO NO LATER THAN 7 BUSINESS DAYS FOLLOWING THE PURCHASE OF THE DEVICE (proof of purchase required)
AND SUBJECT TO THE WRAPPING BEING INTACT. WHEN DOING SO,
PLEASE REFER TO THIS SECTION. BY NOT RETURNING THE DEVICE
FOR REFUND WITHIN THE PERIOD PROVIDED, YOU ARE EXPLICITLY IN
AGREEMENT WITH THE ABOVE, AND RENOUNCE ALL RIGHTS TO FUTURE CLAIMS AND DEMANDS AGAINST CARDO AS DEFINED ABOVE.
Limitation of Liability
IN NO EVENT SHALL CARDO BE LIABLE FOR ANY SPECIAL, INDIRECT,
PUNITIVE, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES,
OR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THE
www.cardosystems.com
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement