version 1.1 print date: 4/2013 Digital Tape Meter LS502-E1

version 1.1 print date: 4/2013 Digital Tape Meter LS502-E1
version 1.1
Digital Tape Meter LS502-E1
print date: 4/2013
Install batteries
Device structure
Measure key
Body measurements
Select key
Data store
Power button
User
Coupling
Measurement
Slide off the battery cover
according to the arrow direction.
Tape
Internet disconnection
Battery cover
Low battery indicator
Wireless transmit
Measure value
Install 2 AA batteries according to the
marks in the battery compartment.
Replace the battery cover.
1
2
Before using
Register device
1. Log into your account at www.profileplan.net and
1. Install the data bridge. Please refer to the bridge
instruction manual. (If data bridge is already installed,
skip these steps.)
choose "Account Settings" > "Device Sync."
2. Enter your device’s serial number and click "Sync
2. Sync the device with your working data bridge. More
instructions on syncing your device can be found at
support.profileplan.net.
Device."
3. If successful, the device will display as “ Synced."
3. Ensure that you have an account setup at
profileplan.net. If not, you can register for an account at
www.profileplan.net/signup
4. Finally, manually ”Sync” the device again.
5. See "Activate device" on the following pages if
device does not display as synced.
3
4
Activate device
Register device
1. Bring the device within 3 feet of the data bridge.
2. Press the power button
5
for 5 seconds.
6
3. The screen
will appear. Wait for the screen
Operating instructions
to
1. Power up the unit, press the
select key
to cycle through
the measurement location options
appear. If this screen does not display, see trouble shooting.
2. Gently pull out the tape to start
measuring.
3. Wrap selected body part with tape.
See trouble shooting
4. Insert the plastic end of the tape into the
coupling. Press the measure key
to
measure and store data.
Move to next step
7
8
Cautions
5. The data, including those failed to be
sent before, will be automatically sent to
To prevent the product from harming users and to prolong
product life, please follow guidelines below.
the data bridge. After the data is sent the
unit will turn off automatically. If there is
data failure the icon
will display.
Symbol meaning
6. Log into www.profileplan.net to check
the results or use the mobile app.
General instruction
Forbidden
Disassembly is forbidden
9
10
About battery use
About the device
2 x AAA batteries are required for this product.
Keep measuring at the same time of every day. For
example, before you go to bed.
If the product is not used for extended periods of
time remove batteries.
Measure and check the data corresponding to the part you
choose.
Measure close to the body to avoid interference caused by
clothing.
When you insert the batteries please make
sure they are in the correct position.
Do not disassemble product if you’re not a professional.
Do not heat the batteries or expose them to
flame.
About daily maintenance
Do not combine old and new batteries.
Please store in a cool, dry place.
Do not disassemble battery charger.
Place the product on the horizontal platform when not
in use
Comply to the environmental rules when disposing of
this product.
11
12
Cleaning
1. Use a damp cloth to gently clean the device.
2. Dry the device after cleaning it.
13
14
Trouble shooting
LCD error code
No Display
Symptom
Reason/
Cause
Low charge
Solution
Wrong battery
installation
1. Wireless communication is
interrupted
2. The product is too far away from
the data bridge during activation
Install new batteries
Align polarity symbols (+/-)
Network failure
Re-activate the product within 3 feet of the data bridge
15
16
LCD error code
When using the device, the LCD displays
Symptom
Reason/
Cause
Product is still
not registered.
Solution
Register the
device
(see step 1)
Data bridge limit of 16 devices
has been reached
Go to www.profileplan.net and
delete the unused device or
purchase a new data bridge.
17
Wide Band failure. The data
bridge’s WAN LED light flashes
Low battery
Check the internet connection
Replace the batteries
18
When using the device the LCD displays
When using the device, the LCD displays
Symptom
Reason/
Cause
The wireless
communication between
the product and data
bridge is interrupted
Solution
Re-measure, keeping the data bridge within 3 feet
of the product.
The system can't automatically
identify the measurement data and
exceeds the identification range
The product is out of
wireless transmission
range
Check the network connection
of the data bridge
19
20
Specifications
Symptom
The platform of the Health Center can't indicate
the measurement data normally.
Item
Product name
Reason/
Cause
The measurement data
is near or over the
identification range. The
system can’t identify
Product dimensions
Wide Band failure.
The data bridge’s
WAN LED light
flashes
Weight
Power supply
Display mode
Solution
Go into Device
management > Product
> Data authentication
and assign the data
manually
Unit of measure
Capacity
Check network
connection
Division
21
Parameter
Digital Tape Meter LS502-E1
3 x 2.6 x 1.5 in
85 g (excluding batteries)
2 x AAA
Blue film LCD
Inch
2.2 in min - 59 in max
0.1 in
Working condition
Temperature: 32 ~ 104 ºF
Storage &
transportation condition
Temperature: -4 ~ 140 ºF
22
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement