TRIO MASTER GB.cdr
OTHER SYSTEMS OF THE TRIO FAMILY
TRIO CLUB
TRIO SESSION
Subwoofer 10” - 250 mm - VC 50 mm
Satellites 2 x 6,5” - 165 mm - VC 32 mm
Dome Tweeter - VC 30 mm
Power Max/RMS: 1000 / 500 W
SPL Max: 121 dB
Subwoofer 12” - 320 mm - VC 65 mm
Satellites 2 x 8” - 200 mm - VC 50 mm
Horn Compression Tweeter - VC 34 mm
Power Max/RMS: 1280 / 640 W
SPL Max: 124 dB
Full Range Sound System
PROFESSIONAL SPEAKERS, AMPLIFIERS AND ACCESSORIES
Audiodesign Srl
Via dell’industria, 28 - 42025 CAVRIAGO (RE)
+39 0522 941444 - Fax +39 0522 942363
www.audiodesign-pro.com
[email protected]
TRIO MASTER
User Manual
Portable Full Range Sound System TRIO MASTER
Introduction
Thank you for purchasing an AudioDesign TRIO Active Sound system.
TRIO series is designed to provide an high and powerful sound quality in a compact size.
The main features are:
* Active subwoofer cabinet with additional amplifiers for the passive satellites.
* High sensitivity passive satellites.
* High and precise acoustic quality also with high power.
* Portability: the system is easy fit and portable by one person.
The final result is a full, detailed and powerful sound.
Application
The KPRO
TRIO systems are a professional solution for every DJ or Live events where high pressure and extreme
sound quality is required.
Portable Full Range Sound System TRIO MASTER
TECHNICAL SPECIFICATIONS
INPUT
SUBWOOFER STAGE PRO W15
LINE IN: Combo Socket XLR 3-F / Jack Stereo
INPUT: Balanced and Unbalanced
OUTPUT
SATELLITES OUTPUT: Speakon NL4 (pin 1+ = +, pin 1- = -)
AMPLIFIERS
Subwoofer Power Output:
Satellites Power Outputi:
SPEAKER
WEIGHT & SIZES
Precautions:
Caution: When using any electric product , precautions should always be taken, including the following:
1) Read carefully all instructions before using the product.
2) To reduce the risk, strict supervision is necessary when the product is used near children.
3) Don't use the product near to water sources like sinks, kitchens, wet floors, pools,
or similar or when raining.
4) In case hearing losses or buzzing occur, please contact a doctor.
5) This products should be located so that its position does not interfere or reduce its proper ventilation.
6) This product should be site away from heat sources such as radiators or any other product that
generate heat.
7) This product should be connected to a power supply line only of the type described on the operating
instructions. Check always the status of the power cable.
8) In case you need to replace the fuse, unplug power supply before replacement. The fuse is located
over the power socket and needs to be replaced with a fuse of same type and value. If the fuse blows again,
please contact our service. DON'T replace it a second time with a higher value fuse.
9) Unplug power supply when left unused for a long period of time. Don't draw the cable but pull out the
plug.
10) Make sure that power switch can always be easily reached.
11) The product needs to be inspected by authorized or qualified personnel in case:
A- The power cable or plug are damaged
B- Objects or liquids fall inside the product
C- The product has been exposed to rain
D- The product doesn't appear to operate normally or exhibits a marked change in performance.
E- The product has fallen and been damaged.
12) DON'T operate on the product, except indications on the user's manual . Please refer to authorized
and qualified personnel for any other operation.
13) Caution: Don't place objects on the product's power cable or place it in a position where it could be
damaged or cause interferences. Improper installation could cause fire risk and/or personal injury.
INPUT
SPEAKERS
MAIN FEATURES
WEIGHT & SIZES
380 W RMS
2x170 W RMS
@ 4 Ohm Load
Electronic Crossover LP Subwoofer:
Frequency
46 - 240 Hz / 12 dB/Oct.
Electronic Crossover HP Satellites:
Frequency
38 - 250 Hz / 12 dB/Oct.
Subwoofer:
1 x 15” (380 mm) VC 75 mm
Frequency Response:
20 ÷ 120 Hz
(± 3 dB)
SPL Max:
Max:
127
123 dB
SPL
Weight Subwoofer:
Sizes (WxLxH) cm:
43,5 kg
58,5 x 48,5 x 55
SATELLITE STAGE PRO 10
SATELLITES INPUT: Speakon NL4 (pin 1+ = +, pin 1- = -)
(250 mm)
1 x 10”
High Sensitivity Woofer
VC 44 mm
Compression Horn Tweeter
TOTAL IMPEDANCE :
TOTAL POWER :
TOTAL SPL Max:
Frequency Response:
Tweeter Crossover:
Weight Satellite:
Size (WxLxH) cm:
VC 50 mm
4 Ohm
300 W RMS (600 W Max) with X-over 200 Hz 18 dB/oct
127 dB
70 ÷ 20000 Hz (± 3 dB)
18 dB/oct
Passivo
8000 Hz
13 kg
32 x 30 x 46
BY MEANS OF OUR ACCESSORIES, DIFFERENT CONFIGURATIONS OF THE SYSTEM ARE POSSIBLE
Service
All Audio Design PRO products have been inspected and tested before leaving the factory and , if properly
used, they will work for many years. However, in case of any problem, please proceed in the following way:
Contact your dealer and inform about the defect you found
In case it won't be possible to solve the problem with the dealer, the product needs to be returned, preferably
in its original packaging or in a proper packing to protect it during the transport. Purchase documents must
be produced too.
Your dealer will arrange the shipment to our service centre.
Conformity:
Audiodesign Pro products comply with presently existing directives and standards.
-2-
(760 W Max)
(2x340 W Max)
-7-
Portable Full Range Sound System TRIO MASTER
Portable Full Range Sound System TRIO MASTER
6
Volume setting of the system is made by means of the three LEVEL
knobs on top of the subwoofer:
6
- Left satellite is GAIN LEFT
6
- Right satellite is GAIN RIGHT
- Subwoofer is GAIN SUBWOOFER 3
6
3
SYSTEM COMPONENTS
Thi TRIO MASTER stereo system is composed by three elements:
PEAK
L
HI PASS
GAIN
HIGH
LOW PASS
80
80
120
60
50
Hz
260
+15
0
10
50
Hz
GAIN
GAIN
HIGH
HI PASS
80
PHASE
SHIFT
120
60
-15
PEAK
PEAK
0 - 180°
260
0
0
10
10
-15
+15
R
50
Hz
260
POWER
Subwoofer
LEFT speaker
1 Active Subwoofer STAGE PRO W15
2 Passive Satellites STAGE PRO 10
120
60
R IGHT speaker
Active Subwoofer STAGE PRO W15
Before switching power on and proceed to system setting, make sure that
all three knobs are completely turned counterclockwise, at level 0, and that the mixer output is set so that the peaks level
stays about within 0 e +3 dB.
The active subwoofer STAGE PRO W15 is equipped with a
15" (380 mm) woofer with 75 mm VC.
The cabinet integrates all necessary electronics for amplification and system
processing:
Set first the satellites volume alone and then the subwoofer volume alone.
3 amplifiersi in AB Class for a total power of 720 W RMS (1440 W Max)
Satellites Volume setting
1 x 380 W RMS (760 W Max) for the Subwoofer itself
2 x 170 W RMS (340 W Max) for the two passive satellites (@ 4 Ohm load)
Switch power on and begin to turn clockwise the satellite GAIN knobs 6 until the correspondent PEAK led begins
to flash shortly for less than 1 second.
This is the optimal level being connected to a mixer sending to MAIN a signal with level peaks within 0 and +3dB.
The Subwoofer signal is LowPass filtered, adjustable from 46 to 240 Hz 12 dB/oct.
The Satellites signals are HighPass filtered, adjustable from 38 to 250 Hz 12 dB/oct.
Now listen to the satellites with this output level; if you detect distorsion or saturation of the signal (i.e of microphone) check
the possibility of reducing the level of the signal concerned at his source, otherwise try to slightly lower the mixer’s main
otput. Should this not be enough, reduce the satellites volume until you have an optimal sound.
Memorize the knobs setting.
Cabinet of high density MDF, anti-scratch embossed painting
Practical transport handles hollowed into the wood
Integral rigid metal grill
Sub Volume setting
After having memorized the knobs setting LEFT e RIGHT, take them back to 0 and begin now to turn clockwise the
SUBWOOFER GAIN knob 3 until the correspondent PEAK led begins to flash shortly for less than 1 second.
This is the optimal level being connected to a mixer sending to MAIN a signal with level peaks within 0 and +3dB.
Housing hole for ø 35 mm stand tubes
Sizes & weight: 58 x 48 x 55 cm; 43.5 kg.
Now listen to the Sub with this output level; if you detect distorsion of basses, turn slightly the knob back counterclokwise.
Connections and Control Panels
Final system setting
Bring the three knobs at the optimal level you have checked and listen to the complete system, again at the mixer
main level peaks between 0 and +3 dB.
If you detect to much basses compared with satellites output, turn slightly back the SUB LEVEL knob.
If you detect instead not enough basses, turn slightly back the setellites LEVEL LEFT and RIGHT knobs.
PEAK
L
HI PASS
GAIN
HIGH
80
120
50
Hz
260
+15
0
10
50
Hz
HIGH
R
HI PASS
80
0 - 180°
260
0
10
10
-15
+15
Subwoofer
50
Hz
260
4 Phase Switch 0-180°
R IGHT speaker
4
9
5 Satellites Clip Indicator (Separated Left and Right)
6 Satellites Volume control separated on channel LEFT and RIGHT.
it controls only the signal going respectively to left and right satellite.
13
RESPONSE DIAGRAM TRIO MASTER
- dB SPL/watt (4 ohm load)
3 Subwoofer Volume control
120
60
0
POWER
LEFT speaker
As a general rule , the output level of the mixers should be set so that the sound peaks remain between 0 to +3 dB
about. When the system TRIO MASTER gets in the two Line In (10 and 11) a signal with that amplitude and it is
set as explained above, it grants the maximum performance in terms of maximum undistorted amplification (at clip
limit) and in this conditions you get the maximum possible sound pressure (SPL).
Sensitivity Magnitude
GAIN
PHASE
SHIFT
120
60
-15
PEAK
GAIN
1 Subwoofer Clip Indicator
2 Subwoofer LOW PASS control adjustable from 46 to 240 Hz
5 6 7 8
PEAK
LOW PASS
80
60
-6-
2 1 3
8 7 6 5
12
18
7 High tones equalization separated for left and right channel -15 / +15 dB
11 10
8 Satellites HI PASS control separated LEFT and RIGHT from 38 to 250 Hz
ATTENTION: the HI PASS frequency should not be set under 120 Hz
@ 1W/1m
LINE IN
OUTPUT
OUT+:1+/ OUT- :1-
M
L
S
S
A
95.0
90.0
RIGHT
LEFT
RIGHT
GND=1=SLEEVE HOT=2=TIP COLD=3=RING
10 Right Channel Line In
Combo Socket XLR 3-F / Jack 6,3 mm Balanced
11 Left Channel Lin In
Combo Socket XLR 3-F / Jack 6,3 mm Balanced
USE ONLY WITH 250V FUSE
220
85.0
9 ON LED indicator (Red)
ST
MONO
LEFT
SPEAKER OUTPUT: [email protected]Ù
80.0
12 Speakon Socket Right Satellite
75.0
13 Speakon Socket Left Satellite
70.0
14
65.0
60.0
Amplifier cooling fan; keep it clean for a correct ventilation.
15 On/Off power switch - In positioe 0 the system is Off
55.0
16 Voltage Selector
50.0
14
45.0
15
16
17
17 Power Net Socket
18 ST/MONO Switch (Stereo / Mono): se si seleziona STEREO,
aut o
20.0
100.0
AUDIODESIGN PRO: TRIO MASTER
1000.0
log Frequency - Hz
10000.0
MLSSA: Frequency Domain
When STEREO is selected, the system sends to the Right and Left channels the
correspondent Right and Left input signals.
When MONO is selected, the system sends to both Right and Left channels only
the LEFT input signal, so one complete system per channel can be used..
-3-
Portable Full Range Sound System TRIO MASTER
Portable Full Range Sound System TRIO MASTER
High sensitivity passive satellites STAGE PRO 10
CONNECTION OF TWO SYSTEMS IN MONO CONFIGURATION
The high sensitivity passive satellite STAGE PRO 10 is a bass reflex
cabinet equipped with:
(ST/MONO Switch down)
RIGHT CHANNEL
LEFT CHANNEL
One 10" (250 mm) woofer with a 50 mm vented voice coil
LEFT/ MONO
RIGHT
1
MIC 2
MIC 3
MIC 4
MIC 5
INPUT
OUTPUT
CD/TAPE
1
2
MIC 1
PAM
2
FX
X 2 .6 2
ULTRALOW-NOISE DESIGN
14-INPUT 2/2-BUS MIC/LINE MIXER
WITH PREMIUM MIC PREAMPLIFIERS AND
DIGITAL 24-BIT MULTI-EFFECTS PROCESSOR
USB AUDIO INTERFACE
MIC 6
AUX SENDS
24-BIT MULTI-FX PROCESSOR
One compression horn tweeter with a 44 mm voice coil
80 CHORUS & REVERB
82 FLANGER & REVERB
84 PHASER & REVERB
86 PITCH & REVERB
88 DELAY & REVERB
90 DELAY & GATED
91 DELAY & REVERSE
92 DELAY & CHORUS
94 DELAY & FLANGER
96 DELAY & PHASER
98 DELAY & PITCH
36 REVERSE
40 EARLY REFL
44 AMBIENCE
48 STADIUM
49 AMBIENCE FX
50 DELAY
59 ECHO
60 CHORUS
66 FLANGER
70 PHASER
74 PITCH SHIFT
00 SMALL HALL
03 MID HALL
06 BIG HALL
09 CHURCH
10 SMALL ROOM
13 MID ROOM
16 BIG ROOM
19 CHAPEL
20 SPRING
27 SPRING
30 GATED REV
USB
INTERFA
LINE IN 5/6
High Pass Filter at 8000 Hz 18 dB/oct on tweeter
LAM
LINE IN 7/8
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
MID
MID
2.5 kHz
MID
2.5 kHz
MID
2.5 kHz
MID
2.5 kHz
MID
2.5 kHz
MID
2.5 kHz
P
12V
400
PROGRAM
( PUSH )
MID
2.5 kHz
2.5 kHz
AUX SENDS
1
LOW
LOW
80 Hz
LOW
80 Hz
LOW
80 Hz
LOW
80 Hz
LOW
80 Hz
LOW
80 Hz
CE
mA
STEREO AUX RETURNS
1
1
TO AUX
LOW
80 Hz
80 Hz
SEND 1
SOLO
1
4 ohm Impedance
AUX
1
AUX
1
AUX
1
AUX
1
AUX
1
AUX
1
AUX
1
AUX
2
2
FX
FX
MAIN MIX
ALT 3-4
SOLO
2
PRE
2
PRE
2
PRE
2
PRE
2
PRE
2
PRE
2
PRE
2
PRE
2-TR/USB TO MAIN
2-TR/USB
FX
FX
FX
FX
FX
FX
FX
FX
PAN
PAN
PAN
PAN
PAN
PAN
BAL
BAL
10
5
ALT 3-4
2
MAX
PHONES/CTRL R
Speakon socket for connection to the subwoofer amplifier
0
2
MAIN MIX
MAIN SOLO
PFL
5
SOURCE
1
2
3
5
6
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
ALT 3-4
ALT 3-4
ALT 3-4
ALT 3-4
ALT 3-4
ALT 3-4
ALT 3-4
ALT 3-4
dB
MUTE
dB
MUTE
4
dB
MUTE
dB
MUTE
dB
MUTE
7/8
dB
MUTE
dB
9/10
MUTE
dB
20
3
4
MUTE
CLIP
CLIP
CLIP
CLIP
CLIP
CLIP
CLIP
CLIP
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
MODE
SOLO (NORMAL)
PFL (LEVEL SET)
L
R
Cabinet in high density MDF , embossed anti-scratch painting
Integral protection grill
1
2
3
4
5
6
7/8
9/10
AL T 3-4
MAIN MIX
Housing hole for ø 35 mm stand tubes
Sizes and Weight: 32 x 30 x 46 cm; 13 kg.
LINE IN
OUTPUT
OUT+:1+/ OUT- :1-
LINE IN
OUTPUT
OUT+:1+/ OUT- :1-
ST
MONO
ST
MONO
LEFT
LEFT(Mono)
RIGHT
SPEAKER OUTPUT:
LEFT
LEFT(Mono)
RIGHT
SPEAKER OUTPUT:
RIGHT
GND=1=SLEEVE HOT=2=TIP COLD=3=RING
RIGHT
GND=1=SLEEVE HOT=2=TIP COLD=3=RING
220
LEFT/ MONO
RIGHT
1
MIC 2
MIC 3
MIC 4
MIC 5
INPUT
OUTPUT
CD/TAPE
1
2
MIC 1
PAM
2
FX
USE ONLY WITH 250V FUSE
SYSTEM CONNECTION IN STEREO CONFIGURATION
(ST/MONO Swich up)
USE ONLY WITH 250V FUSE
220
NET
X 2 .6 2
ULTRALOW-NOISE DESIGN
14-INPUT 2/2-BUS MIC/LINE MIXER
WITH PREMIUM MIC PREAMPLIFIERS AND
DIGITAL 24-BIT MULTI-EFFECTS PROCESSOR
USB AUDIO INTERFACE
MIC 6
AUX SENDS
24-BIT MULTI-FX PROCESSOR
80 CHORUS & REVERB
82 FLANGER & REVERB
84 PHASER & REVERB
86 PITCH & REVERB
88 DELAY & REVERB
90 DELAY & GATED
91 DELAY & REVERSE
92 DELAY & CHORUS
94 DELAY & FLANGER
96 DELAY & PHASER
98 DELAY & PITCH
36 REVERSE
40 EARLY REFL
44 AMBIENCE
48 STADIUM
49 AMBIENCE FX
50 DELAY
59 ECHO
60 CHORUS
66 FLANGER
70 PHASER
74 PITCH SHIFT
00 SMALL HALL
03 MID HALL
06 BIG HALL
09 CHURCH
10 SMALL ROOM
13 MID ROOM
16 BIG ROOM
19 CHAPEL
20 SPRING
27 SPRING
30 GATED REV
USB
INTERFA
LINE IN 5/6
LEFT CHANNEL
LAM
LINE IN 7/8
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
P
12V
400
RIGHT CHANNEL
PROGRAM
( PUSH )
MID
MID
MID
MID
MID
MID
MID
MID
2.5 kHz
2.5 kHz
2.5 kHz
2.5 kHz
2.5 kHz
2.5 kHz
2.5 kHz
2.5 kHz
AUX SENDS
STEREO AUX RETURNS
1
LOW
LOW
80 Hz
LOW
80 Hz
LOW
80 Hz
LOW
80 Hz
LOW
80 Hz
LOW
80 Hz
1
1
TO AUX
LOW
80 Hz
CE
mA
80 Hz
SEND 1
SOLO
1
AUX
1
AUX
1
AUX
1
AUX
1
AUX
1
AUX
1
AUX
1
AUX
2
PRE
2
PRE
2
PRE
2
PRE
2
PRE
2
PRE
2
PRE
2
PRE
2
2
FX
FX
MAIN MIX
ALT 3-4
SOLO
2-TR/USB TO MAIN
2-TR/USB
FX
FX
FX
FX
FX
FX
FX
FX
PAN
PAN
PAN
PAN
PAN
PAN
BAL
BAL
10
Depending on the choosen configuration, connect the system following the precedent wiring schemes.
5
ALT 3-4
2
MAX
PHONES/CTRL R
0
2
MAIN MIX
MAIN SOLO
PFL
5
SOURCE
1
2
MUTE
3
MUTE
ALT 3-4
MUTE
MUTE
MUTE
6
MUTE
ALT 3-4
dB
MUTE
7/8
MUTE
ALT 3-4
dB
MUTE
9/10
MUTE
ALT 3-4
dB
MUTE
dB
20
MUTE
ALT 3-4
dB
ALT 3-4
MUTE
3
dB
CLIP
CLIP
CLIP
CLIP
CLIP
CLIP
CLIP
CLIP
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
2
3
4
5
7/8
6
4
MUTE
9/10
MODE
SOLO (NORMAL)
PFL (LEVEL SET)
L
R
Connection to the electric net
AL T 3-4
Check that Power switch 15 is in position 0 and that net voltage corresponds to the one selected in the system.
Connect the supplied electric wire to an electric net socket equipped with a correct ground contact.
MAIN MIX
.
.
Satellite connection
Use wires with good quality Speakon plugs. Make sure to rotate the Speakon plugs clockwise up to the lock position.
Connection to the mixer
Before making any connection to the mixer make sure the system power switch is Off in order to avoid damages.
Remember that electric net power il the last to be switced On and the first to be disconnected after use!
LINE IN
OUTPUT
OUT+:1+/ OUT- :1-
ST
MONO
LEFT
LEFT(Mono)
RIGHT
SPEAKER OUTPUT:
RIGHT
GND=1=SLEEVE HOT=2=TIP COLD=3=RING
System Volume setting
USE ONLY WITH 250V FUSE
220
1
MUTE
ALT 3-4
dB
5
4
MUTE
ALT 3-4
dB
NET
The TRIO MASTER system is provided vith clip limiters and peack level indicators separate and independent on all three
channels, and doesn’t require therefore any special setting procedure.
Thus the system is able to deliver excellent performances, and should be used with input signals at optimal level, starting from
kind and quality of the used cables, and the prevention of any kind of distortion.
In fact the presence of distortion doesn’t only deliver a poor performance of the system, but it is also a real risk on long periods,
to damage the system itself.
We kindly invite you therefore,to strictly follow the following instructions on how to set the level of alla comonents.
-4-
-5-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement