MK71050-03 Evaluation Kit Hardware Manual

MK71050-03 Evaluation Kit Hardware Manual
FEXK71050-03_USB-EK_HardManual-01
MK71050-03 Evaluation Kit
(MK71050-03USB-EK)
Hardware Manual
Initial Release (Official): June 11, 2015
MK71050-03USB-EK Hardware Manual
Precautions for the Specification
1) Contents of the Specification are the information at the time of their issuance. The information contained herein is subject
to change without notice.
2) LAPIS Semiconductor has used reasonable care in preparing the information included in the Specification, but LAPIS
Semiconductor does not warrant that such information is error free. LAPIS Semiconductor assumes no liability whatsoever
for any damages incurred by you resulting from errors in or omissions from the information included herein.
3) The technical information specified herein is intended only to show the typical functions of the Products and examples of
application circuits for the Products. No license, expressly or implied, is granted hereby under any intellectual property
rights or other rights of LAPIS Semiconductor or any third party with respect to the information contained in this
document; therefore LAPIS Semiconductor shall have no responsibility whatsoever for any dispute, concerning such rights
owned by third parties, arising out of the use of such technical information.
4) The Specification contains information related to the LAPIS Semiconductor’s copyright and technical know-how. Any use
of them other than pertaining to the usage of appropriate products is not permitted. Further, the Specification, in part or in
whole, may not be reprinted or reproduced and disclosed to third parties without prior consent of LAPIS Semiconductor.
Precautions for the Products
●Precautions for Safety
1) The Products are designed and produced for application in ordinary electronic equipment (AV equipment, OA equipment,
telecommunication equipment, home appliances, amusement equipment, etc.).
2) For use of our Products in applications requiring a high degree of reliability (as exemplified below), please contact and
consult with a LAPIS Semiconductor representative: transportation equipment (i.e. cars, ships, trains), primary
communication equipment, traffic lights, fire/crime prevention, safety equipment, medical systems, servers, solar cells,
and power transmission systems.
3) Do not use our Products in applications requiring extremely high reliability, such as aerospace equipment, nuclear power
control systems, and submarine repeaters.
4) The Products are designed for use in a standard environment and not in any special environments.
Application of the Products in a special environment can deteriorate product performance. Accordingly, verification and
confirmation of product performance, prior to use, is recommended if used under the following conditions:
[a] Use in various types of liquid, including water, oils, chemicals, and organic solvents
[b] Use outdoors where the Products are exposed to direct sunlight, or in dusty places
[c] Use in places where the Products are exposed to sea winds or corrosive gases, including
Cl2, H2S, NH3, SO2, and NO2
[d] Use in places where the rPoducts are exposed to static electricity or electromagnetic waves
[e] Use in environment subject to strong vibration and impact.
[f] Use in proximity to heat-producing components, plastic cords, or other flammable items
[g] Use involving sealing or coating the Products with resin or other coating materials
[h] Use of the Products in places subject to dew condensation
5) The Products might receive the radio wave interference from electronic devices such as Wireless LAN devices, Bluetooth
devices, digital cordless telephone, microwave oven and so on that radiate electromagnetic wave.
6) The Products are not radiation resistant.
7) Verification and confirmation of performance characteristics of Products, after on-board mounting, is advised.
8) Confirm that operation temperature is within the specified range described in the Specification.
PEXK71050-03_USB-EK_HardManual-01
i
MK71050-03USB-EK Hardware Manual
9) Although LAPIS Semiconductor is continuously working to improve product reliability and quality, semiconductors can
break down and malfunction due to various factors. Therefore, if product malfunctions may result in serious damage,
including that to human life, sufficient fail-safe measures must be taken, including the following:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits in the case of single-circuit failure
10) Failure induced under deviant condition from what defined in the Specification can not be guaranteed.
11) This product is a specification to radiate the radio wave. It is necessary to acquire the attestation of decided Radio Law of
each region used to use the equipment that radiates the radio wave.
Please inquire about the attestation of Radio Law that this product acquires.
12) When product safety related problems arises, please immediately inform to LAPIS Semiconductor, and consider technical
counter measure.
●Precautions for Reference Circuits
1) If change is made to the constant of an external circuit, allow a sufficient margin due to variations of the characteristics
of the Products and external components, including transient characteristics, as well as static characteristics.
2) The reference circuit examples, their constants, and other types of information contained herein are applicable only when
the Products are used in accordance with standard methods. Therefore, if mass production is intended, sufficient
consideration to external conditions must be made.
● Precaution for Electrostatic
This product is Electrostatic sensitive product, which may be damaged due to Electrostatic discharge. Please take proper
caution during manufacturing and storing so that voltage exceeding Product maximum rating won't be applied to the Products.
Please take special care under dry condition (Grounding of human body / equipment / solder iron, isolation from charged
objects, setting of Ionizer, friction prevention and temperature / humidity control etc.)
● Precautions for Storage / Transportation
1) Product performance and connector mating may deteriorate if the Products are stored in the following places:
[a] Where the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2 and NO2
[b] Where the temperature or humidity exceeds those recommended by LAPIS Semiconductor
Temperature: 5°C to 40°C, Humidity 40% to 60%
[c] Storage in direct sunshine or condensation.
[d] Storage in high Electrostatic.
2) Even under LAPIS Semiconductor recommended storage condition, connector mating, mountability, and heat
resistance of products over 1 year old may be degraded.
3) Store / transport cartons in the correct direction, which is indicated on a carton as a symbol, otherwise bent leads may
occur due to excessive stress applied when dropping of a carton.
● Precaution for Product Label
QR code printed on LAPIS Semiconductor product label is only for internal use, and please do not use at customer site.
It might contain internal products information that is inconsistent with product information.
● Precaution for Disposition
When disposing Products, please dispose them properly with a industry waste company.
● Prohibition Regarding Intellectual Property
LAPIS Semiconductor prohibits the purchaser of the Products to exercise or use the intellectual property rights, industrial
property rights, or any other rights that either belong to or are controlled by LAPIS Semiconductor, other than the right to use,
sell, or dispose of the Products.
PEXK71050-03_USB-EK_HardManual-01
ii
MK71050-03USB-EK Hardware Manual
● The other precautions
1) Please use the Products in accordance with any applicable environmental laws and regulations, such as the RoHS
Directive. For more details, including RoHS compatibility, please contact a ROHM sales office. LAPIS Semiconductor
shall have no responsibility for any damages or losses resulting non-compliance with any applicable laws or regulations.
2) When providing our Products and technologies contained in the Specification to other countries, you must abide by the
procedures and provisions stipulated in all applicable export laws and regulations, including without limitation the US
Export Administration Regulations and the Foreign Exchange and Foreign Trade Act.
Copyright
2015 LAPIS Semiconductor Co., Ltd.
2-4-8 Shinyokohama, Kouhoku-ku,
Yokohama 222-8575, Japan
http://www.lapis-semi.com/en/
PEXK71050-03_USB-EK_HardManual-01
iii
MK71050-03USB-EK Hardware Manual
Preface
This document outlines the hardware of MK71050-03 evaluation kit (MK71050-03USB-EK) which
enables 2.4 GHz-band radio communication conforming to Bluetooth® LE on Windows PC via USB.
The following related documents are available for reference.
MK71050-03 Data Sheet
ML7105 Data Sheet
ML7105 User's Manual
Bluetooth Application Controller Interface (BACI) Command Manual
BLE Evaluation Kit AT Command (VSSPP2 Edition) Reference Manual
BLE TOOL User's Manual
BLE Evaluation Kit Setting Utility (VSSPP2 AT Command Edition) Operation Manual
•Bluetooth® is a registered trademark of Bluetooth SIG, Inc.
•All other company and product names are the trademarks or registered trademarks of the respective companies.
PEXK71050-03_USB-EK_HardManual-01
iv
MK71050-03USB-EK Hardware Manual
Table of Contents
Preface ........................................................................................................................................................................... iv
Table of Contents ............................................................................................................................................................ v
1. MK71050-03USB-EK Overview................................................................................................................................1
2. Configuration ............................................................................................................................................................2
2.1 System Configuration .........................................................................................................................................2
2.2 Configuration of MK71050-03 USB Dongle .......................................................................................................3
3. User Interface ...........................................................................................................................................................4
3.1 Connection of uEASE ........................................................................................................................................4
4. Circuit Diagram .........................................................................................................................................................5
4.1 MK71050-03 Evaluation Module ........................................................................................................................5
4.2 USB Conversion Board ......................................................................................................................................7
Revision History ..............................................................................................................................................................8
PEXK71050-03_USB-EK_HardManual-01
v
MK71050-03USB-EK Hardware Manual
1. MK71050-03USB-EK Overview
1. MK71050-03USB-EK Overview
When you receive MK71050-03USB-EK, make sure that all of the following components are included in the kit.
Should there be any missing or broken part, contact our sales representative.
Contents
Components
MK71050-03 USB dongle
- MK71050-03 evaluation module + USB conversion board
uEASE pitch conversion board
MK71050-03USB-EK
configuration
Quantity
1
1
MK71050-03 USB dongle
MK71050-03 evaluation
module
USB conversion board
uEASE pitch conversion board
Figure 1-1
PEXK71050-03_USB-EK_HardManual-01
MK71050-03USB-EK
1
MK71050-03USB-EK Hardware Manual
2. Configuration
2. Configuration
2.1 System Configuration
MK71050-03 USB dongle can operate as Central (Master) or Peripheral (Salve) for the Bluetooth LE connection.
With the LAPIS VSSPP(*) software, it supports the following functions in addition to a simple communication between
PCs.
Master/slave switching
Up to five pairings
Communication with smartphones with Android 4.3 or later
Connection to iPhone beacon application with iBeacon operation
The online shopping-only new GUI (PC) can easily change various parameters of BLE.
(*)VSSPP: Vender Specific Serial Port Profile
See the following related manuals for details.
BLE Evaluation Kit AT Command (VSSPP2 Edition) Reference Manual
BLE TOOL User's Manual
BLE Evaluation Kit Setting Utility (VSSPP2 AT Command Edition) Operation Manual
Figure 2-1
Example 1 of System Configuration with MK71050-03USB-EK
Figure 2-2
Example 2 of System Configuration with MK71050-03USB-EK
(Note) The configuration example 2 requires two kits of MK71050-03USB-EK.
PEXK71050-03_USB-EK_HardManual-01
2
MK71050-03USB-EK Hardware Manual
2. Configuration
2.2 Configuration of MK71050-03 USB Dongle
Figure 2-2 shows the appearance of MK71050-03 USB dongle, and Table 2-1 shows its configuration.
Bottom
Top
(1)
(3)
(4)
(5)
(2)
(6)
(7)
(8)
(9)
Figure 2-2
Table 2-1
No.
Name
MK71050-03 evaluation module
(1)
MK71050-03
(2)
B3U-3000P(M)
(3)
ML610Q482
(4)
Half pitch pin header
(5)
55650-0388
USB conversion board
(6)
54363-0389
(7)
B3U-3000P(M)-B
(8)
FT232RQ
(9)
USB connector
PEXK71050-03_USB-EK_HardManual-01
Appearance of MK71050-03 USB Dongle
Configuration of MK71050-03 USB Dongle
Symbol
Description
U1
S1
U2
J2
J1
Bluetooth LE radio communication module
MK71050-03 reset switch
U8 microcontroller
Connector port for uEASE pitch conversion board
0.5 mm pitch BtoB connector (plug) by Molex
J52
S51
U51
J51
0.5 mm pitch BtoB connector (receptacle) by Molex
Reset switch
USB-UART (USB serial conversion) IC by FTDI
PCB pattern for USB connector A
3
MK71050-03USB-EK Hardware Manual
3. User Interface
3. User Interface
3.1 Connection of uEASE
uEASE is an incircuit emulator (ICE) module for the U8 microcontroller ML610Q482 implemented on the MK71050-03
evaluation module. Connect the MK71050-03 evaluation module with uEASE as shown in the following figure. Because
the pin pitch of the uEASE connector is different from that of the uEASE cable, the uEASE pitch conversion board is
necessary.
Position of pin 1
Connector
Position of pin 1
Figure 3-1
direction mark
Connection of MK71050-03 Evaluation Module and uEASE
The uEASE module enables the following functions.
Writing an application code to the flash memory included in ML610Q482 (*)
On-chip debug function (reset, step run, break point, etc.)
(*) A sample application for VSP software is written at shipment.
For details of the debug function, see the manuals of uEASE.
PEXK71050-03_USB-EK_HardManual-01
4
MK71050-03USB-EK Hardware Manual
4. Circuit Diagram
4. Circuit Diagram
4.1 MK71050-03 Evaluation Module
See the next page.
FEXK71050-03_USB-EK_HardManual-01
5
MK71050-03USB-EK Hardware Manual
4. Circuit Diagram
Figure 4-1
FEXK71050-03_USB-EK_HardManual-01
MK71050-03 Evaluation Module
6
MK71050-03USB-EK Hardware Manual
4. Circuit Diagram
4.2 USB Conversion Board
Figure 4-2
FEXK71050-03_USB-EK_HardManual-01
USB Conversion Board
7
MK71050-03USB-EK Hardware Manual
Revision History
Revision History
Page
Document No.
FEXK71050-03_USB-E
K_HardManual-01
Issue date
Before
revision
After
revision
June 11, 2015
-
-
Revision description
Initial release (official)
(Note) Corrections of errors and change/correction of expressions are not included.
FEXK71050-03_USB-EK_HardManual-01
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement