CD Radio Cassette-Carder
3-856-825-12(1} |
SONY.
CD Radio
Cassette-Corder
Operating Instructions
CFD-646/656
©1996 by Sony Corporation
Warning
To prevent fire or shock hazard, do
not expose the player to rain or
moisture.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING ТО QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert
the user to the presence of
uninsulated “dangerous voltage”
within the product's enclosure
that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert
the user to the presence of
important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
CAUTION
The use of optical instruments with this
product will increase eye hazard.
For customers in Canada
To prevent electric shock, match wide blade
of plug to wide slot, fully insert.
CAUTION
You can use this player on AC power source
only. You cannot use it on batteries.
When you disconnect the AC power cord, the
memory data for the preset memory for radio
will be erased after about 60 minutes.
Re-enter them when you use the player again.
introduction
Information
For customers in the United States
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following measures:
—Reorient or relocate the receiving antenna.
— Increase the separation between the
equipment and receiver.
—Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced
radio/TV technician for help.
You are cautioned that any changes or
medifications not expressly approved in this
manual could void your authority to operate
this equipment.
Owner's Record
The model and serial numbers are located at
the rear of the CD radio cassette-corder.
Record these numbers in the spaces provided
below. Refer to these numbers whenever you
call upon your Sony dealer regarding this
product.
Model No.
Serial No.
About This Manual
The instructions in this manual are for
the CFD-646 and CFD-656. Before you
start reading, check your model number.
The CFD-646 is the model used for
illustration purposes.
Table of contents
Basic Operations
Playing a CD
6 Listening to the radio
Playing a tape
10 Recording on a tape
The CD Player Setting Up
12 Using the display 21 Hooking up the system .
13 Locating a specific track 24 Adjusting the audio emphasis
14 Playing tracks repeatedly (Sound Mode/MEGA BASS)
(Repeat Play)
16 Playing tracks in random order Additional Information
(Shuffle Play) 25 Precautions
17 Creating your own program 27 Troubleshooting
(Program Play) 29 Maintenance
30 Specifications
The Radio 31 Index
19 Presetting radio stations
20 Playing preset radio stations
introduction
suonesadgo >iseg |
3
AN
Playing a CD
For hookup instructions, see pages 21 — 23.
1 OPEN/CLOSE
Press OPEN/CLOSE (direct
power-on) and place the CD on
the CD tray. Be sure to align the
center of the CD with the center
of the CD tray.
Notes C £ —
, . Co VJ] TJ
* You can't play 3-inch (8 cm) } I {
CDs even with an adaptor for /
single-CDs. With the label side up
* Place one CD each only on the
CD tray. If you place one CD
over another and close the CD
tray, you will not be able to pull
out the tray.
2 DISC CHANGE
Press DISC CHANGE to turn the
CD tray, and place second and
third CD on the CD tray.
3 OPEN/CLOSE
4
Basic Operations
Press OPEN // CLOSE to close the
CD tray.
Press Pl.
The player plays all the tracks of
all the CDs in the CD tray once.
Display
CD Track
Playing
number number time
Tips
* You can change a CD
while playing another.
Press OPEN/CLOSE to
pull out the CD tray
and change the CD.
Press OPEN/CLOSE
again to close the CD
tray. Do not close the
CD tray by hand, as
that may cause trouble.
Next time you want to
listen to a CD, just
press Pl. The player
turns on automatically
and starts playing the
CD.
Use these buttons for additional operations
POWER DISC
1-3
OPEN/CLOSE
VOLUME +/-
AMS/SEARCH
</>
a
>i
To Press
Adjust the volume VOLUME +/-
Stop playback a
Pause playback >i
= -
Press again to resume play
after pause.
Go to the next track
AMS/SEARCH Pi
Go back to the previous track
AMS/SEARCH H+<
Remove the CD OPEN/CLOSE
Turn on/off the player POWER
Play only one CD DISC 1, DISC 2 or DISC 3
(desired DISC SELECT)
Basic Operations
5
suonesado >iseg |
y = « ow par
“ arab 5
Listening to the radio
1 2
For hookup instructions, see pages 21 — 23.
Press BAND until the band you Display
want appears in the display с
(direct power-on). SD Ss
=a
hr Sad
Hold down TUNING +/- until Indicates an FM stereo
the frequency digits begin to broadcast.
change in the display. |
The player automatically scans
the radio frequencies and stops
when it finds a clear station.
If you can't tune in a station,
press the button once at a time.
6 | Basic Operations
Tips
* If the FM broadcast is
noisy, press PLAY
MODE/MONO/ST
until “Mono” appears
in the display and the
radio will play in
monaural.
* Next time you want to
listen to the radio, just
press RADIO or BAND.
The player turns on
automatically and
starts playing the
previous station.
Use these buttons for additional operations
POWER PLAY MODE/ VOLUME +/-
MONO/ST
suonesado seg |
То Press
Adjust the volume VOLUME +/-
Turn on/off the radio POWER
To improve broadcast reception
Reorient the aerial for FM.
Reorient the AM loop aerial (supplied). Locate it
away from the player during AM program reception.
"aná ha
<
4”
for FM for AM
Basic Operations | 7
A ABRA
Playing a tape
2 1 21
For hookup instructions, see pages 21 — 23.
Press MA to open the tape
compartment and insert a
recorded tape. Close the
compartment.
With the side you want
to play facing forward
2 Press ==. Display
The player turns on (direct
power-on) and starts playing. COO Sm
8 | Basic Operations
Use these buttons for additional operations
suonesado 21528 |
POWER VOLUME +/--
<</>>
Ha
Il
<</>>
Ha
i
Note To Press
During playback, do
not press buttons on Adjust the volume VOLUME +/-
the other deck. a
Otherwise the playback Stop playback us
speed may change. Fast-forward or rewind the tape Bor «<<
Tips Pause playback il
Press the button again to
* Next time you want to
у resume play after pause.
listen to a tape, just
press >. The player Eject the cassette HL
turns on automatically
and starts playing the Turn on/off the player POWER
tape.
e For the best results, use
TYPE I (normal) tape.
Basic Operations | 9
dA A МР;
Recording on a tape
2 2 3 1
For hookup instructions, see pages 21 — 23.
Press l£ to open the tape
compartment on deck B and
insert a blank tape.
With the side you want to
record on facing forward
[=
B
2 Select the program source you
want to record.
To record from the CD player,
insert a CD (see page 4) and press
H on the CD section.
To record from the radio, press
BAND and tune in the station
you want (see page 6.)
Deck A To record from a tape,
insert a recorded tape into
deck A and press Il and
> simultaneously on
deck A.
Basic Operations
Display
С 1 > ALL DISCS EXT
23 sm
{оо с.
442 1
Co “Se
OO a Sa
cu 0700
Fe CAL
FE
COC Sm
To
PAPE
Start recording.
To record, press @ on deck B (I
is depressed automatically).
Tips
* Adjusting the volume
or the audio emphasis
(see page 24) will not
affect the recording
level.
* For the best results, use
TYPE I (normal) tape
for recording.
* When rétording from
two or three CDs, the
player pauses
recording and makes a
blank between the
tracks while CDs are
being changed, When
changing of CDs is
finished, recording
resumes automatically.
* To erase a recording,
proceed as follows:
1 Insert the tape whose
recording you want
to erase into the tape
compartment on deck
B.
2 Press TAPE until
“TAPE” appears in
the display window.
3 Press @ on deck B.
Notes
* Do not press ог
«dl while recording on
a tape.
* If the AM program
makes a whistling
sound after you've
pressed @ in step 3,
move the AM loop
aerial connected to the
player as far as
possible.
Use these buttons for additional operations
POWER
С
suonesado 21588 |
То Press
Stop recording Ш ^ on deck B
Pause recording ID on deck B
Press the button again to
resume recording.
Turn on/off the player
POWER
Basic Operations
"a"
Smo rege,
The CD Player
Using the display
You can check information about the CD
using the display.
Tip
When two or three CDs
are placed, select the
CD you want to check
information about by
pressing DISC 1, DISC
2 or DISC 3.
12 | The CD Player
DISPLAY
Checking the total track numbers and playing
time of the current CD
Press DISPLAY in stop mode.
DO A
Current CD number
Total track numbers
Total playing
time
Checking the remaining time of the current
CD
Press DISPLAY while playing a CD.
To display Press DISPLAY
The current track number Once
and the remaining time
on the current track*
Remaining time on the CD Twice
and the number of tracks left
The current track number Three times
and playing time
* For a track whose number is more than 16, the remaining
time appears as “———-".
Locating a specific
track
You can quickly locate any track using
the number buttons. You can also find a
specific point in a track while playing a
CD.
Note
You cannot locate a
specific track if
“SHUF” or "PGM" is lit
in the display. Turn off
the indication by
pressing M.
Tip
When you locate a
track numbered over
10, press >10 first, then
the corresponding
number buttons.
Example:
To play track number
23, press >10 first, then
2 and 3. |
—
FUNCTION MODE [POWER
DO ó
DISC1 DISC? DISC3
—
DISC 1-3
Number
buttons
19Áe|d q auL |
HE / >>]
To locate
Press
a specific track directly
one of the DISC 1 to 3
buttons to select the CD
and a number button of the
track.
a point while listening to
the sound
Bi (forward) or 44
(backward) while playing
and hold down until you
find the point.
a point while observing
the display .
DD (forward) or FH
(backward) in pause and
hold down until you find
the point.
The CD Player | 13
A AA ARO
Ze
Playing tracks
repeatedly
(Repeat Play) PLAY MODE/ REPEAT BI
MONO/ST
You can play tracks repeatedly in
normal, shuffle or program play modes
(see pages 16 — 18.).
Playing a single CD repeatedly
Press REPEAT to display “REPEAT” in the
display.
2 Press DISC 1, 2, or 3 to select the CD to be played.
Playing two or three CDs repeatedly
1 Press REPEAT to display “ALL DISCS REPEAT”
in the display.
2 Press PI to start repeat play.
Playing tracks of a single CD in random order
repeatedly
1 Press PLAY MODE/MONO/ST until “SHUF”
appears in the display.
2 Press REPEAT to display “REPEAT” in the
display.
3 Press DISC 1, 2, or 3 to select the CD to be played.
14 | The CD Player
Playing tracks of two or three CDs in random
order repeatedly
Press PLAY MODE/MONO/ST until “ALL DISCS
SHUF” appears in the display.
2 Press REPEAT to display “REPEAT” in the
display.
3 Press PI to start repeat play.
Playing programmed tracks repeatedly
Program tracks (see page steps 1 — 3 on page 17).
2 Press REPEAT to display “REPEAT” in the
display.
3 Press PIN to start repeat play.
To cancel repeat play
Press REPEAT until “REPEAT” disappears in the
display.
The CD Player
19Ae|d q? 24 |
15
ое
A A
16
Playing tracks in
random order
(Shuffle Play) PLAY MODE/ DISC1-3 pI
MONO/ST
You can play tracks in random order.
Playing tracks of a single CD in random order
Press PLAY MODE/MONO/ST until “SHUF”
appears in the display.
2 Press DISC 1, 2, or 3 to select the CD to be played.
Playing tracks of two or three CDs in random
order
1 Press PLAY MODE/MONO/ST until “ALL DISCS
SHUF” appears in the display.
2 Press PIN to start shuffle play.
To cancel shuffle play
Press PLAY MODE/MONO/ST until “SHUF”
disappears in the display.
The CD Player
Creating your
own program
(Program Play)
You can make a program of up to 20
tracks from all the CDs in the order you
want them to be played.
Tips
You can select the track
on the player. Press
AMS/SEARCH << /
Bi then press
ENTER/ MEMORY
instead of the number
buttons.
You can play the same
program again, since
the program is saved
until you open the CD
tray.
You can record your
own program. After
you've created the
program, insert a blank
tape into deck B and
press € on deck B to
start recording.
и ON
FUNCTION MODE ¡POWER
HH MODE
DISC! DISC2 0563] DISC 1-3
| ME
=)
=
m
Mm
Number o
buttons a)
y
<
©
CLEAR
в
1 Press MODE until “ALL DISCS PGM” appears in
the display.
2 Press DISC 1 to 3 to select the CD.
3 Press the number buttons for the tracks you want
to program in the order you want. You can
program up to 20 tracks.
a
Ey
CD number oly re
Track number
Playing order
If you made a mistake, press CLEAR and re-enter
the track number.
To program additional tracks from another CD,
repeat steps 2 and 3.
4 Press B to start program play.
- continued
The CD Player | 17
- A. A — a ta dr A
18
Creating your own program (Program Play) (continued)
The CD Player
To cancel Program Play
Press MODE until “PGM” disappears in the display.
To check the order of tracks before play
Press ENTER/MEMORY on the player.
Every time you press the button, the track number
appears in the programed order.
To change the current program
To Do this
Erase the last track in 1 Press CLEAR. Every time you
the program press the button, the last track
in the program is cleared.
2 Re-enter the track numbers.
Change the whole Press M . Then create a new
program completely. program following the
programing procedure.
The Radio
Presetting radio
stations
You can store radio stations into the
player's memory. You can preset up to
20 radio stations, 10 for each FM or AM
in any order.
Tip
To preset radio stations
on the player, proceed
as follows:
1
Select the band and
tune in a station you
want.
Hold down ENTER /
MEMORY for about
2 seconds.
Decide on a preset
number for the
station (1 to 10) by
pressing PRESET
+/-.
Press ENTER/
MEMORY.
ATTY
и с,
FUNCTION MODE |POWER
DISC1 DISC2 DISC3
CD
D @ © НН
OS Ol number =
(7) (9) buttons 5
o
els :
DO CI |
© OS
BAND + + TUNE +/-
TUNE VOL
BAND
1 Press BAND until the band you want appears in
the display.
2 Tune in a station you want.
3 Hold down the number buttons that you want to
preset the new station for about 2 seconds.
The new station replaces the old one.
The Radio | 19
Playing preset
radio stations
Once you've preset the stations, use the
number buttons to tune in your favorite
stations.
Tip
You can tune in a
preset station with the
player. Use PRESET
+/— instead of the
number buttons.
20 | The Radio
rr
FUNCTION MODE {POWER
DISC1 DISC2 DISCS
QO) + (3)
© © © Number
@ (8) (9) buttons
ole
DO
OO CH
Co =) =) BAND
-
<
>
m
<
о
=
1 Press BAND to select FM or AM.
2 Press the number buttons to tune in a stored
station.
Setting Up
Hooking up the
system
Make sure you turn off the
power before making any
connections.
— Speaker terminals
Tips
® To detach the speakers,
slide the speaker box all
the way up and away
from the player.
* Connect the speakers
for this unit only to the
speaker terminals of
this unit. If you connect
any other speakers or
equipment,
' malfunction may occur.
Note
When transporting, make
sure to carry the player.
Do not carry the speakers
since they are not locked.
Surround speaker
(CFD-656 only)
» AM loop
aerial
Right
speaker
Speaker cords
Surround speaker
(CFD-656 only)
CFD-656
To a wall outlet
Hooking up the speakers
1 Align the grooves and slide the speaker box down
until it snaps into place.
|
Ln
yv
+
3
Ko
с
o
Left speaker
continued
Setting Up | 21
22
Hooking up the system (continued)
Setting Up
2 Connect the black wires to (-) minus and the red
wires to (+) plus terminals; the right speaker wires
to the R and the left speaker wires to the L
terminals.
Connecting surround speakers (CFD-656 only)
You can enjoy a rich and spacious effect by connecting
surround speakers.
Connect the black wires to (-) minus and the grey
wires to (+) plus terminals.
UR
Spp RO
+ 7 EAREND
To turn off the surround effect, disconnect the
surround speakers.
Hooking up the aerial
AM loop aerial (supplied)
AM EXT ANT
Reorient the aerial to improve broadcast reception.
Setting up the AM loop aerial
Connecting the AC power cord
Insert the AC power cord to the wall outlet.
Ed inserting batteries into the remote
Insert two size AA (R6) batteries (not supplied)
dn umes §
Replacing batteries
With normal use, the batteries should last for about six
months. When the remote no longer operates the
player, replace all the batteries with new ones.
Setting Up | 23
aa EL
Adjusting the
audio emphasis
(Sound Mode/MEGA BASS) MEGA BASS SOUND
You can adjust the audio emphasis of the
sound you are listening to.
Selecting the sound characteristic
Press SOUND to select the audio emphasis you want.
Choose To get
Normal mode The whole dynamic range for music
(no indication) such as classical music
== = Powerful, clean sounds, emphasizing
= = . .
Se low and high range audio.
1 3 1 1
— 111
un The presence of vocals, stressing
ps Pi middle range audio.
IEE IE IPE ONE IE
= Light, bright suonds emphasizing
Us high and middle range audio.
1 1 |
BEE FEE EEE EEE Sa
Reinforcing the bass sound
Press MEGA BASS.
“MEGA BASS” appears in the display. To return to
normal sound, press the button again.
24 | Setting Up
Additional Information
Precautions
On safety
As the laser beam used in the CD
player section is harmful to the eyes,
do not attempt to disassemble the
casing. Refer servicing to qualified
personne] only.
Should any solid object or liquid fall
into the player, unplug the player, and
have it checked by qualified personnel
before operating it any further.
On power sources
* For AC operation use the supplied AC
power cord; do not use any other type.
* The player is not disconnected from
the AC power source (mains) as long
as it is connected to the wall outlet,
even if the player itself has been
turned off.
Unplug the player from the wall outlet
when it is not to be used for an
extended period of time.
When the batteries are not to be used,
remove them to avoid damage that
can be caused by battery leakage or
corrosion.
The nameplate indicating operating
voltage, power consumption, etc. is
located at the rear.
On placement
Do not leave the player in a location
near heat sources, or in a place subject
to direct sunlight, excessive dust or
mechanical shock.
Do not place the player on an inclined
or unstable place.
Do not place anything within 10 mm
of the side of the cabinet. The
ventilation holes must be
unobstructed for the player to operate
properly and prolong the life of its
components. : .
If the player is left in a car parked in
the sun, be sure to choose a location in
the car where the player will not be
subjected to the direct rays of the sun.
Since a strong magnet is used for the
speakers, keep personal credit cards
using magnetic coding or spring-
wound watches away from the player
to prevent possible damage from the
magnet.
When you move the player, be sure to
first remove the CD(s), otherwise, you
may not be able to take out the CD(s)
later or trouble with the unit may
occur.
continued
Additional Information
25
——]i— dalla
26
Precautions (continued)
On operation
* If the player is brought directly from a
cold to a warm location, or is placed in
a very damp room, moisture may
condense on the lens inside the CD
player section. Should this occur, the
player will not operate properly. In
this case, remove the CD and wait
about an hour for the moisture to
evaporate.
* Tf the player has not been used for a
long time, set it in the playback mode
to warm it up for a few minutes before
inserting a cassette.
If you have any questions or problems
concerning your player, please consult
your nearest Sony dealer.
Notes on CDs
* Before playing, clean the CD with a
cleaning cloth. Wipe the CD from the
center out.
¢ Do not use solvents such as benzine,
thinner, commercially available
cleaners or anti-static spray intended
for vinyl LPs.
e Do not expose the CD to direct
sunlight or heat sources such as hot
air ducts, nor leave it in a car parked
in direct sunlight as there can be a
considerable rise in temperature
inside the car.
Additional Information
* Do not stick paper or sticker on the
CD, nor scratch the surface of the CD.
* After playing, store the CD in its case.
If there is a scratch, dirt or fingerprints
on the CD, it may cause tracking error.
Notes on cassettes
e Break off the cassette tab from side A
or B to prevent accidental recording. If
you want to reuse the tape for
recording, cover the broken tab with
adhesive tape.
S Side A
76
д
Tab for side А
Tab for side B
To record on a tape with its tab broken
off, cover the respective tab hole for
side A or B with adhesive tape.
* The use of a cassette with more than
90 minutes of play time is not
recommended except for long,
continuous recording or playback.
Troubleshooting
Symptom
Remedy
The power is not on. .
Connect the AC power cord to a wall outlet
securely.
There is no audio. e
General
.
Make sure the function you want to use appears
in the display window.
Adjust the volume.
Unplug the headphones when listening through
speakers.
“no disc” lights in the display even
when a CDis in place.
* Insert the CD with the label surface up.
The CD does not play. °
my -
CD Player
Make sure that the CD tray is closed.
Place the CD with the label surface up.
Clean the CD.
Take out the CD and leave the CD tray open for
about an hour to dry moisture condensation.
Make sure “CD” appears in the display.
The sound drops out.
Reduce the volume.
Clean the CD, or replace it if the CD is badly
damaged
Place the player in a location free from
vibration.
The audio is weak or has poor
quality. .
Radio
Move the player away from the TV.
If you are using the remote while listening to
AM radio, noise may be heard. This is
unavoidable.
The picture of your TV becomes *
unstable.
If you are listening to an FM program near the
TV with an indoor antenna, move the player
. away from the TV.
continued
27
Additional Information
mbm ma te pdr te de}
Troubleshooting (continued)
Symptom
Remedy
Tape Player
The tape does not move when you
press an operation button.
Close the cassette compartment securely.
The REC @ button does not
function /The tape does not play.
Make sure the safety tab on the cassette is in
place.
Make sure “TAPE” appears in the display.
The tape does not erase completely.
Clean the erasing head (see page 29.)
The tape does not record.
Make sure. the tape is inserted properly.
Make sure the safety tab of the cassette is in
place.
The audio is weak/ The audio
quality is poor.
Clean the heads, pinch rollers and capstans (See
page 29).
Demagnetize the heads using a demagnetizer
(see page 29).
The sound is distorted.
The TYPE II (high position) or TYPE IV (metal)
tape is being used. Use TYPE I (normal) tape
only.
Remote
The remote does not function.
Replace all the batteries in the remote with new
ones if they are weak.
Make sure that you are pointing the remote at
the remote sensor on the player.
Remove any obstacles in the path of the remote
and the player.
Make sure the remote sensor is not exposed to
strong light such as direct sunlight or
fluorescent lamp light.
Move closer to the player when using the
remote.
Others
There is no surround effect (CFD-
656 only).
Connect two supplied surround speakers.
The player uses a built-in micro computer for its various operations. Due to change in power
supply conditions, etc., operation way sometimes become unstable. After trying the above
remedies, if the player still does not function properly, press RESET at the rear with a pointed
material. If the problem persists, please consult your nearest Sony dealer.
Additional Information
Maintenance
Cleaning the tape heads and tape
path
Wipe the heads, the pinch rollers and
the capstans with a cleaning swab
slightly moistened with cleaning fluid or
alcohol after every 10 hours of operation
for optimum playback and recording
quality. To make the best possible
recording, however, we recommend that
you clean all surfaces over which tape
travels before each recording.
Deck A
rf — -
Playback head Capstan
|
( Pinch roller
. )
Record/playback head Capstan
a)
| i
_ Erase head Pinch roller
After cleaning, insert a tape when the
areas cleaned are completely dry.
Demagnetizing the tape heads
After 20 to 30 hours of use, enough
residual magnetism will have built up
on the tape heads to begin to cause loss
of high frequency sound and hiss. At
this time, you should demagnetize the
heads and all metal parts in the tape
path with a commercially available tape
head demagnetizer. |
Cleaning the cabinet
Clean the cabinet, panel and controls
with a soft cloth slightly moistened with
a mild detergent solution. Do not use
any type of abrasive pad, scouring
powder, or solvent, such as alcohol or
benzine.
Additional Information
29
pr EA
Specifications
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
With 3.2-ohm loads, both channel driven
from 150 — 8,000 Hz; rated 4 W per channel-
minimum RMS power, with no more than
10 % total harmonic distortion in AC
operation,
Other Specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm ,
Emission duration: Continuous
Laser output: Less than 44.6 hW
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)
Spindle speed
200 r/ min (rpm) to 500 r/min (rpm} (CLV)
Number of channels
2
Frequency response
20-20,000Hz +1/-2dB
Wow and flutter
Below measurable limit
Radio section
Frequency range
FM: 87.6 - 108 MHz
АМ: 530 - 1,710 kHz
Aerials
FM: Telescopic aerial
AM: External aerial terminal
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 140 s (sec.) with Sony cassette C-60
Frequency response
TYPE I (normal): 80 — 10,000 Hz
Additional information
General
Speaker
Full range: 10 cm (4 in.) dia.
3.2 ohms, cone type (2)
Surround speaker (CFD-656 only)
10 em (4 in.) dia., 8 ohms, cone type (2)
Outputs
Headphones jack (stereo minijack):
For 16 - 64 ohms impedance headphones
Speaker terminals: For supplied 3.2 homs
impedance speaker
Surround speaker terminals (CFD-656 only):
Terminals for supplied 8 ohms impedance speaker
Power output (excluding US model)
4.3 W + 4,3 W (at 3.2 ohm, 10 % harmonic
distortion)
Power requirements
For CD radio cassette-corder:
120 V AC, 60 Hz
For remote:
3 V DC, 2 size AA (R6) batteries
Power consumption
AC27 W
Dimensions
Approx. 646 x 286.5 x 355 mm (w/h/d)
(25 4x11 %x 14 inches) (incl. projecting parts)
Mass
Approx. 10.5 kg (23 1b. 2 02)
Supplied accessories
Remote contro! (1)
AM loop aerial (1)
Surround speakers (2) (CFD-656 only)
Design and specifications are subject to change without
notice.
Optional accessories
Sony MDR headphone series
Index
A
Audio emphasis 24
B
Batteries for remote 23
С
CD player 12
Cleaning
cabinet 29
tape heads and tape
path 29
Connecting
AC power cord 23
speakers 21
Creating your own program
17
D, E, F, G, H
Demagnetizing the tape
heads 29
Display 12
LJ. K
Improving broadcast
reception 7
L
Listening to the radio 6
Locating a specific track 13
М, № О
MEGA BASS 24
P,Q
Playing
aCD 4
a tape 8
preset radio stations 20
tracks repeatedly 14
Presetting radio stations 19
Program Play 17
R
Radio stations
playing 20
presetting 19
Recording
on a tape 10
Repeat Play 14
S
Selecting
audio emphasis 24
tracks 13
Setting up 21
Shuffle Play 16
Sound mode 24
SORROUND 22
T
Troubleshooting 27
U, V, W, X, Y, Z
Using the display 12
Additional Information
31
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement