MP Series Modulating Plus Brochure
MP SERIES Modulating Plus Tube Heater
Detroit Radiant Products Company
MP Series Product Specifications
ELECTRICAL
Input Range:
80,000 to 200,000 BTU/h
Lengths:
25-70 Ft.
• 120V, 60Hz, 3-wire.
• 4.8A starting, 1.1A running.
Gas Type:
Natural or Propane
INTERNAL CONTROLS
Combustion Chamber:
Aluminized or Titanium Stabilized Steel
Radiant Tubes:
Aluminized Steel
Certification:
CSA Design Certified, ANSI Z83.20b
Limited Warranty:
1-5-10 (Components-Tubes-Burner)
learning control logic.0
TUBE CONSTRUCTION
emissive black tube coating.
Turbulator baffles.
Stainless Steel Upgrades: Available
Standard
Protective Guards:
Available (PG)
Side Shield Extensions:
Available (SSE)
Outdoor Approval:
Available (OD-KIT)
VENTING
• 4” single vent.
• 6” common vent.
• Consult factory for additional
venting options.
• Highly polished aluminum.
• Continuous overlap design.
• Reflector end caps.
• Rotatable 0° to 45°.
• Anti-rattle tension springs.
COMBUSTION AIR
KIT CONTENTS
• Preset 4 in. air inlet collar.
• Sidewall or roof intake ready.
MP Series
ModulatingPlus Tube Heater
INLET GAS PRESSURE
(Inches W.C.)
Manifold @ Min. Rate:
1.65 Nat. Gas; 4.10 LP.
Manifold @ Max. Rate:
4.80 Nat. Gas; 11.0 LP.
Min Inlet: 6.0 Nat. Gas; 12.0 LP.
Max. Inlet: 14.0 Nat. Gas; 14.0 LP.
REFLECTORS
Available (RUP, REP)
Indicator Lights:
• Hot surface ignition.
• Flame rod sense.
• Self-diagnostic LED.
• As shown at left.
• 4 in. dia., 16 ga. construction. GAS CONNECTION
• Interlocking swaged tube design. • 36” x 3/4” S.S. Flexible Gas
• All tubes treated with .95 highly Connector.
MP Series Optional Equipment
U or L Configurations:
• 100% safety shut-off.
• Microprocessor with self-
IGNITION/SENSE
•
•
•
•
• All hangers & tube couplers.
• User manual(s) and application
guidelines.
AVAILABLE MP Series MODELS & CLEARANCES
Model#
Gas*
MP-25-80
MP-30-80
MP-30-115
MP-40-80
MP-40-115
MP-40-150
MP-50-115
MP-50-150
MP-50-200
MP-60-150
MP-60-200
MP-70-200
N or LP
N or LP
N or LP
N or LP
N or LP
N or LP
N or LP
N or LP
N or LP
N or LP
N or LP
N or LP
Blast
Standard
Mode Rate Modulating
(MBH)
range (MBH)
85
85
120
85
120
155
120
155
200
155
200
200
52 - 80
52 - 80
75 - 115
52 - 80
75 - 115
97.5 - 150
75 - 115
97.5 - 150
130 - 194
97.5 - 150
130 - 194
130 - 194
Length
26’-5”
31’-5”
31’-5”
41’-1”
41’-1”
41’-1”
50’-9”
50’-9”
50’-9”
60’-5”
60’-5”
70’-1”
Mounting
Weight Heights**
145 lbs.
160 lbs.
160 lbs.
190 lbs.
190 lbs.
190 lbs.
235 lbs.
235 lbs.
235 lbs.
265 lbs.
265 lbs.
300 lbs.
12’ to 20’
12’ to 20’
14’ to 22’
12’ to 20’
15’ to 25’
15’ to 28’
15’ to 28’
17’ to 30’
19’ to 37’
17’ to 32’
19’ to 37’
19’ to 42’
* Specify natural (N) or propane (LP) gas.
** Factory recommended mounting heights are provided as a guideline. Actual conditions may
dictate variations from the above data.
Re-Verber-Ray® is a registered trademark of Detroit Radiant Products Company. Due to
continuous product innovation, Detroit Radiant Products Company reserves the right to
change product specifications without prior notice.
0° Mounting Angle
45° Mounting Angle
0° W/ 1 Side Shield
0° W/ 2 Side Shields
MP CLEARANCES TO COMBUSTIBLES (IN.)
SIDE
MOUNT
ANGLE FRONT BEHIND TOP BELOW
MODEL NO.
MP (25,30,40)-80 [N,P]
0º
14
14
6
66
45º
39
8
10
66
W/1 side shield
0º
29
8
6
66
W/2 side shields
0º
16
16
6
66
20 ft. from burner
0º
7
7
6
30
MP (30,40,50)-115 [N,P]
0º
20
20
6
76
45º
58
8
10
76
W/1 side shield
0º
42
8
6
76
W/2 side shields
0º
20
20
6
76
20 ft. from burner
0º
7
7
6
30
MP (40,50,60)-150 [N,P]
0º
24
24
6
83
45º
58
8
10
83
W/1 side shield
0º
42
8
6
83
W/2 side shields
0º
23
23
6
83
20 ft. from burner
0º
11
11
6
46
MP (50,60,70)-200 [N,P]
0º
41
41
6
100
45º
63
8
10
100
W/1 side shield
0º
54
8
6
100
W/2 side shields
0º
30
30
6
100
20 ft. from burner
0º
11
11
6
50
Clearances published in MP Series manual and on warning label
supersede data shown on this brochure. Reference MP Series
installation manual for complete information.
The ONLY Infrared Heater that Puts YOU in Control!
The MP Series fully modulating infrared heater is the only infrared heater
that allows you to select the desired performance curve that best suits your building
requirements.
Detroit radiant products co.
DISTRIBUTED BY:
IRSC
INFRA-RED HEATER SAFETY COUNCIL
21400 Hoover Rd.
Warren, MI 48089-3162
Phone: (586) 756-0950
Toll Free: (800) 222-1100
Fax: (586) 756-2626
Email: [email protected]
Website: www.reverberray.com
LBMP-3M-3/14 (AOG)
Patent Pending
Global Provider of Energy Efficient Heating Solutions Since 1955
MP Series Modulating Plus Tube Heater
MP Series Quality Construction Features
The MP Series by Detroit Radiant Products Company raises the bar with modulating
technology. This full air and gas modulation line of heaters incorporates cutting edge
technology such as the selection of three different performance curves as well as a
‘Blast Mode’™ feature for extreme environmental demands.
Patent Pending
Sealed black enameled steel burner control box with 3-piece
independent ABS plastic compartment cover provides ease in servicing.
Fitted ABS plastic
collar for connection
to 4” air intake pipe.
Highly polished aluminum
reflectors with tube hangers.
MP Series Unique Operational Features
Blast
Mode
• ‘Blast Mode’™ feature allows the user to temporarily lock the heater into its
Burner and hot-surface
igniter inspection sight glass.
highest input plus an extra 5,000 BTU’s for extreme environmental demands.
100%
Normal Modulating Range
• Choose from three performance modes.
• Models range from 80,000 to 200,000 BTU’s.
• Full gas modulation with corresponding air flow modulation to achieve
optimal fuel utilization and comfort levels.
• Forced high-fire start up for faster response to the environmental demand.
• Full proportional-integral-derivative (PID) logic to reduce on/off cycles over
traditional heat.
MP Series Advanced Controller Options
Loaded with powerful custom features, the Premium User Interface (PUI) is an advanced
microprocessor smart logic controller that offers the optimal performance out of your MP Series
heater. It modulates heater(s) with full PID control that considers various inputs and outputs.
Other Control Options:
65%
MP Series Performance Curves / Mode Selection
The MP Series is programmed to operate on several performance curves allowing the user to select the desired operation that best
accommodates their specific needs.
Choose from:
Building Management System (BMS)*
Premium User Interface Module
PUI module
Used to control the MP Series via 4-20ma, 0-10vdc, or dry contacts.
*Some BMS control schemes require the use of the Premium User Interface (PUI) module.
Performance Curves
Temperature
‘Standard Mode’: Unit operates as
a balance between Comfort Mode
and Economy Mode. It is intended
to provide a system that is moderately thermal efficient
while still minimizing the greater temperature differentials
associated with economy mode.
‘Economy Mode’: Unit operates to maximize thermal
efficiency. It is designed to provide a system that is more
thermally efficient than the other modes due to quicker
dissipation of heat.
Least
Temperature
Differential
Average
Greatest
Temperature Temperature
Differential Differential
Master Unit
Potentiometer
Used to control the MP Series in outdoor or spot heating
environments to allow the user to manually control the heater’s firing
rate based on the dial position.
Distance from Burner
FAN
SYSTEM
ON AUTO COOL OFF HEAT
Mode Selection / Application Chart
Comfort
• Patios
• Loading docks
• Break areas and lunch rooms
• Kennels
• Parts counters and service desks
• Golf driving ranges
• Woodworking shops
Standard Mode
• Service garages
• Fire Stations
• Populated warehouse heating
• Manufacturing
• Auto showrooms
Economy Mode
• Aircraft hangars
• Car washes
• Pole barns
• Foundries
• Unpopulated warehouses
Additional “Slave” Unit(s)
up to 256 total units per temperature zone
‘Comfort Mode’: Unit operates to
minimize temperature differentials
across the length of the heater. It is
intended to provide a system that
has a greater perceived comfort than
the other modes due to more even
dissipation of heat.
Black-coated, slip-fit
radiant emitter tubes.
Single-Stage Thermostat
Used to control the MP Series in the most simplistic form.
External Thermistor
Optionally may be used in conjunction with a single-stage thermostat
to better meet the demands of the space.
MP Series Modulating Plus Tube Heater
MP Series Quality Construction Features
The MP Series by Detroit Radiant Products Company raises the bar with modulating
technology. This full air and gas modulation line of heaters incorporates cutting edge
technology such as the selection of three different performance curves as well as a
‘Blast Mode’™ feature for extreme environmental demands.
Patent Pending
Sealed black enameled steel burner control box with 3-piece
independent ABS plastic compartment cover provides ease in servicing.
Fitted ABS plastic
collar for connection
to 4” air intake pipe.
Highly polished aluminum
reflectors with tube hangers.
MP Series Unique Operational Features
Blast
Mode
• ‘Blast Mode’™ feature allows the user to temporarily lock the heater into its
Burner and hot-surface
igniter inspection sight glass.
highest input plus an extra 5,000 BTU’s for extreme environmental demands.
100%
Normal Modulating Range
• Choose from three performance modes.
• Models range from 80,000 to 200,000 BTU’s.
• Full gas modulation with corresponding air flow modulation to achieve
optimal fuel utilization and comfort levels.
• Forced high-fire start up for faster response to the environmental demand.
• Full proportional-integral-derivative (PID) logic to reduce on/off cycles over
traditional heat.
MP Series Advanced Controller Options
Loaded with powerful custom features, the Premium User Interface (PUI) is an advanced
microprocessor smart logic controller that offers the optimal performance out of your MP Series
heater. It modulates heater(s) with full PID control that considers various inputs and outputs.
Other Control Options:
65%
MP Series Performance Curves / Mode Selection
The MP Series is programmed to operate on several performance curves allowing the user to select the desired operation that best
accommodates their specific needs.
Choose from:
Building Management System (BMS)*
Premium User Interface Module
PUI module
Used to control the MP Series via 4-20ma, 0-10vdc, or dry contacts.
*Some BMS control schemes require the use of the Premium User Interface (PUI) module.
Performance Curves
Temperature
‘Standard Mode’: Unit operates as
a balance between Comfort Mode
and Economy Mode. It is intended
to provide a system that is moderately thermal efficient
while still minimizing the greater temperature differentials
associated with economy mode.
‘Economy Mode’: Unit operates to maximize thermal
efficiency. It is designed to provide a system that is more
thermally efficient than the other modes due to quicker
dissipation of heat.
Least
Temperature
Differential
Average
Greatest
Temperature Temperature
Differential Differential
Master Unit
Potentiometer
Used to control the MP Series in outdoor or spot heating
environments to allow the user to manually control the heater’s firing
rate based on the dial position.
Distance from Burner
FAN
SYSTEM
ON AUTO COOL OFF HEAT
Mode Selection / Application Chart
Comfort
• Patios
• Loading docks
• Break areas and lunch rooms
• Kennels
• Parts counters and service desks
• Golf driving ranges
• Woodworking shops
Standard Mode
• Service garages
• Fire Stations
• Populated warehouse heating
• Manufacturing
• Auto showrooms
Economy Mode
• Aircraft hangars
• Car washes
• Pole barns
• Foundries
• Unpopulated warehouses
Additional “Slave” Unit(s)
up to 256 total units per temperature zone
‘Comfort Mode’: Unit operates to
minimize temperature differentials
across the length of the heater. It is
intended to provide a system that
has a greater perceived comfort than
the other modes due to more even
dissipation of heat.
Black-coated, slip-fit
radiant emitter tubes.
Single-Stage Thermostat
Used to control the MP Series in the most simplistic form.
External Thermistor
Optionally may be used in conjunction with a single-stage thermostat
to better meet the demands of the space.
MP SERIES Modulating Plus Tube Heater
Detroit Radiant Products Company
MP Series Product Specifications
ELECTRICAL
Input Range:
80,000 to 200,000 BTU/h
Lengths:
25-70 Ft.
• 120V, 60Hz, 3-wire.
• 4.8A starting, 1.1A running.
Gas Type:
Natural or Propane
INTERNAL CONTROLS
Combustion Chamber:
Aluminized or Titanium Stabilized Steel
Radiant Tubes:
Aluminized Steel
Certification:
CSA Design Certified, ANSI Z83.20b
Limited Warranty:
1-5-10 (Components-Tubes-Burner)
learning control logic.0
TUBE CONSTRUCTION
emissive black tube coating.
Turbulator baffles.
Stainless Steel Upgrades: Available
Standard
Protective Guards:
Available (PG)
Side Shield Extensions:
Available (SSE)
Outdoor Approval:
Available (OD-KIT)
VENTING
• 4” single vent.
• 6” common vent.
• Consult factory for additional
venting options.
• Highly polished aluminum.
• Continuous overlap design.
• Reflector end caps.
• Rotatable 0° to 45°.
• Anti-rattle tension springs.
COMBUSTION AIR
KIT CONTENTS
• Preset 4 in. air inlet collar.
• Sidewall or roof intake ready.
MP Series
ModulatingPlus Tube Heater
INLET GAS PRESSURE
(Inches W.C.)
Manifold @ Min. Rate:
1.65 Nat. Gas; 4.10 LP.
Manifold @ Max. Rate:
4.80 Nat. Gas; 11.0 LP.
Min Inlet: 6.0 Nat. Gas; 12.0 LP.
Max. Inlet: 14.0 Nat. Gas; 14.0 LP.
REFLECTORS
Available (RUP, REP)
Indicator Lights:
• Hot surface ignition.
• Flame rod sense.
• Self-diagnostic LED.
• As shown at left.
• 4 in. dia., 16 ga. construction. GAS CONNECTION
• Interlocking swaged tube design. • 36” x 3/4” S.S. Flexible Gas
• All tubes treated with .95 highly Connector.
MP Series Optional Equipment
U or L Configurations:
• 100% safety shut-off.
• Microprocessor with self-
IGNITION/SENSE
•
•
•
•
• All hangers & tube couplers.
• User manual(s) and application
guidelines.
AVAILABLE MP Series MODELS & CLEARANCES
Model#
Gas*
MP-25-80
MP-30-80
MP-30-115
MP-40-80
MP-40-115
MP-40-150
MP-50-115
MP-50-150
MP-50-200
MP-60-150
MP-60-200
MP-70-200
N or LP
N or LP
N or LP
N or LP
N or LP
N or LP
N or LP
N or LP
N or LP
N or LP
N or LP
N or LP
Blast
Standard
Mode Rate Modulating
(MBH)
range (MBH)
85
85
120
85
120
155
120
155
200
155
200
200
52 - 80
52 - 80
75 - 115
52 - 80
75 - 115
97.5 - 150
75 - 115
97.5 - 150
130 - 194
97.5 - 150
130 - 194
130 - 194
Length
26’-5”
31’-5”
31’-5”
41’-1”
41’-1”
41’-1”
50’-9”
50’-9”
50’-9”
60’-5”
60’-5”
70’-1”
Mounting
Weight Heights**
145 lbs.
160 lbs.
160 lbs.
190 lbs.
190 lbs.
190 lbs.
235 lbs.
235 lbs.
235 lbs.
265 lbs.
265 lbs.
300 lbs.
12’ to 20’
12’ to 20’
14’ to 22’
12’ to 20’
15’ to 25’
15’ to 28’
15’ to 28’
17’ to 30’
19’ to 37’
17’ to 32’
19’ to 37’
19’ to 42’
* Specify natural (N) or propane (LP) gas.
** Factory recommended mounting heights are provided as a guideline. Actual conditions may
dictate variations from the above data.
Re-Verber-Ray® is a registered trademark of Detroit Radiant Products Company. Due to
continuous product innovation, Detroit Radiant Products Company reserves the right to
change product specifications without prior notice.
0° Mounting Angle
45° Mounting Angle
0° W/ 1 Side Shield
0° W/ 2 Side Shields
MP CLEARANCES TO COMBUSTIBLES (IN.)
SIDE
MOUNT
ANGLE FRONT BEHIND TOP BELOW
MODEL NO.
MP (25,30,40)-80 [N,P]
0º
14
14
6
66
45º
39
8
10
66
W/1 side shield
0º
29
8
6
66
W/2 side shields
0º
16
16
6
66
20 ft. from burner
0º
7
7
6
30
MP (30,40,50)-115 [N,P]
0º
20
20
6
76
45º
58
8
10
76
W/1 side shield
0º
42
8
6
76
W/2 side shields
0º
20
20
6
76
20 ft. from burner
0º
7
7
6
30
MP (40,50,60)-150 [N,P]
0º
24
24
6
83
45º
58
8
10
83
W/1 side shield
0º
42
8
6
83
W/2 side shields
0º
23
23
6
83
20 ft. from burner
0º
11
11
6
46
MP (50,60,70)-200 [N,P]
0º
41
41
6
100
45º
63
8
10
100
W/1 side shield
0º
54
8
6
100
W/2 side shields
0º
30
30
6
100
20 ft. from burner
0º
11
11
6
50
Clearances published in MP Series manual and on warning label
supersede data shown on this brochure. Reference MP Series
installation manual for complete information.
The ONLY Infrared Heater that Puts YOU in Control!
The MP Series fully modulating infrared heater is the only infrared heater
that allows you to select the desired performance curve that best suits your building
requirements.
Detroit radiant products co.
DISTRIBUTED BY:
IRSC
INFRA-RED HEATER SAFETY COUNCIL
21400 Hoover Rd.
Warren, MI 48089-3162
Phone: (586) 756-0950
Toll Free: (800) 222-1100
Fax: (586) 756-2626
Email: [email protected]
Website: www.reverberray.com
LBMP-3M-3/14 (AOG)
Patent Pending
Global Provider of Energy Efficient Heating Solutions Since 1955
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement