USER MANUAL
USER MANUAL
VDTU-101/201
VDSL 4-band CO/CPE Modem
VDSL 4-Band CO/CPE MODEM
VDSL Point to Point Solution
The VDTU-101/201 works as Ethernet to/from VDSL subscriber-site conversion bridge. The
VDTU-101/201 uses QAM-based 4-band VDSL technologies. Which supports max distance
1.9Km (6333ft) at 5M/5M or 1.3Km (4333ft) at 15M/15M, or 800m(2666ft) at 25M/25M
symmetrical data service. The VDTU-201 also works with VRM-308/VRM-324 VDSL IP
DSLAM, together to form a cost-effective solution for services such as remote lecturing,
telemedicine, video conferencing, Video-on-Demand (VoD), IP-TV etc. Internet access, and
various high-speed data applications.
The front-panel provides LED indications of system and interface status. The built-in
POTS/ISDN splitter allows a standard POTS phone or ISDN device to be connected. Full or
half-duplex mode of LAN operations is automatically sensed and configured. VDSL link rates
are configured by local Modem or IP DSLAM over auto speed function.
Therefore, VDTU-101/201 supports auto-speed, plug & play operations on the subscriber-site,
and are part of an ideal solution for delivering cost-effective, high-performance
broadband/multimedia services to Multi-Dwelling Units (MDU) and Multi-Tenant Units (MTU)
environments such as hotels, campus, hospitals and telecom.
1
Table of Contents
1.Unpacking Information ............................................................................................. 3
Check List ................................................................................................................... 3
2. Installation............................................................................................................... 3
Hardware Installation .................................................................................................. 3
2.1 Pre-installation Requirements ..........................................................................3
General Rules ........................................................................................................4
Connecting the Modem..........................................................................................4
Connecting the RJ-11/RJ-45 ports .........................................................................4
3.Hardware Description
Front Indicators………………………………………………………………….…6
Rear Connectors………………………………………………………………......7
Left Side Connector…………………………………………………………….…7
Power On…………………………………………………………………….….…7
4.Firmware Description………………………………………………………….….8
Appendix A Cable Requirement………………………………………………..…..9
Appendix B Product Features & Specifications……………………………….…10
Appendix C Trouble shooting………………………………………………….…..12
Appendix D Compliance and Safety Information…………………………….….15
FCC/CE Warning……………………………………………………………………15
Warranty……………………………………………………………………………..16
VDSL 4-band Modem Manual
1. Unpacking Information
Check List
Carefully unpack the package and check its contents against the checklist.
Package Contents
z VDSL 4-Band Modem (VDTU-101 for CO side/ VDTU-201 for CPE side)
z Four plastic feet
z User Manual & Utility
z AC To DC Power Adapter
z RJ-45 cable
z RJ-11 cable
z RJ-45 To D-SUB Cable(Option)
Please inform your dealer immediately for any missing, or damaged parts. If
possible, retain the carton, including the original packing materials, Use them to
repack the unit in case there is a need to return for repair.
2. Installation
Hardware Installation
This chapter describes how to install the VDTU-101 & 201 MODEM and establishes
network connections. You may install the VDTU1-101 & 201 MODEM on any level
surface (e.g, a table or shelf). However, please take note of the following minimum site
requirements before you begin.
2.1 Pre-installation Requirements
Before you start actual hardware installation, make sure you can provide the right
operating environment, including power requirements, sufficient physical space, and
proximity to other network devices that are to be connected. Verify the following
installation requirement:
z Power requirements: DC5V/1A or above.
z The VDTU-101 & 201 MODEM should be located in a cool dry place, with at least
10cm/4in of space at the front and back for ventilation.
z Place the VDTU-101 & 201 MODEM out of direct sunlight, and away from heat
sources or areas with a high amount of electromagnetic interference.
z Check if network cables and connectors needed for installation are available
3
CTC Union Technologies Co., Ltd
VDSL 4-band Modem Manual
General Rules
Before making any connections to the MODEM, note the following rules:
zEthernet Port (RJ-45)
All network connections to the Modem Ethernet port must be made using Category
5 UTP for 100Mbps; Category 3,4 UTP for 10Mbps
No more than 100 meters of cabling may be use between the MUX or HUB and an
end node.
zPhone Port (RJ-11)
All Phone set connections to the RJ-11 Port made using 24~26 Gauge phone wiring.
Connecting the MODEM
The Modem has one Ethernet port which support connection to Ethernet operation. The
devices attached to these ports must support auto-negotiation or 10Base-T OR
100Base-TX unless they will always operate at half duplex.
Use any of the Ethernet ports to connect to devices such as NIC, Switch, bridge or router.
You can also connect to another compatible Modem to an RJ-45 port on the other device.
The RJ11 Line port is used to connect to the wall RJ-11 modular socket (outlet) which is
connect to VDSL 4-Band CPE Modem side (Point to point solution)
The RJ11 Phone port of the Modem can connected to a telephone and a computer sharing
one telephone wire for making calls and accessing the internet at the same time.
Connecting the RJ-11/RJ-45 Ports
1. The Modem’s RJ-11 ports supports max distance 1.9Km at 5M/5M or max speed
25M/25M symmetrical and distances up to 800m data service across existing
phone wiring, without interfering with standard voice transmissions, easy-to-use
does not require the installation of any additional wiring. Every RJ-11 modular
phone jack in the home can become a port on the LAN. Networking devices can be
installed on a single telephone wire that can span within 1.9Km or 800m (depend
on speed) between the two farthest points. (Figure 1.0).
2.
VDTU-101/201 Modem has embedded Splitter between every VDSL side (Line) and
POTS (Phone) side. It permit you to deliver broadband service on the same lines as
Plain Old Telephone Service (POTS), PBX, ISDN traffic and VDSL Signal.
4
CTC Union Technologies Co., Ltd
VDSL 4-Band CO/CPE MODEM
3.The RJ-11 port support max distance 1.9Km at 5M/5M or max speed 25M/25M
symmetrical and distances up to 800m data service. When inserting a RJ-11 plug,
be sure the tab on the plug clicks into position to ensure that it is properly seated.
4.Do not plug a RJ-11 phone jack connector into the Ethernet port (RJ-45 port). This
may damage the modem. Instead, use only twisted-pair cables with RJ-45
connectors that conform to Ethernet standard.
Notes:
1.Be sure each twisted-pair cable (RJ-45) does not exceed 100 meters (333 feet).
2.RJ-11 port use 24 ~ 26 gauge phone wiring, we do not recommend 28 gauge or
above.
3.We advise using Category 3,4,5 cable for Cable Modem or Router connections to
avoid any confusion or inconvenience in the future when you upgrade attached to
high bandwidth devices.
4.Be sure phone cable has been installed when VDTU-101 and VDTU-201 will be
power on.
5
CTC Union Technologies Co., Ltd.
VDSL 4-Band CO/CPE MODEM
3. Hardware Description
This section describes the important parts of the VDTU-101 & 201 MODEM. It features
the front indicators and rear connectors.
Front Indicators
The following figure shows the front panel.
Figure Chapter 2.1 VDTU-101 Modem
Figure Chapter 2.2 VDTU-201 Modem
At a quick glance of the front panel, it is easy to tell if the CO Modem has power,
if it has signal from its Ethernet RJ-45 port and if there is phone line signal on RJ-11
port.
Front Indicators
LED Description and Operation
The Modem has three LED indicators.
LEDs
Status
PWR
(Power LED)
Steady
Green
It will light up (ON) to show that the product is power good,
and system reset OK.
Ethernet
(Ethernet LED)
Steady Green
Flashing (LINK/ACT)
Each RJ45 station port on the Ethernet is assigned an LED
light for monitoring port “Good Linkage”. LED is normally
OFF after the power on operation, but will light up steadily to
show good linkage and flashing to show data transmission.
Steady Green
RJ11 station port on the VDSL is assigned an LED light for
monitoring port “Good Linkage”. LED is normally OFF after
the power on operation, but will light up steadily to show
good linkage.
LINK
(VDSL LED)
Descriptions
6
CTC Union Technologies Co., Ltd.
VDSL 4-band Modem Manual
Rear Panel
The following figure shows the rear connectors
Figure Chapter 2.3 Rear Connectors
VDTU-101/201 &CPE MODEM Rear Connectors
Description
Connectors
Type
Line
For connecting to the VDSL Modem Using
a RJ-11 cable
RJ-11
Phone
For connecting to the telephone or Fax、ISDN Modem
RJ-11
Ethernet
For connecting to a Ethernet equipped device
RJ-45
Left side view
The following figure shows the left side connectors. You can firmware upgrade and
Monitor VDSL status over console port (VDTU-101 only).
Figure Chapter 2.4 Left side Connector
Table Modem Rear Connectors:
Connector
Console port
Description
Type
For connecting to PC with RS-232 serial port over
a RJ-45 To D-SUB Cable
RJ-45
Power On
1. Check the adapter is properly connected.
2. Verify the power LED is steadily on.
7
CTC Union Technologies Co., Ltd
VDSL 4-band Modem Manual
4. Firmware Description
„
Auto Speed function description.
VDTU-101 is a 4band VDSL solution which supports auto speed function, they can
support 5M/15M/25M symmetrical data service depend on installing environment, they
will do auto speed function while phone cable be re-plug in between VDTU-101 and
VDTU-201, or both be re-power on. VDTU-101 will try to link with 25M/25M mode first, if
link fail will auto speed down to 15M/15M mode second, and if link fail again will auto
speed down to 5M/5M, then stay on this mode until re-plug in phone cable or re-power on
both.
„
Speed mode limitation :
5M/5M mode within 1.9km (6333ft)
15M/15M mode within 1.3km (4333ft)
25M/25M mode within 800m (2666ft)
Note : We recommend phone cable which must meet Cat. 3 standard or above and
without clustering, otherwise the above guarantee will be void.
„
Engineering Functions :
These functions is for maintaining and troubleshooting such as firmware upgrade,
command line, SNR indicator, Ethernet and VDSL port setting and status monitor
and so on. And it is supporting plug and play, so end user doesn’t have to need it.
8
CTC Union Technologies Co., Ltd
VDSL 4-band Modem Manual
Appendix A: Cable Requirements
A CAT 3,4 or 5 UTP (unshielded twisted pair) cable is typically used to connect the Ethernet
device to the Modem. A 10Base-T cable often consists of four pairs of wires, two of which are
used for transmission. The connector at the end of the 10Base-T cable is referred to as an
RJ-45 connector and it consists of eight pins. The Ethernet standard uses pins 1,2,3 and 6 for
data transmission purposes.
PIN
1
2
3
4
5
6
7
8
MNEMONIC
TX+
TXRX+
NC
NC
RXNC
NC
Table
FUNCTION
Ethernet differential Transmit signal(+)
Ethernet differential Transmit signal(-)
Ethernet differential receive signal(+)
Unused
Unused
Ethernet differential receive signal(-)
Unused
Unused
RJ-45 Ethernet Connector Pin
out Assignments
Standard telephone wire of any gauge or type-flat, twisted or quad is used to connect the
Modem to the telephone network. A telephone cable typically consists of three pairs of wires,
one of which is used for transmission. The connector at the end of the telephone cable is
called an RJ-11 connector and it consists of six pins. POTS (plain old telephone services) use
pins 3 and 4 for voice transmission. A telephone cable is shown below.
A
B
Figure:Telephone cable
The A and B connectors on the rear of the Modem are RJ-11 connectors. These connectors
are wired identically. The RJ-11 connectors have six positions, two of which are wired .The
Modem uses the center two pins. The pin out assignment for these connectors is presented
below.
Pin#
MNEMONIC
FUNCTION
1
NC
Unused
2
NC
Unused
3
TIP
POTS
4
RING
POTS
5
NC
Unused
6
NC
Unused
Table
RJ-11 Pin
out Assignments
9
CTC Union Technologies Co., Ltd
VDSL 4-band Modem Manual
Appendix B: Product Features & Specification
Product Name:VDTU-101/201
Features:
● Compliant with IEEE802.3 10BASE-T standard.
● Compliant with IEEE802.3u 100BASE-TX standard.
● Compliant with ETSI, ITU, ANSI standards
● Max distance 5M/5M distance up to 1.9km(6333ft)
15M/15M distance up to 1.3km(4333ft)
Max speed 25M symmetrical and distances up to 800m(2666ft).
● Supports 1 * RJ-11 connector for Ethernet over VDSL.
● Supports 1 * RJ-11 connector for telephone/PBX connection.
● Supports 1 * RJ-45 port for 10/100Mbps Ethernet with Auto MDI/MDIX.
● Supports Auto-speed and full duplex for VDSL port.
● Supports long packet size up to 1536 bytes
● Supports POTS/ISDN voice pass.
● Supports 4wires phone set pass through.
● Supports console port for firmware upgrade and maintain (LT only).
● Voice and Data work on the same telephone line.
● Spectral compatibility with xDSL, ISDN (2B1Q/4B3T).
● Supports flow control IEEE802.3x for Full Duplex & Back Pressure for Half Duplex.
● Supports Surge protection.
● Provides Power LED.
● Provides LED indication Link/Active Status for Ethernet port and Link for VDSL port.
● External switching power adapter Input: AC 85-240 volts/50-60Hz; Output: DC 5V/1A or
above.
● Mini size and metal case design
10
CTC Union Technologies Co., Ltd
VDSL 4-band Modem Manual
Specifications:
● Standard
IEEE802.3 standard
IEEE802.3u standard
Compliant with ETSI, ITU, ANSI standards
● Interface
●
●
●
●
●
●
●
●
●
1 * RJ-45 10/100Mbps Ethernet port
1 * RJ-11 connector for EoVDSL
1 * RJ-11 connector for telephone connection
Console port: RS-232C / 19200bps(VDTU-101 only)
Cable Connections
RJ-45 (Ethernet): Category 3, 4, 5 UTP/STP
RJ-11 (EoVDSL): Twisted-Pair phone wire
Provides LED indication Link/Active Status for Ethernet port and Link for VDSL port.
VDSL Frequency Spectrum:
VDTU-101_ Transmitter: 900 KHz ~ 3.9MHz
Receiver: 4MHz & 7.9MHz
VDTU-201_ Transmitter: 4MHz ~ 7.9MHz
Receiver: 900 KHz ~ 3.9M
POTS/ISDN pass filter Spectrum: 0 ~ 120K
Power Consumption: VDTU-101(LT): 5.4W / VDTU-201(NT): 6W.
Operating Temperature: 0°C ~ 50°C (41F ~ 122F)
Storage Temperature: -20°C ~ 65°C (-4F ~ 149F)
Humidity: 10 to 90% (non-condensing)
Dimensions: 95 x 110 x 24 mm(3.74" x 4.33" x 0.94").
11
CTC Union Technologies Co., Ltd
VDSL 4-band Modem Manual
Appendix C: Troubleshooting
Diagnosing the Modem’s Indicators
The Modem can be easily monitored through its comprehensive panel indicators. These
indicators assist the network manager in identifying problems the hub may encounter. This
section describes common problems you may encounter and possible solutions
1.
Symptom: Power indicator does not light up (green) after power on.
Cause: Defective External power supply
Solution: Check the power plug by plugging in another that is functioning properly.
Check the power cord with another device. If these measures fail to resolve the
problem, have the unit power supply replaced by a qualified distributor.
2.
Symptom: Link indicator does not light up (green) after making a connection.
Cause: Network interface (e.g, a network adapter card on the attached device),
network cable, or switch port is defective.
Solution: Power off and re- power on the VDSL Modem.
Verify that the switch and attached device are powered on.
Be sure the cable is plugged into both the switch and corresponding device.
Verify that the proper cable type is used and its length does not exceed specified
limits.
Check the Modem on the attached device and cable connections for possible
defects.
Make sure phone wire must be connected between VDTU-101 and VDTU-201 first,
when both are be power on.
Replace the defective Modem or cable if necessary.
3.
Symptom: VDSL Link cannot be established
Cause: VDSL auto speed failure, or phone cable length is over specification with
the limit of 1.9km or not a 24 gauge phone wire with twist pair.
Solution:
3.1 Please make sure phone wire must be connected between VDTU-101 and
VDTU-201 when both are power on. VDTU-101 will do auto speed function
depending on phone wire length, therefore if VDTU-101 can’t detect VDTU-201
over phone wire while both power on, this will cause the link to fail.
3.2 Please check phone cable must be 24 gauge with twist pair and without rust,
and the length is not over 1.9km.
Note : Phone cable must meet Cat. 3 standard or above and without clustering,
otherwise will cause more cross talk issue to reduce VDSL power driver.
12
CTC Union Technologies Co., Ltd
VDSL 4-band Modem Manual
4.
Symptom: VDSL always Link on 5M/5M speed mode at short phone cable.
Cause: VDSL auto speed stop.
Solution: Please re-plug in phone cable between VDTU-101 and VDTU-201, or
re-power on VDTU-101 and VDTU-201 again.
Note : VDTU-101 will do auto speed function while phone cable re-plug in or
re-power on.
5.
Symptom: We tested with a regular S0 bus from an NTBA - data works, but ISDN
telephone does not.
Solution: You must connect according to the following chart if you want to connect
CO and CPE with NTBA.
Power and Cooling Problems
If the POWER indicator does not turn on when the power cord is plugged in, you may
have a problem with the power outlet, power cord, or internal power supply as explained
in the previous section. However, if the unit power is off after running for a while, check
for loose power connections, power losses or surges at the power outlet, and verify that
the fan on back of the unit is unobstructed and running prior to shutdown. If you still
cannot isolate the problem, then the internal power supply may be defective. In this case,
contact your dealer.
Installation
Verify that all system components have been properly installed. If one or more
components appear to be malfunctioning (e.g., the power cord or network cabling), test
them in an alternate environment where you are sure that all the other components are
functioning properly.
13
CTC Union Technologies Co., Ltd
VDSL 4-band Modem Manual
Transmission Mode
The default method of selecting the transmission mode for RJ-45 ports is 10/100 Mbps
ETHERNET, for RJ-11 port are 5/15/25Mbps VDSL. Therefore, if the Link signal is
disrupted (e.g., by unplugging the network cable and plugging it back in again, or by
resetting the power), the port will try to reestablish communications with the attached
device via auto-negotiation. If auto-negotiation fails, then communications are set to half
duplex by default. Based on this type of industry-standard connection policy, if you are
using a full-duplex device that does not support auto-negotiation, communications can be
easily lost (i.e., reset to the wrong mode) whenever the attached device is reset or
experiences a power fluctuation. The best way to resolve this problem is to upgrade
these devices to a version that support Ethernet and VDSL.
Physical Configuration
If problems occur after altering the network configuration, restore the original connections,
and try to track the problem down by implementing the new changes, one step at a time.
Ensure that cable distances and other physical aspects of the installation do not exceed
recommendations
System Integrity
As a last resort verify the switch integrity with a power-on reset. Turn the power to the
switch off and then on several times. If the problem still persists and you have
completed all the preceding diagnoses, then contact your dealer
14
CTC Union Technologies Co., Ltd
VDSL 4-band Modem Manual
Appendix D:Compliance and Safety Information
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a computing device,
pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
1.
2.
3.
4.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
The equipment and the receiver should be connected to outlets on separate circuits.
Consult the dealer or an experienced radio/television technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
If this telephone equipment causes harm to the telephone network, the telephone company
will notify you in advance that temporary discontinuance of service may be required. But if
advance notice isn’t practical, the telephone company will notify the customer as soon as
possible. Also, you will be advised of your right to file a complaint with the FCC if you believe
it is necessary.
The telephone company may make changes in its facilities, equipment, operations or
procedures that could affect the proper functioning of your equipment. If they do, you will be
notified in advance in order for you to make necessary modifications to maintain uninterrupted
service.
This equipment may not be used on coin service provided by the telephone company.
Connection to party lines is subject to state tariffs.
15
CTC Union Technologies Co., Ltd
VDSL 4-Band CO/CPE MODEM
Important Safety Instructions
Caution:The direct plug-in wall transformer serves as the main disconnect for the
product. The socket outlet shall be installed near the product and be readily
accessible.
Caution:Use only the power supply included with this product. In the event the power
supply is lost or damaged:In the United States, use only with CSA certified or
UL listed Class 2 power supply, rated 5Vdc 1A or above.
IN Europe, use only with CE certified power supply, rated 5Vdc 1A or above.
Do not use this equipment near water, for example in a wet basement.
Avoid using a telephone during an electrical storm. There may be a remote risk of
electrical shock from lightning.
Do not use the telephone to report a gas leak in the vicinity of the leak.
If trouble is experienced with this unit, please contact customer service at the address
and phone listed below. Do not disassemble this equipment. It does not contain any user
serviceable components.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CE Mark Warning
This is a CE class A product. In a domestic environment, this product may cause radio
interference in which case the user may be required to take adequate measures.
16
CTC Union Technologies Co., Ltd.
VDSL 4-band Modem Manual
Warranty
The original owner that the product delivered in this package will be free from defects in
material and workmanship for one year parts after purchase.
There will be a minimal charge to replace consumable components, such as fuses,
power transformers, and mechanical cooling devices. The warranty will not apply to any
products which have been subjected to any misuse, neglect or accidental damage, or
which contain defects which are in any way attributable to improper installation or to
alteration or repairs made or performed by any person not under control of the original
owner.
The above warranty is in lieu of any other warranty, whether express, implied, or statutory,
including but not limited to any warranty of merchantability, fitness for a particular
purpose, or any warranty arising out of any proposal, specification, or sample. Shall not
be liable for incidental or consequential damages. We neither assumes nor authorizes
any person to assume for it any other liability.
Note: Please do not tear off or remove the warranty sticker as shown, otherwise
the warranty will be void.
17
CTC Union Technologies Co., Ltd
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement