8E1 + 1Ethernet Fiber Optical Multiplexer

8E1 + 1Ethernet Fiber Optical Multiplexer
SNR-MPX-8E1-SFP
8E1 + 1Ethernet Fiber Optical Multiplexer
8E1 + 1Ethernet Fiber Optical Multiplexer
User’s Manual
SNR-MPX-8E1-SFP
8E1 + 1Ethernet Fiber Optical Multiplexer
To users:
:
Thank you for using our products. Before using, please read this Reference Manual
carefully, and keep properly.
Alarm
1. This product cannot be caught in or be affected with damp, for they can make the
performance degressive and even broken.
2. Before fixing this product, please check the model and according to the User s’
Reference Manual.
6/5/2009
Shop.Nag.Ru
Page 1 of 16
SNR-MPX-8E1-SFP
8E1 + 1Ethernet Fiber Optical Multiplexer
Contents
CHAPTER 1 GENERAL INTRODUCTION........................................ 3
1.1 PRODUCT DESCRIPTION ............................................................................. 3
1.2 PRINCIPLE CHART AND DESCRIPTION.......................................................... 3
1.2.1 Description ........................................................................................ 4
1.3 CHARACTERS............................................................................................ 4
CHAPTER 2 FUNCTIONS
.......................................................... 5
2.1 FRONT PANEL ........................................................................................... 5
2.1.1 LED................................................................................................... 5
2.1.2 Buttons in front panel ........................................................................ 6
2.1.3 Hot line phone (optional port)............................................................ 6
2.1.4 Front panel DIP definition ................................................................. 7
2.2 REAR PANEL ............................................................................................. 8
2.2.1 Power Supply.................................................................................... 9
2.2.2 Ethernet (optional component).......................................................... 9
2.2.3 Fiber interface ................................................................................. 10
2.2.4 E1 interface (75Ω:BNC) .......................................................... 10
CHAPTER 3 PARAMETERS AND INDEX ...................................... 11
3.1 PARAMETERS.......................................................................................... 11
3.1.1 Fiber interface ................................................................................. 11
3. 1.2 E1 interface.................................................................................... 11
3.1.3 10/100Base-T Port .......................................................................... 11
3.2 DIMENSION ............................................................................................. 11
3.3 POWER SUPPLY....................................................................................... 11
3.4 OPERATION CONDITION ........................................................................... 12
CHAPTER 4 OPERATION ........................................................ 13
4.1 EQUIPMENT INSTALLATION ....................................................................... 13
4.2 QUICK INSTALLATION ............................................................................... 13
4.3 CAUTIONS ABOUT INSTALLATION .............................................................. 14
CHAPTER 5 PACKAGE ........................................................... 15
6/5/2009
Shop.Nag.Ru
Page 2 of 16
SNR-MPX-8E1-SFP
8E1 + 1Ethernet Fiber Optical Multiplexer
CHAPTER 1. GENERAL INTRODUCTION
1.1 Product Description
8E1 + 1Ethernet Fiber Optical Multiplexer can multiplex to 8 E1 signals for transmission
over an optical fiber, resulting in reaching a longer distance without a repeaters and superior
performance compared to copper media.
8E1 + 1Ethernet Fiber Optical Multiplexer is the 8E1 point-to-point optical transport
equipment that uses the FPGA chips and it is easy to upgrade. It is single board structure
and the largest transmission capacity is 8E1. The outer design use the standard 19 inches
rack, so the volume is little, weight is light and operation is convenient and credit.
8E1 + 1 Ethernet Fiber Optical Multiplexer uses the PDH fiber transmission technologies.
The 2Mbps (E1) interfaces can connect with the exchanger, light loop device and
multi-diplexer directly to the special network. Complete alarm function for 8E1 Fiber Optical
Multiplexer, it is stable and easy to maintenance, install and small in size. It has one digital
service telephone.
1.2 Principle Chart and Description
Fig1. PDH principle chart
6/5/2009
Shop.Nag.Ru
Page 3 of 16
SNR-MPX-8E1-SFP
8E1 + 1Ethernet Fiber Optical Multiplexer
1.2.1 Description
Device adopts veneer structure, and can be distinguished according to the functions into 5
parts: A. 2/8 combine unit, B. encode/decode unit, C. hot line unit, D. monitoring system, E.
second power. A, B and E are the basic parts, achieving reverse conversion from 4
2048kbit/s signals to laser signal. C and D are of assistant.
1.3 Characters
•
Base on IC of independence intellectual property rights
•
Adopt veneer structure
•
Offer 1-8 × 2Mb/s digital interfaces
•
Up to 8 E1 links on one fiber
•
One link to service telephone for duty contract
•
Provides 1 channel of 10M/100M, support VLAN setting.
•
One channel OA for optional.
•
When fiber signal is loss, users can distinguish whether the remote device is power
off or the fiber line is down from the indicator status on the local device.
•
180-260VAC & -48VDC power options and the positive and negative of DC-48V can
be optional because there is the self-test circuit for the polarity inside th1e device
•
Standard 19 inches rack, little volume, light weight, steady capacity and convenient
setup
6/5/2009
Shop.Nag.Ru
Page 4 of 16
SNR-MPX-8E1-SFP
8E1 + 1Ethernet Fiber Optical Multiplexer
CHAPTER 2. FUNCTIONS
2.1 Front Panel
Fig2. Sketch map of the front panel
2.1.1 LED
Name
Color
Status
Describe
LOS
Red
Active
E1 signal loss
Red
Active
Optical Signal lost
Red
Flick
OLOS
2time/sec.: the remote device is
power off
OLOF
Red
Active
Optical SYNC loss
LE
Red
Active
Total alert when any alert in local
E3
Red
Active
Optical BER≥10-3
F2
Green
\
\
PWR
Green
Active
Power on
LINK
Green
Active
LAN Link and Active
SPD
Green
Active
On:100M,OFF:10M
Note: If the function is defined as 4E1/2E1, then LOS5-8/LOS3-8 is ineffective.
6/5/2009
Shop.Nag.Ru
Page 5 of 16
SNR-MPX-8E1-SFP
8E1 + 1Ethernet Fiber Optical Multiplexer
2.1.2 Buttons in front panel
PUSH
OFF
ON
MSK
DIP1-5 be used E1 warning shield
DIP1-5 be used E1 remote loop
MUTE
(standalone) warning voice is on
(standalone) warning voice is off
LRS
LED means Local
LED means Remote
PH
Hot line phone not used
Use Hot line phone
2.1.3 Hot line phone (optional port)
Hot line phone, not occupy 2Mbps channel transmission.
On the front panel there is a “PH” button, press on the “PH” button on the remote site it
will sound.
To answer it the remote site just need to press the “PH” button on the remote unit, the
alarm will cut off and just plug in the phone both side able to do the communication.
Setting of the manage phone.
•
It does not occupy the 2M circuits
1 2 3
4
pin
6/5/2009
definition
description
1
MIC-
MIC input -
2
SPEAKER+
Loudhailer output +
3
SPEAKER-
Loudhailer output -
4
MIC+
MIC input +
Shop.Nag.Ru
Page 6 of 16
SNR-MPX-8E1-SFP
8E1 + 1Ethernet Fiber Optical Multiplexer
2.1.4 Front panel DIP definition
On the front panel of standalone / card in rack, the SW5 DIP definition shows as follows:
When MSK button pushes up, (RLOOP1-8): 1-8 E1 remote loop. If the RLOOP1 is ON,
this means that at the far end it is doing a E1 loop-back
0 means ON,1 means OFF
The Remote x E1 Loop
1
2
3
4
5
6
7
8
All 8E1 Loop
E1 not Loop
MSK button
push up
push up
push up
push up
push up
push up
push up
push up
push up
push up
Bit1
0
0
0
0
0
0
0
0
0
Bit2
0
0
0
0
0
0
0
1
0
Bit3
Bit4
0
0
0
1
0
1
1
0
1
0
1
1
1
1
0
0
0
0
other units
Bit5
1
0
1
0
1
0
1
0
0
Table 1
When MSK button push down, Bit1-5(mask1-5) mean 1-8E1 warning shielding.
1 means OFF, 0 means ON
Shielding E1
6/5/2009
MSK button
Bit1
Bit2
Bit3
Bit4
Bit5
channel
contort
8
push down
0
1
0
0
1
7-8
push down
0
1
0
1
0
Shop.Nag.Ru
Page 7 of 16
SNR-MPX-8E1-SFP
8E1 + 1Ethernet Fiber Optical Multiplexer
6-8
push down
0
1
0
1
1
5-8
push down
0
1
1
0
0
4-8
push down
0
1
1
0
1
3-8
push down
0
1
1
1
0
2-8
push down
0
1
1
1
1
1-8
push down
1
0
0
0
0
E1 not shielding
push down
Other units
Bit 6 : reserved.
Bit-7: ON: fiber interface local loop
Bit-8:
OFF: Cancel the loop
ON: The Ethernet interfaces are logically separated.
OFF: The Ethernet interfaces are exchangeable.
2.2 Rear panel
Sketch map of rear panel for 75Ω
Sketch map of rear panel for 120Ω
Note: If the function is defined as 4E1/2E1, then No.5-8/ No.3-8 E1 ports are ineffective.
6/5/2009
Shop.Nag.Ru
Page 8 of 16
SNR-MPX-8E1-SFP
8E1 + 1Ethernet Fiber Optical Multiplexer
2.2.1 Power Supply
Support AC220V and DC-48V
•
AC220V: 180-260VAC, directly insert power wire;
•
-48VDC: the positive and negative of DC-48V can be optional because there is the
self-test circuit for the polarity inside the device
2.2.2 Ethernet (optional component)
This model can offer 1-4 channels for 10/100M, full/duplex auto-negotiation LAN
interface, support VLAN protocol, this interface can continuous learn MAC addresses in
the LAN that connected with it, and send the address as frame in another LAN.
Transparence to TCP/IP protocol, offers security connection between different equipments
in the network, used widely in network connection and monitor between WAN and LAN.
•
10/100 Base-T Ethernet port parameter
•
Rate: 10M or 100M, full/semi duplex self adaption.
•
Ethernet rate in optical line: 100Mbps.
•
Protocol: support IEEE 802.3, IEEE 802.1Q(VLAN)
•
MAC address table: can learn 4096 MAC address
•
Ethernet buffer memory: 64 Mbits SDRAM
•
Physical interface: RJ45 slot, support AUTO-MDIX
Ethernet operating diagrammatic:
6/5/2009
Shop.Nag.Ru
Page 9 of 16
SNR-MPX-8E1-SFP
8E1 + 1Ethernet Fiber Optical Multiplexer
Ethernet RJ45 ports connection:
There are 2 light upon per RJ45.LNK on means that LAN Link and Active; SPD on means
that ETH of 100M; SPD off means that ETH of 10M.
2.2.3 Fiber interface
There is SFP slot on the rear panel, supporting standard SFP module.
)
2.2.4 E1 interface (75Ω/ BNC or 120Ω/ RJ45)
75Ω:
“ RXD”means 75Ω(BNC)unbalance E1 input, namely E1(2M)
signal input
“TXD”means 75Ω(BNC)unbalance E1 output, namely E1(2M)
signal output.
120Ω: 8 E1interface adopt RJ45, support 120Ω balance connection.
6/5/2009
pin
definition
description
1
TX+
E1 output +
2
TX-
E1 output-
4
RX+
E1input +
5
RX-
E1 input-
Shop.Nag.Ru
Page 10 of 16
SNR-MPX-8E1-SFP
8E1 + 1Ethernet Fiber Optical Multiplexer
CHAPTER 3. PARAMETERS AND INDEX
3.1 Parameters
3.1.1 Fiber interface
Optical interface: SFP lot (insert SFP module)
3. 1.2 E1 interface
Interface code:
HDB3 code
Line speed:
2.048Mbp/s ±50ppm
Interface standard:
ITU-T G 703
Interface impedance:
75Ω/unbalanced (BNC)
120Ω/balanced (RJ45)
Allowed attenuation:
0~6dBm
3.1.3 10/100Base-T Port
Rate:
10/100M, full/duplex auto-negotiation
Protocol:
Support IEEE 802.3, IEEE 802.1Q (VLAN)
MACAddress Entiries:
4096Entiries
Connector:
RJ45
3.2 Dimension
485 mm(L)×140 mm(W)× 44 mm(H)
3.3 Power supply
AC220V:input voltage AC 180V~260V
DC-48V:input voltage -36V~-72V
6/5/2009
Shop.Nag.Ru
Page 11 of 16
SNR-MPX-8E1-SFP
8E1 + 1Ethernet Fiber Optical Multiplexer
3.4 Operation Condition
Voltage:
AC180V ~ 260V; DC –48V; DC +24V
Consumption:
≤5W
Operating temperature:
0°C~50°C
Storing temperature:
-40°C~+70°C
Relative humidity:
95 %
Without disturbance of erosive and solvent gas, raising dust or strong magnetic field
6/5/2009
Shop.Nag.Ru
Page 12 of 16
SNR-MPX-8E1-SFP
8E1 + 1Ethernet Fiber Optical Multiplexer
CHAPTER 4. OPERATION
4.1 Equipment installation
After unpacking and before installation, make sure checking the following:
•
Make sure the package is well. If the package is damaged, contact service office
quickly for solution.
•
Check the package according to the product list, if find equipment severe damaged
or lack of some components, please contact installation worker or service office of
us.
•
Check whether the equipment type meets with the type you ordered.
•
Check whether the component is in integrity.
•
Check the power supply type.
4.2 Quick installation
•
Fasten the Equipment in 19 inch rack with the screws in the equipment package.
•
Use reliable ground connection at GND point of the equipment
•
Use power tab to connect power according to the manual, don’t exchange the
polarities.
•
Create user equipment connecting wire according to your demand (2M, V.35 and 10
Base-T), then connected, don’t exchange receive and transfer wires.
•
Connect SFP module to the SFP lot, make sure the optical fiber head is clean and
connection well. (fiber bending radius≥50 mm)
•
Use multimeter to test power polarity and voltage, make sure it matches with
equipment requirement.
•
After complete installation and make sure it’s ok, power on the switch. Check
indicator light meet with practice situation (see related part of manual).
6/5/2009
Shop.Nag.Ru
Page 13 of 16
SNR-MPX-8E1-SFP
8E1 + 1Ethernet Fiber Optical Multiplexer
•
A clean, steady environment and firm installation should be provided for desktop or
wall hanging equipment.
4.3 Cautions about installation
Avoid severe liberation and mechanical damage during the process of delivering
and installation.
Arrange fiber appropriately, fiber bending radius≥50 mm.
Check voltage and polarity meet with back panel, or it will cause permanent damage
to the equipment.
The installation location should be convenient for personal passing and equipment
movement.
The environment should be dry, clean and ventilated well.
Essential static-protective is needed during the installation and maintenance, ground
the chassis to increase anti-interference capability and prevent lightning strike.
Before use the equipment, independence work ground and protect ground should
provided, make sure it ground well.
6/5/2009
Shop.Nag.Ru
Page 14 of 16
SNR-MPX-8E1-SFP
8E1 + 1Ethernet Fiber Optical Multiplexer
CHAPTER 5. PACKAGE
Contents in each box:
Fiber Optical Multiplexer ………………………………1
AC220V Power wire……………………………………1
User’s manual………………………………………….1
Note:
:
•
Fiber Optical Multiplexer is a sensitive electronic item, please do handle with care
when carrying or delivering and pay attention to against humidity.
•
Within the warranty period, whenever there is a problem regarding the quality issue,
we will take the responsibility for it and repair will done by us Free of Charge.
•
After the warranty period, we will charge accordingly depending on the fault or
damage.
•
Whenever there is a malfunction of product, try to identify the problem according to
alarm and contact our technical support in time.
6/5/2009
Shop.Nag.Ru
Page 15 of 16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement