File - Unmanned Tech Blog
X160
User Manual
Declaimers and warmings
Thank you for purchasing X160.
Please read this instruction manual carefully before using this product. By using this product, you hereby
agree to this disclaimer and signify that you have read it in full.
Please mount and use this product as per this manual strictly. As manufacturer has no control over use,
setup, final assembly, modification (including use other parts such as motor, ESC, propeller etc),no ability
shall be assumed nor accepted for any resulting damage or injury.
As it may cause wireless interference in the living environment, please take effective measures to avoid it.
Any parts of this manual is subjected to change without prior notice.
Any problems while mounting this frame, please contact with us or authorised agent.
Introduction
X160 is a micro racing frame for FPV Player. It is a highly integrated product with highly flexible controls.
Combo with motor 1104-4000KV, propeller 3x2" as well as the popular 10A esc with BLHeli firmware(
support ONESHOT). Flight range of remote control more than 1000 meters.
To gain the quality and real-time shoot for FPV, X160 also combines 5.8G 32CH 200mW transmitter with 1/3"
CMOS lens, which supports 127 or wider 160° shootings and every moment brings you the exciting FPV
experience.
The default firmware of FC is CleanFlight, It can be used after connected the battery, receiver and set the
remote control. X160 supports to be flashed Openpilot firmware also, there will be show the different
experience for you!
I
~
|
Y
X160 Power Set
Flight control | CC3D( Pre-tuned CF firmware)
Propeller | 3x2"
28 ESC |10A (BLHeli FW)
- Motor | 1104/4000KV
Th | Battery —|11.1V/3S (RCMD)
ON
E
Cognition X160
Box list
X160 frame 1pcs
Propeller 3020 2paris
5.8G antennas 1pcs
Screw M2x6 for propeller 10pcs
3020 Propeller
1/3"
Main board connection
ESC connection for left arm
Switch frequency selection for dip switch
Dial switch 12345 to choose the required FR/CH for 32 channels.
FR
— TI
Сл
pC =>
wl >
ol
"
0
N
- 1
NE
“LI
<
< НИ
тп
A
w
- 1
NC]
w_ 15
=_
o
x
~
- 1
NE
© 15
> ]1—
o
CH
wi
SNC]
a 1
N
o
SNC]
a
I
o
co
a
оС
©
+
wl
>]
a 1
— O |. ©
Син == |на =
CON [oC =
will]
SC]
;
E07 © |— ME о
VON 5 | CN
co CT
SC]
al 1
—CN CO |-CHO
SIE SED
oo
SC
о! С
—-н о |-
SEC] | EC]
SS
al
O
I
CH1
CH2
CH3
CH4
CH5
CH6
CH7
5865M
5845M
5825M
5805M
5785M
5765M
5745M
5725M
FR
5733M
5752M
5771M
5790M
5809M
5828M
5847M
5866M
5705M
5685M
5665M
5645M
5885M
5905M
5925M
5945M
5740M
5760M
5780M
5800M
5820M
5840M
5860M
5880M
Installation
1. Mount the 5.8G antennas as picture shows.
2. Mount the propeller properly as below picture shows.
Connection diagram
[1] [2] [3]
4]
5
6
В
Front
[4]
[5]
o
[15]
i
17
18
Back
1]Solder pad for esc signal wire
[19]
2]Positive solder pad for battery voltage
4]Negative solder pad for esc signal
[1]
[2]
[3]Negative solder pad for battery voltage
[4]
[9]
5]Solder pad for motor
Back
[20]
[21]
[1] Negative solder pad for esc signal
[2] Solder pad for esc signal wire
[3] Positive solder pad for battery voltage
[4] Solder pad for esc signal wire
[5] Negative solder pad for esc signal
[6] Negative solder pad for battery voltage
[7] +5V
[8] GND
[9] 5.8G frequency-selection dial switch
[10] 5.8G antennas pedestal
[11] Solder pad for esc signal wire
[12]Negative solder pad for esc signal
[13]Negative solder pad for esc signal
[14]Solder pad for esc signal wire
[15]Positive solder pad for battery voltage
[16]Negative solder pad for battery voltage
[17]+5V
[18]GND
[19]5V UBEC
[20]Positive solder pad for battery voltage
[21]Negative solder pad for battery voltage
[112] [3]
1]Negative solder pad for battery voltage
Front
[5]
O_O
>
Back
we JUÁBL 10) UONISULOS JSF
2 Negative solder pad for esc signal
4|Solder pad for esc signal wire
[1]
[2]
[3]Positive solder pad for battery voltage
[4]
[5]
5]Solder pad for motor
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement