Oxymatic 500 Series User Manual

Oxymatic 500 Series User Manual
Models 511, 511WG, 512, 523
PRODUCT
INFORMATION
AND
INSTRUCTIONS
TABLE OF CONTENTS
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important Safety Rules and Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Description of Parts and Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
Assembly and Use
Non-Portable Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing the System (CGA 870 Models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installing the System (CGA 540 Model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Oxygen Cylinder Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Classifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Specifications and Symbols Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Important Information to Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
1
GENERAL INFORMATION
This manual provides information necessary to operate the CYPRESS OXYPneumatic®
conserver with built-in regulator.
The CYPRESS conservers can be used with CGA 870 or CGA 540 cylinders at home or
away from home to provide your specific oxygen requirements.
• CGA 870 Valve (Models 511, 511WG, and 512)
• CGA 540 Valve (Model 523)
Statements in this manual preceded by the following words are of special significance:
WARNING
Indicates there is a possibility of injury to you or others.
CAUTION
Indicates there is a possibility of damage to the device or to other property.
NOTE
Indicates points of particular interest or emphasis that allow for more efficient and
convenient operation of the equipment.
2
IMPORTANT SAFETY RULES & PRECAUTIONS
WARNING:
• Read and understand this manual before operating your CYPRESS OXYPneumatic
oxygen conserver.
• This device is not intended for use during sleep or by patients who:
- Breathe more than 40 breaths/minute,
- Consistently fail to trigger equipment (e.g., mouth breathers).
Smoking near oxygen equipment is strictly prohibited. Keep cigarettes,
matches, burning tobacco, and open flames, such as lighted candles, away from
the area where the system is being stored or operated.
• Avoid creation of any spark, such as static electricity caused by any type of
friction, near oxygen equipment.
*
NOTE: Oxygen will not burn; however, it does vigorously accelerate the burning of
any flammable material.
• Never use oil, grease, or petroleum-based products on or near the system.
Please wash and dry your hands properly prior to operating your oxygen
equipment.
• Never use aerosol sprays near the equipment.
• Not suitable for use in the presence of flammable anesthetic mixture.
• Be sure to turn off oxygen supply by closing the cylinder valve when not in use.
• Use cannula tubing no longer than 7 feet (2.13m).
• Do not use mask, pediatric, or other low-flow cannula tubing when operating the
unit.
3
IMPORTANT SAFETY RULES & PRECAUTIONS
CAUTION:
• Federal (USA) law restricts this device to sale by or on the order of a physician.
• Prevent water or other liquid substances from entering the unit
• Prevent dust or any small particles from entering the unit
• Do not expose the unit to extreme temperatures
• Always maintain a backup supply of oxygen
• Do not use humidifier bottles
• Do not use if leaking or damaged
• Refer repairs to authorized service personnel
*
NOTE: Oxygen supplied by this equipment is supplemental only and is not intended
for life support applications. The CYPRESS conserver should not be used to supply
anything other than medical oxygen.
Please contact your Home Care Provider if you have any questions.
4
INTRODUCTION
The CYPRESS OXYPneumatic oxygen conserver includes a combination of a lowpressure regulator and an oxygen conserver, designed for use with a cylinder as an
ambulatory oxygen system. It is capable of delivering a precise amount of supplemental
oxygen at the optimal point in the breathing cycle. The CYPRESS conserver greatly
increases the efficiency in the delivery of oxygen, maximizing the beneficial effects and
eliminating unnecessary oxygen waste.
When we breathe, approximately one-third of the time is spent inhaling and two-thirds
exhaling. As a result, oxygen delivered by continuous flow is wasted during exhalation.
By eliminating oxygen flow during exhalation, a two-thirds savings is possible. Additionally,
the oxygen available during the very first part of inhalation contributes most to meeting
oxygen needs. The CYPRESS conserver takes advantage of these facts to provide
maximum efficiency in the delivery of oxygen. This device is designed to be an integral
component of a lightweight, long-lasting ambulatory oxygen system.
5
DESCRIPTION OF PARTS & CONTROLS
CGA 870 Models
• Cylinder Adjustment Knob: This is used to attach the
unit to any CGA 870 post-valve cylinder.
• Oxygen Pressure Gauge*: Enables the user to monitor
the contents of the compressed oxygen cylinder and
is protected by a rubber guard. (Does not apply to
Model 511WG.)
• Selector Switch**: Enables the user to select the desired
setting, as well as “OFF” and "CF" (continuous flow).
When not in use, the switch should be turned to the
"OFF” position.
Cylinder
Adjustment
Knob
Oxygen
Pressure
Gauge
With
Rubber
Guard*
Selector
Switch**
CGA 870
Seal
Cylinder
Alignment
Pins
Vent
Hole
Oxygen
Supply
Outlet
• Oxygen Supply Outlet: Use this fitting to attach a
standard cannula.
• Cylinder Alignment Pins: When assembling the unit, these
parallel pins must be inserted into the holes on the CGA 870
post valve.
• CGA 870 Seal [Gasket, FR-870G, viton or equivalent]:
Creates the interface between the post valve and the
CYPRESS conserver. Besides offering a rugged interface,
it also surrounds the oxygen path in a ring of stainless steel
or brass.
• Vent Hole: Maintains proper internal pressure. Do not obstruct
with any object, such as a label or tight-fitting carrying bag.
WARNING: Use only a manufacturer specified gasket.
6
FIGURE A
CYPRESS OXYPneumatic Conserver
with CGA 870 Connection
(Model 511 shown here)
*Model 511WG does not have a
gauge.
**Selector switch settings will vary
according to model (see specifications on page 17).
DESCRIPTION OF PARTS & CONTROLS
CGA 540 Model
• Connector: The end of this component mates with the cylinder valve.
• O-Ring [FR-540G, viton or equivalent]: Ensures adequate
seal between the cylinder valve and the conserver to prevent
oxygen leaks.
O-Ring
Cylinder
Alignment
Nut
Connector
Handwheel
• Cylinder Alignment Nut and Handwheel: These are
used to attach the unit to any CGA 540 cylinder.
• Oxygen Supply Outlet: Use this fitting to attach a
standard cannula.
• Oxygen Pressure Gauge: Enables the user to monitor
the contents of the compressed oxygen cylinder and is
protected by a rubber guard. (Does not apply to Model
511WG.)
• Selector Switch: Enables the user to select the
desired setting, as well as “OFF” and "CF" (continuous
flow). When not in use, the switch should be turned to
the "OFF” position.
Oxygen
Pressure
Gauge
With
Rubber
Guard
Oxygen
Supply
Outlet
Selector
Switch
Vent
Hole
FIGURE B
CYPRESS OXYPneumatic Conserver
with CGA 540 Connection
(Model 523 shown here)
• Vent Hole: Maintains proper internal pressure. Do not obstruct with any object, such as a
label or tight-fitting carrying bag.
WARNING: Use only a manufacturer specified gasket.
7
DESCRIPTION OF PART & CONTROLS
FIGURE C-1
Connection View of the
CYPRESS OXYPneumatic Conserver
with CGA 870 Connection
(Model 511 shown here)
*
FIGURE C-2
Connection View of the
CYPRESS OXYPneumatic Conserver
with CGA 540 Connection
(Model 523 shown here)
NOTE: The continuous flow setting (CF) is designed for emergency use only. The
amount of oxygen delivered when using the CYPRESS conserver in continuous flow mode
is preset to 2 lpm (liters per minute). Remember that in this mode the oxygen will be
consumed at a much faster rate. Return to another source before running out of oxygen.
8
ASSEMBLY AND USE
• Make certain that your hands are free of oil, grease, and other contaminants.
• Inspect the unit to ensure that it has the appropriate viton (or equivalent)
gasket, in good working condition, attached to the inlet nozzle.
• Secure the cylinder in an upright position.
• Inspect the valve of the cylinder and the CYPRESS conserver to ensure they
are free of contaminants. If any indication of damage or contamination is
detected, DO NOT use the equipment and contact your Home Care Provider.
WARNING: Use ONLY a manufacturer specified gasket. An incorrect gasket may
not be oxygen compatible or may cause an oxygen leak, creating an increased fire
risk.
NON-PORTABLE USE:
The CYPRESS conserver is designed to extend the life of portable oxygen supplies when
away from the primary source. While the CYPRESS conserver may be used with
stationary oxygen sources, the unit should be used only while awake and reasonably
attentive. The CYPRESS conserver is not intended for use while asleep because, in the
unlikely event of operational malfunction or dislodging of the cannula, the user could be
unaware and not make the necessary corrections.
9
ASSEMBLY AND USE
INSTALLING THE SYSTEM (CGA 870 Models):
STEP 1: Loosen the cylinder adjustment knob.
STEP 2: Lower the CYPRESS conserver over any
post valve cylinder with the alignment
pins toward the holes on the cylinder
neck [see Fig. D].
STEP 3: Line the two pins and gasket with the
corresponding holes on the cylinder post
valve.
*
NOTE: Cylinder adjustment knob
should be aligned with indentation on post
valve.
FIGURE D
Attaching the CYPRESS OXYPneumatic Conserver to the Cylinder
STEP 4: While holding the unit in place, tighten the cylinder adjustment knob by
turning clockwise [see Fig. D].
STEP 5: Attach a standard cannula (7 ft. or less in length) to the oxygen supply outlet.
*
NOTE: Tighten only by hand. The use of a tool to tighten the knob may
damage the unit.
10
ASSEMBLY AND USE
INSTALLING THE SYSTEM (CGA 540 Model):
STEP 1: Secure the cylinder in an upright position.
STEP 2: Slide the coupling nut/handwheel on the unit toward the
pressure gauge so that the end of the connector is visible.
STEP 3: Insert the connector into the valve outlet on the cylinder.
STEP 4: Slide the coupling nut/handwheel toward the treads on the
valve.
STEP 5: Tighten the union nut/handwheel by turning it clockwise.
STEP 6: Attach a standard cannula (7 ft. long or less) to the oxygen
supply outlet.
*
NOTE: Tighten only by hand.
FIGURE E
Attaching the
CYPRESS
OXYPneumatic
Model 523
Conserver
to the Cylinder
11
ASSEMBLY AND USE
OPERATING INSTRUCTIONS:
STEP 1: Make sure that the CYPRESS conserver is set to the “OFF” position
before opening the cylinder valve.
STEP 2: To reduce the risk of rapid oxygen recompression and fire, open the
cylinder valve slowly and completely so the pressure gauge moves
slowly as it indicates the cylinder pressure.
STEP 3: Listen for leaks. If a leak is present, close the cylinder valve, check
the CGA seal, and reinstall. If the leak persists, DO NOT USE THE
FIGURE F
EQUIPMENT. Contact your Home Care Provider for repair.
View of the CYPRESS
STEP 4: Check the CYPRESS oxygen pressure gauge to verify the cylinder
selector switch
pressure.
STEP 5: Select the setting on the CYPRESS conserver to the appropriate delivery setting [See Fig. F].
STEP 6: Ensure that the vent hole [see Figs. A & B, pg. 6] on the side of the unit is not obstructed.
STEP 7: As with any nasal cannula, place the nasal cannula into position with the prongs in the
nostrils and begin breathing.
The CYPRESS conserver will now start to deliver oxygen. The amount of oxygen delivered per
pulse is determined by the setting. A sound may be heard each time the unit delivers a pulse of
oxygen. Adequate oxygenization will be achieved because of the precise time in the breathing cycle
in which the pulse of oxygen is delivered.
*
NOTE: To help prevent possible damage to the unit and to maintain its cleanliness, keep the
CYPRESS conserver in a carrying bag designed for use with your CYPRESS model.
12
STEP 8: When finished using the system, close the oxygen supply cylinder
valve and continue breathing through the nasal cannula until no
further oxygen is detected.
STEP 9: Remove the nasal cannula and turn the selector switch to the
"O" (off) position.
STEP 10: When not in use, store in a clean, dry location.
FIGURE G
Carrying Bags
OXYGEN CYLINDER DURATION
Because the total delivery of oxygen via the CYPRESS conserver is related to the breathing rates, it is
user adaptive in that the total oxygen delivered per minute will automatically adjust with user need, as
expressed by increased or decreased breathing rates. For example, at all settings, twice as much oxygen
per minute will be delivered if one breathes twenty (20) times per minute as compared with ten (10) times
per minute. Tables 1 and 2 below can be used as a guide.
TABLE 1
CYPRESS
Models 511,
511WG, 523
Cylinder Type
M2
M4(A)
M6(B)
M9(C)
D
E
TABLE 2
CYPRESS
Model 512
Cylinder Type
M2
M4(A)
M6(B)
M9(C)
D
E
SETTING
Delivery Volume (ml)
Cylinder Volume
Liters @ 2015 psi
36
113
164
246
425
680
SETTING
Delivery Volume (ml)
Cylinder Volume
Liters @ 2015 psi
36
113
164
246
425
680
1
16
2
32
3
48
4
64
5
80
6
96
1.9
5.9
8.5
12.8
22.1
35.4
Estimated Cylinder Duration in Hours
(Based on 20 breaths/min)
0.9
0.6
0.5
0.4
0.3
2.9
2.0
1.5
1.2
1.0
4.3
2.8
2.1
1.7
1.4
6.4
4.3
3.2
2.6
2.1
11.1
7.4
5.5
4.4
3.7
17.7
11.8
8.9
7.1
5.9
1
16
1.5
24
1.9
5.9
8.5
12.8
22.1
35.4
Estimated Cylinder Duration in Hours
(Based on 20 breaths/min)
1.3
0.9
0.8
0.6
0.5
3.9
2.9
2.4
2.0
1.5
5.7
4.3
3.4
2.8
2.1
8.5
6.4
5.1
4.3
3.2
14.8
11.1
8.9
7.4
5.5
23.6
17.7
14.2
11.8
8.9
2
32
2.5
40
3
48
4
64
Continuous
2 lpm
0.3
0.9
1.3
2.1
3.5
5.7
Continuous
2 lpm
0.3
0.9
1.3
2.1
3.5
5.7
13
CARE AND MAINTENANCE
The CYPRESS conserver is designed for a long and accurate life; however, as with any
pneumatic device, normal prudent care is required. The unit should be kept clean and free
from moisture and dust, as well as extreme temperature. Do not expose the unit to water,
such as when bathing or swimming. It is advisable to keep the system in its carrying bag
to afford a degree of protection. Clean the outside of the unit periodically with a clean, lintfree cloth. Pay special attention to the oxygen inlet and outlet to make sure they remain
free of dust, etc. If the oxygen inlet connection becomes contaminated with dirt, oil, or
grease, DO NOT USE OR ATTEMPT TO CLEAN. Contact your supplier for service or
repair.
Cannula tubing is a disposable accessory that should be replaced periodically following
normal usage. Disposable tubing should be disposed of in accordance with local
ordinances and/or regulations for disposal. Replacements are available through your
Home Care Provider.
Clean the carrying bag using mild detergent, cold water, and a small scrub brush. Wet the
brush and lightly scrub the bag. Be careful not to scrub the plastic window. When finished
cleaning, rinse with fresh, cold water. Repeat cleaning, if necessary. Hang the bag in a
well ventilated area and allow to air dry. Do not hang in direct sunlight.
14
TROUBLESHOOTING
PROBLEM
Unit does not
pulse.
Unit pulses or flows
continuously.
PROBABLE CAUSE
SOLUTION
Cylinder valve is closed.
Turn the cylinder valve to the
“ON” position.
Cylinder is empty.
Check the oxygen gauge.
Replace the cylinder, if empty.
Oxygen cannula is blocked or
kinked.
Remove kinks. Clean or
replace, if necessary.
Selector switch is set to the
“OFF” position.
Make sure the selector switch
is set to the appropriate setting.
Unit is set to the “CF”
position.
Turn the selector switch to the
appropriate delivery setting.
Unit was not set to “OFF” prior
to opening the cylinder valve.
Turn the selector switch to “OFF,”
wait a few moments, then set at
proper delivery setting.
Vent hole is obstructed.
Remove obstructions, such as labels
or tight-fitting carrying bag, and
resume use as usual.
Non-functioning units are subject to warranty provisions and the manufacturer repair/return policy.
If necessary, call your Home Care Provider.
*
NOTE: Do not attempt to open the unit. If the unit is opened or tampered with, the warranty is void.
15
CLASSIFICATIONS
The CYPRESS OXYPneumatic conserver is classified as:
• Not suitable for use in the presence of flammable anesthetic mixture
with air, oxygen, or nitrous oxide.
16
SPECIFICATIONS
Oxygen Delivery:
[Refer to Tables 1 & 2
pg 13]
Pressure:
Regulator:
Dimensions:
Weight:
Operating Temperature:
Operating Relative Humidity:
Operating Altitude:
Storage/Transportation:
Shock:
Vibration:
MODEL 511/511WG/523
MODEL 512
SWITCH POSITION DELIVERY
SWITCH POSITION DELIVERY
O
OFF
0
OFF
1
16 ml
1
16 ml
2
32 ml
1.5
24 ml
3
48 ml
2
32 ml
4
64 ml
2.5
40 ml
5
80 ml
3
48 ml
6
96 ml
4
64 ml
CF
2.0 ± .5 lpm continuous
CF
2.0 ± .5 lpm
200 psi to 3000 psi
(1.4 MPa to 20.7 MPa )
Built-in, 25 ± 5 psi – Brass high pressure with aluminum low pressure materials
(170 kPa ± 35 kPa)
Models 511, 511WG and 512 - Approximately 5 in. L (13 cm) x 2.5 in. D (6.3 cm)
Model 523 - Approximately 4.3 in L (11 cm) x 3 in. D ( 7.6 cm)
Models 511, 511WG and 512 - Approximately 15 ounces (425 grams)
Model 523 - Approximately 19 ounces (540 grams)
32ºF to 122ºF (0ºC to 50ºC)
15% to 95%
0 to 10,000 feet (0 to 3,048 meters)
Minimum -40ºF (-40ºC), 1% RH
Maximum 145ºF (63ºC), 44% RH
Not to exceed IEC 68-2-27 requirements
Not to exceed IEC 68-2-6, IEC 68-2-34
SYMBOLS KEY:
No smoking or open flames
Consult accompanying documents
17
LIMITED WARRANTY
The CYPRESS OXYPneumatic oxygen conserver has been carefully manufactured and
inspected and is warranted to be free from defects in workmanship and materials. Under
this warranty, CHAD Therapeutics’ obligation shall be limited to the replacement or repair
of any such units or parts that prove, by CHAD’s inspection, to be defective within two
years from the date of purchase. Any abuse, operation other than the intended use of the
product, negligence, accident or repair by other than authorized service professionals shall
immediately void this warranty. This warranty does not extend to the cannula.
CHAD Therapeutics will not accept damages or charges for labor, parts or expenses
incurred in making field repairs, except upon written authorization prior to such action.
The foregoing warranty is exclusive and in lieu of all other express warranties. Implied
warranties, if any, including but not limited to the implied warranties of merchantability and
fitness for a particular purpose, shall not extend beyond the duration of the express
warranty provided herein. In no event shall CHAD Therapeutics be liable for loss of use or
profit or other collateral, special or consequential damages.
18
IMPORTANT INFORMATION TO RECORD
Your Name: ______________________________________________________________
Date you received your unit: _________________________________________________
Prescribed oxygen flow setting:
• At rest:
___________________________
• During exercise: ___________________________
Home Care Provider’s Name:_________________________________________________
Home Care Provider’s Phone Number: (________)________________________________
Physician’s Name:__________________________________________________________
Physician’s Phone Number:(_______)__________________________________________
Notes:___________________________________________________________________
________________________________________________________________________
________________________________________________________________________
19
NOTES
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
20
CHAD, OXYMATIC, TOTAL O2, and OXYPneumatic are
registered trademarks of CHAD Therapeutics, Inc.
This manual is copyrighted by CHAD Therapeutics, Inc.
and may not be copied or otherwise reproduced.
CHAD Therapeutics, Inc. retains all rights not expressly
granted. Copyright infringement may also be subject to
civil liability.
©2005 CHAD Therapeutics, Inc.
21622 Plummer Street • Chatsworth, CA 91311 • USA
1-800-423-8870 • 818-882-0883 • Fax: 818-882-1809
www.chadtherapeutics.com
Authorized Representative:
MDSS
Burckhardtstrasse 1
30163 Hannover, Germany
United States Patent Number 6,484,721
PM-00004/05/B • Printed in the U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement