11&1 ~ AIiIW - Scale Manuals

11&1 ~ AIiIW - Scale Manuals
This Document is Hosted by: www.oldwillknottscales.com
USER MANUAL
The 15R<-200 require both 100g & 200gram weights to calibrate.
1) Place the scale on aflat, very stable surface and turn it ON until the LCD displays 110.00':
2) Press and hold the 1M] key for 5seconds until the display shows "CAL~"then release the key.
3) Press the 1M] key again, the display will ftash "100.00g".
4) Gently place a100g weight on the platform ofthe scale, wait 3 seconds, the display will ftash"200.l
5) Remove the 100g weight from the piatform, gently place a200g weight on the scale, wait 3 se«
display will show"PASS".
6) The scale goes backto weighing mode. Calibration is complete. Remove the weight and turn the SCi
NOTE: if after calibration your scale does not read accurately, this indicates calibration error and the ca
process should be repeated slower. Please calibrate on avery stable flat surface.
INACCURACY / ERROR
The primary reason for inaccuracy or malfunction are low batteries, incorrect calibration, overload or 0
on an unstable surface. Please keep this in mind and maintain and operate your scale properly. The'
precise instrument and must be handled with the utmost care and caution.
ISIIIII
ENGLI5H Jf:lIi
iJl\'I!
FEATURE
Thank you for purchasing the J-Scale" JSR< digital scale. Please read all operating instructions carefully
before use. This electronic scale is aprecision instrument. With normai care and proper treatment, it will
provide yea~ of reliable service.
Power Up SegmentTest
When first turning the unit on, all segments ofthe display will appear as shown below. This display wi
for approXimately 2seconds and then reset to "0, - HI-"
For further information or troubleshooting, please visit our website at www.jscale.com
OVERLOAD
When an applied load exceeds the capacity. "0_ Ld" will appear on the display. Remove the exces'
immediately! Although the JSR* uses proprietary overload protection technology, it is still possible to
the weighing sensors by overload. REMEMBER: You can permanently damage the scale by overloading
FEATURES & SPECIFICATIONS
•
._---.--_ .....
•
_.---~~~~~~
•
'O.ldwt. "'.
·:9.6A~wt
Weighmeter""
On the side of the display you will notice aseries of bars that increase as the load on the scale increaSl
our Weighrneter'" invention. It helps you know the remaining capacity on the scale and also will in(
overload if one occurs. Please use the Weighmeter™ to monitor your weighing loads and please do not
this scale.
TROUBLESHOOT~N~._&_0..P.I:.~!,:::T.:.:IO:.:N=NO::..T.:.:E=S,-
.;
1) If the display ever become, locked on "8888: "LLLL" or "EEEE'; this Indicates that the scale was
dropped or otherwise dal)laged and the delicate weighing sensors may have been damaged, PI
recalibrating the scale O(thesensor has not been hurt too badly- it will work again after recali
Otherwise you will have to follow the warranty instructions that came with your scale.
11&1 ~ AIiIW
,:O;go~9Z",',,>?~54oi ::. _.!
O.lgn
'!iilWEIGHMETER
:=
TECHNOLOGY
r ...,,1 7,"',J""
Adtllli""ol
USJCAI~U
p"o",,",_.<1~,",""'"~
3086Agn
2) If the display shows"- Lo'; this often indicates low batteries. However sometimes it also may ir
serious zero mark error. This means when you turn the scale on, it can'tdetermine what zero is (a sli
mark error will cause situation #1 above). Thus, if new batteries do notnx this error the scale will have tl
to us for replacement under our 20 years warranty program.
:p;6_5:~~:ii:~;-·:;:';to§~~t_F'
O.OOlozt
_
4.823ozt
:; g.ij.1.aWt';:E<:·:~~_:[email protected],'
~,~-~
~void lengthy exposure to extreme heat or cold, your scale works
best when operated at normal room temperature. If the scale has been subjected to temperature change, please allow the scale to acclimate to normal room
Although the JSR~ is designed to be extremely durable. It's important that you never overload or drop/s
scale. Scales are delicate instruments and unlike Cellular phones,scales have delicate sensors that dl
how much an item weighs. If you drop or shock your scale, these sensors "feel" the shock and are so
destroyed, This happens with all digital scales. We design our scales to be as resistant to shock or
possible. However there is no way for us to protect 100% against load cell or sensor damage. Awei
scale will proVide years of reliable and accurate weighing. However an abused scale will only work
sensors are damaged.
temperature for at least one hour before use. Allow sufficient warm up time, Turn the scale On and wait several
seconds to give the internal components achance to stabilize before weighing. The cleaner the enYitonmentthe
better. Dust, dirt, moisture, vibration, air currents and proXimity to other electronic eqUipment can all cause an
~dverse effect on the reliability and accuracy of your scale. Handle with care. Gently apply all items ,to be
weighed onto tray top. Although this scale is designed to be qUite durable, try to avoid rough treatment as this
may permanently damage the internal sensor and void your warranty. Avoid shaking; dropping or otherwise
;hocking the scale. This is aprecision instrument and MUST BE HANDLED WITH EXTREME CARE.
KEY PAD FUNCTIONS
---------. __:.:..:..::.:-=----------------.. ~_.._---...._-_...
1M]
IMPORTANT ADVICE: Place the item to be weighed on the platform, after the stable weight is displayed remove
the itel!1 immediately. This will prolong the longevity and accuracy ofthis weighing instrument.
Mode selection. Press and release the key once to change weight unit You can select g{.grams}, oz {ounl
(pennyweight), ozt (troy ounces), ct (carats) or gn (grains).
fhese electronic scales are precision instruments. Do not operate near an in-use cell phone, cordless phone,
radio, computer or other electronic device. These devices emit RF and can cause unstable scale readings. If your
)cale ever performs poorly, try moving the scale to adifferent room or location. This is avery precise scale - the
display may seem to wander or jump when weighing. This is due to air currents or vibrations. Stable weighing
is achieved when the display remains fixed for 3seconds.
[.~]
Part counting mode. Sample sizes can be 25, 50, 75 or 100. The follOWing steps outline the proCE
cummulative weighing ofsamples:'switch the scale on, Place a'given' number ofsamples of an item on
Press and hold the IPCS] key until the displayftash the number in PCS (the Indicator should be on pes). I
key to select the sample size (the same as you chose above), in the end press the [PCS] key, Then after 2
the scale will remember the sample size you selected and show the starting sample size on the display.
now remove the samples if yOll want to return the scale to 0pcs). Place the items that you want coun
the tray, the total number of items will show on the display. Press the [M] key to exit the counting func
return to normal weighing mode.
OPERATION
------_._----.- -- .. ----------~~~~SATTERY OPERATION
1} Two"AAA"size ALKALINE batteries are required,
2) To install batteries: Release the battery cover by sliding out-wards. - Place batteries into battery compartment aligned correctly. - Replace battery cover. DO NOT USE EXCESSIVE FORCE & DO NOT PRESS ONTHETRAY!!!
~) The scale is now ready for battery operation.
CALIBRATION (Advanced users only)
IMPORTANT: This scale was professionally factory calibrated before shipment and does NOT need to be
recalibrated by the end user. However, if you wish to reca!ibrate your scale we proVide these instructions for
:alibration: Repeat calibration ifthe display locks on 8888, EEEE or LLLL.lncorrect calibration can occur if you do
not follow the steps exactly.Jfyour scale does not perform accurately, please try replacing your batteries before
fOU calibrate. You will need a calibration weight (see below) to calibrate this scale.
t40TE: ifyou do not have access to acalibration weight you can purchase one at your local store or in emergency
)jtuations you can use coins or weights (Ie 20US Nickels = 100g, 200US Nickels = 1000g) as acalibration weight.
The JSR'3l-100~ JSR3 -150 require a 100gram weight to calibrate, The JSRf:l·600 require a 500gram
weight to calibrate.
. .. ,
1) Place the scale on aflat, very stable surface and turn it ON until the LCD displays"0.0" or"O.OO",
2) Press and hold the 1M] key for 5seconds until the display shows"CAL-"then release the key.
l) Press the 1M] key again, the display will ftash "100.00g" (or"500.0g").
I) Gently place the weight(s) on the scale and walt 3seconds. The display will show"PASS~·
5) The scale aoes back to weiahina mode. calibration is comolete. Remove the weiaht and turn the scale OFF.
1
I<!>]
On/Off. Press this key to turn the scale on. When the scale is on, press and hold the same key to turn th
IT]
Tare. Press [T] to resetthe scale to zero, This can be used for eliminating from asample (or aTray/Conta
weight value of a container weight is permanently removed for the remainder of the procedure. Just
scale ON, place the tray or container on weighing platform, and press the [T] key, the scale will sho\
0.00) on the display and you can add items to the container/tray. NOTE: When all weight are removed
weighing tray, the tared val,ue of a container will be displayed as a negative number. Cycle the pOWE
scale to reset the scale to zero.
i
[LIGHT]
Press the center [Light] key to turn on the bright LCD backlight. It will stay on for several seconds. Pres~
again to turn offthe backlight.
WII\/I/V
ic;rrllp rnm
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement