User`s Manual
PRO AUDIO
SERIES
PR
0202020!
130-Watt 8-channel PA System with Two 10-inch
Speakers
USER'S MANUAL
PRO AUDIO
SERIES 8-Channel PA System with 2x10” Speakers = USER’S MANUAL
Safety Precautions
These speakers are not designed to be suspended from a ceiling (also known as "flying").
Never fly these speakers.
Installation of these speakers must be carried out by qualified personnel following the
approved safety standards.
Do not attempt to clean the plastic enclosure with solvents or petrochemical based cleaners.
Do not place heat sources, such as lighting equipment or smoke machines, on the speaker or
amplifier.
Do not expose the speakers or amplifier to direct rain or standing in water.
Liquid getting into the box will risk a short circuit and will be hazardous.
Do not stack the speakers in a manner that could cause injury should a cabinet become
dislodged.
Ensure that the amplifier is disconnected from the AC power source before making any
electrical or signal connections.
Disconnect from main power before to make connections in the amplifier.
Make sure that the power cord is never crimped or damaged by sharp edges. Never let the
power cord come into contact with other cables. Never pull on the cord to remove it from the
power outlet. Always grasp the connector head when removing the plug from a power outlet.
Before connecting or operating your new loudspeaker, please study the accompanying
instruction manual, paying special attention to the operating precautions and wiring
procedures.
PRO AUDIO
Me:
8-Channel PA System with 2x10” Speakers = USER’S MANUAL
Rear Panel
о о
o
MM PRO AUDIO
SERIES
5 5 5
4 io 4 5 5 ois
7 | 3 7 | 2
=8 | 2" 8 |2 8
1 * | 1 “о ° 9
+ . + .
о 10 о 10 0 о
Trams
5 5 5
415 4 5 6 1.6
т | 3.
АБЫ А
ons WARNING: SHOCK HAZARD-DO NOT OPEN
AIS: RISQUE DE CHOC ELECTRIQUENE PAS OUVRIR.
Powered Mixer
Frequency Response: 20 Hz - 20 kHz
THD:< 1%
Output Power (RMS): 2x 65watts
Output Power (Peak): 2x 13Owatts
Channel EQ: Treble: 10 kHz +6dB
Bass: 100 Hz +6dB
Input Power: 95 ~ 250 VAC, 50/60 Hz
Mixer:
Speaker: Low Drivers: 1x 10" cone (each)
High Drivers: 1x 1" compression driver (each)
Maximum Input Power: 100 watts at 8 ohms
Frequency Response: 60 Hz ~ 18 kHz
Sensitivity: 94dB
Weight: 46.3 Ibs. (21 kg)
1. Speaker Outputs
2. Stereo in 5/6
3. Monitor Outputs
4. Volume
5. Stereo in 7/8
6. Phantom Power Indicator
7. Phantom Power Switch
8. Monitor Outputs Volume
9. Headphone Output
10. Clip Indicator
11. Echo Master
12. Volume Master
13. Power Indicator
14. Channel Clip Indicator
15. Microphone Input
16. Line Input
17. Treble
18. Bass
19. Echo
20. Volume
PRO AUDIO
SERIES 8-Channel PA System with 2x10” Speakers = USER’S MANUAL
1. Speaker Outputs: Connect the speakers using the provided speaker cables.
2. Stereo In 5/6: 2x RCA or 1/4" unbalanced inputs. Connect your line-level device,
such as a CD player, drum machine, or tape deck here.
3. Monitor Outputs: These are unpowered RCA and 1/4" unbalanced outputs.
4. Volume: This knob controls the volume level of inputs 5/6 and 7/8.
5. Stereo In 7/8: This is a 3.5mm TRS unbalanced stereo input for connection to any
line-level device.
6. Phantom Power Indicator: This LED illuminates when Phantom Power is
engaged.
7. Phantom Power Button: Depress this button to engage Phantom Power.
Phantom Power puts +48V on all 4 XLR connectors. Do not connect any microphones or
devices that do not require Phantom Power when Phantom Power is engaged.
8. Monitor Outputs Volume: Controls the volume level of both the Monitor and
Headphones outputs.
9. Headphone Output: Connect a pair of headphones to this stereo 3.5mm TRS
jack.
10. Clip Indicator: This LED indicates when the signal is being clipped.
11. Echo Master: This knob controls the amount of echo that is sent to the main mix.
12. Volume Master: This knob controls the overall volume level for the entire amplifier.
13. Power Indicator: This LED is illuminated when the mixer is powered ON.
14. Channel Clip Indicators: These LEDs (one for each of the first four channels)
will light up when the input signal is clipping or near clipping. Reduce the input level to elimi-
nate the distortion caused by clipping.
PRO AUDIO
SERIES 8-Channel PA System with 2x10” Speakers = USER’S MANUAL
15. Microphone Input: Connect a condenser or dynamic microphone to this 3-pin
balanced XLR jack. Do not use both condenser and dynamic mics at the same time. Con-
denser mics require phantom power and phantom power can damage dynamic mics.
16. Line Input: Connect a line level device, such as a tape deck, CD player, or drum
machine, here.
17. Treble: Use this knob to adjust the treble (high) frequencies.
18. Bass: Use this knob to adjust the bass (low) frequencies.
19. Echo: Use this knob to control the portion of the signal that will go to the echo effect
section.
20. Volume: Use this knob to control the volume level of the channel.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement