null  User manual
PanelView Plus
Terminals
2711P
(400, 600, 700, 1000, 1250, 1500)
User Manual
Important User Information
Solid state equipment has operational characteristics differing from those of
electromechanical equipment. Safety Guidelines for the Application,
Installation and Maintenance of Solid State Controls (Publication SGI-1.1
available from your local Rockwell Automation sales office or online at
http://www.ab.com/manuals/gi) describes some important differences
between solid state equipment and hard-wired electromechanical devices.
Because of this difference, and also because of the wide variety of uses for
solid state equipment, all persons responsible for applying this equipment
must satisfy themselves that each intended application of this equipment is
acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for
indirect or consequential damages resulting from the use or application of
this equipment.
The examples and diagrams in this manual are included solely for illustrative
purposes. Because of the many variables and requirements associated with
any particular installation, Rockwell Automation, Inc. cannot assume
responsibility or liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to
use of information, circuits, equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without
written permission of Rockwell Automation, Inc. is prohibited.
Throughout this manual, when necessary we use notes to make you aware of
safety considerations.
WARNING
IMPORTANT
ATTENTION
Identifies information about practices or circumstances
that can cause an explosion in a hazardous environment,
which may lead to personal injury or death, property
damage, or economic loss.
Identifies information that is critical for successful
application and understanding of the product.
Identifies information about practices or circumstances
that can lead to personal injury or death, property
damage, or economic loss. Attentions help you:
• identify a hazard
• avoid a hazard
• recognize the consequence
SHOCK HAZARD
Labels may be located on or inside the equipment (e.g.,
drive or motor) to alert people that dangerous voltage may
be present.
BURN HAZARD
Labels may be located on or inside the equipment (e.g.,
drive or motor) to alert people that surfaces may be
dangerous temperatures.
Table of Contents
Preface
Objectives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Contents . . . . . . . . . . . . . . . . . . . . . . . . . .
Intended Audience . . . . . . . . . . . . . . . . . . . . . . . .
Related Publications . . . . . . . . . . . . . . . . . . . . . . .
European Communities (EC) Directive Compliance
Rockwell Automation Support . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
Preface-i
Preface-i
Preface-ii
Preface-ii
Preface-iii
Preface-iii
Preface-iv
Chapter 1
Overview
Chapter Objectives . . . . . . . . . . . . . .
Software Support . . . . . . . . . . . . . . .
PanelView Plus 400 - 600 Features. . .
PanelView Plus 700 - 1500 Features . .
Catalog Number Configuration. . . . . .
PanelView Plus Product Components.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1-1
1-1
1-2
1-7
1-12
1-12
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
2-1
2-1
2-3
2-3
2-4
2-4
2-5
2-5
2-6
2-12
2-14
Chapter Objectives . . . . . . . . . . . . . . . . . . . . .
Wiring and Safety Guidelines. . . . . . . . . . . . . .
Installing and Removing Power Terminal Block
Connecting DC Power. . . . . . . . . . . . . . . . . . .
Connecting AC Power . . . . . . . . . . . . . . . . . . .
Resetting the Terminal. . . . . . . . . . . . . . . . . . .
Startup Sequence . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3-1
3-1
3-2
3-3
3-5
3-6
3-8
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
4-1
4-1
4-4
4-5
4-5
4-5
Chapter 2
Installation
Chapter Objectives . . . . . . . . .
Hazardous Locations . . . . . . . .
Environmental Considerations .
Enclosures . . . . . . . . . . . . . . .
Clearances . . . . . . . . . . . . . . .
Outdoor Installation . . . . . . . .
Required Tools . . . . . . . . . . . .
Cutout Dimensions . . . . . . . . .
Mounting Dimensions . . . . . . .
400 - 600 Panel Installation . . .
700 - 1500 Panel Installation . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Chapter 3
Applying Power
Chapter 4
Using Configuration Mode
i
Chapter Objectives . . . . . . .
Starting Configuration Mode
Loading an ME Application .
Running an Application. . . .
Application Settings. . . . . . .
Terminal Settings . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Publication 2711P-UM001C-EN-P
Table of Contents
ii
Networks and Communications .
Diagnostic Setup . . . . . . . . . . . .
File Management. . . . . . . . . . . .
Display . . . . . . . . . . . . . . . . . . .
Font Linking . . . . . . . . . . . . . . .
Input Devices . . . . . . . . . . . . . .
Print Setup . . . . . . . . . . . . . . . .
Startup Options. . . . . . . . . . . . .
System Event Log . . . . . . . . . . .
System Information . . . . . . . . . .
Time/Date/Regional Settings . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
4-6
4-15
4-16
4-19
4-21
4-22
4-26
4-28
4-32
4-33
4-36
Chapter Objectives . . . . . . . . . . . . . . . . . . . . .
Required Tools . . . . . . . . . . . . . . . . . . . . . . . .
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compatibility of Terminal Components . . . . . .
Installing RAM and Internal Compact Flash . . .
Installing and Replacing the Logic Module . . . .
Installing/Replacing a Communication Module .
Replacing the Display Module . . . . . . . . . . . . .
Replacing the Battery . . . . . . . . . . . . . . . . . . .
Replacing Bezel . . . . . . . . . . . . . . . . . . . . . . .
Replacing Backlight. . . . . . . . . . . . . . . . . . . . .
Installing the Remote AC Power Supply . . . . . .
Removing the Product ID Label . . . . . . . . . . . .
Installing Keypad Legend Inserts . . . . . . . . . . .
Using an External Compact Flash Card. . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
5-1
5-1
5-1
5-2
5-3
5-4
5-6
5-10
5-12
5-14
5-16
5-19
5-19
5-20
5-21
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
6-1
6-1
6-2
6-5
6-6
6-9
6-11
6-16
Chapter 5
Installing and Replacing
Components
Chapter 6
Terminal Connections
Publication 2711P-UM001C-EN-P
Chapter Objectives . . . . . . . . . . . .
Wiring and Safety Guidelines. . . . .
Logic Controller Cable Charts . . . .
USB Ports . . . . . . . . . . . . . . . . . . .
Serial Connections. . . . . . . . . . . . .
Ethernet Connections . . . . . . . . . .
DH-485/DH+/Remote I/O Module .
ControlNet Module . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Table of Contents
iii
Chapter 7
Transferring files and Upgrading
Firmware
Chapter Objectives . . . . . . . . . . . . . . . . . . . . .
Transferring Files Using a Compact Flash Card .
Transferring Files from a Computer . . . . . . . . .
Upgrading Firmware . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
7-1
7-1
7-1
7-1
Chapter 8
Troubleshooting and Maintenance Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
LED Indicators . . . . . . . . . . . .
General Troubleshooting. . . . .
Troubleshooting Components .
Ethernet Problems. . . . . . . . . .
Advanced Troubleshooting . . .
Startup Error Messages . . . . . .
Startup Status Messages . . . . . .
System Identification Errors . . .
Startup Problems. . . . . . . . . . .
Entering Configuration Mode. .
Restarting in Safe Mode . . . . . .
Cleaning the Display Window .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
8-1
8-2
8-4
8-8
8-9
8-10
8-11
8-12
8-13
8-13
8-13
8-14
Appendix A - Specifications
Appendix B - Compatible USB Devices
Appendix C - Available Fonts for Terminal Applications
Index
Publication 2711P-UM001C-EN-P
Table of Contents
iv
Publication 2711P-UM001C-EN-P
Preface
Objectives
This preface provides information on the contents of this manual
including:
• Contents of manual
• Intended audience
• European Union Directive Compliance
• Rockwell Automation Support
Packing List
The following items are shipped with an assembled PanelView™ Plus
terminal:
• DC Power terminal block (AC or DC terminal block for 400-600
terminals)
• RSView Machine Edition Runtime (preloaded)
• Mounting levers for 400 -600 terminals (8)
• Mounting clips for 700 - 1500 terminals (up to 8)
• Installation Instructions
• Panel cutout template
i
Publication 2711P-UM001C-EN-P
Preface
ii
Manual Contents
Chapter
Title
Description
1
Overview
Provides overview of the PanelView
Plus terminals including features and
product components.
2
Installation
Gives Instructions on how to install
the PanelView Plus terminal in a
panel or enclosure.
3
Applying Power
Describes how to apply power and
reset the PanelView Plus terminal.
4
Using Configuration Mode
Shows how to use the PanelView
Plus configuration screens to
load/run applications and configure
terminal settings for the PanelView
Plus terminal.
5
Installing and Replacing
Components
Shows how to install and replace
components of the PanelView Plus
terminal including:
• Logic Module
• RAM/Internal Compact Flash
• Communication Module
• Display Module
• Battery
• Display Module Bezel
• Backlight
• AC Power Supply
• Product Label
• Keypad Legend Inserts
• External Compact Flash Card
Intended Audience
6
Terminal Connections
Describes connections on the base
unit of the PanelView Plus terminal
and the communication modules.
7
Transferring Files and Upgrading Provides information on transferring
Firmware
files using an External Compact Flash
Card and performing firmware
upgrades.
8
Troubleshooting and
Maintenance
Provides assistance on isolating
problems and general maintenance.
No special knowledge is required to understand this manual or
operate the PanelView Plus terminal. However, it is important that you
understand the functions and operations of Machine Edition
applications that will run on the terminal. Consult the application
designer for this information.
Equipment installers must be familiar with standard panel installation
techniques.
Publication 2711P-UM001C-EN-P
Preface
iii
Related Publications
You may want to refer to the following for additional information:
• online help for RSView Studio or RSLinx
• documentation for your logic controller or processor
European Communities (EC)
Directive Compliance
If this product has the CE mark it is approved for installation within
the European Union and EEA regions. It has been designed and tested
to meet the following directives.
EMC Directive
This product is tested to meet the Council Directive 89/336/EC
Electromagnetic Compatibility (EMC) by applying the following
standards, in whole or in part, documented in a technical construction
file:
• EN 50081-2 EMC - Generic Emission Standard, Part 2 - Industrial
Environment
• EN 61000-6-2 EMC - Generic Immunity Standard, Part 2 Industrial Environment
This product is intended for use in an industrial environment.
Low Voltage Directive
This product is tested to meet Council Directive 73/23/EEC Low
Voltage, by applying the safety requirements of EN 61131-2
Programmable Controllers, Part 2 - Equipment Requirements and
Tests. For specific information required by EN 61131-2, see the
appropriate sections in this publication, as well as the Allen-Bradley
publication Industrial Automation Wiring and Grounding Guidelines
For Noise Immunity, publication 1770-4.1.
Open style devices must be provided with environmental and safety
protection by proper mounting in enclosures designed for specific
application conditions. See NEMA Standards publication 250 and IEC
publication 529, as applicable, for explanations of the degrees of
protection provided by different types of enclosure.
Publication 2711P-UM001C-EN-P
Preface
iv
Rockwell Automation
Support
Rockwell Automation provides technical information on the web to assist you
in using our products. At http://support.rockwellautomation.com, you can
find technical manuals, a knowledge base of FAQs, technical and application
notes, sample code and links to software service packs, and a MySupport
feature that you can customize to make the best use of these tools.
For an additional level of technical phone support for installation,
configuration and troubleshooting, we offer TechConnect Support programs.
For more information, contact your local distributor or Rockwell Automation
representative, or visit http://support.rockwellautomation.com.
Installation Assistance
If you experience a problem with a hardware module within the first 24
hours of installation, please review the information that's contained in this
manual. You can also contact a special Customer Support number for initial
help in getting your module up and running:
United States
1.440.646.3223
Monday – Friday, 8am – 5pm EST
Outside United
States
Please contact your local Rockwell Automation representative for any
technical support issues.
New Product Satisfaction Return
Rockwell tests all of our products to ensure that they are fully operational
when shipped from the manufacturing facility. However, if your product is
not functioning and needs to be returned:
United States
Contact your distributor. You must provide a Customer Support case
number (see phone number above to obtain one) to your distributor in
order to complete the return process.
Outside United
States
Please contact your local Rockwell Automation representative for
return procedure.
Software and Firmware Upgrades
To receive software updates (software serial number required) and
firmware upgrades for your terminal:
• call your local Rockwell Automation sales office or distributor
• call Rockwell Software at 1-440-646-7800 or fax 1-440-646-7801
• access www.software.rockwell.com
Publication 2711P-UM001C-EN-P
Chapter
1
Overview
Chapter Objectives
This chapter gives an overview of the PanelView Plus terminal line
including:
• software support
• PanelView Plus 400 - 600 terminal features
• PanelView Plus 700 - 1500 terminal features
• catalog number configuration
• product components
Software Support
RSView Machine Edition runtime is included with all PanelView Plus
terminals. RSView Machine Edition is runtime and terminal
configuration software for the PanelView Plus terminals and does not
require activation.
RSView Studio is used on a personal computer to create applications
that run in the PanelView Plus terminals. This software is purchased
separately.
1
Publication 2711P-UM001C-EN-P
1-2
Overview
PanelView Plus 400 - 600
Features
This section gives an overview of the PanelView Plus 400 and 600
terminals including:
• hardware features
• base configured units
• communication modules
• AC or DC power supply
• displays
Hardware Features
The PanelView Plus 400 and 600 terminals are operator interface
devices. These terminals feature:
• PanelView Plus 400 terminals offer:
– grayscale graphic displays
– keypad input support
• PanelView Plus 600 terminals offer:
– color or grayscale graphic displays
– keypad, touch screen or keypad & touch screen input
• base configured unit with:
– RS-232 Only or
– RS-232, Ethernet and modular communications interface
• communication modules provide add-on capability to base
configured units with modular communications interface
• AC (85…264V ac) or DC (18…32V dc) power input
• Compact Flash Card slot supports Type I Compact Flash Cards
• USB port for attaching mouse, keyboard, printer, bar code
scanner, and other devices
• same panel cutouts as the PanelView Standard 550 terminals
Publication 2711P-UM001C-EN-P
Overview
1-3
Base Configured Units
The base configured unit of the PanelView Plus 400 and 600 terminals
terminal are available in two versions:
• Base unit with RS-232 only and (1) USB port
• Base unit with RS-232, 10/100BaseT Ethernet, (1) USB port and a
network interface for communication module
RS-232 Only
AC or DC Power Input
Compact Flash Slot
Base Configured Unit with:
• RS-232 and USB Port only
USB Port RS-232 Port
RS232, Ethernet and Modular Communications Interface
AC or DC Power Input
Interface for
Communication Module
Compact Flash Slot
Base Configured Unit with:
• RS-232, USB, Ethernet port and network
interface for communication module
USB Port RS-232 Port
Ethernet Port
Publication 2711P-UM001C-EN-P
1-4
Overview
Communication Modules
You can attach a separate communication module to the base
configured unit of the PanelView Plus with a network interface to
increase your communications capability.
• DH-485
• DH+
• Remote I/O (single rack)
• Isolated RS-232
The Communication Module installs easily on the back of the unit.
Communication
Module
AC or DC Power
The base configured unit of the PanelView Plus 400/600 terminals is
available with either AC (85…264V ac) or DC (18…32V dc) power
input providing application flexibility.
Publication 2711P-UM001C-EN-P
Overview
1-5
Displays and Input Options
PanelView Plus 400 and 600 terminals are available with the following
display and operator input options:
• 400 terminals: 3.8 inch grayscale (320 x 240) graphics display
with keypad
• 600 terminals: 5.5 inch color or grayscale (320 x 240) graphics
display with keypad, touch screen, or keypad & touch support
Touch Screen
The PanelView Plus 600 terminals offer an analog resistive touch
screen allowing for flexible touch area configuration.
600 Color or Grayscale Terminals
with Touch Screen
Publication 2711P-UM001C-EN-P
1-6
Overview
Keypad or Keypad & Touch
The keypad versions of the PanelView Plus 400 and 600 terminals are
available with the following options:
• 400 terminals: grayscale display with keypad input only
• 600 terminals: color or grayscale displays with either keypad or
keypad & touch input
The following illustration shows the features of each terminal:
600 Grayscale or Color Terminal
with Keypad or Keypad & Touch Screen
400 Grayscale Terminal
with Keypad
Replaceable
ID Label
Replaceable ID Label
Numeric Keypad
Numeric Keypad
Backspace and
Enter Keys
Tab and Shift Keys
Backspace and Enter Keys
Tab and Shift Keys
Navigation Keys
Navigation Keys
8 Programmable Function Keys
10 Relegendable Programmable Function Keys
Keys
400
600
Description
F1 - F8
F1 - F10
Programmable keys that initiate functions
on terminal display. Replaceable legends
are available for the 600 terminals allowing
for custom function key labels.
ID Label
Allen-Bradley ID label. The ID label is
replaceable allowing for custom product
identification.
Numeric Keypad
0-9, ., -, Backspace, Enter, Left and Right
Tab keys, Shift keys
Navigation Keys
Use the arrow keys for navigation.
Use the Alt+arrow keys to activate home,
end, page up, and page down functions.
Publication 2711P-UM001C-EN-P
Overview
PanelView Plus 700 - 1500
Features
1-7
This section gives an overview of the PanelView Plus 700, 1000, 1250,
1500 terminals including:
• hardware features
• modular components
• base configured unit
• communication modules
• remote AC power supply
• display modules
Hardware Features
The PanelView Plus 700 - 1500 terminals are operator interface
devices that feature:
• graphic color display modules with keypad, touch screen, or
keypad & touch screen support
• analog resistive touch screen
• field replaceable bezels
• modular communications for easy add-on capability
• memory expansion modules for field upgrades to 256 MB RAM
and 512 MB Compact Flash
• Compact Flash Card slot supports Type I Compact Flash Cards
• USB ports provide connections for keyboard/mouse/printer
• Ethernet and serial communications
• same panel cutouts as the PanelView Standard and PanelView
Enhanced terminals
Publication 2711P-UM001C-EN-P
1-8
Overview
Modular Components
The PanelView Plus 700 - 1500 terminals use modular components
allowing for flexible configuration, installation, and upgrades. Items
can be ordered as separate components or factory assembled per your
configuration.
Communication Module
Logic Module
Display Module
Base Configured Unit
The base configured unit of the PanelView Plus terminal consists of:
• Display Module (700, 1000, 1250, 1500) with Keypad, Touch or
Keypad & Touch Input
• Logic Module
The Logic Module contains:
• 24V dc input (18…32V dc)
• SDRAM and Flash memory (various sizes)
• 10/100BaseT Ethernet Port
• Serial RS-232 Port for file transfers, printing and logic controller
communications
• 2 USB Ports for attaching mouse, keyboard or printer
• Compact Flash Card Slot for Type I Compact Flash cards
• Battery-backed real-time clock
DC Input
Logic Module
Display Module
Ethernet Port
USB Ports
Compact Flash Card Slot
Publication 2711P-UM001C-EN-P
Serial Port
Overview
1-9
Communication Modules
You can attach a separate Communication Module to the base
configured unit of the PanelView Plus terminal to increase your
communications capability.
The Communication Modules install easily on top of the Logic
Module on the back of the unit.
Communication Module
Remote AC Power Supply
The Logic Module provides a DC power input. For applications using
AC power, a remote AC to DC power supply is available for DIN Rail
mounting.
Publication 2711P-UM001C-EN-P
1-10
Overview
Display Modules
PanelView Plus 700 - 1500 terminals offer a range of TFT color graphic
displays with either keypad, touch screen, or keypad & touch support.
• 700 (6.5 inch)
• 1000 (10.4 inch)
• 1250 (12.1 inch)
• 1250 High-Bright Touch (12.1)
• 1500 (15 inch)
All of the displays have common features and firmware providing for
easy migration to a larger display. Field replaceable bezels are also
available.
Touch Screen
The following illustration shows a 1000 touch screen display. All of
the touch screen displays are analog resistive and similar except for
size.
Replaceable ID Label
IrDA Port
(if present)
Touch Screen
Publication 2711P-UM001C-EN-P
Overview
1-11
Keypad or Keypad & Touch
The following illustration shows the features of the 1000 keypad or
keypad & touch display. All of the displays are similar except for size
and the number of function keys available.
Replaceable ID Label
IrDA Port
(if present)
Numeric Keypad
Backspace
and Enter Key
Programmable Function Keys
(optional custom legends)
Tab, Shift Keys
Esc, CT, Alt Keys
Navigation Keys
Programmable Function Keys
(optional custom legends)
All of the Kxx and Fxx function keys on the keypad terminals are
programmable.
Feature
Description
Function Keys
700
(F1-F10, K1-K12)
1000
(F1-F16, K1-K16)
1250
(F1-F20, K1-K20)
1500
(F1-F20, K1-K20)
Programmable keys that initiate functions
on terminal display. Replaceable legends
are available for the terminals allowing for
custom function key labels.
Label
Allen-Bradley ID label. The ID label is
replaceable allowing for custom product
identification.
Numeric Keypad
0-9, ., -, Backspace, Enter, Left and Right
tab, Shift, Esc, Ctrl, Alt keys
Navigation Keys
Use the arrow keys to move cursor in lists,
select objects,
Alt+arrow key activates home, end, page
up, page down functions.
Publication 2711P-UM001C-EN-P
1-12
Overview
Catalog Number
Configuration
Input
Type
|
2711P-
The following table shows the catalog number configuration for
PanelView Plus terminals.
Display
Size
Display Type
|
Communications
|
Power
|
|
Memory
Flash/RAM(1)
|
Label
|
K = Keypad
4 = 3.8 inch
C = Color
PanelView Plus 400 and 600 Terminals
A = AC
1= 32 MB/64 MB
Blank =AB Label
T = Touch
6 = 5.5 inch
M=Grayscale
1 = Remote I/O (single rack), ENet, RS-232 & USB
B = AC (DIN Mtb.)(1)
2 = 128MB/128 MB(1)
N = No Label
B = Key & Touch
7 = 6.5 inch
3 = DH-485, ENet, RS-232 & USB
D = DC
3 = 256 MB/256 MB(1)
10 = 10.4 inch
5 = RS-232 & USB
12 = 12.1 inch
8 = DH+, ENet, RS-232 & USB
15 = 15 inch
20 = ENet, RS-232 & USB
PanelView Plus 700 - 1500 Terminals
4 = ENet, RS-232 & (2) USB
6 = DH+, DH-485, RIO, ENet, RS-232 & (2) USB
15 = CNet, ENet, RS-232 & (2) USB
(1)
Applies to PanelView Plus 700-1500 terminals only.
PanelView Plus Product
Components
All of the components listed in this section are available as separate
catalog numbers for field installation or replacement.
Display Modules (700 - 1500 only)
Publication 2711P-UM001C-EN-P
Cat. No.
Description
2711P-RDK7C
700 Keypad Color Display
2711P-RDT7C
700 Touch Color Display
2711P-RDB7C
700 Keypad and Touch Color Display
2711P-RDK10C
1000 Keypad Color Display
2711P-RDT10C
1000 Touch Color Display
2711P-RDB10C
1000 Keypad and Touch Color Display
2711P-RDK12C
1250 Keypad Color Display
2711P-RDT12C
1250 Touch Color Display
2711P-RDT12H
1250 Touch High-Bright Color Display
2711P-RDB12C
1250 Keypad and Touch Color Display
2711P-RDK15C
1500 Keypad Color Display
2711P-RDT15C
1500 Touch Color Display
2711P-RDB15C
1500 Keypad and Touch Color Display
Overview
1-13
Logic Modules (700 - 1500 only)
Cat. No.
Description
2711P-RP
Logic Module without Flash/RAM memory
2711P-RP1
Logic Module with 32 MB Flash/64 MB RAM
2711P-RP2
Logic Module with 128 MB Flash/128 MB RAM
2711P-RP3
Logic Module with 256 MB Flash/256 MB RAM
Communication Modules
Terminal Type
400 - 600
700 - 1500
Cat. No.
Description
2711P-RN1
Single Rack Remote I/O Communication Module
2711P-RN3
DH-485 Communication Module
2711P-RN8
DH+ Communication Module
2711P-RN22C
RS-232 Isolated Communication Module
2711P-RN6
DH+/DH-485/Remote I/O Communication Module
2711P-RN15S
ControlNet Communication Module
Internal Compact Flash Cards (700 - 1500 only)
Cat. No.
Description
2711P-RW1
32 MB Compact Flash with RSView Machine Edition
2711P-RW2
128 MB Compact Flash with RSView Machine Edition
2711P-RW3
256 MB Compact Flash with RSView Machine Edition
RAM Memory (700 - 1500 only)
Cat. No.
Description
2711P-RR64
64 MB SODIMM Memory
2711P-RR128
128 MB SODIMM Memory
2711P-RR256
256 MB SODIMM Memory
Publication 2711P-UM001C-EN-P
1-14
Overview
Compact Flash Cards (Blank)
Cat. No.
Description
2711P-RC1
32 MB Blank Compact Flash Card
2711P-RC2
128 MB Blank Compact Flash Card
2711P-RC3
256 MB Blank Compact Flash Card
2711P-RC4
512 MB Blank Compact Flash Card
2711P-RCH
Compact Flash to PCMCIA Adapter
Legend Kits
Cat. No.
Description
2711P-RFK6
Replacement Legend Strips for 600 Keypad Terminal
2711P-RFK7
Replacement Legend Strips for 700 Keypad Terminal
2711P-RFK10
Replacement Legend Strips for 1000 Keypad Terminal
2711P-RFK12
Replacement Legend Strips for 1250 Keypad Terminal
2711P-RFK15
Replacement Legend Strips for 1500 Keypad Terminal
Backlights (700 - 1500 only)
Cat. No.
Description
2711P-RL7C
Replacement Color Backlight for 700 Displays
2711P-RL10C
Replacement Color Backlight for 1000 Displays
2711P-RL12C
Replacement Color Backlight for 1250 Series A and B Displays
2711P-RL12C2
Replacement Color Backlight for 1250 Series C Displays
Replacement Bezels
Publication 2711P-UM001C-EN-P
Cat. No.
Description
2711P-RBK7
Replacement Bezel for 700 Keypad Terminal
2711P-RTK7
Replacement Bezel for 700 Touch Terminal
2711P-RBB7
Replacement Bezel for 700 Keypad or Keypad/Touch Terminal
2711P-RBK10
Replacement Bezel for 1000 Keypad Terminal
2711P-RTK10
Replacement Bezel for 1000 Touch Terminal
2711P-RBB10
Replacement Bezel for 1000 Keypad or Keypad/Touch Terminal
2711P-RBK12
Replacement Bezel for 1250 Keypad Terminal
2711P-RTK12
Replacement Bezel for 1250 Touch Terminal
2711P-RBB12
Replacement Bezel for 1250 Keypad or Keypad/Touch Terminal
2711P-RBK15
Replacement Bezel for 1500 Keypad Terminal
2711P-RTK15
Replacement Bezel for 1500 Touch Terminal
2711P-RBB15
Replacement Bezel for 1500 Keypad or Keypad/Touch Terminal
Overview
1-15
Protective Antiglare Overlays
Cat. No.
Description
2711P-RGK4
Antiglare Overlay for PanelView Plus 400 Keypad Terminal
2711P-RGK6
Antiglare Overlay for PanelView Plus 600 Keypad or Keypad/Touch Terminal
2711P-RGT6
Antiglare Overlay for PanelView Plus 600 Touch Terminal
2711P-RGK7
Antiglare Overlay for PanelView Plus 700 Keypad or Keypad/Touch Terminal
2711P-RGT7
Antiglare Overlay for PanelView Plus 700 Touch Terminal
2711P-RGK10
Antiglare Overlay for PanelView Plus 1000 Keypad or Keypad/Touch
Terminal
2711P-RGT10
Antiglare Overlay for PanelView Plus 1000 Touch Terminal
2711-RGK12
Antiglare Overlay for PanelView Plus 1250 Keypad or Keypad/Touch
Terminal
2711P-RGT12
Antiglare Overlay for PanelView Plus 1250 Touch and High-Bright Touch
Terminal
2711P-RGK15
Antiglare Overlay for PanelView Plus 1500 Keypad or Keypad/Touch
Terminal
2711P-RGT15
Antiglare Overlay for PanelView Plus 1500 Touch Terminal
Adapter Plates
Cat. No.
Description
2711P-RAK4
Adapts a PanelView Plus 400 Keypad Terminal to a PanelView
Standard 550 Keypad Cutout
2711P-RAK6
Adapts a PanelView Plus 600 Keypad Terminal to a PanelView
Standard 600 Keypad Cutout
2711P-RAK7
Adapts a PanelView Plus 700 Keypad Terminal to a PanelView
Standard 900 Keypad Cutout
2711P-RAT7
Adapts a PanelView Plus 700 Touch Terminal to a PanelView
Standard 900 Touch Cutout
2711P-RAK10
Adapts a PanelView Plus 1000 Keypad Terminal to a PanelView
1000/1000E Keypad Cutout
2711P-RAT10
Adapts a PanelView Plus 1000 Touch Terminal to a PanelView
1000/1000E Touch Cutout
2711P-RAK12E
Adapts a PanelView Plus 1250 (or PV1000/1000E) Keypad
Terminal to a PanelView 1200/1400E Keypad Cutout
2711P-RAT12E2
Adapts a PanelView Plus 1250 (or PV1000/1000E) Touch
Terminal to a PanelView 1200E Touch Cutout
2711P-RAT12E
Adapts a PanelView Plus 1250 (or PV1000/1000E) Touch
Terminal to a PanelView 1400E Touch Cutout
2711P-RAK12S
Adapts a PanelView Plus 1250 (or PV1000/1000E) Keypad
Terminal to a PanelView Standard 1400 Keypad Cutout
2711P-RAT12S
Adapts a PanelView Plus 1250 (or PV1000/1000E) Touch
Terminal to a PanelView Standard 1400 Touch Cutout
2711P-RAK15
Adapts a PanelView Plus 1500 Keypad or Keypad & Touch
Terminal to a PanelView 1200E/1400E Keypad Terminal
2711P-RAT15
Adapts a PanelView Plus 1500 Touch Terminal to a PanelView
1400E Touch Cutout
Publication 2711P-UM001C-EN-P
1-16
Overview
Cables
Cat. No.
Description
2711-NC13
RS-232 Operating/Programming Cable (9-pin D-Shell to 9-pin D-Shell), 5 m
(16.4 ft)
2711-NC14
RS-232 Operating/Programming Cable (9-pin D-Shell to 9-pin D-Shell), 10 m
(32.7 ft)
2711-NC17
Remote RS-232 Serial Cable (9-Pin D-Shell to 9-Pin D-Shell)
2711-NC21
RS-232 Operating Cable (9-pin D-Shell to 8-pin Mini DIN), 5 m (16.4 ft)
2711-NC22
RS-232 Operating Cable (9-pin D-Shell to 8-pin Mini DIN), 10 m (32.7 ft)
1761-CBL-AS03
DH-485 Operating Cable (6-pin Phoenix to RJ45), 3 m (10 ft)
1761-CBL-AS09
DH-485 Operating Cable (6-pin Phoenix to RJ45), 9 m (30 ft)
1746-C10
DH-485 Network Interface Cable (SDL AMP to RJ45), 1.83 m (6 ft)
1746-C11
DH-485 Network Interface Cable (SDL AMP to RJ45), .3 m (1 ft.)
1784-CP14
DH-485 Network Interface Cable (5-pin Phoenix to RJ45)
2711P-CBL-EX04
Ethernet CAT5 Crossover Cable, Industrial Grade, 4.3 m (14 ft)
2711P-CBL-US02
USB to Serial Network Interface Cable
2711P-CBL-UU02
USB Host-to-Host Data Transfer Cable
Communication Adapters
Cat. No.
Description
2711P-CBL-UP02
USB to PS/2 Adapter
1761-NET-AIC
AIC+ Advanced Interface Converter
1747-AIC
DH-485 Isolated Link Coupler for use with DH-485 Communication Modules
(2711P-RN3, 2711P-RN6)
Remote AC Power Supply (700 - 1500 only)
Publication 2711P-UM001C-EN-P
Cat. No.
Description
2711P-RSACDIN
AC to DC DIN Rail Power Supply, 85…265V ac, 47…63 Hz
Overview
1-17
Miscellaneous
Cat. No.
Description
2711P-RVT12
Solar Visor for Outdoor High-Bright 1250 Touch Screen Display Modules
2711P-RY2032
Replacement Battery for 700 - 1500 terminals
2711P-RTMC
Replacement Mounting Clips for 700 - 1500 terminals
2711P-RTFC
Replacement Mounting Levers for 400 - 600 terminals
2711P-RVAC
Replacement AC Power Terminal Block for 400 - 600 terminals
2711-TBDC
Replacement DC Power Terminal Block for 400 - 600 terminals
6189-2CONN
Replacement AC/DC Connectors for PanelView Plus 700 - 1500 terminals
Firmware Upgrade Kits
Cat. No.
Description
2711P-RU310
PanelView Plus Media Kit includes Firmware Upgrade Wizard, 1 Firmware
License, Certificate of Authenticity, End User License Agreement.
2711P-RUA310 PanelView Plus Advanced Media Kit includes the 2711P-RU310 Media Kit,
PCMCIA to Compact Flash Adapter, and 32 MB Compact Flash Card.
2711P-RUL01
Firmware Upgrade License Kit with (1) PanelView Plus Firmware License. (1)
2711P-RUL05
Firmware Upgrade License Kit with (5) PanelView Plus Firmware Licenses. (1)
2711P-RUL10
Firmware Upgrade License Kit with (10) PanelView Plus Firmware Licenses.(1)
2711P-RUL25
Firmware Upgrade License Kit with (25) PanelView Plus Firmware Licenses. (1)
2711P-RUL50
Firmware Upgrade License Kit with (50) PanelView Plus Firmware Licenses. (1)
(1)
Also includes Certificate of Authenticity, End User License Agreement, Installation Instructions.
Publication 2711P-UM001C-EN-P
1-18
Overview
Publication 2711P-UM001C-EN-P
Chapter
2
Installation
Chapter Objectives
This chapter provides instructions on how to install the PanelView
Plus terminals. It provides information on:
• hazardous locations
• environment
• enclosures
• clearances
• outdoor installation (1250 High-Bright Display only)
• required tools
• cutout dimensions
• mounting dimensions
• 400 - 600 panel installation
• 700 - 1500 panel installation
Hazardous Locations
This PanelView Plus terminals are suitable for use in:
• Class I, Division 2, Groups A, B, C, D
• Class I, Zone 2, Group IIC
• Class II, Division 2, Groups F, G
• Class III
• or (ordinary) non-hazardous locations
The following statement applies to use in hazardous locations.
WARNING
!
Explosion Hazard
• Substitution of components may impair suitability
for hazardous locations.
• Do not disconnect equipment unless power has
been switched off and area is known to be
non-hazardous.
• Do not connect or disconnect components unless
power has been switched off.
• All wiring must comply with N.E.C. articles
501-4(b), 502-4(b), 503-3(b) as appropriate.
• Peripheral equipment must be suitable for the
location it is used in.
The PanelView Plus terminals have a temperature code of T4 when
operating in a 55 °C (131 °F) maximum ambient temperature. Do not
install the terminals in environments where atmospheric gases have
ignition temperatures less than 135 °C (275 °F).
1
Publication 2711P-UM001C-EN-P
2-2
Installation
USB Ports
The PanelView Plus Terminals contain USB (Universal Serial Bus)
ports which comply with hazardous location environments. The
400/600 terminal has one USB port; the 700-1500 terminals have two
USB ports. This section details the field wiring compliance
requirements and is provided in accordance with the National
Electrical Code, article 500.
PanelView Plus 400/600 Host Product
USB Port
Associated Nonincendive Field
Wiring Apparatus
USB
Peripheral
Device
The USB peripheral device must be rated for use in the hazardous
location environment in which it is used and also comply with the
circuit parameters in Table 2.2.
The circuit parameters in Table 2.1 define the maximum voltage and
current of the PanelView Plus USB ports.
Table 2.1 PanelView Plus USB Port Circuit Parameters
Parameter
Value
Parameter Definition
V oc
5.25V dc
Open circuit voltage of the host USB port.
I sc
1.68 A
Maximum output current of the host USB port.
The circuit parameters in Table 2.2 define the maximum voltage,
current, capacitance, and inductance values for any peripheral device
connected to a PanelView Plus USB port in a hazardous location
environment.
Table 2.2 Required Circuit Parameters for the USB Peripheral Device
Parameter
Value
Parameter Definition and Application Requirement
V max
5.25V dc
Maximum applied voltage rating of the USB peripheral device.
Vmax shall be greater than or equal to Voc in Table 2.1. (Vmax ≥ Voc )
I max
1.68 A
Maximum current to which the USB peripheral device can be
subjected. I max shall be greater than or equal to Isc in Table 2.1.
(Imax ≥ Isc)
Ca
10 µF
Maximum allowed capacitance of the USB peripheral device and its
associated cable. The sum of Cint of the USB peripheral device and
Ccable of the associated cable shall be less than or equal to Ca.
(Cint + Ccable ≤ Ca)
La
15 µH
Maximum allowed inductance of the USB peripheral device and its
associated cable. The sum of Lint of the USB peripheral device and
Lcable of the associated cable shall be less than or equal to La.
(Lint + Lcable ≤ La)
Publication 2711P-UM001C-EN-P
Installation
2-3
Application Information
Per the National Electrical Code, the circuit parameters of associated
field wired apparatus for use in hazardous locations shall be
coordinated with the host product such that their combination
remains nonincendive. The PanelView Plus terminal and the USB
peripheral device shall be treated in this manner.
The circuit parameters of the PanelView Plus USB ports are given in
Table 2.1. The USB peripheral device and its associated cabling shall
have circuit parameters with the limits given in Table 2.2 for them to
remain nonincendive when used with the PanelView Plus USB port. If
cable compliance and inductance are not known, use the following
values from UL 913:
Ccable = 60 pF/ft
Lcable = 0.20 µH/ft
Environmental
Considerations
The PanelView Plus terminals are suitable for use in an industrial
environment when installed in accordance with these instructions.
Specifically, this equipment is intended for use in clean, dry
environments (Pollution Degree 2(1) and with circuits not exceeding
Over Voltage Category II(2) (IEC 60664-1).(3)
(1) Pollution Degree 2 is an environment where, normally only non-conductive pollution occurs except that
occasionally a temporary conductivity caused by condensation shall be expected.
(2) Over Voltage Category II is the load level section of the electrical distribution system. At this level transient
voltages are controlled and do not exceed the impulse voltage capability of the product’s insulation.
(3) Pollution Degree 2 and Over Voltage Category II are International Electrotechnical Commissions (IEC)
designations.
Enclosures
The terminals must be mounted in a panel or enclosure to protect the
internal circuitry. The terminals meet IP54, IP65 and NEMA Type
12/13 and 4X (indoor) ratings only when mounted in a panel or
enclosure with the equivalent rating. When the terminal is not
mounted in a panel, it is not secure or safe for operation. You must
comply with NEMA Type 4X (indoor) requirements for environmental
specifications. For more enclosure and certification information on the
Outdoor High-Bright Display Module, refer to publication
2711P-IN026.
Publication 2711P-UM001C-EN-P
2-4
Installation
Clearances
You must allow adequate clearances around the terminal, inside the
enclosure, for adequate ventilation. Consider heat produced by other
devices in the enclosure. The ambient temperature around the
terminals must be between 0…55 °C (32…131 ºF).
Clearance
400 - 600 Terminals
700 - 1500 Terminals
Top
51 mm (2 in)
51 mm (2 in)
Bottom
102 mm (4 in)
51 mm (2 in)
Side(1)
25 mm (1 in)
25 mm (1 in)
Back
none
none
(1)
Outdoor Installation
Maximum side clearance for insertion of memory card and cable wiring is 102 mm (4 in).
When using the High-Bright Display Module outdoors, the following
are important in maximizing the field life of the front bezel and
display:
• selecting proper enclosure
• orientation of the terminal
Both ultraviolet and infrared radiation can reduce the field life of any
electronic device. While the materials used in the PanelView Plus
bezels provide long field life, that life can be improved by proper
installation.
Ultraviolet radiation from the sun causes all plastics to fade or yellow
and become brittle over time. Using an antiglare overlay
(2711P-RGT12) will protect the front of the terminal from direct
exposure to UV radiation and greatly increase its field life.
When installing the High-Bright Display Module in an environment
where the front of the terminal will be in direct sunlight during the
hottest part of the day and the external ambient temperature can
exceed 40 oC (104 oF), use the 2711P-RVT12 visor kit. The visor
reduces the solar load on the front of the display and helps to
maintain internal temperatures within specification.
The High-Bright Display Module has a built in temperature sensor that
automatically reduces the backlight intensity if the temperature inside
the cabinet exceeds 55 oC. This reduces the risk of damage to the
display.
The paint color, size and power dissipated by the internal components
of an enclosure affect the temperature rise inside the cabinet.
Hoffman, a Rockwell Automation Encompass Partner, has information
to assist you with enclosure selection and heating/cooling accessories
to meet the temperature requirements of the installed equipment. See
website http://www.hoffmanonline.com.
Publication 2711P-UM001C-EN-P
Installation
2-5
Stirring fans or active cooling may be required in high altitude and
high ambient temperature locations to keep the internal enclosure
temperature below 55 oC (131 °F). Use a heater in installations where
the ambient temperature is below 0 oC (32 oF) for any length of time.
The backlight of the high-bright display generates a significant amount
of heat when set to full intensity. To minimize the amount of heat
generated and extend the life of the backlight, decrease the display
intensity by using the screen saver with a 5 - 10 minute delay.
Avoid placing the terminal on the south (north in the southern
hemisphere) or west side of the cabinet, if possible. This will reduce
the heat rise due to solar loading during the hottest part of the day.
Mount the terminal vertically to minimize solar loading on the display.
Do not mount the terminal in a sloped enclosure if it will be exposed
to direct sunlight.
Required Tools
Besides the tools required for the panel or enclosure cutouts, you will
need the following for installation:
• small slotted screw driver for securing power and RS-232
connections
• torque wrench (N•m/in-lb) for tightening the mounting clips on
the PanelView Plus 700 - 1500 terminals
Cutout Dimensions
This section provides panel cutout dimensions for each terminal. Use
the full size template shipped with your terminal to mark the cutout
dimensions. All dimensions are in mm (inches).
PanelView Plus Terminal
Height
Width
400 Keypad
123 (4.86)
156 (6.15)
600 Keypad or Keypad & Touch
142 (5.61)
241 (9.50)
600 Touch
123 (4.86)
156 (6.15)
PanelView Plus 700 Keypad or Keypad & Touch
167 (6.57)
264 (10.39)
PanelView Plus 700 Touch
154 (6.08)
220 (8.67)
PanelView Plus 1000 Keypad or Keypad & Touch
224 (8.8)
375 (14.75)
PanelView Plus 1000 Touch
224 (8.8)
305 (12.00)
PanelView Plus 1250 Keypad or Keypad & Touch
257 (10.11)
390 (15.35)
PanelView Plus 1250 Touch / 1250 High-Bright Touch 257 (10.11)
338 (13.29)
PanelView Plus 1500 Keypad or Keypad & Touch
305 (12.00)
419 (16.50)
PanelView Plus 1500 Touch
305 (12.00)
391 (15.40)
Publication 2711P-UM001C-EN-P
2-6
Installation
Mounting Dimensions
This section provides mounting dimensions for the entire line of
PanelView Plus terminals. All measurements are in mm (inches).
PanelView Plus 400
152
(6.0)
185 (7.28)
90
3.54)
60
(2.35)
71 (2.81)
154 (6.08)
Publication 2711P-UM001C-EN-P
Installation
2-7
PanelView Plus 600
600 Keypad or Keypad & Touch Terminal
167
(6.58)
68
(2.68)
98
(3.86)
71 (2.81)
268 (10.47)
154 (6.08)
600 Touch Terminal
152
(6.0)
68
(2.68)
98
(3.86)
71 (2.81)
185 (7.28)
154 (6.08)
Publication 2711P-UM001C-EN-P
2-8
Installation
PanelView Plus 700
The depth dimensions are shown for:
• base configured unit (Display Module and Logic Module)
• base configured unit with Communication Module
Publication 2711P-UM001C-EN-P
Installation
2-9
PanelView Plus 1000
The depth dimensions are shown for:
• base configured unit (Display Module and Logic Module)
• base configured unit with Communication Module
1000 Keypad or Keypad & Touch Terminal
a 55 (2.18) Display to Logic Module
b 83 (3.27) Display to Communication Module
248
(9.77)
a
b
399
(15.72)
1000 Touch Screen Terminal
a 55 (2.18) Display to Logic Module
b 83 (3.27) Display to Communication Module
248
(9.77)
a
b
329
(12.97)
Publication 2711P-UM001C-EN-P
2-10
Installation
PanelView Plus 1250
The depth dimensions are shown for:
• base configured unit (Display Module and Logic Module)
• base configured unit with Communication Module
1250 Keypad or Keypad & Touch Terminal
a 55 (2.18) Display to Logic Module
b 83 (3.27) Display to Communication Module
282
(11.12)
a
b
416
(16.36)
1250 Touch Screen Terminal
a 55 (2.18) Display to Logic Module
b 83 (3.27) Display to Communication Module
a
b
282
(11.12)
1250
a 74 (2.90) Display to Logic Module
b 101 (3.99) Display to Communication Module
363
(14.30)
a
b
1250 High-Bright
Publication 2711P-UM001C-EN-P
Installation
2-11
PanelView Plus 1500
The depth dimensions are shown for:
• base configured unit (Display Module and Logic Module)
• base configured unit with Communication Module
1500 Keypad or Keypad & Touch Terminal
330
(12.97)
a 65 (2.55) Display to Logic Module
b 93 (3.65) Display to Communication Module
a
b
419
(18.46)
1500 Touch Screen Terminal
a 65 (2.55) Display to Logic Module
b 93 (3.65) Display to Communication Module
330
(12.97)
a
b
416
(16.37)
Publication 2711P-UM001C-EN-P
2-12
Installation
400 - 600 Panel Installation
The PanelView Plus 400 and 600 terminals are installed in the same
manner using mounting levers. The number of levers used (4 or 6)
varies by terminal type. The mounting levers are shipped with each
terminal.
ATTENTION
!
• Disconnect all electrical power from the panel
before making the panel cutout.
• Make sure the area around the panel cutout is
clear.
• Do not allow metal cuttings to enter any
components already installed in the panel.
• Failure to follow these instructions may result in
personal injury or damage to panel components.
To install terminal in a panel:
1. Cut an opening in the panel using the panel cutout provided
with the terminal. Remove any sharp edges or burrs.
2. If Communication Module is ordered separately, attach module
to the base unit before panel installation. Refer to the
instructions shipped with module.
3. Make sure the terminal sealing gasket is properly positioned on
the terminal as shown. This gasket forms a compression type
seal. Do not use sealing compounds.
Sealing Gasket
4. If using keypad legend strips on the 600 keypad terminals, we
recommend that you install the strips before installing the
terminal. Be careful not to pinch legend strip during installation.
5. Place the terminal in the panel cutout.
If installing terminal in existing 550 panel cutout, align terminal
with center of cutout for best gasket sealing.
Publication 2711P-UM001C-EN-P
Installation
2-13
6. Insert all mounting levers (4 or 6) into the mounting slots on the
terminal (as shown below). Slide each lever until flat side of
lever touches the surface of the panel.
Mounting Slots
Mounting Levers
Flat Side of Lever
7. When all levers are in place, slide each lever an additional notch
or two until you hear a click.
8. Rotate each lever in direction indicated until lever is in final
latch position. Follow the latching sequence below to obtain
optimum terminal fit.
1
4
4 Levers
Notch
6
3
1
Alignment Marks
1
Rotate lever until notch in
lever aligns with proper
alignment mark on terminal.
2
5
3
6 Levers
4
2
6
Use the table below as a guide to insure an adequate gasket seal
between terminal and panel.
Lever Position
1
3 2
6 5 4
Terminal Markings
or Alignment
Typical Gauge
1
0.15 - 2.01 mm (0.060 - 0.079 in)
16
2
2.03 - 2.64 mm (0.08 - 0.104 in)
14
3
2.67 - 3.15 mm (0.105 - 0.124 in)
12
4
3.17 - 3.66 mm (0.125 - 0.144 in)
10
5
3.68 - 4.16 mm (0.145 - 0.164 in)
8/9
6
4.19 - 4.75 mm (0.165 - 0.187 in)
7
ATTENTION
!
Panel Thickness Range
Follow instructions above to provide a proper
seal and to prevent potential damage to the
terminal. Allen-Bradley assumes no
responsibility for water or chemical damage to
the terminal or other equipment within the
enclosure because of improper installation.
Publication 2711P-UM001C-EN-P
2-14
Installation
700 - 1500 Panel Installation
The PanelView Plus 700 - 1500 terminals are installed in the same
manner using clips for mounting. The number of clips used (4, 6 or 8)
varies by terminal type. The mounting clips are shipped with each
terminal.
ATTENTION
!
• Disconnect all electrical power from the panel
before making the panel cutout.
• Make sure the area around the panel cutout is
clear.
• Do not allow metal cuttings to enter any
components already installed in the panel.
• Failure to follow these instructions may result in
personal injury or damage to panel components.
To install a PanelView Plus terminal in a panel:
1. Cut an opening in the panel using the panel cutout provided
with the terminal. Remove any sharp edges or burrs.
2. Make sure the terminal sealing gasket is properly positioned on
the terminal as shown. This gasket forms a compression type
seal. Do not use sealing compounds.
Sealing Gasket
3. If using keypad legend strips on keypad terminals, we
recommend that you install the strips before installing the
terminal. Be careful not to pinch the legend strip during
installation.
4. Place the terminal in the panel cutout.
Publication 2711P-UM001C-EN-P
Installation
2-15
5. Install the mounting clips. The ends of the clips slide into the
slots on the terminal.
Mounting Clip
Mounting Clip Slot
6. Tighten the clip mounting screws by hand until the gasket seal
contacts the mounting surface uniformly.
7. Alternately tighten the mounting clips screws to a torque of
.90 - 1.1 N•m (8 - 10 in-lb). Do not over-tighten.
1
4
1
Torque Sequence
for 4 Clips
3
2
5
3
Torque Sequence
4
2
1
3
6
Torque Sequence
!
8
4
7
5
ATTENTION
6
2
Tighten the mounting clip screws to a torque
of .90 - 1.1 N•m (8 - 10 in-lb) to provide a
proper seal and to prevent potential damage to
the terminal. Allen-Bradley assumes no
responsibility for water or chemical damage to
the terminal or other equipment within the
enclosure because of improper installation.
Publication 2711P-UM001C-EN-P
2-16
Installation
Publication 2711P-UM001C-EN-P
Chapter
3
Applying Power
Chapter Objectives
This chapter provides information on:
• wiring and safety guidelines
• removing and installing power terminal block
• connecting DC power
• connecting AC power
• resetting the terminal
• startup sequence
Wiring and Safety
Guidelines
Use publication NFPA 70E, "Electrical Safety Requirements for
Employee Workplaces", IEC 60364 "Electrical Installations in
Buildings" or other applicable wiring safety requirements for the
country of installation when wiring the VersaView CE terminals. In
addition to the NFPA guidelines:
• connect the terminal and other similar electronic equipment to
its own branch circuit.
• protect the input power by a fuse or circuit breaker rated at no
more than 15 Amps.
• route incoming power to the terminal by a separate path from
the communication lines.
• where power and communication lines must cross, they should
cross at right angles.Communication lines can be installed in the
same conduit as low level DC I/O lines (less than 10 volts).
• shield and ground cables appropriately to avoid Electromagnetic
Interference (EMI). Grounding minimizes noise from EMI and is
a safety measure in electrical installations.
For additional grounding recommendations, refer to the National
Electrical Code published by the National Fire Protection Association
of Boston.
1
Publication 2711P-UM001C-EN-P
3-2
Applying Power
Installing and Removing
Power Terminal Block
You can remove and re-install the DC or AC power terminal block for
ease of installation, wiring, and maintenance. The terminal block is
pre-installed when shipped.
WARNING
!
ATTENTION
!
ATTENTION
!
Explosion Hazard
• Substitution of components may impair suitability
for hazardous locations.
• Do not disconnect equipment unless power has
been switched off and area is known to be
non-hazardous.
• Do not connect or disconnect components unless
power has been switched off.
• All wiring must comply with N.E.C. articles
501-4(b), 502-4(b), 503-3(b) as appropriate.
• Peripheral equipment must be suitable for the
location it is used in.
Disconnect all power before installing or replacing
components. Failure to disconnect power may result
in electrical shock and/or damage to the terminal.
AC and DC terminal blocks are keyed and marked
differently so be sure to follow markings. Do not
force terminal blocks into connectors to prevent
potential damage to terminal.
400 - 600 Terminals
To remove terminal block:
1. Insert tip of small,
flat-blade, screw driver into
terminal block access slot.
2. Gently pry terminal block
away from terminal to release
locking mechanism
To install terminal block:
1. Press terminal block base in
first with block leaning outward.
Publication 2711P-UM001C-EN-P
2. Gently push top of terminal block back
to vertical position to snap in locking tab.
Applying Power
3-3
700 - 1500 Terminals
To remove terminal block:
1. Loosen the two screws
that secure the terminal
block.
2. Gently pull the terminal
block away from the
connector.
To install terminal block:
1. Re-attach the terminal block
to the connector until seated.
2. Replace the 2 screws that secure the
terminal block to the connector.
Connecting DC Power
The PanelView Plus terminals have an integrated DC power supply.
The electrical input ratings for DC power are:
Power Type
DC
Terminal
Input Range
400 - 600
24V dc nominal (18…30 V dc)
25 Watts maximum (1.0 A at 24V dc)
700 - 1500
24V dc nominal (18…32 V dc)
70 Watts maximum (2.9 A at 24V dc)
The DC power supply is internally protected against reverse polarity.
The input power terminal block on the integrated power supply is
removable and supports the following wire sizes:
Terminal
Wire Type
Wire Size
(2-wire maximum per terminal)
400 - 600
Stranded or Solid
#18 to #12 AWG
Stranded
#16 to #22 AWG
Solid
#18 to #22 AWG
700 - 1500
Terminal Block
Screw Torque
.23 - .45 N•m (2 - 4 in-lbs)
PanelView Plus terminals using 24V dc power are EN 61131-2
Equipment Class II devices.
Publication 2711P-UM001C-EN-P
3-4
Applying Power
ATTENTION
!
ATTENTION
!
For DC powered units, use a Class 2/SELV (Safety
Extra-Low Voltage) isolated and ungrounded
power supply as input power to the PanelView
Plus terminal. This power source provides
protection so that under nominal and single fault
conditions, the voltage between conductors and
between conductors and Functional
Earth/Protective Earth does not exceed a safe
value.
Explosion Hazard - Do not connect or disconnect
equipment while circuit is live unless area is known
to be non-hazardous.
Disconnect all power before installing or replacing
components. Failure to disconnect power may result
in electrical shock and/or damage to the terminal.
To connect DC power:
1. Secure the DC power wires to the terminal block screws. Follow
the markings on terminal blocks and labels on terminal for
proper connections.
2. Secure the Earth Ground wire to the appropriate terminal block
screw.
700 - 1500 Terminals
400 - 600 Terminals
+ DC Positive
- DC Negative
Functional
Earth Ground
+ DC Positive
Functional Earth Ground
- DC Negative
3. Apply 24V dc power to the terminal.
Publication 2711P-UM001C-EN-P
Applying Power
Connecting AC Power
3-5
The PanelView Plus 400 - 600 terminals are available with an
integrated AC power supply. A DIN Rail mounted AC power supply is
available as a separate catalog number for the PanelView Plus 700 1500 terminals.
Power Type
AC
(1)
Terminal
Input Range
400 - 600
85…264V ac (47…63 Hz)
60 VA maximum
700 - 1500(1)
85…264V ac (47…63 Hz)
120 VA maximum
Requires the DIN Rail Mounted AC power supply (2711P-RSACDIN). For more information, see installation
instructions shipped with power supply.
The input power terminal block on the PanelView Plus 400-600
integrated power supply is removable and supports these wire sizes:
Terminal
Wire Type
Wire Size
(2-wire maximum per terminal)
400 - 600
Stranded or Solid
#18 to #12 AWG
Terminal Block
Screw Torque
.23 - .45 N•m (2 - 4 in-lbs)
PanelView Plus 400 and 600 terminals using AC power are EN 61131-2
Equipment Class I devices.
ATTENTION
!
ATTENTION
!
Explosion Hazard - Do not connect or disconnect
equipment while circuit is live unless area is known
to be non-hazardous.
Disconnect all power before installing or replacing
components. Failure to disconnect power may result
in electrical shock and/or damage to the terminal.
Improper wiring of power terminals may result in
voltage at the communication connector shells. Refer
to the following figure when wiring.
Do not apply power to the terminal until all wiring
connections have been made. Failure to do so may
result in electrical shock.
Publication 2711P-UM001C-EN-P
3-6
Applying Power
To connect AC power:
1. Secure the AC power wires to the terminal block screws.
2. Secure the Earth Ground wire to the appropriate terminal block
screw.
L1 L2N
L1
Protective
Earth Ground
L2/N
3. Apply power to the terminal.
Resetting the Terminal
400 - 600 Terminals
The PanelView Plus 400 and 600 terminals have a Reset switch on the
side of the terminal. Use the Reset switch to restart the terminal
without having to disconnect and reapply power. When reset, the
terminal will perform a series of startup tests and run RSView ME. The
loaded .MER application may also run depending on how the terminal
is configured.
Reset Switch
Press Reset with your finger or a nonconducting object.
ATTENTION
!
Publication 2711P-UM001C-EN-P
Use a nonconducting object to press the RESET
switch. Do not use a conducting object such as a
paper clip or you may damage the terminal. Do not
use the tip of a pencil; graphite may damage the
terminal.
Applying Power
3-7
700 - 1500 Terminals
The PanelView Plus 700 - 1500 terminals have both a Reset switch and
a Default switch on the side of the logic module.
Default
Reset
Reset
Use the RESET switch to restart the terminal without having to
disconnect and reapply power. Insert a thin probe into the hole
marked RESET and press the switch. The terminal will perform a
series of startup tests and run RSView ME. The loaded .MER
application may also run depending on how the terminal is
configured.
Default
Use the DEFAULT switch with the RESET switch to start the terminal in
Safe Mode. This is a diagnostics mode where the system is reduced to
a known state that allows recovery from a software problem. Safe
Mode ignores all user changes to the system and avoids any problem
that is due to interactions with end-user software or changes.
For more details on Safe Mode, refer to page 8-13.
• Insert a thin probe into the hole marked DEFAULT and press the
switch, then;
• Insert the probe into the hole marked RESET and press the
switch. The system will restart immediately into the Safe Mode.
ATTENTION
!
Use a nonconducting object to press the RESET and
DEFAULT switch. Do not use a conducting object
such as a paper clip or you may damage the
terminal. Do not use the tip of a pencil; graphite
may damage the terminal.
Publication 2711P-UM001C-EN-P
3-8
Applying Power
Startup Sequence
After a reset, the PanelView Plus performs a series of startup tests and
then either:
• runs the .MER application currently loaded in the terminal
• enters PanelView Plus configuration mode
The action that occurs depends on what startup options are
configured for your PanelView Plus terminal.
Publication 2711P-UM001C-EN-P
Chapter
4
Using Configuration Mode
Chapter Objectives
This chapter shows how to use the configuration screens of your
PanelView Plus terminal to:
•
•
•
•
•
Starting Configuration
Mode
perform data entry and navigation
load an ME application
run an ME application
modify application settings
modify terminal settings
When you reset or start up the PanelView Plus, you should
automatically enter Configuration Mode. Your application will
automatically run on startup if you configured this option under
Terminal Settings>Startup Options.
If you are unable to enter configuration mode, see page 8-14 in
Chapter 8, Troubleshooting.
To access Configuration Mode from a running application:
• press the Goto Configuration Mode button.
This button is added to application screen in RSView Studio.
The application stops running but is still loaded.
Name of application that is currently loaded.
Only appears if application is loaded.
To activate buttons:
• on keypad terminals, select the
corresponding function key [Fx]
• on touch screen terminals, tap the
button with your finger or stylus.
• if a mouse is attached, make
selections with the mouse.
1
Publication 2711P-UM001C-EN-P
4-2
Using Configuration Mode
Main Screen Button
Description
Load Application (F1)
Opens another screen where you can select an application to
load. Once loaded, the application name will appear under
Current Application.
Run Application (F2)
Runs the .MER application displayed under Current Application.
An application must be loaded before you can run it.
Application Settings (F3)
Opens a menu of application-specific configuration settings.
Terminal Settings (F4)
Opens a menu of options to configure non-application, specific
terminal settings for the PanelView Plus terminal.
Delete Log Files Before
Running (F5)
Toggles between Yes and No. If you select Yes, all data log files,
alarm history and alarm status file will be deleted before the
application is run. If you select No, log files are not deleted first.
Reset (F7)
Resets the terminal. The action that occurs on startup depends
on whether you defined shortcut paths in the Windows Startup
folder.
Exit (F8)
Exits Configuration Mode.
Data Entry and Navigation
Configuration Mode uses screen buttons for data entry and navigation.
• On terminals with a touch screen, tap the button with your
finger or stylus.
• On terminals with a keypad, select the function key listed on the
button, or in some cases, the corresponding key on the keypad.
Besides operation specific buttons which are used to modify
configuration data, most screens have a combination of the following
buttons.
Screen Buttons
Close
[F8]
OK
[F7]
Cancel
[F8]
Description
Returns to the previous screen.
Accepts modified values and returns to
previous screen.
Cancels the current operation without
saving any changes.
Moves highlight up or down a list.
Selects a highlighted screen or item from a
list.
Publication 2711P-UM001C-EN-P
Using Configuration Mode
4-3
Input Panel
Many screens have buttons that access fields where you must
enter/edit data. When you press the button or function key, the Input
Panel opens ready for you to input data.
If the field is restricted to a numeric value, only the 0-9 keys will be
enabled. If the value is an IP address, the 0-9 and decimal point keys
will be enabled. All other buttons will be disabled.
Display Area
PanelView Plus
Character Keyboard
• on a touch terminal, tap the keys.
• on a keypad terminal, use the
arrow keys on the keypad to
select keys.
• If a mouse is attached, use the
mouse to select keys.
Controls
Controls
Function
SHF
Switches keys between their shifted and unshifted state. The initial default is shifted.
CAPS
Switches keys between lowercase and uppercase characters. The initial default is lowercase.
SPACE
Enters a space between characters in the Display Area.
Backspace
Deletes the previous character (to the left of the cursor) in the Display Area.
Select
Selects a character and enters it in the Display Area.
Right, Left, Up, Down Arrow Keys
Selects the character to the right, left, above or below the currently selected character.
Enter
Accepts the entered characters and returns to the previous screen
ESC
Cancels the current operation and returns to the previous screen.
To enter characters in the Display Area:
1. Select a character on the Character Keyboard.
2. Press the Select button to copy the character to the Display
Area.
3. When done entering all characters, press Enter. You will return
to the previous screen.
You will return to the previous screen with the newly data entered.
Publication 2711P-UM001C-EN-P
4-4
Using Configuration Mode
Loading an ME Application
To load an RSView ME .MER application, select the Load Application
button on the main screen:
List of .mer applications
stored in the compact
flash of the terminal.
Moves
highlight up
Moves
highlight down
1. Select the Source button to select the storage location of the
application file you want to load. The options are:
• Internal Storage - the Internal Compact Flash in the PanelView
Plus terminal.
• External Storage 1 - the External Compact Flash card loaded in
the card slot of the terminal.
• External Storage 2 - for future use.
TIP
RSView ME only recognizes files located in the
\RockwellSoftware\RSViewME\Runtime\
folder.
2. Select an .MER file from the list. Use the up and down cursor
keys to select a file.
3. Select the Load button to load the application.
You will be asked if you want to replace the terminals’ current
communication configuration with the application’s
communication configuration.
4. Select Yes or No. If you select Yes, any changes made to the
device addresses or driver properties in the RSLinx
Communications screen will be lost.
The name of the currently loaded application will appear at the top of
the main Configuration Mode screen.
Publication 2711P-UM001C-EN-P
Using Configuration Mode
4-5
Running an Application
To run the currently loaded application, select the Run Application
button on the main Configuration Mode screen. An application must
be loaded, before you can run it. Log files generated by the
application may be deleted if this option was selected on the main
screen or enabled as a Startup Option under Terminal Settings.
Application Settings
From the Application Settings screen, you can show device shortcuts
defined for the loaded .MER application. For example, your .MER
application might have SLC defined as a device shortcut name for the
SLC 5/05. Device shortcuts are read-only and cannot be edited.
Terminal Settings
From Terminal Settings, you can open screens to configure and
modify non-application settings for the PanelView Plus terminal.
• On a touch terminal, tap the
button.
• On a keypad terminal, press
the corresponding key on the
keypad
Diagnostics Setup
Display
File Management
Font Linking
Input Devices
Networks and Communications
Print Setup
Startup Options
System Event Log
System Information
Time/Date/Regional Settings
Moves highlight up
Moves highlight down
Selects highlighted
item and opens screen
Returns to previous
screen.
Terminal Setting
Description
Diagnostic
Forwards diagnostic messages form a remote log
destination to a computer running diagnostics.
Display
Shows the temperature of the display, sets the intensity of
the backlight, contrast of grayscale displays, and
enables/disables the screen saver.
File Management
Copies or deletes application files or font files from a
storage location.
Font Linking
Links a font file to a base font loaded on the terminal.
Input Devices
Configures settings for the keypad, touch screen, or
attached keyboard and mouse.
Networks and Communications
Configures network connections and communication
settings specific to the application (DHPlus, DH485,
Remote I/O, ControlNet, Serial).
Print Setup
Configures settings for printing displays, alarm messages,
and diagnostics messages generated by the application.
Publication 2711P-UM001C-EN-P
4-6
Using Configuration Mode
Networks and
Communications
Terminal Settings
Networks and Communications
KEPServer Serial Port ID’s
Publication 2711P-UM001C-EN-P
Terminal Setting
Description
Startup Options
Specifies whether the terminal starts up in configure or
run mode. Also lets you enable/disable tests to run on the
terminal at startup.
System Event Log
Displays a list of system events currently logged by the
terminal.
System Information
Displays power, temperature, battery and memory details
for the terminal. Also shows the firmware number for
RSView ME and technical support information.
Time/Date/Regional Settings
Sets the date, time, language and numeric format used by
the terminal and applications.
From the Networks and Communications screen, you can access
settings for:
• KEPServer Serial Port ID’s
• Network Connections
• RSLinx Enterprise Communications
KEPServer Serial Port ID’s
To access the KEPServer Serial Port ID’s screen, you must have
KEPServer Enterprise installed on your terminal. Otherwise, you will
get an error message when accessing this screen. If you plan on using
KEPServer Enterprise and serial communications, you must specify
which COM port to use.
Using Configuration Mode
4-7
Terminal Settings
RSLinx Enterprise Communications
Networks and Communications
The RSLinx Enterprise Communications screen shows a treeview of
installed communication cards and network configurations. You can:
RSLinx Enterprise Communications
• edit/view the driver settings for the communication protocol
used by your .MER application.
• edit the device address of the controller on the network.
The procedure for editing these settings is the same regardless of the
communication protocol. The only differences are the properties for
each communication protocol and the device address of the logic
controller. The properties for each communication protocol are
defined immediately after this section.
Ethernet Driver
Has no properties to edit.
Communication Driver
AB_ETH-1
<No Devices>
Serial-DF1
<No Devices>
Publication 2711P-UM001C-EN-P
4-8
Using Configuration Mode
To edit communication settings:
1. From the RSLinx Configuration Screen, select the communication
card installed on your terminal.
2. Select the Driver Settings button.
A properties screen opens showing the current communication
settings for the driver.
3. To modify a setting, select the setting and then the Edit button.
The Input Panel opens showing the current setting.
4. Using the Input Panel, modify the setting and then select the
Enter button.
You return to the previous screen with the newly entered data.
To edit the device address of the logic controller:
1. From the RSLinx Configuration screen, select a device node.
2. Select the Edit Device button.
A screen opens showing the name of the device and its current
node address.
3. To modify the device address, press the Device Address button.
The Input Panel opens showing the current address.
4. Using the Input Panel, modify the address and then select the
Enter button.
You return to the previous screen with the new address.
IMPORTANT
Publication 2711P-UM001C-EN-P
Modified settings do take effect until the terminal is
rebooted.
Using Configuration Mode
4-9
DHPlus Properties
The DHPlus Properties screen lets you view or modify settings for a
PanelView Plus connected to a DHPlus network.
Field
Description
Valid Values
Jumper ID(1)
Identifies the communication card if multiple
cards are installed on terminal.
0-3
Station Number
The unique address of the PanelView Plus on
the DHPlus network.
0 - 77 (octal)
Baud Rate
The baud rate of the DHPlus network.
57600 (default)
115200
230400
(1)
For use with PanelView Plus 700-1500 terminals only.
DH485 Properties
The DH485 Properties screen lets you view or modify settings for a
PanelView Plus connected to a DH-485 network.
Field
Description
Valid Values
Jumper ID(1)
Identifies the communication card if multiple
cards are installed on terminal.
0-3
Station Number
The unique station number of the PanelView
Plus on the DH-485 network.
0 - 31 (decimal)
Baud Rate
The baud rate of the DH-485 network.
9600
19200
MaxStationNumber The maximum station number on the DH-485
network. The value must be greater than or
equal to the Station Number.
(1)
0-31 (decimal)
For use with PanelView Plus 700-1500 terminals only.
Remote I/O Properties
The RIO Properties screen configures Remote I/O communication
settings for the PanelView Plus terminal on a Remote I/O link.
Field
Description
Valid Values
Jumper ID(1)
Identifies the communication card if multiple
cards are installed on terminal.
0-3
Baud Rate
The baud rate of the Remote I/O network.
57600 (default)
115200
230400
(1)
For use with PanelView Plus 700-1500 terminals only.
Publication 2711P-UM001C-EN-P
4-10
Using Configuration Mode
ControlNet Properties
The ControlNet Properties screen configures ControlNet
communication settings for the PanelView Plus terminal on a
ControlNet network.
Field
Description
Valid Values
Device ID
Unique address of the PanelView Plus
terminal on the ControlNet network.
1 - 99
Serial Properties
The Serial Properties screen configures settings for serial
communications (using the RS-232 serial port) on the PanelView Plus
terminal.
Publication 2711P-UM001C-EN-P
Field
Description
Valid Values
Device
The serial device your PanelView Plus
terminal is connected to.
PLC_CH0
KF2
SLC_CH0
KF3
KFC
KFC15
AC_CH0
Error Check
Type of error checking used. Error checking is
automatically configured if Use Auto Config
is set to Yes.
BCC, CRC
Parity
Type of parity used. The parity is
automatically configured if Use Auto Config
is set to Yes.
None, Odd, Even
Stop Bits
Number of stop bits used.
1 or 2
Ack Timeout
Ack/Poll timeout value in milliseconds.
20 - 60,000 ms
Max Retries
Maximum number of retries before the serial
driver fails.
0 - 255
Station
Station number based on a specific device.
PLC_CH0
KF2
SLC_CH0
KF3
KFC
KFC15
AC_CH0
Baud Rate
Data rate at which serial driver
communicates. The baud rate is
automatically configured if Use Auto Config
is set to Yes.
110, 300, 600, 1200, 4800
9600, 19200, 38400, 115200
Use Auto Config
Automatically or manually configures the
baud rate, parity and error checking
parameters.
Yes (auto configure)
No (manual configure)
Com Port
Communication port used on the PanelView
Plus terminal.
1 (COM1)
2 (COM2)
0-77 (octal)
0-77 (octal)
0-31
0-31
1-99
1-99
0-255
Using Configuration Mode
Terminal Settings
4-11
Network Connections
Networks and Communications
Network Connections
The Network Connections screen lets you configure the following for
the PanelView Plus terminal:
• Device Name
• Network Adapters
• Network Identification
Terminal Settings
Device Name
Networks and Communications
The Device Name screen identifies the PanelView Plus terminal to
other computers on the network.
Network Connections
Device Name
PanelView Plus
2711P-PVPlus
Field
Description
Valid Values
Device Name(1)
Name that identifies the PanelView Plus
terminal to other computers on the network.
1 to 15 characters
A leading character in the
range ’a - z’ or ’A - Z’
Remaining characters in the
range ’a - z’, ’A - Z’, ’0 - 9’, or
’- ’ (hyphen)
Device Description
Provides a description of the terminal.
50 characters maximum
(1)
Check with your network administrator to determine a valid device name.
Publication 2711P-UM001C-EN-P
4-12
Using Configuration Mode
Terminal Settings
Networks and Communications
Network Connections
Network Adapters
Network Adapters
The Network Adapters screen configures driver settings for all
network adapters installed on the terminal. The only network adapter
on the PanelView Plus terminal is the (IntelR) Fast Ethernet Controller.
Press the Name Servers button and/or IP Address button to access
driver settings.
Built-in Ethernet Controller
Name Servers
Defines Name Server addresses for the Network Adapter. These
addresses are automatically assigned if DHCP is enabled for the
network adapter.
Publication 2711P-UM001C-EN-P
Field
Description
Valid Values
Primary DNS
The address of the primary DNS resolver.
xxx.xxx.xxx.xxx
Secondary DNS
The address of the secondary DNS resolver.
xxx.xxx.xxx.xxx
Primary WINS
The address of the primary WINS resolver.
xxx.xxx.xxx.xxx
Secondary WINS
The address of the secondary WINS resolver. xxx.xxx.xxx.xxx
Using Configuration Mode
4-13
IP Address
The IP Address screen identifies the IP address of the selected
network adapter. If the network the PanelView Plus is connected to
does not automatically assign an IP address, you can assign the
address in this screen.
Field
Description
Valid Values
Use DHCP
Enables or disables DHCP (Dynamic Host
Configuration Protocol) settings. DHCP
automatically allocates network devices and
configurations to newly attached devices on
the network.
Yes (default)
No
If DHCP is set to Yes, the PanelView Plus is
automatically assigned an IP address, Subnet
Mask and Gateway. The fields are disabled.
If DHCP is set to No, you can enter the IP
address, Subnet Mask and Gateway address.
IP Address
A unique address identifying the PanelView
Plus on the Ethernet network.
xxx.xxx.xxx.xxx
000.000.000.000 (default)
Range of values for the first
set of decimal numbers is
1-255 unless all fields are set
to 000. The range of values for
the last three sets of decimal
numbers is 0-255.
Subnet Mask
Address must be identical to the server
subnet mask.
xxx.xxx.xxx.xxx
Gateway
Optional Gateway address.
xxx.xxx.xxx.xxx
Mac ID
Read only field
Publication 2711P-UM001C-EN-P
4-14
Using Configuration Mode
Terminal Settings
Networks and Communications
Network Connections
Network Identification
Publication 2711P-UM001C-EN-P
Network Identification
The Network Identification screen configures settings that enable the
PanelView Plus terminal to gain access to network resources. You can
enter a user name, password and domain (provided by your network
administrator).
Field
Description
Valid Values
User Name
Identifies the user to the network.
70 characters maximum
Password
Characters that gain access to network along
with the user name.
No character limitation
Domain Name
Provided by network administrator.
15 characters maximum
Using Configuration Mode
Diagnostic Setup
4-15
The Diagnostic Setup screen configures diagnostics for the current
computer. The screen shows a treeview of possible diagnostic nodes.
Terminal Settings
To access the Remote
Log Setup or Message
Routing, select the node
and then the Edit button.
Diagnostic Setup
The Remote Log Destination forwards messages that it receives to a
Windows 2000/XP computer running diagnostics. The location is
determined by the IP address and port number.
Field
Description
Valid Values
Address
Address of the remote Windows 2000/XP
computer.
xxx.xxx.xxx.xxx
Port
The port used to communicate with the
remote Windows 2000/XP computer.
4445 (default)
Message Routing
The Message Routing screen lets you access the following screens:
• Remote Log
• RSView Diagnostics List
Each one of the above screens shows a list of messages that can be
sent to that destination. The list shows the On/Off status of each
message type. Use the On/Off button to turn a message type on or
off. A message type is enabled if it has a checked box.
Publication 2711P-UM001C-EN-P
4-16
Using Configuration Mode
File Management
Terminal Settings
File Management
Delete Files
The File Management screen lets you access screens to:
• Delete Files
• Copy Files
Delete Files
From the Delete Files screen you can select options to:
• Delete Applications - deletes an .MER application file from a
storage location.
• Delete Fonts - deletes a font file from a storage location.
• Delete Log Files - deletes any data log files, alarm history files
and alarm status files in the System Default location on the
PanelView Plus terminal.
Delete Application or Font Files
The process for deleting an application file or a font file is the same.
1. Select the Source button to select the storage location of the
application or font file that you want to delete.
• Internal Storage - the Internal Compact Flash in the PanelView
Plus terminal.
• External Storage 1 - the External Compact Flash card loaded in
the card slot of the terminal.
• External Storage 2 - for future use.
2. Select a file from the list.
3. Select the Delete button.
4. You will be asked if you want to delete the selected application
or font file from the storage location. Select Yes or No.
Publication 2711P-UM001C-EN-P
Using Configuration Mode
4-17
Delete Log Files
Select this option to delete any data log files, alarm history files and
alarm status files in the System Default location on the PanelView Plus
terminal. You will be asked to confirm the operation.
Do you want to delete all of the RSView ME Station Log Files?
Select Yes or No. Any log files not located in the System Default
location will not be deleted.
Terminal Settings
Copy Files
File Management
From the Copy Files screen, you can select options to:
• Copy Applications - copies an .MER application file from one
storage location to another
• Copy Fonts - copies a font file from one storage location to
another.
Copy Files
Copy Applications or Fonts
The process for copying an application file or a font file is the same.
List of files stored
in Compact Flash
of terminal.
1. Select the Source button to select the location of the application
or font file that you want to copy.
• Internal Storage - the Internal Compact Flash in the PanelView
Plus terminal.
• External Storage 1 - the External Compact Flash card loaded in
the card slot of the terminal.
• External Storage 2 - for future use.
Publication 2711P-UM001C-EN-P
4-18
Using Configuration Mode
2. Select the Destination button on the same screen to open the
following screen.
3. Select the Destination button to select the storage location
where you want to copy the application or font file to.
• Internal Storage - the Internal Compact Flash in the PanelView
Plus terminal.
• External Storage 1 - the External Compact Flash card loaded in
the card slot of the terminal.
• External Storage 2 - for future use.
4. Select the Copy button to copy the selected application or font
file to the selected destination.
If the file exists, you will receive a warning and will be asked if
you want to overwrite the existing application.
5. Select Yes or No.
TIP
Publication 2711P-UM001C-EN-P
RSView looks for .MER files in the
\RockwellSoftware\RSViewME\Runtime folder
and font files in the
\RockwellSoftware\RSViewME\Fonts\ folder.
Using Configuration Mode
Display
4-19
The Display screen lets you open screens to access:
• Display Contrast
• Display Intensity
• Display Temperature
• Screen Saver
• Cursor
Terminal Settings
Display Contrast
Display Contrast
The Display Contrast screen lets you view and modify the current
contrast setting of the PanelView Plus 400 - 600 grayscale displays.
The numeric display shows the current contrast level as a percentage.
The change is not permanent until you select OK.
Terminal Settings
Display Intensity
Display
Display
Display Intensity
The Display Intensity screen lets you view or modify the current
intensity of the backlight. The default intensity is 100%. When you
change the intensity, the terminal temporarily changes to that
intensity. The change is not permanent until you select OK.
The Startup Intensity button toggles between Runtime and Default. If
Runtime is selected, the terminal startup screens will use the runtime
intensity setting selected on the above screen. If Default is selected,
the terminal startup screens will use the terminal default setting,
which is near 100%.
TIP
Displays are shipped with the contrast level set at
50% which is the optimum setting.
Publication 2711P-UM001C-EN-P
4-20
Using Configuration Mode
Display Temperature
Terminal Settings
Display
The Display Temperature screen shows the current temperature of the
display.
Display Temperature
Terminal Settings
Display
Screen Saver
Screen Saver
The Screen Saver screen lets you:
• disable the screen saver
• enable the screen saver after the selected idle time
• adjust the brightness intensity of the screen saver
• enable/disable the screen saver bitmap
Select Up or Down
Cursor button to
increase or decrease
the screen saver
brightness
Publication 2711P-UM001C-EN-P
Using Configuration Mode
4-21
Cursor
Terminal Settings
Display
The Cursor screen enables/disables the on-screen cursor.
Cursor
Font Linking
Font linking allows you to run a translated application on the terminal
by linking a font file to the base font (for example, linking a Chinese
font file to the base font Arial).
Terminal Settings
For more details on pre-installed terminal fonts and additional fonts
available for downloading, see Appendix C.
Font Linking
Select Base Font
Arial
Courier New
Tahoma
Times New Roman
List of fonts loaded on
the terminal.
Show Links
[F1]
Shows all fonts loaded on the terminal except the
base font. Select the name of the font you are
linking to the base font. Click the Add Fonts button
to link the font file for the selected font to the base
font. You will return to the Linked Fonts screen.
Close
[F8]
Linked Font
Add Linked Font
Courier New
MS Mincho
Tahoma
Times New Roman
Shows the location and name of the
font that is linked to the base font
used by the terminal. If a file is not
linked, box will be empty.
Add Fonts
[F1]
Close
[F8]
Base font = Arial
Link:
MS Mincho
External storage 1\MSMINCHO.TTC
Delete Link
[F1]
Deletes linked
font file (if any)
Edit Link
[F2]
Close
[F8]
Edits the link by allowing you to add the
linked file to a font loaded on the terminal.
Publication 2711P-UM001C-EN-P
4-22
Using Configuration Mode
Input Devices
The Input Devices screen lets you access screens to view and modify
settings for:
• Keyboard
• Keypad
• Mouse
• Touch Screen
Keyboard and Keypad Setup
Terminal Settings
The Keyboard and Keypad screen opens these screens:
• Key Repeat Settings
• Keypad Settings
Input Devices
Key Repeat Settings for Attached Keyboard or PanelView Plus Keypad
Keyboard or Keypad
The Key Repeat Settings configures settings for keys on the PanelView
Plus terminal or keys an attached keyboard.
Field
Description
Valid Values
Repeat Rate
The number of times a key is repeated per
second when you hold down a key.
Keypad: 0, 2 - 30
Keyboard: Device dependent
0, 2 - 30 is typical
Repeat Delay
The amount of time that elapses before a key
is repeated.
200 ms
400 ms
600 ms
1 sec
1.5 sec
2 sec
2.5 sec
Values are device dependent.
An unsupported value is
disabled (grayed).
Publication 2711P-UM001C-EN-P
Using Configuration Mode
4-23
Key Settings for PanelView Plus Keypad
The Keypad Settings screen enables/disables Single Key Mode option
which is used to restrict multiple or simultaneous key presses.
Field
Single Key Mode
Description
Valid Values
Enables or disables Single Key Mode.
Enabled
Enabled with Abort
Disabled (default)
If enabled, any programmable key that is
pressed inhibits all keys until the
programmable key is pressed again. This
includes the Alt, Ctrl, Shift keys.
If enabled with abort, any secondary key
press will terminate the initial key press
immediately.
If disabled, there are no restrictions on key
presses.
Hold Off Time
IMPORTANT
The length of time to ignore multiple presses
of the same key.
400 ms (default)
The keypad cannot produce Home, End, Page Up or
Page Down when Single Key mode is enabled.
Publication 2711P-UM001C-EN-P
4-24
Using Configuration Mode
Terminal Settings
Input Devices
Touch Screen
Touch Screen
The Touch Screen lets you access the following screens:
• Calibration
• Cursor
• Double-Tap Sensitivity
Touch Screen Calibration
This screen calibrates the touch screen of the PanelView Plus terminal.
Touch the center of the target (+) each of the 4 times it appears. When
the calibration is complete, you will see the message:
"Tap the screen to register saved data. Wait for 30 seconds to
cancel saved data and keep the current settings."
Carefully press and briefly hold stylus on the center of the target.
Cursor
This screen enables or disables the cursor on touch screen terminals.
Disabling the touch screen cursor will not disable the mouse.
Publication 2711P-UM001C-EN-P
Using Configuration Mode
4-25
Double-Tap Sensitivity
This screen lets you set and test the sensitivity for both speed and
physical distance between touch screen presses.
• The Set button sets the sensitivity of touch screen presses.
• The Test button tests the sensitivity of touch screen presses. If
you double-tap the test button with the time set using the Set
button, the Test button will reverse it’s foreground and
background colors.
Terminal Settings
Input Devices
Mouse
Mouse
The Mouse screen sets and tests the sensitivity for both speed and
physical distance between mouse clicks. This process is identical to
that for setting Double-Tap sensitivity for the touch screen.
Publication 2711P-UM001C-EN-P
4-26
Using Configuration Mode
Print Setup
Terminal Settings
Print Setup
The Print Setup screen lets you access screens to configure print
options for:
• Displays
• Alarms
• Diagnostic messages.
Display, Alarm, and Diagnostic Print Setup
The general setup for printing displays, alarm messages and
diagnostics messages from an RSView .MER application is the same.
The Advanced Settings for each function are different.
Field
Description
Valid Values
PCL Printer
Type of printer to use.
Laser (default)
Inkjet
Port
Port to use for printing displays, alarm
messages, and diagnostic messages.
Network (default)
USB
Network Path
Network path of printer to use if the Port
selection is Network.
519 characters maximum
Advanced Settings
Press this button to open additional settings.
Advanced Settings for Display Print Setup
Select the Advanced Settings button to:
• change print orientation (portrait or landscape)
• enable or disable draft mode
Publication 2711P-UM001C-EN-P
Using Configuration Mode
4-27
Advanced Settings for Diagnostic Messages and Alarm Messages
The following screen configures when to print diagnostic or alarm
messages that are sent to the Network or USB port.
To configure how messages are queued for printing, select the Print
Messages After button and set one of the following options:
• Specified number of messages
Prints messages after 60 are queued or another specified value.
The default is 60 (about one full page of messages.)
• 500 messages or timeout period, whichever is first
Prints after 500 messages are queued or a specific time period
has elapsed, whichever comes first. The default time period is
168 hours (7 days). You can specify another value. For example,
if 350 messages are in the queue and 7 days have elapsed, the
350 messages will print.
• Specified number of messages or timeout period,
whichever is first
Prints after a specified number of messages are queued or a
specific time period has elapsed, whichever comes first.
The default number of messages to queue is 60. The default
timeout period is 168 hours (7 days). You can change both
values. For example, the number of messages is set to 75 and
the timeout period is set to 48 hours (2 day). If the queue has 75
messages after only 24 hours, these messages will print. If there
are only 15 messages in the queue at 48 hours, the 15 messages
will not print until the time period has elapsed.
Publication 2711P-UM001C-EN-P
4-28
Using Configuration Mode
Startup Options
Terminal Settings
The Startup Options screen accesses the following screens to modify:
• RSView ME Station Startup
• Startup Tests
RSView ME Station Startup
Startup Options
RSView ME Station Startup
The RSView Machine Station Startup screen specifies what action the
PanelView Plus terminal takes on startup:
• Do not start RSView ME Station
• Go to Configuration Mode
• Run the Current Application
This option is available only if an application is loaded.
RSView ME Station will start up based on shortcuts in the Windows
Startup folder and whether an application is loaded.
Select the On Startup button to switch between Do not start RSView
ME, Go to Configure Mode, or Run the Current Application. Select the
button under the last two options to configure specific settings for
each mode.
Publication 2711P-UM001C-EN-P
Using Configuration Mode
4-29
Configuration Mode
The Configuration Mode Options screen specifies whether the
PanelView Plus will boot up in Configure Mode:
• with the current application loaded.
• with the communication configuration of the current application
or the terminal’s RSLinx communication configuration.
If you select Yes to replace the terminal’s communication
configuration with that of the application, any changes made to
the device addresses or driver properties in the RSLinx
Communications screen will be lost.
These options are available only if an application is loaded in the
terminal. If an application is not loaded, both options are disabled and
set to No.
Run Options
Configuration Mode
Run Options
The Run Options screen specifies whether or not:
• to replace the terminal’s communication (RSLinx) settings with
application settings when the application is run.
If you select Yes, any changes to the device addresses or driver
properties in the RSLinx Communications screen will be lost
when the terminal boots up.
• to delete log files (data, alarm history, alarm status) generated by
the terminal from the System Default location before running the
application.
Publication 2711P-UM001C-EN-P
4-30
Using Configuration Mode
Terminal Settings
Startup Options
Startup Tests
Startup Tests
The PanelView Plus can run extended tests on startup. The Startup
Tests screen provides access to these screens:
• Startup Tests Settings
• Repeat Count
IMPORTANT
Startup Tests apply only to PanelView Plus 700 1500 terminals.
Select Tests
The Select Tests screen shows a list of each test that can be performed
on the PanelView Plus terminal at startup and its current On/Off
status. You can turn any test in the list on or off by selecting the
On/Off button. The terminal will only run tests with a checked box.
Publication 2711P-UM001C-EN-P
Using Configuration Mode
4-31
Startup Tests Settings
From the Startup Tests Settings screen, you can:
• enable extended diagnostics to run on the terminal at startup
• disable extended diagnostics at startup
• specify how many times to repeat the selected tests that are run
on the terminal during startup.
The Repeat Count field shows the current value. You can enter a value
in the range of 0 - 128.
IMPORTANT
Enabling Extended Diagnostics and setting a high
Repeat Count will increase the time it takes the
terminal to reboot.
The tests will run each time you reset or cycle power
to the terminal until you disable Extended
Diagnostics. Setting a low repeat count will also
decrease the startup time.
Publication 2711P-UM001C-EN-P
4-32
Using Configuration Mode
System Event Log
The System Event Log screen displays a list of system events currently
logged by the PanelView Plus terminal.
Terminal Settings
System Event Log
• To display System Event Log Details for a specific event, select
an event and then select the More Details button.
• To clear all System Event Logs, press the Clear All button.
Publication 2711P-UM001C-EN-P
Using Configuration Mode
System Information
4-33
The System Information screen lets you access:
• RSView ME Station information
• Terminal Information
Terminal Settings
Terminal Information
System Information
The Terminal Information screen displays the following details for the
PanelView Plus terminal:
• total power on time
• processor temperature
• battery voltage and battery state
• amount of memory on terminal
Terminal Information
All fields are read only except for memory allocation. To access details
on Memory Allocation, select the Memory Allocation button.
Battery State
Battery State
400-600
700-1500
Good
Good battery condition
Good battery condition
Failing
Does not have a replaceable
battery. Replace terminal.
Low battery. Replace battery.
Bad
N/A
Battery is missing or bad.
Replace battery.
Battery Voltage
For PanelView Plus 400-600 terminals, the Battery Voltage field
indicates the battery state only.
Processor Temperature
For the 400-600 terminals, the Processor Temperature shows the
temperature of the display.
Publication 2711P-UM001C-EN-P
4-34
Using Configuration Mode
Memory Allocation
The Memory Allocation screen displays:
• amount of allocated storage or program memory
• amount of storage or program memory currently in use
You can modify the allocation of storage or program memory. Press
the Up or Down button to increase/decrease the memory allocation.
Each button press changes the allocation by a value of 4. If you
change the allocation for one type of memory, the other is
automatically updated accordingly.
TIP
Publication 2711P-UM001C-EN-P
These settings are not retained after a power cycle.
Values return to the default settings.
Using Configuration Mode
Terminal Settings
System Information
About RSView ME Station
4-35
RSView ME Station Information
The About RSView ME Station screen provides access to:
• RSView ME Station firmware number
• Rockwell Technical Support information
x.xx.xx.xx
Publication 2711P-UM001C-EN-P
4-36
Using Configuration Mode
Time/Date/Regional
Settings
Terminal Settings
Time/Date/Regional Settings
Date
Publication 2711P-UM001C-EN-P
The Time/Date/Regional Settings screen lets you access the following
screens to set:
• date
• regional settings
• time
• time zone
Date
The Date screen shows and configures the current date in separate
Year, Month and Day fields.
Field
Description
Valid Values
Year
The current year in a 4-digit format.
1980 - 2099
Month
The current month.
1 - 12
Day
The current day. The day of the month is
validated based on the month.
0 - 31
Using Configuration Mode
Terminal Settings
Time/Date/Regional Settings
Time
4-37
Time
The Time screen shows and configures the current time in 24-hour
format in separate Hour, Minute and Second fields.
Field
Description
Valid Values
Hour
The current hour in 24-hour format.
0 - 23
Minute
The current minute in 24-hour format.
0 - 59
Seconds
The current second in 24-hour format.
0 - 59
Publication 2711P-UM001C-EN-P
4-38
Using Configuration Mode
Terminal Settings
Time/Date/Regional Settings
Time Zone
Time Zone
The Time Zone screen shows the current time zone that is installed on
the PanelView Plus terminal. Time zones are installed as a part of the
operating system. Changing the time zone adjusts the current time and
date to match the new time zone.
Language
Default Time Zone
English
(GMT -05:00) Eastern Time (US & Canada)
French
(GMT +01:00) Brussels, Copenhagen, Madrid, Paris
German
(GMT +01:00) Amsterdam, Berlin, Bern, Rome, Stockholm, Vienna
Japanese
(GMT +09:00) Osaka, Sapporo, Tokyo
If the selected time zone supports Daylight Savings, you can select the
Daylight Savings button.
Daylight Savings
The Daylight Savings screen configures whether daylight savings time
is in effect for the current time zone. Daylight Savings is set to Yes for
all time zones except for Japanese, which does support daylight
savings. Daylight savings changes are not permanently applied until
you close the Time Zone screen.
Publication 2711P-UM001C-EN-P
Using Configuration Mode
Terminal Settings
Time/Date/Regional Settings
Regional Settings
4-39
Regional Settings
The Regional Settings screen allows you to access these screens:
• Language
• Numeric Format
• Long Date Format
• Short Date Format
• Time Format
The current language is shown at the bottom of the Regional Settings
screen.
Terminal Settings
Language
Time/Date/Regional Settings
The Language screen allows you to select a language that is installed
on the PanelView Plus. Languages are installed as a part of the
operating system.
Regional Settings
Language
Terminal Settings
Numeric Format screen
Time/Date/Regional Settings
The Numeric Format Screen allows you to modify the decimal
separator used by the current language. The default decimal separator
is ".". The field will accept a separator up to 3 characters.
Regional Settings
Numeric Format
Publication 2711P-UM001C-EN-P
4-40
Using Configuration Mode
Terminal Settings
Time/Date/Regional Settings
Regional Settings
Time Format
The Time Format screen configures the time format for the current
language. A sample of the current time is shown using the currently
selected format.
Time Format
Field
Description
Example
h:mm:ss tt (default)
h = hour, no leading zero
tt = AM or PM symbol
7:23:02 AM or 1:13:31 PM
11:43:59 AM
hh:mm:ss tt
hh = hour with leading zero
tt = AM or PM symbol
07:23:02 AM or 01:13:31 PM
11:43:59 PM
H:mm:ss
H = hour in 24 hour format, no leading zero
7:03:42 or 1:13:32
23:43:59
HH:mm:ss
HH = hour in 24-hour format with leading zero
07:03:42 or 01:13:22
23:43:59
AM Symbol
Characters to indicate AM. If the time format is
set to h:mm:ss tt or hh:mm:ss tt, you can modify
the AM symbol.
AM (default)
12 character maximum
PM Symbol
Characters to indicate PM. If the time format is
set to h:mm:ss tt or hh:mm:ss tt, you can modify
the PM symbol.
PM (default)
12 character maximum
Separator
Character(s) that separate fields in time format. : (default)
3 character maximum
Time Format
Publication 2711P-UM001C-EN-P
Using Configuration Mode
4-41
Terminal Settings
Short Date Format
Time/Date/Regional Settings
The Short Date Format screen configures the short date format used
by the current language. A sample of the current date is shown using
the currently selected short date format.
Regional Settings
Short Date Format
Field
Short Date Formats
Example
Format
M/d/yyyy (default)
M/d/yy
MM/dd/yy
MM/dd/yyyy
yy/MM/dd
yyyy-MM-dd
dd-MMM-yy
1/2/2003
1/2/03
01/02/03
01/02/2003
03/01/02
2003-01-02
02-Jan-03
Separator
Character(s) separator for fields in time format.
The default separator is either - or / depending
on short date format.
- or / (default)
3 character maximum
Publication 2711P-UM001C-EN-P
4-42
Using Configuration Mode
Terminal Settings
Long Date Format
Time/Date/Regional Settings
The Long Date Format screen configures the long date format used by
the current language. A sample of the current date is shown using the
currently selected long date format.
Regional Settings
Long Date Format
Field
Format
Publication 2711P-UM001C-EN-P
Short Date Formats
Example
dddd, MMMM, dd, yyyy (default)
dddd is name of week day
MMMM is name of month
dd is 2-digit day of month with leading zero
yyyy is 4-digit year
Monday, January 01, 2003
MMMM dd, yyyy
MMMM is name of month
dd is 2-digit day of month with leading zero
yyyy is 4-digit year
January 01, 2003
dddd, dd MMMM, yyyy
dddd is name of week day
dd is 2-digit day of month with leading zero
MMMM is name of month
yyyy is 4-digit year
Monday, 01 January, 2003
dd MMMM, yyyy
dd is 2-digit day of month with leading zero
MMMM is name of month
yyyy is 4-digit year
01 January, 2003
Chapter
5
Installing and Replacing Components
Chapter Objectives
This chapter shows how to install, replace or upgrade various
components of the PanelView Plus terminals. Most sections (except
for Communication Module, Product ID labels, Keypad Legend
Inserts, and the External Compact Flash Card) apply only to the 700 1500 terminals.
• Logic Module
• RAM and Internal Compact Flash
• Communication Module
• Display Module
• Battery
• Display Module Bezel
• Backlight
• AC Power Supply
• Product ID Label
• Keypad Legend Inserts
• External Compact Flash Card
Required Tools
Tools required to install or replace the various components of the
PanelView Plus terminal are:
• #1 and #2 Phillips screwdriver
• Electrostatic (ESD) wristband
Precautions
Before installing or replacing any components, disconnect power
from the PanelView Plus terminal. During installation, take care not to
touch any of the exposed electronic components.
ATTENTION
!
ATTENTION
!
1
Disconnect all power from the PanelView Plus
terminal before installing or replacing any
components. Failure to disconnect power may result
in electrical shock and/or damage to the terminal.
Work in a static free environment and wear a
properly grounded ESD wristband.
Be careful when touching any of the exposed
electronic components to prevent damage from
electrostatic discharge (ESD).
Publication 2711P-UM001C-EN-P
5-2
Installing and Replacing Components
Compatibility of Terminal
Components
When assembling components of a terminal or replacing the Internal
Compact Flash in a Logic Module, the components must be
compatible.
700 - 1500 Terminals Only
To verify compatibility of the Internal Compact Flash with the Logic
Module of PanelView Plus terminals, you must know what version of
RSView ME is running on the terminal.
1. Locate green label on back of unit to determine revision level of
your PanelView Plus terminal.
• Rev B: Contains RSView ME 3.0
• Rev C: Contains RSView ME 3.10
• Rev D: Contains RSView ME 3.20
2. Determine series of the Internal Compact Flash and Logic
Module.
For Revision D terminals running RSView ME 3.20, you cannot
use a Series C (or lower) Compact Flash Card running an earlier
version of RSView ME (3.10 or lower).
Once a terminal is upgraded to RSView ME 3.20, the Logic Module
and all contents within are compatible with RSView 3.20 devices.
RSView ME 3.0/3.10 .mer applications are compatible with RSView ME
3.20 terminals.
PanelView Plus Compatibility
The table below matches the correct series of the Internal Compact
Flash Card with the correct series of the Logic Module for the
PanelView Plus terminals. The Logic Module for PanelView Plus
terminals is available with or without memory pre-installed.
Terminal
Revision
Logic Module 2711P-RP
(without memory) is
compatible with:
Internal Compact Flash
2711P-RW1, 2, 3, 4
RSView ME
Version(1)
Rev B
Series A: 2711P-RP/A
Series B: 2711P-RWx/B
RSView ME 3.0
Rev C
Series B: 2711P-RP/B
Series C: 2711P-RWx/C
RSView ME 3.10
Series D: 2711P-RWx/D
RSView ME 3.20
Series D: 2711P-RWx/D
RSView ME 3.20
Rev D
(1)
Publication 2711P-UM001C-EN-P
Series C: 2711P-RP/C
When upgrading RSView ME 3.0 to 3.10 or higher, the Firmware Upgrade Kit is required.
Installing and Replacing Components
Installing RAM and Internal
Compact Flash
700 - 1500 Terminals Only
5-3
The Logic Module (2711P-RP, -RP1, -RP2, -RP3) of the PanelView Plus
is available with or without RAM/Internal Compact Flash pre-installed.
If RAM (2711P-RRxxx) and Internal Compact Flash (2711P-RWx) are
ordered as separate components, you must install the memory before
attaching the Logic Module to the Display Module.
To install/replace RAM and/or Internal Compact Flash:
1. Remove power from the terminal.
2. Place the terminal, display side down, on a flat stable surface.
3. Loosen the 6 captive screws that secure the Logic Module.
4. Carefully lift the Logic Module away from the terminal and turn
over to expose the circuit board.
IMPORTANT
Skip Steps 5 - 6 if not replacing RAM.
Wear a properly grounded ESD wristband
before touching any of the electronic
components in the Logic Module.
5. Locate the RAM module on the circuit board. Pull the metal
retaining clips away from the module and slide out the RAM
module (if present).
Compact Flash Card
Retaining Screw
RAM Module
Retaining
Clips
Skip Steps 7 - 11 if not replacing Internal
Compact Flash.
6. Insert the new RAM module at a 45° angle and snap down.
7. Locate the Internal Compact Flash card. Unscrew and remove
the retaining clip that secures the card.
8. Pull out the Compact Flash card (if present).
9. Insert the new Compact Flash card.
10. Re-attach retaining clip.
11. Attach the Logic Module by aligning the 2 connectors on the
bottom of the module with the connectors on the Display
Module.
12. Push down on the Logic Module until firmly seated.
13. Tighten the 6 captive screws that secure the Logic Module to a
torque of .68 N•m (6-8 in-lb).
Publication 2711P-UM001C-EN-P
5-4
Installing and Replacing Components
Installing and Replacing
the Logic Module
700 - 1500 Terminals Only
This section shows how to install and replace the Logic Module
(2711P-RP, RP1, -RP2, -RP3) of the PanelView Plus terminal. If the
Display Module and Logic Module are ordered as separate
components, attach the Logic Module to the Display Module before
panel installation.
The Logic Module is available with or without RAM (2711P-RRxxx)
and Internal Compact Flash (2711P-RWx ) pre-installed. If ordered as
separate components, you must install the memory before attaching
the Logic Module to the Display Module.
To install a Logic Module:
1. Disconnect power from the terminal.
2. If the Display Module is removed from panel, set the module,
display side down, on a clean, flat, stable surface to prevent
scratches.
3. Position the Logic Module over the back of the Display Module
until the 2 connectors on the bottom of the Logic Module align
with the connectors on the Display Module.
Captive
Screw
4. Push down on the Logic Module until firmly seated.
5. Tighten the 6 captive screws that secure the Logic Module to the
Display Module to a torque of .68 N•m (6-8 in-lb).
Logic Module
Captive screws
on top and bottom
Publication 2711P-UM001C-EN-P
Installing and Replacing Components
5-5
To replace the Logic Module:
Before replacing the Logic Module, you must remove the
Communication Module (if attached). You will also need to remove
the Internal RAM and Compact Flash from the Logic Module to reuse
in the new Logic Module.
1. Disconnect power from the terminal.
2. Disconnect all power and communication cables.
3. If Display Module is removed from panel, set the module,
display side down, on a clean, flat, stable surface to prevent
scratches.
4. Remove the 4 screws that attach the Communication Module (if
attached) to the Logic Module. Carefully lift the Communication
Module away from the Logic Module.
Communication Module
Screw
Logic Module
Captive Screw
Display Module
5. Loosen the 6 captive screws that secure the Logic Module to the
Display Module.
6. Carefully lift the Logic Module away from the back of the
Display Module.
7. Remove the internal RAM and Compact Flash from the Logic
Module if you want to reuse them in the future. Refer to page
5-3.
IMPORTANT
Wear a properly grounded ESD wristband
before touching any of the electronic
components in the Logic Module.
8. Install the new Logic Module as described on page 5-4.
9. Attach the Communication Module (if necessary).
Publication 2711P-UM001C-EN-P
5-6
Installing and Replacing Components
Installing/Replacing a
Communication Module
This section shows how to install and replace a Communication
Module on the PanelView Plus terminal. The Communication Module
installs over the Logic Module. The Communication Modules are
available as separate catalog numbers for specific communication
protocols. The installation is the same for all modules regardless of the
communication type.
WARNING
!
If you connect or disconnect any communication
cable with power applied to this module or any
device on the network, an electrical arc can occur.
This could cause an explosion in hazardous location
installations. Be sure that power is removed or the
area is nonhazardous before proceeding.
Installation for 700 - 1500 Terminals
TIP
The Logic Module must be attached to the Display
Module before you attach the Communication
Module.
To install a Communication Module:
1. Disconnect power from the terminal.
2. If Display Module is removed from panel, set the module,
display side down, on a clean, flat, stable surface to prevent
scratches.
3. Remove the label covering the Communication Module
connector on the Logic Module.
Logic Module
REMOVE LABEL TO INSTALL
COMMUNICATION MODULE
Publication 2711P-UM001C-EN-P
Installing and Replacing Components
5-7
4. Position the Communication Module over the Logic Module so
that the connectors on bottom of module align with connectors
on Logic Module.
5. To prevent Electrostatic Discharge (ESD) between the modules,
allow the Communication Module to touch the Logic Module
before making connection.
Communication
Module
Connector
Logic Module
6. Push down on Communication Module until connectors are
firmly seated.
7. Tighten the 4 screws that secure the Communication Module to
the Logic Module. Tighten screws to a torque of .68 N•m (6-8
in-lb).
Attached
Communication Module
Screw
To replace a Communication Module:
1. Disconnect power from the terminal.
2. Disconnect communication cables from the Communication
Module.
3. Remove the 4 screws that secure the Communication Module to
the Logic Module.
4. Carefully lift the Communication Module away from the Logic
Module and set aside.
5. Follow steps 4 - 7 above.
Publication 2711P-UM001C-EN-P
5-8
Installing and Replacing Components
Installation for 400 -600 Terminals
To install a communication module:
1. Disconnect power from the terminal.
2. Set the terminal, display side down, on a clean, flat, stable
surface.
3. Remove the label covering the connectors on the base unit of
the terminal.
REMOVE LABEL TO INSTALL
COMMUNICATION MODULE
4. Position the Communication Module over back of the terminal
so that the connector on bottom of Communication Module
align with the connector on the base unit.
Tighten this
screw first.
Captive
Screws
5. Push down on the Communication Module until connector is
firmly seated.
6. Tighten the three captive screws that secure the module to the
terminal, starting with the bottom, left screw on the module.
Tighten screws to a torque of .34 - .45 N•m (3 - 4 in-lb).
Publication 2711P-UM001C-EN-P
Installing and Replacing Components
5-9
To replace a Communication module:
1. Disconnect power from the terminal.
2. Disconnect communication cables from the Communication
Module.
3. Loosen the 3 screws that secure the Communication Module to
the terminal.
4. Carefully lift the Communication Module away from the terminal
and set aside.
5. Follow installation steps 4 - 6 on previous page.
Publication 2711P-UM001C-EN-P
5-10
Installing and Replacing Components
Replacing the Display
Module
This sections shows how to replace the Display Module
(2711P-RDxxxx). It is necessary to remove the Communication
Module from the Logic Module to perform this operation.
700 - 1500 Terminals Only
Communication Module
Logic Module
Display
Module
1. Disconnect power from the terminal.
2. Remove terminal from panel.
3. Detach the Communication Module (if attached) from the Logic
Module by removing the 4 screws.
4. Loosen the 6 captive screws that attach the Logic Module to the
Display Module.
Logic Module
Captive screws
on top and bottom
5. Carefully lift the Logic Module from the terminal.
6. Set the Display Module aside.
Publication 2711P-UM001C-EN-P
Installing and Replacing Components
5-11
7. Position the new Logic Module over the new Display Module so
that the connectors align.
8. Push down on the Logic Module until firmly seated.
9. Tighten the 6 captive screws that secure the Logic Module to the
Display Module to a torque of .68 N•m (6-8 in-lb).
10. Attach the Communication Module (if necessary) and tighten the
4 screws to a torque of .68 N•m (6-8 in-lb).
Publication 2711P-UM001C-EN-P
5-12
Installing and Replacing Components
Replacing the Battery
700 - 1500 Terminals Only
The lithium battery (2711P-RY2032) is used by the real-time clock and
static RAM; it is not used for application backup or retention. The
clock module has a life expectancy of 2 years without power.
WARNING
!
When you connect or disconnect the battery an
electrical arc can occur. This could cause an
explosion in hazardous location installations. Be sure
that power is removed and the area is nonhazardous
before proceeding. Replace the battery only with the
indicated catalog number.
For Safety information on the handling of lithium
batteries, including handling and disposal of leaking
batteries, see Guidelines for Handling Lithium
Batteries, publication AG 5-4.
Do not dispose of battery in a fire or incinerator.
Dispose of used batteries in accordance with local
regulations.
Store batteries in a cool, dry environment. We
recommend 25 °C with 40…60% relative humidity.
You may store batteries for up to 30 days between
-45…85 °C, such as during transportation. To avoid
possible leakage, do not store batteries above 60 °C
for more than 30 days.
To replace the battery:
1. Disconnect power from the terminal.
2. Place the terminal, display side down, on a flat stable surface.
3. Detach Communication Module (if attached) from the Logic
Module by removing the 4 screws.
4. Loosen the 6 captive screws that attach the Logic Module to the
Display Module.
Logic Module
Captive screws
Publication 2711P-UM001C-EN-P
Installing and Replacing Components
5-13
5. Carefully lift the Logic Module away from the terminal and flip
over to expose the circuit board.
IMPORTANT
Wear a properly grounded ESD wristband
before touching any of the electronic
components in the Logic Module.
6. Locate the battery on the circuit board.
Remove battery by lifting up the
edge indicated by arrow.
7. Remove the battery by lifting up the side of the battery.
8. Insert the new battery.
9. Attach the Logic Module by aligning the 2 connectors on the
bottom of the module align with the connectors on the terminal.
10. Push down on the Logic Module until firmly seated.
11. Tighten the 6 captive screws that secure the Logic Module to a
torque of .68 N•m (6-8 in-lb).
12. Attach the Communication Module (if necessary) and tighten the
4 screws to a torque of .68 N•m (6-8 in-lb).
Publication 2711P-UM001C-EN-P
5-14
Installing and Replacing Components
Replacing Bezel
Removing Display Module Bezel
700 - 1500 Terminals Only
It is not necessary to remove the Logic Module or Communication
Module before removing the bezel, except for the PanelView Plus 700.
1. Disconnect power from the terminal.
2. Set the terminal, display side down, on a flat stable surface.
IMPORTANT
Wear a properly grounded ESD wristband
before touching any of the electronic
components in the Logic Module.
3. Remove the screws from the back of the Display Module. The
number of screws varies for each terminal type.
Display Module Bezel
4. On touch screen terminals, remove the 2 screws that secure the
small metal plate to the back of the Display Module.
5. Disconnect the (touch screen) connector by pulling the tab
attached to the connector.
This step applies to Touch Screen only
terminals.
Plate
Touch Screen Connector
6. Remove the sealing gasket.
Sealing
Gasket
Publication 2711P-UM001C-EN-P
Installing and Replacing Components
5-15
7. Lift the back of the Display Module away from the bezel.
Work on a clean, flat, stable surface to protect the display from
debris, scratches and damage.
Display Module Bezel
8. Detach all connectors (maximum of 3). The number of
connectors varies by model.
• IrDa connector (if present)
• Function Key connector
• Touch Screen connector
9. Set bezel aside.
Replacing Display Module Bezel
1. Make sure new bezel is free of lint and marks before attaching.
2. Attach the following connectors. The number of connectors
varies by model.
• IrDa connector (if present)
• Function Key connector
3. Place the back of the Display Module over the new bezel. Be
careful not to pinch any of the cables.
Allow the Touch Screen connector to extend out of the access
opening.
4. Attach Touch Screen connector.
5. Replace the sealing gasket (shown in step 6 on page 5-14).
6. Attach screws that secure Display Module to bezel and tighten to
a torque of 1.35 - 1.58 N•m (12-14 in-lb).
7. On touch screen terminals, re-attach the small metal plate to the
back of the Display Module using 2 screws (shown in step 4 on
page 5-14).
Publication 2711P-UM001C-EN-P
5-16
Installing and Replacing Components
Replacing Backlight
700 - 1500 Terminals Only
This section shows how to replace the backlight for the 700, 1000, and
1250 models. The 1250 High-Bright and 1500 displays do not have a
replaceable backlight.
1. Disconnect power from the terminal.
2. Remove Display Module bezel as described on page 5-14.
3. Remove the 4 screws that secure the LCD Display.
4. Lift the LCD Display and detach the Display Connector from the
circuit board. The location of the connector varies by model.
Display
Connector
Publication 2711P-UM001C-EN-P
Installing and Replacing Components
5-17
5. Detach the Backlight Connector from the circuit board.
The 1250 has one or two Backlight Connectors.
Backlight
Connector
For PanelView Plus 700/1000
Work on a clean, flat, stable surface to protect the display from
debris, scratches and damage.
6. Press the retaining tab that secures the backlight and then pull
out the backlight.
Backlight
Retaining Tab
7. Insert the new backlight.
Backlight
Publication 2711P-UM001C-EN-P
5-18
Installing and Replacing Components
For PanelView Plus 1250
• The 1250 Series A and B displays have two backlights and use
Cat. No. 2711P-RL12C backlight replacement.
• The 1250 Series C displays have only one backlight and use Cat.
No. 2711P-RL12C2 backlight replacement.
Work on a clean, flat, stable surface to protect the display from
debris, scratches and damage.
8. Remove the screw(s) that secure the backlight(s) and then
remove the backlight(s). The two backlights for Series A and B
displays are each secured with 2 screws. The single backlight for
Series C displays are secured with 1 screw.
Backlights
Series A/B
9. Insert the new backlight(s) and then secure each with the same
screws from step 8.
10. Attach the LCD Display Connector to the circuit board (shown in
step 4 on page 5-16).
11. Attach the Backlight Connector to the circuit board (shown in
step 5 on page 5-17).
12. Secure the LCD Display by attaching the 4 screws. The terminals
use different size screws. Use the following chart to tighten the
screws.
PanelView Plus
Screw Size Torque
700
2.5 mm
.68 N•m (6-8 in-lb)
1000/1250
#4
.68 N•m (6-8 in-lb)
1500
#6
.90 - 1.1 N•m (8-10 in-lb)
13. Replace the Display Module bezel as described on 5-15.
Publication 2711P-UM001C-EN-P
Installing and Replacing Components
Installing the Remote AC
Power Supply
700 - 1500 Terminals Only
5-19
Connecting to AC power requires a separate Power Supply
(2711P-RSACDIN) that mounts to a DIN Rail. This power supply
converts AC power to DC power and has the following electrical input
ratings:
• 85…264 V AC (47…63 Hz)
For details on installation, refer to the installation instructions shipped
with the power supply.
Removing the Product ID
Label
If you ordered a PanelView Plus terminal with a label, you can
remove it and attach your own label.
1. Remove the Allen-Bradley label using your fingers or a tweezers.
2. Clean area with damp cloth and isopropyl alcohol.
3. Remove adhesive backing of OEM label and affix over area
where Allen-Bradley label was located.
Publication 2711P-UM001C-EN-P
5-20
Installing and Replacing Components
Installing Keypad Legend
Inserts
This section shows how to replace the legend inserts in the PanelView
Plus keypad terminals. The legend strips are available as separate
catalog numbers (2711P-RFKxx) for each keypad terminal, except for
the PanelView Plus 400 terminals (which does not support replaceable
legend strips). One side of the legend strips have the default key
legends and the other side is blank for creating custom legends.
PanelView Plus 600 Terminals
The legend inserts for function keys F1 - F10 are accessible from the
back on the unit and can be replaced with the terminal mounted in
the enclosure.
To replace the F1-F10 function key legends:
1. From the rear of the unit, pull the legend strips out from the
slots on the lower side of the terminal.
2. Slide the new insert into the same slot until only the end tab is
visible.
600 Terminals
Publication 2711P-UM001C-EN-P
Installing and Replacing Components
5-21
PanelView Plus 700-1500 Terminals
The F1-Fxx and K1-Kxx legend inserts on the PanelView Plus 700 1500 terminals are accessible when the Display Module bezel is
removed.
To replace the F1-Fxx or K1-Kxx function key legends:
1. Remove power from the terminal.
2. Remove the Display Module bezel as described on page 5-14.
3. Pull the legend inserts out from the slots on the bezel.
4. Insert the new legend strips into the same slots until only the
end tab is visible.
5. Replace the Display Module bezel as described page 5-15.
Using an External Compact
Flash Card
All of the PanelView Plus terminals have a Compact Flash Card slot
which supports Type I Compact Flash cards. These cards (2711P-RCx)
are available in different memory sizes.
The orientation of the card slot on the 700-1500 terminals varies
depending on the series of the Logic Module.
Compact Flash Card Slot
Publication 2711P-UM001C-EN-P
5-22
Installing and Replacing Components
Inserting a Compact Flash Card
1. Insert the card in the Compact Flash Card slot of the terminal
until firmly seated.
400 - 600 Terminals
700 - 1500 Terminals
Removing a Compact Flash Card
1. Press the Eject button on the Logic Module. When the button
pops out, press it again to release the card. The location of the
button varies depending on the series of the Logic Module.
The PanelView Plus 400 and 600 terminals do not have an eject
button. Simply secure edge of card with fingers and pull card
away from slot.
Publication 2711P-UM001C-EN-P
Chapter
6
Terminal Connections
Chapter Objectives
This chapter provides network and device connections for the
PanelView Plus terminals, including:
• wiring and safety guidelines
• Logic controller cable charts
• USB port(s)
• Serial connections on base unit
• Ethernet (onboard communications)
• DH485/DH+/RIO Communications Module
(one module for 700-1500 terminals; separate module with each
communication protocol for 400-600 terminals)
• ControlNet Communications Module (700 - 1500 only)
Wiring and Safety
Guidelines
Use publication NFPA 70E, "Electrical Safety Requirements for
Employee Workplaces", IEC 60364 "Electrical Installations in
Buildings" or other applicable wiring safety requirements for the
country of installation when wiring the VersaView CE terminals. In
addition to the NFPA guidelines:
• route communication cables to terminal by a separate path from
incoming power:
IMPORTANT
Do not run signal wiring and power wiring
in the same conduit.
• where power and communication lines must cross, they should
cross at right angles. Communication lines can be installed in the
same conduit as low level DC I/O lines (less than 10 volts).
• shield and ground cables appropriately to avoid Electromagnetic
Interference (EMI).Grounding minimizes noise from EMI and is
a safety measure in electrical installations.
A source for grounding recommendations is the National Electric Code
published by the National Fire Protection Association.
1
Publication 2711P-UM001C-EN-P
6-2
Terminal Connections
Logic Controller Cable
Charts
Refer to the following charts for a summary of PanelView Plus
terminal connections to controllers and network interface modules.
Runtime Communication Cables - To Controllers
Cables: PanelView Plus to SLC Controllers
Protocol
SLC-500, 5/01, 5/02
CH1 RJ45
(DH-485)
SLC-5/03, 5/04, 5/05
CH0 (9-pin RS-232)
(DF1 or DH-485)
SLC 5/03
CH1 (RJ45)
(DH-485)
SLC 5/04
CH1 (DH+)
SLC 5/05
CH1 (ENET)
N/A
2711-NC13 (16ft/5m)
2711-NC14 (32ft/10m)
2706-NC13 (10ft/3m)
N/A
N/A
N/A
use AIC+ Module
(1761-NET-AIC)
Connect to Port 1 or 2
2711-NC13 (16ft/5m)
2711-NC14 (32ft/10m)
2706-NC13 (10ft/3m)
use AIC+ Module
(1761-NET-AIC)
Connect to Port 1 or 2
N/A
N/A
DH-485 Communication Port
PanelView Plus 400 -600
2711P-xxx3xx, 2711P-RN3
1747-C10 (6ft/2m)
1747-C11 (0.3m/1ft)
1747-C20 (20ft/6m)
use AIC+ Module
(1761-NET-AIC)
Connect to Port 3
1747-C10 (6ft/2m)
1747-C11 (0.3m/1ft)
1747-C20 (20ft/6m)
N/A
N/A
DH-485 Communication Port
PanelView Plus 700 -1500
2711P-xxx6xx, 2711P-RN6
1761-CBL-AS03
(10ft/3m)
1761-CBL-AS09
(30ft/9m)
use AIC+ Module
(1761-NET-AIC)
Connect to Port 3
1761-CBL-AS03
(10ft/3m)
1761-CBL-AS09
(30ft/9m)
N/A
N/A
PanelView Plus Comm Port
DF1
(any)
RS-232 (DF1) Comm Port (9-pin)
PanelView Plus 400 -1500
2711P-RN22C
DH-485
(any)
RS-232 (DH-485) Comm Port (9-pin)
PanelView Plus 400 -1500
2711P-RN22C
ControlNet
xxx15xx
EtherNet/IP
(any except
xxx5xx)
ControlNet Communication Port
PanelView Plus 700-1500
2711P-xxx15xx, 2711P-RN15S
EtherNet/IP Comm Port
PanelView Plus 400 -1500
(except 2711P-xxx5xx)
Remote I/O
xxx1xx
xxx6xx
Remote I/O Communication Port
PanelView Plus 400 -1500
2711P-xxx1xx, -xxx6xx, 2711P-RN1, 2711P-RN6
DHPlus
xxx6xx
xxx8xx
DH+ Communication Port
PanelView Plus 400 -1500
2711P-xxx6xx, -xxx8xx, 2711P-RN6, 2711P-RN8
(1)
1747-KFC15A or
1747-SCRNR/A Module with ControlNet cable
N/A
Use 1761-NET-ENI Module
with Ethernet Cable
SLC 5/02 only
use 1747-SN with
shielded twinaxial cable
(1770-CD)
N/A
N/A
use 1747-SN Module with shielded twinaxial cable (1770-CD)
N/A
PanelView Plus EtherNet/IP direction connection to SLC 5/05 requires hub or crossover cable listed
Publication 2711P-UM001C-EN-P
N/A
2711PCBL-EX04
Ethernet
Crossover
Cable (1)
N/A
shielded
twin axial
cable
(1770-CD)
N/A
Terminal Connections
6-3
Cables: PanelView Plus to PLC-5 and MicroLogix Controllers
Protocol
PanelView Plus Comm Port
PLC-5, PLC-5C, PLC-5E
CH0 (25-pin RS-232)
(DF1)
MicroLogix 1500LRP
CH1 (9-pin RS-232)
(DF1 or DH-485)
MicroLogix 1000, 1200,
1500LSP
CH0 (8-pin Mini DIN)
(DF1 or DH-485)
2711-NC13 (16ft/5m)
2711-NC14 (32ft/10m)
2706-NC13 (10ft/3m)
(9-to-25 pin adapter required)
2711-NC13 (16ft/5m)
2711-NC14 (32ft/10m)
2706-NC13 (10ft/3m)
2711-NC21 (16ft/5m)
2711-NC22 (49ft/15m)
(null modem not required) (1)
DF1
(any)
RS-232 (DF1) Comm Port (9-pin)
PanelView Plus 400 -1500
2711P-RN22C
DH-485
(any)
RS-232 (DH-485) Comm Port (9-pin)
PanelView Plus 400 -1500
2711P-RN22C
N/A
2711-NC13 (16ft/5m)
2711-NC14 (32ft/10m)
2706-NC13 (10ft/3m)
2711-NC21 (16ft/5m)
2711-NC22 (49ft/15m)
(null modem not required) (1)
DH-485 Communication Port
PanelView Plus 400 -1500
2711P-xxx3xx, -xxx6xx, 2711P-RN3, 2711P-RN6
N/A
N/A
use AIC+ Module
(1761-NET-AIC)
Connect to Port 3
to PLC-5C with
ControlNet cable
N/A
N/A
ControlNet
xxx15xx
ControlNet Communication Port
PanelView Plus 700-1500
2711P-xxx15xx, 2711P-RN15S
EtherNet/IP
(any except
xx5xx)
EtherNet/IP Comm Port
PanelView Plus 400 -1500
(except 2711P-xxx5xx)
Remote I/O
xxx1xx
xxx6xx
Remote I/O Communication Port
PanelView Plus 400 -1500
2711P-xxx1xx, -xxx6xx, 2711P-RN1, 2711P-RN6
shielded twinaxial cable
(1770-CD)
DHPlus
xxx6xx
xxx8xx
DH+ Communication Port
PanelView Plus 400 -1500
2711P-xxx6xx, -xxx8xx, 2711P-RN6, 2711P-RN8
shielded twinaxial cable
(1770-CD)
(1)
to PLC-5E with
Ethernet cable
use 1761-NET-ENI Module
with Ethernet cable
N/A
N/A
N/A
N/A
AIC+ Module recommended for isolation purposes when PanelView and controller are not on same power supply
Cables: PanelView Plus to Logix Controllers
Protocol
DF1
(any)
DH-485
(any)
PanelView Plus Comm Port
ControlLogix
CH0 (9-pin RS-232)
(DF1)
RS-232 (DF1) Comm Port (9-pin)
PanelView Plus 400 -1500
2711P-RN22C
RS-232 (DH-485) Comm Port (9-pin)
PanelView Plus 400 -1500
2711P-RN22C
DH-485 Communication Port
PanelView Plus 400 -1500
2711P-xxx3xx, -xxx6xx, 2711P-RN3, 2711P-RN6
CompactLogix
CH0 (9-pin RS-232)
(DF1 or DH-485)
FlexLogix
CH0 (9-pin RS-232)
(DF1)
2711-NC13 (16ft/5m)
2711-NC14 (32ft/10m)
2706-NC13 (10ft/3m)
2711-NC13 (16ft/5m)
2711-NC14 (32ft/10m)
2706-NC13 (10ft/3m)
N/A
N/A
use AIC+ Module
(1761-NET-AIC)
Connect to Port 3
N/A
use 1756-CNB Module with
ControlNet cable
1769-L35C
with ControlNet cable
use 1788-CNC or 1788-CNF Module
with ControlNet cable
use 1756-ENET or 1756-ENBT
Module with
Ethernet cable
to 1769-L35E with Ethernet cable
use 1788-ENBT Module
with EtherNet cable
ControlNet
xxx15xx
ControlNet Communication Port
PanelView Plus 700-1500
2711P-xxx15xx, 2711P-RN15S
EtherNet/IP
(any except
xx5xx)
EtherNet/IP Comm Port
PanelView Plus 400 -1500
(except 2711P-xxx5xx)
Remote I/O
xxx1xx
xxx6xx
Remote I/O Communication Port
PanelView Plus 400 -1500
2711P-xxx1xx, -xxx6xx, 2711P-RN1, 2711P-RN6
use 1756-DHRIO Module
with
shielded twinaxial cable
(1770-CD)
N/A
N/A
DHPlus
xxx6xx
xxx8xx
DH+ Communication Port
PanelView Plus 400 -1500
2711P-xxx6xx, -xxx8xx, 2711P-RN6, 2711P-RN8
use 1756-DHRIO Module
with
shielded twinaxial cable
(1770-CD)
N/A
N/A
Publication 2711P-UM001C-EN-P
6-4
Terminal Connections
Cables: PanelView Plus to Communication Adapters
1761-NET-AIC
1747-AIC
Protocol
DF1 (any)
DH-485
(any)
(1)
PanelView Plus Comm Port
RS-232 Comm Port (9-pin)
PanelView Plus 400 -1500
2711P-RN22C
RS-232 Comm Port (9-pin)
PanelView Plus 400 -1500
2711P-RN22C
Port 2
8-pin Mini DIN()
Port 1 (9-pin)
N/A
N/A
2711-NC13 (16ft/5m)
2711-NC14 (32ft/10m)
2706-NC13 (10ft/3m)
2711-NC21 (16ft/5m)
2711-NC22 (49ft/15m)
2711-NC13 (16ft/5m)
2711-NC14 (32ft/10m)
2706-NC13 (10ft/3m)
2711-NC21 (16ft/5m)
2711-NC22 (49ft/15m)
DH-485 Communication Port
PanelView Plus 400 -600
2711P-xxx3xx, 2711P-RN3
1747-C10 (6ft/2m)
1747-C11 (0.3m/1ft)
1747-C20 (20ft/6m)
N/A
DH-485 Communication Port
PanelView Plus 700 -1500
2711P-xxx6xx, 2711P-RN6
Direct connection to
single AIC with
Belden 9842 cable(1)
N/A
Use serial port on terminal with an AIC+ module for a DH-485 network solution.
Publication 2711P-UM001C-EN-P
Port 3
(DH485)
1761-NETDNI
or 1771-NET-ENI
N/A
1761-CBL-AP00 (5m)
1761-CBL-PM02 (2m)
2711-CBL-PM05 (5m)
2711-CBL-PM10 (10m)
N/A
1761-CBL-AS03
(10ft/3m)
1761-CBL-AS09
(30ft/9m)
to single AIC+
Direct connection to
single AIC+ with
Belden 9842 cable(1)
N/A
N/A
Terminal Connections
USB Ports
6-5
The 700 - 1500 terminals have two USB ports. The 400 - 600 terminals
have one USB port. The terminals currently support standard USB
keyboard and mouse devices (that is, HID devices) with native device
drivers. They also support some USB printers that have Printer Control
Language (PCL) capabilities. A vendor specific Windows CE driver is
required for all other USB devices.
See Appendix B for a list of compatible USB devices.
The USB device can plug into either one of the two USB ports on the
PanelView Plus 700 - 1500 terminals.
USB Connector Pinout
400-600 USB Port
4
3
2
1
700-1500 USB Ports
4
3
2
1
4
3
2
1
Pin
Signal
1
USBVCC
2
USBD-
3
USBD+
4
USB-GND
WARNING
!
WARNING
!
If you connect or disconnect the USB cable with
power applied to the PanelView Plus or the serial
device on the other end of the cable, an electrical arc
can occur. This could cause an explosion in
hazardous location installations. Be sure that power
is removed or the area is nonhazardous before
proceeding.
USB devices not powered by the USB port must be
within the same enclosure and connected to a
ground system common with the terminal, or the
USB devices must be used with a USB hub that
provides galvanic isolation.
Publication 2711P-UM001C-EN-P
6-6
Terminal Connections
Serial Connections
The base configured unit of all PanelView Plus terminals have a
multi-purpose serial RS-232 port that supports:
• DH-485 communications through a serial connection
• DF1 full duplex communications with controllers using direct
connections or modem connections
• third party point-to-point communications
• application uploads/downloads
• printing
The serial port on the base configured unit of the PanelView Plus
terminal is a 9-pin, male, RS-232 connector. The table below shows
the pinout descriptions for this port and how these pins map to the
serial ports on the controllers.
Base Configured Unit 400-600
Base Configured Unit 700-1500
Serial RS-232 Port
1
6
5
9
Insert tie in hole and
use as strain relief for
all attached cables.
Serial RS-232 Port
PanelView Plus RS-232 Port
9-pin DCE
1
2
RXD
2
3
4
3
TXD
3
2
7
4
DTR
4
20
5
COM
5
7
6
DSR
6
6
7
RTS
7
4
8
CTS
8
5
9
Connector Shell
SLC
9-pin
PLC
25-pin
MicroLogix/
DNI 8-pin DIN
2
Chassis Gnd
Pins 1 - 9 are electrically isolated.
The maximum cable length for serial communications is 15.24 meters
(50 feet).
WARNING
!
Publication 2711P-UM001C-EN-P
If you connect or disconnect the serial cable with
power applied to the PanelView Plus or the serial
device on the other end of the cable, an electrical arc
can occur. This could cause an explosion in
hazardous location installations. Be sure that power
is removed or the area is nonhazardous before
proceeding.
Terminal Connections
6-7
Modem Connection
Wire or radio modem communications is possible between the
PanelView Plus and controller. Each modem must support full duplex
communications. Refer to your modem user manual for details on
settings and configuration.
PanelView Plus
Optical Isolator
DF1 Port
Controller
Modem
Modem
Constructing a Null Modem Cable
To construct a null modem cable, refer to the following pinout:
9-pin
25-pin
9-pin
3
3
3
2
2
2
5
7
5
1
8
1
4
20
4
6
6
6
8
5
8
7
4
7
Publication 2711P-UM001C-EN-P
6-8
Terminal Connections
Computer Connections
The RS-232 serial port on the base configured units of the PanelView
Plus terminals supports:
• application uploads/downloads using a direct connection
• or printing
Base Configured Unit of PanelView Plus
Computer
Available Cables
Cat. No. 2711-NC13, 5 m (16.4 ft)
Cat. No. 2711-NC14, 10 m (32.7 ft)
Cat. No. 2706-NC13, 3 m (10 ft)
25-pin to 9-pin
Adapter
(if required)
RS-232 Port
PanelView Plus Port (DCE)
9-pin male
1 NC
RXD
2
TXD
3
4 NC
COM
5
6 (pulled high to +12V)
RTS
7
CTS
8
9 NC
Computer Port (DTE)
with Handshaking
9-pin male
1 DCD
2 RXD (Data Receive)
3 TXD (Data Transmit)
4 DTR
5 COM
6 DSR
7 RTS
8 CTS
9 NC
Upload/Download Cable without Hardware Handshaking
PanelView Plus Printer Port (DCE)
9-pin male
2
3
5 COM
Publication 2711P-UM001C-EN-P
RXD
TXD
COM
Computer Port (DTE)
9-pin 25-pin
2
3
3
2
5
7
Terminal Connections
Ethernet Connections
6-9
The base configured unit of the PanelView Plus 700 - 1500 terminals
and the network based unit of the 400 - 600 terminals have an
Ethernet port that supports:
• EtherNet/IP communications
• third party Ethernet communications
• network connections
• application uploads/downloads
• printing
Ethernet Connector
The base configured units of the PanelView Plus terminals have an
RJ45, 10/100Base-T connector for EtherNet/IP or Ethernet TCP/IP
network communications.
Ethernet Port
Use RS-232 serial port to
transfer applications or print.
Insert tie in hole and
use as strain relief for
all attached cables.
The connector pinout is shown below.
Pin
Pin
RJ45
Connector
1
TD+
2
TD-
3
RD+
4
NC
5
NC
6
RD-
7
NC
8
NC
8
1
Shield Connection
Pin Name
Chassis Gnd
Use point-to-point, 10/100Base-T cables with cross over pin-outs
(such as 2711P-CBL-EX04) when connecting the Ethernet port on the
PanelView Plus directly to a logic controller’s Ethernet port or a
computer 10/100Base-T port. Use standard Ethernet cables when
connecting to a switch or hub.
Publication 2711P-UM001C-EN-P
6-10
Terminal Connections
Cables
Category 5 shielded and unshielded twisted-pair cables with RJ45
connectors are supported. If 100 Mbit/second data rates are used, we
recommend that you use a shielded cable. The shielded cable will
help insure that industrial noise immunity levels are maintained. The
maximum cable length between the terminal’s Ethernet port and a
10/100Base-T port on an Ethernet hub (without repeaters or fiber) is
100 meters (328 feet). In industrial applications, keep the cable length
to a minimum.
WARNING
!
If you connect or disconnect the Ethernet cable with
power applied to the PanelView Plus or any device
on the network, an electrical arc can occur. This
could cause an explosion in hazardous location
installations. Be sure that power is removed or the
area is nonhazardous before proceeding.
Security Considerations
IGMP (Internet Group Management Protocol) is used for IPv4
multicast. A multicast is communication between a single sender and
multiple receivers on a network. IGMP is used to exchange
membership status data between IPv4 routers that support
multicasting and members of multicast groups. A router is an
intermediary device on a communication network that expedites
message delivery by finding the most efficient route for a message
packet within a network, or by routing packets from one sub-network
to another. A sub-network is a separate part of an organization’s
network identified through IP addressing.
PanelView Plus terminals provide level 2 (full) support for IPv4
multicasting (IGMP version 2) as described in RFC 1112 and RFC 2236.
Note: SNMP (Simple Network Management Protocol) is used for
internal network management and is not supported.
Ports 137 and 138 are normally open to support the NetBIOS protocol
used by Windows CE.NET similar to other Microsoft and IBM network
operating systems.
Publication 2711P-UM001C-EN-P
Terminal Connections
DH-485/DH+/Remote I/O
Module
6-11
PanelView Plus terminals with a DH-485/DH+/Remote I/O
Communication Module supports communication with the following
networks:
• DH+ networks
• DH-485 networks
• Remote I/O networks
You can communicate with only one network at one time.
The PanelView Plus 700-1500 terminals support all protocols on one
module. The PanelView Plus 400 and 600 terminals require a separate
module for each protocol. The DH+, DH-485 and Remote I/O
connections are different between the modules for the PanelView Plus
400-600 and 700-1500 terminals.
Module Connections
See your controller documentation for appropriate
controller connections.
IMPORTANT
400 - 600 Terminals
700 - 1500 Terminals
DH-485 Comm Module
Allen
Bradley
DH485
1
2
3
4
5
6
DH+
RIO
3
2
1
Pin 8
Pin 1
1. Earth Ground
2. Shield/Drain
3. Signal Ground
4. Channel B
5. Channel A
6. Termination Resistance
Remote I/O
DH+
3. Clear
2. Shield/Drain
1. Blue
3. Blue
2. Shield/Drain
1. Clear
LED Indicator
Pin 8
Comm. Connector
Programming
Connector
1. Data_H
2. Data_L
DH-485 Module is
3. +24V DC Enable
electrically isolated
4. Power 1
from Network.
5. TX Enable
6. Shield
7. Ground
8. Power 2
DH+ Comm Module
1 2 3
Blue
Shield
Clear
Remote I/O (Single Rack) Comm Module
1 2 3
Blue
Shield
Clear
Publication 2711P-UM001C-EN-P
6-12
Terminal Connections
DH-485 Network Port Wiring (700 - 1500 only)
Use these instructions for wiring Belden cable. If you are using
standard Allen-Bradley cables, see the Cable section on page 6-2.
Attaching RS-485 Connector to the Communication Cable
A daisy-chained network is recommended. We do
not recommend hybrid star/daisy chain networks as
shown below.
IMPORTANT
Belden
#3106A or
#9842
Belden
#3106A or
#9842
Belden
#3106A or
#9842
Connector
Connector
Connector
Incorrect
Attach the connector to the Belden #3106A or #9842 Cable as shown
below.
Single Cable Connection
6
5
4
3
2
1
Orange with White Stripes
White with Orange Stripes
Shrink Tubing
Recommended
Terminal
A
B
Common
Shield
Chassis Ground
Blue (#3106A) or
Drain Wire
Blue with White Stripes (#9842)
to Previous Device
Multiple Cable Connection
to Successive Device
The table below shows connections for Belden #3106A.
Publication 2711P-UM001C-EN-P
For this Wire/Pair
Connect this Wire
To this Terminal
Shield/Drain
Non-jacketed
Terminal 2 - Shield
Blue
Blue
Terminal 3 - (Common)
White/Orange
White with Orange Stripe
Terminal 4 - (Data B)
Orange with White Stripe
Terminal 5 - (Data A)
Terminal Connections
6-13
DH-485 Connections (400 - 600 only)
This section shows connections between a PanelView 400-600
terminal with a DH-485 Communication Module and an SLC or
ControlLogix controller through the AIC+ module.
PanelView Plus 400-600
with DH-485 Module
AIC +
1784-CP14 Cable
1761-CBL-PM002 Cable
RS-232
To ControlLogix or SLC Controller
Publication 2711P-UM001C-EN-P
6-14
Terminal Connections
DHPlus Network Connections
Use the Belden 9463 twin axial cable (1770-CD) to connect a
PanelView Plus terminal to the DH+ link.
You can connect a DH+ link in 2 ways:
• trunk line/drop line - from the drop line to the connector screw
terminals on the DH+ connectors of the processor
• daisy chain - to the connector screw terminals on the DH+
connectors on the processor
Follow these guidelines when installing DH+ communication links:
• do not exceed these cable lengths:
– trunk line-cable length: 3,048 m (10,000 ft)
– drop-cable length: 30.4 m (100 ft)
The maximum cable length is determined by baud rate.
• do not connect more than 64 stations on a single DH+ link
PanelView Plus 700-1500
DH+ Port on Communication Module
Belden
To Controller
Blue 3
Shield SH 2
Clear 1
• 82 Ω terminating resistor for 230.4K
bits/sec
• 150 Ω terminating resistor for 230.4K
and 115.2K bits/sec
PanelView Plus 400-600
DH+ Port on Communication Module
Belden
To Controller
Publication 2711P-UM001C-EN-P
Blue 3
Shield SH 2
Clear 1
• 82 Ω terminating resistor for 230.4K
bits/sec
• 150 Ω terminating resistor for 230.4K
and 115.2K bits/sec
Terminal Connections
6-15
Remote I/O Connections
To connect a PanelView Plus terminal to a Remote I/O scanner, use
cable Catalog No. 1770-CD (equivalent to Belden 9463). The
maximum cable length (link distance) is determined by the baud rate.
• 2,800 meters (10,000 feet) for 57.6K baud
• 1,400 meters (5,000 feet) for 115.2K baud
• 700 meters (2,500 feet) for 230.4K
See Programmable Controller Wiring and Grounding Guidelines,
Publication 1770-4.1. The user manual for the I/O scanner module
also provides cabling information.
PanelView Plus 700-1500
Remote I/O Port on Communication Module
Belden
To Controller
Clear 3
Shield SH 2
Blue 1
• 82 Ω terminating resistor for 230.4K
bits/sec
• 150 Ω terminating resistor for 230.4K
and 115.2K bits/sec
PanelView Plus 400-600
Remote I/O Port on Communication Module
Belden
To Controller
Blue 3
Shield SH 2
Clear 1
• 82 Ω terminating resistor for 230.4K
bits/sec
• 150 Ω terminating resistor for 230.4K
and 115.2K bits/sec
Publication 2711P-UM001C-EN-P
6-16
Terminal Connections
ControlNet Module
PanelView Plus 700-1500 terminals with a ControlNet Communication
Module support communications and the transfer of applications
between devices on a ControlNet network.
Related Information
For more information on ControlNet products, refer to the following
publications.
• ControlNet System Overview (Publication 1786-2.9)
• ControlNet System Planning and Installation Manual (1786-6.2.1)
• ControlNet Cable System Component List (AG-2.2)
The Allen-Bradley website (www.rockwellautomation.com) provides
information and product descriptions of ControlNet products. Under
the Products and Services heading, select Communications.
ControlNet Protocol
The PanelView Plus terminals support release 1.5 of ControlNet.
Unscheduled PLC-5C and ControlLogix messaging and redundant
cabling is supported.
ControlNet allows a flexible control architecture that can work with
multiple processors and up to 99 nodes (via taps) anywhere along the
trunk cable of the network. There is no minimum tap separation and
you can access the ControlNet network from every node (including
adapters).
Publication 2711P-UM001C-EN-P
Terminal Connections
6-17
Compatible ControlNet Controllers
A PanelView Plus terminal with a ControlNet Module communicates
with a PLC-5C (using PCCC commands) or a ControlLogix processor
(using CIP protocol) using unscheduled messaging. The following
controllers are supported:
• ControlLogix using 1756-CNB module
• PLC-5/20C, -5/40C, -5/60C, -5/80C
ControlNet Connections (700 - 1500 only)
Use the pinout information below to connect the PanelView Plus to a
ControlNet network.
LED Indicator
Pin 1
NAP Connector
A
Channel A
Channel B
Redundant BNC
Cable Connectors
Pin
1
2
3
4
5
6
7
8
Shell
NAP Signal
Signal Common
No Connection
TX_H
TX_L
RX_L
RX_H
No Connection
Signal Common
Earth Ground
B
Allen Bradley
ControlNet
Publication 2711P-UM001C-EN-P
6-18
Terminal Connections
NAP and Redundant Cables
ControlNet cables, taps, connectors. Refer to the ControlNet Cable
System Planning and Installation manual (Publication 1786-6.2.1) for
descriptions of these components. For information on purchasing
these items, refer to the Allen-Bradley ControlNet Cable System
Component List (Publication AG-2.2).
Item
Catalog Number
RG-6 quad-shield
1786-RG6
Coax repeater
1786-RPT, -RPTD
Coax taps
1786-TPR, -TPS, -TPYR, -TPYS
Network access cable
1786-CP
Coax tool kit
1786-CTK
Segment terminators
1786-XT
BNC connectors
1786-BNC, -BNCJ, -BNCP, -BNCJ1
IMPORTANT
Publication 2711P-UM001C-EN-P
Do not connect to a network using both the
redundant cable BNC connector and the Network
Access Port (NAP).
Chapter
7
Transferring files and Upgrading Firmware
Chapter Objectives
This chapter covers information on how to:
• transfer applications using a Compact Flash Card or from a
computer.
• upgrade terminal firmware
Transferring Files Using a
Compact Flash Card
The PanelView Plus terminal allows you to copy or load files using a
compact flash card from RSView ME. To copy files in RSView ME
using a compact flash card, see page 4-17.
Transferring Files from a
Computer
Upgrading Firmware
IMPORTANT
For details on transferring .MER applications from a
computer to the PanelView Plus terminal, refer to
RSView Studio help or documentation.
The Firmware Upgrade Wizard (FUW) allows you to upgrade
firmware in the PanelView Plus terminal. Using the FUW, you can:
• create a firmware upgrade card (compact flash card) which you
then load in the card slot of terminal to upgrade firmware.
• upgrade firmware in a terminal that is connected to your
desktop computer using a Serial, Ethernet, or Network
connection via RSLinx Enterprise (for supported protocols).
The Firmware Upgrade Wizard is available in RSView Studio or with
the Firmware Upgrade Kit.
Preparing Terminal for Firmware Upgrade
Before starting the Firmware Upgrade Wizard, follow the steps below
to prepare the terminal for a successful upgrade.
1. Backup all .MER files on the terminal to an external storage card
or network.
2. Delete all applications on the terminal.
3. Record any Ethernet communication settings, such as IP address,
subnet masks, and gateways by selecting Terminal
Settings>Network and Communications>Network
Connections>Network Adapters>IP Address.
4. Disable the Auto-start feature on the terminal by selecting
Startup Options>RSView ME Station Startup and select Go to
Configuration Mode.
5. Reset the terminal.
1
Publication 2711P-UM001C-EN-P
7-2
Transferring files and Upgrading Firmware
Upgrading Firmware using a Compact Flash Card
This section shows how to upgrade the firmware in a PanelView Plus
terminal using a Compact Flash Card. This is a two step-process. First,
you create a firmware upgrade card with the necessary firmware files.
Second, you load this card in the target terminal to upgrade the
firmware.
1. Creating Firmware Upgrade Card
1. Start the Firmware Upgrade Wizard. Select Start>Rockwell
Software>RSView Enterprise>Firmware Upgrade Wizard.
2. Select Create firmware upgrade card.
• In the Firmware card location text box, select the destination
for the compact flash files (folder on the hard drive or physical
location of the compact flash card, e.g., E:\).
• From the Existing terminal list, select the type of PanelView
Plus terminal you are upgrading, then press Next.
Publication 2711P-UM001C-EN-P
Transferring files and Upgrading Firmware
7-3
3. From the Firmware source folder list, select the location of the
firmware files. The default location is C:\Program
Files\Rockwell Software\RSView Enterprise\FUPs.
From the Upgrade firmware version list, select the version of
the firmware you want to upgrade to, then press Next.
4. Select the appropriate KEPServer drivers and press Next. If no
KEPServer drivers are needed, just press Next.
TIP
If the selected FUP file does not support the
KEPServer drivers, this dialog will not appear.
Publication 2711P-UM001C-EN-P
7-4
Transferring files and Upgrading Firmware
5. Select Finish to copy the firmware source files to the location
specified in step 2.
TIP
If the files were created in a separate folder on
a local hard drive, copy the files to the root
directory of the compact flash card.
2. Upgrade Firmware in Terminal using Firmware Upgrade Card
1. Insert the compact flash card into the card slot of a powered
PanelView Plus terminal. A dialog appears indicating the
firmware upgrade is about to occur.
2. Press Upgrade to begin the firmware upgrade.
IMPORTANT
Publication 2711P-UM001C-EN-P
Do NOT remove the compact flash card while the
upgrade is in process.
Transferring files and Upgrading Firmware
7-5
3. If other PanelView Plus terminals exist on the same Ethernet
network, the following error may display:
"Error registering name on network (may be duplicate). Change
in system Control Panel and try again."
Ignore this error. It will be corrected during the upgrade. Press
OK to acknowledge error and wait for terminal to reset.
TIP
If a USB mouse is available you can
acknowledge this error by selecting OK.
4. On touch or touch/screen terminals, you must calibrate the
touch screen by selecting pointers in all four corners of the
screen and pressing the middle of the screen when prompted.
5. Ignore the following message if it appears. It means RSView ME
is being installed. Do not touch the two buttons that appear
with this message.
"Machine edition may be corrupted. Do you want to download
firmware?"
6. When the upgrade is complete, a dialog appears requesting you
to remove the compact flash card from the card slot. Remove the
card and press F8 or Exit to reset the terminal.
7. Communication settings are cleared when the terminal is
upgraded. If Ethernet communications is used, reconfigure the
Ethernet communication settings using the values recorded
when preparing the terminal.
8. Replace the .MER files that you backed up before starting the
upgrade or download a new .MER file to the terminal.
9. Load the .MER file and run the project.
TIP
You can configure your application to start
automatically on power cycle under Startup
Options.
Publication 2711P-UM001C-EN-P
7-6
Transferring files and Upgrading Firmware
Upgrading Firmware using a Network (Ethernet) Connection
You can upgrade the firmware in a terminal that is connected to a
desktop computer using a Serial, Ethernet or Network (using RSLinx
Enterprise) connection.
• Serial connection requires a RAS connection to be set up on
computer. During the RAS setup, you select the COM port.
• Ethernet connection requires that you enter the terminal’s IP
Address.
• Network connection requires RSLinx Enterprise where you
select the terminal on an existing network.
Both the Serial and Ethernet connection requires the PanelView Plus
File Transfer Utility running on the terminal.
This section shows how to upgrade firmware in a PanelView Plus
terminal using a Network connection via Ethernet communications.
1. Start the Firmware Upgrade Wizard. Select Start>Rockwell
Software>RSView Enterprise>Firmware Upgrade Wizard.
Publication 2711P-UM001C-EN-P
Transferring files and Upgrading Firmware
7-7
2. Select Upgrade firmware on terminal and press OK.
3. Select Network connection and press Next.
Use the Ethernet and Serial connections only if the firmware
upgrade is unsuccessful.
4. Locate the PanelView Plus terminal on your Ethernet network
via its IP address.
Skip to Step 6 if you found the terminal. If you do not see the
terminal, right click on the Ethernet driver and add the device to
the browse tree.
Publication 2711P-UM001C-EN-P
7-8
Transferring files and Upgrading Firmware
5. Double-click on EthernetIP Devices. Select the appropriate
terminal and press OK.
6. Enter the IP address for the terminal and press OK.
7. Select the terminal to be upgraded and press OK.
Publication 2711P-UM001C-EN-P
Transferring files and Upgrading Firmware
7-9
8. From the Firmware source folder text box, select the location
of the firmware files. The default location is C:\Program
Files\Rockwell Software\RSView Enterprise\FUPs.
From the Upgrade firmware version list, select the version of
the firmware you want to upgrade to, then select Next.
PanelView Plus 700
9. Select the appropriate KEPServer drivers and select Next. If no
KEPServer drivers are needed, just select Next.
TIP
If the selected FUP file does not support the
KEPServer drivers, this dialog will not appear.
Publication 2711P-UM001C-EN-P
7-10
Transferring files and Upgrading Firmware
10. Press Finish to start the upgrade.
11. Press Yes to continue the upgrade process. If the terminal was
properly prepared for the upgrade, no applications should be
running.
12. Firmware files are downloaded to the terminal. This may take
several minutes to 15 minutes. When the download is complete,
press OK to reset the terminal.
If other PanelView Plus terminals exist on the same Ethernet
network, the following error may display:
"Error registering name on network (may be duplicate). Change
in system Control Panel and try again."
Ignore this error. It will be corrected during the upgrade. Press
OK to acknowledge error and wait for terminal to reset.
TIP
Publication 2711P-UM001C-EN-P
If a USB mouse is available you can
acknowledge the error by selecting OK.
Transferring files and Upgrading Firmware
7-11
13. On touch or touch/screen terminals, you must calibrate the
touch screen by selecting pointers in all four corners of the
screen and pressing the middle of the screen when prompted.
14. Ignore the following message if it appears. It means RSView ME
is being installed. Do not touch the two buttons that appear with
the message.
"Machine edition may be corrupted. Do you want to download
firmware?"
15. Communication settings are cleared when the terminal is
upgraded. If Ethernet communications is used, reconfigure the
Ethernet communication settings using the values recorded
when preparing the terminal.
16. Replace the .MER files that you backed up before starting the
upgrade or download the new .MER files to the terminal.
17. Load the .MER file and run the project.
TIP
You can configure your application to start
automatically on power cycle under Startup
Options.
Publication 2711P-UM001C-EN-P
7-12
Transferring files and Upgrading Firmware
Publication 2711P-UM001C-EN-P
Chapter
8
Troubleshooting and Maintenance
Chapter Objectives
This chapter provides information on how to isolate and correct
common operating problems with system components.
• LED indicators
• general troubleshooting
• troubleshooting components (display, touch screen, keypad,
attached keyboard or mouse)
• Ethernet
• advanced troubleshooting
• startup error messages
• startup status messages
• system identification errors
• startup problems
• entering configuration mode
• restarting in safe mode
• cleaning the display window
LED Indicators
The PanelView Plus terminals have two LED indicators on the side of
unit to isolate operating problems:
• COMM indicator (green) for communications
• FAULT indicator (red) for hardware faults
•
COMM and Fault LEDs
1
Publication 2711P-UM001C-EN-P
8-2
Troubleshooting and Maintenance
General Troubleshooting
After a successful startup, both LEDs are
off and controlled by the application
running on the terminal.
This section provides a list of general troubleshooting steps to follow
when trying to isolate problems.
• Check for adequate power. An under-powered unit could
result in unpredictable behavior.
– The 400-600 DC powered terminals require 24V dc at 1.0 A
– The 400-600 AC powered terminals require 85…264V ac.
– The 700-1500 DC powered terminals require 24V dc at 1.5 A
– The AC Power Supply (2711P-RSACDIN) for 700-1500
terminals meets Class 2/SELV requirements.
• Check LED indicators on the terminal at startup. Is power
on? Is the unit attempting to start? The red LED should be Off,
except for a few brief flashes, and the green LED should be On.
– If the LEDs remain Off on the 700-1500 terminals, the power
supply or Logic Module has failed. Check the power cable.
Replace the Logic Module if the power is within range; if not,
replace the power supply.
– If the LEDs remain off on the 400-600 terminals, check the
power cable.
If the terminal powers up and stops during startup, the state of
the LEDs indicate the following:
Blinking red LED indicates a recoverable error.
Red LED
Green LED
Description
Blinking
Off
Last firmware download failed. Repeat
firmware download.
Blinking
Blinking
EBC boot loader firmware failed or is
missing. Load new EBC firmware
Blinking
ON
Windows CE OS firmware failed or is
missing. Load new CE OS firmware.
Solid red LED indicates a non-recoverable and fatal error.
Publication 2711P-UM001C-EN-P
Red LED
Green LED
Description
On
Off
Fatal hardware error occurred. Replace
Logic Module (700-1500) or the terminal
(400-600).
On
Blinking
Fatal hardware error occurred in Display.
Replace the Display Module (700-1500) or
the terminal (400-600).
Troubleshooting and Maintenance
8-3
• Check messages at startup for errors. Record any error
message and refer to the System Error Message table on page
8-10 for troubleshooting.
• Check voltages and temperatures (700-1500 only). From
Configuration Mode, open Terminal Settings>System
Information>Terminal Information.
– Battery Voltage for 700-1500 terminals should be at least 2.75
V. Replace the battery if less than 2.75 V.
– Display Temperatures should be less than 55 °C. The CPU
temperature should be less than 95 °C.
If the temperatures are higher, check for obstructed airflow
through the chassis and attempt to moderate the ambient
temperatures within the enclosure and surroundings.
• Check System Event Log for errors or unexpected reboots.
From Configuration Mode, open Terminal Settings>System Event
Log.
• Use Extended Diagnostics on 700-1500 terminals only to
perform more extensive hardware testing at startup. From
Configuration Mode, open Terminal Settings>Startup
Tests>Select Tests.
Select one or more of the tests you want to run. Enable
extended diagnostics and set the iteration or repeat count.
Restart the PanelView Plus terminal. The Serial Port test requires
a loopback connector with the following connections.
DB9 Connector (female)
N/C
1
RX
2
TX
3
DTR
4
N/C
5
DSR
6
RTS
7
CTS
8
N/C
9
Extended Diagnostics are performed at every startup until
disabled. A failure will momentarily halt startup and display an
error message.
Publication 2711P-UM001C-EN-P
8-4
Troubleshooting and Maintenance
Troubleshooting
Components
This section provides tips on how to isolate problems with individual
components of the PanelView Plus terminal, including the display,
touch screen, keypad, attached keyboard or mouse.
Display Problems
This section provides tips on how to isolate problems with the
Display.
• Check the brightness setting of the Display. Is the display
brightness dim or unreadable?
From Configuration Mode, open Terminal Settings>Display
Intensity.
• Check the contrast setting of Display for 400-600 grayscale
displays. From Configuration Mode, open Terminal
Settings>Display Contrast.
• Check the Screen Saver settings. Is the backlight turning off
or dimming the display unexpectedly.
From Configuration Mode, open Terminal
Settings>Display>Screen Saver.
• Check the LED indicators. Do they flash during startup? Is
power on and is the unit attempting to start?
• Check the Display temperature (700-1500 only). The
display intensity will decrease to 40% if its temperature (or the
temperature within the enclosure) is too high to reduce damage
to the display. This can be checked using the RSView ME Events
log.
• Check the startup messages. Is the Display operating at all
and do the startup messages appear? Record any error message
and use the System Error Message table on page 8-10 for
troubleshooting.
• Replace the Display Module if all other attempts do not
resolve problem (700-1500 only). If replacing the Display
Module corrects the problem, then the Display was not
functioning properly.
Publication 2711P-UM001C-EN-P
Troubleshooting and Maintenance
8-5
Touch Screen Problems
This section provides tips on how to isolate problems with the Touch
Screen.
• Check the catalog number of the unit. Verify that your
terminal has a touch screen by looking at the label on the
terminal.
• Perform a calibration of the touch screen. From
Configuration Mode, open Terminal Settings>Input
Devices>Touch Screen>Calibration. Follow the directions.
The calibration requires 5 user screen touches. When the
touches do not converge to a satisfactory calibration, you are
asked repeatedly for additional screen touches and the
calibration process never terminates. A touch screen that does
not calibrate is not present or not functioning properly. Replace
the Display Module (700-1500) or the terminal (400-600).
• Check the Cursor Enable setting for the touch screen. Is
the cursor visible? From Configuration Mode, open Terminal
Settings>Input Devices>Touch Screen>Cursor.
• Check the pointer input by attaching a USB mouse. If the
mouse works, but the touch screen does not, then the touch
driver or touch screen is not functioning properly. If both the
mouse and the touch screen are not working, then it is an
application problem.
• Does touching or dragging on the screen appear to work?
If yes, even if incorrectly, the touch screen is present and
working but requires calibration.
• Replace Bezel or Display Module if all other attempts do
not resolve the problem (700-1500 only). If replacing the
Display Module or bezel corrects the problem, then the touch
screen was not functioning properly.
Publication 2711P-UM001C-EN-P
8-6
Troubleshooting and Maintenance
Keypad Problems
This section provides tips on how to isolate problems with the
Keypad:
• Check Multi-Key/Hold-Off settings. From Configuration
Mode, open Terminal Settings>Keypad>Keypad Settings.
Is the Hold-Off Delay longer than expected, or are multiple key
presses inhibited by Multi-Key Lockout? Check all configurable
settings.
Home, End, Page Up or Page Down are not supported when
Multi-Key Lockout is enabled.
• Check key input by attaching a USB keyboard. If the
keyboard works, but the keypad does not, then the keypad
driver or keypad is not working. If both the keypad and
keyboard are not working, then the problem may be the
application.
• Replace the Display Module if all other attempts do not
resolve problem. If replacing the Display Module corrects the
problem, then the keypad was not functioning properly.
Problems with Attached Mouse
This section provides tips on how to isolate problems with an
attached Mouse.
• Check the Cursor Enable setting. Is the cursor visible? From
Configuration Mode, open Terminal Settings>Input
Devices>Touch Screen>Cursor. Also check mouse settings.
• Check the USB cable and connection. Detach and then
re-attach the mouse. Cycle power to the terminal.
• Is the mouse a USB composite device? If the mouse is a
keyboard/mouse composite device, then try a stand-alone USB
mouse.
• Replace the USB mouse. Try a different model or
manufacturer. See Appendix B for a list of compatible mouse
devices. You can also check the Knowledgebase at the
http://support.rockwellautomation.com site for a list of USB
devices that are compatible with the PanelView Plus terminal. If
attaching a new mouse resolves the problem, then the old
mouse was not working or non-compliant.
Publication 2711P-UM001C-EN-P
Troubleshooting and Maintenance
8-7
Problems with Attached Keyboard
This section provides tips on how to isolate problems with the
Keyboard.
• Check for enabled Alt-Ctrl keys. From Configuration Mode,
open Terminal Settings>Input Devices>Keyboard>Keyboard
Settings.
Are the keys enabled as expected? Check all configurable
settings in Keyboard Properties.
• If keypad is present, check input using the keypad. If the
keypad works, but the keyboard does not, then the keyboard
driver or keyboard is probably not working. If both the keypad
and the keyboard are not working, then it is probably an
application problem.
• Check the USB cable and connector. Detach and re-attach the
keyboard. Insure a good connection. Cycle power to the
terminal.
• Is the keyboard a USB composite device? If the keyboard is
a keyboard/mouse composite device, then try a stand-alone USB
keyboard.
• Replace the USB keyboard. Try a different model or
manufacturer. See Appendix B for a list of compatible
keyboards. You can also check the Knowledgebase at the
http://support.rockwellautomation.com site for a list of USB
devices that are compatible with the PanelView Plus terminal. If
a new keyboard resolves the problem, then the old keyboard
was probably non-compliant.
Publication 2711P-UM001C-EN-P
8-8
Troubleshooting and Maintenance
Ethernet Problems
• Check LED indicators at the Ethernet connector. The green
LED indicates a communications link and should be ON. The
amber LED indicates data activity and should be flashing. Verify
that there is a connection to the hub?
• Check cable connections and quality of cable. Check for
good connections and things such as quality, crimping, hub
connection, and uplink ports.
• Check IP Address of the Built-In Ethernet Controller. From
Configuration Mode, select Terminal Settings>Networks and
Communications>Network Connections>Network Adaptors.
If DHCP is enabled, the device expects a valid IP address to be
acquired within a several seconds after startup. The TCP/IP
protocol automatically assigns 169.254.nnn.nnn when it fails to
acquire an IP address from the server. In general, an IP address
that begins with 169 will not support a network connection.
A bad Ethernet connection and the absence of a valid IP address
are typically reported in a Communications error message box
with the Winsock critical error 10065 - "No route to host".
• Check for conflicting IP addresses. If DHCP is not enabled,
make sure the IP address you specify is not in conflict with the
address of another device on the network.
• Check the Device Name of the PanelView Plus terminal. Do
not allow devices on the network with same (host) name. From
Configuration Mode, open Terminal Settings>Communications
and Networks>Network Connections>Device Name.
• Contact your Network Administrator to check peer or
server settings. The “other side” of the Ethernet connection
may also be a problem.
Publication 2711P-UM001C-EN-P
Troubleshooting and Maintenance
Advanced Troubleshooting
8-9
1. Take advantage of alternate connectivity - mouse versus touch
screen, keyboard versus keypad, serial communications, and
alternate Ethernet connections.
2. Know useful keyboard shortcuts so that you can navigate
around the system without a mouse or touch screen.
3. From Configuration Mode, select Terminal Settings>System
Event Log to check the event log. Look for error conditions or
reasons for unexpected reboots.
4. Check the configuration settings in Configuration Mode for
incorrect settings.
5. Most importantly, general troubleshooting thoroughness means
getting answers to questions such as:
• Does the failure always happen? Is it repeatable?
• Does the failure happen at bootup or some other time? Is
there a set of actions that reveal the problem?
• Does the failure occur on just one terminal or on multiple
machines? If more than one machine, what do they have in
common? If not all machines, then what is different between
machines that fail and those that don’t?
• What appears on the screen, the LED indicators?
• Lastly, and most important; did everything work until
recently? If so, what changed?
Publication 2711P-UM001C-EN-P
8-10
Troubleshooting and Maintenance
Startup Error Messages
The following table provides a list of system error messages that may
display on startup. The messages apply to all PanelView Plus
terminals except where indicated.
IMPORTANT
Error Number
Displayed Message
Description
Recommended Action
1
RAM Test
POST RAM Test failure
Reset terminal. If error occurs again,
replace the terminal.
23
Internal CF
400-600: Firmware download failure
700 - 1500: Internal Compact Flash
Card access failure
Reset terminal. If error occurs again,
replace the terminal.
400-600: General error
Call technical support.
24
(1)
The 400-600 terminals display only the error number.
The 700-1500 terminals display both the error
number and the message.
25
EXE Valid
System firmware is incompatible
with the boot loader
Upgrade terminal with proper version of
firmware. See Chapter 7.
30
Watchdog Test
POST Watchdog Test failure
Reset terminal. If error occurs again,
replace the terminal.
31
Stuck Key
POST Stuck Key Test failure
Reset terminal. If error occurs again,
replace the terminal.
31.5
Stuck Touch
POST Stuck Touch Test failure
Reset terminal. If error occurs again,
replace the terminal.
32
Battery Test
POST dead battery failure
400-600: Replace terminal.
700-1500: Replace battery.
33.5(1)
NVRAM Access
Non-volatile memory access failure
Replace Logic Module.
34(1)
Display EEPROM
Display Module EEPROM data is
corrupted
Replace Display Module.
34.5(1)
Display Temp
Display Module over-temperature
failure
Reduce ambient temperature.
35.5(1)
CPU Temp
Processor over-temperature failure
Reduce ambient temperature.
40
EXE Check
System firmware is missing or
corrupt
Reload firmware using Firmware Upgrade
Wizard. See Chapter 8.
50
External CF
External Compact Flash card access
failure
Replace Compact Flash card. If replacing
the card does not correct the problem,
replace the terminal.
71
Eboot HW Test
Eboot failure
Reset terminal. If error occurs again,
replace the terminal.
The error number does not display on the PanelView Plus 400 - 600 terminals.
Publication 2711P-UM001C-EN-P
Troubleshooting and Maintenance
Startup Status Messages
Status Number
8-11
The following table provides a list of system status messages that
display at startup.
Description
Typical Operation
1
Validating RAM
Message displays for a few seconds.
2
Locating new OS image to download
Message displays for about 30 seconds.
11
Downloading OS image to RAM
Message displays for several minutes.
20
Erasing and programming Flash space Message displays for several minutes.
for OS image
70
Retrieving image from Ethernet
Message displays for several minutes.
24
Performing CRC of OS image in Flash
Message displays for a few seconds.
27
Decompressing from Flash to RAM
Message displays for about a minute.
28
Jumping to OS image
Message displays for just a second.
Publication 2711P-UM001C-EN-P
8-12
Troubleshooting and Maintenance
System Identification Errors
700-1500 only
The error messages in this section appear on startup if incorrect or
invalid components are used with the PanelView Plus 700-1500
terminals.
• The following dialog appears if a VersaView CE Logic Module is
attached to a PanelView Display Module or a PanelView Plus
Logic Module is attached to a VersaView CE Display Module. It
is recommended that you use a VersaView CE Display Module
with a VersaView CE Logic Module and a PanelView Plus
Display Module with a PanelView Plus Logic Module. This is a
warning allowing you to continue to operate.
• The following dialog appears if the PanelView Plus Logic
Module contains a 6189-RWx Internal Compact Flash card for
the VersaView CE terminal.
After pressing OK, you will be asked to power off the terminal
and insert a valid 2711P-RWx Internal Compact Flash card for
the PanelView Plus terminal.
• The following dialog appears if the VersaView CE Logic Module
contains a 2711P-RWx Internal Compact Flash card for the
PanelView Plus terminal
.
(6189-RWX)
After pressing OK, you will be asked to power of the terminal
and insert a valid 6189-RWx Internal Compact Flash card for the
VersaView CE terminal.
Publication 2711P-UM001C-EN-P
Troubleshooting and Maintenance
8-13
• The following dialog appears if the Internal Compact Flash in
the PanelView Plus Logic Module is corrupt or invalid. This is a
fatal error
After pressing OK, you will be asked to power of the terminal
and insert a valid 6189-RWx Internal Compact Flash card.
Startup Problems
If the PanelView Plus terminal is configured to enter Configuration
Mode at startup and does not, then reload the firmware. See page 7-1
for details.
If the application does not start, there may be a problem with the .mer
RSView Machine Edition file. Check for a startup screen and
compatible version.
Entering Configuration
Mode
To access configuration mode, your RSView .mer application must
contain a screen with a Goto Configure Mode button. When the
terminal is running the application, you can press this button to access
configuration mode.
Restarting in Safe Mode
Safe Mode is a diagnostics mode where the terminal is reduced to a
known state that permits recovery from a configuration or application
problem. Safe Mode ignores all user changes to the system and avoids
any problems that are due to interactions with end-user software or
changes. Once the system is running in Safe Mode, you can repair the
offending applications or changes that caused the problem.
700-1500 only
When the PanelView Plus terminal is restarted in Safe Mode, the
following occurs:
• The last configuration or the default configuration is used. The
last configuration is restored at the next reboot unless the
default configuration is saved (flushed), in which case it
becomes the new Persistent Registry.
• Depending on the state of the system, the touch screen may be
calibrated at startup.
Publication 2711P-UM001C-EN-P
8-14
Troubleshooting and Maintenance
To restart in Safe Mode:
The switches that control Safe Mode are located on the right side of
the Logic Module above the Compact Flash card slot.
• Insert a thin probe into the hole marked DEFAULT and press the
switch, then;
• Insert the probe into the hole marked RESET and press the
switch. The system will restart immediately into the Safe Mode
Cleaning the Display
Window
ATTENTION
Use of abrasive cleaners or solvents may damage the
display. Do not scrub or use brushes.
!
To clean the display window:
1. Disconnect power from the terminal at the power source.
2. Use a clean sponge or soft cloth with a mild soap or detergent to
clean the display.
3. Dry the display with a chamois or moist cellulose sponge to
avoid water spots.
Removing Paint and Grease
Remove fresh paint splashes and grease before drying by rubbing
lightly with isopropyl alcohol (70% concentration). Afterward, wash
using a mild soap or detergent. Rinse with clean water.
Use a protective antiglare overlay for easier cleaning of display
window.
Publication 2711P-UM001C-EN-P
Appendix
A
Specifications
Electrical
DC Power 400 - 600
Input Voltage DC
Power Consumption DC
DC Power 700 - 1500
Input Voltage DC
Power Consumption DC
AC Power 400 - 600
Input Voltage AC
Power Consumption AC
AC Power 700 - 1500 (2711P-RSAC)
Input Voltage AC
Power Consumption AC
24V dc nominal (18…32V dc)
25 Watts maximum (1.0 A at 24V dc)
24V dc nominal (18…30V dc)
70 Watts maximum (2.9 A at 24V dc)
85…264V ac, 47…63 Hz
60 VA maximum
85…264V ac, 47…63 Hz
120 VA maximum
Environmental
1
Operating Temperature
0…55 °C (32…131 °F)
Storage Temperature
-25…70 °C (-13 to 158 °F)
Heat Dissipation
400-600
700-1500
85 BTU/h
240 BTU/h
Relative Humidity
5…95% without condensation
Altitude Operating
2000 m (6561 ft)
Shock Operating
15 g at 11 ms
Shock Non-Operating
30 g at 11 ms
Vibration
10…57 Hz, 0.012 pk-pk displacement
57…500 Hz, 2 g pk acceleration
Enclosure Ratings
NEMA Type 12, 13, 4X (Indoor use only),
IP54, IP65
Publication 2711P-UM001C-EN-P
A-2
Specifications
Display
Display Type
400 & 600 Monochrome
600 - 1500 Color
Display Size, Diagonal
400
600
700
1000
1250 and 1250 High-Bright
1500
3.8 in
5.5 in
6.5 in
10.4 in
12.1 in
15.0 in
Display Area (W x H)
400
600
700
1000
1250 and 1250 High-Bright
1500
78 x 59 mm (3.07 x 2.32 in)
111 x 84 mm (4.37 x 3.30 in)
132 x 99 mm (5.20 x 3.90 in)
211 x 158 mm (8.31 x 6.22)
246 x 184 mm (9.69 x 7.25 in)
304 x 228 mm (11.98 x 8.98)
Resolution
400
600
700
1000
1250 and 1250 High-Bright
1500
320 x 240
320 x 240
640 x 480
640 x 480
800 x 600
1024 x 768
Backlight
400
600
LED
CCFL 50,000 hours life, minimum
Touch Screen
Touch Technology
Actuation Rating
Operating Force
Analog Resistive
1 million presses
10…110 g
Keypad
Function Keys(1)
Actuation Rating
Operating Force
Function keys, numeric and navigation
1 million presses
340 g
(1)
Publication 2711P-UM001C-EN-P
Monochrome Passive Matrix, Film
Compensated Super-Twist Nematic (FSTN)
Color Active Matrix TFT Thin-Film Transistor
with LCD Liquid Crystal Display
number of function keys varies by terminal size
Specifications
A-3
Mechanical
Weight (for base unit without modules)
400 Keypad(1)
600 Keypad or Keypad & Touch(1)
600 Touch(1)
700 Keypad or Keypad & Touch
700 Touch
1000 Keypad or Keypad & Touch
1000 Touch
1250 Keypad or Keypad & Touch
1250 Touch and 1250 High-Bright Touch
1500 Keypad or Keypad & Touch
1500 Touch
562 g (1.24 lb)
930 g (2.05 lb)
789 g (1.74 lb)
1.9 kg (4.2 lb)
1.7 kg (3.8 lb)
2.9 kg (6.3 lb)
2.6 kg (5.7 lb)
3.4 kg (7.6 lb)
3.2 kg (7.1 lb)
4.6 kg (10.0 lb)
4.2 kg (9.3 lb)
Dimensions H x W x D (for base unit without communication module)
(1)
400 Keypad
152 x 185 x 90 mm (6.0 x 7.28 x 3.54 in)
600 Keypad or Keypad & Touch
167 x 266 x 98 mm (6.58 x 10.47 x 3.86 in)
600 Touch
152 x 185 x 98 mm (6.0 x 7.28 x 3.86 in)
700 Keypad or Keypad & Touch
193 x 290 x 55 mm (7.58 x 11.40 x 2.18 in)
700 Touch
179 x 246 x 55 mm (7.04 x 9.68 x 2.18 in)
1000 Keypad or Keypad & Touch
248 x 399 x 55 mm (9.77 x 15.72 x 2.18 in)
1000 Touch
248 x 329 x 55 mm (9.77 x 12.97 x 2.18 in)
1250 Keypad or Keypad & Touch
282 x 416 x 55 mm (11.12 x 16.36 x 2.18 in)
1250 Touch
282 x 363 x 55 mm (11.12 x 14.30 x 2.18 in)
1250 Touch High Bright
282 x 363 x 74 mm (11.12 x 14.30 x 2.90 in)
1500 Keypad or Keypad & Touch
330 x 469 x 65 mm (12.97 x 18.46 x 2.55 in)
1500 Touch
330 x 416 x 65 mm (12.97 x 16.37 x 2.55 in)
Add approximately 95 g (0.21 lb) for communication module
General
Battery
400-600
700-1500
5 years minimum at 25 °C
2 years minimum at 25 °C
Clock
Battery-backed, +/-2 minutes per month
LED Indicators
COMM (Green), Fault (Red)
Application Flash Memory
5 MB
External Compact Flash Storage
512 MB maximum
Publication 2711P-UM001C-EN-P
A-4
Specifications
Agency Certifications
Agency Certifications
Marked for all applicable directives
When product is marked:
UL Listed Industrial Control Equipment
UL Listed Industrial Control Equipment for use in Canada
UL Listed Industrial Control Equipment for use in:
• Class I, Div 2 Group A, B, C, D
• Class I, Zone 2, Group IIC
• Class II, Div 2 Group F, G
• Class III, Hazardous Locations
Marked for all applicable acts
N223
Publication 2711P-UM001C-EN-P
Appendix
B
Compatible USB Devices
The following table provides a list of compatible USB devices which
can be used on the USB ports of the PanelView Plus terminals.
Device
USB Keyboard
USB
Keyboard/Mouse
USB Mouse
USB Hub
1
PanelView Plus
700-1500
PanelView Plus
400-600
Cat. No. 6189-KBDEPU1U
Yes
Yes
Ortek
MCK-600USB
Yes
Yes
Dell
RT7D10
Yes
Yes
Rockwell Automation
Cat. No. 6189-KBDEPC1U
Yes
Logitec
Optical Mouse - M-BJ58
Yes
Yes
Microsoft
Intellimouse D58-00026
Yes
Yes
Atek
USB Mouse
VersaView (Rockwell
Automation)
USB Mouse
Yes
Yes
Belkin
USB 4-Port Hub - ESU021
Yes
Yes
Vendor
Model
Rockwell Automation
Publication 2711P-UM001C-EN-P
B-2
Compatible USB Devices
Publication 2711P-UM001C-EN-P
Appendix
C
Available Fonts for Terminal Applications
The following fonts are pre-installed on PanelViewPlus/VersaView CE
terminals:
• True Type fonts (scalable)
– Tahoma.ttf (proportional)
– Courier.ttf (fixed width)
– Arial.ttf (proportional)
• (23) fonts of various sizes migrated from PanelView Standard
and PanelView "e" terminals (various sizes)
To simplify the creation and downloading of .mer application files on
these devices, use the above list of fonts when developing screens in
RSView Studio.
Additional fonts are available in RSView Studio when developing
application screens.
• If the font used to develop screens is not available on the target
device, the closest font is selected.
• If bolding or italics is used, and a separate bold or italics font is
unavailable, then the target operating system will use an
algorithm to produce these affects.
In either case, the device screens will look different than they do in
RSView Studio.
Downloading Fonts to
Terminal
To use additional fonts on a PanelView Plus/VersaView CE device,
copy any of the font files on the VersaView CE Accessories CD or the
RSView Machine Edition Fonts CD to the following directory on the
computer where RSView Studio is installed:
c:\Documents and Settings\All Users\Documents\RSView Enterprise\ME\Runtime
You can now use the File Transfer Utility in RSView Studio to
download the font file(s) to the target device:
1. Select Tools>Transfer Utility.
2. Select Source File>True Type Fonts.
3. Select a font file to download to the device and press the
Download button.
VersaView CE
Accessories CD
1
The following True Type fonts are included on the VersaView CE
Accessories CD:
• Times New Roman.ttf
• Symbol.ttf
• Wingdings.ttf
This CD is not supplied with PanelView Plus terminals.
Publication 2711P-UM001C-EN-P
C-2
Available Fonts for Terminal Applications
RSView Machine Edition
Fonts CD
Additional fonts are available on a CD, titled "RSView Machine Edition
Fonts". This CD is available from the Automation Bookstore
(www.theautomationbookstore.com) at no charge.
To download fonts that can be used on the PanelView Plus/VersaView
CE terminals via the network, see the Rockwell Automation
Knowledgebase (http://support.rockwellautomation.com). Select
Knowledgebase under Self-Service Support (or Online Tools) and then
enter Tech Note ID A66647102.
Fonts
File Name
Size (Bytes)
Arial (Subset 1_30)
arial_1_30.ttf
153,720
Arial Black
arialk.ttf
117,028
Arial Bold
arialbd.ttf
288,496
Arial Bold Italic
arialbi.ttf
226,748
Arial Italic
ariali.ttf
207,808
Comic Sans MS
comic.ttf
126,364
Comic Sans MS Bold
comicbd.ttf
111,476
Courier New (Subset 1_30)
cour_1_30.ttf
162,460
Courier New Bold
courbd.ttf
312,920
Courier New Bold Italic
courbi.ttf
236,148
Courier New Italic
couri.ttf
245,032
Arial
Comic Sans MS
Courier New
Georgia
Georgia
georgia.ttf
149,628
Georgia Bold
georgiab.ttf
141,032
Georgia Bold Italic
georgiaz.ttf
159,736
Georgia Italic
georgiai.ttf
157,388
Impact
impact.ttf
136,076
Kino
kino.ttf
28,872
MSLogo
mslogo.ttf
2,500
Symbol
symbol.ttf
69,464
Tahoma (Subset 1_07)
tahoma_1_07.ttf
123,980
Tahoma Bold
tahomabd.ttf
295,432
Times New Roman (Subset 1_30)
times_1_30.ttf
184,976
Times New Roman Bold
timesbd.ttf
334,944
Times New Roman Bold Italic
timesbi.ttf
239,692
Times New Roman Italic
timesi.ttf
248,368
Tahoma
Times New Roman
Publication 2711P-UM001C-EN-P
Available Fonts for Terminal Applications
Fonts
File Name
C-3
Size (Bytes)
Trebuchet MS
Trebuchet MS
trebuc.ttf
69,688
Trebuchet MS Bold
trebucbd.ttf
66,444
Trebuchet MS Bold Italic
trebucbi.ttf
66,348
Trebuchet MS Italic
trebucit.ttf
72,560
Verdana
verdana.ttf
149,752
Verdana Bold
verdanab.ttf
137,616
Verdana Bold Italic
verdanaz.ttf
154,800
Verdana Italic
Verdana
verdanai.ttf
155,076
Webdings
webdings.ttf
118,752
Wingding
wingding.ttf
81,000
Simsun & NSimSun
simsun.ttc
10,500,400
Simsun & NSimSun (Subset 2_50)
simsun_2_50.ttc
3,051,024
Simsun & NSimSun (Subset 2_60)
simsun_2_60.ttc
3,578,692
Simsun & NSimSun (Subset 2_70)
simsun_2_70.ttc
6,975,948
Simsun & NSimSun (Subset 2_80)
simsun_2_80.ttc
8,116,188
Simsun & NSimSun (Subset 2_90)
simsun_2_90.ttc
9,066,640
sunfon.ttf
4,686,044
MingLiU & PMingLiU
mingliu.ttc
8,822,400
MingLiU & PMingLiU (Subset 2_70)
mingliu_2_70.ttc
4,786,488
MingLiU & PMingLiU (Subset 2_80)
mingliu_2_80.ttc
5,772,700
MingLiU & PMingLiU (Subset 2_90)
mingliu_2_90.ttc
7,354,808
msming.ttf
3,172,552
MS Gothic & P Gothic & UI Gothic
msgothic.ttc
8,272,028
MS Gothic & P Gothic & UI Gothic (Subset 1_50)
msgothic_1_50.ttc
4,456,536
MS Gothic & P Gothic & UI Gothic (Subset 1_60)
msgothic_1_60.ttc
6,057,400
Chinese (Simplified) Locale Specific Support
Simsun & NSimSun
SC_Song
Chinese (Traditional) Locale Specific Support
MingLiU & PMingLiU (Choose 1)
MSMing
Japanese Locale Specific Support
MS Gothic
MS Gothic & P Gothic & UI Gothic (Subset 1_70)
msgothic_1_70.ttc
3,795,500
MS Gothic & P Gothic & UI Gothic (Subset 1_80)
msgothic_1_80.ttc
5,438,776
MS Gothic & P Gothic & UI Gothic (Subset 1_90)
msgothic_1_90.ttc
6,408,352
MS Gothic & P Gothic (Subset 30)
msgothic30.ttc
4,197,524
MS Gothic & P Gothic (Subset 30_1_19)
msgothic30_1_19.ttc
3,304,056
Publication 2711P-UM001C-EN-P
C-4
Available Fonts for Terminal Applications
Fonts
File Name
Size (Bytes)
gl_ce.ttf
4,130,084
Gulim & GulimChe (Subset 1_30)
gulim_1_30.ttc
3,010,268
Gulim & GulimChe (Subset 1_40)
gulim_1_40.ttc
4,683,896
Gulim & GulimChe (Subset 1_50)
gulim_1_50.ttc
7,128,756
Gulim & GulimChe (Subset 1_60)
gulim_1_60.ttc
9,360,100
Korean Locale Specific Support
GL_CE
Gulim & GulimChe (Choose 1)
Publication 2711P-UM001C-EN-P
Index
A
AC power
400-600 3-5
700-1500 1-9, 3-5
AC power supply 700-1500 1-16
installation 5-19
accessories 1-12
adapter plates 1-15
application
loading .mer 4-4
running .mer 4-5
B
backlight
brightness 4-19
replacement 1-14, 5-16
base unit
400-600 1-3
700-1500 1-8
battery replacement 1-17, 5-12
bezel replacement 1-14, 5-14
C
cables 1-16
runtime communication cables 6-2
catalog number configuration 1-12
cleaning display 8-14
communication adapters 1-16
communication modules 1-13
400-600 1-4
700-1500 1-9
installing and replacing 5-6, 5-8
communications
cables 6-2
ControlNet 6-16
DH+/DH485/RIO module 6-11, 6-16
DH485 4-9, 6-12
DHPlus 4-9, 6-14
Ethernet 4-12, 6-9
Remote I/O 6-15
serial 4-10, 6-6
USB ports 6-5
compatibility of components 5-2
configuration mode
loading application 4-4
running application 4-5
terminal settings 4-5
ControlNet
cables 6-18
compatible controllers 6-17
configuration 4-10
ControlNet protocol 6-16
overview 6-16
copying files
applications 4-17
font files 4-17
cutout dimensions for each terminal 2-5
D
date 4-36
date format 4-41
DC power 3-3, A-1
SELV power supply 3-4
deleting files
applications 4-16
font files 4-16
log files 4-16
DH485
cables 6-2
configuration 4-9
network wiring 6-12
port connectors 6-11, 1-1
settings in configuration mode 4-9
DHPlus
cables 6-2
configuration 4-9
network connections 6-14
port connectors 6-11
settings in configuration mode 4-9
diagnostics
in Configuration Mode 4-15
display
400-600
troubleshooting 8-4
display 400-600
keypad 1-6
keypad/touch 1-6
touch screen 1-5
display modules
high-bright display 1-10, 1-12, 2-4
display modules 700-1500 1-12
keypad 1-11
keypad/touch 1-11
replacing 5-10
touch screen 1-10
troubleshooting 8-4
display settings
in configuration mode 4-19
Publication 2711P-UM001C-EN-P
2
Index
E
Ethernet
cables 6-2, 6-10
configuration 4-12
connector pinout 6-9
troubleshooting 8-8
European Communities Directive
Compliance Preface-iii
external compact flash cards 1-14,
5-21
F
firmware upgrade
creating a firmware upgrade card 7-2
firmware upgrade wizard 7-1
upgrading from a computer 7-6
using a firmware upgrade card 7-4
firmware upgrade kits 1-17
font linking 4-21
fonts
additional fonts C-1
pre-installed C-1
function keys
keypad terminals 1-6, 1-11
H
hardware monitor 4-33
hazardous locations 2-1
USB port 2-2
high-bright display 1-10, 2-4
I
IGMP Protocol 6-10
input devices
keyboard 4-22
keypad 4-22
mouse 4-25
touch screen 4-24
input panel 4-3
installation 2-1
1000 mounting dimensions 2-9
1250 mounting dimensions 2-10
1500 mounting dimensions 2-11
400 mounting dimensions 2-6
600 mounting dimensions 2-7
700 mounting dimensions 2-8
ambient temperature 2-4
Publication 2711P-UM001C-EN-P
backlight 5-16
battery 5-12
bezel 5-14
clearances 2-4
communication module 5-6, 5-8
display module 700-1500 5-10
enclosures 2-3
environment 2-3
hazardous locations 2-1
high-bright display 2-4
legend inserts 5-20
mounting clips 700-1500 2-15
mounting levers 400-600 2-13
panel cutout dimensions 2-5
panel installation 400-600 2-12
panel installation 700-1500 2-14
product label 5-19
required tools 2-5
intended audience Preface-ii
internal compact flash
compatibility 5-2
installing and replacing 5-3
Internet Group Management Protocol
(IGMP) 6-10
IP address 4-13
K
keyboard
troubleshooting 8-7
keyboard settings 4-22
keyboard/mouse
compatible A-1
keyboards, compatible A-1
keypad legend inserts 1-14, 5-20
keypad settings 4-22
troubleshooting 8-6
L
languages 4-39
LED indicators 8-1
legend inserts
installation 5-20
loading application 4-4
logic module 1-13
logic module 700-1500
compatibility 5-2
features 1-8
installing and replacing 5-4
Index
M
memory
allocations 4-34
installing and replacing 5-3
messages
startup error 8-10
startup status 8-11
modular components 700-1500 1-8
mounting clips 700-1500 1-17, 2-15
mounting dimensions
1000 2-9
1250 2-10
1500 2-11
400 2-6
600 2-7
700 2-8
mounting levers 400-600 1-17, 2-12
mouse 4-25, 6-5
troubleshooting 8-6
mouse, compatible A-1
multikey lockout 4-23
N
network connections 4-11
O
outdoor installation
high-bright displays 2-4
P
packing list Preface-i
power terminal block 3-2
print setup
for alarms 4-26
for diagnostic messages 4-26
for displays 4-26
product components 1-12
R
RAM 1-13
compatibility 5-2
installing and replacing 5-3
3
Remote I/O
cables 6-2, 6-15
connection 6-15
port connectors 6-11
settings 4-9, 4-10
reset switch
400-600 3-6
700-1500 3-7
resetting terminal 4-2
400-600 3-6
700-1500 3-7
RSView ME
firmware number 4-35
S
safe mode 3-7, 8-13
screen saver 4-20
serial communications
computer connection 6-8
DF1 6-6
DH485 6-6
null modem cable 6-7
ports 6-6, 6-9
printing 6-6, 6-8
transferring applications 6-6
using a modem 6-7
serial connections 6-6
serial settings 4-10
Simple Network Management Protocol
(SNMP) 6-10
SNMP Protocol 6-10
software 1-1
specifications
agency certifications A-4
electrical A-1
environmental A-1
mechanical A-3
startup error messages 8-10
startup problems 8-13
startup settings 4-28
startup status messages 8-11
startup tests 4-30
support 4-35
system event log 4-32
system identification errors 8-12
Publication 2711P-UM001C-EN-P
4
Index
T
terminal block, power 3-2
terminal information 4-33
terminal settings 4-5
copying files 4-17
date 4-36
deleting files 4-16
DH485 4-9
DHPlus 4-9
diagnostics 4-15
display 4-19
file management 4-16
input devices 4-22
long date format 4-42
memory allocation 4-34
network connections 4-11
numeric format 4-39
print setup 4-26
regional settings 4-39
Remote I/O 4-9, 4-10
RSView ME info 4-35
screen saver 4-20
serial 4-10
short date format 4-41
startup options 4-28
startup tests 4-30
system event log 4-32
system information 4-33
terminal info 4-33
time 4-37
time format 4-40
time zone 4-38
time/date/regional settings 4-36
Publication 2711P-UM001C-EN-P
time 4-37
time format 4-40
touch screen
calibration 4-24
cursor enable 4-24
double-tap sensitivity 4-25
troubleshooting 8-5
troubleshooting 8-1
display module 8-4
Ethernet 8-8
general 8-2
keyboard 8-7
keypad 8-6
LED indicators 8-1
starting in safe mode 3-7, 8-13
startup error messages 8-10
startup problems 8-13
startup status messages 8-11
system identification errors 8-12
touch screen 8-5
U
USB devices A-1
USB ports 6-5
compatible A-1
connector pinouts 6-5
terminals 2-2
USB Hub A-1
W
wiring and safety guidelines 3-1, 6-1
Allen-Bradley, ControlLogix, DH+, PLC-2, PLC-3, PLC-5, RSView, SLC and VersaView are registered trademarks
of Rockwell Automation.
CompactLogix, FlexLogix, InView, Logix, MicroLogix, PanelView, PanelView Plus, RSLogix, RSView32 and
SoftLogix are trademarks of Rockwell Automation.
ControlNet is a trademark of ControlNet International, Ltd.
DeviceNet is a trademark of the Open DeviceNet Vendor Association.
Ethernet is a trademark of Digital Equipment Corporation, Intel and Xerox Corporation.
Microsoft, Windows, Windows CE, Windows NT, Windows 2000 and Windows XP are registered trademarks of
Microsoft in the U.S. and other countries.
Publication 2711P-UM001C-EN-P - October 2004 7
Supersedes Publication 2711P-UM001B-EN-P - August 2003
Copyright © 2004 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement